JVC KS-FX942REE Instructions Manual

CASSETTE RECEIVER

CASSETTEN-RECEIVER
RADIOCASSETTE

ENGLISH

RADIO/CASSETTESPELER

KS-FX942R

SOUND

ATT

U

SOURCE

F

R

D

VOL

VOL

DEUTSCH

FRANÇAIS

KS-FX942R

NEDERLANDS

For installation and connections, refer to the separate manual.
Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch.
Pour l’installation et les raccordements, se référer au manuel séparé.
Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de
desbetreffende handleiding.

INSTRUCTIONS

BEDIENUNGSANLEITUNG

MANUEL D’INSTRUCTIONS

GEBRUIKSAANWIJZING

GET0121-001A

[E/EX]

How to reset your unit

After detaching the control panel, press the reset button on the panel holder using a ball-point pen
or a similar tool.
This will reset the built-in microcomputer.

ENGLISH

Note:

Your preset adjustments—such as preset channels or sound adjustments—will also be erased.

How to use the MODE button

If you press MODE, the unit goes into functions mode (“MODE” flashes on the upper part of the
display). While in functions mode, the number buttons work as different function buttons.

• When connecting a JVC MP3-compatible CD changer: The 5/∞ buttons will also work as
+10/–10 buttons after pressing MODE.

Ex.: When number button 2 works as MO (monaural) button.

MO (monaural)
indicator lights up.

To use these buttons for original functions again after pressing MODE, wait for 5 seconds
without pressing any of these buttons until the functions mode is cleared (“MODE” disappears from
the display).

• Pressing MODE again also clears the functions mode.

Time countdown
indicator

2

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

CONTENTS

How to reset your unit ............................... 2

How to use the MODE button ................... 2

LOCATION OF THE BUTTONS ............ 4

Control panel ............................................. 4

Remote controller ...................................... 5

Preparing the remote controller ................ 6

BASIC OPERATIONS ....................... 7

Turning on the power ................................ 7

Setting the clock ........................................ 8

RADIO OPERATIONS ...................... 9

Listening to the radio ................................. 9

Storing stations in memory ....................... 10

Tuning in to a preset station ...................... 11

RDS OPERATIONS ......................... 12

What you can do with RDS ....................... 12

Other convenient RDS functions and

adjustments ............................................ 16

TAPE OPERATIONS ........................ 19

Listening to a cassette .............................. 19

Finding the beginning of a tune ................. 20

Other convenient tape functions ............... 21

Prohibiting cassette ejection ..................... 22

OTHER MAIN FUNCTIONS ................ 25

Changing the general settings (PSM) ....... 25

Detaching the control panel ...................... 29

CD CHANGER OPERATIONS .............. 30

About MP3 discs ....................................... 30

Playing discs ............................................. 30

Selecting the playback modes .................. 34

EXTERNAL COMPONENT OPERATIONS ... 35

Playing an external component ................. 35

DAB TUNER OPERATIONS ................ 36

Tuning in to an ensemble and one of the

services .................................................. 36

Storing DAB services in memory .............. 37

Tuning in to a preset DAB service ............. 38

What you can do more with DAB .............. 39

TROUBLESHOOTING ...................... 40

MAINTENANCE ............................. 42

SPECIFICATIONS ........................... 43

ENGLISH

SOUND ADJUSTMENTS ................... 23

Selecting preset sound modes

(C-EQ: custom equalizer) ....................... 23

Adjusting the sound .................................. 24

Note:

For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on
the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.

BEFORE USE

*

*

For safety....

• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.

• Stop the car before performing any complicated
operations.

Temperature inside the car....

If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.

3

Control panel

ENGLISH

LOCATION OF THE BUTTONS

Display window

s d

f g h

j

k l

1 2

1 (standby/on/attenuator) button
2 5 (up) button

23 (tape direction) button

3 4 /¢ buttons
4 Remote sensor
5 Display window
6 0 (eject) button
7 FM AM (DAB) button
8 TAPE CD-CH (CD changer) button
9 (control panel release) button
p ∞ (down) button
q SEL (select) button
w Control dial
e EQ (equalizer) button
r MO (monaural) button
t (Dolby B) button
y Number buttons
u RPT (repeat) button
i RND (random) button

• Functions only when connecting to a CD changer.

o MODE button

• Also functions as SSM buttons when pressed
together with DISP (display) button.

; DISP (display) button

• Also functions as SSM buttons when pressed
together with MODE button.

a TP PTY (traffic programme/programme type)

button

3

4

w9 q r a;u i op

z

5

e

4

t

v

y

b

KS-FX942R

ncx/

6 7

8

Display window

s Disc information indicators—

TAG (ID3 Tag), (folder), (track/file)

• Lights up only when playing an MP3 disc or a
CD Text on a JVC MP3-compatible CD changer.

d Tape-in indicator
f Main display
g Playback item indicators—

• (disc): Lights up only when connecting to a
CD changer.

• (folder): Lights up only when playing an MP3
disc on a JVC MP3-compatible CD changer.

h Source/clock display
j RND (random) indicator

• Lights up only when connecting to a CD changer.

k EQ (equalizer) indicator
l Sound mode (C-EQ: custom equalizer)

indicators—ROCK, CLASSIC, POPS,
HIP HOP, JAZZ, USER

/ (Dolby B) indicator
z Tuner reception indicators—MO (monaural),

ST (stereo)

x LOUD (loudness) indicator
c RDS indicator—AF, REG, TP, PTY
v MP3 indicator

• Lights up only when playing an MP3 disc on a
JVC MP3-compatible CD changer.

b Volume (or audio) level indicator

Equalizer pattern indicator

n RPT (repeat) indicator

Remote controller

ATT

U

SOURCE

R

D

VOL

SOUND

F

VOL

3 • Selects the preset stations while listening to

the radio (or the DAB tuner).
Each time you press the button, the preset
station (or service) number increases, and
the selected station (or service) is tuned in.

• While playing an MP3 disc on an MP3­compatible CD changer;
– Skips to the previous disc if pressed

briefly.

– Skips to the previous folder if pressed and

held.

Note:

While playing a CD on a CD changer, this
always skips to the previous disc.

4 Functions the same as the control dial on the

main unit.

Note:

These buttons do not function for the
preferred setting mode adjustment.

5 Selects the sound mode (C-EQ: custom

equalizer).
Each time you press the button, the sound
mode (C-EQ) changes.

ENGLISH

1 • Turns on the unit if pressed when the unit is

turned off.

• Turns off the unit if pressed and held until
“SEE YOU” appears on the display.

• Drops the volume level in a moment if
pressed briefly.
Press again to resume the volume.

2 • Selects the band while listening to the radio

(or the DAB tuner).
Each time you press the button, the band
changes.

• Changes the tape direction while listening to
a cassette.
Each time you press the button, the tape
direction changes alternately.

• While playing an MP3 disc on an MP3­compatible CD changer;
– Skips to the next disc if pressed briefly.
– Skips to the next folder if pressed and

held.

Note:

While playing a CD on a CD changer, this
always skips to the next disc.

6 Selects the source.

Each time you press the button, the source
changes.

7 • Searches for stations while listening to the

radio.

• Selects services while listening to the DAB
tuner if pressed briefly.

• Searches for ensembles while listening to
the DAB tuner if pressed for more than one
second.

• Functions as the fast-forward or rewind
buttons if pressed and held while listening to
a cassette.
To release this operation, press button 2 to
resume playback.

• Functions as Multi Music Scan buttons if
pressed while listening to a cassette.
To release this operation, press button 2 to
resume playback.

• Fast-forwards or reverses the track/file if
pressed and held while listening to the CD
changer.

• Skips to the beginning of the next track/file
or goes back to the beginning of the current
(or previous) tracks/files if pressed briefly
while listening to the CD changer.

5

Preparing the remote controller

Before using the remote controller:

• Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no

ENGLISH

obstacle in between.

Remote sensor

• Do not expose the remote sensor to strong
light (direct sunlight or artificial lighting).

Installing the battery

When the controllable range or effectiveness of
the remote controller decreases, replace the
battery.

1. Remove the battery holder.

1) Push out the battery holder in the direction
indicated by the arrow using a ball-point
pen or a similar tool.

2) Remove the battery holder.

(back side)

3. Return the battery holder.

Insert again the battery holder by pushing it
until you hear a clicking sound.

(back side)

WARNING:

• Store the battery in a place where children
cannot reach.
If a child accidentally swallows the battery,
consult a doctor immediately.

• Do not recharge, short, disassemble, or heat the
battery or dispose of it in a fire.
Doing any of these things may cause the battery
to give off heat, crack, or start a fire.

• Do not leave the battery with other metallic
materials.
Doing this may cause the battery to give off
heat, crack, or start a fire.

• When throwing away or saving the battery,
wrap it in tape and insulate; otherwise, the
battery may start to give off heat, crack, or start
a fire.

• Do not poke the battery with tweezers or similar
tools.
Doing this may cause the battery to give off
heat, crack, or start a fire.

2. Place the battery.

Slide the battery into the holder with the +
side facing upwards so that the battery is
fixed in the holder.

6

Lithium coin
battery (product
number: CR2025)

CAUTION:

DO NOT leave the remote controller in a place
(such as dashboards) exposed to direct sunlight
for a long time. Otherwise, it may be damaged.

KS-FX942R is equipped with the steering
wheel remote control function.
If your car is equipped with the steering wheel
remote controller, you can operate this
receiver using the controller.

• See the Installation/Connection Manual
(separate volume) for connection to utilize
this function.

BASIC OPERATIONS

ENGLISH

31

Turning on the power

1

Turn on the power.

Note on One-Touch Operation:

When you select a source in step 2 below, the
power automatically comes on. You do not have
to press this button to turn on the power.

2

Select the source.

To operate the tuner (FM or AM),

see pages 9 – 18.

To play a tape,

see pages 19 – 22.

To operate the CD changer,

see pages 30 – 34.

To operate the external component

(LINE IN), see page 35.

To operate the DAB tuner,

see pages 36 – 39.

2

3

Adjust the volume.

To increase the volume

To decrease the volume

Volume level appears.

Volume (or audio) level indicator

(see page 27)

4

Adjust the sound as you want. (See
pages 23 and 24.)

To drop the volume in a moment

Press briefly while listening to any
source. “ATT ” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.

• If you turn the control dial, you can also restore
the sound.

To turn off the power

Press and hold for more than one
second.

“SEE YOU” appears, then the unit turns off.

7

ENGLISH

Setting the clock

You can also set the clock system to either
24 hours or 12 hours.

1

Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see page 26.)

2

Set the hour.

1 Select “CLOCK H” (hour) if not shown on

the display.

2 Adjust the hour.

12

4

Set the clock system.

1 Select “24H/12H.”
2 Select “24H” or “12H.”

12

5

Finish the setting.

Note:

To show the clock time on the display, see page 27.

3

Set the minute.

1 Select “CLOCK M” (minute).
2 Adjust the minute.

12

8

To check other information during play, press
DISP (display).

Each time you press the button, the other
information will be shown on the upper part of
the display. (See page 27 for details.)

• Pressing DISP (display) with the unit turned off
will show the clock time for about 5 seconds.

RADIO OPERATIONS

ENGLISH

Listening to the radio

You can use either automatic searching or manual
searching to tune in to a particular station.

Searching a station automatically:
Auto search

1

Select the band (FM1 – 3, AM).

Each time you press the
button, the band changes as
follows:

FM 1

(F1)

Lights up when receiving an FM stereo
broadcast with sufficient signal strength.

* When “CLOCK” is set to “ON” (see page 27),

the current indication will soon change to the
clock time.

FM 2

(F2)

Selected band appears*.

FM 3

(F3)

A M

To stop searching before a station is received,

press the same button you have pressed for
searching.

Searching a station manually:
Manual search

1

Select the band (FM1 – 3, AM).

Each time you press the
button, the band changes as
follows:

FM 1

(F1)

Note:

This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to an
FM broadcast.

2

Press and hold ¢ or 4
until “MANU” (manual) starts
flashing on the display.

FM 2

(F2)

FM 3

(F3)

A M

Note:

This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.

2

Start searching a station.

To search stations of
higher frequencies

To search stations of
lower frequencies

When a station is received, searching stops.

CONTINUED ON THE NEXT PAGE

9

3

Tune in to a station you want while
“MANU” (manual) is flashing.

ENGLISH

To tune in to stations
of higher frequencies

To tune in to stations
of lower frequencies

Storing stations in memory

You can use one of the following two methods to
store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong­station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

• If you release your finger from the button,
the manual mode will automatically turn
off after 5 seconds.

• If you hold down the button, the frequency
keeps changing (in 50 kHz intervals for
FM and 9 kHz intervals for AM—MW/LW)
until you release the button.

When an FM stereo broadcast is hard to
receive:

1 Press MODE to enter the

functions mode while listening
to an FM stereo broadcast.
“MODE” flashes on the upper
part of the display.

2 Press MO (monaural), while

“MODE” is still flashing on the
display, so that the MO
indicator lights up on the
display.
Each time you press the
button, the MO indicator lights
up and goes off alternately.

You can preset 6 local FM stations in each FM
band (FM1, FM2, and FM3).

1

Select the FM band (FM1 – 3) you
want to store FM stations into.

Each time you press the
button, the band changes as
follows:

FM 1

(F1)

2

Press and hold both buttons for

FM 2

(F2)

FM 3

(F3)

A M

more than 2 seconds.

“- -SSM- -” appears, then disappears
when automatic preset is over.

MO (monaural) indicator

When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved.

10

Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2, or FM3).
These stations are preset in the number buttons
—No.1 (lowest frequency) to No.6 (highest
frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.

Manual preset

You can preset up to 6 stations in each band
(FM1, FM2, FM3, and AM) manually.

4

Repeat the above procedure to store
other stations into other preset
numbers.

Ex.: Storing FM station of 92.5 MHz into the

preset number 1 of the FM1 band.

1

Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).

Each time you press the
button, the band changes as
follows:

FM 1

(F1)

2

Tune in to a station (in this example,
of 92.5 MHz).

FM 2

(F2)

FM 3

(F3)

To tune in to stations
of higher frequencies

To tune in to stations
of lower frequencies

A M

Notes:

• A previously preset station is erased when a new
station is stored in the same preset number.

• Preset stations are erased when the power supply to
the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset
the stations again.

Tuning in to a preset station

You can easily tune in to a preset station.
Remember that you must store stations first. If
you have not stored them yet, see “Storing
stations in memory” on pages 10 and 11.

1

Select the band (FM1 – 3, AM).

Each time you press the
button, the band changes as
follows:

FM 1

(F1)

FM 2

(F2)

FM 3

(F3)

A M

ENGLISH

3

Press and hold the number button
(in this example, 1) for more than
2 seconds.

Selected band/preset number
and “MEMO” (memory) appear
alternately for a while.

2

Select the number (1 – 6) for the
preset station you want.

11

RDS OPERATIONS

What you can do with RDS

RDS (Radio Data System) allows FM stations to
send an additional signal along with their regular
programme signals. For example, the stations

ENGLISH

send their station names, as well as information
about what type of programme they broadcast,
such as sports or music, etc.
Another advantage of RDS function is called
“Enhanced Other Networks.” By using the
Enhanced Other Networks data sent from a
station, you can tune in to a different station of a
different network broadcasting your favorite
programme or traffic announcement while
listening to another programme or to another
source such as tape.

By receiving the RDS data, this unit can do the
following:

• Tracing the same programme automatically
(Network-Tracking Reception)

• Standby Reception of TA (Traffic
Announcement) or your favorite programme

• PTY (Programme Type) search

• Programme search

• And some other functions

Tracing the same programme
automatically (Network-Tracking
Reception)

To use Network-Tracking Reception

You can select the different modes of network­tracking reception to continue listening to the
same programme in its finest reception.
When shipped from the factory, “AF” is selected.

• AF: Network-Tracking Reception is
activated with Regionalization set to
“off.”
With this setting, the unit switches to
another station within the same
network when the receiving signals
from the current station become
weak. (In this mode, the programme
may differ from the one currently
received.)
The AF indicator lights up but the
REG indicator does not.

• AF REG: Network-Tracking Reception is
activated with Regionalization set to
“on.”
With this setting, the unit switches to
another station, within the same
network, broadcasting the same
programme when the receiving
signals from the current station
become weak.
Both the AF indicator and the REG
indicator light up.

When driving in an area where FM reception is
not good, the tuner built in this unit automatically
tunes in to another RDS station, broadcasting the
same programme with stronger signals. So, you
can continue to listen to the same programme in
its finest reception, no matter where you drive.
(See the illustration on page 18.)
Two types of the RDS data are used to make
Network-Tracking Reception work correctly
—PI (Programme Identification) and AF
(Alternative Frequency).
Without receiving these data correctly from the
RDS station you are listening to, Network­Tracking Reception will not operate.

12

• OFF: Network-Tracking Reception is
deactivated.
Neither the AF indicator nor the REG
indicator lights up.

AF indicator REG indicator

Note:

If a DAB tuner is connected and Alternative Reception
(for DAB services) is activated, Network-Tracking
Reception (“AF”) is also activated automatically. On
the other hand, Network-Tracking Reception cannot
be deactivated without deactivating Alternative
Reception. (See page 39.)

1

Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see page 26.)

Using TA Standby Reception

TA Standby Reception allows the unit to switch
temporarily to Traffic Announcement (TA) from
the current source (another FM station, tape, or
other connected components).

• TA Standby Reception will not work if you are
listening to an AM station.

ENGLISH

2

Select “AF-REG” (alternative
frequency/regionalization reception)
if not shown on the display.

3

Select the desired mode—“AF,”
“AF REG,” or “OFF.”

4

Finish the setting.

Press TP PTY to activate TA Standby Reception.

7 When the current source is FM, the TP

indicator either lights up or flashes.

• If the TP indicator lights up, TA Standby

Reception is activated.
If a station starts broadcasting a traffic
announcement, “TRAFFIC” appears on the
display, and this unit automatically tunes in to
the station. The volume changes to the
preset TA volume level (see page 17) and the
traffic announcement can be heard.

• If the TP indicator flashes, TA Standby

Reception is not yet activated since the
station being received does not provide the
signals used for TA Standby Reception.
To activate TA Standby Reception, you need
to tune in to another station providing these
signals. Press ¢ or 4 to search
for such a station.
When a station providing these signals is
tuned in, the TP indicator stops flashing and
remains lit. Now TA Standby Reception is
activated.

7 When the current source is other than FM,

the TP indicator lights up.
If a station starts broadcasting a traffic
announcement, “TRAFFIC” appears on the
display, and this unit automatically changes the
source and tunes in to the station.

To deactivate the TA Standby Reception,

press TP PTY again. The TP indicator goes off.

13

Using PTY Standby Reception

PTY Standby Reception allows the unit to switch
temporarily to your favorite programme (PTY:
Programme Type) from the current source

ENGLISH

(another FM station, tape, or other connected
components).

4

Finish the setting.

• PTY Standby Reception will not work if you are
listening to an AM station.

You can select your favorite programme type for
PTY Standby Reception.
When shipped from the factory, PTY Standby
Reception is turned off. (“OFF” is selected for
PTY Standby Reception.)

1

Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see page 26.)

2

Select “PTY STBY” (standby) if not
shown on the display.

7 When the current source is FM, the PTY

indicator either lights up or flashes.

• If the PTY indicator lights up, PTY Standby
Reception is activated.
If a station starts broadcasting the selected
PTY programme, this unit automatically
tunes in to the station.

• If the PTY indicator flashes, PTY Standby
Reception is not yet activated since the
station being received does not provide the
signals used for PTY Standby Reception.
To activate PTY Standby Reception, you
need to tune in to another station providing
these signals. Press ¢ or 4 to
search for such a station.
When a station providing these signals is
tuned in, the PTY indicator stops flashing
and remains lit. Now PTY Standby Reception
is activated.

7 When the current source is other than FM,

the PTY indicator lights up.
If a station starts broadcasting the selected
PTY programme, this unit automatically
changes the source and tunes in to the station.

3

Select one of the twenty-nine PTY
codes. (See page 18.)

Selected code name
appears on the display
and is stored into
memory.

14

To deactivate the PTY Standby Reception,

select “OFF” in step 3 on the left column. The
PTY indicator goes off.

Searching your favorite programme

You can search any one of the PTY codes.
In addition, you can store your 6 favorite
programme types in the number buttons.
When shipped from the factory, the following
6 programme types have been stored in the
number buttons (1 to 6).

To store your favorite programme types, see
below.
To search your favorite programme type, see
page 16.

1

POP M

45

CLASSICS

2

ROCK M EASY M

AFFAIRS

3

6

VARIED

2

Select one of the twenty-nine PTY
codes. (See page 18.)

Selected code name
appears on the display.

3

Press and hold the number button
for more than 2 seconds to store the
PTY code selected into the preset
number you want.

ENGLISH

To store your favorite programme types

1

Press and hold TP PTY for more
than 2 seconds while listening to an
FM station.

The last selected PTY code appears.

Selected preset number and “MEMO”
(memory) appear alternately.

4

Press and hold TP PTY for more
than 2 seconds to exit from this
mode.

15

To search your favorite programme type

1

Press and hold TP PTY for more
than 2 seconds while listening to an

ENGLISH

FM station.

The last selected PTY code appears.

2

To select one of your favorite
programme type

or

To select any one of the twenty-nine
PTY codes

• If there is a station broadcasting a programme
of the same PTY code as you selected, that
station is tuned in.

• If there is no station broadcasting a
programme of the same PTY code as you
selected, the station will not change.

Note:

In some areas, the PTY search will not work correctly.

Other convenient RDS
functions and adjustments

Automatic selection of the station
when using the number buttons

Usually when you press the number button, the
preset station is tuned in.
However, when the preset station is an RDS
station, something different will happen. If the
signals from that preset station are not sufficient
for good reception, this unit, using the AF data,
tunes in to another frequency broadcasting the
same programme as the original preset station is
broadcasting. (Programme search)

• The unit takes some time to tune in to another
station using programme search.

Preset number appears only if you select
a PTY code using the number buttons.

Ex.: When “ROCK M” is selected

3

Press ¢ or 4 to start PTY
search for your favorite programme.

To activate programme search, follow the

procedure below.

• See also “Changing the general settings
(PSM)” on page 25.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items
appears on the display.

2 Press ¢ or 4 to select

“P(Programme)-SEARCH.”

3 Turn the control dial clockwise to select “ON.”

Now programme search is activated.

4 Press SEL (select) to finish the setting.

To cancel programme search, repeat the same

procedure and select “OFF” in step 3 by turning
the control dial counterclockwise.

16

Changing the display mode while
listening to an FM station

You can change the initial indication on the
display to station name (PS NAME) or station
frequency (FREQ) while listening to an FM RDS
station.

• See also “Changing the general settings
(PSM)” on page 25.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items
appears on the display.

2 Press ¢ or 4 to select “TU DISP”

(tuner display).

3 Turn the control dial to set to the desired

indication (“PS NAME” or “FREQ”).

4 Press SEL (select) to finish the setting.

Note:

By pressing DISP (display), you can change the
display while listening to an FM RDS station. Each
time you press the button, the following information
appears on the main display:

Station name

(PS NAME)

Station frequency

(FREQ)

Programme type

(PTY)

• Then, the display goes back to the original
indication in several seconds.

• For more details, see “To set the clock display—
CLOCK” on page 27.

Setting the TA volume level

You can preset the volume level for TA Standby
Reception. When a traffic programme is received,
the volume level automatically changes to the
preset level.

• See also “Changing the general settings
(PSM)” on page 25.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items
appears on the display.

2 Press ¢ or 4 to select “TA VOL”

(TA volume).

3 Turn the control dial to set to the desired

volume.
You can set it from “VOL 00” to “VOL 50.”

4 Press SEL (select) to finish the setting.

Automatic clock adjustment

When shipped from the factory, the clock built in
this unit is set to be readjusted automatically
using the CT (Clock Time) data in the RDS
signal.
If you do not want to use automatic clock
adjustment, follow the procedure below.

• See also “Changing the general settings
(PSM)” on page 25.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items
appears on the display.

2 Press ¢ or 4 to select “AUTO

ADJ” (adjustment).

3 Turn the control dial counterclockwise to select

“OFF.”
Now automatic clock adjustment is canceled.

4 Press SEL (select) to finish the setting.

To reactivate clock adjustment, repeat the

same procedure and select “ON” in step 3 by
turning the control dial clockwise.

ENGLISH

Note:

You must stay tuned to the same station for more than
2 minutes after setting “AUTO ADJ” to “ON.”
Otherwise, the clock time will not be adjusted. (This is
because the unit takes up to 2 minutes to capture the
CT data in the RDS signal.)

17

PTY codes

NEWS: News
AFFAIRS: Topical programmes expanding

ENGLISH

INFO: Programmes which impart

SPORT: Sport events
EDUCATE: Educational programmes
DRAMA: Radio plays
CULTURE: Programmes on national or

SCIENCE: Programmes on natural science

VARIED: Other programmes like comedies

POP M: Pop music
ROCK M: Rock music
EASY M: Easy-listening music
LIGHT M: Light music
CLASSICS: Classical music
OTHER M: Other music
WEATHER: Weather information
FINANCE: Reports on commerce, trading,

CHILDREN: Entertainment programmes for

on current news or affairs

advice on a wide variety of topics

regional culture

and technology

or ceremonies

the Stock Market, etc.

children

SOCIAL: Programmes on social

activities

RELIGION: Programmes dealing with any

aspect of belief or faith, or the
nature of existence or ethics

PHONE IN: Programmes where people can

express their views either by
phone or in a public forum

TRAVEL: Programmes about travel

destinations, package tours,
and travel ideas and
opportunities

LEISURE: Programmes concerned with

recreational activities such as
gardening, cooking, fishing,

etc.
JAZZ: Jazz music
COUNTRY: Country music
NATION M: Current popular music from

another nation or region, in that

country’s language
OLDIES: Classic pop music
FOLK M: Folk music
DOCUMENT: Programmes dealing with

factual matters, presented in an

investigative style

18

The same programme can be received on different frequencies.

Programme 1
broadcasting on
frequency A

Programme 1
broadcasting on
frequency B

Programme 1
broadcasting on
frequency C

Programme 1
broadcasting on
frequency E

Programme 1
broadcasting on
frequency D

TAPE OPERATIONS

ENGLISH

Listening to a cassette

You can play back type I (normal) tapes.

1

Open the control panel.

Note on One-Touch Operation:

When a cassette is already in the cassette
compartment, pressing TAPE CD-CH turns on
the unit and starts tape play automatically.

2

Insert a cassette into the cassette
compartment.

The unit turns on and
tape play starts
automatically.

To stop play and eject the cassette

Press 0.
Tape play stops, the control panel flips down. The
cassette automatically ejects from the cassette
compartment. The source changes to the
previously selected one.
If you change the source, tape play also stops
(without ejecting the cassette this time).

• You can also eject the cassette by pressing 0

while the unit is turned off.

To fast-forward and rewind a tape

Press and hold ¢ for
more than one second to
fast-forward the tape.
When the tape reaches its
end, the tape is reversed
and playback starts from
the beginning of the other
side.

3

Close the control panel by hand.

4

Select the tape direction.

Each time you press 23,
the tape direction changes
alternately between forward
( ) and reverse
( ).

Press and hold 4 for more than one
second to rewind the tape.
When the tape reaches its end, playback of the
same side starts.

To stop fast-forward and rewind at any
position on the tape, press 23.

Tape play starts from that position on the tape.

Notes:

• When one side of the tape reaches its end during
play, the other side of the tape automatically starts
playing. (Auto Reverse)

• When the tape reaches its end while fast­forwarding, the tape direction will be changed
automatically.

19

To play back tapes recorded with the
Dolby B NR*

1 Press MODE to enter the functions mode

ENGLISH

while listening to a tape.
“MODE” flashes on the upper part of the
display.

Ex.: When you locate three tunes ahead

of the current tune

2 Press (Dolby B), while “MODE” is still

flashing on the display so that the
(Dolby B) indicator lights up.

“DOLBY B” also appears on the display for

several seconds.

To cancel the Dolby B NR, repeat steps 1
and 2 again so that the (Dolby B) indicator
goes off.

* Manufactured under license from Dolby

Laboratories.
“Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.

Finding the beginning of a
tune

Multi Music Scan (MMS) allows you to
automatically start playback from the beginning
of a specified tune. You can specify up to 9 tunes
ahead of or before the current tune.

Each time you press the buttons, the number
changes up to ±9.
When the beginning of the specified tune is
located, playback starts automatically.

Notes:

• While locating a specified tune:
– If the tape is rewound to its beginning, playback

starts from the beginning of that side.

– If the tape is fast-forwarded to the end, it is

reversed and played from the beginning of the
other side.

• In the following cases, the Multi Music Scan

function may not operate correctly:

– Tapes with tunes having long pianissimo

passages (very quiet parts) or non-recorded

portions between tunes.
– Tapes with short non-recorded sections.
– Tapes with high level of noise or humming

between tunes.
– Tapes with tunes recorded at low recording

levels.
– The Dolby NR setting does not match. For

example, if Dolby B NR is on and the tape was

recorded with no Dolby NR.

During playback

Specify the tune you want to locate (how
many tunes ahead of or before the
current tune).

Press ¢ to locate a
tune ahead of the current
tune on the cassette.

Press 4 to locate a
tune before the current
tune on the cassette.

20

Other convenient tape functions

Skipping the blank portions on the tape

You can skip blank portions between the tunes
(Blank Skip).
When this function is turned on, the unit fast­forwards (skipping blank portions of 15 seconds
or more), to the next tune and starts playback.

• See also “Changing the general settings
(PSM)” on page 25.

1

Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see page 26.)

2

Press ¢ or 4 to select
“B.SKIP” (blank skip).

3

Turn the control dial clockwise to
select “ON.”

Now Blank Skip is
activated.

4

Finish the setting.

To cancel Blank Skip, repeat the same procedure

and select “OFF” in step 3 by turning the control
dial counterclockwise.

ENGLISH

21

Playing the current tune repeatedly

You can play the current tune repeatedly
(Repeat Play).

ENGLISH

Lights up when Repeat Play is turned on.

When the tune has been played, the tape is
automatically rewound to the beginning of that
tune and the same tune will be played again.

To cancel Repeat Play, repeat steps 1 and 2
again so that the RPT indicator goes off.

1 Press MODE to enter the

functions mode while playing a
tune you want to hear over again
on a cassette.
“MODE” flashes on the upper
part of the display.

2 Press RPT (repeat), while

“MODE” is still on the display, so
that “REPEAT” appears on the
display.

Prohibiting cassette ejection

You can prohibit cassette ejection and lock a
cassette in the cassette compartment.

While pressing TAPE CD-CH, press and
hold for more than 2 seconds.

“NO EJECT” flashes on the display for about
5 seconds, and the cassette is locked and
cannot be ejected.

To cancel the prohibition and unlock the
cassette

While pressing TAPE CD-CH, press and hold

again for more than 2 seconds.
“EJECT OK” flashes on the display for about
5 seconds, and the cassette is unlocked.

Note:

In the following cases, Blank Skip and Repeat Play
may not operate correctly:
– Tapes with tunes having long pianissimo passages

(very quiet parts) or non-recorded portions during

tunes.
– Tapes with short non-recorded sections.
– Tapes with high level noise or humming between

tunes.
– Tapes with tunes recorded at low recording levels.
– The Dolby NR setting does not match. For example,

if Dolby B NR is on and the tape was recorded with

no Dolby NR.

22

Note:

If you press 0 while cassette ejection is prohibited,
the control panel flips down, but the cassette
continues to play and cannot be ejected.

SOUND ADJUSTMENTS

Selecting preset sound modes
(C-EQ: custom equalizer)

You can select a preset sound mode (C-EQ:
custom equalizer) suitable to the music genre.

• There is a time limit in doing the following
procedure. If the setting is canceled before you
finish, start from step 1 again.

1

Press MODE to enter the functions
mode.

“MODE” flashes on the upper
part of the display.

2

Press EQ (equalizer), while “MODE”
is still flashing on the display.

The last selected sound
mode is recalled and applied
to the current source.

Indication For: Preset values

BAS TRE LOUD

USER (Flat sound) 00 00 OFF

ROCK Rock or +03 +01 ON

disco music

CLASSIC Classical +01 –02 OFF

music

POPS Light music +04 +01 OFF

HIP HOP Funk or rap +02 00 ON

music

JAZZ Jazz music +02 +03 OFF

Note:

You can adjust each sound mode to your preference.
Once you make an adjustment, it is automatically
stored for the currently selected sound mode. See
“Adjusting the sound” on page 24.

ENGLISH

Sound mode indicator flashes.

Ex.: If you have selected “USER” previously

3

Select the sound mode you want.

Each time you press the
button, the sound modes
change as follows:

USER

Sound mode indicator flashes.

Ex.: When you select “ROCK”

ROCK

CLASSIC

POPSHIP HOPJAZZ

23

Adjusting the sound

2

Adjust the setting.

You can adjust the sound characteristics to your
preference.

ENGLISH

1

Select the item you want to adjust.

Each time you press the
button, the adjustable items
change as follows:

BAS

(bass)

VOL

(volume)

Indication To do: Range

1

BAS*

TRE*

FAD*

1

2

Adjust the bass. –06 (min.)

Adjust the treble. –06 (min.)

Adjust the front R06 (Rear only)
and rear speaker |
balance. F06 (Front only)

TRE

(treble)

LOUD

(loudness)

(fader)

(balance)

|
+06 (max.)

|
+06 (max.)

FAD

BAL

To increase the level or
turn on the loudness

To decrease the level or
turn off the loudness

Equalization pattern changes
as you adjust the bass or treble.

Ex. 1: When you adjust “TRE” (treble)

Ex. 2: When you turn on the loudness

3

Repeat steps 1 and 2 to adjust the
other items.

BAL Adjust the left L06 (Left only)

and right speaker |
balance. R06 (Right only)

LOUD*

VOL*

*1When you adjust the bass, treble, or loudness, the

*2If you are using a two-speaker system, set the fader

*3Normally the control dial works as the volume

1

Boost low and high
frequencies to LOUD ON
produce a well- |
balanced sound LOUD OFF
at low volume level.

3

adjustment you have made is stored for the
currently selected sound mode (C-EQ) including
“USER.”

level to “00.”

control. So you do not have to select “VOL” to
adjust the volume level.

Adjust the volume. 00 (min.)

|
50 (max.)

To reset each sound mode to the factory
settings, repeat the same procedure and

reassign the preset values listed in the table on
page 23.

24

OTHER MAIN FUNCTIONS

Changing the general settings
(PSM)

You can change the items listed on the next page
by using the PSM (Preferred Setting Mode)
control.

Basic Procedure

1

Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(See page 26.)

2

Select the PSM item you want to
adjust.

3

Adjust the PSM item selected.

Ex.: When you select “AUDIO 2”

4

Repeat steps 2 and 3 to adjust the
other PSM items if necessary.

5

Finish the setting.

ENGLISH

Ex.: When you select “LEVEL”

25

Preferred Setting Mode (PSM) items

• For detailed operations of each PSM items, refer to the pages listed in the table.

Indications Selectable values/items

ENGLISH

CLOCK H Hour adjustment

CLOCK M Minute adjustment

24H/12H 24/12-hour time display

AUTO ADJ Automatic clock setting

CLOCK Clock display

TU DISP Tuner display

AF-REG Alternative frequency/

Regionalization reception

PTY STBY PTY standby

TA VO L Traffic announcement

volume

P-SEARCH Programme search

00 – 59

12H 24H

OFF ON

PS NAME

FREQ

AF AF REG

1

OFF*

OFF

29 programme types

(see page 18)

VOL 00 – VOL 50 VOL 20

OFF ON

Factory-preset See

settings page

0 (0:00) 80 – 23 (1– 12)

00 (0:00) 8

24H

ON

ONONOFF

PS NAME

AF

OFF

8

17

27

17

12, 13

14

17

OFF

16

DAB AF*

2

Alternative frequency
search

DAB VOL*2DAB volume adjustment

LEVEL Level display

DIMMER Dimmer mode

TEL Telephone muting

BEEP Key-touch tone

SCROLL Scroll mode

B.SKIP Blank skip

EXT IN*

3

External component

TAG DISP Tag display

AF OFF AF ON

VOL –12 VOL 12

AUDIO 1 AUDIO 2

AF ON

VOL 00

AUDIO 2

39

39

27

OFF

AUTO OFF

AUTO 27

ON

OFF MUTING 1

MUTING 2

OFF

27

OFF ON ON 28

ONCE AUTO

OFF

ONCE 28

OFF ON OFF 21

CHANGER LINE IN CHANGER 28

TAG OFF TAG ON TAG ON 28

*1Displayed only when the “DAB AF” is set to “AF OFF.”
*2Displayed only when the DAB tuner is connected.
*3Displayed only when one of the following sources is selected—FM, AM, and TAPE.

26

To set the clock display—CLOCK

To select the level meter—LEVEL

You can set the clock to be shown on the display
when the unit is turned on.
When shipped from the factory, the clock is set to
be shown on the display.

• ON: Clock display is turned on.

• OFF: Clock display is turned off. When

“OFF” is selected, the other
information (see table below)
appears instead of the clock
display (except when “LINE IN” is
selected as the source).

When CLOCK is set to OFF:

Source Initial Pressing DISP

indication (display)

Tuner Band
(FM/AM/
DAB)

TAPE “TAPE” or
or disc number
CD-CH

When CLOCK is set to ON:

Clock appears for about
5 seconds.

You can select the level meter display according
to your preference.
When shipped from the factory, “AUDIO 2” is
selected.

• AUDIO 1: Shows the audio level indicator.

• AUDIO 2: Alternates “AUDIO 1” setting and
illumination display.

• OFF: Erases the audio level indicator.

To select the dimmer mode—DIMMER

When you turn on the car headlights, the display
automatically dims (Auto Dimmer).
When shipped from the factory, Auto Dimmer
mode is activated.

• AUTO: Activates Auto Dimmer.

• OFF: Cancels Auto Dimmer.

• ON: Always dims the display.

Note:

Auto Dimmer equipped with this unit may not work
correctly on some vehicles, particularly on those
having a control dial for dimming.
In this case, set the dimmer mode to “ON” or “OFF.”

ENGLISH

Source Initial Pressing DISP

indication (display)

Tuner Clock Band appears for about
(FM/AM/ 5 seconds.
DAB)

TAPE Clock “TAPE” appears for

about 5 seconds.

CD-CH Clock Disc number and track/

file number appear
alternately each time
you press the button.

To select the telephone muting—TEL

This mode is used when a cellular phone system
is connected. Depending on the phone system
used, select either “MUTING 1” or “MUTING 2,”
whichever mutes the sounds from this unit.
When shipped from the factory, this mode is
deactivated.

• MUTING 1: Selects this if this setting can mute
the sounds while using the cellular
phone.

• MUTING 2: Selects this if this setting can mute
the sounds while using the cellular
phone.

• OFF: Cancels the telephone muting.

27

To turn on/off the key-touch tone—BEEP

You can deactivate the key-touch tone if you do
not want it to beep each time you press a button.
When shipped from the factory, the key-touch
tone is activated.

ENGLISH

To turn the tag display on or off
—TAG DISP

This function takes effect only when JVC
MP3-compatible CD changer is connected.

• ON: Activates the key-touch tone.

• OFF: Deactivates the key-touch tone.

To select the scroll mode—SCROLL

You can select the scroll mode for the disc
information (when the entire text cannot be
shown at once).
When shipped from the factory, scroll mode is set
to “ONCE.”

• ONCE: Scrolls only once.

• AUTO: Repeats the scroll (5-second
intervals in between).

• OFF: Cancels scroll mode.

Note:

Even if the scroll mode is set to “OFF,” you can scroll
the display by pressing DISP (display) for more than
one second.

To select the external component to use
—EXT IN

You can connect the external component to the
CD changer jack on the rear using the Line Input
Adapter KS-U57 (not supplied).
To use the external component as the playback
source through this unit, you need to select
which component—CD changer or external
component—to use.
When shipped from the factory, CD changer is
selected as the external component.

An MP3 file can contain file information called
“ID3 Tag” where its album name, performer, track
title, etc. are recorded.
There are two versions—ID3v1 (ID3 Tag version

1) and ID3v2 (ID3 Tag version 2). Only ID3v1 can
be shown.
When shipped from the factory, “TAG ON” is
selected.

• TAG ON: Turns on the ID3 tag display while
playing MP3 files.

• If an MP3 file does not have ID3

tags, folder name and file name
appear.

Note:

If you change the setting from
“TAG OFF” to “TAG ON” while
playing an MP3 file, the tag display
will be activated when the next file
starts playing.

• TAG OFF: Turns off the ID3 tag display while
playing MP3 files. (Only the folder
name and file name can be
shown.)

• CHANGER: To use the CD changer.

• LINE IN: To use the external component
other than CD changer.

Note:

For connecting the Line Input Adapter KS-U57 and
the external component, refer to the Installation/
Connection Manual (separate volume).

28

Detaching the control panel

You can detach the control panel when leaving
the car.
When detaching or attaching the control panel,
be careful not to damage the connectors on the
back of the control panel and on the panel
holder.

Detaching the control panel

Before detaching the control panel, be sure to
turn off the power.

1

Unlock the control panel.

Attaching the control panel

1

Insert the right side of the control
panel into the groove on the panel
holder.

2

Press the left side of the control
panel to fix it to the panel holder.

ENGLISH

2

Pull the control panel out of the unit.

3

Put the detached control panel into
the provided case.

Note on cleaning the connectors:

If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened
with alcohol, being careful not to damage the
connectors.

Connectors

29

ENGLISH

CD CHANGER OPERATIONS

We recommend that you use the JVC MP3­compatible CD changer with your unit.

By using this CD changer, you can play back
your original CD-Rs (Recordable) and CD-RWs
(Rewritable) recorded either in audio CD format
or in MP3 format.

• You can also connect other CH-X series

CD changers (except CH-X99 and CH-X100).
However, they are not compatible with MP3
discs, so you cannot play back MP3 discs.

• You cannot use the KD-MK series CD

changers with this unit.

Before operating your CD changer:

• Refer also to the Instructions supplied with
your CD changer.

• If no discs are in the magazine of the CD
changer or the discs are inserted upside
down, “NO DISC” will appear on the display.
If this happens, remove the magazine and
set the discs correctly.

• If no magazine is loaded in the CD changer,
“NO MAG” appears on the display. If this
happens, insert the magazine in the CD
changer.

• If “RESET 1” – “RESET 8” appears on the
display, something is wrong with the
connection between this unit and the CD
changer. If this happens, check the
connection and make sure the cords are
connected firmly. Then, press the reset
button of the CD changer.

About MP3 discs

MP3 “files (tracks)” can be recorded in
“folders”—in PC terminology.
During recording, the files and folders can be
arranged in a way similar to arranging files and
folders of computer data.
“Root” is similar to the root of a tree. Every file
and folder can be linked to and be accessed from
the root.

Hierarchy

Level 1 Level 2 Level 3 Level 4 Level 5

6

7

8

9

ROOT

01

1

01

05

1

2

: Folders and their playback order

: MP3 files and their playback order

02 03

3

10

11

12

04

4

5

Playing discs

Select the CD changer (CD).

30

1

TAPE

*1If you have changed the “EXT IN” setting to

“LINE IN” (see page 28), you cannot select the CD
changer.

CD*

• When the current disc is an MP3 disc:

Playback starts from the first folder of the
current disc once file check is completed.

Selected disc number*

Folder or album name*

3

Notes:

• When you press TAPE CD-CH, the power
automatically comes on. You do not have to press

2

to turn on the power.

• If you change the source, CD changer play also
stops. Next time you select the CD changer as the

ENGLISH

source, CD changer play starts from where
playback has been stopped previously.

• When you start playing back a CD Text or an MP3
disc, disc information will automatically appear on
the display. (See the explanation that follows.)

To change the display information

While playing back an MP3 file or CD Text, you
can change the disc information shown on the
display.

Each time you press DISP
(display), the display changes to
show the following:

For MP3 discs

MP3 indicator (folder) indicator

*2When “CLOCK” is set to “ON” (see page 27),

the current indication will soon change to the
clock time.

*3If some MP3 files are recorded without being

included in a folder, they are played back first
and “ROOT” appears as the folder name.

• When the current disc is a CD:

Playback starts from the first track of the
current disc.

Selected disc number*

Current track

Elapsed playing time

number

• When “TAG DISP” is set to “TAG ON” (initial
setting: see page 28)

Album name / performer

(folder name* )

5

(TAG lights up on the display)

Track title (file name* )

(TAG lights up on the display)

4

Elapsed playing time and

Current file number

*5If an MP3 file does not have ID3 tags, folder name

and file name appear. In this case, the TAG
indicator will not light up on the display.

5

*4When “CLOCK” is set to “ON” (see page 27),

the current indication will soon change to the
clock time.

CONTINUED ON THE NEXT PAGE

31

• When “TAG DISP” is set to “TAG OFF”

Folder name

( lights up on the display)

ENGLISH

File name

( lights up on the display)

To go to a particular disc directly

Press the number button corresponding to the
disc number to start its playback (while the CD
changer is playing).

Elapsed playing time and

Current file number

For CD Text discs

Each time you press the button,
the display changes as follows:

Disc title / performer

Track title

( lights up on the display)

Elapsed playing time and

Current track number

Notes:

• The display shows up to 8 characters at one
time and scrolls if there are more than 8
characters.
See also “To select the scroll mode—SCROLL”
on page 28.
Some characters or symbols will not be shown
(and be blanked) on the display.
(Ex. “ABCå!d#” ]“ABCA D ”)

• When you press DISP (display) while playing
an audio CD, “NO NAME” appears for the
disc title/performer and the track title.

• To select a disc number from 1 – 6:
Press 1 (7) – 6 (12) briefly.

• To select a disc number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than
one second.

To fast-forward or reverse the track/file

Press and hold ¢ ,
during play, to fast-forward
the track/file.

Press and hold 4 ,
during play, to reverse the
track/file.

Note:

During this operation on an MP3 disc, you can only
hear intermittent sounds. (The elapsed playing time
also changes intermittently on the display.)

To go to the next or previous tracks/files

Press ¢ briefly
during play, to skip ahead
to the beginning of the
next track/file.
Each time you press the
button consecutively, the
beginning of the next
tracks/files is located and
played back.

32

Press 4 briefly during play, to skip back to
the beginning of the current track/file.
Each time you press the button consecutively,
the beginning of the previous tracks/files is
located and played back.

This operation is only possible when
using JVC MP3-compatible CD changer
(CH-X1500).

How to go to the desired track/file quickly

• Ex. 1: To select track/file number 32 while
playing track/file number 6

To go to a track/file quickly

1 Press MODE to enter the functions mode while

playing a disc.

“MODE” flashes on the upper
part of the display.

2 Press 5 (up) or ∞ (down) while still in the

functions mode.

To skip 10 tracks/files*
forwards to the last track/file

To skip 10 tracks/files*
backwards to the first track/file

* The first time you press 5 (up) or ∞ (down)

button, the track/file skips to the nearest
higher or lower track/file with a track/file

number of multiple ten (ex. 10th, 20th, 30th).
Then each time you press the button, you can
skip 10 tracks/files (see “How to go to the
desired track/file quickly” on the right column).

• After the last track/file, the first track/file will

be selected, and vice versa.

(Three times) (Twice)

Track/file 6 \ 10 \ 20 \ 30 \ 31 \ 32

• Ex. 2 :To select track/file number 8 while
playing track/file number 36

(Three times)

Track/file 36 \ 30 \ 20 \ 10 \ 9 \ 8

(Twice)

To skip to the next or previous folder
(only for MP3 discs)

Press 5 (up) while playing an
MP3 disc, to go to the next
folder.
Each time you press the button
consecutively, the next folder is
located, and the first file in the
folder starts playback.

ENGLISH

Note:

If the current playing disc is an MP3 disc, files are
skipped within the same folder.

Press ∞ (down) while playing an MP3 disc, to go
to the previous folder.
Each time you press the button consecutively,
the previous folder is located, and the first file in
the folder starts playback.

33

Selecting the playback modes

To play back tracks/files at random
(Folder Random/Disc Random/Magazine

ENGLISH

Random Play)

1 Press MODE to enter the functions

mode during play.
“MODE” flashes on the upper part
of the display.

2 Press RND (random), while

“MODE” is still flashing on the
display.
Each time you press the button, the
random play mode changes as
follows:

For MP3 discs:

DISC RNDFLDR RND

Canceled

For CDs:

MAG RND

To play back tracks/files repeatedly
(Track Repeat/Folder Repeat/Disc Repeat
Play)

1 Press MODE to enter the functions

mode during play.
“MODE” flashes on the upper part
of the display.

2 Press RPT (repeat), while “MODE”

is still flashing on the display.
Each time you press the button, the
repeat play mode changes as
follows:

For MP3 discs:

TRK RPT

Canceled

For CDs:

Canceled

FLDR RPT

DISC RPT

DISC RPTTRK RPT

MAG RNDDISC RND

Canceled

RND indicator

Ex.: When you select “MAG RND”

Note:

The MP3 indicator also lights up if the current playing
disc is an MP3 disc.

Mode

FLDR RND* and RND All files of the

DISC RND and RND All tracks/files of

MAG RND RND indicator All tracks/files of

Active

indicator

indicators current folder, then
light up. files of the next

indicators the current (or
light up. specified) disc.

lights up. the inserted discs.

Plays at random

folder and so on.

(disc) and RPT indicators

Ex.: When you select “DISC RPT”

Note:

The MP3 indicator also lights up if the current playing
disc is an MP3 disc.

Mode

TRK RPT RPT indicator The current (or

FLDR RPT* and RPT All files of the

DISC RPT and RPT All tracks/files of

* “FLDR RPT” is only applicable for MP3 discs.

Active

indicator

lights up. specified) track/

indicators current (or
light up. specified) folder of

indicators light the current (or
up. specified) disc.

Plays repeatedly

file.

the current disc.

* “FLDR RND” is only applicable for MP3 discs.

34

EXTERNAL COMPONENT OPERATIONS

ENGLISH

Playing an external component

You can connect the external component to the
CD changer jack on the rear using the Line Input
Adapter KS-U57 (not supplied).

Preparations:

• For connecting the Line Input Adapter KS-U57 and
the external component, refer to the Installation/
Connection Manual (separate volume).

• Before operating the external component using the
following procedure, select the external input
correctly. See “To select the external component to
use—EXT IN” on page 28.

1

Select the external component
(LINE IN).

TAPE LINE IN*

2

Turn on the connected component
and start playing the source.

3

Adjust the volume.

4

Adjust the sound characteristics as
you want. (See pages 23 and 24.)

• If “LINE IN”* does not appear on the display,
see page 28 and select the external input
(“LINE IN”).

* Displayed only when one of the following sources is

selected—FM, AM, and TAPE.

Note on One-Touch Operation:

When you press TAPE CD-CH, the power
automatically comes on. You do not have to press

to turn on the power.

35

ENGLISH

DAB TUNER OPERATIONS

We recommend that you use DAB (Digital Audio
Broadcasting) tuner KT-DB1500 or KT-DB1000
with your unit.
If you have another DAB tuner, consult your JVC
IN-CAR ENTERTAINMENT dealer.

• Refer also to the Instructions supplied with
your DAB tuner.

What is DAB system?

DAB is one of the digital radio broadcasting
systems available today. It can deliver CD
quality sound without any annoying
interference and signal distortion.
Furthermore, it can carry text, pictures, and
data.
In contrast to FM broadcast, where each
programme is transmitted on its own
frequency, DAB combines several
programmes (called “services”) to form one
“ensemble.”
In addition, each “service”—called “primary
service”—can also be divided into its
components (called “secondary service”).

With the DAB tuner connected with this unit,
you can enjoy these DAB services.

Tuning in to an ensemble and
one of the services

A typical ensemble has 6 or more programmes
(services) broadcast at the same time. After
tuning in to an ensemble, you can select a
service you want to listen to.

Before you start....

Press FM AM (DAB) briefly if tape, CD changer,
or external component is the current source.

1

Select the DAB tuner.

Each time you press and
hold the button, the DAB
tuner and the FM/AM tuner
are alternately selected.

FM/AMDAB

2

Select the DAB band (DAB1, DAB2,
or DAB3).

Each time you press the
button, the DAB band
changes as follows:

Note:

When reception switches between DAB and FM, the
listening volume level may increase or decrease
inconveniently. This change in the volume level results
from unequal audio injection levels at broadcaster
site, but not from the malfunction of this unit.
To prevent this inconvenience, you can adjust the DAB
volume level. (See “To adjust the DAB volume level”
on page 39.)

36

DAB1

(D1)

Note:

This receiver has three DAB bands (DAB1,
DAB2, DAB3). You can use any of them to tune
in to an ensemble.

DAB2

(D2)

DAB3

(D3)

3

Start searching for an ensemble.

To search for ensembles
of higher frequency

To search for ensembles
of lower frequency

When an ensemble is received, searching
stops.

To stop searching before an ensemble is
received, press the same button you have

pressed for searching.

4

Select a service (either primary or
secondary) you want to listen to.

To select the next
service (If a primary
service has some
secondary services,
they are selected before
the next primary service
is selected.)

To select the previous service (either
primary or secondary)

To change the display information while
tuning in to an ensemble

Normally service name is shown on the display.
If you want to check the ensemble name or its
frequency, press DISP (display).

Each time you press the
button, the following
information appears for a
while in the main display.

To tune in to a particular ensemble
without searching

Before you start....

Press FM AM (DAB) briefly if tape, CD changer,
or external component is the current source.

1 Press and hold FM AM (DAB) to select DAB

tuner as the source.

2 Press FM AM (DAB) repeatedly to select the

DAB band (DAB1, DAB2, or DAB3).

3 Press and hold ¢ or 4 for more

than one second. “MANU” (manual) appears
on the display.

4 Press ¢ or 4 repeatedly until the

ensemble you want is reached.

• If you hold down the button, the frequency
keeps changing until you release the button.

5 Press 5 (up) or ∞ (down) to select a service

(either primary or secondary) you want to
listen to.

To restore the FM/AM tuner

Press and hold FM AM (DAB) again.

Storing DAB services in memory

You can preset up to 6 DAB services in each
DAB band (DAB1, DAB2, and DAB3) manually.

Before you start....

Press FM AM (DAB) briefly if tape, CD changer,
or external component is the current source.

1

Select the DAB tuner.

Each time you press and
hold the button, the DAB
tuner and the FM/AM tuner
are alternately selected.

ENGLISH

Service name

Ensemble name

Channel number

Frequency

FM/AMDAB

2

Select the DAB band (DAB1, DAB2,
or DAB3) you want.

Each time you press the
button, the DAB band
changes as follows:

DAB1

(D1)

CONTINUED ON THE NEXT PAGE

DAB2

(D2)

DAB3

(D3)

37

3

Tune in to an ensemble you want.

Tuning in to a preset DAB
service

ENGLISH

4

Select a service of the ensemble you
want to listen to.

5

Press and hold the number button
(in this example, 1) you want to store
the selected service into for more
than 2 seconds.

Selected band/preset number and “MEMO”
(memory) appear alternately for a while.

To select the next service

To select the previous
service

You can easily tune in to a preset DAB service.
Remember that you must store services first. If
you have not stored them yet, “Storing DAB
services in memory” on pages 37 and 38.

Before you start....

Press FM AM (DAB) briefly if tape, CD changer,
or external component is the current source.

1

Select the DAB tuner.

Each time you press and
hold the button, the DAB
tuner and the FM/AM tuner
are alternately selected.

FM/AMDAB

2

Select the DAB band (DAB1, DAB2,
or DAB3) you want.

Each time you press the
button, the DAB band
changes as follows:

DAB1

(D1)

DAB2

(D2)

DAB3

(D3)

6

Repeat the above procedure to store
other DAB services into other preset
numbers.

Notes:

• You can only preset primary DAB services. If you
store a secondary service, its primary service will
be stored instead.

• A previously preset DAB service is erased when a
new DAB service is stored in the same preset
number.

• Preset DAB services are erased when the power
supply to the memory circuit is interrupted (for
example, during battery replacement). If this
occurs, preset the DAB services again.

3

Select the number (1 – 6) for the
preset DAB service (primary) you
want.

Note:

If the selected primary service has some secondary
services, pressing the same number button repeatedly
will tune in to the secondary services.

38

What you can do more with
DAB

Tracing the same program automatically
(Alternative Reception)

You can keep listening to the same program.

• While receiving a DAB service:

When driving in an area where a service
cannot be received, this unit automatically
tunes in to another ensemble or FM RDS
station, broadcasting the same program.

• While receiving an FM RDS station:

When driving in an area where a DAB service
is broadcasting the same program as the
FM RDS station is broadcasting, this unit
automatically tunes in to the DAB service.

Note:

When reception switches between DAB and FM, the
listening volume level may increase or decrease
inconveniently. This change in the volume level results
from unequal audio injection levels at broadcaster
site, but not from the malfunction of this unit.
To prevent this inconvenience, you can adjust the DAB
volume level (see the right column).

To use Alternative Reception

Note:

When Alternative Reception (for DAB services) is
activated, Network-Tracking Reception (for RDS
stations: see page 12) is also activated automatically.
On the other hand, Network-Tracking Reception
cannot be deactivated without deactivating
Alternative Reception.

To adjust the DAB volume level

You can adjust the volume level of DAB tuner
and store it in memory. By adjusting the volume
level properly to match it to the FM sound level,
you will not need to adjust the volume level each
time you change the source.
When shipped from the factory, DAB volume
level is set at “00.”

• See also “Changing the general settings
(PSM)” on page 25.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items
appears on the display.

2 Press ¢ or 4 to select “DAB VOL”

(DAB volume).

3 Turn the control dial to set to the desired

volume.
You can set it from “VOL –12” to “VOL 12.”

4 Press SEL (select) to finish the setting.

ENGLISH

When shipped from the factory, Alternative
Reception is activated.

• See also “Changing the general settings
(PSM)” on page 25.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items
appears on the display.

2 Press ¢ or 4 to select “DAB AF”

(alternative frequency).

3 Turn the control dial to select the desired

mode.

• AF ON: Traces the program among DAB
services and FM RDS stations
—Alternative Reception. The AF
indicator lights up on the display
(see page 12).

• AF OFF: Alternative Reception is
deactivated.

4 Press SEL (select) to finish the setting.

39

TROUBLESHOOTING

What appears to be trouble is not always serious. Check the following points before calling a service
center.

ENGLISH

• Sound cannot be heard

• This unit does not work at

General

• SSM (Strong-station

FM/AM

• Static noise while listening

Symptoms

from the speakers.

all.

Sequential Memory)
automatic preset does not
work.

to the radio.

Causes

The volume level is set to the
minimum level.

Connections are incorrect.

The built-in microcomputer
may have functioned
incorrectly due to noise, etc.

Signals are too weak.

The aerial is not connected
firmly.

Remedies

Adjust it to the optimum level.

Check the cords and
connections.

Press the reset button on the
panel holder after detaching the
control panel. (The clock setting
and preset stations stored in
memory are erased.)
(See page 2.)

Store stations manually.

Connect the aerial firmly.

• A cassette tape cannot be
ejected.

• A cassette tape cannot be
inserted.

• Cassette tapes become
hot.

Tape Playback

• Tape sound is at very low
level and sound quality is
degraded.

Cassette is locked.

You have tried to insert a
cassette in the wrong way.

This is not a malfunction.

The tape head is dirty.

Unlock the cassette.
(See page 22.)

Insert the cassette with the
exposed tape facing right.

Clean it with a head cleaning
tape.

40

Symptoms

Causes

Remedies

• “NO DISC” appears on the
display.

• “NO MAG” appears on the
display.

• “NO FILES” appears on the
display.

• MP3 disc is skipped or
cannot be played back.

• Noise is generated while
playing an MP3 disc.

No disc is in the magazine.

Discs are inserted upside down.

Discs are unplayable.

No magazine is loaded in the
CD changer.

The current disc does not
contain any MP3 files.

MP3 files do not have the
extension code—mp3 in their
file names.

MP3 files are not recorded in
the format compliant with ISO
9660 Level 1, Level 2, or Joliet.

The file played back is not an
MP3 file (although it has the
extension code—mp3).

Insert discs into the
magazine.

Insert discs correctly.

Insert playable discs.

Insert the magazine.

Insert a disc that contains
MP3 files.

Add the extension code
—mp3 to their file names.

Change the disc.
(Record MP3 files using a
compliant application.)

Skip to another file or change
the disc. (Do not add the
extension code—mp3 to non­MP3 files.)

ENGLISH

• A longer readout time is
required for an MP3 disc
(“CHECK” keeps flashing on
the display).

• MP3 files cannot be played
back as you have intended
them to play.

• Elapsed playing time is not
correct for an MP3 disc.

• “RESET 8” appears on the
display.

• “RESET 1” – “RESET 7”
appears on the display.

• The CD changer does not
work at all.

Readout time varies due to the
complexity of the folder/file
configuration.

Playback order is determined
when the files are recorded.

This sometimes occurs during
play. This is caused by how the
files are recorded on the disc.

This unit is not connected to the
CD changer correctly.

The built-in microcomputer may
have function incorrectly due to
noise, etc.

Do not use too many
hierarchies and folders. Also,
do not record any other types
of audio tracks together with
MP3 files.

Connect this unit and the
CD changer correctly and
press the reset button of the
CD changer.

Press the reset button of the
CD changer.

Press the reset button on the
panel holder after detaching
the control panel. (The clock
setting and preset stations
stored in memory are
erased.) (See page 2.)

CD Changer

41

MAINTENANCE

This unit requires very little attention, but you will
be able to extend the life of the unit if you follow
the instructions below.

To clean the head

ENGLISH

• Clean the heads after every 10 hours of use
using a wet-type head cleaning tape (available
at an audio store).
When the head becomes dirty, you may realize
the following symptoms:

– Sound quality is reduced.
– Sound level decreases.
– Sound drops out.

• Do not play dirty or dusty tapes.

• Do not touch the highly-polished head with any
metallic or magnetic tools.

CAUTION:

• Do not play the cassettes with peeling labels;
otherwise, they can damage the unit.

• Tighten tapes to remove slack since loose tape
may become entangled with the mechanism.

• Do not leave a cassette in the cassette
compartment after use, as the tape may become
slack.

The function below is also provided to ensure the
longer life of this unit.

Ignition key-off release/Ignition key-on
play

• Turning off the ignition key with a cassette in
the compartment automatically releases the
tape from the unit’s tapehead.

• Turning on the ignition key with a cassette in
the compartment starts playback automatically
if you turned off the ignition during tape play.

To keep the tape clean

• Always store the cassettes in their storage
cases after use.

• Do not store cassettes in the following places:

– Subject to direct sunlight
– With high humidity
– At extremely hot temperatures

42

SPECIFICATIONS

AUDIO AMPLIFIER SECTION

Maximum Power Output:

Front: 50 W per channel
Rear: 50 W per channel

Continuous Power Output (RMS):

Front: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than

0.8% total harmonic distortion.

Rear: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than

0.8% total harmonic distortion.
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:

Bass: ±10 dB at 100 Hz

Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:

2.0 V/20 kΩ load (250 nWb/m)

Output Impedance: 1 kΩ

TUNER SECTION

Frequency Range:

FM: 87.5 MHz to 108.0 MHz
AM: (MW) 522 kHz to 1 620 kHz

(LW) 144 kHz to 279 kHz

CASSETTE DECK SECTION

Wow & Flutter: 0.11% (WRMS)
Fast-Wind Time: 100 sec. (C-60)
Frequency Response (Dolby B NR OFF):

30 Hz to 16 000 Hz (Normal tape)

Signal-to-Noise Ratio: 56 dB (Normal tape)

(Dolby B NR ON): 65 dB
(Dolby B NR OFF): 56 dB

Stereo Separation: 40 dB

GENERAL

Power Requirement:

Operating Voltage: DC 14.4 V

(11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature: 0°C to +40°C
Dimensions (W × H × D):

Installation Size (approx.):

182 mm × 52 mm × 150 mm

Panel Size (approx.):

188 mm × 58 mm × 12 mm

Mass (approx.):

1.5 kg (excluding accessories)

ENGLISH

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:

16.3 dBf (1.8 µV/75 Ω)

Alternate Channel Selectivity (400 kHz):

65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 30 dB
Capture Ratio: 1.5 dB

[MW Tuner]

Sensitivity: 20 µV
Selectivity: 35 dB

[LW Tuner]

Sensitivity: 50 µV

Design and specifications are subject to change
without notice.

43

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

Haben Sie PROBLEME mit dem Betrieb?

Bitte setzen Sie Ihr Gerät zurück

Siehe Seite Zurücksetzen des Geräts

Vous avez des PROBLÈMES de fonctionnement?

Réinitialisez votre appareil

Référez-vous à la page intitulée Comment réinitialiser votre appareil

Hebt u PROBLEMEN met de bediening?

Zie de pagina met de paragraaf Het apparaat terugstellen

EN, GE, FR, NL

© 2003 VICTOR COMPANY OF JAPAN, LIMITED

Stel het apparaat terug

JVC

0403KKSMDTJEIN

1

53 mm

184 mm

KS-FX942R

Installation/Connection Manual
Einbau/Anschlußanleitung
Manuel d’installation/raccordement
Handleiding voor installatie/aansluiting

ENGLISH

• This unit is designed to operate on 12 V DC,
NEGATIVE ground electrical systems.

INSTALLATION
(IN-DASH MOUNTING)

• The following illustration shows a typical installation.
However, you should make adjustments
corresponding to your specific car. If you have any
questions or require information regarding
installation kits, consult your JVC IN-CAR
ENTERTAINMENT dealer or a company supplying
kits.

DEUTSCH

• Dieses Gerät ist für einen Betrieb in elektrischen
Anlagen mit 12 V Gleichstrom und (–) Erdung
ausgelegt.

EINBAU
(IM ARMATURENBRETT)

• Die folgende Abbildung zeigt einen typischen
Einbau. Dennoch müssen Sie entsprechend Ihrem
jeweiligen Auto Anpassungen vornehmen. Bei
irgendwelchen Fragen oder wenn Sie Informationen
hinsichtlich des Einbausatzes brauchen, wenden
Sie sich an ihren JVC Autoradiohändler oder ein
Unternehmen das diese Einbausätze vertreibt.

FRANÇAIS

• Cet appareil est conçu pour fonctionner sur des
sources de courant continu de 12 V à masse
NEGATIVE.

INSTALLATION (MONTAGE
DANS LE TABLEAU DE BORD)

• L’illustration suivante est un exemple d’installation
typique. Cependant, vous devez faire les
ajustements correspondant à votre voiture
particulière. Si vous avez des questions ou avez
besoin d’information sur des kits d’installation,
consulter votre revendeur d’autoradios JVC ou une
compagnie d’approvisionnement.

0403KKSMDTJEIN
EN, GE, FR, NL

1

Before mounting: Press (control panel
release button) to detach the control panel if
already attached.

* When shipped from the factory, the control

panel is packed in the hard case.

2

Remove the trim plate.

3

Remove the sleeve after disengaging the sleeve
locks.

1 Stand the unit.

Note: When you stand the unit, be careful
not to damage the fuse on the rear.

2 Insert the 2 handles between the unit and

the sleeve, as illustrated, to disengage the
sleeve locks.

3 Remove the sleeve.

Note: Be sure to keep the handles for future
use after installing the unit.

4

Install the sleeve into the dashboard.
* After the sleeve is correctly installed into the

dashboard, bend the appropriate tabs to hold
the sleeve firmly in place, as illustrated.

5

Fix the mounting bolt to the rear of the unit’s
body and place the rubber cushion over the end
of the bolt.

6

Do the required electrical connections.

7

Slide the unit into the sleeve until it is locked.

8

Attach the trim plate.
Note: Ensure the recessed part is at the bottom.
If not, the control panel will not open completely.

9

Attach the control panel.

1

Vor dem Einbau: Drücken Sie (Freigabe der
Schalttafel), um die Arretierung der Schalttafel zu
lösen, sofern diese bereits angebracht ist.

* Bei der Auslieferung ab Werk ist die Schalttafel

im Etui verpackt.

2

Den Frontrahmen herausnehmen.

3

Die Halterung nach dem Entriegeln der
Halterungensperren abnehmen.

1 Das Gerät aufstellen.

Hinweis: Beim Aufstellen des Geräts darauf
achten, daß die Sicherung auf der Rückseite
nicht beschädigt wird.

2 Die 2 Griffe zwischen dem Gerät und der

Halterung wie abgebildet einstecken und die
Halterungensperren entriegeln.

3 Die Halterung entfernen.

Hinweis: Sicherstellen, daß die Griffe für
künftigen Gebrauch nach dem Einbau des
Geräts aufbewahrt werden.

4

Die Halterung im Armaturenbrett einbauen.
* Nach dem korrekten Einbau der Halterung im

Armaturenbrett, die entsprechenden Riegel
umknicken, um die Halterung an ihrem Platz zu
sichern, siehe Abbildung.

5

Die Befestigungsschraube an der Rückseite des
Gerätekörpers befestigen und das Ende der
Schraube mit einem Gummipuffer abdecken.

6

Nehmen Sie die erforderlichen elektrischen
Anschlüsse vor.

7

Das Gerät in die Halterung schieben, bis es einrastet.

8

Befestigen Sie den Frontrahmen.
Hinweis: Vergewissern Sie sich, dass sich die

Aussparung an der Unterseite befindet. Ist dies
nicht der Fall, lässt sich die Bedienungsblende
nicht vollständig öffnen.

9

Die Schalttafel anbringen.

1

Avant le montage:

Appuyer sur (déblocage
du panneau de commande) pour éventeullement
détacher le panneau de commande.

* Lorsque ce panneau de commande sort d’usine,

il est rangé dans un étui de transport.

2

Retirer la plaque d’assemblage.

3

Libérer les verrous du manchon et retirer le manchon.

1

Poser l’appareil à la verticale.

Remarque:

Lorsque vous mettez l’appareil à la
verticale, faire attention de ne pas
endommager le fusible situé sur l’arrière.

2

Insérer les 2 poignées entre l’appareil et le
manchon comme indiqué pour désengagé les
verrous de manchon.

3

Retirer le manchon.

Remarque:

S’assurer de garder les poignées
pour une utilisation ultérieur, après l’installation
de l’appareil.

4

Installer le manchon dans le tableau de bord.
* Après installation correcte du manchon dans le

tableau de bord, plier les bonnes pattes pour
maintenir fermement le manchon en place,
comme montré.

5

Monter le boulon de montage sur l’arrière du corps
de l’appareil puis passer l’amortisseur en
caoutchouc sur l’extrémité du boulon.

6

Réalisez les connexions électriques.

7

Faire glisser l’appareil dans le manchon jusqu’à ce
qu’il soit verrouillé.

8

Attachez la plaque d’assemblage.

Remarque:

Assurez-vous que la partie encastrée
est en bas. Sinon, le panneau de commande ne
pourra pas être ouvert complètement.

9

Remonter le panneau de commande.

1

Voordat u aan de montage van het apparaat
begint: Druk op

(het bedieningspaneel
vrijgeven) als u het bedieningspaneel wilt
loskoppelen indien dit aan de eenheid is
vastgekoppeld.

* Standaard wordt het bedieningspaneel bij het

verlaten van de fabriek los verpackt meegeleverd.

2

Verwijder de sierplaat.

3

Verwijder het huis nadat u de klemmen hebt
losgemaakt.

1 Zet het apparaat rechtop.

Opmerking: Wanneer u het apparaat rechtop
zet, moet u erop letten dat u de zekering aan de
achterkant niet beschadigt.

2 Plaats de 2 hendels, zoals afgebeeld, tussen het

apparaat en het huis, om de klemmen los te
maken.

3 Verwijder het huis.

Opmerking: Bewaar de hendels nadat u het
apparaat hebt geïnstalleerd, zodat u ze ook in de
toekomst kunt gebruiken.

4

Installeer het huis in het dashboard.
* Nadat het huis op de juiste wijze in het dashboard

is geplaatst, moet u de palletjes, zoals afgebeeld,
stevig op hun plaats duwen.

5

Maak de bevestigingsbout aan de achterkant van het
apparaat vast en plaats de rubberdop over het uiteinde
van de bout.

6

Breng de vereiste elektrische verbindingen tot stand.

7

Schuif het apparaat in het huis totdat het vergrendeld is.

8

Bevestig een sierplaat.
Opmerking: Zorg dat het ingedeukte gedeelte onder

is. Het bedieningspaneel kan anders namelijk niet
geheel worden geopend.

9

Bevestig het bedieningspaneel.

GET0121-003A

[E/EX]

NEDERLANDS

• Dit apparaat mag worden gebruikt bij elektrische
systemen die werken op 12 V gelijkstroom met negatieve
aarding.

INSTALLATIE (INBOUW IN
HET DASHBOARD)

• Op de volgende afbeelding kunt u zien hoe de installatie,
normaal gesproken, in zijn werk gaat. U moet echter bij
de installatie rekening houden met de bijzonderheden
van uw eigen auto. Neem bij vragen of voor meer
bijzonderheden over inbouwpakketten contact op met uw
JVC car audio dealer of een dealer of een bedrijf dat
inbouwpakketten levert.

JVC

TROUBLESHOOTING

• The fuse blows.

* Are the red and black leads connected correctly?

• Power cannot be turned on.

* Is the yellow lead connected?

• No sound from the speakers.

* Is the speaker output lead short-circuited?

• Sound is distor ted.

* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded

in common?

• Unit becomes hot.

* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded

in common?

FEHLERSUCHE

• Die Sicherung brennt durch.

* Sind die roten und schwarzen Leitungen richtig

angeschlossen?

• Stromversorgung kann nicht eingeschaltet
werden.

* Ist die gelbe Leitung angeschlossen?

• Kein Ton aus den Lautsprechern.

*

Ist die Lautsprecherausgangsleitung kurzgeschlossen?

• Ton verzerrt.

* Ist die Lautsprecherausgangsleitung geerdet?
* Sind die (–) Anschlußklemmen der linken und

rechten Lautsprecher zusammen geerdet?

• Gerät wird heiß.

* Ist die Lautsprecherausgangsleitung geerdet?
* Sind die (–) Anschlußklemmen der linken und

rechten Lautsprecher zusammen geerdet?

EN CAS DE DIFFICULTES

• Le fusible saute.

* Les fils rouge et noir sont-ils racordés

correctement?

• L’appareil ne peut pas être mise sous tension.

*

Le fil jaune est-elle raccordée?

• Pas de son des enceintes.

* Le fil de sortie d’enceinte est-il cour t-circuité?

• Le son est déformé.

* Le fil de sortie d’enceinte est-il à la masse?
* Les bornes “–” des enceintes gauche et droit sont-

elles mises ensemble à la masse?

• L’appareil devient chaud.

* Le fil de sortie d’enceinte est-il à la masse?
* Les bornes “–” des enceintes gauche et droit sont-

elles mises ensemble à la masse?

PROBLEMEN OPLOSSEN

• De zekering slaat door.
* Zijn de rode en de zwarte draden op de juiste manier

aangesloten?

• De stroom kan niet worden ingeschakeld.
* Is de gele draad aangesloten?

• Er komt geen geluid uit de speakers.
* Is de uitgaande speakerdraad kortgesloten?

• Het geluid wordt vervormd.

* Is de uitgaande speakerdraad geaard?
* Zijn de “–” polen van de linker- en de rechterspeakers

gemeenschappelijk geaard?

• Het apparaat raakt verhit.

* Is de uitgaande speakerdraad geaard?
* Zijn de “–” polen van de linker- en de rechterspeakers

gemeenschappelijk geaard?

2

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat

9

8

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat

7

Sleeve

Halterung

Manchon

Huis

Mounting bolt

Befestigungsschraube

Boulon de montage

Bevestigingsbout

5

4

Dashboard

Armaturenbrett

Tableau de bord

Dashboard

Rubber cushion

Gummipuffer

Amortisseur en
caoutchouc

Rubberdop

Control panel

Schalttafel

Panneau de commande

Bedieningspaneel

See “ELECTRICAL CONNECTIONS.”

Siehe „ELEKTRISCHE ANSCHLÜSSE“.

Référez-vous “RACCORDEMENTS
ELECTRIQUES” .

Zie “ELEKTRISCHE VERBINDINGEN”.

6

*

4

3

Handle

Griff

Poignée

Hendel

Fuse

Sicherung

Fusible

Zekering

Slot

Schlitz

Fente

Sleuf

Lock Plate

Arretierplättchen

Plaque de verrouillage

Vergrendelingsplaat

Sleeve

Halterung

Manchon

Huis

1

Control panel

Schalttafel

Panneau de commande

Bedieningspaneel

2

• When installing the unit without using the sleeve

• Beim Einbau des Geräts ohne Halterung

• Lors de l’installation de l’appareil scans utiliser de manchon

• Wanneer u het apparaat zonder huis installeert

In a Toyota for example, first remove the car radio and install the unit in its place.

Zum Beispiel in einem Toyota zuerst das Autoradio ausbauen und dann das Gerät an seinem Platz einbauen.

Par exemple dans une Toyota, retirer d’abord l’autoradio et installer l’appareil à la place.

Voorbeeld: Bij een Toyota moet u eerst de autoradio verwijderen en daarna het apparaat installeren.

Removing the unit

• Before removing the unit, release the rear section.

1

Remove the control panel.

2

Remove the trim plate.

3

Insert the 2 handles into the slots, as shown.
Then, while gently pulling the handles away from
each other, slide out the unit. (Be sure to keep

the handles after installing it.)

Ausbau des Geräts

• Vor dem Ausbau des Geräts den hinteren Teil
freigeben.

1

Den Schalttafel abnehmen.

2

Den Frontrahmen herausnehmen.

3

Die 2 Griffe in die Schlitze wie gezeigt stecken.
Dann die Griffe behutsam auseinander ziehen
und das Gerät herausziehen. (Die Griffe nach

dem Einbau auf jeden Fall aufbewahren.)

Retrait de l’appareil

•

Avant de retirer l’appareil, libérer la section arrière.

1

Retirer le panneau de commande.

2

Retirer la plaque d’assemblage.

3

Introduire les 2 poignées dans les fentes, comme
montré. Puis, tout en tirant doucement les
poignées écartées, faire glisser l’appareil pour le
sortir.

(S’assurer de conserver les poignées

après l’installation de l’appareil.)

Verwijderen van het apparaat

• Voordat u het apparaat verwijdert, moet u het

achtergedeelte losmaken.

1

Verwijder het bedieningspaneel.

2

Verwijder de sierplaat.

3

Plaats de 2 hendels, zoals afgebeeld, in de sleuven.
Daarna duwt u de hendels zachtjes uit elkaar en kunt u
het apparaat naar buiten schuiven. (Bewaar de

hendels nadat u het apparaat hebt
geïnstalleerd!)

RACCORDEMENTS ELECTRIQUES

Pour éviter tout court-circuit, nous vous
recommandons de débrancher la borne négative de
la batterie et d’effectuer tous les raccordements
électriques avant d’installer l’appareil. Si l’on n’est pas
sûr de pouvoir installer correctement cet appareil, le
faire installer par un technicien qualifié.

Remarque:

Cet appareil est conçu pour fonctionner sur des
sources de courant continu de

12 V à masse

NEGATIVE

. Si votre véhicule n’offre pas ce type
d’alimentation, il vous faut un convertisseur de
tension, que vous pouvez acheter chez un revendeur
d’autoradios JVC.

•

Remplacer le fusible par un de la valeur précisée. Si
le fusible saute souvent, consulter votre revendeur
d’autoradios JVC.

•

Si le bruit est un problème...
Cet appareil incorpore un filtre de bruit dans le
circuit d’alimentation. Cependant, avec certains
véhicules, quelques claquements ou autres bruits
non désirés risquent de se produire. Si cela arrive,
raccorder la

borne arrière de masse

de l’appareil
au châssis de la voiture (voir le diagramme de
raccordement) en utiliscant des cordons les plus
gros et les plus courts possibles telle qu’une barre
de cuivre ou une tresse. Si le bruit persiste,
consulter votre revendeur d’autoradios JVC.

•

La puisscance admissible des enceintes devrait
supérieure à 50 W à l’arrière et à 50 W l’avant, avec
une impédance de

4 Ω à 8 Ω

.

• S’assurer de raccorder la mise à la masse de
cet appareil au châssis de la voiture.

•

Le dissipateur de chaleur devient très chaud après
usage. Faire attention de ne pas le toucher en
retirant cet appareil.

ELEKTRISCHE ANSCHLÜSSE

Zur Vermeidung von Kurzschlüssen empfehlen wir,
daß Sie den negativen Batterieanschluß abtrennen
und alle elektrischen Anschlüsse herstellen, bevor
das Gerät eingebaut wird. Sind Sie sich über den
richtigen Einbau des Geräts nicht sicher, lassen Sie
es von einem qualifizierten Techniker einbauen.

Hinweis:
Dieses Gerät ist für einen Betrieb in elektrischen
Anlagen mit 12 V Gleichstrom und (–) Erdung
ausgelegt. Verfügt Ihr Fahrzeug nicht über diese

Anlage, ist ein Spannungsinverter erforderlich, der
bei JVC Autoradiohändler erworben werden kann.

• Die Sicherung mit einer der entsprechenden
Nennleistung ersetzen. Brennt die Sicherung
häufig durch, wenden Sie sich an ihren JVC
Autoradiohändler.

• Sind Störgeräusche ein Problem...
Dieses Gerät enthält ein Störfilter im Stromkreis. Bei
manchen Fahrzeugen kann jedoch ein Klicken
oder andere unerwünschte Störgeräusche
auftreten. Sollte das der Fall sein, die hintere
Erdungscanschlußklemme (siehe Schaltplan) des
Geräts am Fahrwerk des Fahrzeugs anschließen,
dabei kürzere und dickere Kabel wie
beispielsweise Kupfergeflechtdraht oder Stahldraht
verwenden. Bleibt Störgeräusch bestehen, wenden
Sie sich an Ihren JVC Autoradiohändler.

• Die maximale Eingangsleistung der Lautsprecher
sollte mehr als 50 W hinten und 50 W vorn bei einer
Impedanz von 4 Ω bis 8 Ω betragen.

• Sicherstellen, daß das Gerät am Fahrwerk

geerdet wird.

• Das Abstrahlblech wird nach dem Gebrauch sehr
heiß. Beim Ausbau des Geräts darauf achten, das
Abstrahlblech nicht zu berühren.

ELEKTRISCHE VERBINDINGEN

Om kortsluiting te voorkomen adviseren wij u om de
minpool van de accu los te maken en alle elektrische
verbindingen tot stand te brengen voordat u het apparaat in
de auto installeert. Als u niet zeker weet hoe u dit apparaat
moet installeren, kunt u dit beter door een daartoe
gekwalificeerde technicus laten doen.

Opmerking:

Dit apparaat mag worden gebruikt bij elektrische systemen
die werken op 12 V gelijkstroom met negatieve
aarding. Als uw auto niet is uitgerust met een dergelijk
systeem, is een spanningsomzetter vereist. Dit instrument
kan worden aangeschaft bij JVC car audio dealers.

• Vervang de zekering door een exemplaar met het
aangegeven vermogen. Als de zekering vaak doorslaat,
moet u uw JVC car audio dealer raadplegen.

• Als u geluidsproblemen hebt…
De krachtschakeling van dit apparaat heeft een ingebouwd
geluidsfilter. In sommige voertuigen zijn tikgeluiden of
andere ongewenste geluiden te horen. Als dit gebeurt,
moet u de massaklem aan de achterkant (zie
aansluitingsschema) aan het chassis van de auto
vastmaken met behulp van een kortere en dikkere kabel,
zoals kopermanteldraad of tellerkabel. Als het geluid niet
verdwijnt, moet u contact opnemen met uw JVC car audio
dealer.

• Het maximum ingangsvermogen van de speakers moet
achterin meer dan 50 W zijn en voorin 50 W, met een
impedantie van 4 Ω tot 8 Ω.

• Zorg ervoor dat dit apparaat door middel van een

aardkabel is verbonden met het chassis van de
auto.

• De warmte-opnemer kan na gebruik erg heet worden.
Raak de warmte-opnemer niet aan wanneer u dit apparaat
van zijn plaats haalt.

Note : When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If longer screws are used,

they could damage the unit.

Hinweis : Beim Anbringen des Gerät an der Konsole sicherstellen, daß 6 mm lange Schrauben verwendet werden. Werden

längere Schrauben verwendet, können sie das Gerät beschädigen.

Remarque :

Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis d’une longueur de 6 mm. Si des
vis plus longues sont utilisées, elles peuvent endommager l’appareil.

Opmerking : Wanneer u het apparaat aan de bevestigingsklem vastmaakt, moet u de 6 mm lange schroeven gebruiken. Als u langere schroeven

gebruikt, kan het apparaat worden beschadigd.

• When using the optional stay

• Beim Verwenden der Anker-Option

• Lors de l’utilisation du hauban en option

• Wanneer u de steun gebruikt (facultatief)

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you
disconnect the battery’s negative terminal and make all
electrical connections before installing the unit. If you
are not sure how to install this unit correctly, have it
installed by a qualified technician.

Note:
This unit is designed to operate on 12 V DC,
NEGATIVE ground electrical systems. If your vehicle

does not have this system, a voltage inverter is
required, which can be purchased at JVC IN-CAR
ENTERTAINMENT dealers.

• Replace the fuse with one of the specified rating. If
the fuse blows frequently, consult your JVC IN-CAR
ENTERTAINMENT dealer.

• If noise is a problem...
This unit incorporates a noise filter in the power
circuit. However, with some vehicles, clicking or other
unwanted noise may occur. If this happens, connect
the unit’s rear ground terminal (see connection
diagram) to the car’s chassis using shorter and
thicker cords, such as copper braiding or gauge wire.
If noise still persists, consult your JVC IN-CAR
ENTERTAINMENT dealer.

• Maximum input of the speakers should be more than
50 W at the rear and 50 W at the front, with an
impedance of 4 Ω to 8 Ω.

• Be sure to ground this unit to the car’s chassis.

• The heat sink becomes very hot after use. Be careful

not to touch it when removing this unit.

Heat sink

Abstrahlblech

Dissipateur de chaleur

Warmte-opnemer

Handles

Griffe

Poignées

Hendels

Washer (ø5)

Unterlegscheibe (ø5)

Rondelle (ø5)

Sluitring (ø5)

Lock nut (M5)

Sicherungsmutter (M5)

Ecrou d’arrêt (M5)

Contra-moer (M5)

Mounting bolt (M5 x 20 mm)

Befestigungsschraube (M5 x 20 mm)

Boulon de montage (M5 x 20 mm)

Bevestigingsbout (M5 x 20 mm)

Rubber cushion

Gummipuffer

Amortisseur en caoutchouc

Rubberdop

Teileliste für den Einbau und
Anschluß

Die folgenden Teile werden zusammen mit diesem
Gerät geliefert.
Nach ihrer Überprüfung, die Teile richtig einsetzen.

Liste des pièces pour l’installation et
raccordement

Les pièces suivantes sont fournies avec cet appareil.
Après vérification, veuillez les placer correctement.

Lijst van onderdelen die u bij
installatie en aansluiting nodig hebt

De volgende onderdelen worden bij het apparaat geleverd.
Installeer ze op de juiste wijze, nadat u ze hebt
gecontroleerd.

Parts list for installation and
connection

The following parts are provided with this unit.
After checking them, please set them correctly.

Hard case/Control panel

Etui/Schalttafel

Etui de transport/Panneau
de commande

Behuizing/Bedieningspaneel

Sleeve

Halterung

Manchon

Huis

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat

Power cord

Stromkable

Cordon d’alimentation

Stroomkabel

321

Control panel

Schalttafel

Panneau de commande

Bedieningspaneel

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat

Handle

Griff

Poignée

Hendel

Bracket*

Konsole*

Support*

Console*

Bracket*

Konsole*

Support*

Console*

* Not included with this unit.

* Nicht Teil dieses Geräts.

*

Non fourni avec cet appareil.

* Niet meegeleverd.

Flat type screws (M5 x 6 mm)*

Senkkopfschrauben (M5 x 6 mm)*

Vis à tête plate (M5 x 6 mm)*

Platkopschroeven (M5 x 6 mm)*

Pocke t

Taschen

Poche

Zak

Flat type screws (M5 x 6 mm)*

Senkkopfschrauben (M5 x 6 mm)*

Vis à tête plate (M5 x 6 mm)*

Platkopschroeven (M5 x 6 mm)*

Sleeve

Halterung

Manchon

Huis

Screw (option)

Schraube (Option)

Vis (en option)

Schroef (facultatief)

Lock nut

Sicherungsmutter

Ecrou d’arrêt

Contra-moer

Stay (option)

Anker (Option)

Hauban (en option)

Steun (facultatief)

Mounting bolt

Befestigungsschraube

Boulon de montage

Bevestigingsbout

Fire wall

Feuerwand

Cloison

Brandscherm

Washer

Unterlegscheibe

Rondelle

Sluitring

Dashboard

Armaturenbrett

Tableau de bord

Dashboard

Battery

Batterie

Pile

Batterij

Remote controller

Fernbedienung

Télécommande

Afstandsbediening

CR2025

Install the unit at an angle of less
than 30˚.

Stellen Sie das Gerät mit einem
Winkel von weniger als 30˚ auf.

Installez l’appareil avec un angle
de moins de 30˚.

Installeer het toestel met een hoek
kleiner dan 30˚.

Less than 30˚

Weniger als 30˚

Moins de 30˚

Kleiner dan 30˚

3

7

2

3

4

6

1

3

*

*

2

15

B1 B3 B5 B7

B2 B4 B6 B8

A5 A7

A2 A4

A8

A6

B1 B3 B5 B7

B2 B4 B6 B8

A5 A7

A2 A4

A8

A6

1

A8

A7

A5

A4

A2

B5B6

B4

B3 B8 B7 B2 B1

5

A6

(ILLUMINATION)

Before connecting: Check the wiring in the vehicle
carefully. Incorrect connection may cause serious
damage to this unit.
The leads of the power cord and those of the
connector from the car body may be different in
color.

1

Connect the colored leads of the power cord to
the car battery, speakers and power aerial (if any)
in the following sequence.

1 Black: ground
2 Yellow: to car battery (constant 12 V)
3 Red: to an accessory terminal
4 Blue with white stripe: to remote lead of other

equipment or power aerial if any (200 mA max.)

5 Orange with white stripe: to car light control

switch

6 Brown: to cellular phone system (For details,

refer to the instructions of the cellular phone.)

7 Others: to speakers

2

Connect the aerial cord.

3

Finally connect the wiring harness to the unit.

Note: If your vehicle does not have any accessory
terminal, move the fuse from the fuse position 1
(initial position) to fuse position 2, and connect the
red lead (A7) to the positive (+) battery terminal.

• The yellow lead (A4) is not used in this case.

Vor dem Anschließen: Die Verdrahtung im Fahrzeug
sorgfältig überprüfen. Falsche Anschlüsse können
ernsthafte Schäden am Gerät hervorrufen.
Die Leiter des Stromkabels und die Leiter des Anschlusses
im Fahrzeug können sich farblich unterscheiden.

1

Die farbigen Leitungen des Spannunsgversorgungskabels
an der Autobatterie, ontstekingsschakelaarden
Lautsprechern und dem Motorantenne (sofern vorhanden)
in folgender Reihenfolge anschließen.

1 Schwarz: Erdung
2 Gelb: an Autobatterie (konstant 12 V)
3 Rot: zur einer Zubehöranschlußklemme
4 Blau mit weißem Streifen: zum Zusatzkabel des

anderen Geräts oder der Motorantenne, sofern
vorhanden (max. 200 mA)

5 Orange mit weißem Streifen: zum Autolichtschalter
6 Braun: an Mobiltelefon (Weitere informationen

entnehmen Sie bitte der Bedienungscanleitung
des Mobiltelefons.)

7 Andere: zur Lautsprecher

2

Das Antennenkabel anschließen.

3

Die Kabelbäume am Gerät anschließen.

Hinweis: Verfügt Ihr Fahrzeug nicht über eine
Zubehöranschlußklemme, die Sicherung von der 1.
Sicherungsposition (Erstposition) in die 2.
Sicherungsposition versetzen, die rote Leitung (A7) an
der (+) Batterieanschlußklemme anschließen.

•

Die gelbe Leitung (A4) wird in diesem Fall nicht verwendet.

Avant de commencer la connexion:

Vérifiez
attentivement le câblage du véhicule. Une connexion
incorrecte peut endommager sérieusement l’appareil.
Le fil du cordon d’alimentation et ceux des
connecteurs du châssis de la voiture peuvent être
différents en couleur.

1

Connectez les fils de couleur du cordon d’alimentation
à la batterie de la voiture, aux enceintes et à l’antenne
automatique (s’il y en a une) dans l’ordre suivant.

1

Noir: à la masse

2

Jaune: à la batterie de la voiture (12 V constant)

3

Rouge: à une borne accessoire

4

Bleu avec bande blanche: au fil de télécommande
de l’autre appareil ou à l’antenne automatique s’il
y en a une (200 mA max.)

5

Orange avec bande blanche: à l’interrupteur
d’éclairage de la voiture

6

Marron: à un système de téléphone cellulaire
(Pour les détails, se référer aux instructions du
téléphone cellulaire.)

7

Autres: aux enceintes

2

Connectez le cordon d’antenne.

3

Finalement, connectez le faisceau de fils à l’appareil.

Remarque:

Si votre véhicule ne possède pas de borne
accessoire, déplacez le fusible de la position de fusible
1 (position originale) à la position de fusible 2 et connectez
le fil rouge (A7) à la borne positive (+) de la batterie.

• Le fil jaune (A4) n’est pas utilisé dans ce cas.

Alvorens te verbinden: Controleer de bedrading in de
auto zorgvuldig. Het apparaat kan door verkeerde
verbinding ernstige schade oplopen.
De draden van het stroomsnoer verschillen mogelijk van
kleur met de aansluitingen op het chassis van de auto.

1

Sluit de gekleurde snoerdraden van de stroomkable in
de hierna genoemde volgorde aan op de accu van de
auto, de luidsprekers en de antenne (indien aanwezig).

1 Zwart: aarde
2 Geel: naar de accu van de auto (constant 12 V)
3 Rood: naar de aansluitklem van de accessoire
4 Blauw met witte streep: naar afstandsbedieningsdraad

van andere apparatuur of antenne met circuit indien
aanwezig (200 mA max.)

5 Oranje met witte streep: naar de schakelaar voor de

autoverlichting

6 Bruin: naar het mobiele-telefoonsysteem (Lees

voor meer informatie de instructies die bij de
mobiele telefoon worden geleverd.)

7 Andere: naar de speakers

2

Sluit de antenne aan.

3

Verbind de draadbundel daarna met het apparaat.

Opmerking: Als uw voertuig niet beschikt over een
aansluitklem, moet u de zekering verplaatsen van stand 1
(beginstand) naar stand 2 en moet u de rode draad (A7)
met de pluspool (+) van de accu verbinden.

• In dit geval wordt de gele draad (A4) niet gebruikt.

Typical Connections / Typische Anschlüsse / Raccordements typiques / Normale verbindingen

Line out
(see diagram )

Schutz kappen
Signalausgang
(siehe Schaltplan )

Sortie de ligne
(voir le diagramme )

Uitgang (zie schema )

Fuse block

Sicherungsblock

Porte-fusible

Zekeringblok

To metallic body or chassis of the car

Zur metallenen Karosserie oder zum Fahrwerk des Autos

Vers corps métallique ou châssis de la voiture

Naar metalen ondergrond of chassis van de auto

To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch)

Zur einer stromführenden Anschlußklemme im Sicherungsblock
zum Anschließen an die Autobatterie (Umgehen des
Zündschalters)

A une borne sous tension du porte-fusible connectée à la batterie
de la voiture (en dérivant l’interrupteur d’allumage)

Naar een onder spanning staande aansluitklem in het zekeringblok die is
aangesloten op de accu van de auto (u passeert de ontstekingsschakelaar)

To remote lead of other equipment or power aerial if any

Zum Zusatzkabel des anderen Geräts oder der Motorantenne, sofern vorhanden

Au fil de télécommande de l’autre appareil ou à l’antenne automatique s’il y en a une

Naar afstandsbedieningsdraad van andere apparatuur of antenne met circuit indien aanwezig

To an accessory terminal in the fuse block

Zur einer Zubehöranschlußklemme im Sicherungsblock

Vers borne accessoire du porte-fusible

Naar een aansluitklem in het zekeringblok

Red

Rot

Rouge

Rood

Yellow*

1

Gelb*

1

Jaune*

1

Geel *

1

Aerial terminal

Antennenanschlußklemme

Borne de l’antenne

Aansluitpunt antenne

To aerial

Zur Antenne

A l’antenne

Naar de antenne

Rear ground terminal

Hintere
Erdungscanschlußklemme

Borne arrière de masse

Massaklem aan de
achterkant

Blue with white stripe

Blau mit weißem Streifen

Bleu avec bande blanche

Blauw met witte streep

*1 : Before checking the operation of this unit prior to

installation, this lead must be connected, otherwise
power cannot be turned on.

*1 : Vor der Überprüfung der Funktionsfähigkeit des Geräts

vor dem Einbau, muß diese Leitung angeschlossen
werden, da sonst die Stromversorgung nicht
eingeschaltet werden kann.

*1 : Pour vérifier le fonctionnement de cet appareil avant

installation, ce fil doit être raccordé, sinon l’appareil ne
peut pas être mis sous tension.

*1 : Voordat u controleert of het apparaat werkt (alvorens het te

installeren), moet deze draad aangesloten zijn. Als dit niet het
geval is, kan de stroom niet worden ingeschakeld.

White

Weiß

Blanc

Wit

Gray with black stripe

Grau mit schwarzem
Streifen

Gris avec bande noire

Grijs met zwarte streep

Green

Grün

Ver t

Groen

Purple

Lila

Violet

Paars

White with black stripe

Weiß mit schwarzem
Streifen

Blanc avec bande noire

Wit met zwarte streep

Green with black stripe

Grün mit schwarzem
Streifen

Vert avec bande noire

Groen met zwarte streep

Purple with black stripe

Lila mit schwarzem
Streifen

Violet avec bande noire

Paars met zwarte streep

Left speaker (front)

Linker Lautsprecher (vorne)

Enceinte gauche (avant)

Linkerspeaker (voorin)

Right speaker (front)

Rechter Lautsprecher (vorne)

Enceinte droit (avant)

Rechterspeaker (voorin)

Left speaker (rear)

Linker Lautsprecher (hinten)

Enceinte gauche (arrière)

Linkerspeaker (achterin)

Right speaker (rear)

Rechter Lautsprecher (hinten)

Enceinte droit (arrière)

Rechterspeaker (achterin)

Gray

Grau

Gris

Grijs

15 A fuse / 15 A Sicherung /

Fusible 15 A /

Zekering 15 A

Not included with this unit.

Wird nicht mit Gerät mitgeliefert.

Non fourni avec cet appareil.

Niet bij het apparaat inbegrepen.

*

Ignition switch

Zündschalter

Interrupteur d’allumage

Ontstekingsschakelaar

FRANÇAIS

DEUTSCH

NEDERLANDS

ENGLISH

Fuse position 2 / 2. Sicherungsposition /

Position de fusible 2

/ Zekering, stand 2

To cellular phone system

Zur Moblitelephon

A un système de téléphone
cellulaire

Naar het mobiele-telefoonsysteem

PRECAUTIONS on power supply and
speaker connections:

• DO NOT connect the speaker leads of the power

cord to the car battery; otherwise, the unit will
be seriously damaged.

• Connect the black lead (ground), yellow lead (to car
battery, constant 12 V), and red lead (to an
accessory terminal) correctly.

• BEFORE connecting the speaker leads of the
power cord to the speakers, check the speaker
wiring in your car.

– If the speaker wiring in your car is as

illustrated in Fig. 1 and Fig. 2 below, DO NOT

connect the unit using that original speaker wiring.
If you do, the unit will be seriously damaged.
Redo the speaker wiring so that you can connect
the unit to the speakers as illustrated in Fig. 3.

– If the speaker wiring in your car is as

illustrated in Fig. 3, you can connect the unit

using the original speaker wiring in your car.

– If you are not sure of the speaker wiring of your

car, consult your car dealer.

VORSICHTSMASSREGELN beim
Anschließen der Stromversorgung und
Lautsprecher:

• Die Lautsprecherleitungen des Netzkabels

NICHT an der Autobatterie anschließen, da
sonst das Gerät schwer beschädigt wird.

• Die schwarze Leitung (Erdung), die gelbe Leitung
(zur Autobatterie, konstant 12 V) und die rote Leitung
(zur Zubehöranschlußklemme) richtig anschließen.

• VOR dem Anschließen der Lautsprecherleitungen
des Spannunsgversorgungskabels an die
Lautsprecher, die Lautsprecherverdrahtung in
Ihrem Auto überprüfen.
– Ist die Lautsprecherverdrahtung wie unten in

„Fig. 1“ und „Fig. 2“ abgebildet, das Gerät
NICHT mit der Originalverdrahtung der
Lautsprecher anschließen, da sonst das Gerät
schwer beschädigt wird.
Die Lautsprecherverdrahtung erneuern, so daß
Sie das Gerät an den Lautsprechern wie in
„Fig. 3“ abgebildet anschließen können.

– Ist die Lautsprecherverdrahtung in Ihrem Auto

wie in „Fig. 3“ abgebildet, können Sie das Gerät
mit der Originalverdrahtung der Lautsprecher in
Ihrem Auto anschließen.

– Sind Sie sich über die Lautsprecherverdrahtung

in Ihrem Auto nicht sicher, wenden Sie sich an
Ihren Autohändler.

PRECAUTIONS sur l’alimentation et la
connexion des enceintes:

• NE CONNECTEZ PAS les fils d’enceintes du

cordon d’alimentation à la batterie; sinon,
l’appareil serait sérieusement endommagé.

•

Connectez correctement le fil noir (a la masse), le fil
jaune (a la batterie de la voiture,12 V constant) et le
fil rouge (à la prise accessoire).

•

AVANT de connecter les fils d’enceintes du cordon
d’alimentation aux enceintes, vérifiez le câblage
des enceintes de votre voiture.

–

Si le câblage des enceintes de votre voiture
est comme montré sur la Fig. 1 ou Fig. 2
ci-dessous,

NE CONNECTEZ PAS l’appareil en
utiliscant ce câblage original des enceintes. Si
vous le faites, l’appareil sera sérieusement
endommagé.
Recommencez le câblage des enceintes de façon
que vous puissiez connecter l’appareil aux
enceintes comme montré sur la Fig. 3.

–

Si le câblage des enceintes de votre voiture
est comme montré sur la Fig. 3,

vous pouvez
connecter l’appareil en utiliscant ce câblage
original d’enceintes pour votre voiture.

– Si vous n’êtes pas sûrs du câblage d’enceintes de

votre voiture, consulter le concessionnaire de
votre voiture.

VOORZORGSMAATREGELEN bij het
verbinden van de stroomkabeldraad
met de speakers:

• Verbind de speakerdraden van de stroomkabel
NIET met de accu van de auto; als u dit wel doet,
zal het apparaat ernstige schade oplopen.

• Sluit de zwarte draad (aarde), de gele draad (naar de accu
van de auto, constant 12 V) en de rode draad (naar de
aansluitklem van de accessoire) op de juiste wijze aan.

• VOORDAT u de speakerdraden van de stroomkabel
met de speakers verbindt, moet u de bedrading van de
speakers in uw auto controleren.
– Als de bedrading van de speakers eruitziet

zoals hieronder staat afgebeeld in Fig. 1 en
Fig. 2, mag het apparaat NIET worden aangesloten

met behulp van deze oorspronkelijke
speakerbedrading. Als u dat wel doet, zal het
apparaat ernstige schade oplopen.
Pas de bedrading van de speakers aan, zodat u het
apparaat met de speakers kunt verbinden, zoals staat
afgebeeld in Fig. 3.

– Als de bedrading van de speakers eruitziet

zoals staat afgebeeld in Fig. 3, kunt u het
apparaat aansluiten met behulp van de
oorspronkelijke speakerbedrading in uw auto.

– Als u twijfels hebt over de speakerbedrading in uw

auto, moet u contact opnemen met uw autodealer.

Brown / Braun /

Marron

/ Bruin

Black

Schwarz

Noir

Zwart

Fig. 2 Fig. 3Fig. 1

L

R

+

-

+

-

+

-

+

-

L

R

+

-

+

-

+

-

+

-

L

R

+

-

+

-

+

-

+

-

Fuse position 1 / 1. Sicherungsposition /

Position de fusible 1 /

Zekering, stand 1

To steering wheel remote
controller (see diagram )

An Lenkradfernbedienung
(siehe Schaltplan )

Pour la télécommande de
volant(voir le diagramme )

Naar stuurwiel-afstandsbediening
(zie schema )

We recommend you to connect the
JVC MP3-compatible CD changer. You
can also connect other CH-X series
CD changers (except CH-X99 and
CH-X100).

• You cannot use the KD-MK series
CD changers with this unit.

You can also use an external
component such as a portable MD
player by connecting the Line Input
Adapter KS-U57 (not supplied). (See
diagram .)

Wir empfehlen Ihnen, den MP3­kompatiblen CD-Wechsler von JVC
anzuschließen. Sie können auch
andere CD-Wechsler der Serie CH-X
anschließen (außer CH-X99 und
CH-X100).

• CD-Wechsler der Serie KD-MK
können mit diesem Gerät nicht
verwendet werden.

Sie können auch eine externe
Komponente, z.B. einen tragbaren
MD-Spieler, verwenden, wenn Sie den
(nicht zum Lieferumfang gehörenden)
Line-Eingangsadapter KS-U57
anschließen (siehe Schaltplan ).

Nous vous recommandons de
connecter le changeur de CD
compatible MP3 JVC. Vous pouvez
aussi connecter d’autres changeurs
de CD de la série CH-X (sauf le
CH-X99 et le CH-X100).

• Vous ne pouvez pas utiliser les
changeurs de CD de la série
KD-MK avec cet appareil.

Vous pouvez aussi utiliser un appareil
extérieur tel qu’un lecteur de MD en
connectant l’adaptateur d’entrée de
ligne KS-U57 (non fourni). (Voir le
diagramme ).

Sluit bij voorkeur de JVC, MP3
compatibele CD-wisselaar aan. U kunt
tevens bepaalde andere CD-wisselaars uit
de CH-X serie aansluiten (uitgezonderd de
CH-X99 en CH-X100).

• U kunt CD-wisselaars uit de KD-MK
serie niet met dit toestel gebruiken.

Het is ook mogelijk een extern apparaat
zoals een draagbare MD-speler aan te
sluiten met behulp van de Line Input
Adapter KS-U57 (niet meegeleverd). (Zie
schema .)

JVC CD changer/DAB tuner
or another external
component

CD-Wechsler von JVC/DAB­Tuner oder eine andere
externe Komponente

Changeur CD JVC/Tuner
DAB ou autre appareil
extérieur

JVC CD-wisselaar/DAB-tuner
of een ander extern apparaat

Orange with white stripe

Orange mit weißem Streifen

Orange avec bande blanche

Oranje met witte streep

To car light control switch

Zum Autolichtschalter

A l’interrupteur d’éclairage de la voiture

Naar de schakelaar voor de autoverlichting

4

INPUT

R

L

L

R

LRL

R

R

L

LINE

REAR

FRONT

*

2

OUT

R

L

R

L

R

L

INPUT

*

2

You can connect an amplifier and other equipment to
upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to
the remote lead of the other equipment so that it
can be controlled through this unit.

• For amplifier only:
– Connect this unit’s line-out terminals to the

amplifier’s line-in terminals.

– Disconnect the speakers from this unit,

connect them to the amplifier. Leave the
speaker leads of this unit unused. (Cover the
terminals of these unused leads with
insulating tape, as illustrated above.)

Sie können einen Verstärker oder ein anderes Gerät
anschließen, um Ihre Autostereoanlage zu erweitern.

• Schließen Sie das Fer nbedienungskabel (blau mit
weißem Streifen) an das Fernbedienungskabel des
anderen Geräts an, so daß es über dieses Gerät
gesteuert werden kann.

• Nur für den Verstärker:
– Die Anschlußklemmen am Ausgang dieses Gerät

an den Anschlußklemmen des Eingangs des
Verstärkers anschließen.

– Die Lautsprecher von diesem Gerät abtrennen

und am Verstärker anschließen. Die
Lautsprecherleitungen dieses Geräts unbenutzt
lassen. (Die Anschlußklemmen dieser nicht
verwendeten Leitungen mit Isolierklebeband
umwickeln, siehe Abbidung oben.)

Vous pouvez connecter un amplificateur ou autre
appareil pour améliorer votre système autoradio.

• Connectez le fil de commande à distance (bleu
avec bande blanche) au fil de commande à
distance de l’autre appareil de façon qu’il puisse

être commandé via cet appareil.

• Pour l’amplificateur seulement:
– Raccorder les bornes de sor tie ligne de cet appareil

aux bornes d’entrée ligne de l’amplificateur.

–

Déconnectez les enceintes de cet appareil et
connectez-les à l’amplificateur. Laissez les fils
d’enceintes de cet appareil inutilisés.
(Recouvrir les extrémités de ces fils inutilisés
avec de la bande isolante comme montré ci­dessus.)

Het is mogelijk om uw autostereosysteem uit te breiden
met een versterker of andere apparatuur.

• Verbind de afstandsbedieningsdraad (blauw met witte
streep) met de afstandsbedieningsdraad van andere
apparatuur zodat deze op afstand via dit apparaat kan
worden bediend.

• Alleen voor een versterker:
– Verbind de uitgang van het apparaat met de ingang

van de versterker.

– Koppel de speakers van dit apparaat los en

verbind ze aan de versterker. Gebruik de
speakerdraden van dit apparaat niet. (Plak
de aansluitklemmen van deze
speakerdraden met isolatieband af zoals
hierboven is afgebeeld.)

Connections Adding Other Equipment / Anschlüsse zum Hinzufügen von anderer Ausrüstung / Raccordement pour ajouter d’autres appareils /
Aansluitingen voor het toevoegen van andere apparatuur

Amplifier / Verstärker / Amplificateur / Versterker

Twist the core wires when connecting.

Die Kerndrähte beim Anschließen verdrehen.

Torsader les âmes des fils en les raccordant.

Draai de kerndraden om elkaar heen
wanneer u ze wilt aansluiten.

CAUTION / VORSICHT / PRECAUTION / LET OP!:

• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• Zur Vermeidung eines Kurzschlusses die Anschlußklemmen der NICHT VERWENDETEN Leitungen
mit Isolierklebeband umwickeln.

• Pour éviter les court-circuits, couvrir les bornes des fils
qui ne sont PAS UTILISÉS avec de la bande isolante.

• Om kortsluiting te voorkomen, moet u de
aansluitklemmen van ONGEBRUIKTE
gekleurde draden met isolatieband bedekken.

Connecting the leads / Anschließen der Leitungen / Raccordement des fils / Aansluiting van de gekleurde draden

Signal cord
(not supplied with this unit)

Einzelleitung (nicht mit diesem Gerät mitgeliefert)

Cordon de signal (non fourni avec cet appareil)

Signaalkabel (wordt niet bij dit apparaat geleverd)

Rear speakers

Hintere Lautsprecher

Enceintes arrière

Achterspeakers

KS-FX942R

To power aerial if any

Zur Motorantenne, sofern
vorhanden

Vers l’antenne automatique, s’il y
en a une

Naar de antenne (indien aanwezig)

Y-connector (not supplied with this unit)

Y-Anschluß (nicht mit diesem Gerät mitgeliefert)

Connecteur Y (non fourni avec cet appareil)

Y-connector (wordt niet bij dit apparaat geleverd)

Blue with white stripe

Blau mit weißem Streifen

Bleu avec bande blanche

Blauw met witte streep

Remote lead

Fernbedienungsleitung

Fil d’alimentation à distance

Afstandsbedieningsdraad

*2 :

Firmly attach the ground wire to the metallic
body or to the chassis of the car—to the place
not coated with paint (if coated with paint,
remove the paint before attaching the wire).
Failure to do so may cause damage to the unit.

*2 : Verbinden Sie den Erdungsleiter mit der

Karosserie oder dem Rahmen des Fahrzeugs.
Die Kntaktstelle darf nicht lackiert sein (sollte
die Kontaktstelle lackiert sein, entfernen Sie
den Lack der Kontaktstelle, bevor Sie den
Leiter befestigen). Wenn der Erdungsleiter
nicht ordnungsgemäß angeschlossen wird,
kann dieses Gerät beschädigt werden.

*2 : Attachez solidement le fil de mise à la masse

au châssis métallique de la voiture—à un
endroit qui n’est pas recouvert de peinture
(s’il est recouvert de peinture, enlevez
d’abord la peinture avant d’attacher le fil).
L’appareil peut être endommagé si cela n’est
pas fait correctement.

*2 : Bevestig de aardedraad goed met een metalen

onderdeel of het chassis van de auto—bevestig
op een niet-gelakt gedeelte (indien gelakt,
schuur dan af alvorens de draad te bevestigen).
Het toestel kan worden beschadigd indien de
aardedraad niet goed is aangesloten.

Sie können einen CD-Wechsler und/oder einen
DAB-Tuner (Tuner für digitalen Rundfunk) von JVC
anschließen.

• Weitere Informationen über den Anschluß können

Sie der Bedienungsanleitong entnehmen, die dem
jeweiligen Gerät beiliegt.

You can connect a JVC CD changer and/or a JVC
DAB (Digital Audio Broadcasting) tuner.

• For their connections, refer to the Instructions
supplied with them.

Vous pouvez connecter un changeur CD JVC et/ou
un tuner DAB (Digital Audio Broadcasting) JVC.

•

Pour leurs connexions, référez-vous aux “Manuel
d’instructions” qui les accompagnent.

Het is mogelijk een JVC CD-wisselaar en/of JVC
DAB-tuner (Digital Audio Broadcasting) aan te sluiten.

• Zie de Gebruiksaanwijzing van deze apparaten voor

meer informatie over het tot stand brengen van deze
aansluiting.

CD changer and DAB tuner / CD-Wechsler und DAB-Tuner / Changeur CD et tuner DAB / CD-wisselaar en DAB-tuner

Connecting cord supplied with your DAB tuner

Verbindungskabel, das zum Lieferumfang des DAB­Tuners gehört

Cordon de connexion fourni avec votre tuner DAB

Verbindingskabel die met de DAB-tuner wordt
meegeleverd

Connecting cord supplied with your CD changer

Verbindungskabel, das zum Lieferumfang des
CD-Wechsler gehört

Cordon de connexion fourni avec votre changeur CD

Verbindingskabel die met de CD-wisselaar wordt
meegeleverd

JVC CD changer

CD-Wechsler von JVC

Changeur CD JVC

JVC CD-wisselaar

JVC DAB tuner

DAB-Tuner von JVC

Tuner DAB JVC

JVC DAB-tuner

• You can connect both components in series as illustrated above.

• Es ist möglich, beide Komponenten in einer Serienschaltung entsprechend der obigen Darstellung
anzuschließen.

• Vous pouvez connecter les deux appareils en série comme montré ci-dessus.

• Beide apparaten zijn volgens bovenstaande illustratie in serie aan te sluiten.

or

oder

ou

of

JVC CD changer

CD-Wechsler von JVC

Changeur CD JVC

JVC CD-wisselaar

JVC DAB tuner

DAB-Tuner von JVC

Tuner DAB JVC

JVC DAB-tuner

Connecting cord supplied with your DAB tuner or CD changer

Verbindungskabel, das zum Lieferumfang des DAB-Tuners oder CD-Wechslers gehört

Cordon de connexion fourni avec votre tuner DAB ou changeur CD

Verbindingskabel die met de DAB-tuner of CD-wisselaar wordt meegeleverd

External Component / Externe Komponente / Appareil extérieur / Extern apparaat

Signal cord (not supplied with this unit)

Einzelleitung (nicht mit diesem Gerät mitgeliefert)

Cordon de signal (non fourni avec cet appareil)

Signaalkabel (wordt niet bij dit apparaat geleverd)

CD changer jack

Buchse für CD-Wechsler

Prise du changeur CD

Aansluiting voor CD-wisselaar

External component

Externe Komponente

Appareil extérieur

Extern apparaat

Line Input Adapter KS-U57 (not supplied with this unit)

Line-Eingangsadapter KS-U57 (nicht mit diesem Gerät mitgeliefert)

Adaptateur d’entrée de ligne KS-U57 (non fourni avec cet appareil)

Line Input Adapter KS-U57 (wordt niet bij dit apparaat geleverd)

CAUTION / VORSICHT / PRECAUTION / LET OP!:

• Before connecting the CD changer and/or the DAB tuner, make sure that the unit is turned off.

• Bevor Sie den CD-Wechsler und/oder den DAB-Tuner anschließen, vergewissern Sie sich, daß das
Gerät ausgeschaltet ist.

• Avant de connecter le changeur CD et/ou le tuner DAB, s’assurer que l’unité est éteinte.

• Zorg ervoor dat de apparaat is uitgeschakeld alvorens u de en/of DAB-tuner CD-wisselaar aansluit.

KS-FX942R

KS-FX942R

KS-FX942R

Front speakers

Vordere Lautsprecher

Enceintes avant

Voorspeakers

JVC Amplifier

JVC Verstärker

JVC Amplificateur

JVC Versterker

JVC Amplifier

JVC Verstärker

JVC Amplificateur

JVC Versterker

Front speakers

Vordere Lautsprecher

Enceintes avant

Voorspeakers

You can connect another power amplifier for front speakers.

Sie können einen anderen Leistungsverstärker für die vorderen Lautsprecher anschließen.

Vous pouvez connecter un autre amplificateur de puissance pour les enceintes avant.

U kunt nog een eindversterker voor de voorspeakers aansluiten.

Connecting to the steering wheel remote controller / Anschluß an die Lenkradfernbedienung / Connexion de la télécommande de volant /
Verbinden met de stuurwiel-afstandsbediening

If your car is equipped with the steering wheel remote controller, you can operate this receiver using the
controller. To do it, a JVC’s OE remote adapter (not supplied) which matches with your car is required.
Consult your JVC IN-CAR ENTERTAINMENT dealer for details.

Wenn Ihr Fahrzeug mit einer Lenkradferndienung ausgestattet ist, können Sie damit diesen Receiver
steuern. Hierfür ist ein für Ihr Fahrzeug passender Radio-Lenkrad-Fernbedienungsadaption von JVC (nicht
im Lieferumfang enthalten) erforderlich. Für weitere Einzelheiten wenden Sie sich an Ihren JVC
Autoradiohändler.

Si votre voiture est munie d’une télécommande de volant, vous pouvez commander cet autoradio en utilisant
la télécommande. Pour le faire, un adaptateur pour télécommande au volant (non fourni) correspondant à
votre voiture est nécessaire. Consultez votre revendeur d’autoradio JVC pour les détails.

Indien uw auto een stuurwiel-afstandsbediening heeft, kunt u deze receiver met die afstandsbediening bedienen.
Hiervoor heeft u echter een JVC adapter voor stuurwiel-afstandsbediening (niet bijgeleverd) nodig die geschikt is
voor uw auto. Raadpleeg uw JVC car audio dealer voor details.

KS-FX942R

Steering wheel remote input

Eingang für Lenkradfernbedienung

Entrée de la télécommande de volant

Ingang stuurwiel-afstandsbediening

OE remote adapter (not supplied)

Radio-Lenkrad-Fernbedienungsadaption
(nicht im Lieferumfang enthalten)

Adaptateur pour télécommande au volant (non fourni)

Adapter voor stuurwiel-afstandsbediening
(niet bijgeleverd)

Steering wheel remote controller (equipped in the car)

Lenkradfernbedienung (im Fahrzeug installiert)

Télécommande de volant (installée dans la voiture)

Stuurwiel-afstandsbediening (in de auto)

Solder the core wires to connect them
securely.

Die Kerndrähte anlöten, um sie fest
anzuschließen.

Souder les âmes des fils pour les raccorder
entre eux de façon sûre.

Soldeer de kerndraden zodat ze stevig vast
zitten.

L

R

L

R

L

R

L

R

See the INSTRUCTIONS (separate volume) for how to use the
external component with this unit.

Informationen zur Verwendung der externen Komponente mit
diesem Gerät finden Sie in den BEDIENUNGSANLEITUNG
(separates Dokument).

Référez-vous aux “MANUEL D’INSTRUCTIONS” (manuel séparé)
pour savoir comment utiliser l’appareil extérieur avec cet appareil.

Zie de GEBRUIKSAANWIJZING (apart boekje) voor details aangaande
het gebruik van het externe component met dit toestel.