KD-A5 B/E
Pag | je |
---|---|
Specifications | 2 |
Features | 3 |
Controls and Connections | 3 |
Main Parts Location | 4 |
Maintenance | 4 |
Removal of the Main Parts | 5 |
Main Adjustments | 7 |
Block Diagram 1 | 2 |
Integrant Circuit 1 | 4 |
Standard Schematic Diagram (Amplifier Circuit) 1 | 5 |
" " (Mecha. Control Circuit) . 1 | 6 |
Wiring Connection (1) 1 | 7 |
" " (2) | 8 |
Page |
---|
Enclosure Assembly and Electrical Parts List 18 |
Enclosure Assembly and Electrical Parts |
Mechanical Component Parts |
Mechanical Component Parts List |
Main Amp. P.W. Board Parts List |
Main Amp. P.W. Board Parts |
Control P.W. Board Parts 28 |
Control P.W. Board Parts List |
Other P.W. Board Parts 34 |
Other P.W. Board Parts List |
Packing, Packing Material Parts List, |
Accessories |
Туре | : Component stereo cassette deck | Tape speed | : 4.76 cm/sec ± 2% |
---|---|---|---|
Power requiremen | t : AC 120 V, 60 Hz (KD-A5C/J) | Recording time | : 2 x 30 minutes with C-60 cassette |
AC 240/220/120 V, 50/60 Hz | Fast forward time | : 85 sec with C-60 cassette | |
(KD-A5A/B/E) | Playback torque | : 40–70 gr./cm | |
AC 240/220/120/100 V, 50/60 Hz | Fast-forward or | ||
(KD-A5U) | Rewind torque | : More than 70 gr./cm | |
Power consumptio | n: 29 W | Bias frequency | : 85 kHz |
Motors | : FG servo DC motor x 1 Capstan | Input terminals | : MIC jack x 2 |
DC motor x 1 Reel | Max. sensitivity: 0.2 mV (-72 dBs) | ||
Heads | : (For Metal tape) | Matching impedance: 600 Ω-10 kΩ | |
Recording/Playback; Sen-Alloy head | LINE IN jack x 2 | ||
Erasure; 2 gap, Sen-Alloy head | Min. input level: 78 mV (–20 dBs) | ||
Frequency respons | e: | Input impedance: 100 kΩ | |
0.)(1) | Metal tape; 30–12500 Hz 👝 👝 | Output terminals | : LINE OUT jack x 2 |
0.00 | CrO 2 tape; 30– 8000 Hz (Typical) | · | Output level; 0–0.3 V |
Metal tape; 20–18000 Hz (Nominal) | Output impedance; 3–6 kΩ | ||
30–16000 Hz (Typical) | PHONES x 1 | ||
CrO2 tape; 20-18000 Hz (Nominal) | Output level; 0.3 mV | ||
20 VU | 30-16000 Hz (Typical) | Matching impedance: 8 Ω – 1 kΩ | |
SF tape; 20–17000 Hz (Nominal) | DIN socket | : Min. input level 0.1 mV/kΩ | |
30–15000 Hz (Typical) | (KD-A5B/E) | Input impedance 3kΩ | |
Surpasses DIN 45 500 | ( | Output level 0–300 mV | |
Signal-to-Noise rat | io: 60 dB (from peak level, weighted, | Output impedance: 5kΩ | |
metal tape). The S/N is improved by | Matching impedance; 50k Ω or more | ||
5 dB at 1 kHz and by 10 dB above | Semiconductors | : 10 ICs (1 hall element), 58 transistors. | |
5 kHz with ANRS on. | (KD-A5B/E: 62) | ||
Effect of Super Al | NRS: (normal tape) | 40 diodes (4 zener diodes) [KD-A5B/E; | |
Improvement of | S/N: the same as with ANRS | 41 (5 Zener diodes)] and 9 LEDs | |
Improvement of | fre- | Dimensions | : Width; 420 mm (16-1/2") |
quency respons | e: 0 VU recording; 6 dB at 10 kHz | Height; 120 mm (4-3/4'') | |
+5 VU recording; 12 dB at 10 kHz | Depth; 300 mm (11-7/8'') | ||
Improvement of | Weight | : 6.8 kg (14.96 lbs) | |
distortion | : 0 VU recording; 3% less at 10 kHz | ||
+5 VU recording; 3% or less at 10 kHz | * Metal tape – 3M | SCOTCH METAFINE or equivalent | |
Crosstalk | : 65 dB | Chrome tape – T | FDK SA or equivalent |
Harmonic distortion | : K3; 0.4%, THD; 10% | SF tape – MAXI | ELL-UD or equivalent |
(with Metal tape at 1 kHz) | Design and specificat | ions are subject to change without notice. | |
Wow and flutter : | 0.04% (WRMS) | ||
0.14% (DIN 45 500) |
No. 4182
Mechanical parts are the same as model KD-A6. See the service manual of KD-A6A/B/C/E/J/U (No. 4179 – page 4).
To get long, trouble-free service, maintenance is important. Do not forget cleaning and demagnetizing.
After long, the heads and tape part – capstan, pinch roller, etc. – will become dirty with dust or magnetize particles. Dirty heads cause imperfect erasing or hogj frequency drop-off. A dirty capstan and pinch roller will cause unstable tape speed, leading to increased wow and flutter. Always keep them clean by following the procedure below.
(It is effective to moisten the cotton with alcohol.)
Perform the cleaning in the same manner as for the heads.
* Do not use any cleaner besides alcohol or a specifically prepared tape head cleaning solution.
Wipe the cabinet and panel clean with a soft cloth dipped in a neutral cleaner. Do not use thinner, benzine, alcohol or other strong slovents, as these will cause damage to the surface finish of the cabinet and panel.
The heads are made from a material resistant to magnetization, but after long use they may become magnetized. A magnet brough into their vicinity can magnetize the heads, causing excess noise. If noise seems to have increased, demagnetize the heads with a head demagnetizer through the following procedure.
Feed one or two drops of machine oil to the rewind roller shaft, pinch roller shaft and magnet pulley shaft once or twice a year under normal conditions of use.
Avoid oiling them excessively, or rotation may become irregular because of oil splashes.
This cassette deck which features a compact design and high parts which are closely arranged. Take special care when servi
When adjusting or replacing REC/PB or Erase head ......
When assembling the control switch ass'y to the front panel, do in the order of the numbers as below so as not to damage the front panel.
(Bottom view)
et design and high performance uses miniature-sized ial care when servicing it.
Remove the 4 screws ④ on the bottom side fastening the control P.W. board ass'y to the amp. chassis.
No. 4182
Remote ba
When replacing the motor, check the following items. 1) Is the motor placed in the correct position?
Power switch
Bracket
-6)
[1] Equipment and measuring instruments used for adjustment
100 Ω (for measurement of the bias current) 600 Ω (for attenuator matching)
Checking method: Record a 400 Hz or 1 kHz signal with 0 VU + 20 dB. Erase the recording. Check if the erasing is satisfactorily performed.
4) After adjustment, apply screw bond on the adjusting screw to prevent its loosening.
ltem | Adjustment |
Adjusting
point |
Standard
value |
Remarks |
---|---|---|---|---|
Adjusting record/
playback head position |
|
Screw A | Maximum |
|
(Adjust the mechanism or confirm that it is in normal operating condition prior to the adjustment of the electrical circuit.)
ltem | Adjustment |
Adjusting
point |
Standard
value |
Remarks |
---|---|---|---|---|
Adjusting erase
head height |
Employ a special cassette (C-120) from
which parts of the casing, where the erase head, record/playback head and capstan engage, has been cut away. Perform tape transport with the cassette tape. Adjust |
Screw C |
|
|
the screw C until the tape runs in the center
of the erase head tape guide. (See "Troubleshooting hints" aforesaid.) |
Be sure to perform this adjust-
ment after replacing the erase head. |
|||
Correcting Discorrecting
Tape guide Tape |
||||
Adjusting motor
speed |
Connect a speed meter to the LINE OUT
terminals. Play back the VTT-656 test tape. Adjust the semi-fixed resistor in the motor until the reading of the speed meter is 3000 Hz. |
Semi-fixed
resistor in the motor case |
3000 Hz |
If the speed meter functions as
a wow and flutter meter, also, connect the deck to the INPUT terminals of the meter. |
Checking play-
back torque |
Employ a torque testing cassette tape for
the checking, or remove the cassette cover and use a torque gauge. |
40—70
gr-cm |
If the standard torque is not
obtained, replace the take-up disc assembly. |
|
Checking fast
forward torque |
Measure the torque in the fast forward mode
in the same manner as in the above. |
More than
70 gr-cm |
|
|
Checking rewind
torque |
Measure the torque in the rewind mode in the same manner as in the above. |
More than
70 gr-cm |
If the standard torque is not ob-
tained, clean the capstan belt, idler, motor pulley, flywheel circumference, rewinding idler circumference, left reel disc cir- cumference, etc. |
|
Adjusting the
auto-stop mechanism |
Perform the adjustment with the 2-screws securing the solenoid. | |||
Checking wow
and flutter |
Connect a wow and flutter meter to the
LINE OUT terminals. Play back the VTT-656 test tape. Check to see if the reading of the meter is within 0.04% (WRMS). |
If the reading becomes moving
value even if conforming to the standard, a re-claim may be raised. Repairs are necessary. |
Oil employed – Torque grease specified by JVC (KANTO KASEI GP-608) Applying method – Apply in both concaved sections as shown in the figure.
If wow and flutter increase, check the following points. If there is defect in revolving parts, the wow and flutter generated will increase in proportion to the number of revolutions.
Play a 3000 Hz test tape, and defective part can be detected from the sound.
Section | Trouble | Repair , | ||||
---|---|---|---|---|---|---|
Capstan and flywheel |
Capstan shaft has excessive run-out
Flywheel turns heavily. (shaft seisure, thrust play, etc.) |
Replace flywheel.
Clean the capstan shaft and the groove in the fly wheel. Apply oil to the metal position. Replace the capstan assembly. |
||||
Pinch roller |
Rough rotation (Deformation scratches,
or dust) The angular position of the pinch roller is not correct. The pinch roller pressure is not correct. |
Replace pinch roller, or pinch roller spring.
Clean the pinch roller or apply oil to the rotary shaft. Adjust the pinch roller so that it is parallel with the capstan shaft. Replace the pinch roller spring. |
||||
Belt |
Belt has undue run-out.
Belt is dirty or slippery. |
Clean the belt.
Replace the belt. |
||||
Back tension | Back tension is irregular, or back tension is too strong. | Replace back tension spring (under supply disc). | ||||
Motor |
Motor shaft has undue run-out.
Motor pulley is oily and dusty. |
Replace motor.
Clean motor pulley. |
Main Amp. P.W. Board
In the steps marked by an asterisk (*), adjustment should be performed, however, only checking is sufficient with steps other than those.
Adjustment should be performed in the order of steps 1, 2, 3 .....
Step | Item | Adjustment |
Adjusting
point |
Standard
value |
Remarks |
---|---|---|---|---|---|
1* |
Playback
frequency response |
|
L
2
(M
2
).
6.3 kHz, response. again. If 10 kHz adjust VF receptacle receptacle |
And ther
IO kHz signa If not flat, a signal inc R101, 201 tab for adju wire. |
h, check 333 kHz,
als to become flat djust VR101, 201 rese and can not or not select the istment, open the |
2* |
Adjusting
playback level |
|
VR102,
202 |
—8 dBs
(0.3 V) |
|
3* |
Adjusting
VU meter sensitivity |
|
VR106,
206 |
0 VU | Perform the adjustment when the parts are replaced. |
4* |
Checking
record/ playback frequency response |
Record 1 kHz, 50 Hz and 12.5 kHz signals
at an input level of 0 VU –20 dB. Play back the tape. Check to see that the 50 Hz and 12.5 kHz signal output deviations fall within the standard range, using the 1 kHz signal out- put as a reference. (It is basically desirable that the 1 kHz, 50 Hz and 12.5 kHz signal outputs are the same. |
For normal
tape: VR107, 207 For chrome tape: VR109, 209 For Metal |
Reference
frequency; 1 kHz 0 ± 3 dB at 50 Hz 0 ± 3 dB at 12.5 kH |
This checking should be performed
for normal and chrome tapes and for both right and left channels. |
5* |
Checking
recording bias cur- rent |
Record 1 kHz, 50 Hz and 12.5 kHz signals
at an input level of 0 VU –20 dB. Play back the tape. Adjust VR107 and VR207 (for a normal tape), VR109 and VR209 (for a chrome tape), VR108 and VR208 (for a metal tape) until the indicated deviation of the 10 kHz signal output from the 1 kHz signal output becomes 0. As no bias current at REC-PAUSE mode, must check recording bias current at REC- PLAY mode. |
tape:
VR108, 208 |
Output
deviation: 0 (gp) escodser H 50H |
|
Step | Item | Adjustment |
Adjusting
point |
Standard
value |
Remarks |
---|---|---|---|---|---|
|
Reference
value With nor- mal tape; 30 mV With chrome tape; 42 mV With Metal tape: 65 mV |
|
|||
6 |
Adjusting
recording level |
|
VR104,
204 |
0 VU |
The level difference between left and
right channels for normal tape, chrome tape and metal tape should be less than 1 dB (1 VU). Perform the adjustment using a normal tape, level difference between recording and playback for CrO 2 and metal tapes should be less than 1.5 dB, and that between left and right channels should also be less than 1 dB. |
7 |
Checking
record/ playback signal dis- tortion |
|
Normal
tape; Less than 1.2 % |
Be sure to perform this adjustment fol-
lowing bias current and recording level adjustments. |
|
8 |
Checking
signal to noise ratio in record- ing/play- back |
|
Normal
tape; More than 42 dB Chrome tape; More than 42 dB |
Apply an output (-72 dBs) to the MIC
terminals with the recording level con- trols set to maximum so that the VU meters deflect to 0. |
|
9 |
Checking
erasing co- efficient |
|
More than
65 dB |
For the measuring, connect a band pass
filter between the deck and the elec- tronic voltmeter. |
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
IC501 M54410P See the service manual of KD-85A/B/C/E/J/U (No. 4165 – page 7).
2 | 3 | 4 | 5 | 6 | | 7 | 8 | 9 | 10 | | 12 | | | 3 | | | | 4 | 15 | 16 | 18 | 19 | 21 | |||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | 9.2 | 8.6 | 8.0 | 7.6 | 5.5 | 5.1 | 1.0 | 4.8 | 8.8 | 8.8 | 0.2 | 0 | 0 | 0.7 | 17.7 | 8.9 | 10.1 | 8.9 | 10.1 | 11.3 | |
C.Tester | 9.0 | 8.5 | 8.1 | 7.9 | 5.8 | 2.0 | 1.0 | 0.5 | 9.0 | 9.0 | 0.2 | 0 | 0 | 0.8 | 18.1 | 9.0 | 10.3 | 9.0 | 10.3 | 11. | |
201 | 9.3 | 8.63 | 7.7 | 7.6 | 5.2 | 5.1 | .1 | 4.6 | 8.4 | 8.3 | 0.4 | 0 | 0.1 | 0.7 | 17.1 | 8.4 | 9.7 | 8.4 | 9.7 | 11.0 | |
201 | E.Voltmeter | 9.2 | 8.5 | 8.0 | 8.0 | 5.5 | 2.0 | 1.1 | 0.6 | 8.8 | 8.8 | 0.4 | 0 | 0.1 | 0.7 | 17.8 | 8.8 | 10.1 | 8.8 | 10.1 | 11.0 |
10001 | C.Tester | 10.4 | 10.4 | 10.4 | 0 | 10,4 | 10.4 | 10.4 | 20.9 | ||||||||||||
10.901 | E.Voltmer | 10.2 | 10.2 | 10.2 | 0 | 10.2 | 10.2 | 10.2 | 20.5 | ||||||||||||
10000 | C.Tester | 10.4 | 10.4 | 10.4 | 0 | 10.4 | 10.4 | 10.4 | 20.9 | ||||||||||||
10902 | E.Voltmeter | 10.2 | 10.3 | 10.2 | 0 | 10.2 | 10.3 | 10.3 | 20.5 | ||||||||||||
C.Tester | 0 | 0 | 0 | 2.7 | 2.7 | 0 | 0 | 12.0 | 0 | 0 | 0 | 0 | 0 | 0 | |||||||
10903 | E.Voitmeter | 0 | 0 | 0 | 2.7 | 2.7 | 0 | 0 | 12.3 | 0.3 | 0.3 | 0.3 | 0.5 | 0.5 | 0 | ] |
X51 | Е | D | В |
Remote Cont
Rec Muting |
---|---|---|---|---|
O Tastar | 0 | 20.5 | 0 | ON |
C. Lester | 0 | 0 | 0 | OFF |
E Voltmatr | 0 | 20.6 | 0 | ON |
E.vonnen | 0 | 0 | 0.7 | OFF |
1. Unless otherwise specified, all resistors are 1/4 W, ± And all capacitors are 50 V fixed ceramic capacitors
2. UF – Unflamable carbon resistor
MF – Metal film resistor
OMF- Oxided metal film resistor
Ta – Tantalum solid electrolytic capacitor
LL - +20% low leak current electrolytic capacit
8.9 10.1 11.2 15.2 CC 9.0 10.3 11.5 11.5 11.6 15.7 8.4 9.7 11.0 14.9 CC | |
---|---|
9.0 10.3 11.5 11.5 11.6 15.7 8.4 9.7 11.0 14.9 0 | FF |
8.4 9.7 11.0 14.9 0 | )N |
FF | |
8.8 10.1 11.4 15.4 | N |
istors are 1/4 W, ± 5% carbon resistors.
PS – Polystyrene capacitor
Red line shows the signal at recording and +B circuits.
4. parts are safety assurance parts. When replacing those parts, make sure to use the specified one.
1 | 2 | 3 | 4 | 5 | 6 | |||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | | || | 12 | ||||
IC501 |
At PLAY
operation 0 |
At STOP
operation 0 |
At FF
operation 0 |
At REW
operation 0 |
At PAUSE
operation 0 |
At REC
operation 0 |
Playback
cassette |
0 REC 5 | PAUSE 5 | PLAY 5 | REW | |||
А |
Others 5
PAUSE |
Others 5 |
Others 5
PAUSE 0.15 |
5
FF.REW |
Others 5
5 |
Others 5 | Others 5 | 0 |
Recording
cassette |
5 Others C | BEW 0.0 | Others 0.1 | Other | |
502 | Other | 5 | Others 4 5 | Others | 0.07 | .7 | REW | |||||||
503 | PLAY 5 |
FF
and 0 |
PLAY 0.2 | REW 0 |
PLAY
and 0.4 |
PLAY.FF
REW 3.5 |
U | PLAY A 3 |
Others U.
PLAY |
15 Others 0 |
.25 Others 3.8
PLAY 0.1 |
Others 0.2
PLAY 2.1 |
5 Others | |
Others 0.1 |
REW
Others 4 |
Others 5 | Others 3.8 |
FF
Others 1.7 |
Others 0.15 | 0 | Others 0.1 | Other | s 5 | Others 5 | Others 0.2 | ? Others | ||
504 | 0.9 | ngi | 3.4 | Acto Stop | AUTO STOP | 0 | REC U.I | REC | 5 | |||||
в | L | 0.5 | 0.9 | 3.4 | Others 0.5 | Others 0.6 | Others 5 | 0 | Others 5 | Others | 5 0.11 | 5 | 3.4 | |
2 | ſ | • • | PLAY DRIVE | |||||||||||
TO AMP PWB | [(59) + | 1050 |
1C501
M54410P |
502 HD 74001
503 or SN 740 |
DON 2560 D511 |
R505
A $270 I.2 |
.2
K § |
||||||||
┛╵╻┍╧╍┥┿╍╍╍ | 2 | ┥╽┌┼╴ | ||||||||||||
C592
0.0IP C593 0.0IP |
STOP FF-0- |
R502
IK |
R | ┽┾┼┽╸ | ||||||||||
с |
MW 4540
REMO CON 2520684(R, 2520684(R, |
╓┚┊╎╽╇┼
┊╶╧┇╋┝┼ |
HEMO REW |
C503
10000+++C5 10V=+22 6.3 |
8504
5.6K 25 3V |
| + | ||||||||
– Die | ode — | PAUSE II -O | 25 | 1C 502-4 | ||||||||||
┝┧╴╺╋┿┿╍
╺┽┽╼┑╿╎╿└ |
B 9
GND AR R508 270 |
10.10502-3 | ||||||||||||
⊢ | 7 6 5 4 3 2 | R50 | R510 270 | 508 (0504-3) | ÷ 44- | |||||||||
– Tra | nsistor – | ן ה ייקראלין אין א | R523 2.2K | |||||||||||
D | 10 | 2 IN34A SIOK | ┝──┤┼┼ |
X502
2SCII62 (B,C) |
74
10 W |
|||||||||
Л |
4A C507
3 2200 6.3V ++ |
D50 | STOP 8 |
j27
5K |
||||||||||
ECE | B ECB | 55070000 | 88 R517 |
STANDBY R553
SIOK C504-4 X512 |
4-2
0P 6 R537 |
28K
28K 28K + 28V + 10 + 10 + 10 + 10 + 10 + 10 + 10 + 10 |
r+++- | |||||||
REC++OFF++PLAY) | R516 C504-1 | 4.7K | ||||||||||||
ſ | VOLTAGE | IMER SW PWB | 1.4148 |
25C458
(C,D) R541 22 |
30 x507
25C1213 (CD) |
2508
2502 2502 2502 2502 2502 250 250 250 25 |
533k | |||||||
Е | L |
SELECT SU
QSS2325-OI |
≚240V a
240V a 2 a 2 a 2 a 2 a 2 a 2 a 2 a 2 a 2 a 2 |
6.3V | POWER SUPPLY | |||||||||
ECB |
VOLTAG
SELE QSS232 |
ic
ct sw 5-011240y |
+ 0000 | 0516 0514 |
×513
2SC458(CD) |
2 R547 1/4
4+3.3 W 6 470 P |
||||||||
SOI
POWER SW |
POWER TRANS |
D FUSE 2
O TI.6A |
9
|
R548
33 (F) |
||||||||||
· | 1 | POWED TRANS |
VTP66C3-011
VTP66C3-0118 (D-A5AWITH 1 |
S | 522 001 |
C520
519 100+2 513 513 513 513 513 |
c | |||||||
Powe | MODEL | YOLTAGE SELECT SW | POWER T | |||||||||||
F |
0FH728M-
0.022M 120V |
POWER O | C C | MODE | KD - 458 WITH | HOUT PLUG | ||||||||
MQDEL |
ے گالاتے
sw |
OZ20 100V | °− 0 ₽ | |||||||||||
KD-AS | c/J QSPHIO | 222 | ► | ~ | ||||||||||
X51 | 2 | X 509 | 3 | X 50 | 5 | X | 507 | |||||||
AUTO S | TOP | FF 1 | C | B | E | ОВ | E | |||||||
A more | than 1.5 | FF 8 | .4 14 |
.5 PLAY 6
- FF 9 |
.3 |
PLAY
FF |
5.4 REW
8.7 |
0.75 REW | 9.2 | |||||
L | Other unde | er 1 | 0.3 0 | Others ( | 0.08 Others ( | 0.7 Others 0 | .01 15 | .5 Others 0 | 0.1 | Other | 0.01 Others | 0.07 Others | 0.07 |
No. 4182
X 506 | X510 | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
į | B | E | С | В | E | С | В | E | С | В | ||||||
REW | 0.75 | REW | 9.2 | 14.5 | REW | 9.1 | REW | 9.1 |
PLAY FF
0.75 |
REW | 8.5 | REW | 0.07 | |||
II. | Others | 0.07 | Others | 0.07 | 15.5 | Others | 0.07 | 0 | Others | 0.07 | Others 0.1 | 0 | Others | 0.07 | Others | 0.7 |
KD-A5 A/B/E
KD-A5 U
Enclosure Assembly (Except P.W. Board
Ref. No. | Par |
---|---|
1 | VKL31 |
2 | VKL42 |
3 | VJD427 |
4 | T47861 |
5 | VKWA1 |
5 | |
6 | VKZ41 |
/ | VKL45 |
8 | VKL43 |
9 | VKS31 |
10 | VK541 |
11 | VKL42 |
12 | VKZ41 |
13 | VKS410 |
14 | VKL41 |
15 | VKS410 |
16 | VKZ41 |
17 | VKW30 |
18 | VKW41 |
19 | VKL44 |
20 | VKZ41 |
21 | VJT202 |
22 | TJL344 |
23 | VKY41 |
24 | VKY41 |
25–32,34 | ZCKDA |
ZCKDA | |
26 | VJD213 |
27 | VJD425 |
28 | VJD425 |
29 | VJD429 |
30 | νγτα4 |
31 | VJD42 |
32 | VJD429 |
33 | VGM01 |
34 | TJE349 |
35 | VKL44 |
36 | VJD316 |
VJD316 | |
37 | VXP40 |
38 | VKW30 |
39 | VYSH2 |
40 | VKS414 |
41 | VXS40 |
42 | VXP402 |
43 | VKW30 |
44 | VKS414 |
45 | VXP40 |
46 | E48981 |
47 | VXL40 |
VXL40 | |
48 | VXL40 |
VXL40 | |
49 | VXL40 |
VXL40 | |
50 | VXQ40 |
Enclosure Assembly and Electrical Parts List (Except P.W. Board Parts)
A Parts are safety assurance parts.
When replacing those parts, make sure to use the specified one.
Ref. No. | Parts No. | Parts Name | Remarks | Q'ty |
---|---|---|---|---|
1 | VKL3178-00B | Holder Plate Ass'v | 1 | |
2 | VKL4213-002 | Panel Plate | 1 | |
3 | V.ID4273-001 | Indicator | 1 | |
4 | T47861-001S | Pilot Lamo | 1 | |
5 | VKW4133-001 | Knob Spring | 1 | |
6 | VK74120-001 | Sheet | 1 | |
7 | VKI 4507-001 | Lamp Bracket | 2 | |
8 | VK14380-00A | Cross Bar Ass'v | 1 | |
9 | VKS3102-001 | Rack Plate | 1 | |
10 | VKS4110-002 | Brake Arm | 1 | |
11 | VKI 4271-001 | Bubber Betainer | 1 | |
12 | VK74111-001 | Bubber Tire | 1 | |
13 | VKS4109-004 | Brake Drum | 1 | |
14 | VKI 4169-00A | Gear Frame Ass'y | 1 | |
15 | VKS4108-003 | Spur Gear | 1 | |
16 | VK74123-001 | Collar | 1 | |
17 | VKW3001-006 | Spring | 1 | |
18 | VKW4106-001 | Torsion Spring | 1 | |
19 | VK1 4488-00A | Arm Ass'v | 1 | |
20 | VKZ4112-001 | Stop Ring | for Arm Ass'v – Cassette Holder | 1 |
21 | V IT2024-002 | Cassatta Lid | 1 | |
27 | T.II 344518-02 | "SA" Mark | 1 | |
23 | VKY4156-001 | Cassette Spring (1) | 2 | |
24 | VKY4157-001 | " " (2) | 1 | |
25-32 34 | ZCKDA5Y1-CBF | Front Plate Ass'v | KD-A5A/C/J/U | 1 set |
ZCKDA5V2.CBE | KD-458/F | 1 set | ||
26 | V ID 2135-002 | Meter Escutcheon | 1 | |
20 | VID4256-001 | 1 | ||
28 | V ID4257-001 | 1 | ||
20 | VJD4294-001 | |||
30 | VYTA435-001 | Blind | 1 | |
31 | V ID4259-001 | for Fiect | 1 | |
32 | VID4295-001 | for Power | 1 | |
33 | VGM0110-008 | Level Meter | 2 | |
34 | T.IF349408-02 | Counter Lens | 1 | |
35 | VK14440-001 | Switch Bracket | 1 | |
36 | VID3167-001 | Button Case | KD-454/C/1/U | 1 |
00 | VJD3167-002 | KD-A5B/F | 1 | |
37 | VXP4023-002 | Push Button | 6 | |
38 | VKW3001-019 | Compression Spring | 6 | |
39 | VYSH203-001 | Button Spacer | 6 | |
40 | VKS4147-001 | Switch Holder | 1 | |
41 | VXS4019-001 | Knob | for Timer Switch | 1 |
42 | VXP4024-00A | Knob Ass'v | for Eiect | 1 |
43 | VKW3001-031 | Compression Spring | 1 | |
44 | VKS4148-001 | Remote Bar | 1 | |
45 | VXP4032-001 | Knob | for Power Switch | 1 |
46 | E48981-001 | Stopper Pin | for Power Switch | |
47 | VXL4060-00A | Knob Ass'y | for Input (Right channel) KD-A5A/C/J/U | 1 |
VXL4068-00A | Volume Knob (R) Ass'y | KD-A5B/E | 1 | |
48 | VXL4061-00B | Knob Ass'y | for Input (Left channel) KD-A5A/C/J/U | 1 |
VXL4067-00B | Volume Knob (L) Ass'v | KD-A5B/E | 1 | |
49 | VXL4062-00A | Knob Ass'y | for Output KD-A5A/C/J/U | 1 |
VXL4069-00C | ,, · | KD-A5B/E | 1 | |
50 | VXQ4017-001 | Lever Knob | 4 |
Ref. No. | Parts No. | Parts Name | Remarks | Q'ty |
---|---|---|---|---|
51–53 | ZCKDA5Y-CCA | Cassette Lid Ass'y | 1 | |
51 | VJT3031-001 | Cassette Door | 1 | |
52 | VJT3032-001 | Door Plate | 1 | |
53 | VJZ4008-001 | Double Face | 1 | |
54 | VJD3168-001 | Jack Escutcheon | 1 | |
55 | VKL1139-001 | Bottom Cover | 1 | |
56 | VJF3001-001 | Foot | 4 | |
57 | VKL1138-001 | Top Cover | 1 | |
58 | VKL3001-002 | Special Screw | 4 | |
59 | VYN2047-002GA | Name Plate | KD-A5A | 1 |
" -001GA | KD-A5B | | 1 | ||
" -003GA | KD-A5C | 1 | ||
" -004GA | " | KD-A5E | | 1 | |
′′ -005GA | KD-A5J | 1 | ||
-006GA | KD-A5U | 1 | ||
60 | E48729-002 | Plastic Rivet | 2 | |
61 | VKL4441-001 | Switch Bracket | for Power Switch | 1 |
62 | USP2111-011 | Push Switch | KD-A5A/E (Power SW) | 1 |
-011BS | KD-A5B (Power SW) | 1 | ||
USF1110-222 | 1 | |||
62 |
-221
OEA720M 222 |
M.P. Capacitor | 1 | |
03 | OFH72BM 222 | |||
OFH530M-223 | 1 | |||
64 | T47047-001 | Condenser Boot | KD-A5U/U | 1 |
65 | TAP344324-01 | Power Transformer | ||
00 | TAP344324-01 | KD-A5B | 1 | |
TAP344325-01 | KD-A5D/L | 1 | ||
VTP66U3-011 | KD-A5U | 1 | ||
66 | F4932-002 | Special Washer | for Power Transformer | 2 |
67 | TAW000504-01 | Connector | 2 | |
68 | VKL1136-001 | Front Bracket | 1 | |
69 | QSS2301-101 | Slide Switch | for Timer Switch | 1 |
70 | VMW4531-001 | P.W. Board | for Switch | 1 |
71 | VKS2104-001 | Lamp Hood | 1 | |
72 | QMG1121-003 | Lamp Holder | for Lamp | 2 |
73 | QLP4101-005S | Lamp | VJZ4006-001 = Lamp Shade | 2 |
74 | VKL1137-003 | Rear Bracket | KD-A5C/J | 1 |
.004 | KD-A5A/U | 1 | ||
′′ -005 | ,, | KD-A5B/E | 1 | |
75 | QMP2560-200 | Power Cord with Plug | KD-A5A | 1 |
QMP9017-008BS | Power Cord | KD-A5B | 1 | |
QMP1200-200 | Power Cord with Plug | KD-A5C/J | 1 | |
QMP3900-200 | KD-A5E | 1 | ||
QMP7600-200 | KD-A5U | 1 | ||
76 | QHS3876-162 | Strain Relief Bushing | KD-A5A/C/E/J/U | 1 |
····· | KD-A5B | 1 | ||
//
70 |
VK24001-010 | Wire Holder | 3 | |
70 | 0000001 | 1 | ||
/9 | US52301-006 | Slide Switch | 55 | 1 |
0U
01 |
V IVIVV4533-001 | F.W. Board | 1 | |
83 | VIXW4153-004 |
noider Spring (K)
Sheet |
||
VIN2-120-001 | JUCCI |
Ref. No. | Parts No. | Parts Name | Remarks | Q'ty |
---|---|---|---|---|
84 | VYSH106-028 | Spacer | 1 | |
85 | T47818-002 | " | 3 | |
86 | TJF338415-01 | Foot | 3 | |
87 | VKL4503-001 | Bracket | 1 | |
88 | VKZ4001-011 | Wire Holder | 3 | |
89 | VYSR108-003 | Spacer | 1 | |
90 | VYSH103-009 | 1 | ||
91 | VKL4506-001 | Transformer Bracket | 1 | |
92 | QMC0888-008 | DIN Socket Ass'y | for Remote Control | 1 |
93 | QMG1321-002BS | Fuse Holder | KD-A5B | 1 |
94 | QMF51A2-R20LBS | Fuse | KD-A5B | 1 |
95 | *TAZ000509-08 | Fuse Seal | KD-A5B | | 1 |
98 | QSS2325-011BS | Slide Switch | KD-A5B, for Voltage Selector | 1 |
" -011 | KD-A5A/E " | 1 | ||
QSR0084-001 | Voltage Select Switch | KD-A5U | 1 | |
99 | VKL4275-001 | Bracket | for Voltage Select SW. (KD-A5U) | | 1 |
100 | Q03095-206 | Washer | | 1 | |
101 | Q03093-524 | Rubber Tire | 1 | |
102 | ONS26007 | ,, | Gear Frame Ass'v | 1 |
103 | BEE2000 | E Ring | Spur Gear x 1, Arm Bracket x 1, Eject Knob x 1 | 3 |
104 | BEE2500 | Head Plate Ass'y – Cross Bar Ass'y | 2 | |
105 | DPSP4012ZS | Screw | Power Transformer | 2 |
106 | LPSP2604Z | ,, | Timer Switch x 2, Bracket x 1 | 3 |
107 | 1 PSP2606Z | Bottom Case | 2 | |
108 | L PSP2608Z | ,, | Spur Gear | 1 |
109 | LPSP3006ZS | Power Switch x 2, Voltage Select SW x 2 | 4 | |
110 | SBSB2606Z | Tapping Screw | Lamp Bracket x 2, Switch Holder x 2 | 4 |
111 | SBSB2610Z | Switch P.W. Board | 3 | |
112 | SBSB3005R | Rear Bracket x 1, Jack Cover x 2 | 3 | |
113 | SBSB30067 | Gear-oiled Damp Ass'y x 2, Bottom Cover x 5, | 26 | |
Mecha. Ass'y x 4, Switch Bracket x 2, Front | ||||
Bracket x 6, Rear Bracket x 4, Lug x 1, Wrapping | ||||
Terminal x 1, Fuse Holder (KD-A5B) x 1 | ||||
114 | SBSB3008Z | Foot x 4, Fuse Holder x 2 | 6 | |
115 | SDSP2605R | Screw | for P.W. Board (VMW4533-001), Remote Socket x 2, | 5 |
Slide SW (S5) x 2 | ||||
116 | SSSP2604N | Button Case – Switch Bracket | 3 | |
117 | SBSB3006V | Amp. P.W. Board x 4, Control P.W. Board x 4 | 8 | |
118 | LPSP3006VS | Lever Switch | 4 | |
119 | SDBP2005N | | 1 | ||
120 | SDSB3006Z | front plate | 3 | |
121 | WNS4000N | Washer | 2 | |
122 | WLS4000 | Lock Washer | 2 | |
123 | NTB3000S | Nut | KD-A5A/B/E/U for Voltage Selector | 2 |
120 | SDBP3010BS | Screw | " | 2 |
124 | 000100000 | 00101 | 1 |
KD-A5A/B/C/E/J/U
No. 4182
- 22 -
- 22 —
Ref. No. | Parts No. | Parts Name | Remarks | Q'ty |
---|---|---|---|---|
1 | VKL1118-00D | Chassis Base Ass'y | 1 set | |
2 | VYSR201-003 | Spacer | 1 | |
3 | VKL4361-002 | Brake Bar | 1 | |
4 | VYSF101-012 | Spacer | 2 | |
5 | VKW4145-001 | Brake Bar Spring | for Brake Bar | 1 |
6 | VKL4362-001 | Lock Bar | 1 | |
7 | VKZ4005-001 | Stopper | for Brake Bar | 1 |
8 | VSH1102-001 | Leaf Switch | 1 | |
9 | VKS4135-00A | Lock Lever Ass'y | 1 | |
10 | VKL4366-00A | Play Arm Ass'y | 1 | |
11 | VKL4479-001 | Flywheel Cover | 1 | |
12 | VKW4149-001 | Play Solenoid Spring | 1 | |
13 | T44341-001 | Rubber Tire | 1 | |
16 | VKS4142-001 | Push Arm (1) | ||
17 | VKS4143-001 | " (2) | 1 | |
18 | VKW4141-001 | Push Arm Spring | 1 | |
19 | VKS3109-001 | Switch Holder (L) | 1 | |
20 | VMW4522-001 | P.W. Board (L) | _ | 1 |
21 | QSP0029-001 | Slide Switch |
י
ר |
|
22 | QMV5004-004 | Connector | _ | 2 |
23 | VKS3110-001 | Switch Holder (B) | 1 | |
24 | VKH4215-001 | Head Collar | for Erase Head | 1 |
25 | VKH4196-001 | Shaft | 1 | |
26 | VKS4136-001 | Switch Lever | 1 | |
27 | VKS4137-001 | Pressure Lever | 1 | |
28 | VKH4196-002 | Shaft | 1 | |
29 | VKW4138-001 | Pressure Lever Spring | 2 | |
30 | VKL4399-001 | Eject Safety Lever | 1 | |
31 | VKW4142-001 | Connecting Wire | 1 | |
32 | VKW3002-004 | Spring | 1 | |
33 | VKZ3003-001 | Rubber Tube | 2 | |
34 | VKL4370-00C | Slide Base Ass'v | 1 | |
35 | VKP4105-00A | Pinch Roller Bracket Ass'y | 1 | |
36 | VKL4371-001 | Push Arm | 1 | |
37 | VKW4139-001 | Pinch Roller Spring | 1 | |
38 | VKS2102-001 | Head Mount Base | 1 | |
39 | ZMM074401-0D | REC/PB Head Ass'v | 1 | |
40 | VKW3001-020 | Compression Spring | for REC/PB and E Heads | 2 |
41 | ZMM090414-0A | 1 | ||
42 | VKW3002-005 | Tension Spring | for Slide Base | 1 |
43 | TEP357469-02 | Stopper | 1 | |
44 | VKL3155-00A | Reel Disk Bracket Ass'y | 1 | |
45 | VKR4113-00A | Take-up Reel Ass'y | 1 | |
46 | VKR4118-00A | Supply Reel Ass'v | 1 | |
47 | VKS4130-001 | Back Tension Base | 1 | |
49 | VKW3001-026 | Compression Spring | for Back Tension | 1 |
50 | VKS4131-001 | Reel Stopper | 2 | |
51 | VKS4151-00A | Idler Ass'y Unit | 1 | |
52 | VKL4484-001 | Lock Lever | 1 | |
53 | VKW3002-027 | Spring | 1 | |
54 | TJN265559-04 | Silencer | for Spring | 1 |
Farts Name | nellia K$ | |||
---|---|---|---|---|
56 | _ | |||
57 | VKW4134-001 | Idler Spring | 1 | |
58 | MDN-7V | Reel Motor | | 1 | |
59 | VKR4121-001 | Motor Pulley | | 1 | |
60 | VKF3107-00A | Flywheel Ass'y | 1 | |
61 | VKF3103-00B | Capstan Metal | 1 | |
62 | T30301-137 | Spring | | 1 | |
63 | VKB3001-007 | Capstan Belt | | 1 | |
64 | VKL4372-00B | Flywheel Holder Ass'y | | 1 | |
65 | VKL4368-002 | Play Solenoid Lever | 1 | |
66 | VKW4137-001 | Connecting Wire | | 1 | |
67 | TEP357456-01 | Thrust Screw | 1 | |
68 | VKL4398-002 | Play Solenoid Bracket | 1 | |
71 | VGP0301-002 | D.C. Solenoid Ass'y | for Play | | 1 |
72 | VKL3161-002 | Motor Bracket | 1 | |
73 | MH15C2HDN | D. C. Motor | for Capstan | | 1 |
74 | VKS4139-002 | Motor Pulley | | 1 | |
75 | TER357465-03 | Cushion Rubber | 3 | |
76 | VKZ4109-001 | Motor Screw | 3 | |
77 | TFB345469-01 | Rubber Stopper | 1 | |
78 | VGP0201-003 | D.C. Solenoid Ass'y | for Brake | 1 |
79 | VKL4363-002 | Lock Solenoid Lever | ||
80 | VKH4194-001 | Shaft | 1 | |
82 | T43909-008 | Metal | | 1 | |
83 | VKL4485-00A | Eject Lever Ass'y | 1 | |
84 | VKW4156-001 | Shaft Arm Spring | 1 | |
85 | VKC5122-001T | Counter Ass'y | 1 | |
86 | VKB3000-012 | Counter Belt | | 1 | |
87 | VMW4530-001 | P.W. Board | ||
88 | DN6835 | Hole I.C. | 1 | |
89 | QMV5005-003 | Connector | ||
90 | VKL4487-00B | Mecha. Bracket (L) Ass'y | ||
91 | VKL4486-00A | " (R)Ass'y | ||
92 | VKL4403-00B | Shift Arm Ass'y | 1 | |
93 | T43909-004 | Metal | for Shift Arm | |
94 | — | _ | ||
105 | QD3093-825 | Washer | for Crossbar | 2 |
1 | ||||
003093-522 |
vvasher
Washer |
for Flywheel | ||
113 |
203093-621
" 027 |
|||
114 |
-027
REE2000 |
E Bing | for Push Arm | |
110 | DEE2500 | Play Arm v 1 Lock Lever v 1 Play Salenaid Lover | 6 | |
116 | REE2500 | x 1, Shaft x 1, Cassette Holder – Cassette Cover | ||
117 | Commu | Ass y x Z | 1 | |
11/ | Screw | Flywneel Cover | ||
110 | UT3A20122 |
Jule Dase
Macha Brackat (B) x 2 Matal x 1 Macha Brackat |
6 | |
119 | LL9L70097 | (1) x 2 Motol x 1 | ||
120 | 1 85826067 | Canstan Metal x 3 Flywheel Holder x 1 Motor | 5 | |
120 | Bracket x 1 |
Ref. No. | Parts No. | Parts Name | Remarks | Qʻty |
---|---|---|---|---|
121 | SBSB3006Z | Tapping Screw | Mecha. Ass'y | 4 |
122 | SBSB2608Z | Leaf Switch | 1 | |
123 | SBSB2610Z | Flywheel Holder x 2, Motor Bracket x 3 | 5 | |
124 | SDSP2606Z | Screw | for P.W. Board | 4 |
125 | SPSX2010N | " | REC/PB and E. Heads | 1 |
126 | SPSP2006N | Head Mount Base | 1 | |
127 | SPSP2603Z | Reel Motor | 3 | |
128 | SPSP2605Z | " | Switch Holder | 5 |
129 | SPSP3003ZS | " | Solenoid x 2, Solenoid x 2 | 4 |
130 | · _ | |||
131 | SSSB2608Z | Screw | Counter | 2 |
132 | YRS2603B | " | Motor Pulley | 1 |
133 | SPSP2606Z | Reel Unit Ass'y | 4 | |
134 | LPSP2604Z | " | Play Solenoid Bracket x 3, Rubber Stopper x 1 | 4 |
Main Amp. P.W. Board Parts List
A parts are safety assurance parts.
When replacing those parts, make sure to use the specified one.
Ref. No. | Parts No. | Parts Name | Remarks | Q′ty |
---|---|---|---|---|
VMW1522-002A | P.W. Board | No supply as parts ass'y | 1 | |
R101, 201, 118, 218, 143, 243 | QRD141K-822 | C. Resistor | 8.2 kΩ ¼ W | 6 |
R102.202.169.269.311.411.929 | -392 | " | 3.9 kΩ ″ | 7 |
R105, 205, 114, 214, 132, 232. | ··· -472 | 4.7 kΩ " | 14 | |
147, 247, 170, 270, 182, 282, | ||||
924, 941 | ||||
B106, 206, 308, 408, 930, 931. | "-151 | 150 Ω " | 9 | |
932 933 934 | ||||
B107 207 183 283 | OBZ0019-823 | " (Low Noise) | 82 kΩ ″ | 4 |
B108, 208, 192, 292, 310, 410 | ORD141K-273 | C. Resistor | 27 kΩ " | 6 |
R109, 209, 117, 217, 120, 220 | .103 | " | 10 kΩ " | 19 |
171 271 129 229 154 254 | 100 | |||
302 402 902 919 923 946 | ||||
955 | ||||
B110 210 | .101 | 100 \Q " | 2 | |
B111 211 | OBZ0019-823 | " (Low Noise) | 82 kΩ " | 2 |
B112 212 | OBD141K-102 | C Besistor | 1 kΩ " | 2 |
B113 213 | "681 | " | 680 9 " | 2 |
B115 215 | -001 | 180 kΩ " | 2 | |
R116 216 142 242 021 | " 152 | 5 | ||
R110, 210, 142, 242, 521 | -152 | 10 | ||
162 262 169 269 199 299 | - 104 | 100 K32 | 19 | |
102, 202, 108, 208, 188, 288, | ||||
194, 294, 303, 403, 912, 917, | ||||
B126 226 172 272 | 200 10 " | |||
R120, 220, 172, 272 | -394 | 4 | ||
R120, 220, 190, 290 | -124 | 4 | ||
R130, 230, 197, 297, 199, 299 | -121 | ,, | 0 | |
R131, 231 | -503 | 50 K12 | ||
-473 | 47 K32 | 14 | ||
300, 400, 905, 911, 913, 916, | ||||
950, 951 | 0710 // | |||
R144, 244, 150, 250, 152, 252 | -2/2 | 6 | ||
R145, 245, 301, 401 | -222 | " | 2.2 K32 | 4 |
R148, 248, 195, 295 | -152 | 4 | ||
R151, 251 | -183 | 18 kS2 " | 2 | |
R153, 253 | -680 | 68 22 " | 2 | |
R155, 255 | QRD146K-181 | Unflamable Resistor | 2 | |
R157, 257 | QRD141K-4/4 | C. Resistor | 470 kS2 " | 2 |
R 158, 258, 165, 265, 196, 296, | -223 | 22 KS2 | 13 | |
904, 905, 918, 928, 937, 942, | ||||
945 | ||||
R 161, 261, 166, 266, 198, 298 | -820 | 6 | ||
R 103, 203, 180, 280 | -334 | 330 K12 " | 4 | |
R167, 267, 304, 404, 309, 409, | -332 | 3.3 K12 | 8 | |
901, 925 | 0001441/ 202 | 0 During | 20160 1/ 1/ | 2 |
R 184, 284 | URD141K-393 | C. Resistor | 39K32 % W | 2 |
D100, 200 | -564 | 200 K77 | 2 | |
R 307 407 910 | URD 14 1K-563 | 50K32 | 2 | |
8187 287 QAG QA7 Q14 Q26 | -104 | 3 | ||
027 | -083 | 00 K27 | 1 | |
B103 203 | // 105 | 12 MO " | ||
B903 | 080146K 221 | Linflamable Resistor | ||
R909 954 | 080140K-331 | |||
C. NESISIOI | 470.32 | 2 |
-
- 28 -
6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | |4 | 15 | 16 |
---|---|---|---|---|---|---|---|---|---|---|
AUTO
STOP |
REC | RE | 2 | |||||||
ţ | 0.1 | 5 | ||||||||
0thers
5 |
0 |
Others
5 |
Oth
0 |
ners
. I |
5 | 3.4 | 1.0 | 5 | ||
At PAUSE
operation |
At REC operation |
Playback
cassette 0 |
REC | PAUSE | PLAY | REW |
FF
and REW |
PLAY | ||
0 | 0 | Pasardina | 5 | 5 | 5 | 5 | 3.9 | 5 | ||
0thers
5 |
Others
5 |
0 |
cassette
5 |
Others
0.1 |
Others
0.1 |
Others
0.1 |
Others
0.1 |
Others
0.1 |
Others
0.1 |
5 |
PLAY,
FF, BFW |
PLAY
A |
PL | ٩Y | PLAY | PLAY | PLAY | ||||
3.5 | 3 | 1.5 | 0.1 | 2.1 | 5 | |||||
0thers
0.15 |
0 |
Others
0.1 |
Otł |
ners
5 |
Others
5 |
Others
0.2 |
Others
0.1 |
5 | ||
FIF,
RE W |
FF | FF |
FF,
REW |
REW | REW | REW | ||||
0.07 | 0.07 | 5 | 1.7 | 0.07 | 1.6 | 5 | ||||
Others
3.5 |
0 |
Others
3.8 |
Others
0.15 |
Others
0.25 |
Others
3.8 |
Others
0.25 |
Others
0.15 |
5 | ||
∧— positive flash voltage ∨— negative flash voltage
Voltage values are measured by the following meter without input signal at playback mode.
C. Tester = Circuit Tester (20 kΩ /V impedance)
E. Voltmeter = Electronic Voltmeter
Ref. No. | Parts No. | Parts Name | Remarks | Q′ty |
---|---|---|---|---|
B920 947 | OBD146K-151 | Linflamable Resistor | 150 Ω 1 / 4 W | 2 |
R022 | OBD1//3K 153 | C Basistor | 1 | |
R042 | OPD141K 151 | 1 | ||
R943 | ,, | 1 | ||
-082 | 0.8 K12 | |||
R948 | URD146K-471 | Unflamable Resistor | 470 52 | |
R949 | -391 | 390.77 | ||
R952, 953 | -100 | 10.52 | 2 | |
QWY123-022 | Bas. Wire | for Jump | 28 | |
C101, 201 | QCS11HJ-221 | F. Ceramic Capacitor | 220 pF 50 V | 2 |
C102, 202 | " -391 | ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, | 390 pF " | 2 |
C103, 203, 109, 209, 151, 251 | QEB41EM-475M | E. Capacitor (Low Leak) | 4.7 μF 25 V | 6 |
C104, 204 | QCS11HJ-101 | F. Ceramic Capacitor | 100 pF 50 V | 2 |
C105, 205, 126, 226, 129, 229, | QEW41CA-336N | E. Capacitor | 33 μF 16 V | 15 |
130, 230, 131, 231, 179, 279, | ||||
903, 911, 914 | 0.00044111.000 | |||
UCSTIHJ-680 | F. Ceramic Capacitor | 68 pF 50 V | 2 | |
QEW40JA-227N | E. Capacitor | 220 µF 6.3 V | 4 | |
QFM41HJ-183 | Mylar Capacitor | 0.018 μF 50 V | 2 | |
C110, 210, 155, 255, 171, 271 | QEW41EA-336N | E. Capacitor | 33 μF 25 V | 6 |
C111, 211 | QFM41HJ-822 | Mylar Capacitor | 0.0082 μF 50 V | 2 |
C116, 216, 117, 217 | QEB41EM-105N | E. Capacitor (Low Leak) | 1 μF 25 V | 4 |
C118, 218, 136, 236, 138, 238 | QCS11HK-151 | F. Ceramic Capacitor | 150 pF 50 V | 6 |
C119, 219, 172, 272 | QCS11HJ-201 | 200 pF " | 4 | |
C120, 220, 143, 243, 163, 263 | QFM41HJ-102 | Mylar Capacitor | 0.001 μF " | 8 |
169, 269 | ||||
C127, 227, 901, 907, 909 | QEW41EA-227N | E. Capacitor | 220 μF 25 V | 5 |
C128, 228 | QEN41EA-335N | Non-polarized E. Capacitor | 3.3 μF " | 2 |
C133, 233, 134, 234, 154, 254, | QEW41AA-107N | E. Capacitor | 7 | |
908 | ||||
C135, 235 | QEW41EA-475N | 4.7 μF " | 2 | |
C144, 244, 164, 264, 170, 270, | QEW41HA-105N | 1 μF 50 V | 11 | |
176, 276, 180, 280, 921 | ||||
C139, 239 | QFM41HJ-272 | Mylar Capacitor | 0.0027 μF ″ | 2 |
C140, 240 | -273 | 0.027 μF " | 2 | |
C141, 241 | -682 | 0.0068 μF ″ | 2 | |
C142, 242 | QCS11HK-471 | F. Ceramic Capacitor | 470 pF " | 2 |
C145, 245 | QEW41AA-476N | E. Capacitor | 47 μF 10 V | 2 |
C146, 246 | OEB41EM-335N | " (Low Leak) | 3.3 µF 25 V | 2 |
C152 252 | OCS11HK-471 | Ceramic Capacitor | 470 pF 50 V | 2 |
C153 253 | OEB41HM-105M | E Capacitor (Low Leak) | 1 µF " | 2 |
C156, 256 | OEB41EM-105N | 1 µE 25 V | 2 | |
C162 262 | 00511HL681 | Ceramic Canacitor | 680 pE 50 V | 2 |
OEM41H1 152 | Mylar Capacitor | 0.0015 // 50 V | 2 | |
C165 265 | ····································· | 0.0010 m | 2 | |
C166 266 | 0001141201 | Ceramic Capacitor | 200 pE " | 2 |
C167 267 | OEM/141122 | 0.012 //F " | 2 | |
OEM/101200 | 0.012 µ1 | 2 | ||
UCINI4101J-392 | 0.0039 µ1 50 V | 2 | ||
-4/2 | Commin Committee | 2 | ||
QCS11HJ-391 | 390 pr | 2 | ||
UFS32BK-221 | Polystyrene Capacitor | 220 pF | 2 | |
61/5, 2/5 | UEW41HA-105N | E. Capacitor |
ιμ
|
2 |
Ref. No. | Parts No. | Parts Name | Remarks | Q′ty |
---|---|---|---|---|
C177, 277
C178, 278, 904, 912 C902, 913 C905, 906 C915, 920 C916 C917 C922 C923 C924 C925 C926 |
QEW41CA-476N
QEW41CA-106N QEW41EA-475N QFM41HK-822 QFM41HK-103 QEW41CA-107N QFM42AK-223 QEW41EA-106N QFS32BK-682 QEW41EA-477N QEW41CA-106N QCF11HP-472 |
E. Capacitor
" Mylar Capacitor " E. Capacitor Mylar Capacitor E. Capacitor E. Capacitor Polystyrene Capacitor E. Capacitor Ceramic Capacitor |
47 μF 16 V 10 μF " 4.7 μF 25 V 0.0082 μF 50 V 0.01 μF " 100 μF 16 V 0.022 μF 100 V 10 μF 25 V 0.0068 μF 470 μF 25 V 0.0068 μF 470 μF 25 V 0.0047 μF 50 V |
2
4 2 2 1 1 1 1 1 1 1 1 1 |
VR101, 201
VR102, 202, 104, 204 VR106, 206 VR107, 207, 108, 208, 109, 209 |
QVP8A0B-053
'' -024 '' -052 QVP4A0B-224 |
V. Resistor
'' '' |
PB. EQ.
PB. GAIN, REC. GAIN METER BIAS NORMAL, BIAS METAL, BIAS CHROME |
2
4 2 6 |
L102, 201, 104, 204, 102, 202
L103, 203 L901 T901 |
VQP0001-183S
TAC000320-07 VQP0001-102S VQH1009-003 |
Inductor
" Osc. Coil |
18 mH
5.6 mH 1 mH |
6
2 1 1 |
X101, 201, 102, 202
X103, 203 X104, 204, 105, 205, 109, 209, 113, 213 X106, 206, 107, 207, 110, 210, 111, 211, 114, 214, 902, 903, 907, 908 X108, 208 X112, 212 X901 X904, 905, 906 |
2SC1980(T,U)
2SC1684(R,S) 2SC1327(T,U) 2SC1684(R,S) 2SC1327(U) 2SD468(B,C) 2SA921(T,U) 2SA564(R,S) |
Si. Transistor |
4
2 8 14 2 2 1 3 |
|
X909, 910, 911
IC101, 201 IC901 IC902 IC903 |
2SC1685(R,S)
TAT000351-01 UPC4558C UPC4557C LB1416 |
Super ANRS IC
IC " |
3
2 1 1 1 |
|
D101,201,102,202,103,203,901
D902,904–907,909,910 D903,908 |
OA90
MA150 RD4.3E(C) |
Ge. Diode
Si. Diode Zener Diode |
7
7 2 |
|
S1
S2 S3 S4 CN901 CN902 VR105, 205 |
QSL4309-022
"-021 QSL8309-001 QSL8209-012 VMJ5002-003 VMJ6002-003 QMV5005-006 "-003 QVD8A2A-014V VKL3143-001 E43727-002 |
Lever Switch
,, ,, MIC & HP Jack Ass'y PIN Jack Ass'y Plug Ass'y V. Resistor Board in Tab Wrapping Tab |
Input Select
ANRS SW. Tape Select Metal R/P Head E. Head Output Volume |
1
1 1 1 1 1 1 1 6 22 |
▲ parts are safety assurance parts.
When replacing those parts, make sure to use the specified one.
Ref. No. | Parts No. | Parts Name | Remarks | Q'ty |
---|---|---|---|---|
VMW2514-006 | P W Board | No supply as parts ass'y | 1 | |
B502 | ORD141K-102 | C. Besistor | 1 kΩ 1/4 W | 1 |
B504 | .562 | " | 56k0 " | 1 |
8505 508 510 530 | 270 0 " | 1 | ||
R506 517 | ·2/1 | 4 | ||
PE07_EE2 | -101 | 2 | ||
R507, 552 | -122 | 1.2 K32 | 2 | |
R509, 514 | -331 | 330 52 " | 2 | |
R512, 554 | "-561 | 560 \2 " | 3 | |
R513 | | '' -391 | 390 Ω " | 1 | |
R516 | -681 | ** | 680 Ω " | 1 |
R518 | "-473 | ,, | 47 kΩ ″ | 1 |
R519, 520, 521, 522, 553 | " -103 | 10 kΩ " | 5 | |
R523, 529 | "-222 | ,, | 2.2 kΩ " | 2 |
R524, 555, 557 | "-560 | 56 Ω " | 3 | |
R537 | .472 | 47kΩ " | 1 | |
B527 | ″ -152 | 15kΩ " | 1 | |
B528 541 | // _220 | 22 0 " | 2 | |
R521 | " 601 | 690 0 " | 2 | |
DE22 | OME Desister | 000.32 | ||
N533 | URG019J-220 | U.M.F. Resistor | 22.52 | |
R536 | QRD121K-102 | 1 kΩ2 " | 1 | |
R542 | QRG019J-151 | O.M.F. Resistor | 150 Ω ″ | 1 |
R543 | QRG029J-330 | " | 33 Ω " | 1 |
R544 | ··· -120 | " | 12 Ω " | 1 |
R545 | QRD126K-560 | C. Resistor | 56 Ω 1/2 W | 1 |
R546 | QRG029J-331 | O.M.F. Resistor | 330 Ω | 1 |
R547 | QRD146K-3R3 | C. Resistor | 3.3 Ω 1/4 W | 1 |
R548 | QRD146K-330 | Unflamable Resistor | 33 Ω 1/4 W Λ | 1 |
R549 | ORD141K-822 | C. Resistor | 82kΩ " | 1 |
R550 | .333 | " | 33 40 " | 1 |
B551 526 | " 682 | 6 9 k 0 " | 2 | |
R556 | -002 | 2 | ||
DE20 | -003 | ,,, | 50 K32 | |
-272 | OMEDIA | 2.7 K32 | ||
n533 | QRG019J-220 | O.M.F. Resistor | 2277 | |
UWY123-022 | Bas. Wire | 19 | ||
0500 | 0.5 | |||
0502 | QEW40JA-22/N | E. Capacitor | 220 μF 6.3 V | 1 |
C503, 504 | QEW41AA-107N | | " | 100 μF 10 V | 2 |
C505 | -108N | 1000 μF " | 1 | |
C507 | *QEW40JA-228N | " | 2200 μF 6.3 V | 1 |
C508, 509, 511 | QEW41EA-475N | " | 4.7 μF 25 V | 3 |
C510 | " -106N | " | 10 μF " | 1 |
C512 | QEB41EM-106N | Low Leak E. Capacitor | 10 μF " | 1 |
C513, 514, 515 | QEW40JA-477N | E. Capacitor | 470 μF 6.3 V | 3 |
C516 | QEW41VA-477N | 470 μF 35 V | 1 | |
C517 | QEW41CA-106N | ,, | 10 µF 16 V | 1 |
C518 | QEW41EA-106N | ,, | 10 µF 25 V | 1 |
C519 | ,, | 100 uE " | 1 | |
C520 | *OFT/140 220N | 2200 //E 50 V | 1 | |
C521 522 | E Coromio Conscitor | |||
C524 | OEW/41EA 4000 | 2 | ||
C525 | ||||
LOW Leak E. Capacitor | 3.3 μτ | |||
QCF11HP-102 | F. Ceramic Capacitor | 0.001 μ⊢ 50 V | 1 | |
0592-597, 523 | -103 | 0.01 μF " | 7 | |
X501, 502 | 2SC1162(B, C) | Si. Transistor | 2 | |
X504, 505, 506 | 2SC458(C, D) | " | 3 | |
X507, 508 | 2SC1213(C.D) | " | 2 | |
X509, 510 | 2SC458(C. D) | 2 | ||
X511 | 2SC1162(B_C) | 1 | ||
1 | • |
Ref. No. | Parts No. | Parts Name | Remarks | Q'ty |
---|---|---|---|---|
X512, 513 | 2SC458(C,D) | Si. Transistor | 2 | |
IC501 | M54410P | I.C. | or SN7400N | 1 |
IC502, 503, 504 | HD7400 | " | 3 | |
D501—509, 511, 518, 519 | 1N34A | Ge. Diode | 12 | |
D510 | RD5.1F(B) | Zener Diode | 1 | |
D512, 514, 515, 516, 517 | 10E1-B | Si. Diode | 5 | |
D513 | RD22EB3 | Zener Diode | 1 | |
CN501 |
QMV5004-011
E43727-002 E40130-001 TAR272448-01 LPSP3008ZS |
Plug Ass'y
Wrapping Tab Tab Heat Sink Screw |
Touch Switch
for X511 for X511 |
1
28 3 1 1 |
SBSB3006V | Screw | for P.W. Board | 4 | |
TAZ000331-02 | Fuse Holder | KD-A5A/B/E ☆ | 4 | |
QMF51A2-1R6BS | Fuse | KD-A5B ☆ | 2 | |
"-1R6 | '' | KD-A5A/E ☆ | 2 |
X51 | E | С | В |
Remot Con.
Rec Muting |
C Tester | 0 | 20,5 | 0 | ON |
C. Tester | 0 | 0 | 0 | OFF |
0 | 20,6 | 0 | ON | |
0 | 0 | 0,7 | OFF |
Ref. No. | Parts No. | Parts Name | Remarks | Q'ty |
---|---|---|---|---|
*VMW4540-002 | P. W. Board | for Remote Control | 1 | |
R51 | QRD142K-223 | C. Resistor | 22 kΩ 1/4 W | 1 |
R52 | ·222 | " | 2.2 kΩ " | | 1 |
R53, 54 | ·'' -562 | " | 5.6 kΩ " | 2 |
X51 | 2SC1684(R,S) | Si. Transistor | 1 | |
D51 | RD4.3E(C) | Zener Diode | 1 | |
D52 | MA150 | Si. Diode | 1 | |
CN52 |
QMV5005-008 | Plug Ass'y | 1 | |
CN51 | ··· -011 | 1 | ||
E43727-002 | Wrapping Tab | 14 | ||
VKL4567-001 | Bracket | for P.W.B. | 1 | |
LPSP3006ZS | Screw | " | 2 | |
SBSB3006V | Tapping Screw | for Bracket | 2 |
△ parts are safety assurance parts.
Other P.W. Board Parts List
When replacing those parts, make sure to use the specified one.
Ref. No. | Parts No. | Parts Name | Remarks | Q'ty |
---|---|---|---|---|
(Timer Switch) | VMW4531-001 | P.W. Board | for Timer Switch | 1 |
(Metal Switch)
S5 R935 R936 |
VMW4533-001
QSS2301-006 QRD146K-390 "-101 |
P.W. Board
Slide Switch Unflamable Resistor |
39 Ω 1/4 W
100 Ω " |
1
1 1 1 |
(Volume)
VR103, 203 |
VMW1522-002B
QVE5A3A-054F |
P.W. Board
Variable Resistor |
for Volume
for Rec. Level |
1 |
(LED Indicator)
D301–306 |
VKS4146-001
VKM4525-002 TLR102 |
LED Holder
P.W. Board LED |
for Indicator
(Red) (Level Indicator x 5, ANRS Indi- cator x 1) |
1
1 6 |
(Control Switch)
S501—506 |
VMW3519-003
QSP0022-002 TLR102 TLG102 VKZ4101-001 |
P. W. Board
Touch Switch LED '' Spacer |
for Control SW.
(Red) Rec. Indicator (Green) Play and Pause Indicators for LED |
1
1 2 3 |
(Connector) |
VMW4523-001
10E1-B QMV5005-006 "-009 VKL3143-001 QRD146K-102 |
P.W. Board
Si. Diode Connector Tab Unflamable Resistor |
1 kΩ 1/4 W |
1
2 1 1 6 1 |
(Switch) |
VMW4522-001
QSP0029-001 QVP5004-004 |
P.W. Board (L)
Slide Switch Connector |
1
2 1 |
|
(Hall Element) |
VMW4530-001
DN6835 QMV5005-003 |
P.W. Board
Hall I.C. Connector |
1 |
DIN P.W Board Parts (KD-A5 B/E)
Ref. No. | Parts No. | Parts Name | Remarks | Q'ty |
---|---|---|---|---|
VMW4544-001 | P.W. Board | 1 | ||
R701, 801 | QRD141K-102 | C. Resistor | 1 kΩ ¼ W | 2 |
R702, 802 | ′′ -332 | 3.3 kΩ ″ | 2 | |
R703, 803, 704, 804 | ′′ -224 | 220 kΩ ″ | 4 | |
R705, 805 | ′′ -222 | " | 2.2 kΩ " | 2 |
R706, 806, 707, 807 | ·' -103 | 10 kΩ ″ | 4 | |
R708, 808 | " | 390 kΩ " | 2 | |
R709, 809 | QRD143K-334 | 330 kΩ " | 2 | |
R710, 810 | ·'' -103 | " | 10 kΩ " | 2 |
R91 | ′′ -332 | " | 3.3 kΩ " | 1 |
C701,801,702,802,703,803
C91 |
QEW41HA-105N
QEW41EA-336N |
E. Capacitor |
1 μF 50 V
33 μF 25 V |
6
1 |
D91 | RD4.3E(C) | Zener Diode | 1 | |
X701, 801, 702, 802 | 2SC1684(R,S) | Si. Transistor | 4 | |
DIN Jack Ass'y | 1 | |||
SDSP2605R | Screw | for DIN Jack | 2 |
Ref. No. | Parts No. | Parts Name | Remarks | Q'ty |
---|---|---|---|---|
1, 2 | VPA3073-00C | Packing Case Ass'y | KD-A5A/B/E/J/U | 1 set |
" | ″ -00D | KD-A5C | 1 set | |
| 1 | VPA3073-005 | Case | KD-A5A/B/E/J/U | 1 |
"-006 | " | KD-A5C | 1 | |
2 | VPH1169-001 | Cushion (L) | 1 | |
VHP1170-001 | " (R) | 1 | ||
TKS000501-01 | Sheet | for Deck | 1 | |
VPK4121-001 | Spacer | for Cassette Door | 1 | |
QPGA060-06005 | Envelope | for Deck | 1 | |
AP4056A-036 | " | for Provided Cord | 1 | |
QPGB024-03404 | " | for Instruction Book | 1 |
Parts No. | Parts Name | Remarks | Q'ty |
---|---|---|---|
VMP0002-00A | PIN Cord | 2 | |
VYA4001-00A | Head Cleaning Stick | 1 | |
VNN0035-301 | Instruction Book | | 1 | |
⊤LJ000476-02 | ANRS Seal | | 1 | |
TLJ00477-02 | Super ANRS Seal | 1 | |
TLJ000443-01 | Seal | Made in Japan, KD-A5B | 1 |
BT20029 | Warranty Card | KD-A5A | 1 |
BT20025C | " | KD-A5C | | 1 |
BT2032 | " | KD-A5J/U for PX | 1 |
BT2023 | Service Procedure | KD-A5J/U for PX | 1 |
QZL1002-003BS | Warning Label | KD-A5B | 1 |
TLT000505-01 | UL/CSA Caution Label | KD-A5C/J | 2 |
BT20024B | Special Reply Card | KD-A5J/U for PX | 1 |
T46328-003 | Caution Label | KD-A5A/B | 1 |
T44362-001 | CSA Mark | KD-A5C | 1 |
T46328-004 | Caution Label | KD-A5E | 1 |
V04062-001 | Siemens Plug | KD-A5U | 1 |
T46328-001 | Caution Label | KD-A5U | 1 |
VND4013-001 | Warning Label | KD-A5A/E | | 1 |
VNC5004-001 | Mark Sticker | KD-A5E | 1 |
E7795-1 | EP. Mark | KD-A5U for PX | 1 |