JVC HV-32P40BU, HV-28P40BU User Manual

HV-32P40BU
HV-28P40BU

ENGLISH

DEUTSCH

FRANÇAIS

NEDERLANDS

CASTELLANO

ITALIANO

PORTUGUÊS

COLOUR TELEVISION

FARBFERNSEHGERÄT
TELEVISEUR COULEUR
KLEURENTELEVISIE
TELEVISOR A COLOR
TELEVISORE A COLORI
TELEVISOR A CORES

INSTRUCTIONS

BEDIENUNGSANLEITUNG

MANUEL D’INSTRUCTIONS

GEBRUIKSAANWIJZING

MANUAL DE INSTRUCCIONES

ISTRUZIONI

INSTRUÇÕES

How to move the TV

When moving the TV, make sure that it is held by two people as shown in the illustration. Be careful
not to trap your hands when putting the TV down.

1

2

ENGLISH

3

1

Thank you for buying this JVC colour television.
To make sure you understand how to use your new TV, please read this manual thoroughly before you
begin.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

• Operate only from the power source specified (AC 220 – 240 V, 50 Hz) on the unit.

• Avoid damaging the AC plug and power cord.

• When you are not using this unit for a long period of time, it is recommended that you disconnect
the power cord from the mains outlet.

Distance recommendations

Avoid improper installation and never position the unit
where good ventilation is impossible.
When installing this TV, distance recommendations
must be maintained between the set and the wall, as well
as inside a tightly enclosed area or piece of furniture.
Keep to the minimum distance guidelines shown for safe
operation.

Failure to take the following precautions may result in damage to the TV or
remote control.

DO NOT block the TV’s ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be
able to get out.)

DO NOT place anything on top of the TV.

(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)

DO NOT allow objects or liquid into the cabinet openings.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

DO NOT place any naked flame sources, such as lighted candles, on the TV.

The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it hard.
Never use any cleaner or detergent on it.

In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it
yourself or remove the rear cover.

D.I.S.T. demonstration

To start the D.I.S.T. demonstration:
Press the H button to display the menu bar. Then press the yellow button.
A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.

To quit the D.I.S.T. demonstration:
Press the yellow button, b button, p p buttons or any of the number buttons.

2

To enjoy even better picture quality

The picture quality of this TV is controlled by a combination of three functions (PICTURE MODE,
DIGITAL VNR, and Super DigiPure).
By adjusting these three functions, you can change the picture quality to suit your preferences. The
initial settings of the three functions are as follows.

PICTURE MODE : BRIGHT

DIGITAL VNR : AUTO(LOW)

Super DigiPure : AUTO

 If you want a sharper picture, change to the following settings.

(However, the picture quality may not change very much if you are already watching a clear
picture.)

PICTURE MODE : BRIGHT

DIGITAL VNR : MIN

Super DigiPure : MAX

 If there is a lot of noise in the picture, change to the following settings.

PICTURE MODE : STANDARD

DIGITAL VNR : AUTO(HIGH)

Super DigiPure : MIN

ENGLISH

Note:

• For detailed information about how to change these settings, see “PICTURE menu” on
page 25.

3

CONTENTS

Setting up your TV ...................................5

Connecting the aerial and video cassette

recorder (VCR) ....................................... 5

Connecting the power cord to the AC

outlet....................................................... 6

Putting the batteries into the remote

control..................................................... 6

Initial settings ............................................. 6

T-V LINK functions..................................... 9

TV buttons and functions......................11

Turn the main power on ........................... 11

Choose a TV channel .............................. 11

Adjust the volume .................................... 11

Remote control buttons and

functions..............................................12

Turn the TV on or off from standby mode
Choose a TV channel and watch images

from external devices ........................... 13

Adjust the volume .................................... 14

Information function ................................. 14

ZOOM function......................................... 15

3D CINEMA SOUND function.................. 16

Return to TV channel instantly................. 16

Using the “Freeze” function...................... 16

Using the “Multi-picture” function ............. 17

Favourite channel function....................... 19

Operating a JVC brand VCR or DVD

player.................................................... 20

.. 12

Teletext function ....................................21

Basic operation ........................................ 21

Using the List Mode ................................. 21

Hold.......................................................... 22

Sub-page ................................................. 22

Reveal...................................................... 22

Size .......................................................... 22

Index ........................................................ 23

Cancel...................................................... 23

Top overview............................................ 23

Subtitle ..................................................... 23

Using the TV’s menu..............................24

Basic operation ........................................ 24

PICTURE menu ......................................25

PICTURE MODE...................................... 25

CONTRAST ............................................. 25

BRIGHT.................................................... 25

SHARP..................................................... 25

COLOUR.................................................. 25

HUE.......................................................... 25

COLOUR TEMP....................................... 25

FEATURES .............................................. 26

SOUND menu ......................................... 29

STEREO / I • II ......................................... 29

BASS........................................................ 29

TREBLE ................................................... 29

BALANCE ................................................ 29

HEADPHONE VOLUME .......................... 29

3D CINEMA SOUND................................ 29

FEATURES menu................................... 30

SLEEP TIMER ......................................... 30

ON TIMER................................................ 30

CHILD LOCK............................................ 31

APPEARANCE......................................... 32

BLUE BACK ............................................. 32

FAVOURITE SETTING ............................ 32

SET UP menu ......................................... 33

AUTO PROGRAM.................................... 33

EDIT/MANUAL ......................................... 33

LANGUAGE ............................................. 37

PICTURE TILT ......................................... 37

DECODER (EXT-2).................................. 37

COMPONENT AUTO SELECT ................ 38

EXT SETTING.......................................... 39

Additional preparation ..........................42

Connecting external equipment ...............42

CH/CC numbers ..................................... 44

Troubleshooting ....................................46

Specifications ........................................49

4

Setting up your TV

Caution

• Turn off all the equipment including the TV before connecting anything.

Connecting the aerial and video cassette recorder (VCR)

• The connecting cables are not provided.

• For further details, refer to the manuals provided with the devices to be connected.

 If you are connecting a VCR,

follow A → B → C in the diagram
opposite.

 If you are not connecting a VCR,

follow 1.

For example

75-ohm
Coaxial

Cable

ENGLISH

Aerial

To use the T-V LINK functions, you must
have a T-V LINK compatible VCR
connected by a SCART cable C to the EXT­2 terminal on the TV. For details about T-V
LINK functions, see “T-V LINK functions”
on page 9.

• You can watch a video using the VCR

without doing C. For details, see your
VCR instruction manual.

• To connect more equipment, please see
“Connecting external equipment” on
page 42.

• To connect additional audio equipment,
see “Connecting speakers/amplifier” on
page 43.

• If you connect a decoder to a T-V LINK
compatible VCR, set the DECODER
(EXT-2) function to ON. For details, see
“DECODER (EXT-2)” on page 37.
Otherwise, you will not be able to watch
scrambled channels.

 Rear Panel

EXT-

4

Y

PrPbR

L

L

AUDIO OUT

R

EXT-1

EXT-3

EXT-2

S

S

Back of the TV

EXT-

21-pin

SCART

Cable

VCR

4

Y

L

PrPbR

L

R

AV IN/OUT

Terminal

AUDIO OUT

EXT-1

EXT-2

S

EXT-3

S

75-ohm
Coaxial

To Aerial

To Aerial

Cable

Input

Output

1 Aerial socket (page 5)
2 EXT-1 terminal (pages 5, 39, 42)
3 EXT-2 terminal (pages 5, 9, 39, 42)
4 EXT-3 terminal (pages 39, 42)
5 EXT-4 terminal (pages 39, 42)
6 AUDIO OUT terminal (page 43)

5

Setting up your TV

s

Connecting the power cord to the AC outlet

Caution

• Operate only from the power source
specified (AC 220 – 240 V, 50 Hz) on
the unit.

• Failure to use the supplied power cord
or to insert it into a correctly earthed
outlet may result in electric shocks.

Putting the batteries into the remote control

Use two AA/R6 dry cell batteries.
Insert the batteries from the - end, making
sure the + and - polarities are correct.

• Follow the warnings printed on the
batteries.

• Battery life is about six months to one
year, depending on how much you use the
remote control.

• The batteries we supply are only for
setting up and testing your TV, please
replace them as soon as you need to.

• If the remote control does not work
properly, replace the batteries.

Initial settings

When the TV is first turned on, it goes into
the initial settings mode, and you will see the
JVC logo. Follow the instructions on the
screen display to make the initial settings.

Yellow button

Blue button

7 button

1 Press the A button on the TV

The power lamp lights green and the JVC
logo appears.

A button Power lamp

• If the JVC logo does not appear this is
because your TV has already been
turned on for the first time:
use the “LANGUAGE” and “AUTO
PROGRAM” functions to make the
initial settings. For details, see “SET
UP menu” on page 33.

6

Setting up your TV

2 Press the a button

The LANGUAGE menu appears.

> LANGUAGE

OK

D0002(E)-EN

3 Press the 6 buttons to choose

ENGLISH. Then press the a
button

The on-screen display will then be in
English.
The COUNTRY menu appears as a sub­menu of the AUTO PROGRAM function.
There are two COUNTRY menus.
Pressing the yellow button changes the
COUNTRY menu as follows:

> COUNTRY

OK

> COUNTRY

OK

D0003-EN

START

MORE

START

MORE

4 Press the 5 and 6 buttons to

choose the country where you are

5 Press the blue button to start the

AUTO PROGRAM function

The AUTO PROGRAM menu appears
and received TV channels are
automatically stored in the programme
numbers (PR).

>> AUTO PROGRAM

CH 28

14%

OK

D0004-EN

• Perform the “ACI function” operation
(see page 8) when “ACI START/ACI
SKIP” is displayed.

• To cancel the AUTO PROGRAM
function:
Press the b button.

After the TV channels have been
registered in the programme
numbers (PR), the EDIT menu
appears

> EDIT

D0038-EN

PR ID
AV
01
02
03
04
05
06
07
08
09

OK

MOVE

BBC1

CH/CC

CH
CH
CH
CH
CH
CH
CC
CC
CC

ID

INSERT

21
22
23
24
25
26
01
02
03

MANUAL

DELETE

• If you want to, you can now edit the
programme numbers (PR) using the
EDIT/MANUAL function. For details,
see “EDIT/MANUAL” on page 33.

• If you do not want to edit programme
numbers (PR), go to the next step.

ENGLISH

7

Setting up your TV

6 Press the a button to display the

T-V LINK menu

T-V LINK

DOWNLOAD TV RECORDING DEVICE

OK

D0005

EXIT

-EN

If you do not have a T-V LINK
compatible VCR connected:

Press the b button to exit the T-V LINK
menu.
The T-V LINK menu disappears.

If you have a T-V LINK compatible
VCR connected to the EXT-2
terminal:

Follow the operating procedure
“Downloading the data to VCR” on
page 9 to transmit the Programme number
(PR) data.

Now, the initial settings are complete,
and you can watch the TV

• If your TV can detect the TV channel
name from the TV channel broadcast
signal, the TV channel name is assigned
to the programme number (PR) to which
the TV channel has been set. However,
which TV channels are set to which
programme numbers (PR) will depend on
the area in which you live.

• If a TV channel you want to view is not
set to a programme number (PR), you can
set it using the MANUAL function. For
details, see “EDIT/MANUAL” on
page 33.

• The AUTO PROGRAM function does not
set the programme number PR 0 (AV) for
your video cassette recorder. You will
need to set this using the MANUAL
function.

 ACI function

This TV has an ACI function which decodes
the ACI (Automatic Channel Installation)
data.
Using the ACI function allows all TV
channels transmitted from the cable TV
station to be properly registered quickly
according to the data from the cable TV
station.

If “ACI START/ACI SKIP” appears in
the AUTO PROGRAM menu:

You can use the ACI (Automatic Channel
Installation) function to decode the ACI data
and complete the registration of all the TV
channels in a short period of time.

Press the 6 buttons to choose ACI
START. Then press the a button to
start the ACI function

Depending on your cable TV station, there
may be a broadcast selection menu set up by
the cable TV station.
Follow the menu instructions and use the
5 and 6 buttons to operate the menu.
After you have made the setting, press the
a button.

• If you have any questions about the items
in the Broadcast Selection menu or how to
operate the menu, please contact your
cable TV station.

• If you do not want to use the ACI
function, press the 6 buttons to choose
ACI SKIP and then press a.

• When the cable TV broadcast reception is
poor, the ACI function will not work
properly.

• If there is an error in the ACI data itself,
the TV channel cannot be registered
properly. If this happens, turn the ACI
function off (ACI SKIP) and use the
AUTO PROGRAM function.
Alternatively, use the EDIT/MANUAL
function to correct the Programme
number (PR) setting.

8

Setting up your TV

If “ACI ERROR” is displayed in the
AUTO PROGRAM menu:

“ACI ERROR” means that the ACI function
is not working properly. Press the 2 button
to start the ACI function again.
If “ACI ERROR” still appears even after you
have tried to start the ACI function several
times, press the 3 button to start the AUTO
PROGRAM function. It does not cause any
problem because all the TV channels are
registered to the Programme numbers (PR)
by the AUTO PROGRAM function.

 Downloading the data to VCR

You can transmit to the latest Programme
numbers (PR) data to a VCR with the T-V
LINK function.

Caution

• This only works when a T-V LINK
compatible VCR is connected to the
EXT-2 terminal.

• This only works when the T-V LINK
menu is being displayed.

T-V LINK

DOWNLOAD TV RECORDING DEVICE

OK

D0005

1 Turn on the VCR

2 Press the a button

The data transmission begins.

TV RECORDING DEVICE

TRANSFER. . . . .

D0037

The T-V LINK menu disappears once the
data transmission ends.

When the T-V LINK menu is
changed over to another menu:

The TV has finished its menu. This new
menu is operated from the VCR. See the
VCR instruction manual for what to do
next.

EXIT

-EN

-EN

If “FEATURE NOT AVAILABLE”
appears at the T-V LINK menu:

Check the following three items. Then
press the 2 button to retry data
transmission.

• Has a T-V LINK compatible VCR
been connected to the EXT-2
terminal?

• Has the VCR power been turned on?

• Does the SCART cable that is
connected to the EXT-2 terminal to T­V LINK compatible VCR have all its
proper connections?

T-V LINK functions

When you have a T-V LINK compatible
VCR connected to the EXT-2 Terminal on
the TV, it is easier to set up the VCR and to
view videos. T-V LINK uses the following
features:

To use T-V LINK functions:

A “T-V LINK compatible VCR” means a
JVC video cassette recorder with the T-V
LINK logo, or with one of the following
logos. However, these VCRs may support
some or all of the features described earlier.
For details, see your VCR instruction
manual.

“Q-LINK” (a trademark of Panasonic
Corporation)
“Data Logic” (a trademark of Metz
Corporation)
“Easy Link” (a trademark of Phillips
Corporation)
“Megalogic” (a trademark of Grundig
Corporation)
“SMARTLINK” (a trademark of Sony
Corporation).

ENGLISH

9

Setting up your TV

 Pre-set download

The VCR will automatically download the
registered data on the TV channels from the
TV. This means you do not need to set up the
program channels on your VCR manually.
The preset download function automatically
begins when the initial setting is complete or
whenever you carry out the AUTO
PROGRAM or EDIT/MANUAL functions.

You can also carry out this function using
your VCR controls.

When “FEATURE NOT AVAILABLE” is
displayed:

If “FEATURE NOT AVAILABLE” is
displayed, the download was not performed
correctly. Before trying to download again,
check that:

• the VCR power is turned on

• the VCR is T-V LINK compatible

• the VCR is connected to the EXT-2
terminal

• the SCART cable is fully wired.

 Direct Rec

“What You See Is What You Record”
You can easily record to VCR the images

that you are watching on the TV.
For details, read the manual for your VCR.

Use your VCR controls. “DEVICE IS
RECORDING” is displayed.

In the following situations, the VCR
will stop recording if the TV is turned
off, if the TV channel or input is
changed, or if the menu is displayed
on the TV:

• when recording images from an external
device connected to the TV (for example
a camcorder)

• when recording a TV channel after it has
been unscrambled on a decoder

• when recording a TV channel by using the
TV’s output because the VCR’s own
tuner cannot properly receive that
channel.

You cannot carry out Direct Rec using your
TV’s control.
Generally, the VCR cannot record a TV
channel that it cannot receive properly on its
own tuner, even if you can view that TV
channel on the TV. However, some VCRs
can record a TV channel by using the TV’s
output if that channel can be viewed on the
TV. For details, see your VCR instruction
manual.

When the VCR is not ready, the following
messages are displayed.

ERROR
MESSAGE

NO
RECORDING

NO
RECORDING
POSSIBLE

NO
RECORDING,
MEDIA
PROBLEM

NO
RECORDING,
DEVICE BUSY

Cause and
countermeasure

The VCR is not able to
record.
Check the VCR.

The TV input is set to EXT-4.
Since the EXT-4 picture
cannot be output to EXT-2,
DIRECT REC is not possible.

The recording device is not
ready to record. Check the
VCR tape.

The recording device cannot
record as it is recording or
playing. Check the VCR.

Refer to the VCR instruction manual.

10

TV buttons and functions

Turn the main power on

Press the A button on the TV.

The power lamp lights red and your TV is in
the standby mode.

• If the power lamp lights green, the TV is

To turn the main power off:

Press the A button again.
The power lamp goes off.

Caution

•The A button on the TV does not fully

isolate the TV from the AC supply. If you
are not going to use the TV for a long
period, be sure to disconnect the AC plug
from the AC socket.

Choose a TV channel

Press the P p buttons to choose a
programme number (PR) or an EXT
terminal

Adjust the volume

already on.

ENGLISH

S

R

/

MONO

L

EXT-5

P

R

L

/

MONO

EXT-5

P

S

See the pages in brackets for details.

1 A (main power) button (pages 6, 11)
2 Power lamp (pages 6, 11)
3 Remote control sensor
4 r (Volume) button (page 11)
5 P p buttons/ q buttons (page 11)
6 Headphone jack (mini jack) (page 42)
7 EXT-5 terminal (pages 39, 42)

1 Press the r (Volume) button once

The volume level indicator appears.

2 Press the q buttons while the

volume level indicator is displayed

11

Remote control buttons and functions

1 Muting button
2 Number buttons
3 Information button

1

2

3

4
5

6

7
8

9

0

­=

~

!

@
#

$
%

^
&

*

(

4 c button
5 i button
6 b button
7 7 buttons
8 g (Text) button
9 p p buttons
0 VCR/DVD/Teletext control buttons

- p buttons
= d (Favourite) button
~ # (Standby) button
! VCR/TV/DVD switch
@ G button
# Colour buttons
$ X (Multi) button
% f/g (Freeze/Swap) button
^ H button
& a button
* b button
( r (Volume) q buttons

Turn the TV on or off from standby mode

Press the # (standby) button to turn
the TV on or off

When the TV is turned on, the power lamp
changes from red to green.

• The power can be turned on by pressing

the b button, p p buttons or Number
buttons.

12

To turn the TV on or off, set the VCR/TV/
DVD switch on the remote control to the
TV position and press the # button.
If the VCR/TV/DVD switch on the remote
control is set to a position other than TV,
the TV will not be turned on or off even if
the # button is pressed.

Remote control buttons and functions

Choose a TV channel and watch images from external devices

 Use the number buttons:

Enter the programme number (PR)
of the channel using the number
buttons.

Example:

•PR 6 → press 6

• PR 12 → press 1 and 2

 Use the p p buttons:

Press the p p buttons to
choose the programme number
(PR) you want or an EXT terminal.

 Use the AV button:

Press the AV button to choose an
EXT terminal.

TV mode EXT modes

Programme

numbers

PR 1 – PR 99

EXT-1

EXT-5

or

• You can choose a video input signal
from the S-VIDEO signal (Y/C signal)
and regular video signal (composite
signal). For details, see “S-IN (S­VIDEO input)” on page 39.

• If you do not have a clear picture or no
colour appears, change the colour
system manually. See “COLOUR
SYSTEM” on page 27.

• If you choose an EXT terminal with no
input signal, the EXT terminal number
becomes fixed on the screen.

E3

EXT-2

or

EXT-3

or

EXT-4

S3

• This TV set has a function which can
automatically change over the input
according to a special signal output
from an external device. (The EXT-4
and EXT-5 terminals do not support
this function.)

• Since this TV is designed to make full
use of the resolution of the original
video source, the motion may appear
unnatural when the video source is
input with 625p progressive-scanning
component signals.
If this happens, change the output
setting of the connected device to 625i
interlace-scanning component signal
output. See the instructions that came
with the device for more information.

To return to a TV channel:

Press the b button, the 6 buttons or the
number buttons.

To use the programme number PR 0
(AV):

When the TV and VCR are connected only
by the aerial cable, choosing the programme
number PR 0 (AV) allows you to view
images from the VCR. Set the VCR RF
channel to the programme number PR 0
(AV) manually. For details, see “EDIT/
MANUAL” on page 33.
Pressing the G button changes the choice as
follows:

TV mode

Programme

numbers

PR 1 – PR 99

PR 0

EXT modes

EXT-1

EXT-5

or

E3

EXT-2

or

EXT-3

or

EXT-4

S3

ENGLISH

13

Remote control buttons and functions

• The VCR sends its playback image along
the aerial cable as an RF (radio frequency)
signal.

• Also see your VCR instruction manual.

Adjust the volume

Press the r q buttons to adjust
the volume.

The volume level indicator appears and the
volume changes as you press the r q
buttons.

 Muting the sound

Press the l (muting) button to
turn off the sound.

Pressing the l (muting) button again
restores the previous volume level.

Information function

You can see the channel number of the
programme you are watching, the current
time or the PR LIST.
From the PR LIST, you can choose a channel
or EXT terminal.

Press the h (Information) button to
display the information you want to

see.

Pressing the h (Information) button changes
the display as follows:

PR LIST

D0011-EN

PR ID

AV
01
02
03
04
05
06
07
08
09

OK

BBC1

+10-10

Channel number display

12 : 00

No indication

Channel number display:

The channel number and channel name
(when the channel name is registered) of the
programme you are watching or the EXT
terminal number is displayed.

Time display:

The current time of the teletext data is
displayed.
If the TV has not received a TV channel that
has teletext programmes since it was turned
on, the time display is blank. To view the
current time, choose a TV channel that has
teletext programmes.

• An incorrect current time is sometimes
displayed when watching videos.

PR LIST:

The programme number (PR) and EXT
terminal list is displayed.
Pressing the a button after choosing the
programme number (PR) or EXT terminal
with the 7 buttons will display the
chosen programme or EXT terminal.

• For programme numbers (PR) for which
the CHILD LOCK function is set, the n
(CHILD LOCK) mark is displayed. For
details see “CHILD LOCK” on page 31.

• For programme numbers (PR) which is
registered as a favourite channel, the d
(favourite) mark is displayed. For details
see “Favourite channel function” on
page 19.

14

Remote control buttons and functions

ZOOM function

You can change the screen size according to
the picture aspect ratio. Choose the optimum
one from the following ZOOM modes.

AUTO:

When a WSS (Wide Screen Signalling)
signal, which shows the aspect ratio of the
picture, is included in the broadcast signal or
the signal from an external device, the TV
automatically changes the ZOOM mode to
16:9 ZOOM mode or FULL mode according
to the WSS signal.
If a WSS signal is not included, the picture is
displayed according to the ZOOM mode set
with the 4:3 AUTO ASPECT function.

• For details of the 4:3 AUTO ASPECT
function, see “4:3 AUTO ASPECT” on
page 28.

• When the AUTO (WSS) mode does not
function correctly due to poor WSS signal
quality or when you want to change the
ZOOM mode, press the c button
and change to another ZOOM mode.

REGULAR:

Use to view a normal picture (4:3 aspect
ratio) as this is its original shape.

PANORAMIC:

This stretches the left and right sides of a
normal picture (4:3 aspect ratio) to fill the
screen, without making the picture appear
unnatural.

• The top and bottom of the picture are
slightly cut off.

14:9 ZOOM:

This zooms up the wide picture (14:9 aspect
ratio) to the upper and lower limits of the
screen.

16:9 ZOOM:

This zooms up the wide picture (16:9 aspect
ratio) to the full screen.

16:9 ZOOM SUBTITLE:

This zooms up the wide picture (16:9 aspect
ratio) with subtitles to the full screen.

FULL:

This uniformly stretches the left and right
sides of a normal picture (4:3 aspect ratio) to
fill the wide TV screen.

• For 16:9 aspect ratio pictures that have
been squeezed into a normal picture (4:3
aspect ratio), use the FULL mode to
restore the picture to its original shape.

 Choose the ZOOM mode

1 Press the c button to display

the ZOOM menu

ZOOM

AUTO
REGULAR
PANORAMIC
14:9 ZOOM
16:9 ZOOM
16:9 ZOOM SUBTITLE
FULL

OK

D0009-EN

2 Press the 6 buttons to choose a

ZOOM mode. Then press the a
button

The picture expands and the chosen
ZOOM mode is displayed in about 5
seconds.

• The ZOOM mode may be
automatically changed by the control
signal from an external device. When
you want to return to the previous
ZOOM mode, choose the ZOOM
mode again.

ENGLISH

15