JVC TS-C420P9W Service Manual

Download

Page 1

52109200304

SERVICE MANUAL

WALL MOUNTING UNIT

TS-C420P9W

Mass: 10 kg

ngles of Inclination: 0 , 5 , 10 , 15 , 20

Wall Mounting Holes

13 13

4-R10

470

400

340

130

4-R10

42-inch Display

300

89 49

TS-C420P9W

110 2 0

20 20

190 170

499

E F

131

6-R10

E Section Details

1 113

110 50

20 160

180

60 120 120

568

13 1

(Outer edge)

6-R10

F Section Details

131

8.5 20

159.5 101.5 140 81.5 16.5

Wall Mounting Unit Exterior

(Units in millimeters)

TABLE OF CONTENTS

1 ASSEMBLY AND MOUNTING INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

2 PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

No.52109

2003/04

Page 2

TS-C420P9W

ASSEMBLY AND MOUNTING INSTRUCTIONS

ENGLISH

AIS

DEUTSCHESPAÑOL ITALIANO

Assembly and Mounting Instructions

For Assembly By Authorized Service Personnel Only

Consult authorized service personnel for the installation of this unit. Installation

instructions must be followed precisely in order to prevent accidents. We are

selling this product with the understanding that it will be assembled and installed

by properly trained and qualified service personnel.

FRAN

Danger

We are not liable for any damage caused by faulty assembly,

faulty wall mounting, insecure wall mounting, misuse,

alterations, or natural disasters.

This unit weighs approx. 45 kg (approx. 99 lbs.) including plasma display monitor.

Incomplete or inadequate mounting of this unit to the wall may cause it to fall

down, resulting in potentially fatal accidents.

Please consult authorized service personnel for the installation of this unit.

89 49

300

20°



42-inch Display

16.5

470

400

2-φ5

4-R10

130

340

Wall Mounting Holes

4-R10

Mass: 10 kg

Angles of Inclination: 0°, 5°, 10°, 15°, 20°

2-φ5

8190

Wall Mounting Unit

499

81.5159.5

2-φ8

140101.5

110 2016020

170131

2020

Ｆ

F Section

Ｅ

E Section

8.5

50110

Mounting a plasma display television requires specific technical knowledge. Do not attempt to mount the unit by yourself.

Please be aware that screw holes and anchor bolts will remain in the wall surface if the Wall Mounting Unit is removed

after having been mounted to the wall.

Thank you for purchasing this Wall Mounting Unit.

We recommend that you read this manual thoroughly before use in order to familiarize yourself with this unit.

Please store this manual in a safe place after reading it.

TS-C420P9W

Long-term use of the plasma display may result in discoloration of the wall surface due to heat/air emitted by the display.

•

2-φ8

Wall Mounting Unit Exterior

120180

6-R10

(Outer edge)

568

60 120

6-R10

2-φ5

1313

F Section Details

2-φ5

E Section Details

2-φ5

13 1

2-φ8

2-φ8 1

(Units in millimeters)

1 13

13 1

2-φ8

VICTOR COMPANY OF JAPAN, LIMITED

1-2 (No.52109)

Page 3

TS-C420P9W

ENGLISH

Warning

Mounting the Wall Unit

The Wall Mounting Unit should be mounted to a wall that can adequately

hold the total weight of the plasma display and the Wall Mounting Unit

over a long period of time and which can adequately withstand

earthquakes, conceivable vibrations, and other external forces.

Improper installation may cause the plasma display to fall down, resulting

in physical injury.

Mounting On Wooden Walls

The weight of the unit should be borne by the wall posts or studs, and

these should be reinforced if insufficiently strong. Do not install the Wall

Mounting Unit on walls made of plasterboard or thin plywood. Use the

commercially sold screws best suited for the wall structure and material.

Mounting On Concrete Walls

Use commercially sold wall anchors capable of supporting the weight of

the plasma display.

Do not install the Wall

Mounting Unit in a

location which is hot or

humid or which may

become wet, as the

presence of excessive

moisture may lead to

fire or electric shock.

Do not install the Wall

Mounting Unit near the

blower or air inlet of an air

conditioner.

Do not install the unit in a

location with a large

amount of dust, soot, or

cigarette smoke, as this

may lead to fire.

Do not block the

ventilation holes, and be

sure to leave sufficient

space around the unit

for ventilation.

Inadequate ventilation may

cause the unit interior to

overheat, leading to fire.

Plasterboard/Thin Plywood

Do not install the Wall

Mounting Unit in a

location subject to

frequent vibration, impact

or other external forces.

The unit may fall down or

be damaged, causing

physical injury.

Do not install the unit in a

location where people

may hang on it or lean

against it.

Doing so may cause the

unit to fall down or be

damaged, resulting in

injury.

Do not install the unit in

a location exposed to

direct sunlight or strong

light, as viewing the

plasma display in an

overly bright

environment can be

tiring for the eyes.

Do not install the Wall

Mounting Unit on a

non-vertical wall.

The unit interior may

overheat, resulting in fire,

or the unit may fall down,

causing physical injury.

At least

15 cm

At least

20 cm

Explanation of symbols

Safety Precautions

The following section describes the symbols used in this manual. Read this section prior to using the product for correct usage.

The following items contain information for your safety. Follow these precautions precisely.

Warning and Caution are defined as follows:

Danger

Improper handling in disregard of these notices may result in danger of death or bodily harm.

Improper handling in disregard of these notices may result in bodily injury and even death.

Mishandling of the unit in disregard of these notices may result in bodily injury or damage to

Danger

Warning

Caution

Examples:

the unit.

The indicates caution (including warning or danger).

indicates a prohibition, with the specific action indicated either in the circle itself (the

The

symbol at left means "Do Not Disassemble"), or in the accompanying text.

This unit weighs approx. 45kg (approx. 99 lbs.), including display monitor. Improper assembly or

installation may cause the unit to fall when it is mounted, which may result in fatal accidents. To

prevent this happening, check the strength of the materials in the mounting surface, and have at least

two persons carry out the installation in a suitable location. Check the material strength again after

● Consult authorized service personnel for the installation and attachment of this unit to the wall.

mounting as well.

Assembly and Mounting Warnings

Warning

bodily injury due to the display monitor and stand toppling over.

● Using display monitors other than those authorized by Victor with the unit may result in damage or

mounting falling down, potentially causing damage or bodily injury.

or electric shock.

● Assemble all bolts, nuts and screws securely. Failure to do so may result in display monitor and wall

● Avoid placing heavy objects on the power cord, as damage to the power cord may result, causing fire

hand as appropriate for the mounting location.

● This unit does not come with anchor bolts for securing it to walls, etc. Be sure you have materials on

(No.52109)1-3

Page 4

TS-C420P9W

q Frame

ENGLISH

Wall Mounting Unit

Flat Washer

Spring Washer

the plasma display to the Wall Mounting Unit. Be sure to keep them in a safe place.

＊ These Frame Fastening Screws, Spacer Rings, Flat Washers, and Spring Washers will be used when attaching

The Wall Mounting Unit is sold with Frame q and Wall Mounting Unit w fixed together. The following steps should

Washer, and Spring Washer.

be performed before attaching the plasma display.

1. Take the left and right Frame Fastening Screw Components and remove the Fastening Screw, Spacer Ring, Flat

Frame Fastening Screw

Spacer Ring

Angle Adjustment Lever

Caution

Frame Removal

Lever Screws

w Wall Mounting Unit

q Frame

Frame q from the Wall Mounting Unit w.

2. Push in the heads of the left and right Frame Removal Lever Screws a and lift up section b to remove the

e X 8

Lever Lock Screw

r Angle Adjustment

35-inch

Frame Rotation Shaft

X 12

Screws (left/right)

Spacer Rings (left/right)

Frame Attachment Lever Screws

Frame

Rotation Jaw

Plasma Display

e X 10

PD-42D30ES series

( )

42-inch PD-42DX series

Plasma Display

e Screw (M5 X 30) .......................... 12

r Screw (M5 X 20) ............................ 1

Parts bag

contains:

1-4 (No.52109)

installation (i.e., exposed or severed wiring) may result in fire or electric shock.

working under unsuitable conditions.

● Consult authorized service personnel for electrical work. Using power cords damaged during

electric shock may result.

● Conduct the work with adequate working space. Damage or bodily injury may result from

● Avoid mounting this unit in areas where there is electrical wiring or water pipes, as fire or

Tools Required for Assembly:

1. Type 2 Philips Screwdriver (+)

2. Type 2 Philips Screwdriver (+) with 300mm (approx. 12-inch) or longer shaft

50-inch

Frame Fastening Screws left/right

Plasma Display

(Spacer Ring + Flat Washer + Spring Washer)

e X 10

42-inch

Plasma Display

q Frame................................................................... 1

w Wall Mounting Unit ............................................... 1

Page 5

TS-C420P9W

ENGLISH

3. Identify the Rotation Shaft Screws of the Wall Mounting Unit.

Check that the left and right Rotation Shaft Screws are secure, as the Rotation Jaw of the Frame (attached to

the plasma display) will be inserted into the Rotation Shaft Screw Component of the Wall Mounting Unit w.

Avoid inserting fingers into the gap between the Frame and the Wall Mounting Unit when

putting these together, as fingers will get trapped, causing injury.

Caution

4. Attach the plasma display to the Wall Mounting Unit.

＊ This task must be performed by at least two persons.

Insert the Rotation Jaw of the Frame q (attached to the plasma display) securely into the Rotation Shaft

Screw Component of the Wall Mounting Unit, then raise up the plasma unit on this axis and push it into place

- it should lock with a clicking sound. Before releasing the unit, check that the plasma display is securely fitted

and does not rattle and loose.

w Wall Mounting Unit

Rotation Shaft Screw Component

Rotation Shaft

Screw

Spacer Ring

Rotation Jaw

q Frame Rotation Jaw

Fasten all bolts and screws securely. Failure to do so may cause the plasma display and Wall Mounting

Unit to fall down, causing potentially fatal accidents.

Improper positioning/installation of the Wall Mounting Unit on the wall may cause the unit to fall down.

Check the structure, material, and strength of the mounting surface thoroughly and carry out installation

in a suitable location. Failure to do so may cause the plasma display and Wall Mounting Unit to fall

down, leading to potentially fatal accidents.

Danger

The unit should be attached using the method most suited to the wall structure.

＊ When anchor nuts/bolts are to be inserted into the wall before mounting, either align the actual Wall

Instructions for Assembly

Mounting the Plasma Display

1. Attach the Wall Mounting Unit w to the surface of the wall.

35-inch

w Wall Mounting Unit

PD-42D30ES series

( )

42-inch PD-42DX series

Wall Surface Side

(Wall Mounting Unit)

Position of Wall

Mounting Holes

Mounting Unit w with the wall to determine the positioning of the holes or calculate the positioning of the

holes using a dimensional drawing of the unit before installing the anchor nuts/bolts.

Twelve screws (M5X30) e should be used to attach the Frame q to a 50-inch plasma display, Ten screws

(M5X30) e should be used to attach the Frame q to a 42-inch plasma display and eight screws (M5X30) e

2. Attach Frame q to the plasma display.

42-inch

A soft mat or similar material should be laid out to prevent damage to the plasma display during attachment to

the unit.

＊

should be used to attach the Frame q to a 35-inch plasma display.

50-inch

Plasma Display

eScrews (M5X30) x 8

eScrews (M5X30) x 10

Plasma Display

eScrews (M5X30) x 10

Plasma Display

eScrews (M5X30) x 12

Align the first Mounting Hole

(No.52109)1-5

Page 6

TS-C420P9W

ENGLISH

Angle Adjustment

Lever

0°

5°

10°

15°

20°

Grip the plasma display firmly while adjusting the angle, as the display could tip over and cause

injury.

Caution

＊ The angle of the Wall Mounting Unit can be adjusted to 0°, 5°, 10°, 15°, and 20°.

Brace the upper middle part of the plasma display with one hand and push the Angle Adjustment Lever to the

left with the other hand. The plasma display will tip forward. Release the Angle Adjustment Lever when the

Adjusting the Angle of the Plasma Display

desired angle setting is reached.

1. Adjust the angle of the plasma display.

Frame Fastening

Screw Component

Once the plasma display has been set at the desired angle, fasten the Angle Adjustment Lever with the screw

(M5X20) r.

2. Fix the Angle Adjustment Lever.

Frame Fastening Screw

Spring Washer

Flat Washer

Spacer Ring

Note: do not fasten the Angle Adjustment Lever if the power cord or system cables have yet to be attached.

r Screw (M5X20) x 1

rattle and loose.

＊ Check to make sure that the Angle Adjustment Lever is securely fastened and the plasma display does not

＊

1-6 (No.52109)

Avoid inserting fingers into the gap between the Frame and the Wall Mounting Unit when

putting these together, as fingers will get trapped, causing injury.

Flat Washer

Caution

Combine the Frame Fastening Screws, Spacer Rings, Flat Washers, and Spring Washers (from the two pairs of

Frame Fastening Screw Components that were put aside when detaching the Frame q from the Wall Mounting

Unit w) as shown below and fasten them securely using a screwdriver.

5. Fix the Frame and Wall Mounting Unit.

Spacer Ring

Spring Washer

Frame Fastening Screw

＊ Confirm that all of the parts are securely fastened and do not rattle and loose.

Page 7

TS-C420P9W

ENGLISH

3. Remove the Rotation Shaft Screws and Spacer Rings at the bottom left and right of the Wall Mounting Unit.

＊ The Rotation Shaft Screws and the Spacer Rings will be used after the cables have been connected. Be sure

to keep them in a safe place.

Spacer Rings

Rotation Shaft Screws

Brace the plasma display when connecting the power cable or system cables. Failure to do so

may allow it to tip over, potentially causing injury.

Caution

4. Pull the plasma display forward.

Brace the bottom of the plasma display and push up the heads of the screws at the left/right of the Frame

Attachment Lever Screw component at the bottom of the Wall Mounting Unit, until the screws come into contact

with the Frame. The plasma display can now be pulled forward.

＊ This task must be performed by at least two persons.

Plasma Display

Frame

Wall Mounting Unit

Lateral View

Pull Forward

Frame Attachment Lever Screw

Component

Grip the plasma display firmly while connecting the power cord/system cables, as the display

may tip over and cause injury.

Caution

Connecting the Power Cord and System Cables

Check that the two Frame Fastening Screws on the upper left and right sides of the Wall Mounting Unit are

securely fastened.

1. Check the Frame Fastening Screws.

Frame Fastening Screws

Caution

If the Frame Fastening Screws are not

securely fastened the plasma display

may fall, causing potentially fatal injury.

Caution

Grip the plasma display as you adjust

the angle, as the plasma display may

tip over and cause injury.

20°

Adjustment Lever Lock Screw.

＊ If the Angle Adjustment Lever has already been fastened, perform this task after removing the Angle

to 20°.

2. Place one hand on top of the plasma display to steady it and with the other hand set the Angle Adjustment Lever

(No.52109)1-7

Angle Adjustment Lever

Lock Screw

Page 8

TS-C420P9W

ENGLISH

Angle Adjustment Lever

Caution

Grip the plasma display firmly as you

adjust the angle, as the display may

fall forward and cause injury.

0°

5°

10°

15°

20°

Hold the upper part of the plasma display with one hand and set the display to the desired angle with the other

hand, using the Angle Adjustment Lever on the Wall Mounting Unit.

7. Set the angle of the plasma display.

Brace the plasma display while connecting the power cord or system cables, as the display may

tip over, causing injury.

Once the angle of the plasma display has been set, fasten the Angle Adjustment Lever with the Screw (M5X20)

8. Fasten the Angle Adjustment Lever.

Rotation Shaft Screw

r Screw (M5X20) x 1

Rotation Shaft Screw

Spacer Ring

＊ Check to make sure that the lever is securely fastened and the plasma display does not rattle.

1-8 (No.52109)

Caution

5. Connect the power cable and system cables to the plasma display.

Push the bottom of the plasma display toward the Wall Mounting Unit to securely fasten the display to the Wall

Mounting Unit. Then, fasten the Rotation Shaft Screw Component at the bottom left/right of the Wall Mounting

Unit with the Rotation Shaft Screws and the Spacer Rings.

＊ Be careful not to let the cables become caught between the plasma display and the Wall Mounting Unit.

6. Fix the Plasma Display to the Wall Mounting Unit.

＊ This task must be performed by at least two persons.

Spacer Ring

Rotation Shaft Screw

Page 9

TS-C420P9W

ENGLISH

This task must be performed by at least two persons.

Danger

3. Remove the Frame Fastening Screws, Spacer Rings, Flat Washers, and Spring Washers of the two Frame

Fastening Screw Components at the upper left and right of the Wall Mounting Unit.

4. Push up the heads of the screws in the Frame Attachment Lever components at the bottom left and right of the

Wall Mounting Unit until they come into contact with the Frame. Then tilt the plasma display 90° forward and,

without changing the inclination of the plasma display, pull the display out horizontally.

Frame Fastening Screws

Frame Removal Lever Screws

This task must be performed by at least two persons.

Danger

＊ If the Angle Adjustment Lever has been fastened, remove the Angle Adjustment Lever Lock Screw before

1. Hold the upper middle of the plasma display and set the Angle Adjustment Lever to 0°.

performing this task.

Angle Adjustment

Lever

Angle Adjustment Lever

Lock Screw

Rotation Shaft Screws

fastened.

2. Confirm that the Frame Rotation Shaft Screws at the left and right bottom of the Wall Mounting Unit are securely

(No.52109)1-9

Page 10

TS-C420P9W

EXPLODED VIEW

PARTS LIST

42-inch Plasma Display

Frame

Wall Mounting Unit

(x5)

42-inch(PD-42DX, PD-42DXT, PD-42D30ES) Plasma Display

(x5)

Frame

(x5)

35-inch Plasma Display

EXPLODED VIEW PARTS LIST

Ref.No. Part No. Part Name Qty Description

1 PDP-414 SCREW 12 M5 × 30 2 QYSPSPD5020Z SCREW 1 M5 × 20 3 PDP-419 SCREW 4 M6 × 20 4 PDP-412 SPACER RING 2 5 PDP-422 SCREW 2 M5 × 25 6 PDP-411 SPACER RING 2 7 PDP-426 FLAT WASHER 2 8 PDP-428 SPRING WASHER 2

LC31937-005A CARTON LABEL 1 TS-C420P9W-AD INST BOOK 1 PDP-435 PACKING CASE 1

(x4)

Frame

(x4)

1-10 (No.52109)

Page 11

TS-C420P9W

(No.52109)1-11

Page 12

TS-C420P9W

VICTOR COMPANY OF JAPAN, LIMITED

AV & MULTIMEDIA COMPANY DISPLAY CATEGORY 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, Japan

(No.52109)

Printed in Japan

200304WPC