Kawasaki KLX140L 2014 Owner's manual

Quick Reference Guide
GENERAL INFORMATION j
This Quick Reference Guide will assist you in
finding the in
A Table of Contents is included after the
Foreword.
MAINTENANCE AND ADJUSTMENT j
TROUBLESHOOTING GUIDE j
STORAGE j
IMPORTANT INFORMATION
This vehicle is designed for the operator only, no passengers.
This vehicle is an off-road motorcycle only and was not manufactured for use on public streets, roads or
highways. Respect the environment and the rights of other people.
Read owner’s manual.
Whenever you see the symbols shown below, heed their instructions! Always follow safe operat­ing and maintenance
practices.
DANGER
DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
WARNING
WARNING indicates a hazardous situation
which, if not avoided, could result in de ath
or serious injury.
NOTICE
NOTICE is used to
latedtopersonalinjury.
NOTE indicates information that may help or guide
youintheopera
address practices not re-
NOTE
tion or service of the vehicle.
IMPORTANT
Off-road motorcycling is a wonderful sport, and we hope you will en ever, if improperly conducted, this sport has the potential to cause environmental problems as well as conflicts wi Responsible use of your off-road motorcycle will ensure that these problems and conflicts do not occur. TO PROTE SPORT, MAKE SURE YOU USE YOUR MOTOR­CYCLE LEGALLY, SHOW CONCERN FOR THE ENVIRONMENT, AND OF OTHER PE OPLE.
joy it to the fullest. How-
th other people.
CT THE FUTURE OF YOUR
RESPECT THE RIGHTS
WARNING
THIS VEHIC LE IS AN OFF-ROAD VEHICLE
ONLY AND WAS NOT MANUFACTURED FOR USE ON PUBLIC STREETS, ROADS, OR HIGH-WAYS. USEYOURBIKELEGALLY.
RESPECT THE ENVIRONMENT AND THE
RIGHTS OF OTHER PEOPLE.
IMPORTANT NOTE TO PAR
Your youngster’s saf a properly maintained vehicle. As w ith any moving vehicle there are possible safety risks; be sure to heed these precautions.
1. Always equip your child with suitable protective gear and riding apparel. Be sure he or she always wears a helmet, over-the-ankle footwear or sturdy boots, eye protection, groves, long pants, and a long-sleeved shirt while riding.
2.
Never allow your child to carry a passenger. This motorcycle is designed for an OPERATOR ONLY.
3.
This motorcycle is designed for off-road riding and should never be operated on public roads or paved surfaces.
4.
This motorcycle was not designed for hard riding such as motocross.
5.
Always obey local off-road riding laws and regulations. Obtain permission to ride on private property.
6.
You , the parent (and most likely “riding instructor/mechanic” as well), must be familiar with motorcycle controls and maintenance requirements plus riding techniques. Read and understand the owner’s manual provided with the motorcycle. Review all instructions and warnings with your child.
7.
You must determine your child’s readiness to ride this off-road motorcycle. Your child should already be familiar with motorcycle controls (location and function) and basic riding technique s. Your child should also be physically large enough, and strong enough to be able to straddle the motorcycle and hold it up, plus be able to pick up it up if it is on its side.
8.
Your child’s safety depends in part on the good mechanical condition of the motorcycle. Be sure to follow the maintenance and adjustment requirements contained in the Periodic Maintenance Chart, Daily Pre-ride Inspection, and After-Race Check Points. Be sure your child understands the importance of chec kin g all items thoroughly before riding the motorcycle. Also, familiarity with the motorcycle is important should a problem occur far from help.
9.
Do not allow your child to ride unsupervised. He or she should always ride in the company of an experienced adult.
ety will depend on your commitment to always provide a safe riding environment and
ENTS ABOUT SAFE RIDING
10.
Encourage your child them practice advanced riding maneuvers under controlled conditions.
11. Tell someone where you and your child are planning to ride and when you Intend to return. Discuss the ride with your ch may b e necessary to negotiate the terrain safely. If you are n ot familiar with the area, lead the way and reduce your speed.
KLX140A only
not to ride beyond his or her skill lever or faster than conditions safely allow. Have
ild before you leave so he or she will know in advance what riding techniques
NOTICE
KLX140A is designed for a rider weighting less than 70 kg (154 pounds). Exceeding this limit could damage the motorcycle.
WARNING
Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemi­cals known to the State of California to cause cancer and birth defects or other reproductive harm.
FOREWORD
We wish to thank you for choosing this Kawasaki Motorcycle. It is the end product of Kawasaki’s advanced engineering, exhaustive testing, and continuous striving for super ior reliability, and performance. By giving your motorcycle the proper care and maintenance outlined in this manual, you will be helping to ensure it a long, trouble-free life.
Before starting to ride your motorcycle, please read this manual thoroughly in order to know your motorcycle’s capabilities, its lim itations, and above all, how to operate it safety.
Due to improvements in design and performance m ade during production, in some cases there may be minor discrepancies between the actual vehicle and the illustrations and text in this manual.
KAWASAKI HEAVY INDUSTRIES, LTD.
Motorcycle & Engine Company
©2014 Kawasaki Hea
vy Industries, Ltd.
Feb. 22, 2014. (1)
TABLE OF CONTENTS
SPECIFICATIONS.................. .......................... 9
GENERAL INFORMATION.............................. 12
Location of Labels ......................................... 12
Location of Parts ........................................... 17
Side Stand ..................................................... 20
Fuel Tap......................................................... 20
Fuel ............................................................... 21
Engine Stop Switch ....................................... 24
Starter Button ................................................ 25
Starting the Engine
Moving Off ..................................................... 28
Shifting Gears................................................ 28
Stopping the Motor
Stopping the Engine ............... ....................... 30
Break-In........................................... .............. 30
Daily Pre-Ride Ch
MAINTENANCE AND ADJUSTMENT............. 33
EMISSION CONTROL INFORMATION ........ 33
Periodic Mainte
Engine Oil ...................................................... 40
Spark Plug ..................................................... 44
Air Cleaner ......................................... ........... 46
Throttle Cable ................................................ 51
Choke Knob................................................... 53
Idle Speed ........................... .......................... 55
Clutch ............................................................ 56
........................................
cycle................................
ecks ..................................
nance Chart ..........................
25
29
31
36
Valve Clearan ce ............................................ 57
Spark Arrester ................... ............................ 58
Drive Chain.................. .................................. 60
Handlebar ........ .................................... .......... 65
Brakes .............................................. ............. 67
Steering ................. .................................... .... 71
Front Suspension .......................................... 73
Rear Suspension .................. ......................... 74
Wheels ............... .................................... ....... 77
Hoses Inspect ion ........................................... 80
Battery ................... .................................... .... 81
Fuse .............................................................. 85
Tightening Torque
Cleaning Your Motorcycle..... ......................... 91
Lubrication ....... .................................... .......... 94
TROUBLESHOOTING
STORAGE................... .................................... . 99
Before Storage .............................................. 99
After Storage ................................................. 100
ENVIRONMENTAL PROTECTION .................. 101
WIRING DIAGRAM .......................................... 102
YOUR WARRANTY/
..................................................................... . 103
REPORTING SAFETY DEFECTS ................... 107
MAINTENANCE R
s of Nuts and Bolts............
GUIDE.........................
OWNER SATISFACTION
ECORD ..............................
86
97
108
SPECIFICATIONS 9

SPECIFICATIONS

DIMENSIONS
Overall length 1 820 mm (71.7 in.) B: 1 895 mm (74.6 in.)
Overall width 790 mm (31.1 in.)
Overall height 1 050 mm (41.3 in.) B: 1 075 mm (42.3 in.)
Wheelbase
Road clearance
Curb Mass 93 kg (205 lb) B: 95 kg (209 lb)
Fuel t an k capacity
ENGINE
Type
Bore × stroke
Displacement
Compression ratio
Carburetor
Starting system Electric Starter
Ignition system
Ignition timing
Lubrication system
Spark plug NGK CR7HSA
Spark plug terminal Screw type
1 260 mm (49.6 in.) B: 1 285 mm (50.6 in.)
235 mm (9.3 in.) B: 255 mm (10.0 in.)
5.8 L (1.5 US gal)
SOHC, 2-valve, single-cylinder, 4-stroke, Air-cooled
58.0 × 54.4 mm (2.3 × 2.1 in.)
144 cm³ (8. 8 cu in.)
9.5 : 1
KEIHIN PB20
CDI
10° BTDC @1 40 0 r/min (rpm) 30° BTDC @ 4 000 r/min (rpm)
Forced lubrication (wet sump)
10 SPECIFICATIONS
TRANSMISSION
Transmission type
Clutch type
Drive system
Gear ratios:
1st gear
2nd gear
3rd gear
4th gear
5th gear
Primary reduction ratio
Final reduction ratio
Overall ratio (top gear)
Engine oil:
Capacity 1.1 L (1.2 US qt)
Type
Viscosity
FRAME
Type Tubular, semi-double cradle
Steering angle 41° to either side
Caster 27°
Trail
5-speed, constan t mesh, return shift
Wet, multi disc
Chain drive
2.667 (40/15)
1.895 (36/19)
1.474 (28/19)
1.182 (26/22)
1.000 (24/24)
2.880 (72/25)
3.571 (50/14)
10.286
API SG, SH, SJ, SL o
SAE 10W-40
85 mm (3.3 in.) B: 96 mm (3.8 in.)
r SM with JASO MA, MA1 or MA2
Tire size, type:
Front
Rear
70/100-17 40M, IRC., B: 70/100-19 42M, IRC., LTD. IX05H
90/100-14 49M, IRC., LTD. IX05H B: 90/100-16 52M, IRC., LTD. IX05H
LTD. IX 05 H
Rim size:
Front 17 × 1.40 B: 19 × 1.40
Rear 14 × 1.60 B: 16 × 1.85
Suspension:
Front
Rear New Uni-trak
Front suspension travel
Rear wheel travel
Telescop ic fork
®
180 mm (7.1 in.)
180 mm (7.1 in.)
swinga
rm
Front fork oil:
Type
Amount (per fork leg
Kawasaki Fork Oil SS
)
296 mL (10.0 US oz) B: 290 mL (9.8 US oz)
-8
BRAKES
Type (Front & Rear)
ELECTRICAL EQUIPM
ENT
Disc
Battery 12 V 6 Ah
SPECIFICATIONS 11
B: KLX140B
Specifications are subject to change without notice.
12 GENERAL INFORMATION

GENERAL INFORMATION

Location of Labels

All warning labels which are on your vehicle are repeated here. Read lab derstand them thoroughly. They contain information which is important for your safety and the safety of anyone else who may ope fore, it is very important that all warning labels be on your vehicle in the locations shown. If any label is missing, damaged, or your Kawasaki de a ler and install it in the correct po­sition.
The sample warnin g labels in this section have
part numbers to help the correct replacement. Refer to the actual vehicle label for model spec ific
data grayed out in t
els on your vehicle and un-
rate your vehicle. There-
worn, get a replacement from
NOTE
you and your dealer obtain
he illustra tio n.
1. Brake Fluid (Front)
GENERAL INFORMATION 13
2. Brake Fluid (Rear)
3. Rear Shock Absorber Warning (KLX140A)
4. Important Information
5. Noise Emission Control Information
6. Vehicle Emission Control Information
j
14 GENERAL INFORMATION
7. Battery Poison/Danger
1)
3) KLX140A
GENERAL INFORMATION 15
j
2)
4)
16 GENERAL INFORMATION
5)
6)
7)

Location of Parts

GENERAL INFORMATION 17
j
1. Clutch Lever
2. Engine Stop Switch
3. Choke Knob
4. Front Brake Fluid Reservoir
5. Front Brake Lever
6. Throttle Grip
7. Starter Button
8. Fuel Tank Cap
18 GENERAL INFORMATION
9. Front For
10. Fuel Tank
11. Fue l Tap
12. Carbure
13. Seat
14. Air Cleaner Element
15. Brake D
k
tor
isc
16. Brake Cal
17. Engine Oil Drain Plug
18. Side Stand
19. Drive Ch
20. Swingarm
21. Chain Guide
22. Rear Sh
iper
ain
ock Absorber
GENERAL INFORMATION 19
j
23. Muffler
24. Fuse
25. Battery
26. Rear Axl
eNut
27. Chain Adj
28. Rear Brake Fluid Res ervo ir
29. Oil Filler Cap/Dipstick
30. Rear Bra
uster
ke Pedal
20 GENERAL INFORMATION

Side Stand

The motorcycle is equ
A. Side Stand
Do not sit on the motorcycle while it is on its side stand. Always kic on the motorcycle.
ipped with a side stand.
k the stand fully up before sitting
WARNING
Riding with the side stand down could cause
an accident resulting in serious injury or
death. Always be sure the side stand is fully
raised before riding.

Fuel Tap

The fuel tap has three (reserve). For normal operation, turn the fuel tap lever to the ON position. If the fuel runs out with the tap in t he ON position (0.29 US gal) of usable fuel remains can be used by turning the tap lever to the RES position.
A. Fuel Tap
B. ON Position
C. OFF Position
D. RES Position
Turn the fuel tap lever to OFF position when the fuel tank is removed for maintenance and adjust­ments or the mot
position: OFF, ON, and RES
, the last approximately 1.1 L
orcycle is stored for a long time.
NOTE
Since riding dista n ce is limited when on RES, re -
fuel at the earliest opportunity. Make certain that the fuel tap lever is turned to ON
(not RES), after fillin g up the fuel tank.
WARNING
Practice operating the fuel tap with the mo­torcycle stopped. To prevent an accident you should be able to operate the fuel tap while riding without taking your eyes off the road. Be careful not to touch the hot engine while operating the fuel tap.
GENERAL INFORMATION 21

Fuel

The required of fuel i
quirements”.
The capacity of the fuel tank is 5.8 L (1.5 US gal). To open the fuel tank c hose from the hole in the steering shaft and turn the tank cap counterclockwise.
Avoid filling the ta is blowing so that the fuel does not get contaminated.
s specified under “Fuel Re-
ap, disconnect the breather
nk in the rain or where heavy dust
j
A. Fuel Tank Cap
B. Breather Hose
22 GENERAL INFORMATION
Filling the Tank:
Avoid filling the tank in the rain or where heavy dust
is blowing so that the fuel does not get contaminated.
A. Tank Cap B. Fuel Tank C. Top Level D. Filler Neck
WARNING
Gasoline is extremely flammable and can be explosive under certain conditions, creating the potential for serious burns. Always stop the engine and do not smoke. Make sure the area is well-ventilated and free from any source of flame or sparks; this includes any appliance with a pilot light. Never fill the tank completely to the top. As the fuel expands in a warm tank, it may overflow through the vents in the tank cap. After refueling, make sure the fuel tank cap is closed securely. If gasoline is spilled on the fuel tank, wipe it off immediately.
Fuel R equirements:
Fuel Type
Use clean, fresh unleaded gasoline with a mini­mum Antiknock Index of 87. The Antiknock Index is posted on service station pumps in the U.S.A. The octane rating of a gasoline is a measure of its re­sistance to detonation or “knocking”. The Antiknock Index is an average of the Research Octane Num­ber (RON) and the Motor Octane Number (MON) as shown in the table below.
Octane Rating Method
Antiknock Index
RON + MON)
(
2
Minimum
Rating
87
NOTICE
If engine “knocking” or “pinging” occurs, use a different brand of gasoline of a higher octane rating. If th continue it can lead to severe engine dam­age. Gasoline quality is quality or not meeting standard industry specifications may result in unsatisfac­tory performance that result from the use of poor quality or non-recommended fuel may not be covered under your warran
Fuels Containing Oxygenates
Gasoline frequently contains oxygenates (alco­hols and ethers) especially in areas of the U.S. and Canada which are required to sell such reformu­lated fuels as part of a strategy to reduce exhaust emissions.
The types and volume of fuel oxygenates ap­proved for use in unleaded gasoline by the U.S. Environmental Protection Agency include a broad range of alcohols and ethers, but only two compo­nents have seen any significant level of commercial use.
is condition is allowed to
important. Fuels of low
. Operating problems
ty.
GENERAL INFORMATION 23
Gasoline/Alcohol Bl to 10% ethanol (alcohol produced from agricultural products such as corn), also known as “gasohol” is approved for use.
ends - Gasoline containing up
NOTICE
Avoid using blends of unleaded gasoline and
methanol (wood alcohol) whenever possible,
and never use “gasohol” containing more
than 5% methanol. Fuel system damage and
performance problems m ay result.
Gasoline/Ether Blends - The most common ether is methyl tertiary butyl ether (MTBE). You may use gasolinecontainingupto15%MTBE.
NOTE
Other oxygenates approved for use in unleaded
gasoline include TAME (up to 16.7%) and ETBE (up to 17.2%). Fuel containing these oxygenates canalsobeusedinyourKawasaki.
j
24 GENERAL INFORMATION
NOTICE
Never use gasoline with an octane rat­ing lower than the minimum specified by Kawasaki. Never use “gasohol” with more than 10% ethanol, or more than 5% methanol. Gaso­line containing met blended with cosolvents and corrosion inhibitors. Certain ingredien paint fading or damage. Be extra careful not to spill gasoline or gasoline oxygenate blends during ref When not operating your Kawasaki for 30 to 60 days, mix a fuel stabilizer (such as STA-BIL) with th Fuel stabilizer additives inhibit oxidation of the fuel which minimizes gummy deposits. Never store this thefuelsystem. Beforestorageitisrec­ommended that you drain all fuel from the fuel system. Se manual.
hanol must also be
ts of gasoline may cause
ueling.
e gasoline in the fuel tank.
product with “gasohol” in
e the Storage section in this

Engine Stop Switch

Theenginestopswitc
thehandlebar. Theenginestopswitchmustbeinthe
position for the moto
the switch to the
To avoid battery discharging, check that the en-
gine stop switch is in the dicator light (orange LED) goes off, when the mo­torcycle is not us
h is located on the left side of
rcycle to operate. Move
position to stop the engine.
NOTE
position and the in-
ed.
A. Engine Stop Switch B. Indicator L
ight (LED)
GENERAL INFORMATION 25
j

Starter Button

This motorcycle has t button operates the electric starter when the clu tch lever pulled in.
A. Starter Button
he starter button. The starter

Starting the Engine

Turn the fuel tap leve
A. ON Position
Shift the transm
This motorcycl
that prevents the engine from starting when the transmission is not in neutral.
r to the ON position.
ission in to neutral.
NOTE
e is equipped with a neutral switch
26 GENERAL INFORMATION
Check that the engine
position.
A. Engine Stop Switch
B.
Position
stop switch is in the
WARNING
Riding with the side stand in the down posi­tion can cause a crash resulting in injury. Do not start the engine or attempt to ride the mo­torcycle when the side stand is down.
NOTICE
Do not operate the starter continuously for more than 5 seconds, or the starter will overheat and the bat temporarily. Wait 15 seconds between each operation of the starter to let it recover.
When engine is cold:
Pull out the choke knob.
A. Choke Knob
Leaving the throttle completely closed, push the
starter butt
on until the engine starts.
tery power will drop
cool and the battery power
NOTE
When the clutch lever is pulled, the motorcycle can
be started with the transmission in any gear.
A. Starter Button
Even after the engine has started, do not push
back immediate is thoroughly warmed up.
When the engine is already warm or on a hot day,
open the throttle part way instead of using the choke knob.
ly the choke knob until the engine
NOTE
GENERAL INFORMATION 27
NOTICE
Do not let the engine idle longer than five minutes, or engine overheating and damage may occur.
j
28 GENERAL INFORMATION

Moving Off

Check that the side st
Shift into 1st gear.
Open the throttle slowly.
and is up.

Shifting Gears

This motorcycle is eq shift” transmission. The neutral is located halfway between 1st and 2nd gear. “Return shift” means that when shifting up engaged before the next higher or lower gear may be selected.
To engage first gea
in the clutch lever and push down on the shift pedal, gently release the clutch lever, then release the shift pedal. To shift up to the next gear, pull in the clutch lever,
lift the shift pedal with your toes, gently release the clutch lever, an To shift down to the next gear, pull in the clutch
lever, push the shift pedal down as far as it will go, gently release t shift pedal.
uipped with a 5-speed “return
or down, each gear must be
r from the neutral position, pull
d then release the shift pedal.
he clutch le ver, then release the
WARNING
Downshifting to a lower gear at high speed
causes engine rpm to increase excessively,
potentially damaging the engine and it may
also cause the rear wheel to skid and cause
an accident.
NOTICE
When changing gears, press firmly on the shift pedal to ensure proper shifting. Care­less, incomplete sh transmission to jump out of gear and lead to engine damage.
A. Shift Pedal
ifting can c ause the
GENERAL INFORMATION 29

Stopping the Motorcycle

For maximum decelera apply both front and rear brakes. Pull in the clutch lever as the motorcycle comes to a stop. Indepen­dent use of the front o geous in certain circu ms ta nc es . Shift down progres­sively to ensure good engine response at all speeds.
tion, close the throttle and
r rear brake may be advanta-
j
Loading...
+ 85 hidden pages