KENWOOD DPF-R6010, DPF-R3010 User Manual

CD PLAYER

CD/DPF-R SERIES

CD-206 CD-204 CD-203

DPF-R6010 DPF-R4010 DPF-R3010

INSTRUCTION MANUAL

KENWOOD CORPORATION

This instruction manual is used for six models. Model availability and features (functions) may differ depending on the country and sales area.

DTS disclaimer clause

When Playing DTS-encoded CDs, excessive noise will be exhibited from the analog stereo outputs. The consumer should take proper precautions when the analog stereo outputs of the CD player is connected to an amplification system. To enjoy DTS Digital Surround playback, an external 5.1 channel DTS Digital Surround decoder system must be connected to the digital output (S/ PDIF, ASE/EBU , or TosLink) of the CD player.

B60-3684-00 CH ( K,P,Y, M ,X ,T ) 99/12 11 10 9 8 7 6 5 4 3 2 1 98/12 11 10 9 8 7 6 5 4 3 2 1

I D

Introduction

Before applying pow er

Units are designed for operation as follows.

U.S.A. and Canada .........................................................AC 120 V only

Australia.......................................................................... AC 240 V only

* AC voltage selection

The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line volta ge. If not, it must be set to your voltage in accordance with the following direction.

Note: Our warranty does not cover damage caused by excessive line voltage due to improper setting of the AC voltage selector switch.

For the United Kingdom

Factory fitted moulded mains plug

CD-206 / 204 / 2 03/ DPF-R601 0 / R4010/ R3 0 10 (En

Caution : Read this section carefully to ensure safe operation.

U.K. and Europe .............................................................AC 230 V only

China ...............................................................................AC 220 V only

*Other countries .........................AC 110-120 / 220-240 V switchable

AC voltage selector switch

The illustration shows the CD-206/DPF-R6010.

LINE OUTPUT VARIABLE

AC220-240V

SYSTEM CONTROL

SL16 XS 8

DIGITAL OUTPUT COAXIAL

TEXT

OPTICAL

AC110-220V

AC220-2 40V

AC110-2 20V

M ov e swit ch le ver t o match your lin e volt age

with a small screwdriver or other pointed tool.

)

1. The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse.

2. The fuse cover must be refitted when replacing the fuse in the moulded plug.

3. Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:

Blue : Neutral Brown : Live

Do not connect those leads to the earth terminal of a three-pin plug.

Safety precautions

Caution : Read this section carefully to ensure safe operation.

WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAINOR MO ISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT

THE USER TO THE PRESENCE OF UNINSULATED “ DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EX CLAMATION POINT WITHIN AN EQUILATER AL TR IANGLE IS INTE NDED T O ALER T T HE USE R T O THE PR E SE NCE

OF IMPOR TANT OPE RAT ING AND MAINTE NANCE (S ER VIC ING) INST RUC TIONS IN THE LITE RAT URE ACC OMPANYING THE APPLIANCE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

REQUIREM ENT BY NEDERLAND GAZETTE

Batteries are supplied with this product. When they empty, you should not throw away. Instead, hand them in as small chemical waste.

The marking of products using lasers (Except for some areas)

CLASS 1

LASER PRODUCT

The marking is located on the rear panel and says that the component uses laser beams that have been classified as Cla ss 1. It means that the unit is utilizing laser beams that are of a weaker class. T here is no danger of hazardous radiation outside the unit.

Introduction

CD-206 / 204 / 2 03/ DPF-R601 0 / R4010/ R3 0 10 (En

Unpacking

Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Exa mine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future.

Keep this manual handy for future reference.

Special features

CD-TEXT support (CD-206/DPF-R6010 only)

Advanced technologies incorporated in pursuit of improved sound quality and stability (CD-206/DPF-R 6010 only)

Convenient features for dubbing CD onto tape

¶ The text information (disc title, track titles, names of the artists, songwriters, composers,

etc.) recorded o n the CDs can be easily called and displayed in alphanumeric s. (Some words and text may not be displayed.)

¶ D.R.I.V.E. (Dynamic Resolution Intensive Vector Enhancem e nt) IC is built in for drastic

reduct io n o f dist o rtion at small signal level.

¶ Normal EDIT: E dit function for rearra nging tracks according to the tape length so that no

music i s in terrupted in the middle.

¶ M ULTI EDIT: Several CDs can be edited and recorded on 1 tape. (Except f or CD-206/

DPF-R6010) ¡

¶ Auto space function. ^

)

Easy operation functions

¶ Ea sy operation functions allow systematic operation with other KENWOOD components

connected through the system control connection. 5

Accessories

Audio cord ............... (1) System control cord ...........(1)

Remote control unit ..............(1) Batteries (R6/AA)................. (2)

(Except for CD-203/DPF-R3010) (Except for CD-203/DPF-R3010)

RC-P0601

REMOTE CONTROL UNIT

Caution: Read the pages marked carefully to ensure safe operat ion.

AC plug adaptor .............. (1)

Use to adapt the plug on the power cord

to the shape of the wall outlet.

(Accessory only for regions where use is

necessary.)

Introduction..................................................................... 2

Before applying power................................................... 2

Safety precautions ......................................................... 2

Special features........................................................... 3

System connections....................................................... 4

Controls and indicators.................................................. 6

Operation of remote control unit ................................. 8

Preparing to play tracks................................................. 9

Normal play (TRACK mode) ........................................ 10

Searching for tracks by title (TITLE SEARCH)........... 12

Downloaded from:

Displays...........................................................................13

Programmed play (PGM mode) ................................... 14

Playback in random order (Random playback) ..........1 7

Repeated playback ........................................................ 18

Editing............................................................................. 20

Normal EDIT................................................................20

MULTI EDIT .................................................................21

Timer operations ........................................................... 23

Maintenance...................................................................24

In case of difficulty ........................................................ 25

Specifications................................................................. 26

System connections

Caution:

Do not plug in t he pow er lead until all connections are completed.

Make connections as shown below. When connecting the related sys tem components, refer also to the instruction manuals of the related components.

SL 16/XS8 switch 5

CD-206/DPF-R6010 :

LINE OUTPUT

To wall AC outlet

AC11 0-22 0V AC220 -24 0V

VARI ABLE

SYSTEM CONTROL

SL16 X S 8

DIGITAL OUTPUT

COAXIAL

TEXT

75Ω coaxial cable with RCA PIN. (Commerciallyavailable)

SYSTEM

CONTROL

OPTICAL

CD-206 / 204 / 2 03/ DPF-R601 0 / R4010/ R3 0 10 (En

M alfunction of microcomputer

If operation is not possible or erroneous display a ppears even though

all connections have been m ade properly, reset them icroco m put e r

referring to “ In case of difficulty” .

(COAXIAL) DIGITAL INPUT

(OPTICAL)

Remove the protection cap when using the DIGITAL OUTPUT (OPTICAL) jack

Commercially-available optical fiber cable

DIGITAL

INPUT

COAXIAL

OPTICAL

∞

Digital component (MD, DAT, etc.)

Digital amplifier (or ordinary amplifier, receiver, etc.)

)

System control cord

CD-204/203/ DPF-R4010/R3010 :

To wall AC outlet

AC 11 0-120 V 2 3 AC 2 20-24 0V



SYSTEM CONTROL



LINE OUTPUT



SL16 XS 8

Audio cord

SL 16/XS8 switch

Connection to digital amplifier or M D (CD-206/DPF-R6010 only)

Connec t the DIGITAL OUTPUT (OPTICAL or COAXIAL) jac k to the digital input jack of the amplifier, DAT recorder, MD recorder, etc., using an optical fiber cable or coaxial cable which are commercially available in audio stores.

÷ When using an optical fiber cable to connect this unit to a digital

amplif ier, insert the pl ug straight into t he jack unt il a snap sound is heard.

÷ Be careful not to b en d , co il, o r bu n d le the optical fiber cable. ÷ Optical fiber cables ava ila ble on the market may not always be able to

be used wit h t his player. If your cord cannot be us ed w it h t his u nit, consult the store from which you pu r c h ased the cord or your n earest dealer.

Optical fiber cable

Notes

Downloaded from:

1. Connect all cords firmly. If connections are loose there could be loss of sound or noise produced.

2. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging/unplugging connection cords without removal of the power cord can cause malfunctions or damage to the unit.

OTUUPT 1-d2B

System connections

SYSTEM CONTROL CONNECTIONS

Connec ting sys tem control cords after connec ting a KE NWOOD audio component system lets you take advantage of convenient system control operations. There are two KENWOOD system control modes. Make connections acc ording to the groups of terminal symbols shown below.

[XS 8] Mode : lets you combine F , f , and ƒ terminals [SL16] Mode : for

This unit is compatible with both [XS8] and [SL16] modes. Select the mode acc ording to the connec ted components. 4

SL16 XS 8

÷ Do this operation after completing all connections.

(Ensure that the unit is set to STANDBY mode.)

Notes

1. If yo u r am p li fier or receive r d o es n o t have a system control term in al, do not connect any system control cords to the system control terminals on the other components.

2. Do not con nect syst em c ont rol cords t o any com ponent s ot he r t han those specified by KENWOOD. It may cause a malfunction and damage your equipment.

3. Be sure the syst em c ont rol pl ugs are insert ed all t he way in t o t he sy st em control terminals.

terminals only

CD-206 / 204 / 2 03/ DPF-R601 0 / R4010/ R3 0 10 (En

SYSTEM

CONTROL

SYSTEM

CONTROL

SYSTEM

CONTROL

Amplifier or receiver

Cassette deck

)

This unit

SYSTEM CONTROL OPERATIONS

Remote Control

Lets you operate this unit with the system remote control unit supplied with the amplifier or receiver.

Automatic Operation (Except [XR] equipment)

Automatically switches the input selector on the amplifier or receiver when you start playback from this unit.

Synchronized Recording (Except [XR] equipment)

Lets you synchronize recording with the start of playback when recording from a CD. Also, the simple CCRS operation enables great recordings from CDs. See the operating instructions supplied with your cassette deck for details.

Adjusting the output levels of the output jacks and he adphone output (Exc ept for CD-203/DPFR3010)

The OUTPUT level (U P/DOWN) keys of the remote control unit can adjust the out put levels from t he LINE/ OUT and PHONES jacks of the unit.

OUTPUT

DOWN UP

REMOTE CONTROL UNIT

RC-P0601

÷ It is not favora ble for the sound quality to decrease the output level from

this u nit t oo muc h. Use th ese keys f or coordination w it h ot her line levels.

÷ Adjust ing the headphone output level also changes t he LINE/OUT

level. Do not adjust the out put level f rom th is unit particularly during recording.

÷ Please note th at the sound output is at the maximum le v el whe n the

power is turned on.

To use the headphone (Except for CD-203/DPFR3010)

Connect a stereo headphone to the PHONES jack of the CD player. Adjust the sound volume using the rem ote control unit.

CD-206/DPF-R6010

CD-204/DPF-R4010

12_db

Output level

54321

109876

Controls and indicators

CD-206/DPF-R6010

CD-206 / 204 / 2 03/ DPF-R601 0 / R4010/ R301 0 (En)

Play indicator

•• •• •• •• •• •• •• •

Pause indicator

CD-204/203/DPF-R4010/R3010

EDIT indicator

RANDOM indicator

Program mode indicator

Play indicator Pause indicator

PGM

Disc No. indicators

FILE

RANDOM NORM AL

MULTI

EDIT

REPEAT indicator

DISC NO.

54321

Text information display

REPEAT TRACK NO.

(The displays given in this manual are approximations only. They may differ from what actually appears on the display.)

P.C. indicator

SINGLE TOTAL

88 88 88_:

TRACK NO. indicator

Time counter, Program No. (S INGLE, TOTAL)

ALL indicator

P.C.

ALL

Music calendar (1 ~ 20)

543210 109876 1514131211 2019181716

The illustration of the common parts is of CD-206/DPF-R6010.

Except for USA and Canada

CD-204/203 DPF-R4010/R3010

CHECK

-ON –STANDBY

POWER

-ON –STANDBY

COMPACT

DIGITAL AUDIO

MU LTIPLE CD

TEXT

D.R.I.V.E.

PLAYER DPF-R60 10

TEXT DISP.

P.MODE

CLEAR

ALL INFO.

TIME DISP.

REPEATRANDOM

DISPLAY

CD-204/203 DPF-R4010/R3010

DISC 1 DISC 2 DISC 3 DISC 4 DISC 5

4¢

1¡

DISC 1 DISC 2 DISC 3 DISC 4 DISC 5

EDIT

DISC SKIP

PHONES

&%#^ *

About the STANDBY mode

When the power cord of this unit is plugged into an AC outlet, a small amount of current is being supplied to the unit even when the ON/ST ANDBY switch is not d ep r es s ed (–). This is called the STANDBY mode.

Downloaded from:

The keys with the same name as those on the remote control unit operate the same way as the remote control unit.

Controls and indicators

CD-206 / 204 / 2 03/ DPF-R601 0 / R4010/ R301 0 (En)

1 ON/STANDBY (POWER /

Turns the unit ON/STANDBY.

) switch 9

2 P.MODE key $ 3 TEXT DISP. key (CD-206/DPF-R6010 only) #

Used to select the CD-TEXT information display.

CHECK key (CD-204/203/DPF-R4010/R3010 only) %

Used to check or change program contents.

4 ALL INFO. key

Used to display all text information on the CD.

CLEAR key

Used to clear the program.

Remote control light sensor (CD-206/204/DPF-R6010/

(CD-206/DPF-R6010 only)

(CD-204/203/DPF-R4010/R3010 only)

R4010 only) 8

6 Skip keys (4,¢) !

Press to skip to the beginning of another track.

7 Disc selector keys (DISC1 – DISC5) / Indicator (CD-206/

DPF-R6010

Press to select the disc to be played.

only)

8 DISC SKIP key 9

Press to rotate the disc tray or to select the disc.

9 Open/Close key (0) 9

Opens and closes the disc tray.

0 RANDOM key &

Press to play the tracks in a random order.

! REPEAT key *

Press to play the tracks repeatedly.

@ TIME DISP. key ^

Press to switch the time indication mode.

# Disc tray 9

Load the disc to be played back.

$ Search keys (1,¡) !

Fast forwards or fast reverses the track.

% EDIT mode key )

Press to select the edit mode.

^ STOP key (7) 0 & PHONES jack (CD-206/204/ DPF-R6010/R4010 only)5

Use to connect (optional) headphones.

* PLAY/PAUSE key (6) 0

Each time the key is pressed, playback and pause switch each other.

Downloaded from:

Operation of remote control unit

The illustration shows the RC-P0601.

The keys with the same name as those on the main unit operate the same way a s on the main unit. The keys marked * are provided only on the remote control unit.

(Except for CD-203/DPF-R3010)

CD-206 / 204 / 2 03/ DPF-R601 0 / R4010/ R301 0 (En)

DISC SELECTOR

TEXT

DISPLAY

0 +10

TITLE

OUTPUT

REMOTE CONTROL UNIT

RC-P06 01

DISC SKIP

¢

¡

RANDOM

REPEAT

P.M ODE

TIME

DISPLAY

EDIT 7 8

CHECK

CLEAR ALL INFO.

ALL TEXT

DOWN UP

Loading batteries

1 Program-related and other keys

RANDOM key &

REPEAT key * P.MODE key $

TIME DISPLAY key ^ EDIT key )

* CHECK key (CD-206/DPF-R6010

only) %™

* CLEAR key (CD-206/DPF-R6010

only) ^™

2 Selector keys relating to text infor-

mation

* ALL TEXT SEARCH key 9

TEXT DISPLAY key # ALL INFO. key #

* TITLE SEARCH key @

CD-206/DPF-R6010 : M odel:RC-P0601 Infrared ray system

(

CD-206/DPF-R6010 only)

CD-204/DPF-R4010 : M odel:RC-P0504 Infrared ray system

* 3 OUTPUT (DOWN, UP) key 5

4 DISC SELECTOR keys 0

1 ~

))

5 DISC SKIP key

*6 Numeric keys (

7 Basic function keys

Stop key (7) 0 Play/Pause key (6) 0 Skip (4,¢) keys ! Search keys (1,¡) !

1 Remove t he cover. 2 Insert batteries. 3 Close the cover.

÷ Insert two AA-size (R6) batteries as

indicated by the polarity marking.

Operation

After plugging in the power cord, press the ON/ST ANDBY ( P OWER/

) switch of the main unit to turn the unit ON. When the unit is

turned ON, press the key of the function to be operated.

÷ When pressing more than one remote control key successively, press

the keys securely by leaving an interva l of 1 second or more between keys.

Remot e co n trol light s e n s or

30°6m30°

REMOTE CONTROL UNIT

RC-P0601

Operating range (Approx.)

1. The supplied batteries are intended for use in operation checks. Therefore, their lives may be shorter than ordinary batteries.

2. When the remote-controllable distance gets shorter than before, replace both batteries with new ones.

Notes

3. Malfunction may occur if direct sunlight or the light of a high-frequency lighting fluorescent lamp enters the remote control light sensor. In such a case, change the system installation position to prevent the malfunction.

IDCSRAEIDGN

1D:CDETTX

«

Preparing to Play Tracks

109876

54321

TRACK NO.

01 0 00:1

SINGLE TOTAL

DISC NO.

CD-206 / 204 / 2 03/ DPF-R601 0 / R4010/ R301 0 (En)

Preparation

Press the ON/ STANDBY (POWER / )key.

• Turn the unit ON.

POWER

-ON –STANDBY

Loading/unloading discs

Load/unload a disc.

Open the tray.

Place/remove a disc.

Label side

Disc tray

When loading or unloading other discs

Hereafter t he illustrat ion of t he comm on part s on the front panel is of CD-206/DPF-R6010.

REMOTE CONTROL UNIT

RC-P060 1

: Keys and controls used in the operation s d es c rib e d o n this page.

÷ Do not touch the played side of disc. ÷ Loading two disc s toget h er will cause malfunct io n in g. ÷ Place the disc properly a long the groove on the tray. (If the disc is not

placed horizontally, malfu n ction will result.)

÷ A single CD (8 cm disc ) can also be played. ÷ Ordinary CD single (8 cm) disc adapters sold in audio stores cannot be

used wit h this unit.

Close the tray.

DISC SKIP

÷ Whe n loading/unloading a disc w hile t he tray rot ates, a malf unction

might occur. Load/unload th e d isc wh en the t ray does no t rotat e .

CD-206/DPF-R6010

DISC 1 DISC 2 DISC 3 DISC 4 DISC 5

All DISC indicators "

" light regardless of how many discs are present.

CD-204/203/DPF-R4010/R3010

ALL TEXT SEARCH (CD-206/DPF-R6010 only)

All DISC indicators "

Remote control unit only

" light regardless of how many discs are present.

For most CD-TEXT discs, it is convenient to read the complete disc information into the CD player before playing the disc. This allows text information such as TITLE SEARCH, TEXT DISPLAY, ALL INFO., and other messages to be displayed faster.

Search in progress or reading information

After loading all the discs, operate in stop mode.

ALL TEXT

Blinks.

REMOTE CONTROL UNIT

RC-P0601

÷ The information read into the CD player is cleared when

the t ray is opened. Therefore, p erf orm th is operation again if the tray was opened.

When the disc is CD-TEXT

÷ Repeat the above pro ce du re s o that t h e co mplete disc info rmation is

read into the CD player.

÷ In the case of a non-C D-T EX T disc, the ”D1 : NO CD TEXT“ display will

appear for approx. 3 seconds.

+ 20 hidden pages

KENWOOD DPF-R6010, DPF-R3010 User Manual

Introduction

Before applying pow er

Safety precautions

Unpacking

Special features

Contents

System connections

Controls and indicators

Preparing to Play Tracks

Loading/unloading discs