Kenmore 146.29164310 Owner's Manual

Use & Care Guide

Manual de Uso y Cuidado

English / Espa_ol

Models/Modelos: 146.29163310/146.29164310/146.29162310

Items / Arficulos: 640-05280660-1/640-05280661-9/640-05280658-5

I<enmore Elite

P/N 30800317

Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com www.sears.com

www.kmart.com

Pro

gas de p *quSdo

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department.

1. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of

this or any other appliance.

2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

Installation Safety Precautions

• Please read this User's Manual in its entirety before using the grill.

• Failure to follow the provided instruction can result in

seriously bodily injury and!or property damage.

• Some parts of this grill may have sharp edges. Please wear suitable protective gloves.

• Use grill, as purchased, only with LP (propane) gas and the

regulator/valve assembly supplied.

• Grill installation must conform with local codes, or in their absence of local codes, with either the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2, or the Standard for Recreational

Cehicles, ANSI A 119.2/NFPA 1192, and CSA Z240 RV

Series, Recreational Vehicle Code, as applicable.

• All electrical accessories (such as rotisserie) must be electrically grounded in accordance with local codes, or

National Electrical Code, ANSI / NFPA 70 or Canadian Electrical Code, CSA C22.1. Keep any electrical cords

and/or fuel supply hoses away from any hot surfaces.

• This grill is safety certified for use in the United States and/or Canada only. Do not modify for use in any other

location. Modification will result in a safety hazard.

IMPORTANT: This grill is intended for outdoor use only and is not intended to be installed in or on recreational vehicles or

boats.

Call Grill Service Center For Help And Parts

If you have questions or need assistance during assembly,

please call 1-888-287-0735. You will be speaking to a representative of the grill manufacturer and not a Sears

employee. To order new parts call Sears at 1-800-4-MY-HOME ®.

Product Record IMPORTANT: Fill out the product record information below.

Model Number

Serial Number

See rating label on grill for serial number.

Date Purchased

CAUT,ON

For residential use only. Do not use for commercial cooking.

NOTE TO INSTALLER: Leave this User's Manual with the

customer after delivery and/or installation.

NOTE TO CONSUMER: Leave this User's Manual in a

convenient place for future reference.

Safety Symbols

The symbols and boxes shown below explain what each heading means. Read and follow all of the messages found throughout

the manual.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicatesan potentially hazardous situation which,if notavoided, could resultin death or seriousinjury.

CAUTION: Indicates a potentially hazardoussituationor unsafepractice which, if notavoided, may resultin minoror

moderate injury.

2 ° 29163-30800317

For Your Safety ...

Grill Service Center...

Product Record Information... Installation Safety Precautions...

Safety Symbols ...

Kenmore Grill Warranty...

Use and Care...

Parts List... Parts Diagram ..

Before Assembly...

Assembly... Troubleshooting...

.2 .2

•4

... 5-13

•..14

• .15

... 16-18

•. •19-38

•. •39-41

Repair Protection Agreements Congratulations on making a smart purchase. Your new Kenmore®

product is designed and manufactured for years of dependable operation. But like all products, it may require repair from time to time

That'swhen having a RepairProtection Agreement can save you money and aggravation.

Purc/Tasea Repair Protection Agreement now and protect yourself from unexpected i?assleand expense.

Here's what the RepairProtection Agreement_ includes:

Sears Installation Service For Searsprofessional installation of home appliances, garage

door openers, water heaters, and other major home items,in the U.S.A.call 1-800-4-MY-HOME ®

CALIFORNIA PROPOSITION 65

1. Combustion by-products produced when using this product contain chemicals known to the State of

California to cause cancer, birth defects, and other

reproductive harm.

2. This Product contains chemicals, including lead and lead compounds, known to the State of California

to cause cancer, birth defects or other reproductive

harm.

Wash your hands after using this product.

[] Expert service by our 10,000 professional repair specialists [] Unlimited service and no charge for parts and labor on all

covered repairs

[] Product replacement up to $1500 if your covered product

can't be fixed

[] Discount of 25% from regular price of service and related

installed parts not covered by the agreement; also,25% off regular price of preventive maintenance check

[] Fasthelp by phone- we call it RapidResolution-

phone support from a Searsrepresentative. Think of us asa "talking owner's manual."

Once you purchase the RepairProtection Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night,or schedule a service appointment online.

The RepairProtection Agreement isa risk-free purchase. If you cancel for any reason during the product warranty period, we will

provide a full refund.Or, a prorated refund anytime after the product warranty period expires. Purchaseyour Repair

Protection Agreement today! Some limitationsand exclusionsapply. Forprices and

additional information in the U.S.A.call 1-800-827-6655.

29163-30800317 ° 3

Kenmore Elite Limited Warranty When installed, operated and maintained according to all supplied instructions, free in-home warranty service is

provided from the date of purchase for the parts, time periods and conditions specified in the list below. Call

1-800-4-MY-HOME ® to arrange for warranty service.

Two years replacement and installation for all parts defective in material or workmanship

Five years replacement for a heat diffuser that rusts through or burns through Fifteen years replacement for a burner that rusts through or burns through

Twenty-five years part replacement if the firebox cast aluminum sidewalls, lid porcelain coated shroud, or any

cooking grate rusts through or burns through After the second year from the purchase date, you are responsible for the labor cost of part installation. All warranty coverage excludes ignitor batteries and grill part paint loss, discoloration or surface rusting, which are

either expendable parts that can wear out from normal use within the warranty period, or are conditions that can be the result of normal use, accident or improper maintenance.

All warranty coverage is void if this product is ever used for other than private household purposes.

This warranty applies only within the conditions stated above, and will NOT pay for:

1. Expendable items that can wear out from normal use within the warranty period, including but not limited to batteries, light bulbs and surface coatings or finishes.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions

supplied with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product resulting from natural catastrophe, such as flood, fire or storm.

7. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than

those recommended in all instructions supplied with the product.

8. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies

Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the

shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and

provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitation on the

duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears Brands Management Corporation, Hoffman Estates, IL60179

4 ° 29163-30800317

• NEVERstore a spare LPcylinder under or near the appliance or in an enclosed area.

v v

• Never fill a cylinder beyond 80% full.

• If the information in the two points above is not followed exactly, a fire causing death or serious

injury may occur.

• An overfilled or improperly stored cylinder is a

hazard due to possible gas release from the safety

relief valve. This could cause an intense fire with risk of property damage, serious injury or death.

• If you see, smell or hear gas escaping, immediately get away from the LP cylinder and appliance and call your fire department.

LP Tank Removal, Transport And Storage

• TurnOFFall control knobs and LPtankvalve. Turn coupling nut

counterclockwise by hand only - do not use tools to

disconnect. Lift LPtankwire upward off of LPtank collar, then lift

LPtank up and off of support bracket. Installsafety cap onto LP

tank valve. Always use cap and strap supplied with valve.

Failure to use safety cap as directed may result in serious

personal injury and/or property damage.

LPTank Valve, _

\,\ Safety Cap

__ RetainerStrap

• A disconnected LPtank in storage or being transported must havea safety cap installed (as shown). Do not store an LPtank

in enclosed spaces suchasa carport, garage, porch, covered

patio or other building. Never leave an LPtank inside a vehicle

which may become overheated by the sun.

° Do not store an LPtank in an area where children play.

LP Cylinder

• The LPcylinder used with your grill must meet the following requirements:

• Use LPcylinders only with these required measurements:12" (30.5cm) (diameter) x 18"(45.7 cm) (tall) with 20 lb. (9 kg.)

Capacity maximum.

• LPcylinders mustbe constructed and marked in accordance

with specifications for LPcylinders of the U.S.Department of Transportation (DOT) or for Canada, CAN/CSA-B339,

cylinders, spheres and tubes for transportation of dangerous goods. Transport Canada (TC). See LPcylinder collar for marking.

• LPcylinder valve musthave: ° Type I outlet compatible with

regulator or grill.

• Safety relief valve.

• UL listed Overfill Protection

Device (OPD). ThisOPDsafety OPDHandWheel feature isidentified by a unique triangular hand wheel. Use

only LPcylinders equipped with this type of valve.

• LPcylinder must be arranged for vapor withdrawal and

include collar to protect LPcylinder valve. Always keep LP cylinders in upright position during use,transit or storage.

LPcylinder inupright position for vapor withdrawal

LP (Liquefied Petroleum Gas)

• LPgas is nontoxic, odorless and colorless when produced. For Your Safety, LPgas hasbeen given an odor (similar to rotten cabbage) so that it can be smelled.

• LPgas is highly flammable and may ignite unexpectedly when mixed with air.

LP Cylinder Filling

• Useonly licensed andexperienced dealers.

• LPdealer mustpurge new cylinder before filling.

• Dealer should NEVERfill LPcylinder more than 80% of LP cylinder volume. Volume of propane in cylinder will vary by

temperature.

• A frosty regulator indicates gas overfill. Immediately close LP cylinder valve and call local LPgas dealer for assistance.

• Do not release liquid propane (LP)gas into the atmosphere. This isa hazardous practice.

• To remove gas from LPcylinder, contact an LPdealer or call a local fire department for assistance.Check the telephone directory under "Gas Companies" for nearest certified LP

dealers.

29163-30800317 "5

LP Tank Exchange Connecting Regulator To The LP Tank

• Many retailers that sellgrills offer you the option of replacing your empty LPtank through an exchange service Use only those

reputable exchange companies that inspect, precision fill, test and certify their cylinders Exchange your tank only for an OPD safety feature-equipped tankas described inthe "LPTank"

sectionof thismanual

• Always keep new and exchanged LPtanksin upright position during use,transit or storage

• Leaktest new and exchanged LPtanksBEFOREconnecting to grill

LP Tank Leak Test

For your safety

• Leaktest must be repeated each time LPtank is exchanged or refilled

• Do not smokeduring leak test

• Do not usean open flame to check for gas leaks

• Grill mustbe leak tested outdoors in a wellventilated area, away from ignition sources suchasgas fired or electrical appliances During leak test, keep grill away from open flames

or sparks

• Usea clean paintbrush and a 50/50 mild soap and water solution Brushsoapy solution onto areas indicated by arrows

infigure below Leaksare indicated by growing bubbles

1 LPtank must be properly secured onto grill (Referto

assembly section.) 2 Turnall control knobs to the OFFposition 3 TurnLPtankOFFby turning OPD hand wheel clockwise to a

full stop 4 Removethe protective cap from LPtank valve Always use

cap and strap supplied with valve

_PDHand Wheel

_e1outlet with

thread on outside

Safety Relief

Strap and Cap

• Do not usehousehold cleaning agents Damage to the gas train components (valve/hose/regulator) can result

Do not insert a POL transport plug

(plastic part with external threads) into the type 1 valve outlet. It will defeat the Safety

Relief Valve feature.

5 Hold regulator and insert nipple into LP

tank valve Hand tighten the coupling nut,holding regulator in a straight line

with LPtank valve so as not to crossth thread the connection

Nipple has to be

centered into the LP

tank va Ilii\_'_.

6 ° 29163-30800317

Hold coupling nut and regulator as shown for proper connection

to LPtank valve.

Leak Testing Valves, Hose and Regulator

1.Turnall grill control knobsto OFF.

2Be sure regulator is tightly connected to LPtank

3Completely open LPtank valve by turning OPD hand wheel

counterclockwise If you hear a rushing sound, turn gas off immediately There is a major leak at the connection Correct

before proceeding by calling Sears for replacement parts at 1-800-4-MY-HOME ®

4Brush soapy solution onto areas where bubbles are shown in

picture below:

• Never remove threaded

6 Turn the coupling nutclockwise andtighten to a full stop The

regulator will seal onthe back-check feature in the LPtank

valve, resulting in someresistance An additional one-half to three-quarters turn isrequired to complete the connection.

Tighten by hand only - do not usetools.

NOTE:

Ifyou cannot complete the connection, disconnect regulator

and repeat steps5 and 6.If you are still unable to complete the connection, do not usethisregulator!

Call 1-800-4-MY-HOME ® for an identical replacement part.

• Do not insert any tool or foreign object into the valve outlet or safety relief valve You may damage the valve

and cause a leak Leaking propane may result in explosion, fire, severe personal injury, or death

• Outdoor gas appliance is not intendedto be installed inor on a boat

• Outdoor gas appliance is not intendedto be installed in oron an RV

• Never attempt to attach thisgrill to the self-contained LPgas systemof a camper trailer or motor home

• Do not usegrill until leak-tested

• If a leak isdetected at anytime, STOPand call thefire department

• If you cannot stop a gas leak,immediately close LPcylinder valve and call LPgassupplier or your fire

department !

orifice at:nd of valve.

5 If _'growing_'bubbles appear, there is a leak Close LPtank

valve immediately and retighten connections If leakscannot be

stopped do not try to repair Call for replacement parts at 1-800-4-MY-HOME®

6 Always close LPtank valve after performing leak test by

turning hand wheel clockwise

29163-30800317 ° 7

For Safe Use of Your Grill and to Avoid Serious Injury:

• Do not let children operate or play near grill.

• Keep grill area clear and free from materials that

burn.

• Do not block holes in sides or back of grill.

• Use grill only in well-ventilated space. NEVER use in enclosed space such as carport, garage, porch, covered patio, or under an overhead structure of any kind.

• Do not use charcoal or ceramic briquets in a gas grill.

• Use grill at least 3 ft. from any wall or surface. Maintain 10 ft. clearance to objects that can catch fire, or to sources of ignition such as pilot lights on water heaters, live electrical appliances, etc.

Safety Tips

• Before opening LPcylinder valve, check the coupling nutfor tightness.

• When grill is not in use,turn off all control knobs and LPcylinder valve.

• Never move grill while inoperation or still hot.

• Use long-handled barbecue utensilsand oven mittsto avoid burns and splatters.

• Maximum load for sideburner and side shelfis 10Ibs.

• The grease tray mustbe insertedinto grill and emptied after each use.Do not remove grease tray until grill hascompletely cooled.

• Clean grill often, preferably after each cookout. If a bristle brush is usedto clean any of the grill cooking surfaces,ensureno loose

bristlesremain on cooking surfaces prior to grilling. It is not recommended to clean cooking surfaces while grill is hot.

• If you notice grease or other hot material dripping from grill, determine the cause,correct it, then clean and inspectvalve. Keep ventilation openingsin cylinder enclosure (grill cart) free and clear

of debris.

• Do not store objects or materials insidethe grill cart enclosure that would block the flow of combustion air to the underside of either

the control panel or the firebox bowl.

• The regulator may make a hummingor whistling noiseduring operation. Thiswill not affect safety or useof grill.

• If you have a grill problem see the "Troubleshooting Section".

• If the regulator frosts, turn off grill and LPcylinder valve immediately. Thisindicates a problem with the cylinder and it shouldnot be used on any product. Returnto supplier!

• Apartment Dwellers: Check with management to learn the requirements

and fire codes for using an LPgas grill in your apartment complex. If allowed, use outside on the

ground floor with a three (3) foot clearance from walls or rails. Do not use on or under balconies.

• NEVER attempt to light burner with lid closed. A buildup of non-ignited gas inside a closed grill is

hazardous.

• Never operate grill with LPcylinder out of correct position specified in assembly instructions.

• Always close LPcylinder valve and remove coupling nut before moving LPcylinder from

specified operation position.

• Putting out grease fires by closing the lid is not possible. Grills are well ventilated for safety reasons.

• Do not use water on a grease fire. Personal injury may result. If a grease fire develops, turn knobs and LP

cylinder off.

• Do not leave grill unattended while preheating or burning off food residue on HI. If grill has not been regularly cleaned, a grease fire can occur that may damage the product.

Main Burner Igniter Lighting

• Do not lean over grill while lighting.

1.Open lid during lighting.

2.Turnonvalve from source or tank.

3.Pushand turn any Main Burnercontrol knob to _ Hi and hold in. Youwill hear a clicking sound from the

electrodes of all burners.

4. If ignition does not occur in 5seconds,turn the burner controls OFF,wait 5 minutes,and repeat the lighting

procedure.

5. To ignite any other Main Burner,turn knob to HI.

Ifigniter does not work, follow Match Lightinginstructions.

8 ° 29163-30800317

Turn controls and gas source or tank OFF when not in use.

CAUTION

If ignition does NOT occur in 5 seconds, turn the

burner controls OFF, wait 5 minutes and repeat the lighting procedure. If the burner does not ignite with

the valve open, gas will continue to flow out of the burner and could ignite with risk of injury.

Match Lighting

ADo notlean over grill while lighting.

1.Open lid during lighting.

2. Place match into match holder (hanging on back of left door). Lightmatch, place into lighting hole on left side of firebox.

3. Turn right knob to HI position. Besure burner lightsand stay lit.

4. Lightother burners follow with step 3.

Burner Flame Check

• Removecooking grates and heat diffusers. Light burners,turn

knobsfrom HI to LO. You should seea smaller flame in LO position than seenon HI. Perform burner flame check on sideburner, also. Always check flame prior to each use.If

only low flame isseenrefer to "Sudden flame drop or low flame" in

the Troubleshooting Section.

Turning Grill Off

• Turnall knobsto OFFposition. Turn LPcylinder off by turning Igniter Check

• Turngas off at LPcylinder. Pressand hold electronic igniter button."Clicking" should be heard and spark seen each time

between collector box or burner and electrode. See "Troubleshooting" if no click or spark.

Valve Check

• Important: Make sure gas is off at LPcylinder before checking valves. Knobs lock in OFFposition. To check

valves, first pushinknobsand release, knobs shouldspring

back. If knobs do not spring back, replace valve assembly before usinggrill. Turn knobsto LOW position thenturn back to OFFposition.Valves should turn smoothly.

Hose Check

• Before each use,check to see if hosesare cut or worn. Replacedamaged hosesbefore usinggrill. Useonly

valve/hose/regulator as specified in the parts list of this Use & Care

Guide.

General Grill Cleaning

• Do not mistake brown or black accumulation of grease and smokefor paint. Interiorsof gas grills are not painted at the

factory (and should never be painted). Apply a strong solution of detergent andwater or usea grill cleaner with scrub brush

on insidesof grill lid and bottom. Rinseand allow to completely air dry. Do not apply a caustic grill/oven cleaner to painted

surfaces.

• Porcelain surfaces: Because of glass-like composition, most residue can be wiped away with baking soda/water solution or specially formulated cleaner Usenonabrasive scouring powder

for stubborn stains

• Paintedsurfaces: Wash with mild detergent or nonabrasive cleaner and warm soapy water Wipe dry with a soft n.onabrasivecloth

• Stainlesssteel surfaces: To maintain your grill's high quality appearance, wash with mild detergent and warm soapy water

andwipe dry with a soft cloth after each use Baked-on grease deposits may require the useof an abrasive plastic cleaning pad Use only in direction of brushed finishto avoid damage Do notuseabrasive pad on areas with graphics

• Cooking surfaces: If a bristle brushisusedto clean any of

the grill cooking surfaces,ensureno loose bristles remainon

cooking surfaces prior to grilling It isnot recommended to clean cooking surfaceswhile grill ishot

29163-30800317 ° 9

CAUTION

SPIDER ALERT!

IMPORTANT: Always ensure that the venturi burner tubes are clean. A venturi burner tube hasa narrow area in

which spiders tend to build nests.

Ifyou notice that your grill isgetting hard to light or that the flame isn't as strong as it should be, take the time to check and

clean the venturi's.

- !

Spiders or small insects have been known to create "flashback" problems. The spiders spin webs, build nestsand lay eggs in the grill's

venturi tube (s) obstructing the flow of gas to the burner. The backed-up gas can ignite in the venturi behind the control panel. This isknown as a flashback and it can damage your grill and even cause injury.

Cleaning the Burner Assembly

Follow these instructionsto clean and/or replace parts of burner

assembly or if you have trouble igniting grill 1 Turngas off at control knobs and LPcylinder

2 Remove cooking grates and heat diffusers 3 Remove cotter pinfrom rear of burners

4 Carefully lift each burner up and away from valve openings We _uggestthree ways to clean the burner tubes Usetheone

easiestfor you

(A) Benda stiff wire (a light weight coat hanger works well)

into a small hook Runthe hook through each burner

tube several times

Z2Z Z]L] Z2 .....

(B) Usea narrow bottle brushwith a flexible handle (do not use

a brasswire brush), runthe brushthrough each burner tube several times

the burner tube and out the burner ports Check each port to make sure air comes out each hole

5 Wire brushentire outer surface of burner to remove

food residue and dirt

6 Clean any blocked ports with a stiff wire such as an

open paper clip

7 Check burner for damage, due to normal wear and

corrosion some holes may become enlarged If any large cracks or holesare found replace burner

VERYIMPORTANT: Burnertubes mustreengage valve openings.See illustrations below.

Topreventflashbacksandensuregood performancethe burnerand venturiassemblyshouldbe removedfromthegrillandcleaned

'beforeusewheneverthegrill hasbeenidleforanextendedperiod.

Storing Your Grill

•Clean cooking grates

•Store in dry location

•When LPcylinder isconnected to grill, store outdoors in a

wellventilated space and out of reach of children

•Cover grill if stored outdoors Choose from a variety of grill covers offered by manufacturer once available

•Store grill indoors ONLY if LPcylinder isturned off and Disconnected, remove from grill and stored outdoors

• When removing grill from storage, follow "Cleaning the Burner

Assembly' instructions before starting grill

10 ° 29163-30800317

8 Carefully replace burners 9 Attach burners to brackets with cotter pin

10 Replace heat diffusers and cooking grates

Indirect Cooking

Poultry and large cuts of meat cook slowly to perfection onthe grill by indirect heat. Place food over unlit burner(s);the heatfrom lit burners circulates gently throughout the grill, cooking meat or poultry without the touch of a direct flame. This method greatly reduces flare-ups when cooking extra fatty cuts because there isno direct flame to ignite the fats and juices that drip during cooking.

1 Burner Cooking

Cook with direct or indirect heat.

Bestfor smaller mealsor foods.

Consumeslessfuek

Indirect Cooking Instructions

• Always cook with the lid closed.

° Dueto weather conditions, cooking times may vary. During

cold and windy conditions the temperature setting may

need to be increased to insuresufficient cooking

temperature.

° Place food over over unlit burner(s).

Food Safety

Food safety isa very important part of enjoying the outdoor cooking experience. To keep food safe from harmfulbacteria,

follow thesefour basic steps: Clean: Wash hands,utensils,and surfaces with hot soapy water

before and after handling raw meat and poultry. Separate: Separate raw meats and poultry from ready-to-eat foods to avoid cross contamination. Usea clean platter and utensilswhen removing cooked foods. Cook: Cook meat and poultry thoroughly to kill bacteria. Use a thermometer to ensure proper internal food temperatures. Chill: Refrigerate prepared foods and leftovers promptly. For more information call: USDA Meat and Poultry Hotline at 1-800-535-4555 (InWashington, DC (202) 720-3333, 10:00 am

4:00 pm EST).

How To Tell If Meat Is Grilled Thoroughly

• Meat and poultry cooked on a grill often browns very fast

on the outside. Use a meat thermometer to be surefood has reached a safe internal temperature, and cut into food to check for visual signsof doneness.

° Whole poultry should reach 180° F; breasts, 170° F.Juices

should run clear and fleshshould not be pink.

° Hamburgers made of any ground meat or poultry should

reach 160° F,and be brown in the middle with no pink juices Beef, veal and lamb steaks, roasts and chops can be cooked to 145° F.All cuts of pork should reach 160° F.

° NEVERpartially grill meat or poultry and finishcooking

later. Cook food completely to destroy harmful bacteria.

° When reheating takeout foods or fully cooked meats like

hot dogs, grill to 165° F,or until steaminghot.

2 Burner Cooking

Great indirect cooking on low. ProducessJow,even heating. Ideal for slow roastingand baking.

WARNING: To ensurethat it is safe to eat,food mustbe cooked to the minimuminternal temperatures listed in the table below.

USDA* Recommended Safe Minimum Internal Temperatures Beef,Veal, Lamband Pork Whole Cuts_ 145° F

Fish 145° F Beef,Veal, Lamband Pork Ground 160° F Egg Dishes 160° F Turkey, Chicken & Duck Whole, Pieces & 165°F

Ground

United States Department of Agriculture

_AIIow meat to rest three minutesbefore carving or consuming.

29163-30800317 ° 11

To purchase Natural Gas Conversion Partscall Searsat

1-800-4-MY-HOME ®

Natural Gas Conversion Kit

Service Part 30800331

Or In-store part 30611

item: 590-06109657-4

Your grill can be converted to natural gas with this

conversion kit by a qualified gas technician only. To convert this grill the technician will need this conversion kit.

iiiiiii

Naturalgas 12'hose

If converting the grill to natural gas, the technician in mostcases will need this 12'extension hose with 3/8" ID

(innerdiameter), which is included in the natural gas

conversion kit.

12 ° 23674-30800316

For Natural Gas Connection Preparing:

1. Turnoff gas supply,and thenremove cap on gas Supply side.

2. Recommended: Installa shut-off valve on gas supply side before installingthe socket.

3. Socket should be installed by an authorized technician in accordance with the national fuel gas

code (NFPA54/ANSI223.1)

4. Before inserting plug,turn on gas supply and leak test all connections including the stemof the shut-off

valve and the opening of the socket. Forbest results, useand ammonia-free soap & water solution.

Gas Requirements

LPGas

If your grill isfor [P Gas, the regulator supplied isset for

an 11-in.Water column (WC} and is for use with I.Pgas only. The factory-supplied regulator and hose must be

usedwith a 20-lb. I.Pgas tank.

Natural Gas

If your grill isfor Natural Gas, it is set for a 7-in. water

column (WC} and is for usewith Natural Gas only. Gas

pressure is affected by gas line size and the length of

gas line run from house gas line. Follow the

recommendations inthe chart below.

From House to Grill

Distance Tubing Size

Operating Instructions:

1.To connect, pushback socket sleeve.

Socket Sleeve _ Plug

2. Insertplug and release sleeve.

3. Pushplug untilsleeve snapsforward. (Gas will flow

automatically. Failure to connect plug properly to socket will inhibitgas flow to the appliance.}

Socket S_eeve

Up to 25 ft. 3//8 in. diameter

26-50 ft. i/2 in. diameter

51-100 ft. 2/3 of the run: 3/4 in. diameter

1//3 of the run: 1/2 in. diameter

Over 101ft. 3//,4 in. diameter

To disconnect

1. PullSleeve back. Pullplug out socket. (Gas is automatically shutoff.}

2. Close shut-off valve and replace dust caps on socket and plug.

29163-30800317 ° 13

Key

End Cap, Right Side Shelf 1

Right Side Shelf 1

Fascia, Right Side Shelf 1

Control Panel 1

Pulse Control Line 1

Pulse Ground Wire 1

Gas Valve, Main Burner 3

Manifold 1

Gas Hose 1

Regulator Retention Bracket 1

Connector B 1

Regulator 1

Regulator Hose Hanger Clip 1

Control Knob Bezel 3

Control Knob 3

Bottom Shelf 1

Magnet Box 1

Magnet 4

Caster 2

Caster with Brake 2

Tank Positioning Pin 2

Cart Support Angel Bar 2

Right Door Pin Support 1

Left Door Pin Support 1

Right Side Panel 1

Grease Box 1

Grease Box Bracket Support 1

Grease Box Bracket 1

Door Handle 2

Match Holder 1

Match Holder Bracket 1

32-1

Right Door (Metallic Black) 1

32-2

Right Door (Vermillion Red} 1

32-3

Right Door (Champaign) 1

33-1

Left Door (Metallic Black) 1

Description Qty

Pad Number

30800206

30800041

30800044

30800024

30800224

30800225

30800212

30800028

30800217

30800054 30800218

40800115

30800226

40900036

30800219

30800074

40200072

40200094

40900213

40900212

30800229

40900060

30800058

30800057

30800051

30800082

30800081

30800080

30800068

40800128

40800129

30800066B

30800066C

30800066D

30800060B

Key Description Qty

33-2 Left Door (Vermillion Red} 1

33-3 Left Door (Champaign} 1 34 Left Side Panel 1

35 Back Panel 1

36 Hex Nut 1

37 Electronic Ignition Module 1 38 Main Burner Electrode L850 1

39 Main Burner Electrode L650 1

40 Main Burner Electrode L450 1

41 Grease Panel 1 42 Main Burner 3

43 Fascia, Left Side Shelf 1

44 End Cap, Left Side Shelf 1 45 Left Side Shelf 1

46 Lid Handle 1

47 Rubber Bumper, Lid 2

48 Rubber Bumper, Lid 2

49 Temperature Gauge 1

50 Temp Gauge Bezel 1

51 Logo 1

52 Rotate Rod, Lid 2

53 Lid Handle Spacers 2

54 Bezel, Lid Handle 2 55 Cotter Pin 5

56-1 Lid ( (Metallic Black) 1

56-2 Lid (Vermillion Red) 1

56-3 Lid (Champaign) 1

57 Warming Rack 1

58 Cooking Grid 2 59 Heat Diffuser 3

60 Firebox 1

61 Door Bracket 1

62 Fuel Gauge 1 63 Badge 1

Pad Number

30800060C

30800060D

30800049

30800053

30800218

30800223

30800220

30800221

30800222

30800019 30800086

30800036

30800205

30800031

30800010

40700103

40800107

30800207

30800208

30800209

40800108

30800231

30800011

110024

30800002B

30800002C

30800002D

30800210

30800211

30800018

30800013

30800056

30800087 30800232

Not Pictured

Hardware Pack 1

Manual 1

Natural Gas Conversion Kit, Purchase Separately 1 See Pages 12 & 13

14 " 29163 -30800317

30800330

30800317 30800331

If you are missinghardware or have damaged parts after unpacking grill,

call 1-888-287-0735 for replacement.

To order replacement parts after usinggrill, call 1-800-4-MY-HOME ®

i_iiiii;i;i

I\ /

................... A_

..... . -or - . _i_J-

__7__.______====_ ¸--_

'mYi.....................................]D

......... _ .......................................... j

f ...............

29163 -30800317 • 15

READ AND FOLLOW THE INSTRUCTIONS BELOW TO CORRECTLY UNPACK GRILL PARTSFROM

SHiPPiNG BOX.

Step 1: Use a box cutter knife to slice down the sides of the carton box. Be careful of staples along the edges. Remove all parts, part boxes, and packing material from the top, sides and

bottom of cjrill head.

16 " 29163-30800317

Step 2: Tilt grill head up to one side and then to other side to remove large Styrofoam side pieces. Also, remove packing material from regulator hose and igniter wires. Be sure to remove grease tray from left

Styrofoam side piece.

_ _ _'_ ¸¸,¸3_ ,,_ ¸¸¸¸,¸¸¸¸2,,i_ _ ,,_

29163-30800317" 17

Step 3: With grill head resting on base on shipping box cardboard, raise grill head lid, and remove all

part boxes and packing material from inside the grill head. Allow grill head to rest on cardboard until placing grill head on cart during assembly.

18 * 29163-30800317

CAREFULLY READ AND PERFORMALL ASSEMBLY iNSTRUCTiONS ON THE FOLLOWING PAGES.

Tools Required:

• Adjustable wrench (not provided)

• 7/16" Combination wrench (not provided)

• The following hardware is provided in blister pack for convenient use.

M4X10 Screws

Qty: 42 pcs

M5X10 Screws

Qty: 4 pcs

M6X13 Screws (Black)

Qty: 26 pcs

M4X12 Screws

Qty: 2 pcs

M5 flat washer

Qty: 4 pcs

M6X13 Screws (gray)

Qty: 12 pcs

AA Battery Qty: 1 pc

M6X20 Screws

Qty: 4 pcs

M6 flat washer

Qty: 4 pcs

Tank Positioning Pin

Qty: 2 pcs

29163-30800317 " 19

Casters to Cart Base [] Turncart base upside down. Attach the casters to cart base with (16)M6 X 13black screws.

Casters with brakes attach to rear of cart base.

M6X13 screws (Black) Qty: 16 pcs

Swivel Casters

Swivel Caster with Brake

Panel Front

Panel Rear

20 " 29163-30800317

M4XIO SCrews Qty: 2 pcs

\\\

lUrn cart base fight side up. Attach door

magnets to cart base with C2)M4xlO Screws.

Side Panels

[] To attach side panel, align holes in panel bottom with holes in cart base. [] Attach left and right side panelsto cart base with (6) MBx13gray screws.

[] NOTE: The right panel hasfour fuel gauge attachment holes.

M6X13screws (Gray) Qty: 6 pcs

// i

FuelGaug4Attachment Holes

22 ° 29163-30800317

[] Attach back panel to cart base and two side panels with (8) M4xl0 screws. Back Panel

M4XIO screws Qty: 8 pcs

29163-30800317 ° 23

FuelGauge [] Attach fuel gauge to right side panel with (4) M6x13 gray screws from outside to inside of

cart

[] Attach (2) tank positioning pinsto right side panel with (2) M6x13 gray screws.

M6X13 screws (Gray) Qty:6 pcs

Tank positioning pins Qty: 2 pcs

24 ° 29163-30800317

Positioning Pins

Grease Cup Bracket

[] Attach grease cup bracket to grease cup bracket support with (2) M4xl0 screws. [] Attach grease cup bracket to left side panel with (2) M4xl0 screws from outside to insideof cart.

Attach grease cup bracket support to cart basewith (2) M4xl0 screws

M4XIO screws

Qty: 6 pcs

29163-30800317 ° 25

+ 57 hidden pages