Kemppi R11T User Manual

– R11T/0236

2.

4

4.

TECHNICAL DATA

R11T/0236 – 3

products should prove to be productive machines requiring maintenance at only

regular intervals. This manual is arranged to give you a good understanding of

the equipment and its safe operation. It also contains maintenance information

without prior notice.

In this document, for danger to life or injury the following symbol is used:

Read the warning texts carefully and follow the instructions. Please also study

the Operation safety instructions and respect them when installing, operating and

R11T is transmitter part for remote control unit which is designed for MMA

welding with Master MLS power sources. Master MLS power sources have an

R11T is using welding cables for transfer of control information, longest

You can use wireless remote control unit with following power sources from

Master 1600 MLS (6102160): all serial numbers

Master 2500 MLS (6104250): from number 1071536

Master 3500 MLS (6104350): from number1066406

Mastertig 2000 MLS (6112200): all serial numbers

Mastertig 2500 MLS (6114250): from number 1064082

Mastertig 3500 MLS (6114350): from number 1066756

manufactured before these.

– R11T/0236

X2

Be careful for voltage! Between work piece

Do not try to use remote control device with other power sources than

with those mentioned above! See to that cables you intend to use are

Be careful for not touching enclosure of remote control device with hot electrode!

Do not put control device onto hot work piece!

Do not throw or drop remote control device!

Power source

into remote control

position

Use of a remote control unit with cables is not possible at the same time with

R11T. Disconnect remote control unit with cables from power source’s connector.

R11T control transmitter

control electrode

potentiometer

earthing electrode

signal lamp

R11T/0236 – 5

Adjust potentiometer R1 to required value according

to reference scale.

2.

Place R11T between work piece and welding

Red lamp H1 of R11T turns on, telling that control

When the lamp is on, you can also adjust current

transmitted as set value of power source.

4.

Remove R11T and start welding.

If red lamp of R11T is not on, there is no control connection and set value is not

transmitted onto the power source.

R11T is protected against disturbances caused by TIG ignition sparks.

NOTE! Master MLS power sources remember the last adjusted value after switching

In case of problems contact the KEMPPI works in Lahti, Finland or your KEMPPI

In order to avoid operation disturbances:

Keep R11T clean. Do not open the control device!

Avoid operating R11T in rain or in corresponding moist circumstances.

R11T

R11T

Data transmission

Enclosure

plastic enclosure with suspension hook

External dimensions

width

height

weight

210 g

Degree of protection

KEMPPI OY
PL 13
FIN – 15801 LAHTI
FINLAND
Tel [phone]
Telefax [phone]
www.kemppi.com

KEMPPIKONEET OY
PL 13
FIN – 15801 LAHTI
FINLAND
Tel [phone]
Telefax [phone]
e-mail: myynti.fi @kemppi.com

KEMPPI SVERIGE AB
Box 717
S – 194 27 UPPLANDS VÄSBY
SVERIGE
Tel [phone]
Telefax (08) 59 082 394
e-mail: [e-mail]

KEMPPI NORGE A/S
PB 2151 Postterminalen
N – 3103 TØNSBERG
NORGE
Tel [phone]
Telefax 33 35 80 90
e-mail: [e-mail]

KEMPPI DANMARK A/S
Literbuen 11
DK – 2740 SKOVLUNDE
DANMARK
Tel [phone]
Telefax 44 941 536
e-mail:[e-mail]

KEMPPI BENELUX B.V.
Postbus 5603
NL – 4801 EA BREDA
NEDERLAND
Tel [phone]
Telefax [phone]
e-mail: [e-mail]

KEMPPI (U.K) Ltd.
4-6 Sergeants Way
Elms Industrial Estate
BEDFORD, MK 41 OEH
ENGLAND
Tel [phone]
Telefax [phone]
e-mail: [e-mail]

KEMPPI FRANCE S.A.
S.A. au capital de 5 000 000 F.
65 Avenue de la Couronne des Prés
78681 EPONE CEDEX
FRANCE
Tel [phone]
Telefax (01) 30 90 04 45
e-mail: [e-mail]

KEMPPI GmbH
Otto – Hahn – Straße 14
D – 35510 BUTZBACH
DEUTSCHLAND
Tel [phone]
Telefax (06033) 72 528
e-mail:[e-mail]

KEMPPI SP. z o.o.
Ul. Piłsudskiego 2
05-091 ZA¸BKI
Poland
Tel [phone]
Telefax [phone]
e-mail: [e-mail]

KEMPPI SWITZERLAND AG
Chemin de la Colice 4
CH-1023 Crissier/ Lausanne
SUISSE
Tel. [phone]
Telefax [phone]
e-mail: [e-mail]

KEMPPI WELDING
MACHINES AUSTRALIA PTY LTD
P.O. Box 404 (2/58 Lancaster Street)
Ingleburn NSW 2565, Australia
Tel. [phone]
Telefax [phone]
e-mail: [e-mail]

Ver. 4

www.kemppi.com