Kenwood FPX930 User Manual
instructions
instructions
FPX930 series
«∞∑FKOLU‹
œß∑u¸«∞FLKNU
English 2 - 8
Français 9 - 17
´¸∂w
52 - 13
≠U¸ßv
81 - 42
0.3
0.5
0.7
1.1
1.3
1.5
0.9
0.3
0
.
5
0
.7
1.1
1
.3
1
.5
0.9
A
+
+++
before using your Kenwood appliance
●
Read these instructions carefully and retain for future
reference.
●
Remove all packaging and any labels.
safety
●
The blades and discs are very sharp, handle with care.
Always hold by the finger grip at the top,
away from the cutting edge, both when handling
and cleaning.
●
Do not lift or carry the processor by the handle - or the
handle may break resulting in injury.
●
Always remove the knife blade before pouring contents from
the bowl.
●
Keep hands and utensils out of the processor bowl and
liquidiser goblet whilst connected to the power supply.
●
Switch off and unplug:
●●
before fitting or removing parts
●●
when not in use
●●
before cleaning
●
Never use your fingers to push food down the feed tube.
Always use the pusher/s supplied.
●
Never fit the blade unit to the power unit without
the liquidiser or mill jar fitted.
●
Before removing the lid from the bowl or liquidiser or mini
chopper/mill from the power unit:-
●●
switch off;
●●
wait until the attachment/blades have completely
stopped;
●●
be careful not to unscrew the liquidiser goblet or mini
chopper/mill from the blade assembly.
●
Liquids should be allowed to cool to room temperature
before blending.
●
Do not use the lid to operate the processor, always use the
on/off speed control.
●
This appliance will be damaged and may cause
injury if the interlock mechanism is subjected to
excessive force.
●
Always unplug your food processor when not in
use.
●
Never use an unauthorised attachment.
●
Never leave the appliance unattended when it is operating.
●
Never use a damaged appliance. Get it checked or repaired:
see ‘service & customer care’.
●
Never let the power unit, cord or plug get wet.
●
Don’t let excess cord hang over the edge of a table or
worktop or touch hot surfaces.
●
Do not exceed the maximum capacities stated in the
recommended speed chart.
●
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
●
Children should be supervised to ensure that they do not
play with the appliance.
●
Only use the appliance for its intended domestic use.
Kenwood will not accept any liability if the appliance is
subject to improper use, or failure to comply with these
instructions.
●
Misuse of your processor/liquidiser can result in injury.
●
The maximum rating is based on the attachment that draws
the greatest load. Other attachments may draw less power.
Refer to the relevant section under “using the attachments”
for additional safety warnings for each individual attachment.
before plugging in
●
Make sure your electricity supply is the same as the one
shown on the underside of your appliance.
●
This appliance conforms to EC directive 2004/108/EC on
Electromagnetic Compatibility and EC regulation no.
1935/2004 of 27/10/2004 on materials intended for contact
with food.
before using for the first time
1 Remove the plastic blade covers from the knife blade. Take
care the blades are very sharp. These covers should
be discarded as they are to protect the blade during
manufacture and transit only.
2 Wash the parts see ‘care & cleaning’
key
processor
power unit
detachable drive shaft
bowl
lid
feed tube
pushers
safety interlocks
cord storage (at back)
speed/pulse control
power on light
liquidiser
filler cap
lid
lid seal
goblet
sealing ring
blade unit
mini chopper/mill
blade unit
sealing ring
jar
sprinkler lid
additional attachments
knife blade
dough tool
twin beater geared metal whisk
maxi-blend canopy
thick slicing/coarse grating disc
thin slicing/fine grating disc
fine (Julienne style) chipper disc
rasping/parmesan disc
citrus juicer
mini processor bowl
centrifugal juicer
KENSTORE™ attachments carousel
spatula
22
to use your food processor
1 Fit the detachable shaft onto the power unit .
2 Then fit the bowl. Place the handle towards the back and
turn clockwise until it locks .
3 Fit an attachment over the drive shaft.
●
Always fit the bowl and attachment onto the processor
before adding ingredients.
4 Fit the lid - ensuring the top of the drive shaft locates into
the centre of the lid.
●
Do not use the lid to operate the processor,
always use the on/off speed control.
5 Plug in and the power on light will come on. Switch on and
select a speed. (Refer to the recommended speed chart).
●
The processor will not operate if the bowl or lid
are not fitted correctly to the interlock. Check
that the feed tube and bowl handle are situated
to the right hand side.
●
Use the pulse (P) for short bursts. The pulse will operate for
as long as the control is held in position.
6 Reverse the above procedure to remove the lid, attachments
and bowl.
●
Always switch off and unplug before removing the
lid.
important
●
Your processor is not suitable for crushing or grinding coffee
beans, or converting granulated sugar to caster sugar.
●
When adding almond essence or flavouring to mixtures
avoid contact with the plastic as this may result in
permanent marking.
to use your liquidiser
1 Fit the sealing ring into the blade unit - ensuring the
seal is located correctly. Leaking will occur if the seal
is damaged or incorrectly fitted.
2 Screw the goblet onto the blade assembly.
3 Put your ingredients into the goblet.
4 Push the lid seal onto the underside of the lid.
5 Fit and lock the filler cap in the lid, by turning one position
.
6 Fit the lid to the goblet and turn the filler cap to to
lock.
The filler cap can be located in 3 different positions (see A)
- filler cap removable for adding ingredients to the
goblet.
- lid unlocked/filler cap locked to the lid for fitting and
removing the lid.
- lid locked.
7 Place the liquidiser onto the power unit and turn to lock .
●
The appliance will not operate if the liquidiser is
incorrectly fitted to the interlock.
8 Select a speed (refer to the recommended speed chart) or
use the pulse control.
●
Liquids should be allowed to cool to room
temperature before blending.
hints
●
When making mayonnaise, put all the ingredients, except the
oil into the liquidiser. Then with the machine running, pour the
oil into the filler cap and let it run through.
●
Thick mixtures, eg pates and dips, may need scraping
down. If it’s difficult to process, add more liquid.
●
Ice crushing - operate the pulse in short bursts until crushed to
the desired consistency.
●
To ensure the long life of your liquidiser, never run it for longer
than 60 seconds. Switch off as soon as you’ve got the right
consistency.
3
choosing a speed for all functions
tool/Attachment function speed maximum
capacities
knife blade One Stage Cake Mix 1 – 8 1.5Kg
Pastry - rubbing fat into flour 5 – 8 340g
Adding water to combine pastry ingredients 1 – 5
Chopping/pureeing/pates 8 600g
knife blade with maxi-blend canopy Soups – start at a low speed and move up to Max 1 – 8 1.5 litres
whisk Egg Whites 8 6 Egg Whites
Egg & sugar for fatless sponges 8
Cream 5 – 8 500 mls
dough tool Yeasted mixes 8 600g
discs – slicing/grating/chipping Firm food items such as carrots, hard cheese. 5 – 8
Softer items such as cucumbers, tomatoes 1 – 5
rasping disc Parmesan cheese, Potato for German potato dumplings 8
citrus juicer Citrus fruits 1
mini bowl All processing 8 200g
liquidiser All processing 8 1.5 litres
mini chopper/mill Herbs 8 10g
Nuts & Coffee Beans 8 50g
centrifugal juicer Fruits & Vegetables 8 500g
●
The processing of spices is not recommended as they may
damage the plastic parts.
●
The appliance will not work if the liquidiser is incorrectly
fitted.
●
To blend dry ingredients - cut into pieces, remove the filler
cap, then with the appliance running, drop the pieces down
one by one. Keep your hand over the opening. For best
results empty regularly.
●
Don’t use the liquidiser as a storage container. Keep it
empty before and after use.
●
Never blend more than 11⁄2 litres - less for frothy liquids like
milkshakes.
Note: The mini chopper/mill base is not
interchangeable with the glass liquidiser goblet.
The processor will not operate if the wrong base
is fitted. Refer to graphics on blade unit bases.
to use your mini chopper/mill
Use the mini chopper/mill for milling herbs, nuts and coffee
beans.
1 Put your ingredients into the jar.
2 Fit the sealing ring into the blade unit .
3 Turn the blade unit upside down. Lower it into the jar, blades
down.
4 Screw the blade unit onto the jar until it is finger tight.
5 Place the mini chopper/mill onto the power unit and turn to
lock .
6 Switch on to maximum speed or use the pulse control.
7 After milling, you can replace the blade unit with the sprinkler
lid and shake out your food.
●
The sprinkler lid is not airtight.
safety
●
Never fit the blade unit to your food processor without the
jar fitted.
●
Never unscrew the jar while the mini chopper/mill is fitted to
your appliance.
●
Do not touch the sharp blades – Keep the blade unit away
from children.
●
Never remove the mini chopper/mill until the blades have
completely stopped.
●
To ensure the long life of your mini chopper/mill, never run
for longer than 30 seconds. Switch off as soon as you have
got the right consistency.
●
The processing of spices is not recommended as they may
damage the plastic parts.
●
The appliance will not work if the mini chopper/mill is
incorrectly fitted.
●
Use for dry ingredients only.
hints
Herbs are best milled when clean and dry.
●
Note: The mini chopper/mill base is not
interchangeable with the glass liquidiser goblet.
The processor will not operate if the wrong base
is fitted. Refer to graphics on blade unit bases.
using the attachments
Refer to recommended speed chart for each attachment.
knife blade
The knife blade is the most versatile of all the attachments.
The length of the processing time will determine the texture
achieved. For coarser textures use the pulse control.
Use the knife blade for cake and pastry making, chopping
raw and cooked meat, vegetables, nuts, pate, dips,
pureeing soups and to also make crumbs from biscuits and
bread.
hints
●
Cut food such as meat, bread, vegetables into cubes
approximately 2cm/3⁄4in before processing.
●
Biscuits should be broken into pieces and added down the
feed tube whilst the machine is running.
●
When making pastry use fat straight from the fridge cut into
2cm/3⁄4in.cubes.
●
Take care not to over-process.
dough tool
Use for yeasted dough mixes.
●
Place the dry ingredients in the bowl and add the liquid
down the feed tube whilst the machine is running. Process
until a smooth elastic ball of dough is formed this will take
60 - 90 secs.
●
Re-knead by hand only. Re-kneading in the bowl is not
recommended as it may cause the processor to become
unstable.
twin beater geared whisk
Use for light mixtures only eg egg whites, cream, evaporated
milk and for whisking eggs and sugar for fatless sponges.
Heavier mixtures such as fat and flour will damage it.
using the whisk
1 Fit the drive shaft and bowl onto the power unit.
2 Push each beater securely into the drive head .
3 Fit the whisk by carefully turning until it drops over the drive
shaft.
4 Add the ingredients.
5 Fit the lid - ensuring the end of the shaft locates into the
centre of the lid.
6 Switch on.
important
●
The whisk is not suitable for making one-stage
cakes or creaming fat and sugar as these mixes
will damage it. Always use the knife blade for
cake making.
hints
●
Best results are obtained when the eggs are at room
temperature.
●
Ensure the bowl and whisks are clean and free from grease
before whisking.
●
Carefully fold in flour and sugar by hand using a metal spoon
for fatless sponges and meringues.
4
maxi-blend canopy
When blending liquids, use the maxi-blend canopy with the
knife blade. It allows you to increase the liquid processing
capacity from 1 litre to 1.5 litres, prevents leaking and
improves the chopping performance of the blade.
1 Fit the drive shaft and bowl onto the power unit.
2 Fit the knife blade.
3 Add ingredients to be processed.
4 Fit the canopy over the top of the blade ensuring it sits on
the ledge inside the bowl . Do not push down on
the canopy, hold by the centre grip.
5 Fit the lid and switch on.
slicing/grating discs
reversible slicing/grating discs - thick , thin
Use the grating side for cheese, carrots, potatoes and foods
of a similar texture.
Use the slicing side for cheese, carrots, potatoes, cabbage,
cucumber, courgette, beetroot and onions.
fine (Julienne style) chipper disc
Use to cut: potatoes for Julienne style French fries; firm
ingredients for salads, garnishes, casseroles and stir fries (eg
carrot, swede, courgette, cucumber).
rasping disc
Grates Parmesan cheese and potatoes for German potato
dumplings.
safety
●
Never remove the lid until the cutting disc
has completely stopped.
●
Handle the cutting discs with care - they are
extremely sharp
to use the cutting discs
1 Fit the drive shaft and bowl onto the power unit.
2 Holding by the centre grip , place the disc onto the drive
shaft with the appropriate side uppermost .
3 Fit the lid.
4 Choose which size feed tube you want to use. The pusher
contains a smaller feed tube for processing individual items
or thin ingredients.
To use the small feed tube - first put the large pusher inside
the feed tube.
To use the large feed tube - use both pushers together.
5 Put the food in the feed tube.
6 Switch on and push down evenly with the pusher - never
put your fingers in the feed tube.
hints
●
Use fresh ingredients
●
Don’t cut food too small. Fill the width of the large feed tube
fairly full. This prevents the food from slipping sideways
during processing. Alternatively use the small feed tube.
●
When using the chipper disc, place ingredients horizontally.
●
When slicing or shredding: food placed upright comes
out shorter than food placed horizontally .
●
There will always be a small amount of waste on the plate or
in the bowl after processing.
citrus juicer
Use the citrus juicer to squeeze the juice from citrus fruits
(eg oranges, lemons, limes and grapefruits).
cone
sieve
to use the citrus juicer
1 Fit the drive shaft and bowl onto the power unit.
2 Fit the sieve into the bowl - ensuring the sieve handle is
locked into position directly over the bowl handle .
3 Place the cone over the drive shaft turning until it drops all
the way down .
4 Cut the fruit in half. Then switch on and press the fruit onto
the cone.
●
The citrus juicer will not operate if the sieve is
not locked correctly.
●
For best results store and juice the fruit at room temperature
and hand roll on a worktop before juicing.
●
To help with juice extraction move the fruit from side to side
when juicing.
●
When juicing large quantities, empty the strainer regularly to
prevent the build up of pulp and seeds.
mini processor bowl
Use the mini processor bowl to chop herbs and process
small quantities of ingredients e.g. meat, onion, nuts,
mayonnaise, vegetables, purées, sauces and baby food.
mini processor knife blade
mini processor bowl
to use the mini processor bowl
1 Fit the drive shaft and bowl onto the power unit.
2 Fit the mini processor bowl - ensuring the ribs on the inside
of the mini bowl chimney align with the slots in the main
bowl chimney .
3 Place the knife blade over the drive shaft .
4 Add the ingredients to be processed.
5 Fit the lid and switch on.
safety
●
Never remove the lid until the knife blade has completely
stopped.
●
The knife blade is very sharp - always handle with care.
important
●
Do not process spices – they may damage the plastic.
●
Do not process hard food such as coffee beans, ice cubes
or chocolate – they may damage the blade.
hints
●
Herbs are best chopped when clean and dry.
●
Always add a little liquid when blending cooked ingredients
to make baby food.
●
Cut foods such as meat, bread, vegetables into cubes
approximately 1-2 cm (1⁄2 – 3⁄4 in) before processing.
●
When making mayonnaise add the oil down the feed tube.
5
metal centrifugal juicer
Use the centrifugal juicer for making juice from firm fruit
and vegetables.
pusher
centrifugal lid
pulp remover
filter drum
juicer drive shaft
to use the centrifugal juicer
1 Fit the juicer drive shaft and bowl onto the power unit.
2 Place the pulp remover into the filter drum - ensuring
the tabs locate with the slots in the bottom of the drum .
3 Fit the filter drum .
4 Place the attachment lid onto the bowl and turn until it
locks . Your juicer will not operate if the bowl or
lid are not fitted correctly into the interlock .
5 Place a suitable glass or jug under the juice outlet.
6 Cut the food to fit the feed tube.
7 Switch on and push down evenly with the pusher - never
put your fingers in the feed tube. Process fully before
adding more.
●
After adding the last piece, let the juicer run for a further 30
seconds to extract all the juice from the filter drum.
safety
●
Do not use the juicer if the filter is damaged.
●
The cutting blades on the base of the filter drum are very
sharp, take care when handling and cleaning the drum.
●
Only use the pusher supplied. Never put your fingers in the
feed tube. Unplug before unblocking the feed tube.
●
Before removing the lid, switch off and wait for the filter to
stop.
important
●
If the juicer starts to vibrate, switch off and empty the pulp
from the drum. (The juicer vibrates if the pulp becomes
unevenly distributed).
●
Maximum capacity that can be processed at one time is
500g of fruit or vegetables.
●
Some very hard foods may make your juicer slow down or
stop. If this happens switch off and unblock the filter.
●
Switch off and clear the pulp collector regularly during use.
hints
●
Before processing remove stones and pips (eg pepper,
melon, plum) and tough skins (eg melon, pineapple). You
don’t need to peel or core apples and pears.
●
Use firm, fresh fruit and vegetables.
●
Citrus fruit - peel and remove the white pith, otherwise the
juice may taste bitter. For best results use the citrus juicer.
KENSTORE™ attachments carousel
Your food processor is supplied with an attachment storage
carousel that fits inside the bowl.
to use the storage carousel
1 Fit the knife blade to the bowl.
2 Then fit the whisk, discs and canopy into the carousel .
3 Fit the carousel over the knife blade and place the processor
lid on top .
care & cleaning
●
Always switch off and unplug before cleaning.
●
Handle the blades and cutting discs with care they are extremely sharp.
●
Some foods may discolour the plastic. This is perfectly
normal and won’t harm the plastic or affect the flavour of
your food. Rub with a cloth dipped in vegetable oil to remove
the discolouration.
power unit
●
Wipe with a damp cloth, then dry. Ensure that the interlock
area is clear of food debris.
●
Store excess cord in the storage area at the back of the
power unit .
liquidiser/mini chopper/mill
1 Empty the goblet/jar before unscrewing it from the blade
unit.
2 Wash the goblet/jar by hand.
3 Remove and wash the seals.
4 Don’t touch the sharp blades – brush them clean using hot
soapy water, then rinse thoroughly under the tap. Don’t
immerse the blade unit in water.
5 Leave to dry upside down.
twin beater geared whisk
●
Detach the beaters from the drive head by gently pulling
them free. Wash in warm soapy water.
●
Wipe the drive head with a damp cloth, then dry.
Do not immerse the drive head in water.
centrifugal filter drum
●
Lift out the pulp remover and tap lightly to release the pulp.
●
Clean using a soft brush.
●
Check the filter regularly for signs of damage. Do
not use if the filter is damaged. Refer to “service
and customer care”.
6
all other parts
●
Wash by hand, then dry.
●
Alternatively they are dishwasher safe and can be washed
on the top rack of your dishwasher. Avoid placing items on
the bottom rack directly over the heating element. A short
low temperature (Maximum 50°C) programme is
recommended.
service & customer care
●
If the cord is damaged it must, for safety reasons, be
replaced by KENWOOD or an authorised KENWOOD
repairer.
●
If you experience any problems with the
operation of the processor, before calling for
assistance refer to the troubleshooting guide.
If you need help with:
●
using your appliance or
●
servicing or repairs
●
Contact the shop where you purchased your appliance.
●
Designed and engineered by Kenwood in the UK.
●
Made in China.
IMPORTANT INFORMATION FOR CORRECT
DISPOSAL OF THE PRODUCT IN ACCORDANCE
WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed
of as urban waste.
It must be taken to a special local authority differentiated waste
collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health deriving
from inappropriate disposal and enables the constituent
materials to be recovered to obtain significant savings in energy
and resources. As a reminder of the need to dispose of
household appliances separately, the product is marked with a
crossed-out wheeled dustbin.
7
item suitable for
dishwashing
main bowl, lid, pusher ✔
knife blades, dough tool ✔
whisk beaters ✔
Do not immerse the drive head in water
detachable drive shaft ✔
discs ✔
citrus juicer ✔
centrifugal juicer ✔
mini bowl and knife ✔
liquidiser goblet, lid, filler cap ✔
mill jar ✔
blade unit and seal for liquidiser and mini ✘
chopper/mill
spatula ✔
storage carousel ✔
8
Problem Cause Solution
The processor will not operate No power/indicator light not lit. Check processor is plugged in
Bowl not fitted to power unit correctly. Check bowl is located correctly and the
handle is situated towards the right hand side.
Bowl lid not locked on correctly. Check that the lid interlock is located correctly
into the handle area.
The processor will not work if the
bowl and lid are fitted incorrectly.
If none of the above check the fuse/circuit
breaker in your home.
Liquidiser/mini chopper/mill Liquidiser/mini chopper/mill not locked The liquidiser/mini chopper/mill will not
will not operate on correctly. operate if fitted incorrectly to the interlock.
Liquidiser/mini chopper/mill not
Check blade unit is fully tightened into
assembled correctly.
the goblet.
Wrong base used. The mill base is not interchangeable
with the liquidiser goblet. The
processor will not operate if the
wrong base is fitted.
Check graphic is correct on base used.
Processor stops during Processor overloaded/maximum capacities Check maximum capacities stated in the
processing exceeded. recommended speed chart.
Lid unlocked. Check lid is locked correctly.
Liquidiser/mill leaking from Seal missing Check seal is fitted correctly and not
blade assembly base. Seal incorrectly fitted damaged. To obtain a replacement
Seal damaged. seal see “service & customer care”
Poor performance of Refer to hints in relevant “using the attachment” section. Check attachments are
tools/attachments. assembled correctly.
troubleshooting guide
Loading...