Kenmore 630.1390, 630.1391, Elite 630.1390 Series, Elite 630.1391 Series Installation Manual

Installation Guide

Instrucciones de Instalaci6n

instructions dlnstallation

English / Espafiol/Frangais

Models/Modelos/Mod_les: 630.1390% 630.1 391_

I<enmore Elite

@

COO w _sn6_o /_ G CO_J@J_'Ge ...... Ge

P/N 9000543976 Rev. A
Sears Brands Management Corporation

Haft:man Estates,
IL 60179 U.S.A.

www.kenmore.com

www.sears.com

Sears Canada Inc.
Toronto, Ontarlot Canada M5B 2B8

www.sears.ca

Dishwasher Safety ........................................................

Installation Requirements ..............................................

Materials needed .....................................................................

Tools needed .................................................................................

Materials supplied .......................................................................

Pre-install checklist .......................................................................

Drain requirements ......................................................................

Water supply requirements .......................................................

Electrical requirements ................................................................

Installation Instructions .................................................

To avoid possible injury or property damage, OBSERVE ALL
WARNINGS AND CAUTIONS. These instructions are intend-

ed for use by qualified installers only. In addition to these
instructions, the dishwasher shall be installed to meet all
electrical and plumbing codes and ordinances (both national
and local).

Avoiding General Hazards

Do not use the dishwasher until it is completely installed. When
opening the door on an uninstalled dishwasher, carefully open
the door while supporting the rear of the unit. Failure to follow
this warning can cause the dishwasher to tip over and result

in serious injury.

In some conditions, hydrogen gas can form in a hot water system
that has not been used for weeks. Hydrogen gas is explosive.
Before filling a dishwasher from a system that has been off for
weeks, run the water from a nearby faucet in a well ventilated
area until there is no sound or evidence of gas.

Temperatures required for soldering and sweating will damage
the dishwasher's base and water inlet valve. If plumbing lines
are to be soldered or sweated, keep the heat source at least
6 inches (152.4 mm) away from the dishwasher's base and

water inlet valve.

Make sure electrical work is properly installed. There should be
no loose electrical connections. Ensure all electrical connections

are properly made.

The customer has the responsibility of ensuring that the
dishwasher electrical installation is in compliance with all

national and local electrical codes and ordinances. The
dishwasher isdesigned for an electrical supply of 120V, 60 Hz,

AC, connected to a dishwasher-dedicated, properly grounded
electrical circuit with a fuse or breaker rated for 15 amps.
Electrical supply conductors shall be a minimum #14 AWG
copper only wire rated at 75°C (167°F) or higher.

This appliance must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on

the appliance. Do not use extension cords.

_ Avoiding Plumbing/Scalding Hazards
Do not perform any work on a charged hot water line. Serious

injury could result. Only qualified plumbers should perform
plumbing work. Do not attempt any work on the dishwasher
hot water supply plumbing until you are certain the hot water
supply is shut off.

Do not over tighten the 90 ° elbow. Doing so may damage the
water inlet valve and cause a water leak.

Removing any cover or pulling the dishwasher from the cabinet
can expose hot water connections, electrical power and sharp
edges or points. Handle with care. Always wear gloves and
safety glasses.

_Avoiding Electrical Shock/Fire Hazards
Do not allow the electrical and water supply lines to touch.

Separate channels are provided under the dishwasher.

Do not work on an energized circuit. Doing so could result
in serious injury or death. Only qualified electricians should
perform electrical work. Do not attempt any work on the
dishwasher electric supply circuit until you are certain the circuit
is de-energized.

Temperatures required for soldering and sweating will damage
the dishwasher's water inlet valve. If plumbing lines are to be
soldered or sweated, keep the heat source at least 6 inches
(152.4 mm) away from the dishwasher's water inlet valve.

Check local plumbing codes for approved plumbing procedures
and accessories. All plumbing should be done in accordance

with national and local codes.

These instructions depict an installation method for stainless
steel braided hose or PEX hot water supply lines, if using
copper tubing or other materlal for water supply, defer to a
licensed plumber for proper installation.

Readtheseinstallatloninstructionscompletelyand follow

them carefully. They will save you time and effort and help
to ensure safety and optimum dishwasher performance.

if the dishwasher is installed in a lacatlon that experiences
Freezing temperatures (e.g., in a hallday home), you must

drain all the water from the dishwasher's interior. Water
system ruptures that occur as a result of freezing are NOT

COVERED BY WARRANTY.

iMPORTANT

• The dishwasher drain hose must be installed with a portion
of it at least 20" (508mm) off the cabinet floor; otherwise
the dishwasher may not drain properly.

This dishwasher is intended for indoor residential use
only, and should not be used in commercial food service

establishments.

This dishwasher is designed to be enclosed on the top and
both sides by cabinetry.

NEW INSTALLATION - If the dishwasher isa new installation,
mast of the work must be done before the dishwasher is

moved into place.
REPLACEMENT - If the dishwasher is replacing another
dishwasher, check the existing dishwasher connections for
compatibility with the new dishwasher, and replace parts
as necessary.

• This appliance has been found to be in compliance with
CAN/CSA-C22.2 No. 167/UL 749. it is the responsibility

of the owner and the installer to determine if additional
requirements and standards apply in specific installations.

• Not for outdoor use.

OTHER iMPORTANT iNFORMATiON

inspect the Dishwasher

After unpacking the dishwasher and prior to installation,
thoroughly inspect the dishwasher for possible freight or
cosmetic damage. Report any damage immediately. Cosmetic
defects must be reported within 30 days of installation.
NOTE: Do not discard any bags or items that come with the
original package until after the entire installation has been
completed.

Electrical Supply Cable - Minimum #14 AWG
2 conductor, 1 ground, insulated copper
conductors rated 75°C (167°F) or higher.

Hot Water Supply Line - Minimum 3/8"
O.D. copper tubing, PEX, or metal braided
dishwasher supply line.

90 ° elbow with 3/8" N.P.T. male threads on
one leg, and sized to fit your water supply line
(copper tubing!compression fitting, or braided
hose) on the other leg.

Thread seal tape or other pipe sealant
compound to seal plumbing connections.

Shut-off valve and fittings appropriate
for hot water supply line (copper tubing/
compression fitting, or braided hose).

UL listed conduit connector or strain relief.

Hammer Hole Saw Safety Glasses Adjustable Wrench

Pliers Needle Nose Pliers Work C_loves Screwdrivers

Measure Tape Wire Strippers

Mounting Bracket Screws

Drill

Spring Clamp Screw Clamp

Level

i:

Drain Hose

Toe Panel Screws

o-Q

4

Junction Box Screw

Leg Leveler Screws

IMPORTANT!
Before you begin, you must read the safety instructions!

PRE-INSTALL CHECKLIST

[] Unpack unit. Retain packing material until successful

installation is complete.

[] Remove all packing material from inside the dishwasher.
[] Inspect parts to ensure you have all the necessary

materials.

[] Flush household hot water supply for at least two

minutes.

[]Measure the enclosure area.
[] Is the opening at least 34" (87 cm) high and 235/8"

(60-61 cm) wide?

[] Is the opening near enough to the sink for the water line

and drain hoses to access plumbing?

[] Is the drain hose being connected to the garbage

disposal, if so, is the knockout plug on the disposal
removed?

[] Will the unit be installed close enough to the sink so that

drain hose length does not exceed 92" (234 cm) and so
that a portion of the drain hose is raised at least 20"
(51 cm) above the floor?

[] Do the openings for electric cable, water line and drain

hose routing through cabinet fit as shown in the manual?

[] Are the openings sanded smooth if wood or covered by

a protective gasket if metal?

[] Check that the incoming hot water supply line

is connected to the water inlet connection on the
dishwasher and has a water pressure of 15-145 PSI

(1 -10 bar). Wash program cycle times are based on

120F.

[] If installing in a corner, will the dishwasher door clear

cabinet hardware?

[] Determine mounting method based on dishwasher

model and countertop type.

Avoid Scalding or Electrical Shock Hazard!

Make sure the water supply and electrical supply are shut

off before installation or service.

Note: Plumbing installations will vary - refer to local codes.
Drain hose included is 92" (234 cm) and can be extended to
a maximum of 150" (381 cm). Ensure a portion of the drain

hose is raised at least 20" (51 cm) above the floor.
Ensure that the dishwasher electrical installation is in compliance

with all national and local electrical codes and ordinances.

The dishwasher is designed for an electrical supply of 120V,

60 Hz, AC, connected to a dishwasher-dedicated, properly

grounded electrical circuit with a fuse or breaker rated for
Note: Plumbing installations will vary - refer to local codes. 15 amps. Electrica! supply conductors shall be a minimum #14
Always include a Loop in the Drain Hose for proper function AWG copper only wire rated at 75°C (167°F) or higher.

• Height of loop -[Min. 20"(51cm) - Max. 43"(109cm)]

• Length of Drain Hose included on Dishwasher 92" (233

cm)
When adding an extension to the Drain Hose the maximum
length for proper Dishwasher function is 168" (426 cm).

• A hot water supply line - Minimum 3/8" O.D. Copper
tubing, PEX, or metal braided dishwasher supply line.

• 120°F (49°C) water at dishwasher.

• Shut-off valve and fittings appropriate for hot wa-
ter supply line (copper tubing/compression fitting or

braided hose).

• 90 ° elbow with 3/8" N.P.T. male threads on one leg,
and sized to fit your water supply line (copper tubing/
compression fitting, or braided hose) on the other leg.