How it Works
Kenwood
Loading...
CV-301
User Manual
56 pgs1.36 Mb0
Service manual
22 pgs6.96 Mb0
User Manual [it]
64 pgs15.04 Mb0
User Manual [it]
64 pgs15.04 Mb0
Table of contents
Loading...

Kenwood C-V301, C-V351 User Manual

AV CONTROL CENTER
C-V351 C-V301
INSTRUCTION MANUAL
KENWOOD CORPORATION
This manual contains instructions for two models. Model availability and features (functions) may differ depending on country and sales area.
B60-4349-00
EN

Before applying power

Units are designed for operation as follows.
Caution : Read this page carefully to ensure safe operation.
Europe and U.K. .............................................. AC 230 V only
For the United Kingdom
Factory fitted moulded mains plug
1. The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse.
2. The fuse cover must be refitted when replacing the fuse in the moulded plug.
3. Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.
IMPORTANT: The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral Brown: Live
Do not connect those leads to the earth terminal of a three-pin plug.

Safety precautions

C-V351/C-V301 (EN)
WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI-
ANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS IN­TENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALI­FIED SERVICE PERSONNEL.

Unpacking

Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future.

Accessories

FM indoor antenna (1) AM loop antenna (1)
Loop antenna stand (1)
Batteries(R6/AA) (4) (C-V351)
Graphical Remote Control unit (1) (C-V351)
Input
Main Menu
Return
Setup
C D
Sat.
DVD/6ch Input
Sound Speaker
ENTER
Source
TapeA
LD
Tuner
CD
Tape1
Confirm
Set Up
VOLUME
VCR2
TapeB
VCR1TVSat.Cable
Tape1
VCR1
L D
Cable
VCR2
T V
MUTE
Reset
ON/STANDBY
(Optional with the C-V301)
Batteries(R6/AA) (2) (C-V301)
Remote control unit (1) (C-V301)
Before applying power
C-V351/C-V301 (EN)

Contents

Before applying power.............................................................................................................................................................................................. 2
Contents ........................................................................................................................................................................................................................ 3
Special features.......................................................................................................................................................................................................... 4
System connection ..................................................................................................................................................................................................... 5
Controls and indicators ............................................................................................................................................................................................ 9
Setup of the Graphical Remote Control (GRC) unit (For C-V351).................................................................................................................... 11
Remote control of components from the GRC (For C-V351)............................................................................................................................. 16
Remote control with the “RC”unit (For C-V301) ................................................................................................................................................. 20
Convenient functions ............................................................................................................................................................................................... 21
Playing music ........................................................................................................................................................................................................... 22
Sound adjustment functions.................................................................................................................................................................................. 23
Recording .................................................................................................................................................................................................................. 25
Broadcast reception ............................................................................................................................................................................................... 26
RDS (Radio Data System) ....................................................................................................................................................................................... 27
Ambience effects...................................................................................................................................................................................................... 34
Clock adjustment ...................................................................................................................................................................................................... 45
Timer operation......................................................................................................................................................................................................... 46
Set up code chart...................................................................................................................................................................................................... 50
In case of difficulty .................................................................................................................................................................................................. 54
Specifications ..................................................................................................................................................................................................... 56
Safety precautions ......................................................................................................................................... 2
Unpacking ........................................................................................................................................................... 2
Connection of audio components (CD player, MD recorder, cassette deck, power amplifier) ........................ 5
Connection of video components (LD player, VCR, DVD) .................................................................................. 6
About the system control connections .............................................................................................................. 7
Connection of flat-cable connector ................................................................................................................... 7
Connection of antenna ....................................................................................................................................... 8
Controls and indicators(Optional with the C-V301)......................................................................................... 11
Setting up the GRC according to your AV CONTROL CENTER (Model Type Setup) ....................................... 12
Setting up the GRC according to the option components (Set Up) ...................................................................... 13
Setting up the GRC according to other components (Set Up)......................................................................... 15
Controlling the AV CONTROL CENTER............................................................................................................. 16
Controlling the components connected through system control cords .......................................................... 17
Names and functions of the keys .................................................................................................................... 20
One-touch operation and easy operation features ......................................................................................... 21
Receiving broadcast station............................................................................................................................. 26
Functions of RDS .............................................................................................................................................. 27
DISPLAY key ..................................................................................................................................................... 27
Storing RDS stations automatically in preset memory (AUTO MEMORY) ..................................................... 28
Receiving a preset RDS station ....................................................................................................................... 28
Storing radio stations manually in preset memory ......................................................................................... 29
Receiving a preset station ............................................................................................................................... 29
Receiving all preset stations in order (P. CALL) ............................................................................................... 29
Searching for a desired program type (PTY search) ........................................................................................ 30
Reserving reception of desired kind of programme in advance (EON reservation) ....................................... 32
To cancel EON reservation ............................................................................................................................... 33
Sound modes .................................................................................................................................................... 34
Setup for surround play.................................................................................................................................... 36
Surround play ................................................................................................................................................... 38
Setup for surround play (while listening to music) ......................................................................................... 39
Setup of the surround effect parameters (DSP) .............................................................................................. 43
Displaying the Time.......................................................................................................................................... 45
Timer programming .......................................................................................................................................... 46
Activating the timer ......................................................................................................................................... 48
Sleep timer ....................................................................................................................................................... 49
VCR Set up codes ............................................................................................................................................. 50
TV Set up codes................................................................................................................................................ 51
TV Set up codes................................................................................................................................................ 52
LD Set up codes................................................................................................................................................ 52
Satellite Set up codes ...................................................................................................................................... 53
Cable Set up codes........................................................................................................................................... 53
Caution : Read the pages marked
carefully to ensure safe operation.
Special features Special features
True home theater sound
Dolby Pro Logic & Dolby 3 Stereo
This surround system reproduces theater-like surround sound from video software marked . The PRO LOGIC mode uses the built-in adaptive matrix circuit to steer the Left, Center, Right and Surround channel audio signals. The 3 STEREO mode will redirect the surround signal to the front left and right speakers when only the front and center speakers are used.
New DSP surround modes
The DSP (Digital Signal Processor) used for this AV CONTROL CENTER incorporates a variety of high quality adjustable sound fields, like "ARENA", "JAZZ CLUB"and "STADIUM", to add the “presence” associated with an arena, jazz club or stadium (etc.) to the original signal. It is compatible with almost any kind of program source.
Graphical Remote Control unit ”GRC”(Optional with the C-V301)
The GRC unit incorporates a large-screen LCD which displays key icons and parameters. The LCD also shows information on the operating modes of the main unit. To improve the operability, frequently used icons are located in the higher hierarchy in the LCD display and icons which are associated between each other are shown on the same screen. The GRC unit is a multi-function remote control unit which can be programmed to control AV components from other manufacturers than KENWOOD. In the case of C-V301, It is able to use Graphical Remote Control (GRC-151/Option).
C-V351/C-V301 (EN)
RDS (Radio Data System) tuner
This AV CONTROL CENTER is equipped with a RDS tuner that provides several convenient tuning functions: AUTO MEMORY, to automatically preset up to 40 RDS stations broadcasting different programs; station name display, to show you the name of the current broadcast station; and PTY search to let you tune stations by program type.
ONE TOUCH OPERATION
Simply pressing the play key of the CD player or cassettedeck turns the system on and starts playback.

How to use this manual

In this manual, the operating procedures are described on the left half of each page and the supplementary explanation, display information and other notes on each step are described on the right half.
(Example of instructions in this manual)
Operating procedure steps (Left half)
Remote control unit to be used
Step No.
Select the DSP surround mode.
1
RC
Select DSP.
DSP
Graphical remote control key to be used
GRC
ENTER
DSP Mode
ENTER
Icon selection Press ENTER key.
Supplementary explanation (Right half)
Supplementary explanation for the remote control unit or Main unit operation(s)
RC/Main unit
Each press switches the indication.
1 ARENA 2 JAZZ CLUB 3 STADIUM
1 Selection cursor
2 Entry
Supplementary explanation for the graphical remote control operation
GRC
Sound DSP Mode
Arena
ENTER

System connection

C-V351/C-V301 (EN)
Connection of audio components
(CD player, MD recorder, cassette deck, power amplifier)
Make connection as shown below. When connecting the related system components, refer also to the instruction manuals of the related compo­nents. Do not plug in the power lead until all connections are
Malfunction of microcomputer
If operation is not possible or erroneous display appears even though all connections have been made properly, reset the microcomputer referring to “In case of difficulty”.
completed.
Analog disc turntable (with built-in equalizer amp)
ANTENNA
FM 75Ω
CONNECT WITH POWER AMPLIFIER
AM
PLAY
TAPE 2 (MONITOR)
REC
MONITOR OUT
PLAY
GND
SYSTEM
CONTROL
L
R
CD
IN
AUX TAPE 1/ MD
IN REC
VIDEO
LD
VCR
PLAY
DVD 6CH.INPUTDVD 6CH.INPUT
FRONT
SURROUND
CENTER
SUBWOOFER
AUDIO
/DVD
IN
REC
R
Shape of AC outlet
Europe
DVD
UNSWITCHED
CAUTION (For U.K.)
When using the AC out­lets equipped with this unit, be sure to consult your dealer for the cor­responding plug.
REC IN
System control cord
LINE OUTPUT
Connection cable
System
control cord
1
Power amplifier
*
*1 For the connection and operation proce-
dures of the power amplifier and speak­ers, refer to the instruction manual of the power amplifier (M-A300 or M-A100).
PLAY OUT
PLAY OUT
REC IN
CD player
2
Graphic equalizer
*
or Cassette deck 2
MD recorder or Cassette deck 1
The connected components shown here are given as examples because the available models vary depending on marketing areas.
Also connect the system control cords when the KENWOOD Audio Component System “SERIES 21” is connected.
*2Do not connect system control cord to the cassette
deck connected to the TAPE 2 (MONITOR) jacks.
CAUTION
Be sure to adhere followings. Or proper ventilation will be blocked causing damage or fire hazard.
÷ Install the R-SE7 on the top of the system. ÷ Do not place any objects impairing heat radiation onto the
÷ Leave a space around the unit (from the largest outside di-
To wall AC outlet
top of unit.
mension including projection) equal or greater than, shown below.
Top panel : 50 cm Side panel : 10 cm Back panel : 10 cm
System connection
C-V351/C-V301 (EN)
Connection of video components
Monitor TV
ANTENA
FM 75Ω
CONNECT WITH POWER AMPLIFIER
Video IN
GND
AM
SYSTEM
CONTROL
CD
L
R
IN
LD player
AUX TAPE 1/ MD
PLAY
IN REC
Video OUT
TAPE 2 (MONITOR)
REC
MONITOR OUT
PLAY
LD
/DVD
IN REC
Audio OUT
VIDEO
VCR
PLAY
DVD 6CH.INPUTDVD 6CH.INPUT
FRONT
(LD player, VCR, DVD)
CENTER
SUBWOOFER
SURROUND
AUDIO
UNSWITCHED
VCR
Audio IN
Audio OUT
Video IN
Video OUT
To wall AC outlet
Video OUT
Audio CENTER OUT/ SUBWOOFER OUT
Audio SURROUND OUT
Audio FRONT OUT
DVD
The connected components are given as examples because the avail­able models vary depending on marketing areas.
System connection
C-V351/C-V301 (EN)

About the system control connections

When this unit is connected to KENWOOD audio component system “SERIES 21”, also connect them through the system control cords to allow system-control operations between components.
Connection example
AV CONTROL CENTER
POWER AMPLIFIER
GRAPHIC EQUALIZER
CASSETTE DECK
SYSTEM
CONTROL
SYSTEM
CONTROL
SYSTEM
CONTROL
System control cord
System control cord
The SERIES 21 components which can be system-connected with this unit include the LD player, MD recorder, and DVD player.
NotesNotes
Notes
1. Do not connect the SERIES 21 components to other system components using system control cords.
2. Do not connect system control cords to any components other than those specified by KENWOOD. It may cause a malfunction and damage your equipment.
3. Be sure the system control plugs are in­serted all the way in to the system control terminals.
SYSTEM
CONTROL
System control cord
CD PLAYER
About the system control operations
(Available operations when SERIES 21 components are connected through system control cords)
Remote Control
Lets you operate source components with the system remote supplied with this unit.
Automatic Operation
When you start playback from a source component, the input selector on this unit switches to that component automatically. (Except TAPE 2)
Synchronized Recording
Lets you synchronize recording with the start of playback when recording from CD or LD.

Connection of flat-cable connector

Inserting the connector
Push in the connector straight into the socket until it clicks to indicate the locking.
Removing the connector
Push and hold the two ends of the connector, and pull it straight outward.
NotesNotes
Notes
1. Connect all cords firmly. If connections are loose, there could be loss of sound or noise produced.
2. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging / unplugging connection cords without removal of the power cord can cause malfunctions or damage to the unit.
3. Do not connect up a power source which is larger than that indicated on the socket at the rear of the unit.
4. If the system control cords or audio cords are not connected properly, the remote control or automatic operation between system components will not work properly.

Connection of antenna

Connection method to each antenna terminal
1 Push lever. 2 Insert cord. 3 Return lever.
AM loop antenna connection
The supplied antenna is for indoor use. Place it as far as possible from the main system, TV set, speaker cords, and power cord, and set it to a direction which provides the best reception.
System connection
C-V351/C-V301 (EN)
AM
ANTENA
FM 75Ω
GND
ANTENNA
FM 75Ω
AM
GND
FM indoor antenna connection
The accessory antenna is for temporary indoor use only. For stable signal reception we recommend using an outdoor antenna. Remove the indoor antenna if you connect one outdoors.
AM
ANTENA
FM 75Ω
GND
FM outdoor antenna connection
Lead the 75 Ω coaxial cable connected to the FM outdoor antenna into the room and connect it to the FM 75 Ω terminal.
Use the commercially available antenna adaptor.
ANTENNA
FM 75Ω
GND
AM
AM
ANTENA
FM 75Ω
GND

Controls and indicators

C-V351/C-V301 (EN)
RDS indicators (RDS, TP, TA, EON, PTY, NEWS, INFO.)
MEMORY indicator
RDS
INFO.
MEMO
NEWS
EON
TATP
1
PTY TIMER
ON/STANDBY
PHONES
1
TIMER indicators
2
2
INPUT TAPE 2
FM
MW
LW
Broadcast band indicators
3
(MONITOR)
TIMER
TIMER MODE
Frequency display, input selector display, preset channel display, surround mode display
4
SET
CLOCK
S.DIRECT
DISPLAY
RDS PTY
TA/NEWS/INFO.
AV CONTROL CERTER KC-2
Display
STEREO
A.MEMO
Decibel indicator
Delay time indicator
Receiving frequency unit indicators
765
8
DSP
AUTO BAND
MODE
dB
ms
kHz
MHz
DSP indicator
9
MULTI.CONTROL
LEVEL
PTY SELECT
TUNING
PRO LOGIC indicator
PRO LOGICPRO LOGIC
3 STEREO
DSPDSP
3 STEREO indicator
AUTO tuning mode/AUTO stereo
reception indicator TAPE 2 indicator
TAPE 2
SOURCE
DIRECT
SLEEP
SLEEP TIMER indicator
SOURCE DIRECT indicator
0
VOLUME CONTROL
OPEN/CLOSE
DOWN
STEREO indicator
AUTO
STEREO
TUNED
MUTE
TUNED indicator
MUTE indicator
UP
!
@
#
$^%
&
The keys which have the same names as the controls on the remote control unit provide the same functions as them.
1
(ON/STANDBY) key
Press to switch between ON and STANDBY.
2 Remote sensor 3 TIMER SET key
Press to set the timer function.
4 CLOCK key
Press to set the clock.
5 STEREO key 6 DSP key 7 DOLBY key 8 MODE key
Press to switch various setting modes.
9 MULTI.CONTROL key
Press to select various setting modes.
0 GRC transmitter
Outputs the signals transmitted to the Graphical Remote Control.
! PHONES jack
For use in headphones listening.
@ INPUT SELECTOR key
Press to select the input.
# TAPE 2 (MONITOR) key
For use in monitoring of recording, etc.
$ TIMER MODE key
Press to switch the timer modes.
% S.DIRECT key
Press to switch the Source Direct function which allows to reproduce the source with a better quality.
^ RDS DISPLAY key
Press to switch the RDS display.
& RDS PTY key
For use during reception of RDS broadcast­ing.
* RDS TA/NEWS/INFO. key
For use during reception of RDS broadcasting.
( A.MEMO key
Press when using the auto memory func­tion.
) AUTO key
Press to select the tuning mode. The auto tuning or manual tuning mode can be selected. The input selection display of a source can be switched to another by pressing and holding the AUTO key for more than 2 seconds.
(¡ ™)£¢
*
¡ BAND key
Press to switch the broadcasting band.
™ TUNING key ( , )
Press to select the radio station to be re­ceived. These keys are also used in the clock adjust­ment and timer operations.
£ OPEN/CLOSE key ¢ VOLUME CONTROL knob
0
Standby mode
While the standby indicator of the unit is lit, a small amount of current is flowing into the unit’s internal circuitry to back up the memory. This condition is referred to as the standby mode of the unit. While the unit is in the standby mode, it can be turned ON from the remote control unit. With this unit, standby mode is indicated by means of the display panel. The system is in standby mode while the clock display is shown.
10
Opening/closing the door
OPEN/CLOSE
Controls and indicators
C-V351/C-V301 (EN)
Note
Note
When opening or closing the door, be careful not to catch your finger in the door. Otherwise there is a risk of injury.
Changing the input selection display (AUTO key)
*1: To change the TAPE 1 display to MD display
1 Select “TAPE 1” with the INPUT SELECTOR . 2 Press and hold the AUTO key for more than 2 seconds, until
“MD” is displayed.
Each press switches the indication.
1 TAPE1 2 MD
*2: To change the LD display to the DVD display
1 Select “LD” with the INPUT SELECTOR . 2 Press and hold the AUTO key for more than 2 seconds, until
“DVD” is displayed.
Each press switches the indication.
To make the system control operation, the input selection display should be switched according to the actually connected compo­nents. About the system control connections
7
1 LD 2 DVD
Switching the display mode (DISPLAY key)
Use the following procedure to change the display mode.
Press the DISPLAY key (RC and GRC only). Select "Display" from "Main Menu 2" when using the GRC.
Each press switches the indication.
1 INPUT SELECTOR
display
2 DOLBY/DSP/
STEREO display
3 Time
display
÷ The time display is displayed for only 5 seconds, after which the INPUT
SELECTOR display appears automatically.
÷ The display of 2 is not shown during SOURCE DIRECT and 6ch INPUT
operations.
÷ With the C-V301, the display does not change while the INPUT
SELECTOR is set for the LD input.
For C-V351

Setup of the Graphical Remote Control (GRC) unit (For C-V351)

C-V351/C-V301 (EN)

Controls and indicators

(Optional with the C-V301)
The Graphical Remote Control (GRC) unit provided with the AV CONTROL CENTER can also control KENWOOD cassette decks, CD player, DVD player and LD player which are connected to it through system control cords. For details of the controllable functions, refer to the instruction manuals of these components.
Model:GRC-151
Infrared system
Note
Note
Perform “Model Type Setup” of the GRC before using it. The following menu screen appears immediately after the batteries have been loaded for the first time.
Type Setu
p
Model 4 Model 5 Model 6
Model
Model 1 Model 2 Model 3
1
)
¡ ™
2
Main
Menu
Confirm
Return
Setup
C D Sat.
DVD
Sound
TapeB
TV
VCR2
TapeA
Tuner
CD
DVD
L D
T V
Tape1
LD
MD
Tape1
Cable
VCR1
Sat.Cable
VCR1 VCR2
Set Up
ENTER
M D
Reset
ON/STANDBY
MUTE
VOLUME
¢
∞
§
•
34567890!@#$%^&*(
ª
£
Segment screen
1 Segment screen
This area displays the fixed icons.
2 Return icon
Select to return to the previous display.
3 Main Menu icon
Select to change the input source or select Main Menu 2.
4 Confirm icon
Select to confirm a setting, etc.
5 Sound icon
Select to control the sound-related functions.
6 DVD icon
Select to control the DVD player.
7 CD icon
Select to control the CD player.
8 MD icon
Select to control the MD recorder.
9 Tuner icon
Select to control the tuner.
0 LD icon
Select to control the LD player.
! Tape A icon
Select to control cassette deck A.
@ Tape 1 icon
Select to control cassette deck 1.
# Tape B icon
Select to control cassette deck B.
$ Cable TV icon
Select to control the cable TV.
% TV icon
Select to control the TV.
^ VCR 1 icon
Select to control VCR 1.
& Satellite Tuner icon
Select to control the satellite tuner.
* VCR 2 icon
Select to control VCR 2.
( Set Up icon
Select to make setup operations.
÷ The input source can be selected
using icon 3.
÷ Icons 6 to * are used to select the
component to be controlled.
The displayed icons are variable depending on the “Model Type Setup” for matching the specifications with the AV CONTROL CENTER which uses the GRC unit and “Setup” for matching the specifications with connected source compo­nent.
Menu screen
) Menu screen
This area displays the control key icons and level information.
¡ Mode display
The above illustration indicates the Setup mode.
™ CD icon
Select to set up the CD player.
£ Reset icon
Select to return to the “Model Type Setup” menu screen.
Operation keys
¢ Joystick key
For use in selecting icons. The joystick moves in 8 direc­tions.
∞ ENTER key
Press to enter a selection.
§ VOLUME (UP) control key
Press to increase the volume level.
VOLUME (DOWN) control
key
Press to decrease the volume level.
• MUTE key
Press to mute sound temporarily.
ª (ON/STANDBY) key
Press to switch the AV CONTROL CENTER and the components connected to it through system control cords between ON and STANDBY.
11
Approximate operating range
Remote sensor
30°5m30°
GRC or RC Infrared ray system
Infrared remote control
1. The supplied batteries are intended for use in operation check.
Notes
Notes
Therefore, their lives may be shorter than ordinary batteries.
2. When the remote-controllable distance gets shorter than before, replace all four batteries with new ones.
3. Malfunction may occur if direct sunlight or the light of a high­frequency lighting fluorescent lamp enters the remote sen­sor. In such a case, change the system installation position to prevent the malfunction.
4. The GRC display may show erroneous information when the GRC unit is operated from outside the specified range.
Model
Type Setu
p
Model 6
Model 5
Model 4
Model 3
Model 2
Model 1
For C-V351
Setup of the Graphical Remote Control (GRC) unit
C-V351/C-V301 (EN)
Setting up the GRC according to your AV CONTROL CENTER
12
Perform the following procedure after inserting batteries for the first time and every time after changing them.
Model
Preparation
Model Type Setup (GRC setup procedure)
Loading batteries
1
1 Remove the cover. 2 Insert batteries. 3 Close the cover.
1
2
÷ Press the (ON/STANDBY) key
of the main unit to the ON mode.
3
Main operation menu
Caution in battery replacement
÷ Insert four AA-size (R6/AA) batteries
as indicated by the polarity marking.
÷ To maintain the memory of the settings you
made before, complete the battery replace­ment operation within 30 seconds.
÷ The procedure on the left should also be per-
formed when resetting the GRC (as a measure against its malfunction). However, in this case, wait for about five minutes after removing the batteries and before re-inserting them.
(Model Type Setup)
p
Type Setu
Model 4
Model 1
Model 5
Model 2
Model 6
Model 3
ENTER
VOLUME
MUTE
ON/STANDBY
Check the display.
2
The “Model Type Setup” screen ap­pears.
Select "Model 2."
3
Move the cursor.
It can be moved in 8 directions depend­ing on how you press the joystick key.
ENTER
The icon on which the cursor is moved blinks in reverse video.
Enter the selection.
4
Press the ENTER key.
ENTER
AV CONTROL CENTER Model
C-V301 ............................................... Model 2
C-V351 ............................................... Model 2
GRC “Model Type Setup” icon
To reset GRC setting
1 Select Set Up.
2 Press the ENTER key. 3 Select Reset.
4 Press the ENTER key. 5 Perform the setup procedure from step ”2 Check the display”.
÷ The above operation clears all of the previously made settings and
resets the unit to the initial condition.
Set Up
ENTER
Reset
ENTER
For C-V351
ON/STANDBY
MUTE
VOLUME
ENTER
Setup
DVD
Sound
C D Sat.
Tape1 Cable
Reset
VCR1 VCR2
L D
M D
T V
Confirm
Set Up
Return
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1
TV
Sat.Cable
MD
Main Menu
DVD
Setup of the Graphical Remote Control (GRC) unit
C-V351/C-V301 (EN)
Setting up the GRC according to the option components
(Set Up)
The following procedures prepare the GRC for operating the components connected through system control cords. Make sure that these components are connected through system control cords. 7
÷ If you proceed to the following “Set Up” operations immediately after steps 1 to 4 of “Model Type
Setup (GRC setup procedure)” on page @, start operation with step “3 Select the CD icon” in the “Set Up CD” procedure.
Main operation menu
Set Up CD Set Up Tape 1 Set Up LD
Setup of GRC according to the CD player in use
1 Select the ”Set Up“ icon.
Set Up
2 Press the ”ENTER“ key to enter the
selection.
3 Select the ”CD“ icon.
4 Press the ”ENTER“ key to enter the
selection.
ENTER
C D
ENTER
Setup of GRC according to the cassette deck in use
1 Select the ”Set Up“ icon.
Set Up
2 Press the ”ENTER“ key to enter the
selection.
3 Select the ”Tape 1“ icon.
4 Press the ”ENTER“ key to enter the
selection.
ENTER
Tape1
ENTER
Setup of GRC according to the LD player in use
1 Select the ”Set Up“ icon.
Set Up
2 Press the ”ENTER“ key to enter the
selection.
3 Select the ”LD“ icon.
4 Press the ”ENTER“ key to enter the
selection.
ENTER
L D
ENTER
13
5 Select the ”Single“ icon.
Single
÷ Select “Single”, “Dual”, “Carrousel” or
“Changer” according to the connected CD player type.
6 Press the ”ENTER“ key to enter the
selection.
7 Select the ”Main Menu“ icon.
8 Press the ”ENTER“ key to enter the
selection.
÷ Icon
has completed.
ENTER
Main
Menu
ENTER
appears at the moment the setup
In the operations of the GRC (Graphical Remote Control unit), proceed to each step within 10 seconds after the previous step. The display disappears in 10 seconds.
5 Select the ”Dual“ icon.
Dual
÷ Select “Dual” or “Single” according to
the connected cassette deck type.
6 Press the ”ENTER“ key to enter the
selection.
7 Select the ”Main Menu“ icon.
8 Press the ”ENTER“ key to enter the
selection.
÷ Icons
moment the setup has completed.
ENTER
Main
Menu
ENTER
/ or icon appear at the
5 Select the ”System Control“ icon.
System Control
÷ Select “System Control” or “IR” ac-
cording to the connected LD player type.
6 Press the ”ENTER“ key to enter the
selection.
7 Select the ”Main Menu“ icon.
8 Press the ”ENTER“ key to enter the
selection.
÷ Icon
has completed.
ENTER
Main
Menu
ENTER
appears at the moment the setup
To resume GRC display, move the Joy­stick key in any directions.
14
ON/STANDBY
MUTE
VOLUME
ENTER
Setup
DVD
Sound
C D Sat.
Tape1 Cable
Reset
VCR1 VCR2
L D
M D
T V
Confirm
Set Up
Return
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1
TV
Sat.Cable
MD
Main Menu
DVD
Set Up MD Set Up DVD
For C-V351
Setup of the Graphical Remote Control (GRC) unit
C-V351/C-V301 (EN)
Main operation menu
Setup of GRC according to the MD recorder in use
1 Select the ”Set Up“ icon.
Set Up
2 Press the ”ENTER“ key to enter the
selection.
3 Select the ”MD“ icon.
4 Press the ”ENTER“ key to enter the
selection.
5 Select the ”System Control“ icon.
System Control
÷ Select “System Control” or “IR” ac-
cording to the connected MD recorder type.
6 Press the ”ENTER“ key to enter the
selection.
7 Select the ”Main Menu“ icon.
8 Press the ”ENTER“ key to enter the
selection.
ENTER
M D
ENTER
ENTER
Main
Menu
ENTER
Setup of GRC according to the DVD player in use
1 Select the ”Set Up“ icon.
Set Up
2 Press the ”ENTER“ key to enter the
selection.
3 Select the ”DVD“ icon.
4 Press the ”ENTER“ key to enter the
selection.
5 Select the ”Main Menu“ icon.
6 Press the ”ENTER“ key to enter the
selection.
ENTER
DVD
ENTER
Main
Menu
ENTER
÷ Icon
completed.
appears at the moment the setup has
÷ Icons
completed.
appear at the moment the setup has
For C-V351
ON/STANDBY
MUTE
VOLUME
ENTER
Setup
DVD
Sound
C D Sat.
Tape1 Cable
Reset
VCR1 VCR2
L D
M D
T V
Confirm
Set Up
Return
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1
TV
Sat.Cable
MD
Main Menu
DVD
Setup of the Graphical Remote Control (GRC) unit
C-V351/C-V301 (EN)
Setting up the GRC according to other components
(Set Up)
The GRC can also be used to remote control other compo­nents which are not connected through system control cords. To control another component, it is required to regis­ter the setup code corresponding to it beforehand. p
Main operation menu
Registering setup codes for VCR 1
Find the setup code of the component to be registered by referring to the Setup code chart in this manual.
1
Enter the setup code.
2
1 Select the ”Set Up“ icon.
2 Enter the selection
(by pressing the ”ENTER“ key).
3 Select the ”VCR 1“ icon.
Set Up
ENTER
VCR1
Check the operation of the component.
1 Display the operation screen of the component to be checked. 2 Turn on the component from the GRC and confirm the
actual component.
÷ If there is more than one setup code, input each code to see
which one turns the power on. That will be the correct code for your component.
15
4 Enter the selection
(by pressing the ”ENTER“ key).
ENTER
Although each setup code is designed to work with a number of different models, certain codes may not work
Note
Note
with some models. (Also, certain codes may only operate some of the functions available on a given model.) With some models, be sure to keep the ENTER key pressed for a while.
Use the numeric keys as shown below.
Entry examples:
431 .....4
400 .....4
ENTER
ENTER
3 )
ENTER
ENTER
1 )
5 Enter the setup code.
6 Select the ”Set“ icon.
Set
000
1 4 7 0
Set
2
3
5
6
8
9
431
7 Enter the selection
(by pressing the ”ENTER“ key).
ENTER
÷ When a code which is not shown in the setup code chart is entered,
the entered code disappears automatically.
Registering setup codes of other components
The procedure of steps 1 and 2-1 to 7 of “Registering setup code for VCR 1” also allows to register the compo­nents listed below to remote control them from the GRC.
Registering setup code for VCR 2
ENTER
ENTER
Registering setup code for TV Registering setup code for CABLE Registering setup code for SATELLITE Registering setup code for LD player (IR)
For C-V351
ON/STANDBY
MUTE
VOLUME
ENTER
Main Menu 1
C D
Tuner
Tape1 / MD
VCR AUX
Confirm
Set Up
Return
Input Source
Main Menu
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1TVSat.Cable
LD / DVD
6ch Input
Confirm
Set Up
Return
Main
Menu

Remote control of components from the GRC (For C-V351)

C-V351/C-V301 (EN)

Controlling the AV CONTROL CENTER

16
The operations required to remote control the AV CONTROL CENTER includes the INPUT SELECTOR selection, display mode selection, stereo selection and so on. The following procedures show how to remote control the basic operations of the GRC.
Main operation menu
Operation examples
Switching the INPUT SELEC-
(Selecting the CD input)
TOR
1 Select the ”Main Menu“ icon in the
fixed segment screen by operating the joystick.
1
Main
Menu
Confirm
Return
2 Press the ”ENTER“ key to enter the
selection.
ENTER ENTER
3 Select the ”CD“ icon with the joy-
stick.
Main Menu 1
C D
Tuner
VCR AUX
Tape1 / MD
LD / DVD
6ch Input
4 Press the ”ENTER“ key to enter the
selection.
ENTER
Set Up
Switching the display mode of the AV CONTROL CENTER
1 Select the ”Main Menu“ icon in the
fixed segment screen by operating the joystick.
1
Main Menu
Confirm
Return
2 Press the ”ENTER“ key to enter the
selection.
3 Select the ”Main Menu“ icon again.
3
Main Menu
Confirm
Return
4 Press the ”ENTER“ key to enter the
selection.
ENTER
Set Up
Set Up
Selecting the stereo mode
1 Select the ”Sound“ icon in the fixed
segment screen by operating the joy­stick.
1
2 Press the ”ENTER“ key to enter the
selection.
3 Select the ”STEREO“ icon with the
joystick.
Sound
PRO LOGIC 3 STEREO
STEREO
4 Press the ”ENTER“ key to enter the
selection.
ENTER
Source
Direct
3
ENTER
5 The input source is switched to ”CD“.
÷ Other input than CD can be selected in
step 3.
5 Select the ”Display“ icon.
Main Menu 2
Tape2 Monitor
Sleep
Display
6 Press the ”ENTER“ key to enter the
selection.
ENTER
7 Each press of the ”ENTER“ key
switches the display mode.
÷ It is also possible to select the Tape 2
Monitor or Sleep icon in step 5.
÷ It is also possible to select the Pro Logic,
3 STEREO or Source Direct icon in step
3.
For C-V351
ON/STANDBY
MUTE
VOLUME
ENTER
Main Menu 1
C D
Tuner
Tape1 / MD
VCR AUX
Confirm
Set Up
Return
Input Source
Main Menu
TapeA
TapeB
Tape1
LD
Tuner
CD
VCR2
VCR1TVSat.Cable
LD / DVD
6ch Input
Remote control of components from the GRC
C-V351/C-V301 (EN)

Controlling the components connected through system control cords

17
When a CD player, cassette deck and/or LD player are connected with the AV CONTROL CENTER through system control cords, their system control operations are possible from the GRC.
Preparations
Operating the tuner
1 Select the ”Tuner“ input.
2 Display the tuner operation
menu.
3 Select the icon to be operated.
4 Enter the selection
(by pressing the ”ENTER“ key).
÷ System control connection 7 ÷ Model Type Setup @ ÷ Setup of source components #
Main
Menu
ENTER
Tuner
ENTER
Tuner
ENTER
Tuner
100.00
fm MHz
Auto Band
RDS
ENTER
P.Call
01ch
Memory /
10key Pad
Main operation menu
÷ Any of the keys which can control the tuner can be selected.
Operating the CD player
1 Select the ”CD“ input.
2 Display the CD operation menu.
3 Select the icon to be operated.
4 Enter the selection
(by pressing the ”ENTER“ key).
CD
Mode
Main
Menu
ENTER
C D
ENTER
CD
ENTER
Track 01
ENTER
10key
Pad
÷ Any of the CD player operation keys can be selected. ÷ The menu display shown on the left is an example which appears with
a single CD player.
÷ For the operation of the CD player, also read the instruction manual of
the CD player.
Loading...
+ 39 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use