JVC KD-SV3305, KD-SV3305S Instructions Manual
VCD/CD RECEIVER KD-SV3305
ENGLISH
ALAT PENERIMA VCD/CD KD-SV3305
For canceling the display demonstration, see page 7.
Untuk membatalkan tampilan demonstrasi, lihat halaman 7.
For installation and connections, refer to the separate manual.
Untuk instalasi dan penyambungan, lihat buku pedoman terpisah.
INDONESIA
INSTRUCTIONS
BUKU PETUNJUK
GET0471-007A
[UN]
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
ENGLISH
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
WARNINGS:
[European Union only]
How to reset your unit
• Your preset adjustments will also be erased.
How to forcibly eject a disc
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
To prevent accidents and damage
• DO NOT install any unit in locations where;
– it may obstruct the steering wheel and
gearshift lever operations.
– it may obstruct the operation of safety
devices such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
• If you need to operate the unit while
driving, be sure to look ahead carefully.
• The driver must not watch the monitor
while driving.
If the parking brake is not engaged,
“PARKING” flashes on the display, and
no playback picture will be shown on the
monitor.
– This warning appears only when the
parking brake wire is connected to the
parking brake system built in the car
(refer to the Installation/Connection
Manual).
2
The following marks are used to indicate...
: Built-in VCD/CD player operations.
: External CD changer operations.
: Indicator displayed for the
corresponding operation.
How to use the MODE button
If you press MODE, the unit goes into functions mode,
then the number buttons (except “1” and “4”) and
4 /¢ buttons work as different function
buttons.
Ex.: When number button 2 works as
MO (monaural) button.
To use these buttons for their original functions
again after pressing MODE, wait for 5 seconds
without pressing any of these buttons until the
functions mode is cleared or press MODE again.
Detaching the control panel
CONTENTS
Control panel .................................. 4
Remote controller —
Getting started ................................ 7
Basic operations ................................................... 7
Radio operations ............................. 8
Disc operations ................................ 9
Playing a disc in the unit ..................................... 9
Playing discs in the CD changer ........................... 10
Sound adjustments .......................... 14
General settings — PSM ................... 15
iPod/D. player operations ................. 17
Other external component
operations ................................... 19
Maintenance ................................... 19
More about this unit ........................ 20
Troubleshooting .............................. 23
Specifications .................................. 25
For safety...
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
RM-RK120 ............. 5
ENGLISH
Attaching the control panel
Temperature inside the car...
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
3
Control panel
Parts identification
ENGLISH
1 4 /¢ buttons
2 (standby/on attenuator) button
3 Remote sensor
Display window
DO NOT expose the remote sensor to strong light
(direct sunlight or artificial lighting).
4 Loading slot
5 Display window
6 0 (eject) button
7 EQ (equalizer) button
8 SRC (source) button
9 BAND button
6 (play/pause) button
p Control dial
q SEL (select) button
w MO (monaural) button
e SSM (Strong-station Sequential Memory) button
r Number buttons
t RPT (repeat) button
y RND (random) button
u MODE button
i DISP (display) button
o (control panel release) button
; Disc information indicators—TAG (ID3 Tag),
(folder), (track/file)
a Disc type indicators—WMA, MP3
s Playback source indicators—
CH: Lights up only when CD-CH is selected as the
playback source.
DISC: Lights up for the built-in CD player.
d Playback mode / item indicators— RND (random),
(disc), (folder), RPT (repeat)
f LOUD (loudness) indicator
g EQ (equalizer) indicator
h Sound mode (C-EQ: custom equalizer) indicators—
JAZZ, CLASSIC, HIP HOP, POPS, ROCK, USER
j Tr (track) indicator
k Source display / Volume level indicator
l Main display
/ Tuner reception indicators—ST (stereo),
MO (monaural)
4
Remote controller — RM-RK120
Installing the lithium coin battery
(CR2025)
Aim the remote controller directly at the remote
sensor on the unit. Make sure there is no obstacle
in between.
Warning:
• Do not install any battery other than CR2025 or
its equivalent; otherwise, it may explode.
• Do not leave the remote controller in a place
(such as dashboards) exposed to direct sunlight
for a long time; otherwise, it may explode.
• Store the battery in a place where children
cannot reach to avoid risk of accident.
• To prevent the battery from over-heating,
cracking, or starting a fire:
– Do not recharge, short, disassemble, heat the
battery, or dispose of it in a fire.
– Do not leave the battery with other metallic
materials.
– Do not poke the battery with tweezers or similar
tools.
– Wrap the battery with tape and insulate when
throwing away or saving it.
Main elements and features
ENGLISH
1 SOURCE button
• Selects the playback source.
2 (standby/on attenuator) button
• Turns the power on if pressed briefly or
attenuates the sound when the power is on.
• Turns the power off if pressed and held.
3 2 REV (reverse) / FWD (forward) 3 buttons
• Searches for stations if pressed briefly.
• Fast-forwards or reverses the track if pressed and
held.
• Changes the tracks if pressed briefly.
• While listening to an Apple iPod or a JVC
D. player (in menu selecting mode):
– Selects an item if pressed briefly. (Then, press
DOWN ∞ to confirm the selection.)
– Skips 10 items at a time if pressed and held.
Continued on the next page
5
4 VOL. + / – buttons
• Adjusts the volume level.
5 ENTER and number buttons
• Selects a track/file directly.
– Press the number button(s), then press ENTER.
– Not used for iPod/D. player operations.
ENGLISH
• Selects an item from the menu while playing
back a Video CD (VCD) in Playback Control (PBC)
function.
– Press the number button(s), then press ENTER.
• Selects the discs while operating the CD changer.
– To select disc number 1 – 6, press number
button 1 – 6 briefly.
– To select disc number 7 – 12, press and hold
number button 1 (7) – 6 (12).
6 EQ (equalizer) button
• Selects the sound mode (C-EQ: custom
equalizer).
7 BAND 6 button
• Changes the FM/AM bands.
• Stops disc playback temporarily. To resume
playback, press the button again.
– While playing a VCD, the playback scene at the
moment stops and remain still.
– Not used for CD changer, iPod, or D. player
operations.
8 5 UP / DOWN ∞ buttons
• Changes the preset stations.
• Changes the folder of the MP3/WMA discs if
pressed briefly.
• Changes the disc while operating the CD changer
if pressed and held.
• While listening to an iPod or a D. player:
– Pauses/stops or resumes playback with
DOWN ∞.
– Enters the main menu with 5 UP.
(Now 5 UP / DOWN ∞/2 REV / FWD 3 work
as the menu selecting buttons.)*
9 PBC (Playback Control) button
• Activates or deactivates the PBC function.
p RETURN button
• Returns to the previous menu while playing a
VCD in PBC function.
q OSD (On-Screen Display) button
• Turn on and off the OSD on the monitor.
w AUDIO button
• Selects the audio channel for VCD playback.
* 5 UP : Returns to the previous menu.
DOWN ∞ : Confirms the selection.
6
Getting started
Basic operations
~ Turn on the power.
To drop the volume in a
moment (ATT)
To restore the sound, press the
button again.
To turn off the power
ENGLISH
Ÿ
* You cannot select these sources if they are not
ready or not connected.
! For FM/AM tuner
⁄ Adjust the volume.
Volume level appears.
@ Adjust the sound as you want. (See
page 14.)
Basic settings
• See also “General settings — PSM” on pages 15 and
16.
1
2
1 Canceling the display demonstrations
Select “DEMO,” then “DEMO OFF.”
2 Setting the clock
Select “CLOCK H” (hour), then adjust the hour.
Select “CLOCK M” (minute), then adjust the
minute.
3 Finish the procedure.
To check the current clock time while the
power is turned off
Caution on volume setting:
Discs produce very little noise compared with other
sources. Lower the volume before playing a disc
to avoid damaging the speakers by the sudden
increase of the output level.
7
Radio operations
~
ENGLISH
When an FM stereo broadcast is hard to
receive
Ÿ
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
! Start searching for a station.
When a station is received, searching stops.
To stop searching, press the same button
again.
To tune in to a station manually
In step ! above...
1
2 Select a desired station frequency.
Lights up when monaural mode is activated.
Reception improves, but stereo effect will be lost.
To restore the stereo effect, repeat the same
procedure. “MONO OFF” appears and the MO indicator
goes off.
Storing stations in memory
You can preset six stations for each band.
FM station automatic presetting —
SSM (Strong-station Sequential
Memory)
1 Select the FM band (FM1 – FM3) you want to
store into.
2
3
“SSM” flashes, then disappears when automatic
presetting is over.
Local FM stations with the strongest signals are
searched and stored automatically in the FM band.
8
Manual presetting
Ex.: Storing FM station of 92.5 MHz into preset number
4 of the FM1 band.
1
2
3
Preset number flashes for a while.
Listening to a preset station
1
2 Select the preset station (1 – 6) you want.
To check the other information while
listening to the radio
Clock Ô Frequency
Disc operations
Playing a disc in the unit
All tracks will be played repeatedly until you change the
source or eject the disc.
• If a disc menu appears on the monitor while playing a
VCD with PBC, see page 11.
Before performing any operations, make sure the
following....
• Turn on the monitor and select the appropriate
monitor input before playing a VCD.
• If you turn on the monitor, you can also control the
MP3/WMA playback by referring to the monitor
screen (see page 12).
• Select the video system suitable for your monitor (see
page 16).
To stop play temporarily
To resume playback, press the
button again.
To stop play and eject the
disc
ENGLISH
Continued on the next page
9
Playing discs in the CD changer
All discs in the magazine will be played repeatedly until
you change the source.
• Ejecting the magazine will also stop playing.
ENGLISH
~
* If you have changed the external input setting
to “EXT IN” (see page 16), you cannot select the
CD changer.
Ÿ Select a disc.
For disc number from 01 – 06:
To fast-forward or reverse the track
To go to the next or previous tracks
To go to the next or previous folders (only for
MP3 or WMA discs)
For MP3 discs:
For WMA discs:
For disc number from 07 – 12:
About MP3 and WMA discs
MP3 and WMA “tracks” (words “file” and “track” are
used interchangeably) are recorded in “folders.”
About the CD changer
It is recommended to use a JVC MP3-compatible CD
changer with your unit.
• You can also connect MP3-incompatible CD changers.
However, these units are not compatible with MP3
discs.
• You cannot use the CH-X99, CH-X100, and KD-MK
series CD changers with this unit.
• You cannot control and play any WMA or VCD disc in
the CD changer.
• Disc text information recorded in the CD Text can be
displayed when a JVC CD Text compatible CD changer
is connected.
• For connection, see Installation/Connection Manual
(separate volume).
1
2
To locate a particular track (for CD or VCD
with PBC set to “PBC OFF”) or folder (for MP3
or WMA discs) directly
To select a number from 01 – 06:
To select a number from 07 – 12:
• To use direct folder access on MP3/WMA discs, it
is required that folders are assigned with 2-digit
numbers at the beginning of their folder names—
01, 02, 03, and so on.
To select a particular track in a folder
(for MP3 or WMA discs):
10
Playback Control (PBC) operations
On-Screen (OSD) information
This operation is only possible when using the
remote controller.
1 While playing a VCD....
PBC ON Ô PBC OFF
PBC ON : A menu appears on the monitor.
PBC OFF : Cancels.
• A menu may be a list of items, submenus, or
some moving pictures.
2 Select the item you want.
• To select an item from the submenus, repeat this
step.
The selected item starts playback automatically.
This operation is only possible when using the
remote controller.
You can check the track number and elapsed playing
time if the monitor is turned on.
While playing a disc....
• To turn off the On-Screen Display,
press the button again.
Current/total track number
Elapsed playing time
Selecting the audio channel
This operation is only possible when using the
remote controller.
You can select the audio channel to play. (This is
convenient when playing a Karaoke VCD.)
ENGLISH
To correct a mis-entry and to return to the
previous menu
STEREO : To listen to normal stereo (left/right)
playback.
MONO L : To listen to the L (left) audio channel.
MONO R : To listen to the R (right) audio channel.
• The audio channel is automatically set to “STEREO”
when you change the disc or source.
11
MP3/WMA control screen operations
You can also control the playback of an MP3/WMA disc
ENGLISH
by referring to the monitor.
• The control screen automatically appears on the
monitor when you insert an MP3/WMA disc.
1 Artiste name* (only for MP3 discs)
• The artiste name will scroll on the monitor if it
cannot be shown at a time.
2 Operation mode—PLAY, PAUSE, FF (fast-forward),
FR (fast-reverse), SELECT (selected track number),
REPEAT TRACK, REPEAT FOLDER, REPEAT OFF,
RANDOM FOLDER, RANDOM DISC, RANDOM OFF
• Operation mode appears for a while on the
monitor.
3 Folder name*
4 Track title* (only for MP3 discs)
• The track title will scroll on the monitor if it
cannot be shown at a time.
5 Highlighted bar for the current file name*
6 OSD indication—Current/total track number,
Elapsed playing time
• Appears only if you turn on the OSD (see page
11).
7 Current list/total list number
8 Track list
• The monitor can show 12 tracks at a time and a
maximum of 239 tracks for a disc.
* Some symbols will not be shown (and will be
substituted or blanked) on the control screen.
To select a folder
To select a track
• Pressing these buttons repeatedly can also select
tracks from the previous/next folders.
• See also page 10 for using the buttons on the control
panel to select a folder or track.
Selecting the playback modes
You can use only one of the following playback modes
at a time.
• For VCD: While PBC (see page 11) is not in use.
1
2 Select your desired playback mode.
7 Repeat play
Mode Plays repeatedly
TRK RPT : The current track.
FLDR RPT*1 : All tracks of the current folder.
DISC RPT*2 : All tracks of the current disc.
RPT OFF : Cancels.
12
7 Random play
Mode Plays at random
FLDR RND*
1
: All tracks of the current folder,
then tracks of the next folder and
so on.
DISC RND : All tracks of the current disc.
MAG RND*2 : All tracks of the inserted discs.
RND OFF : Cancels.
1
Only while playing an MP3 or a WMA disc.
*
*2 Only while playing discs in the CD changer.
Other main functions
Changing the display information
• For MP3 disc : When “TAG DISP” is set to “TAG OFF”
• For WMA disc :
: Clock with the current track number
: Elapsed playing time with the current track
number
1
*
If the current disc is an audio CD or a VCD, “NO NAME”
appears.
2
Only for the built-in CD player.
*
*3 If an MP3 file does not have Tag information, folder
name and file name appear. In this case, the TAG
indicator will not light up.
Prohibiting disc ejection
You can lock a disc in the loading slot.
ENGLISH
While playing an audio CD, a CD Text, or a VCD
with PBC set to “PBC OFF” (see page 11)
While playing an MP3 or a WMA*2 disc
• Only for MP3 disc : When “TAG DISP” is set to
“TAG ON” (see page 16)
To cancel the prohibition, repeat the same
procedure.
13
Sound adjustments
You can select a preset sound mode suitable to the
music genre (C-EQ: custom equalizer).
ENGLISH
Adjusting the sound
You can adjust the sound characteristics to your
preference.
1
Preset values
Indication (For)
USER
(Flat sound)
ROCK
(Rock or disco music)
CLASSIC
(Classical music)
POPS
(Light music)
HIP HOP
(Funk or rap music)
JAZZ
(Jazz music)
BAS
TRE
LOUD
(bass)
(treble)
(loudness)
00 00 OFF
+03 +01 ON
+01 –02 OFF
+04 +01 OFF
+02 00 ON
+02 +03 OFF
2
Indication [Range]
1
(bass)
BAS*
Adjust the bass. [–06 to +06]
1
TRE*
(treble)
Adjust the treble. [–06 to +06]
2
(fader)
FAD*
Adjust the front and rear speaker balance. [R06 to F06]
BAL (balance)
Adjust the left and right speaker balance.
[L06 to R06]
1
(loudness)
LOUD*
Boost low and high frequencies to produce a wellbalanced sound at low volume level.
[LOUD ON or LOUD OFF]
VOL (volume)
Adjust the volume. [00 to 30 or 50*
1
*
When you adjust the bass, treble, or loudness, the
adjustment you have made is stored for the currently
selected sound mode (C-EQ) including “USER.”
*2 If you are using a two-speaker system, set the fader
level to “00.”
*3 Depending on the amplifier gain control setting. (See
page 16 for details.)
3
]
14
General settings — PSM
You can change PSM (Preferred Setting Mode) items listed in the table that follows.
1
4 Repeat steps 2 and 3 to adjust other PSM
items if necessary.
ENGLISH
2 Select a PSM item.
3 Adjust the PSM item selected.
Indications Item
( : Initial)
DEMO
Display demonstration
CLOCK H
Hour adjustment
CLOCK M
Minute adjustment
DIMMER
Dimmer
TEL
Telephone muting
• DEMO ON
• DEMO OFF
1 – 12 [Initial: 1 (1:00)], [7]
00 – 59 [Initial: 00 (1:00)], [7]
• ON
• OFF
• MUTING 1/
MUTING 2:
• OFF
5 Finish the procedure.
Setting, [reference page]
: Display demonstration will be activated automatically if no
operation is done for about 20 seconds, [7].
: Cancels.
: Dims the display illumination of this unit.
: Cancels.
: Select either one which mutes the sounds while using a cellular
phone.
: Cancels.
Continued on the next page
15
Loading...