JVC UXF-3 Service manual
SERVICE MANUAL
MICRO COMPONENT SYSTEM
MB743<Rev.003>20106SERVICE MANUAL
UX-F3BA, UX-F3BB, UX-F3BC, UX-F3BE,
UX-F3BEN, UX-F3BEV, UX-F3BJ, UX-F3BUJ,
UX-F3HB, UX-F3HE, UX-F3HEN, UX-F3HEV
SP-UXF3B
CA-UXF3B
CA-UXF3H
SP-UXF3B
SP-UXF3H
except UX-F3BJ/C
COPYRIGHT © 2010 Victor Company of Japan, Limited
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
SP-UXF3H
except
UX-F3BJ/C
TABLE OF CONTENTS
1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
COPYRIGHT © 2010 Victor Company of Japan, Limited
No.MB743<Rev.003>
2010/6
SPECIFICATION
Main unit (CA-UXF3B/CA-UXF3H) For B.E.EN.EV For J.C
General
Power source AC 230 V , 50 Hz AC 120 V , 60 Hz
Power consumption (at operation) 40 W
Power consumption (on standby) 1.00 W or less
Dimensions (approx.) (W x H x D) 236 mm × 123 mm × 285 mm
(including projecting parts)
Mass (approx.) 2.0 kg 2.0 kg(4.5 lbs)
Amplifier
Output Power 60 W (30 W + 30 W) at 6 Ω (10% THD)
Audio Input AUDIO IN: Stereo mini (
Speaker impedance 6 Ω - 16 Ω
Tuner
FM frequency 87.50 MHz - 108.00 MHz
USB (Only Europe)
USB specification Compatible with USB 2.0 Full Speed
Compatible device Mass storage class
Compatible system FAT16, FAT32
Output power DC 5 V 500 mA
iPod
Output power DC 5 V 500 mA
Video out Composite
Speaker(SP-UXF3B/SP-UXF3H)
Speaker type Bass-reflex type
Tweeter 4 cm 4 cm(1-5/8“)
Woofer 12 cm 12 cm(4-3/4“)
Impedance 6 Ω
Dimensions (approx.) (W x H x D) 141 mm × 250 mm × 181 mm
(including projecting parts)
Mass (approx.) 1.8 kg each 1.7 kg (3.8 lbs) each
Ø 3.5 mm)
236 mm × 123 mm × 285 mm
(9-5/16“×4-7/8“×11-1/4“)
(including projecting parts)
141 mm × 250 mm × 181 mm
(5-9/16“×9-7/8“×7-3/16“)
(including projecting parts)
Design and specifications are subject to change without notice.
1-2 (No.MB743<Rev.003>)
UX-F3BA/UX-F3BUJ
General
Power source For Australian model AC 240 V , 50 Hz
For another model
Power consumption (at operation) 40 W
Power consumption (on standby) 1.00 W or less
Dimensions (approx.) (W × H × D) 236 mm × 123 mm ×~ 285 mm (including projecting parts)
Mass (approx.) 2.0 kg
Amplifier
Output Power 60 W (30 W + 30 W) at 6 Ω (10% THD)
Audio Input AUDIO IN: Stereo mini (
Speaker impedance 6 Ω - 16 Ω
Tuner
FM frequency 87.50 MHz - 108.00 MHz
USB
USB specification Compatible with USB 2.0 Full Speed
Compatible device Mass storage class
Compatible system FAT16, FAT32
Output power DC 5 V 500 mA
iPod
Output power DC 5 V 500 mA
Video out Composite
Speaker(SP-UXF3B)
Speaker type Bass-reflex type
Tweeter 4 cm
Woofer 12 cm
Impedance 6 Ω
Dimensions (approx.) (W × H × D) 141 mm × 250 mm × 181 mm (including projecting parts)
Mass (approx.) 1.8 kg each
AC 110 V - 127 V / 220 V - 240 V adjustable with voltage selector, 50/60 Hz
Ø 3.5 mm)
Design and specifications are subject to change without notice.
(No.MB743<Rev.003>)1-3
SECTION 1
PRECAUTION
1.1 Safety Precautions
(1) This design of this product contains special hardware and
many circuits and components specially for safety purposes. For continued protection, no changes should be made
to the original design unless authorized in writing by the
manufacturer. Replacement parts must be identical to
those used in the original circuits. Services should be performed by qualified personnel only.
(2) Alterations of the design or circuitry of the product should
not be made. Any design alterations of the product should
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the
manufacture of responsibility for personal injury or property
damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the
protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special
safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features
are identified by shading on the schematics and by ( ) on
the Parts List in the Service Manual. The use of a substitute
replacement which does not have the same safety characteristics as the recommended replacement parts shown in
the Parts List of Service Manual may create shock, fire, or
other hazards.
(4) The leads in the products are routed and dressed with ties,
clamps, tubings, barriers and the like to be separated from
live parts, high temperature parts, moving parts and/or
sharp edges for the prevention of electric shock and fire
hazard. When service is required, the original lead routing
and dress should be observed, and it should be confirmed
that they have been returned to normal, after reassembling.
(5) Leakage shock hazard testing
After reassembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads,
headphone jack, control shafts, etc.) to be sure the product
is safe to operate without danger of electrical shock.Do not
use a line isolation transformer during this check.
• Plug the AC line cord directly into the AC outlet. Using a
"Leakage Current Tester", measure the leakage current
from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the
chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.).
• Alternate check method
Plug the AC line cord directly into the AC outlet. Use an
AC voltmeter having, 1,000Ω per volt or more sensitivity
in the following manner. Connect a 1,500Ω 10W resistor
paralleled by a 0.15µF AC-type capacitor between an ex-
posed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC
voltmeter.
Move the resistor connection to each exposed metal
part, particularly any exposed metal part having a return
path to the chassis, and measure the AC voltage across
the resistor. Now, reverse the plug in the AC outlet and
repeat each measurement. Voltage measured any must
not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5
mA AC (r.m.s.).
AC VOLTMETER
(Having 1000
ohms/volts,
or more sensitivity)
0.15 F AC TYPE
Place this
probe on
1500 10W
Good earth ground
1.2 Warning
(1) This equipment has been designed and manufactured to
meet international safety standards.
(2) It is the legal responsibility of the repairer to ensure that
these safety standards are maintained.
(3) Repairs must be made in accordance with the relevant
safety standards.
(4) It is essential that safety critical components are replaced
by approved parts.
(5) If mains voltage selector is provided, check setting for local
voltage.
1.3 Caution
Burrs formed during molding may be left over on some parts
of the chassis.
Therefore, pay attention to such burrs in the case of preforming repair of this system.
1.4 Critical parts for safety
In regard with component parts appearing on the silk-screen
printed side (parts side) of the PWB diagrams, the parts that are
printed over with black such as the resistor ( ), diode ( )
and ICP ( ) or identified by the " " mark nearby are critical
for safety. When replacing them, be sure to use the parts of the
same type and rating as specified by the manufacturer.
(This regulation dose not Except the J and C version)
each exposed
metal part.
1-4 (No.MB743<Rev.003>)
1.5 Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.5.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron palate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.6 Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
(No.MB743<Rev.003>)1-5
1.7 Important for laser products
1.CLASS 1 LASER PRODUCT
2.CAUTION :
(For U.S.A.) Visible and/or invisible class II laser radiation
when open. Do not stare into beam.
(Others) Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
3.CAUTION : Visible and/or invisible laser radiation when
open and inter lock failed or defeated. Avoid direct
exposure to beam.
4.CAUTION : This laser product uses visible and/or invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
!
Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
REPRODUCTION AND POSITION OF LABELS and PRINT
WARNING LABEL and PRINT
1-6 (No.MB743<Rev.003>)
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
SECTION 3
DISASSEMBLY
3.1 Main body (Used model: UX-F3E)
3.1.1 Removing the Top cover (See Fig.1, 2, 3, 4)
(1) Remove the four screws A attaching the Top cover. (See
Fig.1)
(3) Remove the three screws D, three screws E and one screw
F attaching the Top cover. (See Fig.3)
A
A
Fig.1
(2) Remove the two screws B and two screws C attaching the
both side of the Top cover. (See Fig.2)
B
E
F
D
Fig.3
(4) Disengaged three hooks a engaged Top cover. (See Fig.4)
hook
a
C
Fig.4
Fig.2
(No.MB743<Rev.003>)1-7
3.1.2 Removing the iPod bracket (See Fig.5, 6)
(1) Disconnect the card wires from iPod board connected to
connectors CN803
Fig.5)
(2) Remove the four screws G attaching the iPod bracket.
(See Fig.5)
and CN804 of the Main board. (See
(10) Remove the five screws H attaching the Main board.
CN604 CN605
CN606
H
CN602
CN601
H
GG
3.1.4 Removing the SMPS board (See Fig.8)
(1) Disconnect the connector wire from Display board connect-
CN803CN804
Fig.5
(3) Turn overt the iPod bracket; disconnect the connector wire
from Display board connected to connector CON202
LED board. (See Fig.6)
CON202
Fig.6
3.1.3 Removing the Main board (See Fig.7)
(1) Disconnect the connector wire from USB board connected
to connector CN606
(2) Disconnect the card wire from Tuner pack connected to
connector CN604 of the Main board.
(3) Disconnect the card wire from Upgrade board connected to
connector CN605
(4) Disconnect he card wire from Display board connected to
connector CN602
(5) Disconnect the connector wire from SMPS board connect-
ed to connector CN601
(6) Disconnect the connector wire from MPEG board connect-
ed to connector CN607
(7) Disconnect the card wire from MPEG board connected to
connector CN609
(8) Disconnect the connector wire from SMPS board connect-
ed to connector CN603
(9) Disconnect the connector wire from FAN connected to con-
nector CN612 of the Main board.
of the Main board.
of the Main board.
of the Main board.
of the Main board.
of the Main board.
of the Main board.
of the Main board.
of the
ed to connector CN902
(2) Remove the three screws J attaching the SMPS board.
J
3.1.5 Removing the Front panel (See Fig.9, 10)
(1) Disconnect the card wire from USB board connected to
connector CN108
(2) Disengaged two hooks b engaged both side of the Front
panel. (See Fig.9)
of the MPEG board. (See Fig.9)
b
(3) Disengage one hook c engaged Front panel. (See Fig.10)
hook
CN603CN612
Fig.7
of the SMPS board.
Fig.8
CN108hook
Fig.9
c
CN607
CN609
H
CN902
1-8 (No.MB743<Rev.003>)
Fig.10
3.1.6 Removing the DVD mechanism (See Fig.11. 12, 13)
(1) Remove the three screws K attaching the Rear cabi brack-
et. (See Fig.11)
K
K
Fig.11
(2) Disconnect the connector wire from MPEG board connect-
ed to connector of the Loading board. (See Fig.12)
(3) Disconnect the connector wire from MPEG board connect-
ed to connector of the Traverse mechanism. (See Fig.12)
Loading board
connector
Traverse mechanism
connector
3.1.7 Removing the MPEG board (See Fig.14)
(1) Remove the four screws M attaching the MPEG board.
M
M
Fig.14
3.1.8 Removing the LED board (See Fig.15)
(1) Remove the six screws N attaching the LED board.
Fig.12
(4) Disconnect the card wire from Pickup connected to con-
nector CN102
(5) Remove the four screws L attaching the DVD mechanism.
(See Fig.13)
of the MPEG board. (See Fig.13)
L
CN102
N
Fig.15
3.1.9 Removing the iPod board (See Fig.16)
(1) Remove the two screws P attaching the iPod board.
P
Fig.16
3.1.10 Removing the USB board (See Fig.17)
(1) Disconnect the connector wire from Display board connect-
ed to connector CN203
(2) Remove the two screws Q attaching the USB board.
of the USB board.
P
Q
L
Fig.13
CN203
Fig.17
(No.MB743<Rev.003>)1-9
3.1.11 Removing the Jack board (See Fig.18)
(1) Remove the two screws R attaching the Jack board.
R
Fig.18
3.1.12 Removing the Display board (See Fig.19)
(1) Remove the fifteen screws S attaching the Display board.
S
S
Fig.19
1-10 (No.MB743<Rev.003>)
SECTION 4
ADJUSTMENT
This service manual does not describe ADJUSTMENT.
SECTION 5
TROUBLESHOOTING
This service manual does not describe TROUBLESHOOTING.
(No.MB743<Rev.003>)1-11
Victor Company of Japan, Limited
Home Entertainment Business Division Personal AV Operation 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
(No.MB743<Rev.003>)
Printed in Japan
VSE
REVISION INFORMATION
MICRO COMPONENT SYSTEM
UX-F3BB, UX-F3BC, UX-F3BE, UX-F3BEN,
UX-F3BEV, UX-F3BJ, UX-F3HB, UX-F3HE,
UX-F3HEN, UX-F3HEV
■ OVERVIEW
Add UX-F3BC and UX-F3BJ.
■ DETAILS
COVER SECTION
Title Line No.MB743<Rev.001> No.MB743<Rev.002> Description
Revision Rev.001 Rev.002
Issue Date 2010/05 2010/06
Model No. UX-F3BB, UX-F3BE, UX-F3BEN,
Cover Illustration ILLUSTRATION(mb743_0001.png) ILLUSTRATION(mb743_0001.png)
SPECIFICATION 2
4
7
8
15
25
UX-F3BEV, UX-F3HB, UX-F3HE,
UX-F3HEN, UX-F3HEV
Main unit (CA-UXF3B/CA-UXF3H)
Power source
AC 230 V , 50 Hz
Dimensions (approx.) (W x H x D)
236 mm × 123 mm × 285 mm
(including projecting parts)
Mass (approx.)
2.0 kg
USB
Tweeter
4 cm
UX-F3BB, UX-F3BC, UX-F3BE, UX-F3BEN,
UX-F3BEV, UX-F3BJ, UX-F3HB, UX-F3HE,
UX-F3HEN, UX-F3HEV
Main unit (CA-UXF3B/CA-UXF3H)
For B.E.EN.EV
For J.C
Power source
AC 230 V , 50 Hz
AC 120 V , 60 Hz
Dimensions (approx.) (W x H x D)
236 mm × 123 mm × 285 mm (including
projecting parts)
236 mm × 123 mm × 285 mm (9-5/16"×47/8"×11-1/4")(including projecting parts)
Mass (approx.)
2.0 kg
2.0 kg(4.5 lbs)
USB (Only Europe)
Tweeter
4 cm
4 cm(1-5/8")
COPYRIGHT © 2010 Victor Company of Japan, Limited
MB743-R002
2010/06
Title Line No.MB743<Rev.001> No.MB743<Rev.002> Description
26
28
29
Woofer
12 cm
Dimensions (approx.) (W x H x D)
141 mm × 250 mm × 181 mm
(including projecting parts)
Mass (approx.)
1.8 kg each
Woofer
12 cm
12 cm(4-3/4")
Dimensions (approx.) (W x H x D)
141 mm × 250 mm × 181 mm (including
projecting parts)
141 mm × 250 mm × 181 mm (5-9/16"×97/8"×7-3/16")(including projecting parts)
Mass (approx.)
1.8 kg each
1.7 kg (3.8 lbs) each
STANDARD SCHEMATIC DIAGRAMS
Schematic Diagram
Diagram Name No.MB743<Rev.001> No.MB743<Rev.002> Description
Menu USB & SD section USB & SD section (for Except UX-F3BC,BJ)
Printed Circuit Board
Diagram Name No.MB743<Rev.001> No.MB743<Rev.002> Description
Menu USB board USB board (for Except UX-F3BC,BJ)
PARTS LIST
MODEL No. LIST
Model No. No.MB743<Rev.002>
UX-F3BB 01
UX-F3BC 02
UX-F3BE 03
UX-F3BEN 04
Model No. No.MB743<Rev.002>
UX-F3BEV 05
UX-F3BJ 06
UX-F3HB 07
UX-F3HE 08
Model No. No.MB743<Rev.002>
UX-F3HEN 09
UX-F3HEV 0A
General Assembly [M1MM]
Symbol or
!
M1MM 1 ------------ CD5501091400200 DISPLAY LENS (Addition) 1 02,06
M1MM 3 ------------ CD6021226060110 SCREW (Addition) 2 02,06
M1MM 6 ------------ CD5001091400200 FRONT CABINET (Addition) 1 02,06
M1MM 9 ------------ CD5902091400400 POWER BTN (Addition) 1 02,06
M1MM 13 ------------ CD6013226080100 SCREW (Addition) 13 02,06
M1MM 14 ------------ CD5633091800101 REAR CABI BKT (Addition) 1 02,06
M1MM 21 ------------ CD5002091400200 REAR CABINET (Addition) 1 02,06
M1MM 22 ------------ CD5201091400100 CD DOOR (Addition) 1 02,06
M1MM 29 ------------ CD5902091400500 CD PLAY BTN (Addition) 1 02,06
M1MM 30 ------------ CD5902091400800 TUNER BTN (Addition) 1 02,06
M1MM 31 ------------ CD5902091400900 iPod A PLAY BTN (Addition) 1 02,06
M1MM 32 ------------ CD5902091401000 iPod B PLAY BTN (Addition) 1 02,06
M1MM 37 ------------ CD5002091400301 BOTTOM CABINET (Addition) 1 02,06
M1MM 48 ------------ CD6013230060300 SCREW (Addition) 1 02,06
M1MM 51 ------------ CD5631091400300 iPod BRACKET (Addition) 1 02,06
! M1MM 57 ------------ CD2901212508040 AC CORD (Addition) 1 02,06
M1MM 59 ------------ CD7111091400200 RATING LABEL (Addition) 1 02,06
M1MM 73 ------------ CD3002150080930 FFC CABLE (Addition) 2 02,06
M1MM 77 ------------ CD3002100160900 FFC CABLE (Addition) 1 02,06
<Rev.001> <Rev.002>
Part No.
Part Name Description Qty Models
2 (MB743-R002)
Packing and Accessories [M3MM]
Symbol or
!
M3MM A1 ------------ CD7202091400500 INST BOOK (Addition) 1 02,06
M3MM A2 ------------ CD7202091401800 INST BOOK (Addition) 1 02
M3MM A6 ------------ CD7201091400400 SAFETY SHEET (Addition) 1 02,06
M3MM A7 ------------ ------------ WARRANTY CARD (Addition) 1 02,06
M3MM A8 ------------ CD7201081100200 REGIS. CARD (Addition) 1 02,06
M3MM A10 ------------ CD1901000012400 REMOCON UNIT (Addition) 1 02,06
M3MM A13 ------------ CD7201081200600 SAFETY INST (Addition) 1 02,06
M3MM P1 ------------ CD7603091400200 CARTON (Addition) 1 02,06
M3MM P10 ------------ CD7215091800200 FLOUR PAPER (Addition) 2 02,06
<Rev.001> <Rev.002>
Part No.
Part Name Description Qty Models
Electrical parts list Main board [01]
Symbol or
!
01 D801 ------------ CD1322058170010 SCHOTTKY DIODE (Addition) 1 02,06
01 C780 ------------ CD1129226044120 C CAPACITOR (Addition) 1 02,06
01 C781 ------------ CD1129226044120 C CAPACITOR (Addition) 1 02,06
01 C796 ------------ CD1221000042050 C RESISTOR (Addition) 1 02,06
01 C797 ------------ CD1221000042050 C RESISTOR (Addition) 1 02,06
01 R780 ------------ CD1221103052020 C RESISTOR (Addition) 1 02,06
01 R782 ------------ CD1221104052020 C RESISTOR (Addition) 1 02,06
01 L824 ------------ CD1221000052020 C RESISTOR (Addition) 1 02,06
01 L825 ------------ CD1221000052020 C RESISTOR (Addition) 1 02,06
01 CF05 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
01 CV04 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
01 CV07 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
01 EC601 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
01 EC602 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
01 EC605 ------------ CD1132227053064 E CAPACITOR (Addition) 1 02,06
01 EC607 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
01 EC608 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
01 EC610 ------------ CD1132227053064 E CAPACITOR (Addition) 1 02,06
01 EC701 ------------ CD1132228073270 E CAPACITOR (Addition) 1 02,06
01 EC703 ------------ CD1132227053064 E CAPACITOR (Addition) 1 02,06
01 EC711 ------------ CD1132227053064 E CAPACITOR (Addition) 1 02,06
01 EC712 ------------ CD1132227053064 E CAPACITOR (Addition) 1 02,06
01 EC713 ------------ CD1132227053064 E CAPACITOR (Addition) 1 02,06
01 EC810 ------------ CD1132227053064 E CAPACITOR (Addition) 1 02,06
01 EC811 ------------ CD1132227053064 E CAPACITOR (Addition) 1 02,06
01 P601 ------------ CD3401000000420 PUSH TERMINAL (Addition) 1 02,06
01 P602 ------------ CD3401000000420 PUSH TERMINAL (Addition) 1 02,06
<Rev.001> <Rev.002>
Part No.
Part Name Description Qty Models
MPEG board [02]
Symbol or
!
02 C139 ------------ CD1121300081020 C CAPACITOR (Addition) 1 02,06
02 C140 ------------ CD1121300081020 C CAPACITOR (Addition) 1 02,06
02 R110 ------------ CD2721601020030 FERRITE BEADS (Addition) 1 02,06
<Rev.001> <Rev.002>
Part No.
Part Name Description Qty Models
Display board [03]
Symbol or
!
03 C306 ------------ CD1121102083020 C CAPACITOR (Addition) 1 02,06
03 C507 ------------ CD1132227053064 E CAPACITOR (Addition) 1 02,06
03 C510 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
03 C513 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
03 R503 ------------ CD1221181022050 C RESISTOR (Addition) 1 02,06
03 R536 ------------ CD1221203062020 C RESISTOR (Addition) 1 02,06
03 R544 ------------ CD1221000042050 C RESISTOR (Addition) 1 02,06
03 ZD506 ------------ CD1323000510050 Z DIODE (Addition) 1 02,06
<Rev.001> <Rev.002>
Part No.
Part Name Description Qty Models
(MB743-R002)3
SMPS board [04]
Symbol or
!
04 Q901 ------------ CD1414005600011 TRANSISTOR (Addition) 1 02,06
04 D904 ------------ CD1311001070050 DIODE (Addition) 1 02,06
04 C924 ------------ CD1132108053161 E CAPACITOR (Addition) 1 02,06
04 C925 ------------ CD1132108053161 E CAPACITOR (Addition) 1 02,06
04 C926 ------------ CD1132337063220 E CAPACITOR (Addition) 1 02,06
04 C927 ------------ CD1132337063220 E CAPACITOR (Addition) 1 02,06
04 C928 ------------ CD1132337063220 E CAPACITOR (Addition) 1 02,06
04 C931 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
04 R916 ------------ CD1231039022000 RESISTOR (Addition) 1 02,06
04 R917 ------------ CD1231039022000 RESISTOR (Addition) 1 02,06
04 CN901 ------------ CD3101100221010 HEADER (Addition) 1 02,06
04 PIN3 ------------ CD3401000000420 PUSH TERMINAL (Addition) 1 02,06
04 PIN4 ------------ CD3401000000420 PUSH TERMINAL (Addition) 1 02,06
04 PIN5 ------------ CD3401000000420 PUSH TERMINAL (Addition) 1 02,06
04 ZD901 ------------ CD1323003620010 ZENER DIODE (Addition) 1 02,06
04 ZD902 ------------ CD1323003620010 ZENER DIODE (Addition) 1 02,06
<Rev.001> <Rev.002>
Part No.
Part Name Description Qty Models
iPod board [06]
Symbol or
!
06 C809 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
06 C818 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
06 C833 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
06 C871 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
06 C874 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
06 C884 ------------ CD1132107053063 E CAPACITOR (Addition) 1 02,06
<Rev.001> <Rev.002>
Part No.
Part Name Description Qty Models
LED board [07]
Symbol or
!
07 ZD201 ------------ CD1313055270010 Z DIODE (Addition) 1 02,06
07 ZD202 ------------ CD1313055270010 Z DIODE (Addition) 1 02,06
<Rev.001> <Rev.002>
Part No.
Part Name Description Qty Models
Victor Company of Japan, Limited
Home Entertainment Business Division Personal AV Operation 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
(MB743-R002)
Printed in Japan
No.MB743<Rev.001> VSE
REVISION INFORMATION
MICRO COMPONENT SYSTEM
UX-F3BA, UX-F3BB, UX-F3BC, UX-F3BE,
UX-F3BEN, UX-F3BEV, UX-F3BJ, UX-F3BUJ,
UX-F3HB, UX-F3HE, UX-F3HEN, UX-F3HEV
■ OVERVIEW
Add UX-F3BA and UX-F3BUJ.
■ DETAILS
COVER SECTION
Title Line No.MB743<Rev.002> No.MB743<Rev.003> Description
Revision Rev.002 Rev.003
Model No. UX-F3BB, UX-F3BC, UX-F3BE,
UX-F3BEN, UX-F3BEV, UX-F3BJ,
UX-F3HB, UX-F3HE, UX-F3HEN,
UX-F3HEV
Cover Illustration ILLUSTRATION(mb743_0001.png) ILLUSTRATION(mb743_0001.png)
33 -
34 -
35 -
36 -
37 -
38 -
39 -
40 -
UX-F3BA, UX-F3BB, UX-F3BC,
UX-F3BE, UX-F3BEN, UX-F3BEV,
UX-F3BJ, UX-F3BUJ, UX-F3HB,
UX-F3HE, UX-F3HEN, UX-F3HEV
UX-F3BA/UX-F3BUJ
General
Power source
For Australian model
AC 240 V , 50 Hz
For another model
AC 110 V - 127 V / 220 V - 240 V
adjustable with voltage selector, 50/60 Hz
Power consumption (at operation)
40 W
Power consumption (on standby)
1.00 W or less
Dimensions (approx.) (W × H × D)
236 mm × 123 mm ×~ 285 mm (including
projecting parts)
Mass (approx.)
2.0 kg
COPYRIGHT © 2010 Victor Company of Japan, Limited
MB743-R003
2010/06
Title Line No.MB743<Rev.002> No.MB743<Rev.003> Description
41 -
42 -
43 -
44 -
45 -
46 -
47 -
48 -
49 -
50 -
51 -
52 -
53 -
54 -
55 -
56 -
57 -
58 -
59 -
60 -
61 -
63 - Design and specifications are subject to
Amplifier
Output Power
60 W (30 W + 30 W) at 6 Ω (10% THD)
Audio Input
AUDIO IN: Stereo mini (Φ 3.5 mm)
Speaker impedance
6 Ω - 16 Ω
Tuner
FM frequency
87.50 MHz - 108.00 MHz
USB
USB specification
Compatible with USB 2.0 Full Speed
Compatible device
Mass storage class
Compatible system
FAT16, FAT32
Output power
DC 5 V 500 mA
iPod
Output power
DC 5 V 500 mA
Video out
Composite
Speaker(SP-UXF3B)
Speaker type
Bass-reflex type
Tweeter
4 cm
Woofer
12 cm
Impedance
6 Ω
Dimensions (approx.) (W × H × D)
141 mm × 250 mm × 181 mm (including
projecting parts)
Mass (approx.)
1.8 kg each
change without notice.
2 (MB743-R003)
Loading...