SERVICE MANUAL
WIDE LCD PANEL TELEVISION
YA209C20054
BASIC CHASSIS
LT-Z32SX4B,
FL
LT-Z32SX4B
LT-Z32SX4B
LT-Z32SX4S
LT-Z32SX4B
Supplementary
Please be informed that this service manual contains the related matters following the parts replacement in
the LCD PANEL UNIT.
For details other than those described in this manual, please refer to the LT-Z32SX4B, LT-Z32SX4B/A, LTZ32SX4B/S and LT-Z32SX4S/S service manual (No.YA209, 2005/1) LT-Z32SX4B/C service manual
(No.YA209B, 2005/1).
SECTION 1
/A,
/S,
/S,
/C
PRECAUTION
Please refer to "LT-Z32SX4B, LT-Z32SX4B/A, LT-Z32SX4B/S and LT-Z32SX4S/S (No.YA209)" about this section.
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
Please refer to "LT-Z32SX4B, LT-Z32SX4B/A, LT-Z32SX4B/S and LT-Z32SX4S/S (No.YA209)" about this section.
COPYRIGHT © 2005 Victor Company of Japan, Limited
No.YA209C
2005/4
SECTION 3
DISASSEMBLY
CAUTION AT DISASSEMBLY:
• Make sure that the power cord is disconnected from the outlet.
• Pay special attention not to break or damage the parts.
• When removing each board, remove the connectors as required. Taking notes of the connecting points (connector numbers)
makes service procedure manageable.
• During the procedure, place a mirror mat etc. under the LCD UNIT and be careful not to damage the PANEL.
• Make sure that there is no bent or stain on the connectors before inserting, and firmly insert the connectors.
3.1 DISASSEMBLY PROCEDURE
3.1.1 CAUTION ON REMOVING THE LCD PANEL UNIT
The LCD PANEL is fixed to the FRONT PANEL (at the back side)
by using double-side adhesive tapes. To remove the LCD
PANEL UNIT, remove the adhesive tape on the FRONT PANEL
slowly.
LCD PANEL UNIT
Double-side adhesive tapes
Double-side adhesive tapes
FRONT PANEL
3.1.2 REMOVING THE CONTROL PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the LCD PANEL UNIT.
(1) Remove the 4 screws [A], then remove the CONTROL
PWB COVER.
(2) Remove the 2 screws [B], then remove the CONTROL
PWB.
CAUTION:
Carry out the procedure with extra care as the FERRITE
CORE is affixed with double-side adhesive tapes and it may
break if extra force is applied.
3.1.3 REMOVING THE INVERTER PWB (Fig.1)
• Remove the STAND.
• Remove the REAR COVER.
• Remove the LCD PANEL UNIT.
(1) Remove the 6 screws [C], then remove the INVERTER
PWB COVER.
(2) Remove the 3 screws [D], then remove the INVERTER
PWB.
(3) Remove the 8 screws [E], then remove the INVERTER
PWB COVER.
(4) Remove the 3 screws [F], then remove the INVERTER
COLD PWB.
3.1.4 REMOVING THE BACK LIGHT UINT (Fig.1)
CAUTION:
When replacing the BACK LIGHT UINT, be careful to
prevent dust attachment to the UNIT. If dust particles
attached to the UNIT, it becomes the cause of uneven
brightness.
• Remove the STAND.
• Remove the REAR COVER.
• Remove the LCD PANEL UNIT.
• Remove the CONTROL PWB.
• Remove the INVERTER PWB.
• Remove the INVERTER COLD PWB.
(1) Remove the 14 screws [G], then remove the TOP PANEL
FRAME.
(2) Remove the 4 screws [H], then remove the LCD PANEL.
CAUTION:
When removing the LCD PANEL, be careful not to give
stress to the FPC which connects the PWB and the LCD
PANEL.
CAUTION ON EXCHAGING THE BACK LIGHT UINT
• If the screws that are not specified in this section are
removed, the LCD PANEL will be removed and it cannot be
reassembled.
1-2 (No.YA209C)