JVC LX-D1000 User Manual

INSTRUCTION MANUAL
FOR ASSEMBLY AND INSTALLATION OF
EF-L1000CG <METAL FIXTURES SUSPENDED FROM CEILING>
LCD Projector Compatible with Installation
Model Name: LX-D1000 (Body’s mass is 4.5 Kg)
For Selling and Installing Stores
Read this instruction manual carefully before assembly and/or installation. Be sure to carry out the work properly always with safety in mind.
Do not permit the customers to engaged in assembly and/or installation. Mak e sure that your custom­ers request you, the professional installers, for assembly and/or installation.
The total mass of the metal mixtures for the ceiling is 5.5 Kg.
DETAILS TO BE STRICTLY OBSERVED FOR SAFETY
Before assembly and/or installation, be sure to read carefully the “details to be strictly observed for safety.” The risk and its extent caused by erroneous handling are demarcated as follows:
WARNING
CAUTION
Carry out installation so that a safety rate definitely comes to more than 5 times.
Select a strong place where the mass of the LCD projector and the metal fixtures can be held sufficiently. If they are installed at a spot having insufficient strength, the metal fixtures attached to the ceiling can come off and fall, re­sulting in injury.
Take necessary measures to prevent any possible swing using wires, etc.
Otherwise, temblors and vibrations can result in falls, causing injury.
Probability that can result in critical consequences such as death or serious injury in case of erroneous handling.
Probability that can result in injury or damage of houses and/or household effects in case of erroneous han­dling.
WARNING
Be sure to carry out installation under a ceiling with a horizontal surface.
Avoid installation under an inclined or warped ceiling.
CAUTION
Pay attention not to allow any children hang onto the fixtures.
Otherwise, injury can result.
Be sure to install them at a place where there is no other appa­ratus such as a fire alarm, etc., or malfunction of appliances and instruments, etc., can result.
BHU30002-036-001
– 1 –
CHECK AND MAKE SURE
Check and confirm before assembly and/or installation that the following parts are packed along with the body as accessories:
CAUTION: When installing component parts, caution must be exercised not to use any parts except the ones packed with the body.
No. Names of parts
q Coupling plate 1 w Supporter for LCD projector 1 e Assembling bolts (M8 × 25) 4 r Rotary setscrews [E] (M5 × 10) 2 t Screws [A] (M4 × 12) 2 y Ceiling plate 1 u Inner pole 1 i Inner pole fixing plate 1 o Hexagon socket bolts (M5 × 10) 4 !0 Collar 1
Quantity
No. Names of parts
!1 Hexagon head bolts [C] (M10 × 65) 1 !2 Nut 1 !3 Washers (for M10) 2 !4 Screws [B] (M8 × 14) 2 !5 Hexagon wrench (for M5) 1 !6 Hexagon wrench (for M8) 1 !7 Rotary mini setscrews (M5 × 5) 2 !8 Hexagon socket bolts (M5 × 16) 4 !9 Washers (for M5) 4 @0 Nuts (for M5) 4
PROCEDURES FOR ASSEMBLY AND INSTALLATION (Refer to Fig. 3)
To begin with, determine the projection range, then the fixing posi-
1.
tion of the metal fixtures’ ceiling plate . (The projection lens center of the ceiling plate is apart about 24 mm from that of the LCD projector. Refer to Fig. 4)
Install the ceiling plate underneath the ceiling as illustrated in Fig. 3.
2.
For the size of the metal fixtures’ fixing hole, refer to Fig. 3-1. Use the fixing screw of the ceiling plate larger than M8.
WARNING: Check and make cer tain that there is a safety rate of more than 5 for the total mass of the metal fixtures including the LCD projector.
Turn the LCD projector over, and loosen only the angle adjuster lo-
3.
cated at the position illustrated in the figure. See Fig. 1. (At this time, take the sponge out from between the angle adjuster and the body.)
Fig. 1
(Bottom view of LCD projector)
Loosen this portion of the angle adjuster counterclockwise.
Quantity
Set the body’s plate to the LCD projector , and slide it in the direction
4.
indicated by the arrow mark. See Fig. 2. Insert the 2 screws [A] into the two holes provided at the bottom of
5.
the LCD projector, and tighten the angle adjuster. (See Fig. 2 and Fig. 3)
Set the supporter for the LCD projector from the bottom, tighten the
6.
screws [B], and secure the supporter.
Set the inner pole fixing plate and the inner pole temporarily with 4
7.
hexagon socket bolts (M5 × 10) as illustrated in Fig. 3, and insert the inner pole into the hole of the coupling plate.
Fix the inner pole fixing plate and the coupling plate with 4 hexagon
8.
socket bolts (M5 × 16), and tighten them with 4 nuts (for M4).
Adjust the holes of the inner pole and the ceiling plate, put on the
9.
collar, washer, and nut in the order as shown in Fig. 3, and fasten them with a hexagon bolt [C].
Make adjustments on the rotating direction of the entire body of the
10.
metal fixtures, and then tighten the 4 hexagon socket bolts (M5 ×
10) that were temporarily fixed as mentioned in Procedure 7 abov e.
Tighten the inner pole using 2 rotary setscrews [E], and furthermore
11.
secure the inner pole using 2 rotary mini screws.
Fig. 2
t Screws [A] (M4 × 12)
Body’s plate
Angle adjuster
Slide
(*) Fastening bolt to
install arm (1 bolt)
WARNING
(*) Part
: The asterisked fastening bolt to install an arm (1 bolt)
is built in to constitute a part of the body’s plate.
: Never remove the above-mentioned bolt under any
circumstances since it is absolutely required to ensure safety.
– 2 –
Fig. 3 ASSEMBLY
y Ceiling plate
!8 4 hexagon socket
bolts (M5 × 16)
i Inner pole
fixing plate
@0 4 nuts (for M5)
!9 4 washers
(for M5)
o 4 hexagon socket
bolts (M5 × 10)
(*) Fastening bolts for
body’s plate (4 bolts)
!3 Washers (for M10)
u Inner pole
Air inlet ()
!2 Nut
t 2 screws [A]
(M4 × 12)
LCD projector
q Coupling plate
!7 2 rotary mini
setscrews (M5 × 5)
!1 Hexagon head bolts
[C] (M10 × 65)
!3 Washer (for M10)
!0 Collar
e 4 assembling bolts (M8 × 25)
Body’s plate
(*) Holder plates (2 plates)
(*) Fastening bolts for
holder plate (8 bolts)
Fig. 3-1
150
(109.6)
Size of fixing hole of base metal fixtures
r 2 rotary setscrews [E] (M5 × 10)
20
(109.6)
!5 Hexagon wrench (accessory)
Hexagon socket bolts for M5
10
155
150
!4 2 screws [B] (M8 × 14)
Note:
w Supporter for LCD projector
Unit of indicated dimensions (mm)
WARNING
Air inlet: This is an inlet to bring cool air into the LCD projector. Do not cover it with a lid, etc.
(*) Parts
: The asterisked parts such as the holder plates (2 plates), fastening bolts for holder plates (8 bolts), and fastening bolts for body’s
plate (4 bolts) are built in to constitute component parts of the body’s plate.
: Never remove the above-mentioned component parts under any circumstances since they are absolutely required to ensure saf ety.
Fig. 4 FRONT VIEW
Exhaust hole (❈)
Unit of indicated dimension (mm)
24
Note:
Exhaust hole: This is a hole to exhaust hot air inside the LCD projector . When installing the unit near a wall, etc., keep it aw ay more than 50 cm or so from the face of the exhaust hole.
– 3 –
ADJUSTMENT OF PROJECTION POSITION (Refer to Fig. 5)
Carry out horizontal and vertical adjustments as follows:
1.
(1) To adjust the horizontal position of the screen, loosen rotary setscrews [E] (there are two pieces on both sides) and 4 hexagon
socket bolts (M5 × 10), and rotate the projector horizontally.
(2) To adjust the vertical position of the screen, loosen the assembling bolts (there are 4 pieces on both sides), then tilt the front of the
projector vertically.
Tighten the rotary setscrews [E], hexagon socket bolts (M5 × 10), assembling bolts, and fix the LCD projector.
2.
Fig. 5 ADJUSTMENT
Hexagon wrench (accessory)
Rotary setscrew [E]
Assembling bolt for M8
Assembling bolt (M8 × 25)
Tip of LCD Projector ~ Center of ceiling plate
Lens center
Tilt adjusting latitude of 15 degrees
Unit of indicated dimensions (mm)
148
339
367
FILTER CLEANING (Carry out filter cleaning with appropriate intervals)
Before replacing the filter, ne ver f orget to turn OFF the main power switch and unplug the power cord from the outlet.
Fig. 6 REPLACEMENT
126.2
405
48
453
Remove the 2 filter guard fixing screws,
1.
and remove the filter guard. Push the knob of the filter cover in the
2.
direction indicated by the arrow mark, and raise it.
T ak e out the filter , wash it well in w ater or
3.
synthetic detergent, and dry it completely. Set the filter on the filter cover , and install
4.
the filter cover on the body. Tighten 2 filter guard fixing screws, then
5.
set the filter guard.
2 filter guard fixing screws
Filter guard
– 4 –
Filter cover
VICTOR COMPANY OF JAPAN, LIMITED
Filter
Printed in Japan 0999YMPS/VP
Loading...