Kenmore 580.72127200, 580.72087200 Owner's Manual

Owner's Manual Manual del Propietario

THROUGH-THE-WALLAIRCONDITIONER ACONDICIONADODEAIREA TRAVESDEPARED

ModeI, Modelo 580.72087200 580.72107200 580.72127200

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.com

TABLE OF CONTENTS ........................2

Features ................................................. 13

WARRANTY ..............................................2

SAFETY .....................................................3

ImportantSafety Instructions...................... 3

ELECTRICAL REQUIREMENTS .......4

INSTALLATION ........................................5

Installation Requirements ......................... 5

Installation ................................................ 6

Procedure A ............................................. 7

Procedure B ............................................. 9

Procedure C ........................................... 11

OPERATION ...........................................12

How and Why ......................................... 12

Normal Sounds ...................................... 12

Capacity and Running Time ................... 12

Using the Air Conditioner ....................... 13

Air Conditioner Features ........................ 14

MAINTENANCE .....................................16

Air Filter Cleaning ................................... 16

Air Conditioner Cleaning ........................ 16

How to Remove the Front Grille ............. 16

How to Replace the Front Grille ............. 16

TROUBLESHOOTING .........................17

Before Calling for Service ...................... 17

ESPANOL ................................................18

MASTER PROTECTION

AGREEMENTS ......................................35

SERVICE NUMBERS ............ Back Cover

FULL ONE YEAR WARRANTY ON THROUGH-THE-WALL AIR CONDITIONER

For one year from the date of purchase, when this air conditioner is operated and maintained for

normal room cooling according to instructions in this owner's manual, Sears will repair this air conditioner, free of charge, if defective in material or workmanship.

WARRANTY SERVICE IS AVAILABLE BY

CONTACTING SEARS SERVICE AT 1-800-4-MY-HOME ®.

This warranty applies only while this product is in

use in the United States.

This warranty gives you specific legal rights, and

you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D/817WA,

Hoffman Estates, IL 60179 U.S.A.

-2-

IMPORTANT SAFETY INSTRUCTIONS

The safety instructions below will tell you how to use your room air conditioner to avoid harm to yourself or damage to your ROOM AIR CONDITIONER.

V!_W:_:t_II_[_FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Read product labels for flammability and

other warnings.

PREVENT ACCIDENTS

To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner, follow

basic precautions, including the following:

• Be sure the electrical service is adequate for the model you have chosen.

• If the air conditioner is to be installed in a window, you will probably want to clean both sides of the glass first. If the window is a triple-track type with a

screen panel included, you may want to remove the screen completely before installation.

• Be sure the air conditioner has been securely and correctly installed according to the instructions in this manual.

Save this manual and installation instructions for possible future use in removing or reinstalling this

unit.

• Use gloves when handling the air conditioner. Be careful to avoid cuts from sharp metal fins on

front and rear coils.

V!_W,.1;i_ll_[dELECTRICAL INFORMATION

The complete electrical rating of your new room air conditioner is stated on the serial plate. Refer to the

rating when checking the electrical requirements.

• Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards.

• Your air conditioner must be plugged into a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately

grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle.

• Do not run air conditioner with packing sheet of the back of the sleeve, and packing corner and

blue tape of the air conditioner. This could result in mechanical damage within the air conditioner.

• Do not use an extension cord or an adapter plug.

_ Avoid fire hazard or electric shock.

Do not use an extension cord or an adapter plug. Do not remove any prong from the power cord.

Grounding type

wall receptacle

grounding plug

Do not under any circumstances cut, remove, or bypass the grounding prong

from this plug.

ENERGY SAVING IDEAS

• The capacity of the room air conditioner must fit the room size for efficient and satisfactory

operation.

• install the room air conditioner on the shady side of your home. A window that faces north is best

because it is shaded most of the day.

• Do not block air flow inside with blinds, curtains, or furniture; or outside with shrubs, enclosures, or other buildings.

• Close the floor and wall registers and the fireplace damper so cool air does not escape up the chimney and into the duct work.

• Keep blinds and drapes in other windows closed during the sunniest part of the day.

• Clean the air filter as recommended in the

MAINTENANCE section of this manual.

• Proper insulation and weather stripping in your home will help keep warm air out and cool air in.

• External house shading with trees, plants or awnings will help reduce the air conditioner's work

load.

• Operate heat producing appliances such as ranges, washers, dryers, and dishwashers during the coolest part of the day.

-3-

OBSERVEALL LOCAL CODES AND

ORDINANCES. DO NOT, UNDER ANY CIRCUMSTANCES,

REMOVE THE POWER SUPPLY CORD GROUND PRONG.

ELECTRICAL GROUND IS REQUIRED ON THIS APPLIANCE.

A 208/230-volt and 115-volt 60 Hz, AC only,

15A fused and properly grounded electrical supply is required. A time delay fuse or time delay circuit breaker is recommended. Use a dedicated circuit, serving only this appliance.

DO NOT USE AN EXTENSION CORD. RECOMMENDED GROUNDING METHOD

For your personal safety, this appliance must be grounded. This appliance has a power

supply cord with a 3-prong grounding plug. To minimize possible shock hazard, the cord must

be plugged into a mating grounding type wall receptacle and grounded in accordance with

the National Electrical Code (ANSt/NFPA 70) latest edition and all local codes and

ordinances. If a mating wall receptacle is not available, it is the personal responsibility and

obligation of the customer to have a properly grounded 3-prong wall receptacle installed by a

qualified electrician.

Electrical Shock Hazard Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result

in death, fire, or electrical shock.

Ground prong I/! _ 'fl

/ 3-prong

_..k I \"--J I grounding

,J-prong _ I _ ] type wall

gg.rounalng k _'T'F I receptacle

Power_ "_

supply

cord

-4-

INSTALLATION REQUIREMENTS

If you use an existing wall sleeve, you should

measure its dimensions. install the new air conditioner according to these

installation instructions to achieve the best performance. All wall sleeves used to mount the

new air conditioner must be in good structural

condition and have a rear grille to securely attach the new air conditioner. (FIG. 1)

With the Kenmore folding sleeve, you can

maintain the best performance of the new air

conditioner.

19-2//32"

(499 mrn)

Air Conditioner

ELECTRICAL SERVICE

Check your available electrical service. The power

supply available must be the same as that shown on the unit nameplate (found on left side of cabinet).

All models are equipped with a 3-prong service plug to provide proper service and safe positive grounding. Do not change plug in any way. Do not

use an adapter plug. If your present wall outlet does not match your plug, call a qualified electrician to

make the necessary corrections. SAVE CARTON

for storage and this OWNER'S MANUAL for future

reference. The carton is the best way to store unit

during winter or when not in use.

(626 ram)

6mrn)

FIG. !

INSTALLATION HARDWARE

j 2 Size options

; s,zeo t,on

ITEM NAME OF PARTS Q'TY

(1_ PLASTIC GRILLE 1

HORIZONTAL iNSULATION STRIPS 2 AROUND INSULATION STRIPS 2

suPPORTBLOCK 2

BAFFLE 1

_6_ TRIM FRAME 2

SHIM 2

_8_ PLASTIC NUTS AND WASHER SCREWS 4

To avoid riskof personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:

•Air conditioners covered in this manual pose an excessiveweight hazard. Two or more people

are needed to move and install the unit.

To prevent injury or strain, use proper lifting and

carrying techniques when moving unit.

• Carefully inspectlocation where air conditioner

will be installed. Be sure itwill support the weight of the unitover anextended periodof time.

• Handle air conditioner with care. Wear protective gloves whenever lifting or carryingthe

unit. AVOID the sharp metal fins offront and rear coils.

• Make sure air conditioner does not fall during installation.

REQUIRED TOOLS:

•Tight Fitting gloves

•Standard screwdriver

•Phillips screwdriver

• Pliers

• Sharp knife

-5-

• 3/8-inch open end wrench or adjustable

wrench

• 1/4-inch hex socket

and ratchet

• Tape measure

• Electric drill

• 1/4-inch drill bit

INSTALLATION

We strongly recommend the removal of the

oldwall sleeve and the installationof a new Kenmore folding Wall Sleeve,

If you decide to keep the existing wall sleeve,

you haveto redirect the louvers at the back of the wall sleeve illustration. The use of pliers is

recommended. If you DO NOT redirect, you run

the risk of poor performance or product failure. This is not covered under the terms of the

Kenmorewarranty.

• Pick a location which will allow the conditioned air to blow into the area you want. Good installation with

special attention to the proper position of the unit will

lessen the chance that service will be needed.

• Assemble the folding sleeve for this unit according to

the instructions provided.

ITEMS IN INSTALLATION HARDWARE

You may not need all parts in the kit. Discard unused

_arts

ITEM (inches)

Plastic grille Horizontal insulation Strips

Around insulation Strips

Support Block 13/4x 13/8 x 45/18

Baffle 14 x 41/2 x 1/8

Shim 13 x 1 x 3/4 Trim Frame Washer Screw

Nuts(Plastic)

263/4 x 161/2

13/8x 5/8x 273/18 13/8x 13/8 x 273/18

13/8X 3/4X 611/2 13/8X 13/8 X 611/2

Qty.

1 1

2 2

4 4

HOW TO INSTALL

NOTE: All wall sleeves used to mount the new Air

Conditioner must be in sound structural condition and have a rear grille that securely attaches to

sleeve, or rear flange that serves as a stop for the Air Conditioner,

I_11 Remove old air conditioner from existing wall

sleeve.

I_j Clean the interior of an existing sleeve.

(Do not disturb seals.)

D Wall sleeve must be securely fastened in wall

before installing the air conditioner. Use the nails or screws through sleeve into wall, if needed. Repaint sleeve if needed.

I_ Prepare the wall sleeve for installation of the

unit. If you plan to use your existing wall sleeve, and it is not Kenmore, use procedure B or C

below.

Procedure Brand Depth(inches)

A Sears/Kenmore 16-23/32

White-Westinghouse

Frigidaire Carrier 16, 17-1/2

(52F series)

B General Electric

/Hotpoint

Whirlpool 17-1/8 or 23 Carrier (51S series) 18-5/8

Fedders/Emerson

Q Install new unit into wall sleeve. CAUTION: When installation is completed,

replacement unit MUST have a rearward slope as shown.

Emerson/Fedders 15 Friedrich 16-3/4

or 22

16-7/8

16-3/4

or 19-3/4

O Identify the existing wall sleeve before installing

the unit from the listed below.

Brand

White-Westinghouse

Frigidaire Carrier (52F series) General Electric

/Hotpoint

Whirlpool 25-7/8

Fedders/Emerson 27

Sears/Kenmore 25-7/8

Emerson/Fedders 26-3/4 Carrier (51S Series) 25-3/4

Friedrich 27

Wall Sleeve Dimensions (inches)

Width

25-1/2

Height Depth

15-1/4 16, 17-1/2

15-5/8 16-7/8

16-1/2

16-3/4 16-3/4

15-17/32 16-23/32

15-3/4 15 16-7/8 18-5/8

16-3/4 16-3/4

or 22

17-1/8

or 23

or 19-3/4

UNIT Wall Sleeve

1/4"__j

FIG. 2

-6-

PROCEDURE A

D Install the new unit into the wall sleeve.

O If you are using a new Kenmore folding sleeve

with your unit, skip to step 3. Otherwise, install the plastic grille from the kit. Cut the plastic

grille to 25-1/2" wide and 15-1/4" high. Place the plastic grille to the inside of the wall sleeve at the rear flange.

FIG. 3

B Fasten the 4 washer screws to secure the grille

to the wall sleeve. If you need plastic nuts to mount plastic grille to the inside of the wall sleeve, there are plastic nuts in the installation

kit. The nuts are installed from the inside of the sleeve and are pressed into the square holes of the rear flanges.

_41To assemble trim, snap the tab of each piece

into the slot of the other piece as shown below. Slide trim over the front of the air conditioner

until trim is flush with sleeve as shown below.

Trim (2 ea)

Wall

_1 Remove the backing from the Horizontal

Insulation strip 13/8X 3/8X 273/16 and attach that to the inside bottom of the sleeve as shown

below. Remove the backing from the Around Insulation strip 13/8X 3/4X 611/2 and attach that

to the inside front of the sleeve as shown below.

FIG. 6

FIG. 4

•Air conditioners covered in this manual pose an excessive weight hazard. Two or more

people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.

•When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and

rear coils.

• Make sure air conditioner does not fall during

removal.

FIG. 5

-7-

PROCEDURE B

H Redirect the louvers at the back of the wall

sleeve to 60 ° angle as shown in the FIG 7. The use of pliers is recommended.

7 51/6"

_6_ 0°

Rear Louvers

(Top View)

FIG. 7

_lf the wall sleeve already has a rear grille, skip

to step 4. If the wall sleeve does not have a rear grille or Iouvered panel, install the plastic grille

from the kit. Cut the plastic grille to 25-1/2" wide and 15-1/4" high. Place the plastic grille to the

inside of the wall sleeve at the rear flange.

_J Remove the backing from the Horizontal

insulation strip 13/8 x 5/8 x 273/16 and attach that

to the inside bottom of the sleeve as shown

below. Remove the backing from the Around insulation strip 13/8 x 3/4 x 611/2 and attach that to

the inside front of the sleeve as shown below.

FIG. 10

_Jlf the depth of your existing wall sleeve is less

than or equal to 18", skip to step 7. Otherwise,

cut the baffles and the support blocks according

to length "A" in the table below.

Depth"D"oftheexisting wallsleeve(inches)

18 <D _<18-5/8

18-% <D_<19-3/4

19-3/4<D _<22

Length"A"

(inches)

3/4

1-3/4

_ upport

Block

_[_ Baffle

FIG.11

Place the plastic grille

_J Fasten the 4 washer screws to secure the grille

to the wall sleeve. If you need plastic nuts to mount plastic grille to the inside of the wall sleeve, there are plastic nuts in the installation

kit. The nuts are installed from the inside of the sleeve and are pressed into the square holes of

the rear flanges.

Fasten the screws

FIG. 8

FIG. 9

r_ Remove the backing from the support blocks

and attach them to the inside of the wall sleeve as shown FIG 8. Slide the baffle into slots of the

support blocks.

Wall

Sleeve

H Install the new unit into the wall sleeve.

-8-

(7 5Sl6")

Support

Block

FIG. 12

PROCEDURE B

_JTo assemble trim, snap the tab of each piece

into the slot of the other piece as shown below. Slide trim over the front of the air conditioner

until trim is flush with sleeve as shown below.

Wall

FIG. 13

•Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.

• When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and

rear coils.

• Make sure air conditioner does not fall during removal.

-9-

PROCEDURE C

H Redirect the louvers at the back of the wall

sleeve to 60 ° angle as shown in the FIG 14. The use of pliers is recommended.

7 13,/6 **

Lt0°

Rear Louvers

(Top View)

FIG. 14

_J Remove the backing from the Horizontal

insulation strip 13/8 x 13/8 x 273/16 and attach that

to the inside bottom of the sleeve as shown

below. Remove the backing from the Around insulation strip 13/8 x 13/8 x 611/2 and attach that

to the inside front of the sleeve as shown below.

I_lf the wall sleeve already has a rear grille, skip

to step 4. If the wall sleeve does not have a rear grille or Iouvered panel, install the plastic grille

from the kit. Cut the plastic grille to 26-1/2" wide and 15-1t2" high. Place the plastic grille to the

inside of the wall sleeve at the rear flange.

Place the plastic grille

I[_ Fasten the 4 washer screws to secure the grille

to the wall sleeve. If you need plastic nuts to mount plastic grille to the inside of the wall

sleeve, there are plastic nuts in the installation kit. The nuts are installed from the inside of the

sleeve and are pressed into the square holes of the rear flanges.

FIG. 15

FIG. 17

If the depth of your existing sleeve is less than

or equal to 18", skip to step 7. Otherwise, cut the baffles and the support blocks according to

Length "A" in the table below.

Depth"D"of the existing wailsleeve(inches)

18 <D_<18-%

18-5/8<D <19-3/4

19-3/4<D <_22

r_ Remove the backing from the support blocks

and attach them to the inside of the wall sleeve as shown FIG 19. Slide the baffle into slots of

the support blocks

Length"A"

(inches)

3/4

1-3/4

_ upport

Block

_ Baffle

FIG. 18

13_/6" )

Wall

Sleeve

Fasten the screws FIG. 16

-10-

PROCEDURE C

W Remove the backing from the 13" shim strips

and attach them as shown below in Fig. 21. The higher portion of shim is to be placed in front of the rib on the base of wall sleeve.

h'0h E--' 'I'"0h

FIG. 20

FIG. 21

_r_ Install the new unit into the wall sleeve

_"_To assemble trim, snap the tab of each piece

into the slot of the other piece as shown below. Slide trim over the front of the air conditioner

until trim is flush with sleeve as shown below.

Trim (2 ea)

Wall

[!_ [_f_,_liI [.] _I

• Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.

• When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and

rear coils.

• Make sure air conditioner does notfall during removal.

-11-

FIG. 22

+ 25 hidden pages