Jwin JL-725 User Manual

MODEL : JL-725

1. AUTO/ON/OFF SWITCH

2. LED CLOCK DISPLAY

3. LED INDICATOR FOR "AUTO"

4. SNOOZE/SLEEP-OFF BUTTON

5. ALARM SET/OFF BUTTON

6. TIME SET BUTTON

7. SLEEP SET BUTTON

8. (DIMMER) LOW/HIGH SWITCH

9. HOUR BUTTON

10. MINUTE BUTTON

11. VOLUME CONTROL KNOB

12. AM/FM SWITCH

13. TUNING CONTROL KNOB

14. BATTERY COMPARTMENT

15. FM PIG-TAILED WIRE

16. AC POWER CORD

17. AM/FM SCALE & POINTER

18. PROJECTION ON/OFF BUTTON

19. CLOCK PROJECTOR

20. TIME SET BUTTON FOR PROJECTION

21. HOUR BUTTON FOR PROJECTION

22. MINUTE BUTTON FOR PROJECTION

23. FOCUS ADJUSTMENT KNOB

24. RADIO/BUZZ SWITCH

25. LED INDICATOR FOR "PM"

AC POWER OPERATION

Before conneting to the power supply, ensure that the supply corresponds to the information on the rating label on the bottom of the apparatus.

WARNINGS

Disconnect the power plug from the receptacle when not in use. To avoid the risk of electric shock, do not remove the cover of the apparatus. There are no user serviceable parts inside. To prevent fire or shock hazard,

TO SET THE CLOCK TIME

1. Set the ON/OFF/AUTO switch (1) to 'OFF'. Connect the power cord to the power supply. The clock display will blink to indicate a power interruption and that the display time is incorrect.

2. To set the correct time, press the MINUTE button (10) or HOUR button (9) until the correct

time is displayed while pressing and holding the TIME SET button (6).

3. Open the Battery Compartment cover and fit a 9V battery. The purpose of this battery is to store the information relating to the alarm time and to keep the clock functioning in the event of disconnection from the power supply or power interrruption. In case of the power failure, the clock will

continue to keep time but will not display it.

TIME SETTING FOR PROJECTION

- To set HOUR, press simultaneously the HOUR BUTTON (21) and the TIME SET BUTTON (20).

Keep them depressed until the correct hour is displayed.

- To set MINUTE, press simultaneously the MINUTE BUTTON (22) and the TIME SET BUTTON (20). Keep them depressed until the correct minute is displayed.

- Focus setting : To adjust the projection focus, turn the FOCUS ADJUSTMENT KNOB (23) until

the projected time

do not expose the apparatus to rain or moisture.

THE LED DIGITAL CLOCK AND THE PROJECTION

CLOCK MUST BE SET SEPARATELY

is clearly shown on the ceiling or wall.

NOTE : THE MAXIMUM PROJECTION DISTANCE IS 3-9 FEET.

TO SET OR RESET THE ALARM TIME

1. Press and hold the ALARM SET/OFF button (5).

2. While holding the ALARM SET/OFF button (5), press the HOUR button (9) and MINUTE

button (10) to advance the time until the desired alarm time is shown on the display.

TO SET THE ALARM TO WAKE TO RADIO

1. Set the alarm time as previously instructed. Select a radio station and make sure the volume level is set as desired.

2. Slide the ON/OFF/AUTO switch (1) to the 'AUTO' position. Set the RADIO/BUZZ switch (24) to the

RADIO position. When the actual time matches the selected preset alarm time, the unit automatically

turns on for 1 hour and 59 minutes and then shuts off.

Notes :

- To shut off the alarm, press the ALARM SET/OFF button (5) once and alarm time will be reset for the next day. Slide the ON/OFF/AUTO switch (1) to the OFF position to turn off alarm and not set it for the next day.

- The alarm can be temporarily turned off manually by pressing the SNOOZE button (4). The radio

will turn on automatically 9 minutes later.

TO SET THE ALARM TO WAKE TO BUZZER

1. Set the alarm time as previously instructed. Set the RADIO/BUZZ switch (24) to the BUZZ position,

2. Slide the ON/OFF/AUTO switch (1) to the AUTO position. When the actual time matches the preset alarm time, the unit automatically turns on for 1 hour and 59 minutes and then shuts off.

Notes :

- To shut off the alarm, press the ALARM SET/OFF button (5) once and alarm time will be reset for t

he next day. Slide the ON/OFF/AUTO switch (1) to the OFF position to turn off alarm and not set

for the next day.

- The alarm can be temporarily turned off manually by pressing the SNOOZE button (4). The buzzer

will

turn on automatically 9 minutes later.

TO SET THE SLEEP TIME

1. Set the ON/OFF/AUTO switch (1) to 'OFF' or ‘AUTO’.

2. Press and hold the SLEEP SET button (7).

3. Press the MINUTE button (10) to set the minute while holding the SLEEP SET button (7). The sleep time will decrease from 59 minutes to zero.

Notes: To increase the sleep time over 1 hour, press the HOUR button (9) to set the hour while

holding the SLEEP SET button (7). The display will be changed to 1 hour and 59 minutes, which is the maximum sleep time setting. Press the MINUTE button (10) to decrease the minute.

4. Release the SLEEP SET button (7) when you finish to set the sleep time.

5. The radio will now operate until the sleep time has elapsed or may be switched off by pressing the

SNOOZE/SLEEP-OFF button (4).

Notes: Pressing the SLEEP SET button (7) again after setting the sleep time will reset the sleep time to

59 minutes. In this case, you need to set the sleep time again.

TO TUNR ON THE RADIO

The AM radio band uses an internal antenna to receive a signal. Rotate the unit to get the best reception for AM. For FM, ensure that the FM pig-tailed antenna is completely uncoiled and extended.

1. Set the ON/OFF/AUTO switch (1) to ‘ON’ position

2. Set the AM/FM switch (12) to the desired band.

3. Adjust the TUNING CONTROL knob (13) to select the desired station.

4. Adjust the VOLUME CONTROL knob (11).

5. To turn off the radio, set the ON/OFF/AUTO swtich (1) to ‘OFF’ position. If the radio does not s

witch off, this may be caused by inadvertent operation of the sleep function. To cancel this, press

SNOOZE/SLEEP-OFF button (4) once.

the

+ 1 hidden pages