JVC HR-S6700EU, HR-S6711EU Instruction Manual

Page 1
VIDEO CASSETTE RECORDER
ENGLISH
CONTENTS
SAFETY FIRST 2
INDEX 4
INSTALLING YOUR NEW RECORDER 8
Basic Connections ........................................ 8
S-VIDEO Connection .................................... 9
INITIAL SETTINGS 10
Auto Set Up ................................................10
Preset Download ........................................ 12
Language .................................................... 14
SAT CONTROL SET 15
Satellite Receiver Control Setting ................ 15
T-V LINK 17
T-V Link Functions ...................................... 17
PLAYBACK 18
Basic Playback ............................................ 18
Playback Features .......................................19
RECORDING 23
Basic Recording .......................................... 23
Recording Features ..................................... 24
B.E.S.T. Picture System ...............................27
TIMER RECORDING 28
S
HOWVIEW
Express Timer Programming ........................ 30
Automatic Satellite Programme
Recording ................................................... 34
EDITING 35
Edit From A Camcorder ..............................35
Output/Input Set ......................................... 36
Edit To Or From Another Video
Recorder ..................................................... 38
SYSTEM CONNECTIONS 40
Connecting To A Satellite Receiver .............40
Connecting/Using A Decoder ..................... 42
Connecting/Using A Stereo System ............. 43
SUBSIDIARY SETTINGS 44
Mode Set .................................................... 44
Tuner Set .................................................... 48
Video Channel Set ......................................54
S
HOWVIEW
Clock Set .................................................... 56
TROUBLESHOOTING 58
QUESTIONS AND ANSWERS 61
SPECIFICATIONS 62
LIST OF TERMS 63
®
Timer Programming ................28
®
Setup ...................................... 55
LPT0325-001A
LPT0325-001A
LPT0325-001ALPT0325-001A
EN
Page 2
2
EN
SAFETY FIRST
Safety Precautions
The rating plate and the safety caution are on the rear of the unit.
WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
CAUTION
When you are not using the recorder for a long period of time, it is recommended that you disconnect
8
the power cord from the mains outlet. Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric
8
shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial.
WARNING
There are two different types of SECAM colour systems: SECAM-L, used in FRANCE (also called SECAM-West), and SECAM-B, used in Eastern European countries (also called SECAM-East).
1. This recorder can also receive SECAM-B colour television signals for recording and playback.
2. Recordings made of SECAM-B television signals produce monochrome pictures if played back on a video recorder of SECAM-L standard, or do not produce normal colour pictures if played back on a PAL video recorder with SECAM-B system incorporated (even if the TV set is SECAM-compatible).
3. SECAM-L prerecorded cassettes or recordings made with a SECAM-L video recorder produce monochrome pictures when played back with this recorder.
4. This recorder cannot be used for the SECAM-L standard. Use a SECAM-L recorder to record SECAM-L signals.
IMPORTANT
Please read the various precautions on page 2 and 3 before installing or operating the recorder.
8
It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without
8
the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein.
Cassettes marked “S-VHS” and “VHS” can be used with this video cassette recorder. However, S-VHS recordings are possible only with cassettes marked “S-VHS”. By using the S-VHS ET function, it is possible to record and play back with S-VHS picture quality on VHS cassettes with this recorder.
S
HOWVIEW
from Gemstar Development Corporation.
is a registered trademark of Gemstar Development Corporation. The S
HOWVIEW
system is manufactured under licence
Page 3
For Italy:
“It is declared that this product, brand JVC, conforms to the Ministry Decree n. 548 of 28 Aug.’95 published in the Official Gazette of the Italian Republic n. 301 of 28 Dec.’95”
EN
3
The STANDBY/ON operating current on and off. “
Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a single-speed video recorder.
Failure to heed the following precautions may result in damage to the recorder, remote control or video cassette.
1. DO NOT place the recorder . . .
...in an environment prone to extreme temperatures or humidity. ...in direct sunlight. ...in a dusty environment. ...in an environment where strong magnetic fields are generated. ...on a surface that is unstable or subject to vibration.
2. DO NOT block the recorder’s ventilation openings.
3. DO NOT place heavy objects on the recorder or remote control.
4. DO NOT place anything which might spill on top of the recorder or remote control.
5. AVOID violent shocks to the recorder during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form in the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the recorder turned on for a few hours to let the moisture dry.
button does not completely shut off mains power from the unit, but switches
1
“ shows electrical power standby and “!“ shows ON.
`
Page 4
4
EN
FRONT VIEW
* Attach the provided connector cover when you do not use the front panel connectors.
INDEX
STANDBY/ON
A
Time r
B
REVIEW Button 墌pg. 20
C
Cassette Loading Slot
D
SP/LP Button 墌pg. 23
E
Play
F
SHUTTLE Ring 墌pg. 18
G
S-VIDEO Input Connector 墌pg. 35
H
VIDEO/AUDIO Input Connectors 墌pg. 35
I
PR +/– Buttons 墌pg. 23
J
Button 墌pg. 29, 31
#
Button 墌pg. 18
4
Button 墌pg. 10
1
REAR VIEW
S-VHS ET Button 墌pg. 25
K
SAT
L M N O P Q
R
Button 墌pg. 34
#
Front Display Panel 墌pg. 5 Infrared Beam Receiving Window Record Pa us e << button on the remote control 墌pg. 19, 21 Stop/Eject
Button 墌pg. 23
7
Button 墌pg. 19
9
and 6 >> Buttons — same as w e
2
Button 墌pg. 18
0
Mains Power Cord 墌pg. 8
A
S OUT Connector 墌pg. 9
B
AV1 (L-1) IN/OUT Connector 墌pg. 8, 38, 40,
C
41, 42 ANT. IN Connector 墌pg. 8
D
AUDIO OUT (L/R) Connectors 墌pg. 43
E
AV2 (L-2) IN/DECODER Connector 墌pg. 15,
F
38, 40, 41, 42 SAT CTL Connector 墌pg. 15
G
RF OUT Connector 墌pg. 8
H
Page 5
FRONT DISPLAY PANEL
VPS/PDC
EN
5
B.E.S.T. Picture System Display 墌pg. 27
A
Symbolic Mode Indicators
B
STILL:
u
SLOW:
RECORD:
RECORD PAUSE:
PLAY: FF/REW VARIABLE SEARCH:
Tape Speed Indicators 墌pg. 23
C
* EP is for NTSC playback only.
ui o oi
Programme Time Indicators 墌pg. 30
D
“Timer” Indicator 墌pg. 29, 31
E
Tape Remaining Time Indicator 墌pg. 25
F
Channel/Clock Display 墌pg. 13
G
Instant REVIEW Indicator 墌pg. 20
H
VPS/PDC Indicator 墌pg. 29, 31
I
S-VHS Indicator 墌pg. 25, 47
J
VCR Indicator 墌pg. 24
K
“Cassette Loaded” Mark
L
Counter/Remain Display
M
Mode Display (L-1, L-2, F-1, S-1 or SAT*)
N
* When “L-2 SELECT” is set to “SAT” (墌pg. 37), “SAT” appears
instead of “L-2”.
Page 6
6
EN
ON-SCREEN DISPLAY
When “O.S.D.” is set to “ON” (墌pg. 45), various operational indicators appear on the TV screen.
INDEX (cont.)
Operation Mode Indicators
A
Tape Speed SP/LP/EP
B
* EP is for NTSC playback only.
Tape Direction
C
Counter Display
D
Tape Remaining Time Indicator 墌pg. 25
E
Audio Mode Display 墌pg. 22
F
Tape Position Indicator
G
The tape position indicator appears on the TV screen when you press
5 from the Stop mode
or perform an Index Search (
pg. 21). The position of
q” in relation to “0”
(beginning) or “+” (end) shows you where you are on the tape.
3 or
Beginning End
NOTE:
Depending on the type of tape used, the tape position indicator may not appear correctly.
Type of Broadcast 墌pg. 26
H
Current Day/Month/Year
I
Clock Display
J
Channel Position Number and Station Name/
K
Auxiliary Input Indicator (L-1, L-2, F-1, S-1 or SAT*)
* When “L-2 SELECT” is set to “SAT” (墌pg. 37), “SAT” appears
instead of “L-2”.
Timer Warning Display
L
A warning appears on the TV screen to tell you that the timer-recording is to start in 5 minutes if you’re not in the Timer mode at that time. The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press
“Cassette Loaded” Mark
M
& on the remote control.
Page 7
EN
7
REMOTE CONTROL
Rewind
K
Record
L
Stop
M N O
8
MENU Button 墌pg. 14
Button 墌pg. 10
r t
Button 墌pg. 18, 20
3
Button 墌pg. 23
7
Button 墌pg. 18, 23
TV PR +/– Button 墌“Operating JVC TVs” below STANDBY/ON
P
AUDIO Button 墌pg. 22
Q
(TV Muting) Button 墌“Operating JVC TVs”
^
Button 墌pg. 10
1
below Display – – : – – Button 墌pg. 25
R
DAILY Button 墌pg. 29, 31
S
WEEKLY Button 墌pg. 29, 31
T
AUX Button 墌pg. 35
U
Time r
V
DATE +/– Button 墌pg. 30
W
PR +/– Button 墌pg. 23
X
Auto Tracking
Y
Button 墌pg. 29, 31
#
Button 墌pg. 21
p
SP/LP Button 墌pg. 23 30 SEC Button 墌pg. 20
Z
Play
a b c d e
Button 墌pg. 18
4
Fast Forward Pa us e
Button 墌pg. 19
9
Button 墌pg. 18, 20
5
OK Button 墌pg. 11
Button 墌pg. 19, 21
w e
TV
+/– Button 墌“Operating JVC TVs” below
%
Buttons with a small dot on the left side of the name can also be used to operate your JVC TV while holding down the TV button. (
This remote control transmits A code signals only; it is not applicable to B code signals.
TV Button 墌“Operating JVC TVs” in the right
A
“Operating JVC TVs” in the right column)
column TV/VCR Button 墌pg. 24 and “Operating JVC
B
TVs” in the right column REVIEW Button 墌pg. 20
C
NUMBER Keys 墌pg. 23, 28
D
VPS/PDC Button 墌pg. 29, 31
E
Cancel
F
Button 墌pg. 32
&
0000 Button 墌pg. 25 STOP +/– Button 墌pg. 30
G
START +/– Button 墌pg. 30
H
PROG Button 墌pg. 28
I
Programme Check
J
Button 墌pg. 32
"
How To Use
The remote control can operate most of your video recorder’s functions, as well as basic functions of JVC TV sets. (
“Operating JVC TVs” below)
Point the remote control toward the receiving window.
The maximum operating distance of the remote control is
about 8 m.
Operating JVC TVs
To operate your TV, while holding down the TV button, press the corresponding button:
+/–
%
TV
, ^ (TV Muting).
1,
TV/VCR, TV PR
+/–,
NOTES:
When inserting the batteries, be sure to insert in the correct directions as indicated under the battery cover.
Depending on the type of JVC TV, some or all functions may not be operated using the remote control.
If the remote control doesn’t work properly, remove its batteries, wait a short time, replace the batteries and then try again.
Page 8
8
EN
Basic Connections
Aerial connector
Back of TV
21-pin SCART connector
21-pin SCART cable (not provided)
Mains power cord
RF cable
(provided)
TV aerial cable
INSTALLING YOUR NEW RECORDER
It’s essential that your video recorder be properly connected.
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.
Check the contents.
A
Make sure the package contains all of the accessories listed in “SPECIFICATIONS” on page 62.
Situate the recorder.
B
Place the recorder on a stable, horizontal surface.
Connect the recorder to TV.
C
The connection method you use depends on the type of TV you have.
RF Connection
8 To connect to a TV with NO AV input connectors . . .
Disconnect the TV aerial cable from the TV.
A
Connect the TV aerial cable to the ANT. IN connector
B
on the rear panel of the recorder. Connect the provided RF cable between the RF OUT
C
connector on the rear panel of the recorder and the TV’s aerial connector.
Back of recorder
AV1 (L-1) IN/OUT
Mains outlet
Make AV connection if your TV has a 21-pin AV input connector (SCART) in order to reduce the possibility of interference. With AV connection, you can enjoy stereo playback of video tapes if you are using a stereo TV.
AV C onnection
8 To connect to a TV with AV input connectors . . .
Connect the aerial, recorder and TV as per “RF
A
Connection”. Connect an optional 21-pin SCART cable between the
B
AV1 (L-1) IN/OUT connector on the rear panel of the recorder and the TV’s 21-pin SCART connector.
Connect the recorder to mains.
D
Plug the end of the mains power cord into a mains outlet.
After the connection is completed, perform “Auto Set Up” on page 10.
Page 9
S-VIDEO Connection
EN
9
Back of TV
Aerial connector
Mains power
AUDIO IN connectors
S-VIDEO IN connector
Mains outlet
cord
Back of recorder
S OUT
S-Video cable (not provided)
AUDIO OUT
Audio cable (not provided)
RF cable (provided)
TV ariel cable
To connect to a TV with S-VIDEO/AUDIO IN
8
connectors . . .
Connect the recorder to TV.
A
Connect the aerial, recorder and TV as per “RF
A
Connection” ( Connect the recorder’s S OUT connector to the TV’s
B
S-VIDEO IN connector. Connect the recorder’s AUDIO OUT connectors to the
C
TV’s AUDIO IN connectors.
Connect the recorder to mains.
B
Plug the end of the mains power cord into a mains outlet.
pg. 8).
NOTES:
You can obtain high-quality S-VHS pictures.
With S-VIDEO connection, you cannot use the Preset
Download function (
If your TV is not stereo-capable, use the recorder’s AUDIO OUT connectors to connect to an audio amplifier for Hi-Fi stereo sound reproduction. (
To operate the recorder with your TV using the S-VIDEO connection, set your TV to its AV mode.
For switching the TV’s mode, refer to the instruction manual of your television.
After the connection is completed, perform “Auto Set Up” on page 10.
pg. 12).
pg. 43)
Page 10
10
EN
Auto Set Up
Auto Channel Set/Auto Clock Set/ Auto Guide Program Number Set
After the pressed for the first time to power on the recorder selecting your country*, the Auto Set Up function sets the tuner channels, clock** and Guide Program numbers automatically.
* If you live in Belgium (BELGIUM) or Switzerland (SUISSE), you also
**If you live in Hungary (MAGYARORSZÁG), Czech Republic
1 button on the recorder or remote control is
need to select your language.
ESKÁ REPUBLIKA), Poland (POLSKA) or other countries in
(
C
Eastern Europe (OTHER EASTERN EUROPE), set the clock manually.
, by simply
INITIAL SETTINGS
Before starting, make sure of the following:
The TV aerial cable should be connected to the recorder.
The recorder’s mains power cord should be connected to a
mains outlet.
If you want to use the on-screen display, the TV should be set to its AV mode (with AV or S-VIDEO connection
pg. 8, 9) or UHF channel 36 (with RF connection
pg. 8).
Turn on the recorder.
A
Press 1 on the recorder or remote control. The Country Set display appears on the front display panel and/or on the TV screen.
NOTE:
If you have connected your TV to the recorder with RF connection and the on-screen display appearing on UHF channel 36 looks distorted, perform “Video Channel Set” on page 54.
International Telephone Country Code
ÖSTERREICH
32
BELGIUM
C
ESKÁ REPUBLIKA DAN MARK DEUTSCHLAND ESPAÑA GREECE ITALIA MAGYARORSZÁG NEDERLAND NORGE
: : : : : : : : : :
POLSKA
42
PORTUGAL
45
SUISSE
49
SUOMI
34
SVERIGE
30
РОССИЯ
39 36
OTHER WESTERN EUROPE
31
OTHER EASTERN EUROPE
47
Select your country.
B
On the front display panel
Press
to select your international telephone country
rt
code of your country referring to the chart in the left column.
(Example) DEUTSCHLAND is selected.
On the on-screen display
Press
to move the
rt
highlight bar (pointer) to your country’s name.
NOTES:
If you have selected BELGIUM (32) or SUISSE (41), go to step .
3
If you have selected MAGYARORSZÁG (36),
43
:
48
:
351
:
41
:
358
:
46
:
07
:
– –
:
EE
:
REPUBLIKA (42), POLSKA (48) or OTHER EASTERN EUROPE (EE), press OK. The Clock Set screen appears. Set the clock manually (
If you have selected any other country name (code), go to step .
4
pg. 56), then go to step 4.
C
ESKÁ
Page 11
Select the language.
Beginning End
C
Press OK. The Language Set display appears on the front display panel and/or on the TV screen.
On the front display panel
Press
Language Code
ENGLISH DEUTSCH FRANCAIS ITALIANO CASTELLANO NEDERLANDS SVENSKA
(Example) DEUTSCH is selected for SUISSE.
to select your language code.
rt
NORSK
01
: : : : : : :
International telephone country code
02 03 04 05 06 07
SUOMI DAN SK POLSKI
CEc
MAGYAR
ЯЗЫК
TINA
Language code
08
:
09
:
10
:
11
:
12
:
13
:
14
:
On the on-screen display
Press
to move the
rt
highlight bar (pointer) to the language of your choice.
EN
11
If you are using the on-screen
display, the AUTO SET screen will appear. As Auto Set Up progresses, the “ mark on the TV screen moves from left to right. When the Auto Set Up is completed, “SCAN COMPLETED” appears for about 5 seconds, then the normal screen appears.
If you have connected the recorder to your TV via the AV
connection ( Preset Download (
q
pg. 8), the recorder will automatically perform
pg. 12) instead of the Auto Set Up.
ATTENTION
Once you have performed Auto Set Up, even if the recorder’s memory backup has expired, all the stored stations and their Guide Program numbers remain in the recorder’s memory and the recorder will not perform Auto Set Up again. You only need to set the clock. ( If you have moved to a different area, perform each setting as required.
Video channel setting (for RF connection users)
Tuner setting
Clock setting
If a new station starts broadcasting in your area, perform tuner setting ( setting (
pg. 48
pg. 56
pg. 48) and, if necessary, video channel
pg. 54).
pg. 56)
pg. 54
Perform Auto Set Up.
D
Press OK. The AUTO SET/T-V LINK display appears on the front display panel and/or on the TV screen.
On the front display panel
Press
to select “Auto” and press OK or e.
rt
On the on-screen display
Press
to move the
rt
highlight bar (pointer) to “AUTO SET” and press OK or
.
e
“Auto” blinks on the front display panel; do NOT press any button on the recorder or remote control until the front display panel shows clock time, “(CH) 1” or
” as illustrated on page 13.
– –:– –
NOTES:
In the area where no TV station transmits a PDC (Programme
Delivery Control) signal, the recorder can perform neither Auto Clock Set nor Auto Guide Program Number Set.
If there is a power cut, or if you press
Set Up is in progress, Auto Set Up will be interrupted; be sure to turn off the recorder power once and try again from step 1.
Auto Clock Set may not function properly depending on the
reception condition.
If no sound accompanies the picture or the audio sounds
unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels (
pg. 51, “INFORMATION”).
1 or
MENU
while Auto
Page 12
12
EN
Preset Download
Auto Channel Set by Downloading from TV/Auto Clock Set/Auto Guide
INITIAL SETTINGS (cont.)
If you have connected the recorder to your TV via the AV connection ( Preset Download instead of the Auto Set Up in step 4 on page
11. After downloading, the recorder sets the clock and Guide
Program numbers automatically.
Perform steps 1 to 3 of “Auto Set Up” on page 10 before continuing.
pg. 8), the recorder will automatically perform
Program Number Set
ATTENTION
You can use this function only with a TV offering T-V Link, etc.* Be sure to use a fully-wired 21-pin SCART cable.
* Compatible with TVs offering T-V Link, EasyLink, Megalogic,
SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.
Perform Preset Download.
A
Press OK. The AUTO SET/T-V LINK display appears on the front display panel and/or on the TV screen.
On the front display panel
Press
On the on-screen display
Press highlight bar (pointer) to “T-V LINK” and press OK or
e
If you are using the on-screen
If you press any button on the
to select “CH – –” and press OK or e.
rt
to move the
rt
.
Preset positions on the front display panel increase from “CH1”; do NOT press any button on the recorder or remote control until the front display panel shows clock time, “(CH) 1” or “– –:– –” as illustrated on page 13.
display, the T-V LINK screen will appear. Then the GUIDE PROG SET screen will appear during Guide Program Number Set. When Preset Download is completed, “COMPLETED” appears for about 5 seconds, then the normal screen appears.
recorder or remote control while downloading is in progress, it will be interrupted.
NOTES:
For details, refer to the instruction manual of your TV.
In the area where no TV station transmits a PDC (Programme
Delivery Control) signal, the recorder can perform neither Auto Clock Set nor Auto Guide Program Number Set.
If there is a power cut, or if you press downloading or set up is in progress, it will be interrupted; be sure to turn off the recorder power once and try again from the beginning.
Auto Clock Set may not function properly depending on the reception condition.
On this recorder, the characters available for station names (ID) are A–Z, 0–9, –, downloaded stations may differ from those of your TV (
pg. 52).
f, + and I (space). Some names of
1 or
MENU
while
Set the video channel.
B
Set the video channel to off manually. (墌pg. 54)
Page 13
EN
Results of Auto Set Up/Preset Download appear on the front display panel
If both Auto Channel Set and Auto Clock Set have been performed successfully, the correct current time is displayed.
Turn on the TV and select its video channel or AV mode, then make sure that all necessary stations have been stored in the recorder’s memory by using the PR button(s).
If station names (ID – will be displayed at the top left corner of the TV screen for about 5 seconds when the recorder is tuned to a different station.
If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 50 – 53.
If Auto Channel Set has succeeded but Auto Clock Set has not, “1” (channel position) is displayed.
Turn on the TV and select its video channel or AV mode, then make sure that all necessary
A
stations have been stored in the recorder’s memory by using the PR button(s).
If station names (ID – will be displayed at the top left corner of the TV screen for about 5 seconds when the recorder is tuned to a different station.
If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 50 – 53.
Perform “Clock Set” on page 56.
B
If both Auto Channel Set and Auto Clock Set have failed, “– –:– –” is displayed.
Make sure the cables are connected properly and turn off the recorder’s power once, then turn the recorder’s power back on again. The Country Set display appears on the front display panel and/or on the TV screen; perform “Auto Set Up” on page 10 or “Preset Download” on page 12 again.
pg. 53) have also been stored in the recorder’s memory, the station name
pg. 53) have also been stored in the recorder’s memory, the station name
13
IMPORTANT
To check if the Guide Program numbers have been set correctly, perform the S
In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not work
properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the S system, the recorder will record a TV programme of a different station. When programming the timer using the S system, be sure to check the desired channel is selected correctly (
Your video recorder memorizes all detected stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture (
pg. 51, “Delete A Channel”).
HOWVIEW
pg. 28, “S
Timer Programming (墌pg. 28).
®
HOWVIEW
Timer Programming”).
HOWVIEW HOWVIEW
INFORMATION
Language for the on-screen display
Auto Set Up also selects the language automatically for the on-screen display depending on the Country setting you have made in step 2 on page 10 (unless you have selected BELGIUM or SUISSE), as shown below.
SUOMI PORTUGAL DEUTSCHLAND POLSKA NORGE SVERIGE
If you want to change the language setting manually, see “Language” on page 14.
Just Clock
Your recorder is equipped with the Just Clock function which provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. If you want to take advantage of this function, simply set it to “ON” (
pg. 56, “Just Clock”).
SUOMI DANMARK
]
ENGLISH ÖSTERREICH
]
DEUTSCH
]
POLSKI ITALIA
]
NORSK MAGYARORSZÁG]MAGYAR OTHER EASTERN EUROPE]ENGLISH
]
SVENSKA ESPAÑA
]
C
ESKÁ REPUBLIKA
DANSK NEDERLAND
]
DEUTSCH GREECE
]
CEc
TINA РОССИЯ
]
ITALIANO OTHER WESTERN EUROPE]ENGLISH
]
CASTELLANO
]
] ] ]
NEDERLANDS ENGLISH
ЯЗЫК
Page 14
14
EN
Language
Turn on the TV and select the video channel (or AV mode).
INITIAL SETTINGS (cont.)
This recorder offers you the choice to view on-screen messages in 14 different languages. Though Auto Set Up selects the language automatically (墌pg. 13), you can change the language setting manually as required.
Access the Main Menu screen.
A
Press
B
Press rt to move the highlight bar (pointer) to “AUTO CH SET”, then press
or
OK
C
Press rt to move the highlight bar (pointer) to your country’s name, then press OK or
.
MENU
Access the Country Set screen.
.
e
Select your country.
.
e
Select the language.
D
Press highlight bar (pointer) to the language of your choice.
You do not have to press OK;
E
Press
to move the
rt
pressing OK enters AUTO SET/ T-V LINK screen.
Return to the normal screen.
.
MENU
Page 15
SAT CONTROL SET
Satellite Receiver Control Setting
EN
The following procedure is required if you receive satellite channels through a satellite receiver. Approximately 20 seconds before the S programming ( (
pg. 30) starts, the recorder sets its input mode to “L-2”
and automatically switches the satellite receiver’s channels using the provided Satellite Controller.
pg. 28) or Express timer programming
HOWVIEW
15
timer
Your recorder
21-pin SCART
cable
(not provided)
Transmitter
Satellite receiver
Satellite receiver
Satellite Controller (suggested locations)
Satellite Controller
Installing Satellite Controller
Situate the Satellite Controller.
A
Place the Satellite Controller so that the path between its transmitter and the satellite receiver’s remote sensor is unobstructed.
Attach the Satellite Controller.
B
Fix securely using the adhesive strip attached on the back of the Satellite Controller.
Make connections.
C
Be sure to connect the recorder’s AV2 (L-2) IN/DECODER connector to the satellite receiver’s 21-pin SCART connector.
NOTE:
When connecting your satellite receiver, refer to its instruction manual.
Connect the Satellite Controller to recorder.
D
Connect the Satellite Controller to the SAT CTL connector on the rear panel.
AV2 (L-2) IN/DECODER
Back of recorder
SAT CTL
Page 16
16
EN
SAT CONTROL SET (cont.)
Access the Initial Set screen.
C
Press rt to move the highlight bar (pointer) to “INITIAL SET”, then press OK or
Access the Sat Control Set screen.
D
Press rt to move the highlight bar (pointer) to “SAT CONTROL SET”, then press OK or
E
Press the appropriate
NUMBER
brand code from the list on page 17, then press OK.
If the brand code you entered is invalid, the code field will be reset. Enter the correct brand code again.
If the recorder is in playback or recording mode, you cannot set the brand code.
.
e
Enter the satellite receiver’s brand.
keys to enter the
.
e
Setting satellite receiver's brand and channel
After installation, set the satellite receiver’s brand and channel correctly; otherwise, the Satellite Controller cannot work correctly.
Turn on the TV and select the video channel (or AV mode).
Turn on the satellite receiver.
A
Turn on the satellite receiver’s power.
Access the Main Menu screen on the
B
recorder.
Press
MENU
.
Select the satellite receiver’s channel for
F
testing.
Press the appropriate
NUMBER
of the channel positions on the satellite receiver, then press OK.
You can select the channel position between 1 to 999.
After pressing OK, the recorder enters the Test mode.
keys to enter one
Page 17
SAT CONTROL SET (cont.) T-V LINK
Check the result of the test.
G
If the satellite receiver’s channel number has been changed to the same one as you set in step 6 ...
Press bar (pointer) to “CHANGED TO ...”, then press OK or finish the Sat Control Set mode.
If the satellite receiver’s channel number has not been changed correctly ...
Press CHANGED”, then press OK or procedure again from step 5.
BRAND NAME CODE
JVC AMSTRAD CANAL SATELLITE CANAL + D-BOX ECHOSTAR ECHOSTAR (VIA DIGITAL) FINLUX FORCE GALAXIS GRUNDIG HIRSCHMANN ITT NOKIA JERROLD KATHREIN LUXOR MASCOM MASPRO NOKIA PACE PANASONIC PHILIPS RFT SAGEM SALORA SIEMENS SKYMASTER TPS TRIAX WISI
to move the highlight
rt
to
e
to move the highlight bar (pointer) to “NOT
rt
. Then perform the
e
73 60, 61, 62, 63, 92 81 81 85 78, 79, 80 82 68 89 88 64, 65 64, 78 68 75 70, 71 68 93 70 87 65, 67, 74, 86, 92 74 66, 84 69 83 68 64 69 83 91 64
EN
17
T-V Link Functions
When you connect the recorder to your TV via a fully-wired 21-pin SCART cable ( available. You can use these functions only with a TV offering T-V Link, etc.* For details, refer to the instruction manual of your TV.
* Compatible with TVs offering T-V Link, EasyLink, Megalogic,
SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.
NexTView Link
You can download the EPG (Electronic Programme Guide) information from your TV for timer-programming on the recorder. For details, refer to the instruction manual of your TV.
TV Auto Power On
The TV will turn on and be set to its AV mode automatically whenever you play a tape. For details, refer to the instruction manual of your TV.
VCR Auto Standby
You can use your TV’s remote control to turn off the recorder. For details, refer to the instruction manual of your TV.
Direct Rec
You can easily start recording the programme that you are watching on your TV. When you use this function, set “DIRECT REC” to “ON” (
pg. 8), the following functions are
pg. 45).
NOTES:
The Satellite Controller may not work with all types of satellite receiver.
For some satellite receivers, you need to set its channel input mode to 2-digit.
If your satellite receiver has more than two channel modes, be sure to set to “All Channel Mode”. For details, refer to the instruction manual of the satellite receiver.
When selecting the satellite receiver’s channel ( signals from the remote control may interfere with signals transmitted from the Satellite Controller. In this case, move the remote control as close to the recorder’s infrared beam receiving window as possible.
step 6),
Page 18
18
EN
Basic Playback
Turn on the TV and select the video channel (or AV mode).
PLAYBACK
Load a cassette.
A
Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointed toward the recorder.
Don’t apply too much pressure when inserting.
The recorder’s power comes on automatically and the counter
is reset to “0:00:00”.
If the record safety tab has been removed, playback begins automatically.
Find the programme start point.
B
If the tape is advanced past the start point, press 3 or turn the
5
C
Press 4. “BEST” appears blinking in the recorder’s front display panel during automatic tracking. (
D
Press 8 on the remote control or front panel. Then press
SHUTTLE
or turn the
Start playback.
Stop playback.
ring to the left. To go forward, press
SHUTTLE
ring to the right.
on the recorder’s
0
to remove the cassette.
0
pg. 27)
Clean the video heads using a dry cleaning cassette — TCL-2UX — when:
Rough, poor picture appears while a tape is played back.
The picture is unclear or no picture appears.
“USE CLEANING CASSETTE” appears on the screen (only
with “O.S.D.” set to “ON” (
pg. 45)).
Usable cassettes
Compact VHS camcorder recordings can be played on this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.
This video recorder can record on regular VHS and Super VHS cassettes. While only VHS signals can be recorded on regular VHS cassettes*, both VHS and Super VHS signals can be recorded and played back using Super VHS cassettes.
* By using the S-VHS ET function, it is possible to record and
play back with S-VHS picture quality on VHS cassettes with this recorder.
Page 19
Playback Features
NOTE:
Refer to the
SHUTTLE
illustration on the right as you read the following procedures.
ring
EN
19
Still Picture/Frame-By-Frame Playback
1
Pause during playback.
Press 9.
If there is vertical jitter, use the PR buttons to correct the picture.
2
Activate Frame-by-frame playback.
Press 9.
OR
Press w or e (2 or 6).
Slow Motion
During playback or still, turn the right for forward slow motion, or to the left for reverse slow motion (refer to the illustration on the left).
OR
During still picture, press and hold 9 for 2 seconds, then release. Press and release again to return to still picture.
OR
During still picture, press and hold w or e (2 or 6). Release to return to still picture.
SHUTTLE
ring to the
ATTENTION
Picture may not appear during high-speed search with an LP-recorded tape.
In the high-speed search, still, slow motion or frame-by-frame playback mode, the picture will be distorted, and there will be a loss of colour.
Variable Speed Search
During playback or still, turn the right for forward variable-speed search, or to the left for reverse variable-speed search (refer to the illustration on the left).
OR
During playback, press w or e (2 or 6).
The more times you press, the faster the playback picture moves.
To decrease speed, press the button for the opposite direction.
To resume normal playback, press 4.
SHUTTLE
ring to the
Page 20
20
EN
PLAYBACK (cont.)
High-Speed (Turbo) Search
During playback or still, turn the way to the right for forward high-speed search, or to the left for reverse high-speed search. Releasing ring resumes still picture playback.
For forward high-speed search, turn the way to the right and release it within 1 second.
For reverse high-speed search, turn the way to the left and release it within 1 second.
SHUTTLE
OR
During playback or still, press 5 for forward high-speed search, or
for reverse high-speed search.
3
NOTE:
For short searches, press and hold 5 or 3 for over 2 seconds during playback or still picture. When released, normal playback resumes.
To resume normal playback, press 4.
ring all the
SHUTTLE
SHUTTLE
SHUTTLE
ring all the
ring all the
Instant ReView
Simply by pressing a single button, the recorder power comes on, rewinds, and begins playback of the last timer-recorded programme. If you have several programmes recorded, you can easily access any of them.
Skip Search
During playback, press unwanted sections. Each press initiates a 30-second period of fast-motion playback. Normal playback resumes automatically.
To resume normal playback, press 4.
1 to 4 times to skip over
30 SEC
NOTE:
Before starting, make sure that the recorder is off and that the Timer mode is disengaged.
Activate Instant ReView.
Press
REVIEW
recorder searches for the index code indicating the start of the last timer-recorded programme. Once it’s found, playback begins automatically.
The front display panel tells you how many programmes have been timer-recorded. If you have, for example, 3 programmes, “REVIEW” and “3” appear and blink. To watch the first of the 3 programmes, press and begins playback automatically. You can access a programme as far as 9 index codes away from the current tape position.
Instant ReView is not possible while the recorder is in the Timer mode.
The number of recorded programmes will not be displayed on the front display panel after Automatic Satellite Programme Recording (
. The recorder power comes on and the
REVIEW
pg. 34).
three times
. The recorder searches
Page 21
EN
21
Index Search
Your recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction.
NOTE:
Before starting, make sure the recorder is in the Stop mode.
Activate Index Search.
Press w or e (2 or 6). “2 1” or “6 1” is displayed on the TV screen and search begins in the corresponding direction.
To access index codes 2 through 9, press until the correct index number is displayed.
Example:
To locate the beginning of B from the current position, press twice. To locate the beginning of D from the current position, press once.
Current position
When the specified index code is located, playback begins automatically.
w or e repeatedly
Index number
Next Function Memory
The Next Function Memory “tells” the recorder what to do after rewinding. Before continuing, make sure the recorder is in the Stop mode.
For Automatic Start Of Playback
a-
Press For Automatic Power Off
b-
Press 3, then press 1 within 2 seconds. For Automatic Timer Standby
c-
Press 3, then press # (
, then press 4 within 2 seconds.
3
TIMER
) within 2 seconds.
Manual Tracking
Your video recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the PR buttons.
w
e
1
Override automatic tracking.
Press p on the remote control.
2
Adjust the tracking manually.
Press PR + or –.
3
Return to automatic tracking.
Press p on the remote control.
NOTE:
When a new tape is inserted, the recorder enters the automatic tracking mode automatically.
Page 22
22
EN
PLAYBACK (cont.)
Repeat Playback
Your recorder can automatically play back the whole tape 100 times repeatedly.
1
Start playback.
Press 4.
2
Activate Repeat Playback.
Press 4 and hold for over 5 seconds, then release.
The Play indicator ( slowly.
After playing back a tape 100 times, the recorder stops automatically.
3
Stop Repeat Playback.
Press 8 at any time.
Pressing
4, 3, 5 or 9 also stops Repeat Playback.
u) on the front display panel blinks
Soundtrack Selection
Your video recorder is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select.
During Playback
Pressing as follows:
on the remote control changes the soundtrack
AUDIO
TRACK
On-Screen Display
HI FI
j h
L
R
HI FI
j
L
HI FI
h
R
NORM For audio-dubbed tapes
HI FI
NORM
For Hi-Fi stereo tapes
For main audio of Bilingual tapes
For sub audio of Bilingual tapes
For audio-dubbed tapes
USE
NOTES:
“HI FI L
For instructions on recording stereo and bilingual programmes,
“O.S.D.” must be set to “ON” or the on-screen displays will
j h R“ should normally be selected. In this mode,
Hi-Fi stereo tapes are played back in stereo, and the normal audio track is played back automatically for tapes with only normal audio.
refer to page 26.
not appear (
pg. 45).
Page 23
RECORDING
Basic Recording
Turn on the TV and select the video channel (or AV mode).
EN
23
Load a cassette.
A
Insert a cassette with the record safety tab intact.
The recorder’s power comes on automatically and the counter is reset to “0:00:00”.
Choose a programme.
B
Press you wish to record.
C
Press recorder’s front display panel to confirm the selected tape speed.
D
Press and hold 7 and press 4 on the remote control, or press
B.E.S.T. takes place at the beginning of both the first SP and the first LP recording after inserting the cassette. (
PR +/–
or the
NUMBER
keys to select the channel
Set the tape speed.
(p). Check the SP/LP indicator on the
SP/LP
Start recording.
on the recorder.
7
pg. 27)
Recording Resume Function
If there is a power outage during recording, Instant Timer Recording ( recording will resume automatically when power is restored to the recorder unless the recorder’s memory backup has expired.
pg. 24) or timer recording (墌pg. 28, 30), the
If “DIRECT REC” is set to “ON”, the programme that appears on the TV screen will be recorded (
Pause/Resume recording.
E
Press 9. Press 4 to resume recording.
Stop recording.
F
Press 8 on the remote control or Then press
to remove the cassette.
0
pg. 45).
on the recorder.
0
Accidental erasure prevention
To prevent accidental recording on a recorded cassette, remove its safety tab. To record on it later, cover the hole with adhesive tape.
Record safety tab
Page 24
24
EN
Recording Features
RECORDING (cont.)
Instant Timer Recording (ITR)
This easy method lets you record for from 30 minutes to 6 hours (selectable in 30-min. increments), and shuts the recorder off after recording is finished.
1
Start recording.
Press 7 on the recorder.
2
Engage the ITR mode.
Press 7 again. “o” blinks and “0:30” appears on the front display panel.
3
Set the recording duration.
If you want to record for more than 30 minutes, press 7 to extend the time. Each press extends recording time by 30 minutes.
NOTE:
You can only perform ITR using the 7 button on the recorder’s front panel.
Record One Programme While Watching Another
If your recorder is connected to the TV via the AV connection, press and the TV broadcast being recorded disappear. Once recording is in progress, all you need to do is to set the channel controls on the TV for the station you wish to view.
The programme selected with the TV’s channel controls appears on the TV screen, while the one selected with the recorder’s PR buttons is recorded on the tape.
If a decoder is connected to the recorder ( select a scrambled channel as well with the TV channel controls.
TV/VCR
. The recorder’s VCR indicator
pg. 42), you can
Page 25
EN
25
Elapsed Recording Time Indication
1
Set the counter display.
Press display panel.
2
Reset the counter.
Press
The counter is reset to “0:00:00” and shows the exact elapsed time as the tape runs. You can check the exact time of a recording or playback.
until a counter reading appears on the front
– –:– –
before starting recording or playback.
0000
Tape Remaining Time
Press
The front display panel shows the tape remaining time with “
y” displayed.
By pressing the show the counter reading, channel position*, clock time or tape remaining time.
* Channel position is not displayed during playback.
NOTE:
Depending on the type of tape used, the tape remaining time reading may not appear right away, or is not correct. “– –:– –” may sometimes appear, or the display may blink on occasion.
until the time remaining on the tape appears.
– –:– –
button, you can change the display to
– –:– –
Super VHS ET (S-VHS ET) — Recording on VHS cassettes with
S-VHS quality
You can record in SP mode on VHS cassettes with S-VHS picture quality. Tapes recorded using this function can be played back on a recorder equipped with the S-VHS ET function.
You can activate the S-VHS ET function only before you start recording on a VHS cassette.
Before recording, make sure that “B.E.S.T.” is set to “ON”. (
pg. 45)
Engage the S-VHS ET mode.
Press
S-VHS ET
The S-VHS indicator lights up on the front display panel.
To disengage the S-VHS ET mode, press
light goes off.
NOTES:
You cannot activate the S-VHS ET function ... ... while recording is in progress. ... while timer-recording or Instant Timer Recording (
pg. 24) is in progress.
... while B.E.S.T. (
The S-VHS ET function does not work ... ... with S-VHS cassettes. ... with recordings in LP mode.
To keep the highest quality recording and playback pictures over a long period of time, S-VHS recording on S-VHS cassettes is recommended.
Use of high grade tapes is recommended for S-VHS ET recordings. On some tapes, picture quality will not improve even if the S-VHS ET function is used. Check the recording quality before you start important recordings.
You can play back a tape recorded using the S-VHS ET function on most of S-VHS recorders and of VHS recorders equipped with SQPB (S-VHS QUASI PLAYBACK) function. (Notice some recorders are not compatible with the S-VHS ET function.)
While playing back a tape recorded using the S-VHS ET function on some recorders, noise may appear. (If playback picture becomes blurred or interrupted, use a cleaning cassette.)
In the high-speed search, still, slow-motion or frame-by-frame playback mode ( mode are performed frequently on a tape recorded using the S-VHS ET function, the tape may be damaged and the picture may be deteriorated.
on the recorder. The button lights up.
S-VHS ET
pg. 27) is in progress.
pg. 19, 20), noise may appear. If these
. The button’s
Page 26
26
EN
RECORDING (cont.)
Receiving Stereo and Bilingual Programmes
Your recorder is equipped with a Sound-Multiplex decoder (A2) and a Digital stereo sound decoder (NICAM) making reception of stereo and bilingual broadcasts possible. When the channel is changed, the type of broadcast being received will be displayed on the TV screen for a few seconds.
Type of Broadcast Being Received
A2 Stereo A2 Bilingual Regular Monaural NICAM Stereo NICAM Bilingual NICAM Monaural
To listen to a stereo programme, press “HIFI L
To listen to a bilingual programme, press
To listen to the standard (Regular Monaural) audio while
jhR” appears on the TV screen.
“HIFI L
j” or “HIFI h R” appears on the TV screen.
receiving a NICAM broadcast, press appears on the TV screen.
On-screen Display
ST BIL. (none) ST NICAM BIL. NICAM NICAM
AUDIO
AUDIO
AUDIO
until
until
until “NORM”
NOTE:
“O.S.D.” must be set to “ON” or the on-screen displays will not appear (
To Record Stereo and Bilingual Programmes (A2)
Stereo programmes are automatically recorded in stereo on the Hi-Fi audio track (with the normal audio track recording mixed L and R channel sound).
Bilingual programmes are automatically recorded in bilingual on the Hi-Fi audio track. The main soundtrack will be recorded on the normal audio track.
To Record NICAM Stereo and Bilingual Programmes
The NICAM audio programme will be recorded on the Hi-Fi audio track, and the Standard audio programme will be recorded on the normal audio track.
pg. 45).
NOTES:
If the quality of stereo sound being received is poor, the broadcast will be received in monaural with better quality.
Before playing back a programme recorded in stereo, or a bilingual programme, refer to “Soundtrack Selection” on page
22.
Page 27
B.E.S.T. Picture System
The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during playback and recording, and compensates to provide the highest-possible playback and recording pictures. You can set “B.E.S.T.” to “ON” or “OFF” to your preference (
pg. 45).
Playback
The recorder assesses the quality of the tape once you initiate playback.
The recorder adjusts the playback picture quality based on the quality of the tape in use.
B.E.S.T. is active during Auto Tracking. “BEST” appears blinking on the recorder’s front display panel.
NOTES:
When watching a tape recorded with “B.E.S.T.” set to “ON”, it is recommended that you leave B.E.S.T. on during playback as well.
When watching a rental tape or one recorded on another video recorder, or when using this recorder as the player for editing, set B.E.S.T. to your preference (
“BEST” only appears at the beginning of automatic tracking. Even though it doesn’t appear after that, the B.E.S.T. function is operative.
pg. 45).
EN
27
Recording
The recorder assesses the quality of the tape once you initiate recording.
DURING B.E.S.T.
B.E.S.T. COMPLETE
The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording.
NOTES:
The B.E.S.T. system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.
The B.E.S.T. system does not work while Automatic Satellite Programme Recording is in progress (
In the case of timer recordings, the B.E.S.T. system works before recording is initiated.
Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re-performed.
Pressing the recorder’s does not start Instant Timer Recording (
7 button while “BEST” is displayed
ATTENTION
Since the B.E.S.T. system works before recording actually starts, there is a delay of approximately 7 seconds after and
4 on the remote control are pressed, or 7 on the
recorder is pressed. To make sure you record the desired scene or programme in its entirety, first perform the following steps:
Press and hold
A
Pause mode.
The recorder then automatically checks the condition of the tape and, after approximately 7 seconds, re-enters Record Pause.
Press
B
If you want to bypass the B.E.S.T. system and begin recording immediately, set “B.E.S.T.” to “OFF” (
4 to start recording.
9 and press 7 to engage the Record
pg. 34).
pg. 24).
pg. 45).
7
Page 28
28
EN
TIMER RECORDING
®
S
HOWVIEW
Timer
Programming
Before performing the S Programming:
Make sure that the recorder’s built-in clock is set properly.
Insert a cassette with the safety tab in place. The recorder
will come on automatically.
Turn on the TV and select the video channel (or AV mode).
HOWVIEW
Tim er
With the S simplified because each TV programme has a corresponding code number which your recorder is able to recognize.
A
Press
The front display panel looks like this:
B
Press the enter the S of a programme you wish to record.
If you make a mistake, press
HOWVIEW
Access the S
PROG
Enter the S
NUMBER
and input the correct number.
system, timer programming is greatly
screen.
number.
&
.
HOWVIEW
HOWVIEW
HOWVIEW
keys to
number
The S
HOWVIEW
panel with only a 4-digit number:
C
Press OK, then the S
HOWVIEW
appears (if you’re just starting out, “P1” appears).
The front display panel shows the programme start time. Pressing
" changes the display to the programme stop time, then the
date and channel position.
IMPORTANT
Make sure the channel position number you wish to record is displayed; if not, see “S the Guide Program number correctly.
If the number you entered is invalid, “ERROR” appears on the TV screen and “Err” appears on the front display panel. Press
& and input a valid S
If the “GUIDE PROG SET” screen appears, see “ATTENTION” on page 29.
number you enter appears on the front display
Access the S
Program screen
HOWVIEW
HOWVIEW
HOWVIEW
Program screen.
®
Setup” on page 55 and set
number.
Page 29
EN
29
Set the tape speed.
D
Press
E
Press
If “VPS/PDC ON” is displayed on the TV screen or “VPS/PDC” is lit on the front display panel, VPS/PDC is set to ON.
If “VPS/PDC OFF” is displayed on the TV screen or “VPS/PDC” is not lit on the front display panel, VPS/PDC is set to OFF.
F
Press on the TV screen for about 5 seconds, then the normal screen appears. If “PROGRAM OVERLAPPED” appears on the TV screen and “Err” on the front display panel, see page 33.
Repeat steps 1 – 6 for each additional programme.
G
Press # ( and “
To disengage the timer mode, press
(p).
SP/LP
Set the VPS/PDC mode.
VPS/PDC
“VPS/PDC Recording” on page 31.
to select “ON” or “OFF”.
Return to the normal screen.
or OK. “PROGRAM COMPLETED” appears
PROG
Engage the recorder’s timer mode.
). The recorder turns off automatically
TIMER
” appears on the front display panel.
#
# (
TIMER
) again.
NOTES:
To Change The Stop Time . . . . . . press compensate for anticipated programme schedule delays.
To Timer-Record Weekly Or Daily Serials . . . . . . after pressing OK in step 3, press “9”) for weekly serials or serials (Monday — Friday). Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the button again makes the corresponding indication disappear.
You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, “PROGRAM FULL” appears on the TV screen and “FULL” appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (
It is not possible to timer-record a TV programme with a S
HOWVIEW
STOP +/–
number which starts with “0”.
after pressing OK in step 3. You can
WEEKLY (NUMBER
DAI LY (NUMBER
pg. 32).
key “8”) for daily
key
Satellite Receiver Users
To timer-record a satellite broadcast using the S system:
A Perform “Satellite Receiver Control Setting” on page 15. B Perform steps 1 – 7. In step 3, the front display panel
shows “L2” for the channel position. In step 5, you cannot set “VPS/PDC” to “ON”.
C Leave the satellite receiver’s power on.
HOWVIEW
ATTEN TION
Guide Program Number Set
“GUIDE PROG SET” appears after performing step 3 if the Guide Program number for the S entered has not been set. If you want to set the Guide Program number for the satellite broadcast station, press the PROG” to “SAT”. Press number on which your recorder or satellite receiver receives that station, then press OK or number. The S
HOWVIEW
HOWVIEW
NUMBER
rt to input the channel position
e to set the Guide Program
Program screen appears.
(Example) To timer-record a ZDF programme with the S
HOWVIEW
* If your recorder receives ZDF on the channel position 2, press OK or
e
number you
key “0” to change “TV
system.
after entering “2”.
Page 30
30
EN
TIMER RECORDING (cont.)
Express Timer Programming
Before performing Express Timer Programming:
Make sure that the recorder’s built-in clock is set properly.
Insert a cassette with the safety tab in place. The recorder
will come on automatically.
Turn on the TV and select the video channel (or AV mode).
If you don’t know the S wish to record, use the following procedure to set your recorder to timer-record the programme.
Access the S
A
Press
B
Press just starting out, “P1” appears.)
The front display panel looks like this:
C
Press time you want recording to start.
Press and hold move in 30-minute increments, or press and release repeatedly to move 1 minute at a time.
.
PROG
Access the Programme screen.
START+/–
Enter the programme start time.
START+/–
HOWVIEW
. (If you’re
to enter the
START+/–
number for the programme you
HOWVIEW
screen.
to
The front display panel looks like this:
Enter the programme stop time.
D
Press
STOP+/–
stop.
Press and hold press and release repeatedly to move 1 minute at a time.
E
Press
DATE+/–
The current date appears on the TV screen. The date you enter appears in its place.
to enter the time you want recording to
STOP+/–
to move in 30-minute increments, or
Enter the programme date.
.
Page 31
EN
31
Enter the channel position.
F
Press
G
Press
H
Press
If “VPS/PDC ON” is displayed on the TV screen or “VPS/PDC” is lit on the front display panel, VPS/PDC is set to ON.
If “VPS/PDC OFF” is displayed on the TV screen or “VPS/PDC” is not lit on the front display panel, VPS/PDC is set to OFF.
I
After confirming all information is correct, press
. “PROGRAM COMPLETED” appears on the TV
OK
screen for about 5 seconds, then the normal screen appears. If “PROGRAM OVERLAPPED” appears on the TV screen and “Err” on the front display panel, see page
33.
Repeat steps 1 – 9 for each additional programme.
J
Press # ( and “
To disengage the timer mode, press
.
PR+/–
Set the tape speed.
(p).
SP/LP
Set the VPS/PDC mode.
VPS/PDC
“VPS/PDC Recording” in the right column
to select “ON” or “OFF”.
Return to the normal screen.
Engage the recorder’s timer mode.
). The recorder turns off automatically
TIMER
” appears on the front display panel.
#
# (
TIMER
) again.
PROG
or
Satellite Receiver Users
To timer-record a satellite broadcast using Express Timer Programming:
A Perform “Satellite Receiver Control Setting” on page 15. B Perform steps 1 – 10. In step 6, press the
“0” to change “TV PROG” to “SAT”. The front display panel shows “L2” for the channel position. Then press
to enter the channel position for the satellite
PR+/–
broadcast. In step 8, you cannot set “VPS/PDC” to “ON”.
C Leave the satellite receiver’s power on.
NUMBER
key
VPS/PDC Recording
Now available from some TV stations, PDC (Programme Delivery Control) and VPS (Video Programme System) are service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed.
NOTES:
When you use Express Timer Programming, set the start time (VPS or PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.
VPS/PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 (L-2) IN/ DECODER on your recorder.
VPS/PDC recording is also possible via the AV1 (L-1) IN/ OUT connector.
How to check if the station being received transmits a VPS/PDC signal
A Press
front display panel.
B Hold down
“VPS/PDC” appears blinking on the front display panel. If a VPS/PDC signal is detected from the station, “VPS/ PDC” will stop blinking. If no VPS/PDC signal is detected from the station, “VPS/ PDC” will blink at a slower rate.
C Press
until the channel position appears on the
– –:– –
for about 5 seconds.
START+
– –:– –
or
again to return to normal display.
START+
To Timer-Record Weekly Or Daily Serials . . .
. . . anytime during steps 2 through 9, press key “9”) for weekly serials or serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the button again makes the corresponding indication disappear.
DAILY (NUMBER
WEEKLY (NUMBER
key “8”) for daily
NOTE:
You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, “PROGRAM FULL” appears on the TV screen and “FULL” appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (
pg. 32).
Page 32
32
EN
TIMER RECORDING (cont.)
Access the Programme screen/display.
C
Press " again to check more information. Each time you press ", the next programme’s information appears.
The front display panel shows the programme start time. Pressing
changes the display to the programme stop time, then the
OK
date and the channel position.
To cancel or change a programme...
Cancel or change a programme.
D
Press & to cancel a programme. To change programme settings, press the appropriate button:
STOP+/ –, DATE +/–, PR+/–, VPS/PDC
You can change “TV PROG” to “SAT” for the channel position by pressing the
NUMBER
key “0”.
START+/–
and/or
,
SP/LP
(p).
Check, cancel and change programmes
Disengage the timer mode.
A
Press # (
Access the Programme Check screen/display.
B
Press ".
), then press 1.
TIMER
Return to the normal screen/display.
E
Press " as many times as necessary. If there are still some programmes remaining, go on to step 6.
Return to the timer mode.
F
Press # (
TIMER
).
NOTE:
You can also check the programmes on the front display panel even if the recorder’s power is off (unless the recorder is in the Power Save mode mode; however, it is not possible to cancel or change the programmes.
pg. 46) or the recorder is in the Timer
Page 33
EN
33
When programmes overlap each other
If “PROGRAM OVERLAPPED” appears, you have another programme overlapping the programme you have just made. The Programme Check screen appears and conflicting programmes will start blinking.
Example: Programme 1 (you have just made) and Programme 4 overlap each other.
Confirm the overlapping programmes.
A
Overlapping programmes blink on the TV screen.
Select the programme to modify.
B
Press rt, then press OK or e.
You can only select one of the overlapping programmes.
NOTE:
If you do not mind this overlap, press programme setting. The programme with the lower programme number will be recorded and the other one will not be recorded correctly. If no changes are made for approximately 1 minute, the recorder will return to the normal screen.
Cancel or change programme setting.
C
To cancel a programme,
screen you do not want is shown. “PROGRAM COMPLETED” appears on the TV screen for about 5 seconds, then the normal screen appears.
To change a programme, START+/–, STOP+/–, DATE+/–, PR+/–, VPS/PDC
(
SP/LP
want to make changes is shown, then press OK. “PROGRAM COMPLETED” appears on the TV screen for about 5 seconds, then the normal screen appears.
) when the Programme screen on which you
p
press & when the Programme
press the appropriate button:
to finish the timer
PROG
and/or
NOTE:
If the overlap is not yet solved, or another overlap occurs with the timer programme setting after making the last correction on a programme, the conflicting programmes will be shown on the Programme Check screen again. Repeat the above steps again until the overlap is solved.
Page 34
34
EN
Automatic Satellite Programme Recording
This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder’s AV2 (L-2) IN/DECODER connector and programme the timer on the satellite receiver. The recorder starts or stops recording by the signals input from the satellite receiver. After recording, the recorder’s power shuts off automatically.
TIMER RECORDING (cont.)
ATTEN TION
Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver’s power is turned on.
If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Automatic Satellite Programme Recording mode; otherwise, the recorder will start recording when the connected appliance’s power is turned on.
Automatic Satellite Programme Recording and timer­recording cannot be done at the same time.
Before performing the following steps:
Make sure the satellite receiver is connected to the recorder’s AV2 (L-2) IN/DECODER connector. (
41)
Programme the timer on the satellite receiver.
Insert a cassette with the safety tab in place.
Select the L-2 SELECT mode.
A
Set “L-2 SELECT” to “A/V” or “SAT” (墌pg. 37).
When you select “SAT”, refer to “IMPORTANT” on page 40.
Set the tape speed.
B
Press
SP/LP
(p).
pg. 40,
Engage the Automatic Satellite Programme
C
Recording mode.
Press and hold lights up and the recorder turns off automatically.
for about 2 seconds. The button
SAT#
NOTES:
To disengage the Automatic Satellite Programme Recording mode, press
If the recorder’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.
In step 3, if the SAT
Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer Programming” (
* Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.
The SAT
For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.
Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.
Pressing the recorder’s
If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible
Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may
If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not
You can also record a programme from your cable system in the same way if the system has a timer.
The B.E.S.T. system (
Just Clock (
When the Automatic Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Automatic Satellite
After Automatic Satellite Programme Recording, the number of recorded programmes will not be displayed on the front display
# button blinks while Automatic Satellite Programme Recording is in progress.
disengages the Automatic Satellite Programme Recording mode.
to set different tape speeds for each programme.
record slightly longer than the actual length of the programme.
start Automatic Satellite Programme Recording even though the SAT is turned back on again, the recorder starts recording.
Programme Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON”.
panel for the Instant ReView function (
# button does not light but instead blinks quickly even though your satellite receiver’s power is off, Automatic
pg. 30) to timer-record a satellite programme.
1 button while Automatic Satellite Programme Recording is in progress turns off the recorder’s power and
pg. 27) does not work while Automatic Satellite Programme Recording is in progress.
pg. 56) does not work when the Automatic Satellite Programme Recording mode is engaged.
pg. 20).
#. The button’s light goes off.
SAT
# button blinks. When the satellite receiver shuts off once and
Page 35
EDITING
Edit From A Camcorder
A
If the camcorder has no S-VIDEO output connector ...
Your recorder
VIDEO input
Video cable (not provided)
AUDIO input
Audio cable (not provided)
VIDEO OUT
EN
35
You can use a camcorder as the source player and your recorder as the recorder.
Make connections.
A
A
If the camcorder has no S-VIDEO output connector ... ... connect the camcorder’s AUDIO OUT and VIDEO OUT connectors to the recorder’s front panel AUDIO and VIDEO input connectors.
B
If the camcorder has an S-VIDEO output connector ... ... connect the camcorder’s AUDIO OUT and S-VIDEO OUT connectors to the recorder’s front panel AUDIO and S-VIDEO input connectors.
When using a monaural camcorder, connect its AUDIO OUT connector to the AUDIO L input connector on your recorder.
Set the recorder’s input mode.
B
Press
AUX (NUMBER
for the AUDIO and VIDEO input connectors, or “S-1” for the AUDIO and S-VIDEO input connectors, depending on the connectors being used.
Set the edit mode.
C
See “PICTURE CONTROL” on page 45.
key “0”) and/or PR to select “F-1”
Camcorder
Player
B
If the camcorder has an S-VIDEO output connector ...
S-VIDEO input
Audio cable (not provided)
S-Video cable (not provided)
Camcorder
AUDIO OUT
Your recorder
AUDIO input
S-VIDEO OUT
AUDIO OUT
Start the camcorder.
D
Engage the Play mode of the camcorder.
Start the recorder.
E
Engage the Record mode of the recorder.
NOTES:
All necessary cables can be obtained from your dealer.
When you select “EDIT” to dub tapes in step 3, be sure to
select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”) after you finish dubbing the tapes.
Player
Page 36
36
EN
Output/Input Set
EDITING (cont.)
L-1 OUTPUT and L-1 INPUT Setting
Set “L-1 OUTPUT” and “L-1 INPUT” to the appropriate mode depending on the type of appliance connected to the recorder’s AV1 (L-1) IN/OUT connector.
Access the Main Menu screen.
A
Press
B
Press rt to move the highlight bar (pointer) to “OUTPUT/INPUT SET”, then press OK or
C
Press highlight bar (pointer) to “L-1 OUTPUT” or “L-1 INPUT”. Then, press OK or the appropriate setting.
* The default setting is
the table below.
.
MENU
Access the Output/Input Set screen.
.
e
Select the output or input mode for the AV1 (L-1) IN/OUT connector.
to move the
rt
to select
e
in
bold
8
L-1 OUTPUT
: If a connected appliance’s input is
VIDEO
S-VIDEO:
8
L-1 INPUT
VIDEO
S-VIDEO
Return to the normal screen.
D
Press
MENU
compatible only with regular video signals, set to “VIDEO”. If a connected appliance’s input is compatible with Y/C signals, set to “S-VIDEO”. You can obtain high­quality S-VHS picture.
: If a connected appliance’s output is
compatible only with regular video signals, set to “VIDEO”.
: If a connected appliance’s output is
compatible with Y/C signals, set to “S-VIDEO”. You can obtain high­quality S-VHS picture.
.
NOTES:
If “L-1 OUTPUT” is set to “S-VIDEO”, it is impossible to set “L-1 INPUT” to “S-VIDEO”.
If “L-2 SELECT” is set to “DECODER”, it is impossible to set “L-1 INPUT” to “S-VIDEO”.
Page 37
EN
37
L-2 SELECT and L-2 INPUT Setting
Set “L-2 SELECT” to the appropriate mode depending on the type of appliance connected to the recorder’s AV2 (L-2) IN/ DECODER connector. Set “L-2 INPUT” to the appropriate mode depending on the output signals of the connected appliance.
Perform steps 1 and 2 of “L-1 OUTPUT and L-1 INPUT Setting” on page 36.
Select the input mode for the AV2 (L-2) IN/
A
DECODER connector.
Press rt to move the highlight bar (pointer) to “L-2
” or “L-2 INPUT”.
SELECT
Then, press OK or the appropriate setting.
* The default setting is
the table below.
8
L-2 SELECT
: To use this recorder as the recording
A/V
DECODER
: To view a satellite programme with
SAT
to select
e
in
bold
deck with the player connected to the AV2 (L-2) IN/DECODER connector, or to use the satellite receiver connected to the AV2 (L-2) IN/DECODER connector.
: To use a decoder connected to the
AV2 (L-2) IN/DECODER connector.
the TV set while the recorder is turned off. (
pg. 40)
NOTES:
If you have a satellite receiver or a decoder connected to the AV2 (L-2) IN/DECODER connector, be sure to set “L-2 SELECT” back to appropriate mode after editing.
If you are not connecting a satellite receiver or a decoder to the AV2 (L-2) IN/DECODER connector, leave “L-2 SELECT” set to “A/V”.
The default setting is “A/V”; if the recorder’s memory backup has expired due to a power cut or because the AC was removed from the recorder, “A/V” will be automatically selected when the power is restored to the recorder. If you are using a satellite receiver or a decoder, be sure to set “L-2 SELECT” back to appropriate mode.
When “L-2 SELECT” is set to “SAT”, “SAT” appears on TV screen or front display panel instead of “L-2” or “L2”.
If “L-2 SELECT” is set to “DECODER”, it is impossible to set “L-2 INPUT” to “S-VIDEO”.
If “L-1 OUTPUT” is set to “S-VIDEO”, it is impossible to set “L-2 SELECT” to “DECODER”.
8
L-2 INPUT
: If a connected appliance’s output is
VIDEO
S-VIDEO
Return to the normal screen.
B
Press
MENU
compatible only with regular video signals, set to “VIDEO”.
: If a connected appliance’s output is
compatible with Y/C signals, set to “S-VIDEO”. You can obtain high­quality S-VHS picture.
.
Page 38
38
EN
Edit To Or From Another Video Recorder
EDITING (cont.)
You can use your recorder as the source player or as the recording deck.
Make connections.
A
Connect the player’s 21-pin SCART connector to the recorder’s 21-pin SCART connector as illustrated on page
39.
A
When using your recorder as the source player ... ... connect its AV1 (L-1) IN/OUT connector to the recording deck.
B
When using your recorder as the recording deck ... ... connect its AV1 (L-1) IN/OUT or AV2 (L-2) IN/ DECODER connector to the source player.
C
If another recorder is compatible with the Y/C signal ... ... connect your recorder’s AV1 (L-1) IN/OUT connector to another recorder.
With C connection ...
When using your recorder as the recording deck, set “L-1 INPUT” to “S-VIDEO” and “L-2 SELECT” to “A/V” (
37).
When using your recorder as the source player, set “L-1 OUTPUT” to “S-VIDEO” (
Set the input mode of recording deck.
B
With this video recorder, press and/or PR to select “L-1” for the AV1 (L-1) IN/OUT connector, or “L-2” for the AV2 (L-2) IN/DECODER connector, depending on the connector being used.
When using another recorder as the recording deck, refer to its instruction manual.
When using the AV2 (L-2) IN/DECODER connector, set “L-2 SELECT” to “A/V” (
pg. 37).
pg. 36).
AUX (NUMBER
pg. 36,
key “0”)
Advantages of S-VHS video recorders
You can edit from VHS to S-VHS, S-VHS to VHS, or, from S-VHS to S-VHS.
From VHS to S-VHS: Record VHS playback signals in the S-VHS mode. Although the picture quality is inherently limited by that of the original, the edited tape has better picture quality than those made by VHS-to-VHS editing.
From S-VHS to VHS: Because the picture quality of the source material is very high, the edited tape has better picture quality than those made by VHS-to-VHS editing.
From S-VHS to S-VHS: All signals will be transferred with minimum degradation.
Set the edit mode.
C
See “PICTURE CONTROL” on page 45.
Start the source player.
D
Engage the Play mode of the source player.
Start the recording deck.
E
Engage the Record mode of the recording deck.
Page 39
EN
39
AB
TV receiver
Player
Your recorder
Recorder Your recorder
TV receiver
Video channel or AV mode
C
TV receiver
21-pin SCART cable
RF cable (provided)
S-Video cable (not provided)
21-pin SCART cable
(not provided)
Another recorder
Recorder
Player
(not provided)
Another recorder
Your recorder
21-pin SCART cable
(not provided)
Another recorder
Player
RF cable (provided)
Video channel or AV m ode
Recorder
NOTES:
All necessary cables can be obtained from your dealer.
For Y/C signal input/output, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.
When you select “EDIT” to dub tapes in step 3, be sure to select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”) after you
finish dubbing the tapes.
When you use this recorder as the source player for editing, be sure to set “O.S.D.” to “OFF” before starting (
If you are using another recorder with S-Video and Audio input/output connectors, you can connect those connectors to this
recorder’s S-VIDEO and AUDIO input/output connectors. When using your recorder as the source player ... ... connect its rear panel S OUT and AUDIO OUT connectors to the recording deck’s S-Video and Audio input connectors. When using your recorder as the recording deck ... ... connect its front panel S-VIDEO and AUDIO input connectors to the source player’s S-Video and Audio output connectors. Then, set the recorder’s input mode to “S-1”.
pg. 45).
Page 40
40
EN
SYSTEM CONNECTIONS
Connecting To A Satellite Receiver
Simple Connections
This is an example of simple connection if your TV has one 21-pin AV input (SCART) connector.
Connect the satellite receiver to the AV2 (L-2) IN/ DECODER connector, then connect the AV1 (L-1) IN/ OUT connector to the TV’s connector.
Outdoor unit
Satellite cable
Satellite receiver
Aerial
NOTES:
Set “L-2 SELECT” to “A/V” (
You can use Automatic Satellite Programme Recording
function (
To record a programme via the satellite receiver, select L-2 mode by pressing “L-2” appears on the front display panel.
For details, refer to the instruction manual of the satellite receiver.
TV aerial cable
ANT. IN
RF OUT
21-pin SCART connector
pg. 34) with this connection.
AUX (NUMBER
Aerial connector
pg. 37).
key “0”) and/or PR so that
Back of TV
Back of recorder
Mains outlet
IMPORTANT
When you set “L-2 SELECT” to “SAT” (墌pg. 37), it is possible to view a satellite broadcast with the TV set to its AV mode even if the recorder is turned off. When the recorder is in Stop mode or recording, press indicator on the front display panel.
If you turn on the recorder when the satellite receiver’s power is off, nothing appears on the TV screen. In this case, turn on the satellite receiver, or set the TV to its TV mode, or press mode.
button on the remote control to set the recorder to the video
TV/VCR
on the remote control to turn off the VCR
TV/VCR
Page 41
EN
41
Perfect Connections
This is an example of recommended connection if your TV has two 21-pin AV input (SCART) connectors.
Connect the decoder to the satellite receiver’s connector if you have a decoder, AV1 (L-1) IN/OUT connector to TV’s connector, and AV2 (L-2) IN/DECODER connector to the satellite receiver’s connector. Then connect the satellite receiver and TV.
Outdoor unit
Satellite cable
Satellite receiver
Aerial
NOTES:
Set “L-2 SELECT” to “A/V” (
You can use Automatic Satellite Programme Recording
function (
To record a programme via the satellite receiver, select L-2 mode by pressing “L-2” appears on the front display panel.
To receive a scrambled broadcast, descramble the signal with the satellite receiver.
For details, refer to the instruction manual of the satellite receiver and decoder.
TV aerial cable
pg. 34) with this connection.
AUX (NUMBER
21-pin SCART connector
ANT. IN
RF OUT
pg. 37).
key “0”) and/or PR so that
Aerial connector
Back of TV
Mains outlet
Decoder
Back of recorder
Page 42
42
EN
Connecting/Using
SYSTEM CONNECTIONS (cont.)
The AV2 (L-2) IN/DECODER connector can be used as an input connector for an external decoder (descrambler). Simply connect a decoder and you can enjoy the variety of programming that is available through scrambled channels.
A Decoder
TV receiver
(provided)
RF cable
TV aerial cable
AV1 (L-1) IN/OUTAV2 (L-2) IN/DECODER
Select the input mode.
A
Set “L-2 SELECT” to “DECODER”. (墌pg. 37)
Connect the decoder.
B
Connect your recorder’s AV2 (L-2) IN/DECODER connector to the decoder’s 21-pin SCART connector using a 21-pin SCART cable.
Set the tuner.
C
Perform the procedure as described in “When Receiving A Scrambled Broadcast” on page 51.
Decoder
Page 43
EN
43
Connecting/Using A Stereo System
These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo.
FM tuner
CD player
Stereo amplifier
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
AUX IN or TAPE MONITOR
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Speaker Television Speaker
Mains outlet
AUDIO OUT
Audio cable (not provided)
Back of recorder
Make connections.
Connect the AUDIO OUT L and R connectors on your video recorder to the AUX IN or TAPE MONITOR connectors on your stereo system’s receiver or amplifier.
NOTE:
When listening to sound through the connected stereo system, turn the TV’s volume down completely.
CAUTIONS:
This recorder has a dynamic range of more than 80 dB with regards to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them.
Some speakers and televisions are specially shielded to prevent television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the video playback picture.
Page 44
44
EN
Mode Set
SUBSIDIARY SETTINGS
You can change various mode settings on the Mode Set screen by following the procedure described below.
For each mode setting, see pages 45 to 47.
Turn on the TV and select the video channel (or AV mode).
Access the Main Menu screen.
A
Press
B
Press rt to move the highlight bar (pointer) to “MODE SET”, then press OK or
.
e
C
Press rt to move the highlight bar (pointer) to the item you want to change.
.
MENU
Access the Mode Set screen.
Select the mode.
Select the mode setting.
D
Press OK or e.
Return to the normal screen.
E
Press
MENU
.
Page 45
EN
45
8
B.E.S.T.
ON
OFF
8
PICTURE CONTROL
: Provides the optimised picture
AUTO
: Minimizes picture degradation
EDIT
: Reduces image coarseness when
SOFT
: Clearer, sharper-edged picture when
SHARP
8
AUTO TIMER
ON
OFF
benefits of the B.E.S.T. Picture System.
during editing (recording and playback).
viewing overplayed tapes containing a lot of noise.
viewing images with lots of flat, same-coloured surfaces such as cartoons.
* The default setting is
You can set the B.E.S.T. (Biconditional Equalised Signal Tracking) system to “ON” or “OFF” (
This feature helps you to adjust the playback picture quality according to your preference. Normally select “AUTO”.
in the table below.
bold
pg. 27).
NOTES:
When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will not change until you select another mode.
When you select “EDIT” to dub tapes, be sure to select “AUTO” after you finish dubbing the tapes.
When “B.E.S.T.” is “OFF”, “PICTURE CONTROL” switches automatically from “AUTO” to “NORM”.
When this function is set to “ON”, the timer is automatically engaged when the recorder power is turned off, and automatically disengaged when the recorder is powered back on.
NOTE:
For safety, when “AUTO TIMER” is set to “OFF”, all other recorder functions are disabled while the Timer mode is engaged. To disengage the timer, press
# (TIMER).
8
O.S.D.
ON
OFF
8
DIRECT REC
ON
OFF
When this function is set to “ON”, various operational indicators appear on the TV screen. Messages appear in the selected language (
pg. 13, 14).
NOTES:
When you use this recorder as the source player for editing, be sure to set “O.S.D.” to “OFF” before starting.
During playback, the operation mode indicators may be disturbed depending on the type of tape being used.
When this function is set to “ON”, you can easily start recording the programme that you are watching on your TV. Press and hold or press
on the recorder.
7
and press 4 on the remote control,
7
NOTES:
When you use the Direct Rec function, be sure to use a TV offering T-V LINK, etc. and connect a fully-wired 21-pin SCART cable between the recorder and the TV (
If “DIRECT REC” is set to “OFF”, the described in “Basic Recording” (
During the Direct Rec, “– –” appears on the front display panel.
pg. 8).
7 button functions as
pg. 23).
Page 46
46
EN
SUBSIDIARY SETTINGS (cont.)
8
AUTO SP]LP TIMER
ON
OFF
* The default setting is
in the table below.
bold
When this function is set to “ON”, the recorder automatically switches to LP mode to allow complete recording if there is not enough tape to record the entire programme while timer-recording in SP mode.
For Example . . .
Recording a programme of 210 minutes in length onto a 180-minute tape
Approximately 150 minutes Approximately 60 minutes
SP mode LP mode
Total 210 minutes
Make sure you set this function to “ON”, before the timer­recording starts.
NOTES:
If you have programmed the recorder to timer-record 2 or more programmes, the second programme and those thereafter may not fit on the tape if you set “AUTO SP this case, make sure the mode is not engaged, then set the tape speed manually during timer programming.
In order to ensure that the recording fits on the tape, this feature may leave a slight non-recorded section at the end of the tape.
There may be some noise and sound disturbance at the point on the tape where the recorder switches from SP to LP mode.
The Auto SP (Instant Timer Recording), and the feature will not work properly with any tapes longer than E-180, or with some tapes of shorter lengths.
If you perform timer recording with both VPS/PDC and the Auto SP
]LP Timer activated, and the programme goes beyond its
originally scheduled length, there may be times when the programme cannot be recorded in its entirety.
]LP Timer feature is not available during ITR
]LP TIMER” to “ON”. In
8
POWER SAVE
ON
OFF
When this function is set to “ON”, you can reduce the power consumption while the recorder is turned off.
NOTES:
During Power Save mode ... ... the front display panel will be turned off. ... the Just Clock function ( ... the picture may be distorted momentarily when you turn on/ off the recorder.
Power Save does not work when ... ... the recorder is in the Timer mode. ... the recorder’s power is turned off after timer-recording or Instant Timer Recording. ... the Automatic Satellite Programme Recording mode is engaged ( ... “L-2 SELECT” is set to “DECODER” or “SAT” (
pg. 34).
pg. 56) does not work.
pg. 37).
Page 47
EN
47
8
S-VHS
ON
OFF
8
COLOUR SYSTEM
PAL/NTS C
MESECAM
: To record PAL signals, or play back a
PAL or NTSC tape.
: To record SECAM signals, or play
back a MESECAM tape.
* The default setting is
Your recorder can record in S-VHS (Super VHS), S-VHS ET or VHS.
To record in S-VHS:
Set “S-VHS” to “ON”. Then, insert a cassette marked “S-VHS”. The S-VHS indicator lights up on the front display panel. The S-VHS recording mode is selected.
To record in S-VHS ET on a VHS cassette:
See “Super VHS ET (S-VHS ET)” on page 25.
To record in VHS:
Insert a cassette marked “VHS”. If the S-VHS ET button on the recorder is lit and S-VHS ET mode is activated, press off. The VHS recording mode is automatically selected regardless of the “S-VHS” mode setting.
To record in VHS on an S-VHS cassette:
Insert a cassette marked “S-VHS”. The S-VHS indicator lights up on the front display panel. Then, set “S-VHS” to “OFF”. The S-VHS indicator goes off. The VHS recording mode is selected.
You can play back PAL, NTSC and MESECAM tapes, or record PAL and SECAM* signals on this recorder. Select the appropriate colour system.
* SECAM signals will be recorded as MESECAM on this recorder;
MESECAM is the designation for tapes with SECAM signals that have been recorded on a MESECAM-compatible PAL video cassette recorder.
S-VHS ET
. The button’s light goes
in the table below.
bold
NOTES:
About NTSC Playback
Some TVs shrink the picture vertically and place black bars at the top and bottom of the TV screen. This is not a malfunction on the part of either the video recorder or the TV.
The picture may roll up and down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.)
The counter and tape remaining time readings will be incorrect.
During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour.
Depending on the type of TV, the top and bottom portions of superimposed displays may be cut off during NTSC playback.
Page 48
48
EN
Tuner Set
Turn on the TV and select the video channel (or AV mode).
SUBSIDIARY SETTINGS (cont.)
IMPORTANT
Perform the following steps only if — — Auto Channel Set has not been set correctly by Auto Set Up or by Preset Download ( — you have moved to a different area or if a new station starts broadcasting in your area.
Your recorder needs to memorize all necessary stations in channel positions in order to record TV programmes. Auto Channel Set automatically assigns all receivable stations in your area to call them up by using the PR buttons without going through any vacant channels.
pg. 10, 12).
Auto Channel Set
Turn on the recorder.
A
Press 1.
Access the Main Menu screen.
B
Press
C
Press rt to move the highlight bar (pointer) to “AUTO CH SET”, then press
or
OK
.
MENU
Access the Auto Channel Set screen.
.
e
Select your country.
D
Press rt to move the highlight bar (pointer) to your country’s name, then press OK or
Select the language.
E
Press rt to move the highlight bar (pointer) to the language of your choice.
.
e
Page 49
IMPORTANT
Beginning End
In certain reception conditions, station names may not be stored correctly, and Auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the S
HOWVIEW
programme of a different station. When programming the timer using the S desired channel is selected correctly ( “S
HOWVIEW
Your video recorder memorizes all detected stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture ( A Channel”).
system, the recorder will record a TV
HOWVIEW
®
Timer Programming”).
system, be sure to check the
pg. 28,
pg. 51, “Delete
EN
49
Perform Auto Channel Set.
F
Press OK twice.
If you have connected the recorder and your TV via AV connection ( recorder automatically performs the Preset Download and the T-V LINK screen will appear (
pg. 12).
The Auto Set screen appears, and remains on screen while the recorder searches for receivable stations. As Auto Channel Set progresses, the “ moves from left to right. Wait until the TV screen as shown in step 7 appears.
View the Confirmation screen.
G
After “SCAN COMPLETED” is displayed on the TV screen for about 5 seconds, the Confirmation screen looking like the one to the right appears. The stations your recorder located appear on a Confirmation screen — channel positions (PR), channels (CH) and station names (ID – blueback screen and the programme currently being broadcast by the blinking station appear alternately for 8 seconds each. To view the next page, use the button on the remote control.
The stations located in the selected country appear at the top of the list.
The Guide Program numbers will also be set automatically during Auto Channel Set.
Return to the normal screen.
H
Press
MENU
Using the Confirmation screen, you can skip or add channel positions, enter station names and perform other operations. Refer to pages 50 – 52 for the procedures.
Depending on reception conditions, the stations may not be stored in order, and the station names may not be stored correctly.
For information on scrambled broadcasts, refer to page 51.
pg. 8), the
.
q” mark on the TV screen
pg. 53). The
rt w e
NOTES:
Fine tuning is performed automatically during Auto Channel Set. If you want to perform tuning manually, refer to page 52.
If you perform Auto Channel Set when the aerial cable is not connected properly, “SCAN COMPLETED -NO SIGNAL-” appears on the TV screen in step 7. When this happens, make sure of the aerial connection and press OK; Auto Channel Set will take place again.
If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels (
pg. 51, “INFORMATION”).
Page 50
(E
12.
50
EN
Manual Channel Set
Store channels that were not stored during Auto Set Up (
pg. 10), Preset Download (墌pg. 12) or Auto Channel Set
(
pg. 48).
Access the Main Menu screen.
A
Press
B
Press rt to move the highlight bar (pointer) to “MANUAL CH SET”, then press OK or Confirmation screen appears.
C
Press rt w e until an open position in which you want to store a channel begins blinking, then press OK. The Manual Channel Set screen appears.
.
MENU
Access the Confirmation screen.
Select the channel position.
xample) To store in position
. The
e
SUBSIDIARY SETTINGS (cont.)
Select the band.
D
Press rt to change the band between CH (regular) and CC (cable), then press e.
Input the channel.
E
Press the want to store.
F
Press OK and the Confirmation screen appears.
G
Press
NUMBER
Input “0” before any single number entries. To input the registered station name (ID – until “– – – –” (ID setting) begins blinking, then press For fine tuning adjustment, press then press When storing a channel that sends scrambled broadcasts, press
e until “OFF” (Decoder setting) blinks, then press rt to
set “DECODER” to “ON” (“OFF” is the default setting). When “L-2 SELECT” is set to “A/V” or “SAT”, the “DECODER” setting cannot be changed (
Enter new channel information.
Repeat steps 3 – 6 as necessary.
Close the Confirmation screen.
MENU
To change positions, see “Change Station Channel Position” (
pg. 51).
If you wish to set station names other than the ones registered in your recorder, see “Set Stations (B)” (
keys to input the channel number you
pg. 53), press e
rt. While tuning, “+” or “–” appears.
.
e until “+/–” begins blinking,
pg. 37).
pg. 52).
rt.
ATTEN TION
Guide Program numbers are not set when channels are stored manually. If an attempt is made at timer programming with the S SET” screen appears; set the Guide Program numbers on this screen. ( Number Set”) Or perform “Guide Program Number Set” (
HOWVIEW
system in this state, the “GUIDE PROG
pg. 29, “ATTENTION — Guide Program
pg. 55).
The blueback screen and the programme currently being broadcast by the selected channel appear alternately for 8 seconds each.
Page 51
EN
51
Delete A Channel
Perform steps 1 and 2 of “Manual Channel Set” on page 50 to access the Confirmation screen before continuing.
Select the item.
A
Press rt w e until the item you want to delete begins blinking.
Delete a channel.
B
Press &.
The item directly beneath the cancelled one moves up one line.
Repeat steps 1 and 2 as necessary.
Close the Confirmation screen.
C
Press
MENU
.
Change Station Channel Position
Perform steps 1 and 2 of “Manual Channel Set” on page 50 to access the Confirmation screen before continuing.
Select the item.
A
Press rt w e until the item you want to move begins blinking. Then press OK and the station name (ID) and its channel (CH) number begin blinking.
When Receiving A Scrambled Broadcast
Select the decoder mode.
A
Set “L-2 SELECT” to “DECODER” (墌pg. 37).
Access the Confirmation screen.
B
Perform steps 1 and 2 of “Manual Channel Set” on page 50.
Select the position.
C
Press rt w e to select the channel position broadcasting scrambled programmes, then press OK twice
Change the decoder setting.
D
Press e until “OFF” (decoder setting) begins blinking, and set it to “ON” by pressing
Return to the Confirmation screen.
E
Press OK.
Repeat steps 3 – 5 as necessary.
Close the Confirmation screen.
F
Press
MENU
.
rt
.
.
Select the new position.
B
Press rt w e to move the station to the new channel position, then press OK.
Example: If you moved the station in position 4 to position 2, the
C
Press
stations originally in positions 2 and 3 each move down one space.
Repeat steps 1 and 2 as necessary.
Close the Confirmation screen.
.
MENU
INFORMATION
If you live in Eastern Europe, “TV SYSTEM” setting appears instead of “DECODER” setting on the Manual Channel Set screen. When you can see the picture but can hear no audio, select appropriate TV system (D/K or B/G). Normally, TV programmes are broadcasted as follows. For Eastern Europe : D/K For Western Europe : B/G
A Select a country in Eastern Europe in step 4 on page 48. B Press
C Press
e until the TV system (D/K or B/G) blinking on the
Manual Channel Set screen in step 4 on page 50.
rt to select appropriate TV System (D/K or B/G).
Page 52
52
EN
SUBSIDIARY SETTINGS (cont.)
Set Stations (A)
Set station names that are registered in your recorder.
Perform steps 1 and 2 of “Manual Channel Set” on page 50 to access the Confirmation screen before continuing.
Select the item.
A
Press rt w e until the item you want begins blinking.
Access the Manual Channel Set screen.
B
Press OK twice.
Select the new station.
C
Press e until the station name (ID) begins blinking, then press rt until the new station’s name (ID) you want to store begins blinking. Registered station names (
pg. 53) appear as you
press
D
Press OK.
E
Press
.
rt
Switch the stations.
The Confirmation screen appears. Repeat steps 1 – 4 as necessary.
Close the Confirmation screen.
.
MENU
Set Stations (B)
Set station names other than the ones registered in your recorder.
Perform steps 1 and 2 of “Manual Channel Set” on page 50 to access the Confirmation screen and then perform step 1 and 2 of “Set Stations (A)” above before continuing.
Select the character for station name.
A
Press e until the first letter of the station name begins blinking.
Enter the new character.
B
Press rt to cycle through the characters (A–Z, 0–9, –, f, +,
(space) ) and stop when the desired character is
I
indicated, then press characters the same way (maximum of 4). After entering all characters, press OK.
The Confirmation screen appears.
If you make a mistake, press begins blinking. Then enter the correct character by pressing
rt.
Close the Confirmation screen.
C
Press
MENU
.
to enter. Enter the remaining
e
w until the incorrect character
NOTE:
The characters available for the station name (ID) are A–Z, 0–9, –,
f, +, I (space) (maximum of 4).
Fine-Tuning Channels Already Stored
Perform steps 1 and 2 of “Manual Channel Set” on page 50 to access the Confirmation screen before continuing.
Select the channel to fine-tune.
A
Press rt w e until the channel you want to tune begins blinking.
Access the Manual Channel Set screen.
B
Press OK twice. The Manual Channel Set screen appears.
Perform tuning.
C
Press e until “+/–” begins blinking, then press rt until the picture is its clearest. Then press OK.
The Confirmation screen appears.
Repeat steps 1 – 3 as necessary.
Close the Confirmation screen.
D
Press
MENU
.
Page 53
TV Station And ID List
EN
53
ID* STATION NAME
1000 3SAT ADLT ANT3 ARD ARTE BBC BBC1 BBC2 BR3 C+ C1 CAN5 CANV CH4 CH5 CHLD CINE CLUB CMT CNN CSUR DISC DR DRS DSF ETB1 ETB2 EURO EUSP FEMM FILM FNET FR2 FR3 GALA HR3 INFO ITA1 ITA7 ITV JSTV KA2 KAB1 KAN2 LOCA M6 MBC MCM MDR MOVE MTV MTV3 N3 N-TV NBC NDR3 NED1 NED2 NED3 NEWS NICK NRK NRK2 ODE ORF1 ORF2
TV1000 3SAT ADULT ANTENA3 ARD ARTE BBC GROUP BBC1 BBC2 BAYERN3 CANAL PLUS PORTUGUSES CANALE5 KETNET CANVAS CHANNEL4 CHANNEL5 CHILD CINEMA TELECLUB CMT CNN ANDALUCIA DISCOVERY DR TV DRS DSF ETB1 ETB2 EURONEWS EUROSPORTS FEMMAN FILM FILMNET France2 France3 GALAVISION HESSEN3 INFO-KANAL ITALIA1 ITALIA7 ITV JSTV KA2 KABEL1 KANAL2 LOCAL M6 MBR MCM MDR MOVIE MTV MTV3 NORD3 N-TV NBC SUPER NDR3 NED1 NED2 NED3
NICKELODEON NRK NRK2 ODEON ORF1 ORF2
ID* STATION NAME
ORF3 OWL3 PREM PRO7 RAI1 RAI2 RAI3 RET4 21 RTBF RTL RTL2 RTL4 RTL5 RTP S4 SAT1 SBS SHOW SIC SKY SKYN SPRT SRTL STAR SVT1 SVT2 SWR TCC TELE TEL5 TF1 TM3 TMC TNT TRT TSI TSR TV1 TV2 TV3 TV4 TV5 TV6 TVE1 TVE2 TVG TVI TVN VCR VERO VH-1 VIVA VIV2 VMTV VOX VT4 VTM WDR1 WDR3 YLE1 YLE2 ZDF ZTV
* The “ID” abbreviation is what is shown on-screen in lieu of the station
name. The “ID” abbreviation is listed in the Confirmation screen and is displayed on the TV screen when the recorder is tuned to a different station.
ORF3 OWL3 PREMIERE PRO7 RAI1 RAI2 RAI3 RETE4 TELE21 RTBF1 or 2 RTL RTL2 RTL4 RTL5 RTP SCHWEIZ4 SAT1 SBS SHOW SOCIEDADE SKY CHANNEL SKY NEWS SPORT SUPER RTL STAR-TV SVT1 SVT2 SUEDWEST3 TCC TELE TELE5 TF1 TM3 TELEMONTECARLO TNT INT TRT INT TSI TSR BRTN TV1 TV2 TV3 TV4 TV5 TV6 TVE1 TVE2 TV GALICIA TV INDEPENDENT TV NORGE VIDEO VERONICA VH-1 VIVA VIVA2 VIDEO MUSIC VOX VT4 VTM West1 West3 YLE1 YLE2 ZDF ZTV
Page 54
54
EN
SUBSIDIARY SETTINGS (cont.)
Video Channel Set
Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the recorder through the RF cable.
IMPORTANT
Perform the following steps only if —
— interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area. — you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.
If you have connected the recorder to your TV via the AV or S-VIDEO connection (墌pg. 8, 9), since you do not need the video channel you have to set the video channel to off. If you have connected the recorder to your TV via the RF connection ( channel.
Before performing the following steps:
Make sure the recorder’s power is off and there is no cassette inserted in the recorder.
Then set your TV to UHF channel 50.
Access the Video Channel Set mode.
A
Hold down panel shows the following.
on the recorder until the front display
0
If the two vertical white bars appear clearly on the TV screen as shown to the right, go to step 4.
If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.
pg. 8), you have to set the correct video
Set the RF output system.
B
The blinking number on the display indicates the RF output system of your country.
If you have selected MAGYARORSZÁG (36), CESKÁ REPUBLIKA (42), POLSKA (48) or OTHER EASTERN EUROPE (EE) for the country setting ( “2”.
For other countries, set to “1”. Then press OK. (1: B/G 2: D/K)
Set the video channel.
C
With AV or S-VIDEO Connection
Press (or “2OUT– –”).
Now the video channel is set to off.
With RF Connection
Press channel between 22 and 69 which is not occupied by any local station in your area.
(Example) If channel 50 is available in your area
until the front display panel shows “1OUT– –”
PR –
or – to set the video recorder to a vacant
PR +
pg. 10, 14), press rt to set to
NOTES:
If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.
If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.
Exit the Video Channel Set mode.
D
Press OK on the remote control.
With AV or S-VIDEO Connection
To view picture signals from the video recorder, set your TV to its AV mode.
With RF Connection
The channel on which the TV screen in step 3 appears clearly is your video channel. To view picture signals from the video recorder, set your TV to the video channel.
Page 55
EN
®
S
HOWVIEW
Setup
IMPORTANT
Normally, Auto Set Up (墌pg. 10), Preset Download (墌pg. 12) or Auto Channel Set (墌pg. 48) sets the Guide Program numbers automatically. You need to set the Guide Program numbers manually only in the following cases.
When timer-programming with the S your recorder, is not selected,
OR
when you add a channel after Auto Set Up or Auto Channel Set has taken place, —Set the Guide Program number for that station manually.
When you wish to timer-record a satellite programme with the S —Set the Guide Program numbers for all satellite broadcasts received on your satellite receiver.
Turn on the TV and select the video channel (or AV mode).
HOWVIEW
system, the channel position, where the station you wish to record is received on
HOWVIEW
system,
55
Guide Program Number Set
Access the Main Menu screen.
A
Press
B
Press rt to move the highlight bar (pointer) to “INITIAL SET”, then press OK or
C
Press rt to move the highlight bar (pointer) to “GUIDE PROG SET”, then press OK or
D
Press rt to enter the Guide Program number for the desired station as shown in the TV listings. Then press OK or
.
MENU
Access the Initial Set screen.
.
e
Access the Guide Program Set screen.
.
e
Enter the Guide Program number.
.
e
(Example) When inputting the
Guide Program number 2 for ZDF.
Enter the receiving channel position number.
E
Press the select “TV PROG” or “SAT”. Then press number of the recorder’s channel position on which the Guide Program number’s broadcast is received by the recorder or the satellite receiver. Then press OK or
F
Press
NUMBER
rt
To timer-record a satellite programme with the S system, you need to install the provided Satellite Controller and perform the procedure described in “Satellite Receiver Control Setting” ( Repeat steps 4 and 5 as necessary.
Return to the normal screen.
MENU
key “0” to
to input the
pg. 15).
.
e
HOWVIEW
.
(Example) If ZDF is received on
channel position 2.
Guide Program Number
“Guide Program (GUIDE PROG) number” refers to the assigned TV station numbers, according to broadcast area, for the S
HOWVIEW
numbers can be found in most TV listings.
timer recording. The Guide Program
Page 56
56
EN
Clock Set
Turn on the TV and select the video channel (or AV mode).
SUBSIDIARY SETTINGS (cont.)
IMPORTANT
If you performed Auto Set Up (墌pg. 10), Preset Download (
pg. 12) or Auto Channel Set (墌pg. 48), without ever
having set the clock previously, the recorder’s built-in clock is also set automatically. Perform the following steps only if — —Auto Clock Set has not been performed correctly by Auto Set Up, Preset Download or Auto Channel Set.
OR
—the recorder’s memory backup has expired.
OR
—you want to change Just Clock setting ( the left column).
Turn on the recorder.
A
Press 1.
Access the Main Menu screen.
B
Press
C
Press rt to move the highlight bar (pointer) to “INITIAL SET”, then press OK or
.
MENU
Access the Initial Set screen.
.
e
“Just Clock” in
Just Clock
The Just Clock function provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. The Just Clock option can be set “ON” or “OFF” at the Clock Set screen (the default setting is “OFF”). Press OK until the Just Clock setting begins blinking, then press the setting.
IMPORTANT:
recorder’s built-in clock may be reduced, which could adversely effect timer recording. We recommend you to keep Just Clock on. In cases where the clock setting data from a PDC signal is incorrect, however, you are advised to keep Just Clock set to “OFF”.
If you turn off Just Clock, the accuracy of your
rt to change
Access the Clock Set screen.
D
Press rt to move the highlight bar (pointer) to “CLOCK SET”, then press OK or
. The Clock Set screen appears.
e
NOTE:
When you have selected MAGYARORSZÁG (36), CESKÁ REPUBLIKA (42), POLSKA (48) or OTHER EASTERN EUROPE (EE) for the country setting ( Clock function. Skip steps 6 and 7 on page 57.
pg. 10, 14), you cannot use Just
Page 57
EN
57
Set the date and time.
E
Press rt to set the time, then press OK or e. The “date” display begins blinking. Repeat the same procedure to set the date and year.
When you set the time, press and hold by 30 minutes.
When you set the date, press and hold by 15 days.
Set Just Clock.
F
The default setting is “OFF”. Set as desired by pressing
, then press OK or e.
rt
For the Just clock function,
If you set to “OFF”, you can disregard the next step as you won’t be able to receive regular clock adjustments.
Set the source channel position for clock
G
rt to change the time
rt to change the date
“Just Clock” on page 56.
data.
The recorder is preset to receive clock setting and adjustment data from channel position 1. Press rt to set the channel position to the number representing the station transmitting clock setting data, then press OK or e.
Start the clock operation.
H
Press
MENU
.
NOTES:
Just Clock (when set to “ON”) adjusts the recorder’s built-in clock every hour, except for 23:00, 0:00, 1:00 and 2:00.
Just Clock is not effective when ... ... the recorder’s power is on. ... the recorder is in the Timer mode. ... a difference of more than 3 minutes exists between the built­in clock’s time and the actual time. ... the recorder is in the Automatic Satellite Programme Recording mode ( ... the recorder is in the Power Save mode ( ... ”L-2 SELECT” is set to “SAT” (
If Just Clock is set to “ON”, the recorder’s clock is automatically adjusted at the start/end of Summer Time.
Just Clock may not function properly depending on the reception condition.
pg. 34).
pg. 37).
pg. 46).
Page 58
58
EN
TROUBLESHOOTING
Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair.
POWER
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. No power is supplied to the recorder.
2. The clock is functioning properly, but the recorder cannot be powered.
3. The remote control won’t function.
The mains power cord is disconnected. Connect the mains power cord.
#” is displayed on the front display
panel with “AUTO TIMER” set to “OFF”.
The batteries are discharged. Replace the dead batteries with new ones.
Press the # button to turn the “#” indicator off.
TAPE TR A N SPORT
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. The tape does not run during recording.
2. The tape will not rewind or fast­forward.
i
” is displayed on the front display
panel.
The tape is already fully rewound or fast-forwarded.
Press 4 to turn the “i” indicator off.
Check the cassette.
PLAYBACK
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. The playback picture does not appear while the tape is running.
2. Noise appears during visual search.
3. Noise appears during normal playback.
4. The playback picture is blurred or interrupted while TV broadcasts are clear or “USE CLEANING CASSETTE” message appears on the screen.
5. Breaks are noticeable in Hi-Fi soundtrack.
If you are using the RF connection, . . . the TV receiver’s channel selector is not set to the video channel. . . . the recorder’s video channel has not been correctly set.
If you are using the AV or S-VIDEO connection, the TV receiver is not set to the AV mode.
This is normal.
The automatic tracking mode is engaged.
The video heads may be dirty. Use a dry cleaning cassette TCL-2UX or
The automatic tracking mode is engaged.
If you are using the RF connection, . . . set the TV receiver to the video channel. . . . perform “Video Channel Set” (
pg. 54).
If you are using the AV or S-VIDEO connection, set the TV to its AV mode.
Try manual tracking. (
consult your JVC dealer.
Try manual tracking. (
pg. 21)
pg. 21)
Page 59
RECORDING
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. Recording cannot be started.
2. TV broadcasts cannot be recorded.
3. Tape-to-tape editing is not possible.
4. Camcorder recording is not possible.
TIMER RECORDING
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. Timer recording won’t work.
2. Timer programming is not possible.
3. “
#” and “[” on the front display
panel won’t stop blinking.
4. The cassette is automatically ejected, and “
#” and “[” on the front
display panel won’t stop blinking.
5. “
#” blinks for 10 seconds and the
Timer mode is disengaged.
6. The cassette is automatically ejected, the power shuts off and “ “
[” won’t stop blinking.
7. The S
HOWVIEW
record properly.
system does not timer-
#” and
EN
There is no cassette loaded, or the cassette loaded has had its record safety tab removed.
“L-1”, “L-2”, “F-1”, “S-1” or “SAT” has been selected as the input mode.
The source (another video recorder, camcorder) has not been properly connected.
All necessary power switches have not been turned on.
The input mode is not correct. Set the input mode to “L-1”, “L-2”, “F-1”
The camcorder has not been properly connected.
The input mode is not correct. Set the input mode to “L-1”, “L-2”, “F-1”
The clock and/or the timer have been set incorrectly.
The timer is not engaged. Press
Timer recording is in progress. Timer programming can’t be performed
The timer is engaged but there’s no cassette loaded.
The loaded cassette has had its record safety tab removed.
# has been pressed when there are no
programs in memory, or the timer record information has been programmed incorrectly.
The end of the tape was reached during timer recording.
The recorder’s channel positions have been set incorrectly.
Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed.
Set to the desired channel.
Confirm that the source is properly connected.
Confirm that all units’ power switches are turned on.
or “S-1”.
Confirm that the camcorder is properly connected.
or “S-1”.
Re-perform the clock and/or timer settings.
# and confirm that “#” is
displayed on the front display panel.
while a timer recording is in progress. Wait until it finishes.
Load a cassette with the record safety tab intact, or cover the hole using adhesive tape.
Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact.
Check the programmed data and re­program as necessary, then press
The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.
Refer to “Guide Program Number Set” (
pg. 55) and re-perform the procedure.
# again.
59
Page 60
60
EN
OTHER PROBLEMS
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. Whistling or howling is heard from the TV during camcorder recording.
2. When scanning channels, some of them are skipped over.
3. The channel cannot be changed.
4. Channel settings that were made manually seem to have changed or disappeared.
5. No channels are stored in the recorder’s memory.
TROUBLESHOOTING (cont.)
The camcorder’s microphone is too close to the TV.
The TV’s volume is too high. Turn the TV’s volume down.
Those channels have been designated to be skipped.
Recording is in progress. Press
After the manual settings were made, Auto Channel Set was performed.
The TV aerial cable was not connected to the recorder when Auto Set Up was performed.
The fully-wired 21-pin SCART cable was not connected between TV and the recorder when Preset Download was performed.
Position the camcorder so its microphone is away from the TV.
If you need the skipped channels, restore them (
channels, then press recording.
Perform manual setting again.
Turn off the recorder once and connect the TV aerial cable to the recorder properly, then turn on the recorder again. The recorder will try Auto Set Up again (
Turn off the recorder once and connect the fully-wired 21-pin SCART cable to the recorder properly, then turn on the recorder again. Then perform Preset Download again (
pg. 50).
9 to pause the recording, change
pg. 10).
4 to resume
pg. 12).
ATTE NTIO N
This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.
Page 61
QUESTIONS AND ANSWERS
EN
61
PLAYBACK
Q. What happens if the end of the tape is reached
during playback or search?
The tape is automatically rewound to the
A.
beginning.
Q. During search, slow, still and frame-by-frame
playback, I can’t hear any audio. What’s the problem?
This is normal.
A.
Q. Can the video recorder indefinitely remain in
the still mode?
No. It stops automatically after 5 minutes to
A.
protect the heads.
Q. When returning from variable-speed search to
normal playback, the picture is disturbed. Should I be concerned about this?
No, it is normal.
A.
Q. Noise bar appear during variable-speed search.
What’s the problem?
This is normal.
A.
Q. Sometimes, during Index Search, the video
recorder can’t find the programme I want to see. Why not?
There may be index codes too close together.
A.
TIMER RECORDING
Q. “o” and “#” remain lit on the front display
panel. Is there a problem?
No. This is a normal condition for a timer
A.
recording in progress.
Q. Can I programme the timer while I’m watching
a tape or a TV broadcast?
You won’t see the picture as it is replaced by the
A.
on-screen menu, but the audio from the programme or tape you’re viewing can be heard.
RECORDING
Q. When I pause and then resume a recording, the
end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen?
This is normal. It reduces distortion at the pause
A.
and resume points.
Q. Can the video recorder indefinitely remain in
the Record-Pause mode?
No. The video recorder goes to its Stop mode
A.
automatically after 5 minutes to protect the heads.
Q. What happens if the tape runs out during
recording?
The video recorder automatically rewinds it to
A.
the beginning.
Page 62
62
EN
SPECIFICATIONS
GENERAL
Power requirement : AC 220 V – 240 Vd, 50 Hz/60 Hz Power consumption
Power on : 23 W Power off : 5.2 W
Temperature
Operating : 5°C to 40°C
Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD)
: 400 mm x 94 mm x 344 mm Weight : 4.1 kg Format : S-VHS/VHS PAL standard Maximum recording time
(SP) : 240 min. with E-240 video cassette (LP) : 480 min. with E-240 video cassette
VIDEO/AUDIO
Signal system : PAL-type colour signal and CCIR
monochrome signal, 625 lines 50 fields
Recording system : DA4 (Double Azimuth) head helical
scan system Signal-to-noise ratio: 45 dB Horizontal resolution
: 250 lines (VHS)
400 lines (S-VHS) Frequency range : 70 Hz to 10,000 Hz (Normal audio)
20 Hz to 20,000 Hz (Hi-Fi audio) Input/Output : 21-pin SCART connectors:
IN/OUT x 1, IN/DECODER x 1
RCA connectors:
VIDEO IN x 1, AUDIO IN x 1,
AUDIO OUT x 1
S-Video connectors:
IN x 1, OUT x 1
TUNER/TIMER
TV channel storage capacity
: 99 positions (+AUX position) Tuning system : Frequency synthesized tuner Channel coverage : VHF 47 MHz – 89 MHz/
104 MHz – 300 MHz/ 302 MHz – 470 MHz
UHF 470 MHz – 862 MHz Aerial output : UHF channels 22 – 69 (Adjustable) Memory backup time
: Approx. 60 min.
ACCESSORIES
Provided accessories
: RF cable,
Satellite Controller RM-SD1,
Infrared remote control unit,
“R6” battery x 2,
S-VHS ET labels
Specifications shown are for SP mode unless otherwise specified. E.& O.E. Design and specifications subject to change without notice.
Page 63
LIST OF TERMS
EN
63
A
Auto Set Up........................................................ 10
AUTO SP
AUTO TIMER ..................................................... 45
Automatic Satellite Programme Recording.......... 34
LP TIMER ......................................... 46
]
B
B.E.S.T. Picture System ................................. 27, 45
C
Change Station Channel Position........................ 51
Check, cancel and change programmes............. 32
Clock Set............................................................ 56
COLOUR SYSTEM ............................................. 47
Connecting To A Satellite Receiver..................... 40
D
Delete A Channel............................................... 51
DIRECT REC................................................. 17, 45
E
EDITING ............................................................ 35
Elapsed Recording Time Indication .................... 25
Express Timer Programming ............................... 30
F
Fine-Tuning Channels Already Stored................. 52
G
Guide Program Number Set ......................... 29, 55
H
High-Speed (Turbo) Search................................. 20
I
Index Search ...................................................... 21
Instant ReView ................................................... 20
Instant Timer Recording (ITR) ............................. 24
J
Just Clock........................................................... 56
L
L-1 INPUT.......................................................... 36
L-1 OUTPUT...................................................... 36
L-2 INPUT.......................................................... 37
L-2 SELECT......................................................... 37
Language............................................................ 14
M
Manual Channel Set ........................................... 50
Manual Tracking ................................................ 21
Mode Set............................................................ 44
O
O.S.D. ................................................................ 45
ON-SCREEN DISPLAY..........................................6
Output/Input Set ................................................. 36
P
PICTURE CONTROL .......................................... 45
PLAYBACK ......................................................... 18
POWER SAVE..................................................... 46
Preset Download ................................................ 12
R
Record One Programme While Watching
Another .............................................................. 24
RECORDING...................................................... 23
Recording Resume Function ............................... 23
Repeat Playback ................................................. 22
S
Satellite Controller..............................................15
Satellite Receiver Control Setting ........................ 15
Set Stations (A).................................................... 52
Set Stations (B)....................................................52
S
HOWVIEW
S
HOWVIEW
Skip Search......................................................... 20
Slow Motion.......................................................19
Soundtrack Selection .......................................... 22
Still Picture/Frame-By-Frame Playback ............... 19
Super VHS ET (S-VHS ET) ............................. 25, 47
S-VHS................................................................. 38
®
Setup ..............................................55
®
Timer Programming ........................ 28
T
Tape position indicator .........................................6
Tape Remaining Time......................................... 25
TIMER RECORDING ..........................................28
Timer warning display .......................................... 6
Tuner Set ............................................................ 48
T-V LINK ............................................................ 17
TV Station And ID List ........................................ 53
V
Variable Speed Search........................................19
Video Channel Set..............................................54
VPS/PDC Recording ...........................................31
W
When programmes overlap each other...............33
When Receiving A Scrambled Broadcast ............51
N
Next Function Memory ...................................... 21
Page 64
Auto Set Up — referring to the front display panel
The Auto Set Up function sets the tuner channels, clock and Guide Program numbers automatically.
BEFORE YOU START PLEASE MAKE SURE THAT:
The TV aerial cable is connected to the ANT.IN connector on the rear panel of the video recorder.
8
The video recorder’s mains power cord is connected to a mains outlet.
8
The video recorder is turned off.
8
Load batteries into the remote control.
8
Press 1 (recorder/remote).
1
Press rt (remote) to select the international telephone
2
country code. (Example) DEUTSCHLAND is selected.
International Telephone Country Code
BELGIUM
ESKÁ REPUBLIKA
C
DAN MARK DEUTSCHLAND ESPAÑA GREECE ITALIA MAGYARORSZÁG NEDERLAND NORGE
:
32 : : : : : : : : :
ÖSTERREICH
42
POLSKA
45
PORTUGAL
49
SUISSE
34
SUOMI
30
SVERIGE
39
РОССИЯ
OTHER WESTERN EUROPE
36
OTHER EASTERN EUROPE
31
47
EN
:
43
:
48
:
351
:
41
:
358
:
46
:
07
:
– –
:
EE
If you have selected a country code other than 32 (BELGIUM) or 41 (SUISSE), go to step
If you have selected 36 (MAGYARORSZÁG), 42 (CESKÁ REPUBLIKA), 48 (POLSKA) or EE (OTHER EASTERN
EUROPE), press OK. Clock Set screen will appear. Set the clock manually
If you have selected 32 (BELGIUM) or 41 (SUISSE), press OK (remote) and select the language code by pressing
(remote), then go to step 3.
rt
(墌pg. 56), then go to step 3.
.
3
(Example) FRANCAIS is selected for BELGIUM.
Language Code
ENGLISH DEUTSCH FRANCAIS
International Telephone
Language Code
Country Code
Press OK (remote). “Auto” appears on the front display panel.
3
Press OK (remote) to start Auto Set Up. Do NOT press any button on the video recorder or remote control during
4
ITALIANO CASTELLANO NEDERLANDS SVENSKA
:
01 : : : : : :
NORSK
02
SUOMI
03
DAN SK
04
POLSKI 05 06 07
TINA
CEc
MAGYAR
ЯЗЫК
: : : : : : :
“Auto” is blinking.
If you have connected the recorder to your TV via the AV connection (
perform Preset Download ( If “– –:– –” appears on the display panel, see page 13 of the instructions.
pg. 12).
pg. 8), the recorder will automatically
* Once you have performed Auto Set Up, even if the recorder’s memory backup has expired, the recorder will not
perform Auto Set Up again. Perform tuner setting (
pg. 48) and/or clock setting (墌pg. 56) as required.
08 09 10 11 12 13 14
FOR MORE INFORMATION SEE INSTRUCTIONS (
pg. 10)
Printed in Japan
Printed in Japan
Printed in JapanPrinted in Japan 0300IYV
0300IYV
0300IYV0300IYV
ID
ID*VP
IDID
*
VP
VPVP
Loading...