Kenmore 79641182310, 79641182311 Owner’s Manual

Use & Care Guide

Manual de Uso Y Cuidado

English / Espa_ol

Model/Modelo: 796.4118#31#

I<e

}# ]:,?C

',;3 00L)Z( '( OS " ,i_, ,':<; y(

; ] "<=" ..... " _"_" D;}[,;}_ ' • "........ ;_, AY} .:, I-[ 8VI(lO 81

QU_I_OFF_Q =CQ de

P/N MFL67737652 Sears Brands Management Corporation Hoffman Estates, IL60179 U.S.A.

www.kenmore.com www.sears.com

IC c

ca a

IMPORTANT SAFETY INSTRUCTIONS .............................. 3=5

GROUNDING REQUIREMENTS ............................................. 5

FEATURES AND BENEFITS

Key Parts and Components ................................................. 6

Included Accessories ........................................................ 6

Optional Accessories ........................................................ 6

iNSTALLATiON REQUIREMENTS

Key Dimensions and Specifications ................................... 7

Choose the Proper Location ............................................... 7

Flooring .................................................................................. 7

Clearances ............................................................................ 7

INSTALLATION INSTRUCTIONS

Unpacking and Removing Shipping Bolts ......................... 8

Connecting the Water Lines ................................................ 9

Connecting the Drain Hose ............................................... 10

Connect to the Power Supply ............................................. 10

Leveling the Washer ........................................................... 11

Installation of Non-Skid Pads (optional) .......................... 11

HOW TO USE

Control Panel Features ........................................................ 12

Operating the Washer ......................................................... 13

Cycle Guide .................................................................... 14-15

Sorting Wash Loads ............................................................ 16

About the Dispenser Drawer .............................................. 17

Detergent and Dispenser Use............................................. 18

Magnetic Door Hunger ..................................................... 18

Time and Status Display .................................................... 19

Cycle Modifier Buttons ....................................................... 20

Option Buttons ..................................................................... 21

Delay Start ........................................................................ 21

Extra Rinse ....................................................................... 21

Pre Wash ........................................................................... 21

Special Functions ................................................................ 22

Control Lock ..................................................................... 22

Clean Washer ................................................................. 22

Auto Soak ......................................................................... 22

CARE AND CLEANING

Regular Cleaning .......................................................... 23-24

Cleaning the Exterior ...................................................... 23

Care and Cleaning of the Interior ................................ 23

Clean Washer .................................................................. 23

Door Seal and Glass Cleaning ..................................... 23

Removing Mineral Buildup ............................................. 23

Storing the Washer ......................................................... 24

Cleaning the Dispenser .................................................. 24

Maintenance ................................................................. 25-26

Cleaning the Water Inlet Filters .................................... 25

Cleaning the Drain Pump Filter ..................................... 26

KENMORE CONNECT TM SYSTEM ...................................... 27

TROUBLESHOOTING GUIDE

Normal Sounds You May Hear ......................................... 28

Before Calling for Service .......................................... 28-30

WARRANTY ............................................................................ 31

in the space below, record the date of purchase, model, and serial number of your product. You will find the model and seriat number printed on an identification plate located inside the washer lid. Have these items of information available whenever you contact Sears concerning your product.

Model No. Date of Purchase

Serial No. Save these instructions and your sales receipt for future

reference.

Master Protection Agreements

Congratulations on making a smart purchase. Your new Kenmore ®product is designed and manufactured for

years of dependable operation. But like all products, it

may require preventive maintenance or repair from time to time. That's when having a Master Protection Agreement can save you money and aggravation.

The Master Protection Agreement atso helps extend the

life of your new product. Here's what the Agreement s includes:

* Parts and labor needed to help keep products operating

properly under normal use, not just defects. Our coverage goes well beyond the product warranty. No deductible, no functional failure excluded from coverage - real protection.

* Expert service by a force of more than 10,000 authorized

Sears service technicians, which means someone you can

trust will be working on your product.

* Unlimited service calls and nationwide service, as often as

you want us, whenever you want us.

* "No=lemon" guarantee - replacement of your covered

product if four or more product failures occur within twelve months.

* Product replacement if your covered product can not

be fixed.

* Annual Preventive Maintenance Check at your request - no

extra charge.

* Fast help by phone - we call it Rapid Resolution. Phone

support from a Sears representative on all products. Think of us as a "talking owner's manual."

* Power surge protection against electric damage due to

power fluctuations.

* $250 food loss protection annuaffy for any food spoilage

that is the result of mechanical failure of any covered

refrigerator or freezer.

* Rental reimbursement if repair of your covered product

takes longer than promised.

* 10% discount off the regular price of any non-covered repair

service and related instafled parts.

Once you purchase the Agreement, a simple phone

call is all that it takes for you to schedule service. You

can call at any time day or night or schedule a service

appointment online.

The Master Protection Agreement is a risk-free purchase.

If you cancel for any reason during the product warranty period, we will provide a full refund, or a

prorated refund any time after the product warranty

period expires. Purchase your Master Protection Agreement today!

Some limitations and exclusions apply.

For prices and addltlonal information in the U.S.A.

call 1=800=827=6655.

_Coverage in Canada varies on some items.

For full detalls call Sears Canada at 1=800=361=6665.

Sears Installaflon Service

For Sears professional installation of home appliances,

garage door openers, water heaters, and other major

home items, in the U.S.A. or Canada call:

1-800-4-MY-HOME ®.

Therearemanyimportantsafety messages in this manual and on your appliance. Always read and obey

all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can result in property damage and/or serious bodily harm or death.

Aii safety messages wiii follow the safety alert symbol and either the word DANGER or WARNING.

These words mean:

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

To reduce the risk of fire, electric shock, or injury to

persons when using this appliance, fallow basic precautions, including the following.

° Before use, the washer must be properly installed as

described in this manual.

° Do not wash articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry cleaning

solvents, or other flammable or explosive substances, as

they give off vapors that could ignite or explode.

° Do not add gasoline, dry cleaning solvents, or other

flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

° Under certain conditions, hydrogen gas may be produced

in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

system has not been used for such a period, before using

the washer, turn ON aii hot water faucets and let the water

flow from each for several minutes. This wiii release any accumulated hydrogen gas. As the gas is flammable, do not

smoke or use an open flame during this time.

° Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used near children.

° Before the washer is removed from service or discarded,

remove the door to prevent children from climbing inside.

° Do not install or store the washer where it will be exposed

to the weather or freezing temperatures.

° Do not tamper with controls.

° Do not repair or replace any part of the washer or attempt

any servicing other than as described in this manual. We

strongly recommend that any service be performed by a qualified technician.

* See Installation Instructions for grounding requirements.

° ALWAYS follow the fabric care instructions supplied by the

garment manufacturer.

* Do not place items exposed to cooking oil in your washer.

Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

° Use fabric softeners or products to eliminate static only as

recommended by the manufacturen

° This washer is not designed for maritime use or for mobile

installations such as in RVs, aircraft, etc.

° Turn OFF the water faucets and unplug the washer if the

machine is to be left for an extended period of time, such as during vacations.

° Packaging material can be dangerous for children. ° There is a risk of suffocation. Keep aii packaging from

children.

" Always check the inside of the washer for foreign objects

before loading laundry. Keep the door closed when not in

use.

*WARNING: This product contains chemicals known

to the State of California to cause cancer and birth

defects or other reproductive harm. Wash hands after

handling.

To reduce the risk of fire, electric shock, or injury to

persons when using this appllance, follow basic precautions, includlng the followlng.

° Unplug the washer before cleaning to avoid the risk of

electric shock.

• Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will damage the finish.

° Do not put oily or greasy rags or clothing on tap of the

washer. These substances give off vapors that could ignite the materials.

• Do nat wash items that are sailed with vegetable or cooking oil. These items may contain some oil after laundering and may catch fire.

• Disconnect this appliance from the power supply before attempting any user maintenance. Turning the controls to

the OFF position does not disconnect this appliance from

the power supply. Failure to follow this warning can cause serious iniury, fire, electric shock, or death.

° Do not combine detergents, fabric softeners, and/or other

laundry products from different manufacturers for use in a load, unless specified on the fabric label

° Do not mix chlorlne bleach with ammonia or acids such

as vinegar. Faffaw package directions when using laundry

products. Incorrect usage can produce poisonous gas, resulting

in serious injury or death.

* Do not reach into the washer while parts are moving.

Before Ioadlng, unloadlng, or adding items, push in the

cycle selector knob and affow the drum to coast to a complete stop before reaching inside. Failure to follow this

warning can cause serious injury, fire, electric shock or death.

° Refer to INSTALLATION iNSTRUCTiONS far detailed

grounding procedures. Installation instructionsare packed in the washer for the installer_s reference. If the washer is

moved to a new location, have it checked and reinstalled by a qualified service technician. Failure to fallow this warning can

cause serious iniury, fire, electric shock, or death.

° Do not, under any circumstances, cut or remove the third

(ground) prong from the power cord. Failure to follow this

warning can cause serious injury, fire, electric shock, or death.

° For personal safety, this appfiance must be properly

grounded. Failure ta fallow this warning can cause serious injury, fire, electric shock, or death.

* The power cord of this appfiance is equipped with a

3-prong (grounding) plug which mates with a standard 3-prong (grounding) waft autJet to minimize the possibility of

electric shock hazard from this appliance.

° This washer must be plugged into a 120VAC, 60Nz

grounded outJet. Failure to fallow this warning can cause serious iniury, fire, electric shock, or death.

* Nave the waft ouffet and circuit checked by a quafffied

eJectrlclan to make sure the ouffet is properly grounded.

Failure to fallow this warning can cause serious injury, fire,

electric shock, or death.

* Where a standard 2-prong waft ouffet is encountered, it

is your personal responsibility and abffgatlon to have it

replaced with a properly grounded 3-prong waft outlet. Failure ta fallow this warning can cause serious injury, fire,

electric shock, ar death.

* Do nat instaff an carpet. Instaff the washer on a soffd floor.

Failure to fallow this warning can cause serious leak damage.

° Do nat remove grounding prong. Do nat use an adapter or

extension cord. Plug into a grounded 3-prong auffet. Failure to fallow these warnings can cause serious injury, fire, electric shock, or death.

° The washer should always be plugged into its own

indivldual electrlcal outlet which has a voffage rating that matches the rating plate. This provides the best

performance and also prevents overloading house wiring

circuits which could cause a fire hazard from overheated wires.

° Never unplug your washer by pulling on the power

cord. Always grip plug firmly and pull straight out from the outlet. Failure to fallow this warning can cause serious iniury, fire, electric shock, or death.

° Immediately repair or replace all power cords that have

become frayed or otherwise damaged. Do nat use a cord that shows cracks or abrasion damage along its length or at either end. Consult with a qualified service technician.

Failure to fallow this warning can cause serious iniury, fire, electric shock, or death.

° When installing or moving the washer, be careful not to

pinch, crush, or damage the power cord. Failure to follow this warning can cause serious injury, fire, electric shack, or

death.

° The washer must be installed and electrlcaffy grounded

by a quafffied service technician in accordance with local codes to prevent shock hazard and assure stability during

operation.

° The washer is heavy. Two or more people may be

needed to instaff and move the appffance. Failure to do so can result in damage to property or serious bodily injury.

° Store and install the washer where it will nat be exposed

to temperatures below freezing or exposed to outdoor weather conditions. Failure to follow this warning can cause serious leak damage.

° To reduce the risk of electric shock, do nat install the

washer in humid spaces. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

*Donotallowchildrento playonor inthewasher.

Closesupervision of children is necessary when the

washer is used near children. As children grow, teach them the proper, safe use of all appliances. Failure to comply with these warnings could result in serious

personal injury.

* Destroy the carton, plastic bag, and other packing

materials after the washer is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers. Failure to comply with these warnings could result in serious personal injury.

* Keep laundry products out of children's reach. To

prevent personal injury, observe all warnings on product labels. Failure to comply with these warnings could result in serious personal injury.

• Before your washer is removed from service or discarded, remove the lid to the washing compartment to avoid the danger of children or small animals getting

trapped inside. Failure to do so can result in serious

personal injury or death.

IMPORTANT: Please read carefully. TO CONNECT ELECTRICITY

Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check

with a qualified electrician or service technician

if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance. If it does not fit the outlet, have a proper outlet installed by a qualified electrician. Failure to follow these warnings can cause serious injury, fire, electric shock, or death.

3-prong

grounding type

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least

resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes

and ordinances.

3-prong grounding plug

"Ensure proper

ground exists before use.

KEY PARTS AND COMPONENTS

DETERGENT DISPENSER

There are four comparfements. One each for prewash, main wash, liquid bleach, and liquid fabric

softener.

CONTROL PANEL

The easy-to-read LED display shows cycle options, settings, cycle status, and estimated time remaining during operation. NOTE: Sensors in the washer automatically detect the size of the wash toad to optimize washing time, based on the selected cycle and options.

DIRECT-DRIVE MOTOR

The direct-drive motor provides improved performance and reliability while increasing energy emciency.(Motor is not visible.)

LARGE-CAPACITY STAINLESS STEEL DRUM

The ultra-large stainless steel drum offers extreme durability and is tilted to improve ef_ciency and allow easier access for large items.

O ASY-ACCESS LOCKING DOOR

The extra-large door locks during operation. The door will not open until it is safe to do so.

FILTER ACCESS PANEL

Provides easy access to the drain pump filter, which allows you to clean the filter or retrieve lost items

without a service call.

Cold and Hot Water Inlets

Power,

Cord

LEVELING FEET

Four leveling feet (two in the front and two in the back adjust to improve washer stability on uneven floors. Feet are adjusted and locked in place using the adjusting wrench included with the washer.

Non-skid pads

Wrench (for removing

shipping bolts and

locking leveling feet)

included Accessories

(for covering shipping bolt

Tie Strap

(for securing

drain hose)

Caps(4)

holes)

Elbow Bracket

(for securing drain

hose)

Wrench appearance may vary.

Rear of Washer

Shipping Botts/Retainers (4)

NOTE: Bolts/Retainers MUST be removed prior

be operation. Keep for future use.

f Optional Accessories _-"

Drain Hose Extension Pedestal

51022(Whlte) D26 17008 (Ginger) 51028(Patlna Beige) D26 17009 (Chili pepper)

51025(Blue Silver) 51029(Sears Red)

Hot and Cold 51027(Titanlum)

Water Hoses

51026(STS)

Stacking kit(For dryer)

D26 17002 (White)

KEY DiMENSiONS AND SPECiFiCATiONS

Description Front-Loading Washer Rated Voltage/Frequency 120VAC, 60Hz

Dimensions 27 in.(W)×293/4 in.(D)×3811/16 in.(H), 51 in.(D, door open)

68.6 cm (W) X 75.6 cm (D) X 98.3 cm (H), 129.5 cm (D, door open)

Net Weight 84.90kg(187.171b)

CHOOSE THE PROPER LOCATION CLEARANCES

WARNING

* This washer is heavy. Two or more people are required

when moving and unpacking the washer. Failure to do so

may result in damage to property or serious bodily harm.

* Store and install the washer where it will not be exposed

to temperatures below freezing or exposed to outdoor

weather conditions. Failure to follow this warning can cause

serious injury, fire, electric shock, or death. Properly ground washer to conform with all electric governing codes and ordinances. Failure to follow this warning can cause serious iniury, fire, electric shock, or

death.

* To reduce the risk of electric shock, do not install the

washer in humid spaces. Failure to follow this warning can

cause serious injury, fire, electric shock, or death.

* To ensure proper air flow, do not block the large opening

on the bottom of the washer with carpeting or other materials.

* Do not remove ground prong. Do not use an adapter

or extension cord. Plug into a grounded 3=prong outlet. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

Power Outlet

° The power outlet must be within 60 in. (1.5 m) of either side

of the washer.

° The appliance and outlet must be positioned so that the

plug is easily accessible.

° Do not overload the outlet with more than

one appliance.

° The outlet must be grounded in accordance with current

wiring electric codes and regulations.

* Time-delay fuse or circuit breaker is recommended. NOTE: It is the personal responsibility and obligation of

the product owner to have a proper outlet installed by a qualified service technician.

22 1/4"_

(57 cm)

(75.6 cm) (10 cm)

14 293/4" 4"

To ensure sufficient clearance for water lines and airflow, allow minimum clearances of at least 1in. (2.5 cm) at the sides and 4 in. (10 cm) behind the unit. Be sure to allow for wall, door, or floor moldings that may increase the required clearances.

1' 27" 1'

(2.5 cm) (68.6 cm) (2.5 cm)

51"

(129.5cm)

FLOORING

° To minimize noise and vibration, the washer MUST be

installed on a solidly constructed floor. See the NOTE to

your right.

° Allowable slope under the entire washer is a maximum 1 in.

difference from side to side or from front to back.

° Installing on carpeting and soft tile surfaces is not

recommended.

° Never install the washer on a platform or weakly supported

structure.

Allow at least 21 1/4in. (54 cm) in front of

the washer to open the door.

NOTE: The floor must be strong and rigid enough to support the weight of the washer, when fully loaded,

without flexing or bouncing, if your floor has too much

flex, you may need to reinforce it to make it more rigid.

A floor that is adequate for a top-loading washer may

not be rigid enough for a front loading washer, due to

the difference in the spin speed and direction, if the

floor is not solid, your washer may vibrate and you may hear and feel the vibration throughout your house.

UNPACKING AND REMOVING SHiPPiNG BOLTS

When removing the washer from the carton base, be sure

to remove the foam drum support in the middle of the

carton base. See drawing below. if you must lay the washer down to remove the base

packaging materials, always protect the side of the washer and lay it carefully on its side. DO NOT lay the washer on its front or back.

To prevent internat damage during transport, the washer

is equipped with four shipping bolts and plastic retainers.

iMPORTANT:

* These shipping bolts and retainers MUST NOT be re-

moved until just before moving the washer into its final position.

* These bolts and retainers MUST be removed before

operating the washer. Failure to remove shipping bolts and retainers may

cause severe vibration and noise, which can lead to permanent damage to the washer.

NOTE: The power cord is secured to the back of the washer with a shipping bolt to help prevent operation with shipping bolts in place.

Shipping Bolts

" Power

Cord

1. Save the foam block for future use. If the washer must be moved in the future, this will help prevent

damage to the washer during transportation.

Shipping

Bolts

2. Remove the bolt assemblies by wiggling them slightly while pulling.

3. Locate the four hote caps included in the accessory

pack and install them in the shipping bolt holes. NOTE: Save the bolt assemblies for future use. To prevent damage to internal components, DO NOT

transport the washer without reinstalling the shipping

bolts.

CONNECTING THE WATER LINES

* IMPORTANT: Use new hoses when installing the washer. Do

NOT reuse old hoses.

* Water supply pressure must be between 14.5 psi and 116 psi

(100-800 kPa). If the water supply pressure ismore than 116 psi, a

pressure reducing valve must be installed.

* Periodically check the hose for cracks, leaks, and wear, and

replace the hose if necessary.

* Make sure that the water lines are not stretched, pinched,

crushed, or kinked.

* The washer should never be installed or stored in a location

subject to freezing temperatures. Damage to the water lines and internal mechanisms of the washer can result. If the washer was

exposed to freezing temperatures prior to installation, allow it to stand at room temperature for several hours before use and check

for leaks prior to operation.

Rubber Seal

3.Always run a gallon or two of water through each inlet hose to flush dirt, scale and other debris out of the water lines. Doing so will help prevent future problems with clogged filter screens, and will also

allow you to verify which hose is hot and which is cold.

Water Hose (to water inlet

Water Hose

1. Inspect the threaded fitting on each hose and make sure there is a rubber seal in place in both ends.

Water Fa_

2. Connect the water supply hoses to the HOT and COLD water faucets tightly by hand and then tighten another 2/3turn with pliers.

Hot Cold Water Water Inlet

Inlet

4. Attach the (red) hot water line to the hot water inlet on the back of the washer. Attach the (btue) cotd water line

to the cold water inlet on the back of the washer.

NOTE: When installing the hoses onto the water inlet

valves, be careful not to cross-thread the hose fittings. DO

NOT overtighten the hoses; this could cause damage to internal components, the valve or the hose gasket. Over- tightening could result in property damage from leaks.

CONNECTING THE DRAIN HOSE

° The drain hose should always be properly secured. Failure to

properly secure the drain hose can result in flooding and property damage.

° Do not install the end of the drain hose higher than 96 in. (243.8

cm) above the bottom of the washer.

° The drain must be installed in accordance with any applicable

local codes and regulations.

° Make sure that the drain hose is not stretched, pinched, crushed,

or kinked.

NOTE:

A drain hose extension kit is

available if the drain hose is not ioncj enough. Do not extend the

drain hose more than 6 feeh as this wiii cause poor draining, which wiii result in poor wash

and spin performance.

Option 1: Standpipe

Option 2: Laundry Drum

_ ,e_t_ S'n k

_e_Strapl -_

Drain Hose

The elbow bracket should be installed near the end of

the drain hose° Hang the end of the drain hose over the

side of the utility sink. Use a tie strap to secure the drain hose in place°

Option 3: Floor Drain

Elbow Bracket

Stra

\ J

Install the end of the drain hose into the elbow bracket.

Do not extend the drain hose more than 4 inches past the end of the elbow bracket. Use a tie strap to secure the drain hose in place.

NOTE:

* Total height of the hose end should not exceed 96 in.

(243.8 cm) from the bottom of the washer.

* The drain hose should be inserted no more than 8-12

inches into the standpipe. Inserting more than 8-12 inches can cause mold or microorganisms to spread to

the inside of the washer.

Drain Hose

Floor Drain

Insert the end of the drain hose into the floor drain° If possible, secure the hose to prevent it from moving or

coming out of the drain.

CONNECT TO THE POWER SUPPLY

Washer should be plugged into a 120-VAC, 60-Hz grounded 3-prong outlet.

Plug in the washer.

LEVELING THE WASHER

The drum of your new washer spins at very high speeds. To minimize vibration, noise, and unwanted movemenh the floor must be a level, solid surface. NOTE: Adjust the ieveiincj feet only as far as necessary to level the washer. Extendincj the ieveiincj feet more than necessary can cause the washer to

vibrate.

NOTE: Before instaiiincj the washer, make sure that the floor is clean, dry and free of dush dirt_ water and oils so the washer feet cannot slide easily. Leveiincj feet that

move or slide on the floor can contribute to excess vibration and noise due to

poor contact with the floor. See

INSTALLATION OF NON-SKID PADS for more information.

NOTE: If a drip pan must be used, make sure to follow the instructions provided with the drip pan and make sure the

levelincj feet are adjusted for firm and even contact with the pan. Use of drip pans and failure to properly level the

machine may result in increased vibration and noise durincj operation. All four levelincj feet must rest solidly on the floor. Rock

the washer from corner to corner to make sure that all four levelincj feet are in firm and even contact with the floor.

Tighten all 4 lock nuts

securely using the

wrench.

3. Once the washer is level from side to side and front to back, use the adjusting wrench to tighten all four lock

nuts securely to prevent the legs from getting out of adjustment during operation. Make sure that all four leveling feet are in flrm contact with the floor.

NOTE: To make sure that the washer is properly level, run the washer with a test load: place a medium-sized load of laundry in the machine. Then, press POWER, select RINSE & SPIN, and

press the START/PAUSE button. See the followincj sections for additional information on cycle

selection and operation. Verify that the washer does not rock or vibrate excessively during the spin cycle. If the washer vibrates or shakes, adjust the ieveiincj feet_ while the washer is spinnincj,

until the vibrations are reduced.

\ Leveling Feet

1. Position the washer in its final location, taking special care not to pinch, strain, or crush the water and drain lines° Place a level across the top of the washer

2. Loosen the locknuts on all four leveling feet with the

wrench until you can adjust the feet (wrench appearance

may vary). Use the wrench to turn the feet clockwise

to raise the washer, and counterclockwise to lower the washer. Using a level, adjust the feet until the washer is

level from side to side and front to back. Make sure that

all four feet are in firm contact with the floor.

NOTE: If you are installing the washer on the optional pedestal, the washer leveling feet should be fully retracted. Use the leveling feet on the pedestal to level the washer.

INSTALLATION OF NON-SKID PADS (optional)

Some floor surfaces are too slippery to prevent the washer from moving on the floor during heavily unbalanced

loads. While it is normal for an occasional toad to be out of balance, excess noise and vibration can result from the

washer moving out of position° If these conditions are en- countered, follow the instructions below for installation of the non-skid pads° These pads will help prevent the washer from moving during heavy, out of balance conditions, thereby reducing noise and vibration.

NOTE: The non-skid pads are included in the installation

packet

Non-skid pads

his side up

Stick adhesive side to floor move backing

*Place the pads under bothfront feet.

_e WARNING: To reduce the risk of electrlc shock, or injury to persons, read and follow this

ntire Use & Care Guide, including the important Safety instructions, before operating this washer.

CONTROL PANEL FEATURES

Normal

Bulky

Heavy Duty

Whites

POWER

O POWER (ON/OFF) BUTTON

Press to turn the washer ON or OFF. NOTE: Pressing the POWER button during a

cycle will cancel that cycie and any toad settings will be lost. The door will unlock after a brief

pause, unless the water level or temperature is too high.

CYCLE SELECTOR KNOB

Turnthis knob to select the desired cycie. Once the desired cycte has been selected, the standard presets

witI appear in the display. These seffings can be adjusted using the cycle seffing buttons anytime

before starting the cycle.

Express Wash

CoredCmean

Delicates

Rinse & Spin

O YCLE MODIFIER BUTTONS

Use these buttons to adjust the settings for the selected cycle. The settings light up above the

buttons to show the current selection.

O PECIAL CYCLE AND OPTION BUTTONS

These buttons allow your to select special cycles or options.

O IME AND STATUS DISPLAY

The display shows the cycle status and estimated

time remaining°

START/PAUSE BUTTON

Pressthisbutton to start the selected cycle. If the washer is running, use this button to pause the cycte without losing the current settings.

NOTE: If you do not pressthe START/PAUSEbutton within four minutes of selecting a cycle, the washer auto- maficaliy turns OFF.

NOTE: To protect your clothing, not all settings are available on all cycle selections.

OPERATING THE WASHER

POWER

Normal

Bulky

Heavy Duty

Whites

R_nse& Spin

SORT LAUNDRY AND LOAD WASHER Sort laundry by fabric type, soil level, color and load size, as

needed. Open the door and load the items into the washer.

TURN ON THE WASHER

Press the POWER button to turn ON the washer. The lights around the cycle selector knob will illuminate and a chime will

sound.

SELECT A CYCLE

Turn the cycle selector knob in either direction to select the desired cycle. The preset Wash Temperature, Spin Speed, Soil Level, and Option settings for that cycle will be shown.

SELECT CYCLE MODIFIERS & OPTIONS

Default settings for the selected cycle can now be changed if desired. Use the cycle modifier buttons.

NOTE: To protect your fabrics, not all modifiers are available on all cycles. Cycle options can also be added by using the option buttons. NOTE: Not all options are available on all cycles. A different

chime will sound and the LED will not come on if the selection is not allowed.

ADD DETERGENT

Add High=Efficiency (HE) detergent to the detergent dispenser drawer. For proper wash performance, always measure the detergent using the measurements provided by the detergent

manufacturer.

STARTIPAUSE

O EGIN CYCLE

Press the START/PAUSE button to begin the cycle. The door will lock, and the washer will briefly tumble the toad without water

to measure its weight. Once the weight of the load is measure, the washer will begin the selected wash cycle.

TO PAUSE THE CYCLE

To pause the washer during a cycle, press the START/PAUSE button. To resume the cycle, press the START/PAUSE button again.

O RESUME CYCLE

Press the START/PAUSE button to resume the wash cycle.

CYCLE GUIDE

The cycle guide below shows the default settings, available options and recommended fabric types for each cycle. Allowable modifier adjustments are shown below the default setting for each cycle. : Default Setting

@ = Available Option

Normal

Bulky

Heavy

Duty

Whites

Cotton, linen, towels, shirts, sheets, jeans,

mixed loads

Large items

such as

blankets and

comforters

Heavy soiled

cotton fabrics

Heavily to normally

soiled white cottons

Hot

Tap Cold

Cold

Eco Warm

Hot

Tap Cold

Cold

Eco Warm

Hot

Tap Cold

Cold

Eco Warm

Tap Cold

Cold

Eco Warm

Wa r m

Extra

High

No Spin

Low

Medium

No Spin

Low

No Spin

Low

Medium

High

Extra

High

No Spin

Low

Medium

Heavy

Light

Heavy

Light

Normal

Heavy

Light

NOTE: * To protect your garments, not every wash temperature, spin speed, soil level, or option is available with every cycle.

A chime will sound and the LED will not light if the selection is not allowed.

" The washer automatically adjusts the wash time for the amount of laundry, water pressure, water heating time and

other operating conditions.

" These cycles use various wash motions to enhance cleaning and/or fabric care performance. The wash motions

may sound different at different stages of the wash cycle. This is normal.

CYCLE GUIDE

The cycle guide below shows the default settings, available options and recommended fabric types for each cycle. Allowable modifler adjustments are shown below the default setting for each cycle.

= Available Option

: Default Setting

Express

Wash

Cold

Clean

Deiicates

Rinse and

Spin

Lightly soiled clothing and small loads

Small loads of cotton,

linen, towels, shirts, sheets, jeans, mixed

load

Dress shirts/

blouses,

nylons, sheer or lacy garments

Loads that

only need to

be rinsed

TapCold

Cold

EcoWarm

Warm

Tap Cold

Eco Warm

Warm

Tap Cold

No Spin

Low

Medium

High

Extra

High

No Spin

Low

Medium

No Spin

Low

Extra

High

No Spln

Low

Medium

Normal

Heavy

Light

Heavy

Light

NOTE: * To protect your garments, not every wash temperature, spin speed, soil level, or option is available with every cycle.

A chime will sound and the LED will not light if the selection is not allowed.

* The washer automatically adjusts the wash time for the amount of laundry, water pressure, water heating time and

other operating conditions.

* These cycles use various wash motions to enhance cleaning and/or fabric care performance. The wash motions

may sound different at different stages of the wash cycle. This is normal.

SORTING WASH LOADS

Fabric Care Labels

Many articles of ctothing include a fabric care label. Using the chart below, adjust the cycle and option selections to care for your clothing according to the

manufacturer's recommendations.

Fabric Care Labels

Machine

wash,.. _1 _ _

CyCle Normal Permanent press/ Gentle/

Water • Q • • • • temperature ,or Warm Cold/c001

Bleach symbols A Z_ ._

wrinkle resistant delicate

H h Do net wash Do not wring

Any bleach 0nly n0n-chl0rine bleach Do not bleach

(when needed) (when needed)

Grouping Similar Items

For the best washing results_ and to reduce the possibility of damage to clothing, care should be taken to sort the clothing into loads that are made up of similar items.

Mixing different fabric types and/or sail levels can result in poor wash performance° color transfer or discoloration° fabric damage or linting. Fabrics should be sorted into groups as described below.

Carats

Sort articles by color. Wash dark clothes together in a separate load from light colors or whites. Mixing dark

clothes with light clothes can result in dye transfer or discoloration of the lighter clothes.

Sall Level Wash heavily soiled clothing together. Washing lightly

soiled clothing in the same load with heavily soiled clothing could result in poor wash performance for the lightly soiled clothing.

Fabric Type Delicate articles should not be mixed with heavier or

sturdier fabric types. Washing delicates in a load with heavy fabrics can result in damage to the more delicate fabrics. Washing heavier fabrics in a delicate load can result in poor wash performance for the heavier fabrics and possible damage to the delicates.

Lint Type Some fabrics attract and bind lint to them while others

give off lint in the laundry process. Avoid mixing these lint collectors and lint producers in the same load. Mixing

these fabrics will resuff in pilling and linting on the lint

collectors. (For example r lint collector - knit sweater; lint producer - terrycloth towels.)

Loading the Washer

* Check all pockets to make sure that they are empty.

Items such as clips, matches, pens, coins, and keys can

damage both your washer and your clothes.

* Close zippers, hooks, and drawstrings to prevent these

items from snagging or tangling on other clothes.

* Pretreat heavily stained areas for best results.

* Combine large and small items in a load. Load large

items first.

* Large items should not be more than half of the total

wash load. The drum should not be tightly packed with items. The

door of the washer should close easily. To prevent an out-of-balance load, do not wash single

items. Add one or two similar items to the load.

* Large, bulky items, such as a blanket, comforter, or

bedspread, should be washed individually.

* Do not wash or spin waterproof items, such as rain coats,

sleeping bags, etc.

* When unloading the washer, check under the door seal

for small items.

NOTE: Make sure that the door seal area is clear when

closing the door. Overloading the washer can cause items to get caught between the door and the seal. This can damage both the items and the seal.

* DO NOT OVERLOAD THE DRUM * MAKE SURE CLOTHING IS NOT

CAUGHT IN THE DOOR GASKET

f Sort Laundry..,

Whites by Colors

Lights

X,_ barks

by Soil Heavy

Normal Light

by Fabric Delicates

Easy Care Sturdy

by Lint Lint Producer

Lint Collector

ABOUT THE DISPENSER DRAWER

*The automatic dispenser consists of four compartments

which hold.

* Liquid chlorine bleach. * Liquid fabric softener.

* Liquid or powdered detergent for prewash. * Liquid or powdered detergent and color-safe bleach

for main wash.

Pre-Wash Detergent Compartment

Add liquid or powdered detergent to this compartment when using the Pre-Wash option. Always use High-

Efficiency (HE) detergent with your washing machine.

The amount of detergent added for the Pre-Wash option should be 1/2the amount recommended for the

main wash cycle. For example, if the main wash cycle requires 1/2measure of detergent, add 1/4measure to the Pre-Wash compartment.

NOTE: If using liquid detergent for the main wash when

using the Pre-Wash option, the liquid detergent cup accessory must be used in the main wash dispenser. This will prevent the main wash liquid detergent from being dispensed immediately.

Main Wash Detergent Compartment

This compartment holds laundry detergent for the main wash cycle. The detergent is added to the load at the beginning of

the cycle. Always use High-Efficiency (HE)detergent with your washing machine. Either powdered or liquid detergent may be

used.

Never exceed the manufacturer's recommendations when adding detergent. Using too much detergent can result in

detergent buildup in clothing and the washen

NOTE: Liquid or powdered color-safe bleach may be added to the main wash compartment with detergent of the same

type. DO NOT add liquid or powdered color-safe bleach to the

bleach dispenser.DO NOT mix liquid and powdered cleaning agents within the same compartment.

Liquid Chlorine Bleach

Compartment

Liquid Fabric

Softener Compartment

Liquid Detergent Cup

Prewash Detergent

Compartment

Main Wash Detergent Compartment

Liquid Bleach Compartment

This compartment holds liquid chlorine bleach, which is dispensed automatically at the proper time during the

wash cycle.

* Do not add powdered or liquid color-safe bleach to this

compartment. The bleach compartment is designed to dispense liquid chlorine bleach only. Powdered or liquid color-safe bleach will not dispense properly.

* Always follow the manufacturer's recommendations when

adding bleach. Do not exceed the maximum fill line since this can cause the bleach to be dispensed immedi-

ately, causing damage to fabrics. Using too much bleach can damage fabrics.

Never pour undiluted liquid chlorine bleach directly onto

the load or into the drum. Fabric damage can occur.

Fabric Softener Compartment

This compartment holds liquid fabric softener, which is automatically dispensed during the final rinse cycle.

Never exceed the manufacturer's recommendations

when adding softener. Using too much fabric softener can result in buildup in clothing and the washer. Either

powdered or liquid fabric softener may be used.

Always follow the manufacturer's recommendations when adding fabric softener. Do not exceed the maximum fill line. Using too much fabric softener may stain clothes.

Dilute concentrated fabric softeners with warm water. Do

not exceed the maximum fill line.

* Never pour fabric softener directly onto the load or into

the drum.

DETERGENT AND DISPENSER USE

A Word About Detergents

High-Efficiency (HE) detergents produce fewer suds, dissolve more efficiently to improve washing and rinsing performance, and help to keep the interior of your

washer clean. Using detergent that is not HE may cause

oversudsing and unsatisfactory performance which could result in error codes, cycle failure, and machine damage.

-- Maximum ______--:1

_--Normal Load Amount_

Liquid Powdered

Detergent Detergent

For proper wash performance, always measure the detergent using the measurements provided by the detergent manufacturer.

The normal amount of HE detergent needed, for average loads, is tess than 1/2of the recommended maximum. Use less detergent for soft water, light soil or smaller

loads. Never use more than the maximum amount recommended by the detergent manufacturer.

Detergent Amount

For proper wash performance, always measure the de- tergent using the measurements provided by the deter- gent manufacturer.

Filling the Dispenser

To add detergent, bleach, and fabric softener to the automatic dispenser:

Open the drawer.

O oad the laundry products into the

appropriate compartments.

O Close the drawer before the cycle.

NOTE: It is normat for a small amount of water to

remain in the bleach and softener compartments at the end of the cycle.

IMPORTANT: Do not place or store laundry products, such as detergent, bleach, or liquid fabric softener, on top of your washer or dryer. Wipe up any spills immediately. These products can damage the finish and controls.

dispenser

starting

Designed to use only High-Efficiency (HE) detergent

IMPORTANT: Your washing machine isdesigned for use with only High-Efficiency (HE) detergents. HE detergents are formulated specifically for High-Efficiency washers and contain suds-reducing agents. Always look for the HE symbol when purchasing detergent.

IMPORTANT: Not all detergents are the same. Pay careful attention to the amount of detergent used to avoid overusing, poor rinsing and detergent buildup in clothing, and residue buildup that can contribute to odors in the machine. NEVER use a cup or scoop other than the one supplied by the manufacturer of the detergent you are using. Never use more than the maximum amount of detergent recommended by the manufacturer.

Always measure the detergent amount. While HE

detergents are designed for this type of washing machine, be careful when measuring the detergent. For most normal loads, no more than 1/4to 1/2 of cap or scoop of HE detergent should be used.

NOTE: Extra care must be exercised when using 2X and 3X concentrated detergents because even a little bit extra can contribute to the problems mentioned above.

NOTE: Detergents designated as HE compatible may not provide optimal results.

MAGNETIC DOOR PLUNGER

Safely and conveniently secure the door slightly ajar with the magnetic door plunger. This will promote air circula-

tion and allow the interior of the machine to dry. To use this feature, after the load has been removed, do not

close the door completely. When the magnetic door plunger comes into contact

with the metal washer cabinet, it will secure the door slightly open allowing the interior of the washer to dry.

TIME AND STATUS DISPLAY

The time and status display shows the estimated time remaining, cycle progress, and door lock status.

IWoshTom0IS0nSpoe ]SoLevem[Chinel

A[Hcot_ RHnses

O ESTIMATED TiME REMAiNiNG

When the START/PAUSE button is pressed, the wash- er witl automatically detect the load size for cycles

that use load sensing. The control will then optimize the wash and rinse times, based on the selected

cycle, modifiers and options. When the load size has been determined, the disptay will change from dashes (- - -) to the estimated time for that cycle. For non-load sensing cycles, the estimated time witl

display when the cycle is selected. NOTE:

• The time shown is only an estimate. For example, the time displayed may pause for a period of time while the machine is heating the water or balanc-

ing the load. Under certain conditions, the machine can pause for extended periods of time.

• Estimated time is based on normal operating con- ditions. Several external factors (load size, room

temperature, incoming water temperature, etc.) also affect the length of estimated time vs. actual time.

LOAD-SENSING iNDiCATOR

At the beginning of cycles that use the load sensing

feature, the LOAD SENSING light will blink while the load size is being measured. Once the size has been determined, the control adjusts the cycle for opti- mum performance. Estimated time remaining will not display until the load size has been determined, and

may be different for each load.

CYCLE STATUS iNDiCATOR

These status LEDs illuminate to indicate which stage of the cycle is currently running. A blinking light indi- cates the active stage of the cycle. When that stage

is complete, the light witl remain steady. DOOR LOCi( iNDiCATOR

indicates that the door is locked. The washer door

will lock while the washer is operating. The door can

be unlocked by pressing START/PAUSE to pause the

washer.

NOTE: * if the temperature in the washer is too high, the

door cannot be unlocked until the washer has cooled.

" If the water level is too high, the door will not

unlock. To drain the water, press POWER, then press the SPIN SPEED button without selecting a cycle. Press START/PAUSE and the water will drain and the clothes will spin out. Do not try to force the

door open, as it will damage the door.

CYCLE MODiFiER BUTTONS

Each cycle has default settings that are selected

automatically. You may also customize these settings using the cycle modifier buttons. Press the button for the desired modifier until the indicator light for the desired

value is lit. The washer automatically adjusts the water

level for the type and size of wash toad for best results and maximum emciency. Due to the high-efficiency nature of this product, water levels may be much lower

than expected. This is normal operation and cleaning/

rinsing performance will not be compromised.

NOTE: To protect your garments, not every wash tem- perature, spin speed, soil level, or option is available

with every cycle. A chime will sound and the LED will

not light if a selection is not allowed.

O WASH TEMP

Wash Temp selects the wash and rinse temperature combination for the selected cycle. Press the Wash Temp button until the indicator light for the desired setting is lit.

° Your washer features a heating element to boost the hot

water temperature for Extra Hot settings. This provides

improved wash performance at normal water heater settings.

° Select the water temperature suitable for the type of

load you are washing. Follow the garment fabric care labels for best results.

° Warm rinses are regulated at approximately 86°F

(30°C).

° Warm rinses leave the clothes dryer than cold rinses_ but

will result in increased energy consumption and greater

wrinkling of clothes.

° Cold rinses use Jessenergy. The actual rinse temperature

depends on the temperature of the cold water at the faucet.

O SPIN SPEED

Higher spin speeds extract more water from clothes, reducing drying time and saving energy.

Press the SPIN SPEED button until the desired speed is selected. Some fabrics, such as delicates, require a slower spin speed. To protect your clothing, not all spin speeds are available for all cycles.

The Drain & Spln cycle:

1. Press the POWER button to turn ON the washer.

2. Pressthe SPIN SPEED button to select the desired spin speed. For drain only, select the NO SPIN option.

3. Press the START/PAUSE button. The water will drain and the clothes will tumble before the spin

routine begins.

SOIL LEVEL

Adjusting the soil level setting will modify the cycle to allow more time for heavily soiled clothes or less time for lightly soiled clothes. Press the SOIL LEVEL

button until the desired soil level is selected.

CHIME

Press repeatedly to adjust the votume of the chime and keypad tones. You may turn the end-of-cycle chime and keypad tones ON or OFF with the CHIME

button.

+ 46 hidden pages