Kenmore 79641162410, 79641162411 Owner’s Manual

Use & Care Guide

Manual de Uso y Cuidado

English / Espafiol

Model/Modelo: 796.4116"

I<enmore

IiX::o__best _esuks a IOWoS_dsing, HEkgh EF)c ency Ii}_:,e_gen_ nade tot hg e_fic_':n(y waslq_ s must

be used,, Para>bten_':r I>s mejo es es _ltados, d_:x:r,'_

ut zarse un @':tetg_':nte HE paa avadc as @': ata eficacia y has espun_a

®uto®6tic® de c® ®

s ..............co/or numb÷(, nOmero de co/or

IIIIIIIIIIIIIIIIIIIIII

MFL68639704

Sears Brands Management Corporation HofFman Estates, IL 60179 U.S.A.

www.kenmore.com www.sears.com

IMPORTANT SAFETY INSTRUCTIONS ......................... 3-5

GROUNDING REQUIREMENTS ...................................... 5

FEATURES AND BENEFITS

Key Parts and Components ................................................. 6

included Accessories ........................................................... 6

Optional Accessories ........................................................... 6

INSTALLATION REQUIREMENTS

Key Dimensions and Specifications ................................... 7

Choose the Proper Location ............................................... 7

Flooring .................................................................................. 7

Clearances ............................................................................ 7

INSTALLATION INSTRUCTIONS

Unpacking and Removing Shipping Bolts......................... 8

Connecting the Water Lines ................................................ 9

Connecting the Drain Hose ............................................... 10

Connecting to the Power Supply ....................................... 10

Leveling the Washer ........................................................... 11

installation of Non-Skid Pads (optional) ........................... 11

HOW TO USE

Control Panel Features ........................................................ 12

Operating the Washer ......................................................... 13

Cycle Guide .................................................................... 14-15

Sorting Wash Loads ............................................................ 16

About the Dispenser Drawer .............................................. 17

Detergent and Dispenser Use............................................. 18

Magnetic Door Plunger ...................................................... 18

Time and Status Display .................................................... 19

Cycle Modifier Buttons....................................................... 20

Option Buttons ..................................................................... 21

Delay Start ........................................................................ 21

Extra Rinse ........................................................................ 21

Pre Wash ........................................................................... 21

Special Functions ............................................................... 22

Control Lock..................................................................... 22

Clean Washer ................................................................. 22

Auto Soak ......................................................................... 22

CARE AND CLEANING

Regular Cleaning .......................................................... 23-24

Cleaning the Exterior ...................................................... 23

Care and Cleaning of the interior ................................ 23

Clean Washer ................................................................ 23

Door Seal and Glass Cleaning ...................................... 23

Removing Mineral Buildup .............................................. 23

Storing the Washer ........................................................ 24

Cleaning the Dispenser .................................................. 24

Maintenance .................................................................. 25-26

Cleaning the Water inlet Filters.................................... 25

Cleaning the Drain Pump Filter ..................................... 26

KENMORE CONNECT TM System ......................................... 27

TROUBLESHOOTING GUIDE

Normal Sounds You May Hear ......................................... 28

Before Calling for Service .......................................... 28-30

WARRANTY .................................................................. 31

In the space below, record the date of purchase, model,

and serial number of your product. You will find the model and serial number printed on an identification plate located inside

the washer door. Have these items of information available whenever you contact Sears concerning your

product.

Model No.

Date of Purchase

Serial No. Save these instructions and your sales receipt for future

reference.

Master Protection Agreements

Congratulations on making a smart purchase. Your new

Kenmore ® product is designed and manufactured for years of dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That's when having a Master Protection Agreement can save you money and aggravation.

The Master Protection Agreement also helps extend the life of your new product. Here's what the Agreement* includes:

oparts and labor needed to help keep products

operating properly under normal use, not just defects. Our coverage goes well beyond the product warranty.

No deductible, no functional failure excluded from

coverage - real protection.

oExpert service by a force of more than 10,000

authorized Sears service technicians, which means someone you can trust will be working on your product.

oUnlimited service calls and nationwide service, as

often as you want us, whenever you want us.

o_No-lemon" guarantee - replacement of your covered

product if four or more product failures occur within

twelve months.

oproduct replacement if your covered product can not

be fixed.

*Annual Preventive Maintenance Check at your request

- no extra charge.

*Fast help by phone - we call it Rapid Resolution.

Phone support from a Sears representative on all products. Think of us as a ""talking owner's manual."

*Power surge protection against electric damage clue to

power fluctuations.

*$250 food loss protection annually for any food

spoilage that is the result of mechanical failure of any covered refrigerator or freezer.

*Rental reimbursement if repair of your covered

product takes longer than promised.

"25°/0 discount off: the regular price of any non-covered

repair service and related installed parts.

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call at any time day or night or schedule a service appointment online.

The Master Protection Agreement is a risk-free purchase.

If you cancel for any reason during the product warranty period, we will provide a full refund, or a

prorated refund any time after the product warranty

period expires. Purchase your Master Protection Agreement today!

Some limitations and exclusions apply.

For prices and additional information in the U.S.A. call 1-800-827-6655.

*Coverage in Canada varies on some items.

For full details call Sears Canada at 1-800-361-6665. Sears Installation Service

For Sears professional installation of home appliances, garage door openers, water heaters, and other major

home items, in the U.S.A. or Canada call:

1-800-4-MY-HOME ®.

There are many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can result in property damage and/or serious bodily harm or death.

All safety messages will follow the safety alert symbol and either the word DANGER or WARNING. These words mean:

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are

not followed.

To reduce the risk of fire, electric shock, or injury to

persons when using this appliance, follow basic precautions, including the following.

•Before use, the washer must be properly installed as described in this manual.

• Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances, as they give off vapors that could

ignite or explode.

• Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash water.

These substances give off vapors that could ignite or explode.

•Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been used

for such a period, before using the washer, turn ON all hot water faucets and let the water flow from each

for several minutes. This will release any accumulated

hydrogen gas. As the gas is flammable, do not smoke

or use an open flame during this time.

•Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is

used near children.

•Before the washer is removed from service or discarded, remove the door to prevent children from

climbing inside.

•Do not install or store the washer where it will be exposed to the weather or freezing temperatures.

•Do not tamper with controls.

•Do not repair or replace any part of the washer or attempt any servicing other than as described in this

manual. We strongly recommend that any service be performed by a qualified technician.

•See Installation Instructions for grounding requirements.

•ALWAYS follow the fabric care instructions supplied by the garment manufacturer.

•Do not place items exposed to cooking oil in your washer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a

load to catch fire.

•Use fabric softeners or products to eliminate static only as recommended by the manufacturer.

•This washer is not designed for maritime use or for

mobile installations such as in RVs, aircraft, etc.

•Turn OFF the water faucets and unplug the washer if the machine is to be left for an extended period of time, such as during vacations.

•Packaging material can be dangerous for children. There is a risk of suffocation. Keep all packaging

from children.

•Always check the inside of the washer for foreign objects before loading laundry. Keep the door closed

when not in use.

•Warning: This product contains chemicals known to the State of California to cause cancer and birth defects

or other reproductive harm. Wash hands after handling.

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following.

*Unplug the washer before cleaning to avoid the risk of

electric shock.

• Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will damage

the finish.

*Do not put oily or greasy rags or clothing on top of

the washer. These substances give off vapors that could ignite the materials.

*Do not wash items that are soiled with vegetable or

cooking oil. These items may contain some oil after laundering and may catch fire.

• Disconnect this appliance from the power supply before attempting any user maintenance. Turning the controls to the OFF position does not disconnect this

appliance from the power supply. Failure to follow this

warning can cause serious injury, fire, electric shock, or death.

*Do not combine detergents, fabric softeners, and/or

other laundry products from different manufacturers for use in a load, unless specified on the fabric label.

*Do not mix chlorine bleach with ammonia or acids

such as vinegar. Follow package directions when using laundry products. Incorrect usage can produce

poisonous gas, resulting in serious injury or death.

*Do not reach into the washer while parts are moving.

Before loading, unloading, or adding items, push in the

cycle selector knob and allow the drum to coast to a complete stop before reaching inside. Failure to follow

this warning can cause serious injury, fire, electric shock or death.

• Refer to INSTALLATION INSTRUCTIONS for detailed grounding procedures. Installation instructions are

packed in the washer for the installer's reference. If the washer is moved to a new location, have it checked and reinstalled by a qualified service technician. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Failure to follow this warning can cause seriousinjury, fire, electric

shock, or death.

• For personal safety, this appliance must be properly grounded. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

• The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shockhazard from this appliance.

• This washer must be plugged into a 120VAC, 60Hz grounded outlet. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

• Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

• Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

• Do not install on carpet. Install the washer on a solid

floor. Failure to follow this warning can cause serious leak damage.

• Do not remove the grounding prong. Do not use an adapter or extension cord. Plug into a grounded 3-prong outlet. Failure to follow these warnings can

cause serious injury, fire, electric shock, or death.

•The washer should always be plugged into its own

individual electrical outlet which has a voltage rating that matches the rating plate. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from

overheated wires.

*Never unplug your washer by pulling on the power

cord. Always grip plug firmly and pull straight out

from the outlet. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

*Immediately repair or replace all power cords that

have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. Consult with a qualified service technician. Failure to follow this warning can cause serious injury, fire, electric shock,

or death.

• When installing or moving the washer, be careful not

to pinch, crush, or damage the power cord. Failure

to follow this warning can cause serious injury, fire, electric shock, or death.

• The washer must be installed and electrically grounded by a qualified service technician in accordance with local codes to prevent shock hazard

and assure stability during operation.

*The washer is heavy. Two or more people may be

needed to install and move the appliance. Failure to do so can result in damage to property or serious

bodily injury.

• Store and install the washer where it will not be exposed to temperatures below freezing or exposed

to outdoor weather conditions. Failure to follow this warning can cause serious leak damage.

• To reduce the risk of electric shock, do not install the washer in humid spaces. Failure to follow this

warning can cause serious injury, fire, electric shock, or death.

•Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is

used near children. As children grow, teach them the proper, safe use of all appliances. Failure to comply with

these warnings could result in serious personal injury.

• Destroy the carton, plastic bag, and other packing materials after the washer is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight

chambers. Failure to comply with these warnings could

result in serious personal injury.

IMPORTANT: Please read carefully'.

• Keep laundry products out of children's reach. To

prevent personal injury, observe all warnings on product labels. Failure to comply with these warnings

could result in serious personal injury.

• Before your washer is removed from service or discarded, remove the door to the washing compartment to avoid the danger of children or small animals getting trapped inside. Failure to do so can result in serious personal injury or death.

TO CONNECT ELECTRICITY

Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check

with a qualified electrician or service technician if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance. If it does not fit the outlet, have a proper outlet installed by a qualified electrician. Failure to follow these warnings can cause serious injury, fire, electric shock, or death.

3-prong grounding type wall receptacle

Ensure proper

3-prong grounding plug

ground exists before use.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least

resistance for electric current. This appliance is equipped

with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes

and ordinances.

I KEY PARTS AND COMPONENTS

O ETERGENT DISPENSER

There are four compartments, one each for prewash, main wash, liquid bleach, and liquid fabric softener.

O ONTROL PANEL

The easy-to-read LED display shows cycle options, settings, cycle status, and estimated time remaining during

operation.

NOTE: Sensors in the washer automatically detect the size of the wash load to optimize washing time, based on the selected cycle and options.

O IRECT-DRIVE MOTOR

The direct-drive motor provides improved performance and reliability while increasing energy efficiency. (Motor is not visible.)

O ARGE-CAPACITY STAINLESS STEEL DRUM

The ultra-large stainless steel drum ofi:ers extreme durability and is tilted to improve efficiency and allow easier access for large items.

O ASY-ACCESS LOCKING DOOR

The extra-large door locks during operation. The door will not open until it is safe to do so.

O ILTER ACCESS PANEL

Provides easy access to the drain pump filter, which allows you to clean the filter or retrieve lost items without a

service call.

Cold and Hot Water Inlets

Power

Cord

LEVELING FEET

Four leveling feet (two in the front and two in the back) adjust to improve washer stability on uneven floors. Feet

are adjusted and locked in place using the adjusting wrench included with the washer.

O AGNETIC DOOR PLUNGER

Safely and conveniently keep the door ajar with the magnetic door plunger. The magnet keeps the door slightly open when the washer isn't in use to promote air circulation and allow the interior of the machine to dry. To use this feature, after the laundry has been removed, close the door just until it contacts the magnet.

Included Accessories

Non-skid pads Caps (4)

(for covering

shipping bolt holes)

Drain

Rear of Washer

NOTE: Bolts/Retainers MUST be removed prior to

I Shipping Bolts/Retainers (4)

operation. Keep for future use.

Hot and Cold Water Hoses Drain Hose Extension

Optional Accessories

Wrench (for removing Tie Strap

shipping bolts and (for securing

adjusting and drain hose) _tocking leveling feet) Wrench appearance may vary.

Elbow Bracket

(for securing

drain hose)

Pedestal

51042 (White)

51043 (Metallic Silver)

P/N 5215ER2002K

Stacking kit (For dryer)

D26 17013 (Chrome Look)

KEY DIMENSIONS AND SPECIFICATIONS

Description Front-Loading Washer Rated Voltage/Frequency 120VAC, 60Hz Dimensions 27 in. (W) X 29 3,,_in. (D) X 38 11/16in. (H), 51 in. (D, door open)

68.6 cm (W) X 75.6 cm (D) X 98.3 cm (H), 129.5 cm (D, door open)

Net Weight 196.2 Ib (89kg)

CHOOSE THE PROPER LOCATION

WARNING

oThis washer is heaw/. Two or more people are

required when moving and unpacking the washer. Failure to do so may result in damage to property or

serious bodily harm.

• Store and install the washer where it will not be exposed to temperatures below freezing or exposed

to outdoor weather conditions. Failure to follow this

warning can cause serious injury, fire, electric shock, or death.

• Properly ground the washer to conform with all

electric governing codes and ordinances. Failure

to follow this warning can cause serious injury, fire, electric shock, or death.

°To reduce the risk of electric shock, do not install the

washer in humid spaces. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•To ensure proper air flow, do not block the large

opening on the bottom of the washer with carpeting or other materials.

• Do not remove the ground prong. Do not use an adapter or extension cord. Plug into a grounded

3-prong outlet. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

NOTE: Installing the washer in a humid space, or installing or storing the washer where it will be exposed

to the weather or freezing temperatures, may result in

rust or other damage that is not covered by the product

warranty.

Power Outlet

•The power outlet must be within 60 in. (1.5 m) of either side of the washer.

•The appliance and outlet must be positioned so that the plug is easily accessible.

•Do not overload the outlet with more than one appliance.

•The outlet must be grounded in accordance with current wiring electric codes and regulations.

• Time-delay fuse or circuit breaker is recommended.

NOTE: It is the personal responsibility and obligation of the product owner to have a proper outlet installed by a qualified service technician.

CLEARANCES

21 1/4"

_(54 cm)_1

(75.6 ¢m) (10 cm)

"41

To ensure sufflcient clearance for water lines and airflow, allow minimum clearances of at least 1 in. (2.5 cm) at the sides and 4 in. (10 cm) behind the unit. Be sure to allow for wall, door, or floor moldings that may increase the required clearances.

J_I 29 3/4" _ J_ 4"

1 27 1

(2.5 cm) (68.6 cm) (2.5 cm)

Allow at least 22 in. (55.9 cm) in front of

the washer to open the door.

51"

(129.5 cm)

FLOORING

•To minimize noise and vibration, the washer MUST be installed on a solidly constructed floor. See the NOTE

to your right.

•Allowable slope under the entire washer is a maximum 1 in. difference from side to side or from front to back.

•Installing on carpeting and soft tile surfaces is not recommended.

•Never install the washer on a platform or weakly

supported structure.

NOTE: The floor must be strong and rigid enough to support the weight of the washer, when fully loaded, without flexing or bouncing. If your floor has too much

flex, you may need to reinforce it to make it more rigid. A floor that is adequate for a top-loading washer may not be rigid enough for a front loading washer, due to

the difference in the spin speed and direction. If the floor is not solid, your washer may vibrate and you may

hear and feel the vibration throughout your house.

UNPACKING AND REMOVING SHIPPING BOLTS

When removing the washer from the carton base, be sure to remove the foam drum support in the middle of the carton base. See drawing below.

If you must lay the washer down to remove the base

packaging materials, always protect the side of the washer and lay it carefully on its side. DO NOT lay the

washer on its front or back. To prevent internal damage during transport, the washer

is equipped with four shipping bolts and plastic retainers.

IMPORTANT:

•These shipping bolts and retainers MUST NOT be removed until just before moving the washer into its final position.

• These bolts and retainers MUST be removed before operating the washer.

• Failure to remove shipping bolts and retainers may cause severe vibration and noise, which can lead to

permanent damage to the washer.

NOTE: The power cord is secured to the back of the washer with a shipping bolt to help prevent operation with shipping bolts in place.

1. Starting with the bottom two shipping bolts, use the wrench (included) to fully loosen all four shipping bolts by turning them counterclockwise.

Shipping Bolts

2. Remove the bolt assemblies by wiggling them slightly while pulling.

3. Locate the four hole caps included in the accessory pack and install them in the shipping bolt holes.

NOTE: Save the bolt assemblies for future use. To prevent damage to internal components, DO NOT transport the washer without reinstalling the shipping bolts.

CONNECTING THE WATER LINES

• IMPORTANT: Use new hoses when installing the washer. Do NOT reuse old hoses.

• IMPORTANT: Use ONLY the inlet hoses provided with this washer. Aftermarket hoses are not guaranteed to fit or function correctly. Other hoses may not tighten correctly and could cause leaks. Subsequent damage to product or property will not be covered under the terms of the

product warranty.

•Water supply pressure must be between 14.5 psi and 116 psi (100-800 kPa). If the water supply pressure is more

than 116psi, a pressure reducing valve must be installed.

•Periodically check the hose for cracks, leaks, and wear,

and replace the hose if necessary.

•Make sure that the water lines are not stretched, pinched, crushed,or kinked.

•The washer should never be installed or stored in a location subject to freezing temperatures. Damage to the

water lines and internal mechanisms of the washer can

result. If the washer was exposed to freezing temperatures prior to installation, allow it to stand at room temperature

for several hours before use and check for leaks prior to operation.

3. Always run a gallon or two of water through each inlet hose to flush dirt, scale and other debris out

of the water lines. Doing so will help prevent future

problems with clogged filter screens, and will also

allow you to verify which hose is hot and which

is cold.

Rubber Seal Rubber Seal

Water Hose e_

(to water inlet Water Hos on washer) (to tap)

1. Inspect the threaded fitting on each hose and make sure there is a rubber seal in place in both ends.

Water Fa_

Cold Water

Water Inlet

Inlet

4. Attach the (red) hot water line to the hot water inlet on the back of the washer. Attach the (blue) cold water line

to the cold water inlet on the back of the washer.

Tighten the fittings securely.

NOTE: When installing the hoses onto the water inlet valves, be careful not to cross-thread the hose

fittings. DO NOT overtighten the hoses; this could cause damage to internal components, the valve or the hose

gasket. Overtightening could result in property damage from leaks.

2. Connect the water supply hoses to the HOT and COLD water faucets tightly by hand and then tighten another 2/3 turn with pliers.

CONNECTING THE DRAIN HOSE

•The drain hose should always be properly secured. Failure to properly secure the drain hose can result in

flooding and property damage.

•Do not install the end of the drain hose lower than 29

in. (73.7 cm) or higher than 96 in. (243.8 cm) above the bottom of the washer.

•The drain must be installed in accordance with any

applicable local codes and regulations.

•Make sure that the drain hose is not stretched, pinched,

crushed, or kinked.

NOTE:

A drain hose extension kit is

available if the drain hose isnot long enough. Do not extend the

drain hose more than 6 feet, as this will cause poor draining, which will result in poor wash

I Drain Hose Extension

P/N 5215ER20021<

and spin performance.

Option 1: Standpipe

Option 2: Laundry Tub

Utility Sink

The elbow bracket should be installed near the end of the drain hose. Hang the end of the drain hose over the

side of the utility sink. Use a tie strap to secure the drain hose in place.

Option 3: Floor Drain

Brooke

Strop

Hose

Install the end of the drain hose into the elbow bracket.

Do not extend the drain hose more than 4 inches past the end of the elbow bracket. Use a tie strap to secure the drain hose in place.

NOTE:

•Total height of the hose end should not exceed 96 in.

(243.8 cm) from the bottom of the washer.

•The drain hose should be inserted no more than 8-12

inches into the standpipe. Inserting the hose more than 8-12 inches can cause mold or microorganisms to

spread to the inside of the washer.

Drain Hose

Floor Drain

Insert the end of the drain hose into the floor drain. If possible, secure the hose to prevent it from moving or

coming out of the drain.

CONNECTING TO THE POWER SUPPLY

The washer should be plugged into a 120-VAC, 60-Hz grounded 3-prong outlet. Plug in the washer.

If the water valves and drain are built into the wall, fasten the drain

hose to one of the water hoses with the tie strap (ribbed side on inside).

Tie Strap

LEVELING THE WASHER

The drum of your new washer spins at very high speeds. To minimize vibration, noise, and unwanted movement, the floor must be a level, solid surface.

NOTE: Adjust the leveling feet only as far as necessary to level the washer. Extending the leveling feet more than necessary can cause the washer to vibrate.

NOTE: Before installing the washer, make sure that the floor is clean, dry and free of dust, dirt, water and oils so the washer feet cannot slide easily. Leveling feet that

move or slide on the floor can contribute to excess vibration and noise due to

poor contact with the floor. See

INSTALLATION OF NON-SKID PADS for more information.

NOTE: If a drip pan must be used, make sureto follow the

instructions provided with the drip pan and make sure the

leveling feet are adjusted for firm and even contact with the pan. Use of drip pans and failure to properly level the

machine may result in increased vibration and noise during operation.

All four leveling feet must rest solidly on the floor. Rock the washer from corner to corner to make sure that all

four leveling feet are in firm and even contact with the floor.

@ @ @ _ Level

3. Once the washer is level from side to side and front to back, use the adjusting wrench to tighten all four lock

nuts securely to prevent the legs from getting out of adjustment during operation. Make sure that all four leveling feet are in firm contact with the floor.

NOTE: To make sure that the washer is properly level, run the washer with a test load: place a medium-sized load

of laundry in the machine. Then, press POWER, select RINSE & SPIN, and press the START/PAUSE button.

See the following sections for additional information on cycle selection and operation. Verify that the washer does not rock or vibrate excessively during the spin cycle. If the

washer vibrates or shakes, adjust the leveling feet, while the washer is spinning, until the vibrations are reduced.

Leveling Feet

\ Leveling Feet j

1. Position the washer in its final location, taking special care not to pinch, strain, or crush the water and drain lines. Place a level across the top of the washer.

Raise Lower

2. Loosen the Iocknuts on all four leveling feet with the wrench until you can adjust the feet (wrench

appearance may vary). Use the wrench to turn the feet clockwise to raise the washer, and counterclockwise to lower the washer. Using a level to check, adjust the feet

until the washer is level from side to side and front to back. Make sure that all four feet are in firm contact with the floor.

INSTALLATION OF NON-SKID PADS (optional)

Some floor surfaces are too slippery to prevent the

washer from moving on the floor during heavily

unbalanced loads. While it is normal for an occasional load to be out of balance, excess noise and vibration can

result from the washer moving out of position. If these conditions are encountered, follow the instructions below for installation of the non-skid pads. These pads will help prevent the washer from moving during heavy, out of balance conditions, thereby reducing noise and vibration.

NOTE: The non-skid pads are included in the installation packet

Non-skid pads

This side up

_ Stick adhesive side to floor

move backing

:_ Place the pads under both front feet.

NOTE: If you are installing the washer on the optional pedestal, the washer's leveling feet should be fully retracted. Use the leveling feet on the pedestal to level the washer.

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read and follow this

entire Use & Care Guide, including the Important Safety Instructions, before operating this washer.

CONTROL PANEL FEATURES

i.............................

_ Kenrnore Connect * Vibration Guard

O POWER (ON/OFF) BUTTON

Press to turn the washer ON or OFF.

NOTE: Pressing the POWER button during a cycle will cancel that cycle and any load

settings will be lost. The door will unlock after a brief pause, unless the water level or temperature is too high.

CYCLE SELECTOR KNOB

Turnthis knob to select the desired cycle. Once the desired cycle has been selected, the standard presets will appear in the display. These settings can be adjusted using the cycle modifier buttons any time before starting the cycle.

Wash Temp i Spin Speed i Soil Level Chime

[ 7

O CYCLE MODIFIER BUTTONS

Use these buttons to adjust the settings for the selected cycle. The settings light up above the

buttons to show the current selection.

O SPECIAL CYCLE AND OPTION BUTTONS

These buttons are used to activate special cycles or options.

O TIME AND STATUS DISPLAY

The display shows the cycle status, door lock status and estimated time remaining.

O START/PAUSE BUTTON

Press this button to start the selected cycle. If the washer is running, use this button to pause

the cycle without losing the current settings. NOTE: If you do not press the START/PAUSE

button within four minutes of selecting a cycle, the washer automatically turns OFF.

NOTE: To protect your clothing, not all settings are available on all cycle selections.

1 OPERATING THE WASHER

POWER

O SORT LAUNDRY AND LOAD WASHER

Sort laundry by fabric type, soil level, color and load size, as needed. Open the door and load selected items into the

washer.

TURN ON THE WASHER

Press the POWER button to turn ON the washer. The lights

around the cycle selector knob will illuminate and a chime will sound.

Normal

Bulky

Heavy Duty

Whites

START I PAUSE

SELECT A CYCLE

Turn the cycle selector knob in either direction to select the desired cycle. The preset Wash Temperature, Spin Speed, Soil

Level, and Option settings for that cycle will be shown.

SELECT CYCLE MODIFIERS & OPTIONS

Default settings for the selected cycle can now be changed if

desired. Use the cycle modifier buttons.

NOTE: To protect your fabrics, not all modifiers are available on all cycles. Cycle options can also be added by using the option buttons.

NOTE: Not all options are available on all cycles. A different chime will sound and the LED will not come on if the selection

is not allowed.

ADD DETERGENT

Add High-Efficiency (HE) detergent to the detergent dispenser drawer. For proper wash performance, always measure the

detergent using the measurements provided by the detergent

manufacturer.

BEGIN CYCLE

Pressthe START/PAUSE button to begin the cycle. The door will

lock, and the washer will briefly tumble the load without water to measure its weight. Once the weight of the load is measured, the washer will begin the selected wash cycle.

Pressing the START/PAUSE button during the cycle will pause the cycle and the door will unlock. Press the START/PAUSE

button again to resume the wash cycle.

CYCLE GUIDE _ -- Available Option

The cycle guide below showsthe default settings,available options and recommended fabric types

for each cycle. Allowable modifier adjustmentsare shown below the default setting for each cycle. Default Setting

Cotton, linen,

Normal towels, shirts,

Bulky blankets and

sheets, jeans, mixed loads

Large items such as

comforters

Heavy Heavily

Duty

Whites

soiled cotton fabrics

Heavily to normally Warm

soiled white Tap Cold cottons Cold

Extra High

Medium

Low

No Spin

NOTE:

•To protect your garments, not every wash temperature, spin speed, soil level, or option is available with every cycle. A chime will sound and the LED will not light if the selection is not allowed.

•The washer automatically adjusts the wash time for the amount of laundry, water pressure, water heating time and other operating conditions.

• These cycles use various wash motions to enhance cleaning and/or fabric care performance. The wash motions may sound difl:erent at difl:erent stages of the wash cycle. This is normal.

CYCLE GUIDE (continued) _ = Available Option

The cycle guide below shows the default settings, available options and recommended fabric types for each cycle. Allowable modifier adjustments are shown below the default setting for each cycle. _:iii:i:i:i:i:i= Default Setting

Express Lightly soiled

Wash clothing and

Cold Clean

Delicates

Rinse and Loads that Extra High

Spin only need to Medium

small loads

Small loads of cotton,

linen, towels, shirts, sheets,

jeans, mixed

loads

Dress shirts/ blouses,

nylons,sheeror lacy garments

be rinsed Cold Low

No Spin

NOTE:

• To protect your garments, not every wash temperature, spin speed, soil level, or option is available with every

cycle. A chime will sound and the LED will not light if the selection is not allowed.

•The washer automatically adjusts the wash time for the amount of laundry, water pressure, water heating time and other operating conditions.

•These cycles use various wash motions to enhance cleaning and/or fabric care performance. The wash motions may sound difl:erent at difl:erent stages of the wash cycle. This is normal.

SORTING WASH LOADS

Fabric Care Labels

Many articles of clothing include a fabric care label.

Using the chart below, adjust the cycle and option

selections to care for your clothing according to the

manufacturer's recommendations.

Fabric Care Labels

Machine

wash

cycle

Normal Permanent press/ Gentle/

wrinkle resistant delicate

H h Donotwash Donot wring

Water • • • • • •

temperature Hot Warm Cold/cool

Bleach symbols _ /A/_A

Any bleach Only non-chlorinebleach Do notbleach

(when needed) (when needed)

Grouping Similar Items

For the best washing results, and to reduce the possibility of damage to clothing, care should be taken to sort the clothing into loads that are made up of similar items. Mixing different fabric types and/or soil levels can result

in poor wash performance, color transfer or discoloration, fabric damage or linting. Fabrics should be sorted into groups as described below.

Loading the Washer

• Check all pockets to make sure that they are empty.

Items such as clips, matches, pens, coins, and keys can

damage both your washer and your clothes.

•Close zippers, hooks, and drawstrings to prevent these items from snagging or tangling on other clothes.

• Pretreat heavily stained areas for best results.

•Combine large and small items in a load. Load large items first.

• Large items should not be more than half of the total wash load.

•The drum should not be tightly packed with items. The door of the washer should close easily.

•To prevent an out-of-balance load, do not wash single items. Add one or two similar items to the load.

Large, bulky items, such as a blanket, comforter, or

bedspread, should be washed individually.

• Do not wash or spin waterproof items, such as rain coats, sleeping bags, etc.

• When unloading the washer, check under the door seal for small items.

NOTE: Make sure that the door seal area isclear when

closing the door. Overloading the washer can cause items to get caught between the door and the seal. This can damage both the items and the seal.

Colors

Sort articles by color. Wash dark clothes together in a separate load from light colors or whites. Mixing dark

clothes with light clothes can result in dye transfer or discoloration of the lighter clothes.

Soil Level

Wash heavily soiled clothing together. Washing lightly soiled clothing in the same load with heavily soiled clothing could result in poor wash performance for the

lightly soiled clothing.

Fabric Type

Delicate articles should not be mixed with heavier or

sturdier fabric types. Washing delicates in a load with

heavy fabrics can result in damage to the more delicate

fabrics. Washing heavier fabrics in a delicate load can

result in poor wash performance for the heavier fabrics

and possible damage to the delicates.

Lint Type

Some fabrics attract and bind lint to them while others give off lint in the laundry process. Avoid mixing these

lint collectors and lint producers in the same load. Mixing these fabrics will result in pilling and linting on the lint collectors. (For example, lint collector - knit sweater; lint

producer- terry cloth towels.)

• DO NOT OVERLOAD THE DRUM

• MAKE SURE CLOTHING IS NOT

CAUGHT IN THE DOOR GASKET

Sort Laundry...

by Colors Whites

Lights Darks

by Soil Heavy

Normal Light

by Fabric Delicates

Easy Care

Sturdy

by Lint Lint Producer

Lint Collector

1 ABOUT THE DISPENSER DRAWER

The automatic dispenser consists of four compartments which hold:

•Liquid chlorine bleach.

•Liquid fabric softener.

•Liquid or powdered detergent for prewash.

•Liquid or powdered detergent and color-safe bleach for main wash.

Liquid Chlorine Bleach

Compartment

Main Wash Detergent Compartment

Liquid Fabric Softener

Compartment

Liquid

lent

Cup

Detergent Compartment

Pre-Wash Detergent Compartment

Add liquid or powdered detergent to this compartment when using the Pre-Wash option. Always use liigh-

Efficiency (liE) detergent with your washing machine.

The amount of detergent added for the Pre-Wash option should be 1/2the amount recommended for the

main wash cycle. For example, if the main wash cycle requires 1/2measure of detergent, add 1/4measure to the

Pre-Wash compartment. NOTE: When using the Pre-Wash option, if using liquid

detergent for the main wash, the liquid detergent cup accessory must be used in the main wash dispenser. This

will prevent the main wash liquid detergent from being dispensed immediately.

Main Wash Detergent Compartment

This compartment holds laundry detergent for the main wash cycle. The detergent is added to the load at the

beginning of the cycle. Always use High-Efficiency (HE) detergent with your washing machine. Either powdered or liquid detergent may be used.

Never exceed the manufacturer's recommendations when adding detergent. Using too much detergent can

result in detergent buildup in clothing and the washer.

NOTE: Liquid or powdered color-safe bleach may be added to the main wash compartment with detergent of the same type. DO NOT add liquid or powdered color-safe bleach to the bleach dispenser. DO NOT mix

liquid and powdered cleaning agents within the same compartment.

Liquid Bleach Compartment

This compartment holds liquid chlorine bleach, which is dispensed automatically at the proper time during the wash cycle.

• Do not add powdered or liquid color-safe bleach to this compartment. The bleach compartment is designed to dispense liquid chlorine bleach only. Powdered or liquid color-safe bleach will not dispense properly.

•Always follow the manufacturer's recommendations when adding bleach. Do not exceed the maximum fill line since this can cause the bleach to be dispensed immediately, causing damage to fabrics. Using too much bleach can damage fabrics.

• Never pour undiluted liquid chlorine bleach directly onto the load or into the drum. Fabric damage can occur.

Fabric Softener Compartment

This compartment holds liquid fabric softener, which is automatically dispensed during the final rinse cycle.

Never exceed the manufacturer's recommendations when

adding softener. Using too much fabric softener can result in buildup in clothing and the washer. Either powdered or liquid fabric softener may be used.

•Always follow the manufacturer's recommendations when adding fabric softener. Do not exceed the maximum fill line. Using too much fabric softener may

stain clothes.

• Dilute concentrated fabric softeners with warm water.

Do not exceed the maximum fill line.

*Never pour fabric softener directly onto the load or

into the drum.

DETERGENT AND DISPENSER USE

A Word About Detergents

High-Efficiency (HE) detergents produce fewer suds,

dissolve more efficiently to improve washing and rinsing

performance, and help to keep the interior of your

washer clean. Using detergent that is not HE may cause oversudsing and unsatisfactory performance which could result in error codes, cycle failure, and

machine damage.

---_ Maximum __[_l ormal Load Amount

Liquid Powdered

Detergent Detergent

For proper wash performance, always measure the detergent using the measurements provided by the detergent manufacturer.

The normal amount of HE detergent needed, for average

loads, is less than 1/2of the recommended maximum. Use less detergent for soft water, light soil or smaller

loads. Never use more than the maximum amount recommended by the detergent manufacturer.

Detergent Amount

For proper wash performance, always measure the detergent using the measurements provided by the detergent manufacturer.

Filling the Dispenser

To add detergent, bleach, and fabric softener to the automatic dispenser:

Open the dispenser drawer.

Load the laundry products into the

appropriate compartments.

Close the drawer before starting the cycle.

NOTE: It is normal for a small amount of water to remain in the bleach and softener compartments at the

end of the cycle.

IMPORTANT: Do not place or store laundry products, such as detergent, bleach, or liquid fabric softener, on top

of your washer or dryer. Wipe up any spills immediately. These products can damage the finish and controls.

Designed to use only

High-Efficiency (HE) detergent

IMPORTANT: Your washing machine is designed for use

with only High-Efficiency (HE) detergents. HE detergents are formulated specifically for front-load washers and contain suds-reducing agents. Always look for the HE symbol when purchasing detergent.

IMPORTANT: Not all detergents are the same. Pay careful attention to the amount of detergent used to avoid oversudsing, poor rinsing and detergent buildup in clothing, and residue buildup that can contribute to odors

in the machine. NEVER use a cup or scoop other than the one supplied by the manufacturer of the detergent you are using. Never use more than the maximum amount of detergent recommended by the manufacturer.

Always measure the detergent amount. While HE detergents are designed for this type of washing

machine, be careful when measuring the detergent. For

most normal loads, no more than 1/4 to 1/2 of cap or scoop of HE detergent should be used.

NOTE: Extra care must be exercised when using 2X and 3X concentrated detergents because even a little bit extra can contribute to the problems mentioned above.

NOTE: Detergents designated as HE compatible may not

provide optimal results.

MAGNETIC DOOR PLUNGER

Safely and conveniently secure the door slightly ajar with the magnetic door plunger. This will promote air circulation and allow the interior of the machine to dry.

To use this feature, remove the clean laundry then posi- tion the door so that the door is almost closed. When

the magnetic door plunger comes into contact with the metal washer cabinet, it will secure the door slightly open, allowing the interior of the washer to dry.

TIME AND STATUS DISPLAY

The time and status display shows the estimated time remaining, cycle progress, and door lock status.

IWashTem0ISpnSpeed]SoiLeve[Chime1

A_I Cold Rinses

O ESTIMATED TIME REMAINING _i

When the START/PAUSE button is pressed, the washer will automatically detect the load size for

cycles that use load sensing. The control will then optimize the wash and rinse times, based on the se- lected cycle, modifiers and options. When the load size has been determined, the display will change from dashes (- - -) to the estimated time for that cycle. For non-load sensing cycles, the estimated time will display when the cycle is selected.

NOTE:

•The time shown is only an estimate. For example, the time displayed may pause for a period of time while the machine is heating the water or balancing the load. Under certain conditions, the machine can pause for extended periods of time.

•Estimated time is based on normal operating conditions. Several external factors (load size, room temperature, incoming water temperature, etc.) also affect the length of estimated time vs. actual time.

O LOAD-SENSING INDICATOR

At the beginning of cycles that use the load sensing feature, the LOAD SENSING light will blink while the load size is being measured. Once the size has been determined, the control adjusts the cycle for optimum performance. Estimated time remaining will not display until the load size has been determined, and may be different for each load.

CYCLE STATUS INDICATOR These status LEDs illuminate to indicate which

stage of the cycle is currently running. A blinking light indicates the active stage of the cycle. When that stage is complete, the light will remain steady.

DOOR LOCI( INDICATOR

Indicates that the door is locked. The washer door will lock while the washer is operating. The door can

be unlocked by pressing START/PAUSE to pause the washer.

NOTE:

•If the temperature in the washer is too high, the door cannot be unlocked until the washer

has cooled.

•If the water level is too high, the door will not unlock. To drain the water, press POWER, then press the SPIN SPEED button without selecting a cycle. Press START/PAUSE and the water will drain and the clothes will spin out. Do not try to force the door open, as it will damage the door.

CYCLE MODIFIER BUTTONS

Each cycle has default settings that are selected

automatically. You may also customize these settings

using the cycle modifier buttons. Press the button for the desired modifier until the indicator light for the desired value is lit. The washer automatically adjusts the water

level for the type and size of wash load for best results and maximum efficiency. Due to the high-efficiency

nature of this product, water levels may be much lower than expected. This is normal operation and cleaning/

rinsing performance will not be compromised.

[Washmemp[S0inSpee l[

Atl CoId Rinses

NOTE: To protect your garments, not every wash temperature, spin speed, soil level, or option is available with every cycle. A chime will sound and the LED will not

light if a selection is not allowed.

Soil Level

Chime

O WASH TEMP

Wash Temp selects the wash and rinse temperature combination for the selected cycle. Press the Wash

Temp button until the indicator light for the desired setting is lit.

*Select the water temperature suitable for the type

of load you are washing. Follow the garment fabric care labels for best results.

•Warm rinses are regulated at approximately 86°F (30°C).

•Warm rinses leave the clothes dryer than cold rinses, but will result in increased energy

consumption and greater wrinkling of clothes.

•Cold rinses use less energy. The actual rinse temperature depends on the temperature of the

cold water at the faucet.

O SPIN SPEED

Higher spin speeds extract more water from clothes, reducing drying time and saving energy.

Press the SPIN SPEED button until the desired speed is selected. Some fabrics, such as delicates, require a slower spin speed. To protect your clothing, not all spin speeds are available for all cycles.

The Drain & Spin cycle:

1. Pressthe POWER button to turn ON the washer.

2. Press the SPIN SPEED button to select the desired spin speed. For drain only, select the

NO SPIN option.

3. Press the START/PAUSE button. The water will drain and the clothes will tumble before

the spin routine begins.

SOIL LEVEL

Adjusting the soil level setting will modify the cycle to allow more time for heavily soiled clothes or less

time for lightly soiled clothes. Pressthe SOIL LEVEL

button until the desired soil level is selected.

CHIME

Press repeatedly to adjust the volume of the chime and keypad tones. You may turn the end-of-cycle chime and keypad tones ON or OFF with the CHIME

button.

+ 44 hidden pages