JVC KDS-577 Service manual

SERVICE MANUAL

CD RECEIVER

KD-S577

DIGITAL AUDIO

Contents

Safety precaution Preventing static electricity Location of main parts Disassembly method Adjustment method Flow of functional operation until TOC read Maintenance of laser pickup Replacement of laser pickup Description of major ICs

COMPACT

Area Suffix

UR ---- Brazil

1-2 1-3 1-4 1-5 1-10 1-11 1-13 1-13 1-14

No.49629

Apr. 2001

KD-S577

Safety precaution

Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.

Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.

1-2

KD-S577

Preventing static electricity

1.Grounding to prevent damage by static electricity

Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.

2.About the earth processing for the destruction prevention by static electricity

Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players. Be careful to use proper grounding in the area where repairs are being performed.

2-1 Ground the workbench

Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it.

2-2 Ground yourself

Use an anti-static wrist strap to release any static electricity built up in your body.

(caption) Anti-static wrist strap

Conductive material (conductive sheet) or iron plate

3. Handling the optical pickup

1. In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.)

2. Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily destroy the laser diode.

4.Handling the traverse unit (optical pickup)

1. Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.

2. Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector.

3. Handle the flexible cable carefully as it may break when subjected to strong force.

4. It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it

CD mechanism ass’y

Damper bracket

Attention when traverse unit is decomposed

*Please refer to "Disassembly method" in the text for pick-up and how to detach the substrate.

1.Solder is put up before the card wire is removed from connector on the CD substrate as shown in Figure. (When the wire is removed without putting up solder, the CD pick-up assembly might destroy.)

2.Please remove solder after connecting the card wire with when you install picking up in the substrate.

Front bracket

Feed motor ass’y

FD screw

CD mechanism control board

Soldering

FD gear

Pickup unit

1-3

KD-S577

Location of main parts

Control unit

Display

LED & key control board

Main uni

CD mechanism

Main board

Mechanism relay board

Power IC

ISO connector

Main board

Loading motor

Antenna jack

Tuner

pack

Connector to controller

1-4

Damper

Spindle motor

Optical pick up unit

Feed motor

Damper

Disassembly method

Removing the front panel unit

(See Fig.1)

1. Press the release switch and remove the front panel unit in the direction of the arrow.

KD-S577

Release switch

Fig.1

Removing the front chassis (See Fig.2)

1. Insert a screwdriver to the two joints a on the side

of the front chassis and two joints b on the right side, then detach the front chassis toward the front side.

Removing the heat sink (See Fig.3)

1. Remove the three screws A attaching the heat sink on the left side of the body, and remove the heat sink.

Front chassis

Fig.2

Heat sink

Fig. 3

Removing the bottom cover (See Fig.4)

1.2.Turn the body upside down.

Insert a screwdriver to the two joints c and two joints d on both sides of the body and the joint e on the back of the body, then detach the bottom cover from the body.

Regulator board

Fig. 4

1-5

KD-S577

Removing the main board

(See Fig.5 and 6)

Remove the front chassis.

Remove the bottom cover.

Remove the two screws B attaching the main board assembly on the bottom of the body.

Remove the three screws C attaching the main board assembly on the back of the body.

Disconnect connector CN501 on the main board assembly from the CD mechanism assembly.

Main board

CN501

Fig.5

Fig. 6

Removing the CD mechanism assembly

(See Fig.7)

Remove the front chassis.

Remove the bottom cover.

Remove the main board assembly.

Remove the three screws D attaching the CD mechanism assembly from the top cover.

Removing the LCD & key control board

(See Fig.8 and 9)

Remove the front chassis.

Remove the four screws E attaching the rear cover on the back of the front panel unit.

Remove the LCD & key control board from the front panel unit.

CD mechanism assembly

Top cover

Fig. 7

Fig. 8

LCD & key control board

1-6

Fig. 9

KD-S577

Removing the CD mechanism control board (See Fig.1 and 2)

Unsolder the part a and b on the CD mechanism control board.

Remove the stator fixing the CD mechanism control board and the damper bracket (To remove the stator smoothly, pick up the center part).

Remove the screw A attaching the CD mechanism control board.

Remove the CD mechanism control board in the direction of the arrow while releasing it from the two damper bracket slots d and the front bracket slot e.

Disconnect the flexible wire from connector on the pickup unit.

ATTENTION:

Turn the FD gear in the direction of the arrow to move the entire pickup unit to the appropriate position where the flexible wire of the CD mechanism unit can be disconnected easily.

(Refer to Fig.2)

CD mechanism assembly

Front bracket

Pickup unit

Damper bracket

Fig.1

Flexible wire

CD mechanism control board

Shift the lock

Removing the loading motor

(See Fig.3 to 5)

Prior to performing the following procedure, remove the CD mechanism control board.

Remove the two springs f attaching the CD mechanism assembly and the front bracket.

Remove the two screws B and the front bracket while pulling the flame outward.

Remove the belt and the screw C from the loading motor.

Loading motor

FD gear

Loading motor

Pull outward

Fig.2

CD mechanism control board

Front bracket

Fig.3

Front bracket

Pull outward

Fig.5

Belt

Flame

Fig.4

1-7

KD-S577

Removing the CD mechanism assembly

(See Fig.1, 6 to 9)

Prior to performing the following procedure, remove the CD mechanism control board and the front bracket (loading motor).

Remove the three screws D and the damper bracket.

Raise the both sides fix arms and move the fix plates in the direction of the arrow to place the four shafts g as shown in Fig.8 and 9.

Remove the CD mechanism assembly and the two springs h attaching the flame.

Remove the two screws E and both sides rear damper brackets from the dampers. Detach the CD mechanism assembly from the left side to the right side.

ATTENTION:

The CD mechanism assembly can be removed if only the rear damper bracket on the left side is removed.

CD mechanism

Front bracket

CD mechanism

Flame

assembly

Damper bracket

Fig.1

Fig.6

Damper bracket

CD mechanism control board

Fix plate (L)

Fix arm (R)

Fig.7

Rear damper bracket

Fig.8

Rear damper bracket

Fix plate(R)

Fix arm (L)

Damper

1-8

Damper

Fig.9

KD-S577

Removing the feed motor assembly

(See Fig.10)

Prior to performing the following procedure, remove the CD mechanism control board, the front bracket (loading motor) and the CD mechanism assembly.

Remove the two screws F and the feed motor assembly.

Removing the pickup unit

(See Fig.10 and 11)

Prior to performing the following procedure, remove the CD mechanism control board, the front bracket (loading motor), the CD mechanism assembly and the feed motor assembly.

Detach the FD gear part of the pickup unit upward. Then remove the pickup unit while pulling out the part i of the FD screw.

Feed motor assembly

FD gear

Nut push spring plate

FD screw

Pickup unit

Fig.10

Part i

Part j

Pickup unit

Pickup mount nut

Pickup unit

ATTENTION:

Remove the screw G attaching the nut push spring plate and the pickup mount nut from the pickup unit. Pull out the FD screw.

When reattaching the pickuap unit, reattach the part j of the pickup unit, then the part i of the FD screw.

Removing the spindle motor

(See Fig.12 and 13)

Prior to performing the following procedure, remove the CD mechanism control board, the front bracket (loading motor), the CD mechanism assembly and the feed motor assembly.

Turn up the CD mechanism assembly and remove the two springs k on both sides of the clamper arms. Open the clamper arm upward.

Turn the turn table, and remove the two screws H and the spindle motor.

FD screw

Spindle motor

Fig.11

Fig.12

Fig.13

1-9

KD-S577

Adjustment method

Test instruments required for adjustment

1. Digital oscilloscope (100MHz)

2. AM Standard signal generator

3. FM Standard signal generator

4. Stereo modulator

5. Electric voltmeter

6. Digital tester

7. Tracking offset meter

8. Test Disc JVC :CTS-1000

9. Extension cable for check EXTGS004-26P 1

Standard measuring conditions Power supply voltage DC14.4V(10.5~16V) Load impedance 4 (2 Speakers connection) Lineout impedance 20K Output Level Line out 2.0V (Vol. MAX)

How to connect the extension cable for adjusting

Standard volume position Balance and Bass &Treble volume : lndication"0" Loudness : OFF BBE : OFF

Frequency Band FM 87.5MHz ~ 108.0MHz MW 531kHz ~ 1602 kHz

Dummy load Exclusive dummy load should be used for AM,and FM. For FM dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered since direct reading of figures are applied in this working standard.

The cardboard is cut in a suitable size. uses for the insulation stand of mechanism.

EXTGS004-26P

1-10

Flow of functional operation until TOC read

Power ON

• When the pickup correctly moves to the inner area of the disc

Set Function to CD

KD-S577

• When the laser diode correctly emits

Microprocessor

commands

FMO TC9462 "53"

FEED MOTOR +TERMINAL

TERMINAL

IC581 "5" REST SW

• When correctly focused

Focus Servo Loop ON

Disc inserted

Pickup feed to the inner area

Laser emitted

Focus search

Disc rotates

RF signal eye-pattern remains closed

Tracking loop closed

RF signal eye-pattern opens

TOC readout

YES

Microprocessor

commands

"No disc"

display

• When the disc correctly rotates

Microprocessor commands

Spindle motor (-) IC581 "7"

AccelerationAcceleration

0.5 Sec

Rough

Servo

0.5 Sec

Servo CLV

Jump to the first track

Play

Tracking Servo Loop ON

• RF signal

Rough Servo Mode

CLV Servo Mode (ProgramArea)

CLV Servo Mode (Lead-In Area; Digital: 0)

1-11

KD-S577

Feed Section

Is the voltage output at

IC521 pin "53" 5V or 0V?

Is 4V present at both

sides of the feed motor?

YES

Is the wiring for IC521

(90) ~ (100) correct?

Is 6V or 2V present at

IC581 "5" and "6"?

YES

Is 5V present at IC581

pin "11"?

YES

Check the vicinity of

IC521.

Check the feed motor

connection wiring.

NONO

Check CD 9V

and 5V.

Check the feed motor.

Focus Section

When the lens is

moving:

Does the S-search

waveform appear at

IC581 pins "17" and "18"?

Spindle Section

Is the disk rotated?

YES

Does the RF signal

appear at TP1?

YES

Check IC581.

Check the circuits in

the vicinity of IC581

pins "15" ~ "18".

Check the pickup and

its connections.

Is 4V present at IC581

pins "7" and "8" ?

YES

Check the spindle motor

and its wiring.

YES

NO NO

Is 4V present at IC521

pin "55" ?

YES

Check the vicinity of

IC581.

Check IC501 and

IC521.

Is the RF waveform at TP1

distorted?

Proceed to the Tracking

section

Tracking Section

When the disc is rotated

Is the tracking error signal

1-12

YES

at first:

Approx. 1.2 V

output at IC501 "12"?

YES

Check IC521.

Check the circuits in the

vicinity of IC501 "19" ~

"24" or the pickup

Check the circuit in the

vicinity of IC501 pins

"2" ~ "12".

YESYES

Check the pickup and

its connections.

Maintenance of laser pickup

(1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens with a alcohol soaked cotton swab.

(2) Life of the laser diode When the life of the laser diode has expired, the following symptoms will appear. (1) The level of RF output (EFM output:ampli tude of eye pattern) will be low.

KD-S577

Is RF output

1.0 0.35Vp-p?

YES

O.K

(3) Semi-fixed resistor on the APC PC board The semi-fixed resistor on the APC printed circuit board which is attached to the pickup is used to adjust the laser power.Since this adjustment should be performed to match the characteristics of the whole optical block, do not touch the semi-fixed resistor. If the laser power is lower than the specified value,the laser diode is almost worn out, and the laser pickup should be replaced. If the semi-fixed resistor is adjusted while the pickup is functioning normally,the laser pickup may be damaged due to excessive current.

Replace it.

Replacement of laser pickup

Turn off the power switch and,disconnect the power cord from the ac outlet.

Replace the pickup with a normal one.(Refer to "Pickup Removal" on the previous page)

Plug the power cord in,and turn the power on. At this time,check that the laser emits for about 3seconds and the objective lens moves up and down. Note: Do not observe the laser beam directly.

Play a disc.

Check the eye-pattern at TP1.

Finish.

1-13

+ 29 hidden pages