JVC HR-P94K, HR-P54A User Manual

INSTRUCTIONS

PAL NTSC

Hi-Fi KARAOKE MULTI 6HEAD

TAPE POSITION ON SCREEN AUTO VOLTAGE B.E.S.T. PICTURE

PAL/MESECAM/NTSC3.58/4.43 NTSC PLAYBACK ON PAL TV

MULTI SYSTEM

SUPER HEAD CLEANER

Hi-Fi

Karaoke

STANDBY/ON

MIC 21

POWER-ON STANDBY/REC

OSD SP/LP/EP

VIDEO CASSETTE PLAYER

HR-P94K

PAL NTSC

Hi-Fi KARAOKE MULTI 6HEAD

LONGPLAY RECORDING AUTO VOLTAGE B.E.S.T. PICTURE

PAL/MESECAM/NTSC3.58/4.43 NTSC PLAYBACK ON PAL TV

MULTI SYSTEM

SUPER HEAD CLEANER

STANDBY/ON

POWER-ON STANDBY/REC

OSD SP/LP/EP

VIDEO CASSETTE PLAYER

HR-P54A

OUTIN

RF OUT

ANT.IN

AUDIO

VIDEO

OUTIN

RF OUT

ANT.IN

AUDIO

VIDEO

English

VIDEO CASSETTE PLAYER

HR-P94K/P54A

Thank you for purchasing this JVC video cassette player. To ensure optimum performance of this unit, please read this instruction manual thoroughly.

Features

• 3 system (PAL/MESECAM/NTSC)

• NTSC playback (on PAL television)

• RF output G/K switchable

• Digital auto tracking

• HQ (High Quality)

• Auto playback function

• Repeat playback

• Shuttle search

• Still and slow motion

• Line recording

• Karaoke (HR-P94K only)

• B.E.S.T. (Biconditional Equalized Signal

Tracking) picture system

PAL NTSC

7 Only cassettes marked “VHS” can be used with this video cassette player.

Automatic features

Auto power on

The video cassette player is automatically turned on when the tape is inserted.

Auto rewind

The video tape is automatically rewound when the end of the tape is reached during the play, recording or shuttle search forward mode.

Auto playback

If the video cassette’s safety tab has been removed, playback will begin automatically when the tape is inserted into the video cassette player.

Power off eject

Even when the video cassette player’s power is off, pressing the eject button will turn the power on and eject the tape. Once ejected, the power will be turned off again automatically.

Auto head cleaning

When a tape is loaded or ejected the VCP video head is cleaned automatically.

LPT0457-001A

Precautions

The rating plate and the safety caution are on the rear of the unit.

WARNING: DANGEROUS VOLTAGE IN-SIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO

RAIN OR MOISTURE.

The STANDBY/ON button does not completely shut off mains power from the unit, but switches operating current on and off.

This unit is produced to comply with Standard IEC 60065.

When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both side, on top and at the rear.)

When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly.

Failure to heed the following precautions may result in damage to the player, remote control or video cassette player.

1. DO NOT place the player . . .

... in an environment prone to extreme temperatures or humidity. ... in direct sunlight. ... in a dusty environment. ... in an environment where strong magnetic fields are generated. ... on a surface that is unstable or subject to vibration.

2. DO NOT block the player's ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

3. DO NOT place heavy objects on the player or remote control.

4. DO NOT place anything which might spill on top of the player or remote control.

If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

5. DO NOT expose the apparatus to dripping or splashing.

6. DO NOT use this equipment in a bathroom or places with water. Also DO NOT place

any containers filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this unit.

7. DO NOT place any naked flame sources, such as lighted candles, on the apparatus.

8. AVOID violent shocks to the player during transport.

Beware of moisture condensation

Moisture in the air will condense on the VCP when you move it from a cold place to a warm place, or under extremely humid conditions — just as water droplets form on the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the VCP’s power turned on for a few hours to let the moisture dry.

When transporting

7 Be sure to remove cassette from VCP before packing. 7 Avoid violent shocks to the VCP during packing and transport.

Controls

Front panel

HR-P94K

HR-P54A

Rear panel

HR-P94K

HR-P54A

Front panel

STANDBY/ON button

To turn the power on and off (standby mode).

Cassette loading slot

Load the video cassette here.

Rewind

1 button

To rewind the video tape and to start reverse shuttle search playback mode.

Play

# button

To start playback.

Fast forward

¡¡

¡ button

¡¡

To fast forward the video tape and to start forward shuttle search playback mode.

SP / LP / EP button

To select the recording tape speed.

Stop/Eject

§§

§ button

§§

To stop playback and to eject the video tape.

Record

¶¶

¶ button

¶¶

To start recording.

OSD button

To display the information on the television's display.

Remote sensor window

For remote control operation.

STANDBY / REC indicator

• Lights when the power turns off (Standby mode) or during recording mode.

• Blinks during recording pause mode.

POWER-ON indicator

Lights when the power turns on.

MIC input terminals (HR-P94K only)

Rear panel

AC power cord

RF. OUT terminal

AUDIO/VIDEO IN terminals

AUDIO/VIDEO OUT terminals

ANT. IN terminal

∗ The video cassette player illustrations appearing in this instruction manual are of the HR-P94K.

Wireless remote control

When using the remote control for operation of the video cassette player, make sure that it is pointed at the remote sensor window. You can also use the player’s remote control to operate a JVC television.

STANDBY/ON button

To turn the power on and off (standby

TRACKING –/+ buttons

TV/VCR

– TRACKING +

AUTO

0000/X

PLAY

FFREW

To adjust tracking during playback.

0000 / button

To reset the tape counter.

¡¡

Z button

To fast forward the video tape. Also to start forward shuttle search playback.

STOP

TV PR TV

– +

–

REC

LP00000-000

Transmitting window

11 22

TV/VCR (Player) button

To switch JVC TV’s mode between TV and VIDEO.

TV button

To enable remote control of JVC TV.

AUTO button

To enable/disable auto tracking mode.

SP/LP/EP( ) button

• To select the recording tape speed.

• To select JVC TV’s sounds.

(TV Muting) button

• To select output sound mode (HRP94K only).

• To mute the JVC TV volume.

3 PLAY button

To start playback.

REW

+ button

To rewind the video tape. Also to start reverse shuttle search playback.

7 STOP button

To stop playback.

MENU button

To accesse Mode Set screen.

▲/▼ buttons

To select the mode.

TV PR +/– buttons

To select a prest position.

PAUSE

OK/OSD

VCP/TV

8 PAUSE button

To freeze the picture during playback. Also to engage the recording pause mode.

2/3 buttons

To set the mode.

TV +/– (TV Volume) buttons

To adjust the TV volume.

OK/OSD button

• To fix the setting.

• To display the information on the

television's display.

¶¶

¶ REC button

¶¶

Press the

¶¶

¶ REC and

¶¶

tons together, to start recording.

Operating JVC TVs

Buttons with a small dot on the left side of the name can also be used to operate your JVC TV while holding down TV. To operate your TV, while holding down TV, press the corresponding button: , TV/

VCR, TV PR +/–, TV +/– (TV Volume),

(TV Muting), (TV Sounds).

Notes:

• Point the remote control toward the remote sensor window.

• The maximum operating distance of the remote control is about 8 m.

• When inserting the batteries, be sure to insert in the correct directions as indicated under the battery cover.

• If the remote control doesn’t work properly, remove its batteries, wait a short time, replace the batteries and then try again.

3 PLAY but-

On screen display

When “O.S.D” is set to “ON” ( See “9 Mode set”), various operational indicators appear on the TV screen.

Operation mode indicators

11 22

Tape speed SP/LP/EP

22 33

Colour system indicator

33 44

Tape direction

44 55

Counter display

55 66

Audio mode display (HR-P94K only)

66 77

Tape position indicator

77 88

Cassette loaded mark

77 66

Connections

HIFI –9 : 59 : 59

]SP

NTSC 3.58

22 33

Make sure that the power to the video cassette player and TV is off before making the following connections.

Connection A

RF OUT

OUTIN

AUDIO

ANT.IN

VIDEO

Connection B

Note:

If you put a TV set directly on this Video cassette player or install it too close to a TV set, noise may occur. If this noise occurs, separate the Video cassette player and the TV set.

Connection A (basic)

In order to use the video cassette player it must be connected between the antenna and the TV.

Connect your TV antenna cable to the video cassette player’s ANT. IN terminal.

Connect one end of the provided RF antenna cable to the video cassette player’s

RF. OUT terminal and the other end to the TV’s antenna terminal.

Connect the power cord to your household AC outlet.

Connection B

For connection of a TV that has VIDEO/AUDIO IN/OUT terminals. This connection is necessary to record TV programmes. Use RCA type pin connection cords (available from audio/video stores) for connection. This connection is in addition to connection A.

Follow steps 1 and 2 of “Connection A”.

Connect the TV’s VIDEO OUT and AUDIO OUT terminals to the video cassette

player’s VIDEO IN and AUDIO IN terminals.

Connect the TV’s VIDEO IN and AUDIO IN terminals to the VCP’s VIDEO OUT and

AUDIO OUT terminals.

Connect the power cord to your household AC outlet.

Setting the video channel

To watch videos on your TV, it must be set to the same UHF channel as the video cassette player. This channel is used as the video channel. This video cassette player has been preset to UHF channel 36.

Note:

• When you have connected the VIDEO/AUDIO OUT terminals of this video cassette player to your TV’s video/audio in terminals (connection B of the “Connections” section), setting the video channel is not necessary. In this case simply set the TV’s TV/VCR switch to VCR.

IMPORTANT:

Before performing the following steps, make sure the player's power is off and there is no cassette inserted in the player.

Access video channel set mode.

POWER-ON STANDBY/REC

Hold down player until the both of POWER-ON and STANDBY/REC indicators light.

Set video channels.

Set your TV to UHF channel 36.

• If the two vertical white bars appear clearly on the screen as shown in the illustration on the right, press OK and then go to step 3.

• If the two vertical white bars do not appear clearly, press TRACKING + or – to set the video cassette player to a vacant channel between 32 and 40 which is not occupied by any local station in your area.

• The mode indicators tell channel position. The indicators blink different speed by the channel position as shown on the right.

Press OK.

• STANDBY/REC indicator goes off.

Set TV system.

Set “RF OUT” to “B/G” or “D/K”. ( See “9 Mode set”)

§§

§ on the video cassette

§§

POWER ON indicator

STANDBY/REC indicator

TEST SIGNAL

The channel on which the screen to the left appear clearly in step 2 is your Video Channel.

To view picture signals from the video player, set your TV to the Video Channel.

CH POWER-ON STANDBY/REC Blinking

(green) (red) Speed

40 – blink fast 39 – blink 38 – blink 37 – blink slow 36 light light – 35 blink – slow 34 blink – 33 blink – 32 blink – fast

Mode set

You can change various mode setting on the Mode Set screen by following procedure described below.

Access the Mode Set screen.

Press MENU.

Select the mode.

Press ▲/▼ to move the pointer to the item you want to change.

Select the mode setting.

Press 2/3.

Return to the normal screen.

Press MENU.

7MIC (HR-P94K only)

7ECHO (HR-P94K only)

7O.S.D

OFF

7B.E.S.T.

OFF

7NTSC

NTSC3.58:

Select this mode to watch NTSC tapes on a NTSC system TV.

NTSC4.43:

Select this mode to watch NTSC tapes on a multi-system TV. (that has an NTSC4.43 setting) Select NTSC4.43 to record 4.43 signal.

NTSC→PAL:

Select this mode to watch NTSC tapes on a PAL system TV.

7RFOUT B/G: New Zealand, Kuwait,

U.A.E., Indonesia, Singapore, Thailand, Malaysia, Iran, Saudi Arabia

D/K: Egypt, Morocco, Lebanon,

Iraq, China, Mongolia, Russia

See “Karaoke features” below.

When the function is set to “ON”, various operational indicators appear on the TV screen.

NOTE:

When you use this video cassette player as the source player for editing, be sure to set “O.S.D” to “OFF” before starting.

You can set the B.E.S.T.(Bicondional Equalized Signal Tracking) system to “ON” or “OFF”.

To watch an NTSC tape, it will be necessary to select one of the output mode.

NOTES:

NTSC Playback on PAL TV

• The vertical size of the playback picture will shrink and some picture “noise” may appear on the screen.

• The playback picture may roll. In this case adjust the picture with the TV’s vertical hold knob (with some TV’s this adjustment may not be possible).

• The colour of the playback picture may differ from the original.

• In the forward/reverse shuttle search or still modes there may be no colour depending on the TV and video cassette player combination.

Set appropriate TV system that matches the system of TV being used.

∗The default setting is bold in the table below.

MIC MIN+---+-7-+MAX ECHO 0+---+-

O.S.D. ON B.E.S.T. ON NTSC NTSC 3.58 RF OUT B/G

[

▲/▼] = [

[MENU] : EXIT

∗“MIC” and “ECHO”appears

only with the HR-P94K.

2/3

-+10

]

Playback

NTSC, PAL and MESECAM video tapes can be played back on this video cassette player. Refer to the “Mode Set” section for details.

Before proceeding:

• Turn on the power of the TV and video cassette player.

• Make sure that the TV is set to the video channel or that the TV’s TV/VIDEO switch is set to VIDEO (refer to the “Setting the video channel” section for details).

Hi-Fi KARAOKE MULTI 6HEAD

TAPE POSITION ON SCREEN AUTO VOLTAGE B.E.S.T. PICTURE

MULTI SYSTEM

PAL/MESECAM/NTSC3.58/4.43 NTSC PLAYBACK ON PAL TV

SUPER

POWER-ON STANDBY/REC

HEAD CLEANER

AUTO

TV PR TV

–

Load a pre-recorded cassette.

If the safety tab on the cassette is removed, playback will start automatically.

Press

- to start playback.

7 Press § or the remote control’s 7

To fast forward or rewind the tape: 7 From the stop mode, press ¡ or

• “B.E.S.T. PICTURE SYSTEM” appears on the screen. (when B.E.S.T. is set to “ON”. “9 Mode set”)

to stop playback. Then press § to remove the cassette.

TV/VCR

STOP

REC

– TRACKING +

PLAY

– +

VIDEO CASSETTE PLAYER

0000/X

FFREW

PAUSE

OK/OSD

PAL NTSC

HR-P94K

OSD SP/LP/EP

Slow motion playback

Slow motion playback is 1/6 of the normal playback speed. The sound will be cut during slow motion playback.

During playback:

Press

8 for 2 seconds.

7 Press 3 to return to the normal play-

back speed.

Notes:

• If the picture shakes during the slow mode, use TRACKING +/– to correct the picture.

• After approx. 5 minutes, the slow mode will disengage to protect the video tape.

Still picture and frame advance

Use this feature to freeze the playback picture and to advance one frame at a time. The sound will be cut during this mode.

During playback:

Press

1 2

7 Press 3 to resume normal playback.

Notes:

• If the picture shakes during the still

• After the picture has been frozen for

The picture will be frozen.

Press

8 repeatedly to advance

frames.

Each time the button is pressed the still picture will advance one frame.

mode, use TRACKING +/– to correct the picture.

approx. 5 minutes, the still mode will disengage to protect the video tape.

Shuttle search playback

Use this feature during playback to visually locate any point on a recorded cassette. The sound will be cut during shuttle search operation.

During playback:

¡¡

Press

search forward or reverse.

7 Press 3 to resume normal playback.

Note:

For short searches, press and hold

1. When released, normal playback will

continue.

¡ or

1 to engage shuttle

¡¡

¡ or

¡¡

Tracking adjustment

Automatic tracking is adjusted each time a cassette is inserted in the video cassette player, you may wish to adjust tracking manually during playback.

Manual tracking:

Press the remote control’s AUTO.

Press the remote control’s TRACK-

ING + or – to adjust tracking.

7 Press AUTO to return to automatic

tracking.

Counter reset

Press OSD to show counter display

on the screen.

Press 0000 to reset the counter.

Repeat playback

Use this feature to repeat playback of a cassette 100 times.

During playback:

Press

3 for more than 5 seconds.

Note:

Pressing 3, playback.

The Play indicator will blink slowly and playback of the cassette will repeat 100 times automatically.

Press

7 to stop repeat playback.

Tape playback will be stopped and the repeat playback mode will be cancelled.

¡¡

¡ or

8 also stops Repeat

¡¡

Rewind playback or power off

When the tape has finished rewinding, the Video cassette player will play back or turn itself off.

During stop:

a- For Automatic Start Of Playback

b- For Automatic Power Off

Press

1, then press

onds.

Press

1, then press within 2

seconds.

ATTENTION:

In the search, still, slow-motion or frame advance mode,

• the picture will be distorted.

• the noise bars will appear.

• there will be loss of colour.

• the picture may not appear.

However, this is not malfunction. These problems may occur especially with HR-P54A.

3 within 2 sec-

Recording

Use the following procedure to record TV programmes on a blank video tape.

Before proceeding:

• To record TV programmes, the video cassette player must be connected to the TV as shown in connection B of the “Connections” section.

• Turn on the power of the TV and video cassette player.

• Make sure that the video cassette’s safety tab is intact. If it has been removed, cover the

hole with adhesive tape.

Load a blank video tape.

Hi-Fi KARAOKE MULTI 6HEAD

TAPE POSITION ON SCREEN AUTO VOLTAGE B.E.S.T. PICTURE

MULTI SYSTEM

PAL/MESECAM/NTSC3.58/4.43

PER

EAD CLEANER

NTSC PLAYBACK ON PAL TV

POWER-ON STANDBY/REC

VIDEO CASSETTE PLAYER

PAL NTSC

HR-P94K

OSD SP/LP/EP

TV/VCR

– TRACKING +

AUTO

0000/X

PLAY

FFREW

PAUSE

STOP

TV PR TV

– +

–

REC

OK/OSD

VCP/TV

LP00000-000

Notes:

• To engage recording standby, press ¶ and then press 8. The STANDBY/REC indicator will blink during recording standby. Press 3 again to start recording.

• If ¶ does not work, check to see if the cassette safety tab has been removed.

• The player automatically stops when record-standby continues for more than 5 minutes.

• The video tape will be rewound automatically when the end of the tape is reached.

Press SP/LP/EP( ) to set the recording speed.

Press ¶ to start recording. (On the

remote control unit press ¶ and 3 at the same time.)

The recording indicator will light during recording.

B.E.S.T. takes place at the beginning of each first SP and first LP (or EP) recording after inserting the cassette.

7 Press § or the remote control’s 7

to stop recording.

To stop recording temporarily: 7 Press 8.

The recording indicator will blink. Press 3 to resume recording.

Karaoke features

Karaoke (HR-P94K only)

Use this feature to enjoy karaoke video. Connect a microphone to both MIC 1 and MIC 2 for duets.

Insert a pre-recorded Karaoke tape.

Press

7 Karaoke search

You can search the desired tune by pressing 2/3. The Karaoke search can be operated only when the mute section is more than 4 seconds between tune and tune.

Adjust the MIC or ECHO volume as

necessary.

Press MENU to access the Mode Set screen then press ▲/▼ to select MIC or ECHO. Press 2/3 to adjust the MIC or ECHO volume. Press MENU to return normal screen.

Start singing.

Note:

Check that the power is off (standby mode) before plugging in the microphone.

7 Soundtrack Selection (HR-P94K only)

During Playback Pressing changes the soundtrack being played back as follows:

HI-FI HI-FI L HI-FI R

HI-FI NORM

NORM

B.E.S.T. picture system

The B.E.S.T. (Biconditional Equalized Signal Tracking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. The default setting for both recording and playback is ‘‘ON’’.

Recording

The video cassette player assesses the quality of the tape once you initiate recording.

7 The player spends approximately 7 sec-

onds assessing the condition of the tape, then begins recording.

Notes:

• The B.E.S.T. system works only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.

• Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re-performed.

ATTENTION:

Since the B.E.S.T. system works before recording actually starts, there is a delay of approximately 7 seconds after ¶ and 3 on the remote are pressed, or ¶ on the player is pressed. To make sure you record the desired scene or programme in its entirely, first perform the following steps: 1 Press and hold

the Record Pause mode.

• The player then automatically check the condition of the tape and, after approximately 7 seconds, reenters Record Pause.

2 Press 3 to start recording.

• If you want to bypass the B.E.S.T. system and begin recording immediately, set “B.E.S.T.” to “OFF”.

8 and

¶¶

¶ to engage

¶¶

Playback

The video cassette player assesses the quality of the tape once you initiate playback. When watching a tape recorded with B.E.S.T. set to on, it is recommended that you leave B.E.S.T. on during playback as well.

7 The player adjusts the playback picture

quality based on the quality of the tape in use.

7 B.E.S.T. is active during Auto Tracking.

Note:

When watching a rental tape, or one recorded on another video player, set B.E.S.T. to on or off to your preference.

Editing

Editing To/From Another Recorder

Player

RF OUT

OUTIN

AUDIO

ANT.IN

VIDEO

Recorder

Connect the player’s AUDIO and

VIDEO OUT connectors to the recorder’s AUDIO and VIDEO IN connectors.

Put the player in the Play mode.

Audio/Video signals

Receiver

RF OUT

AUDIO

ANT.IN

VIDEO

VIDEO CHANNEL

OUTIN

Put the recorder in the Record mode.

Notes:

• NTSC tapes being played back in the NTSC PLAYBACK ON PAL TV mode cannot be dubbed to another recorder.

• When you dub an NTSC tape using your recorder as the playback deck, select NTSC 3.58 (or 4.43) with the Colour System Output switch.

Important:

7 To edit, both the player and the

recorder must be of the same colour system. Set “NTSC” to appropriate mode. ( See “9 Mode set”)

Troubleshooting

Problem

No power

Tape cannot be ejected

No picture

No colour

Shuttle search does not function

Disturbances in playback picture

Remote control does not function

Auto playback does not function

Recording does not function

The video cassette player does not function properly

Is the power cord plugged in? Is the power turned on?

Was the video cassette player’s § button pressed?

Is the TV set to the video channel? Is a cassette loaded? Are the connections correct?

Set the Colour System Output switch according to the recorded tape system.

Is the video cassette player in the playback mode?

Is tracking adjusted properly? Is the TV adjusted properly? Install this VCP a little way apart from the TV set.

The batteries are weak. Replace the batteries.

The video cassette’s recording safety tab has not been removed.

Are the connections correct? Was the Record button pressed? The video cassette’s recording safety tab is removed.

Microcomputer malfunction. Disconnect the power plug from the AC outlet and then re-insert it. The microcomputer will be reset to its initial mode.

Check point

About Head cleaning

7 If the picture playback becomes blurred, it does not mean that the recorded program has

been erased.

7 Dirt accumulated on the video heads after long periods of use causes such troubles. In

this case, head cleaning requiring highly technical care is necessary.

7 For head cleaning, consult the nearest JVC dealer.

Specifications

Format ...................................... VHS Standard

Video recording system ........... Rotary, slant azimuth helical scan system

Rotary heads ............................ [HR-P94K]

RF output ................................. System B/G, D/K type modulation

Recording (line input) ............... PAL, SECAM (MESECAM tape)

Playback (line output) .............. PAL, SECAM (MESECAM tape)

Video

Line input level ....................... 0.5 – 2.0 Vp-p/75 ohms, unbalanced

Line output level .................... 1.0 Vp-p/75 ohms, unbalanced

S/N ratio ................................. More than 45 dB

Horizontal resolution .............. More than 250 lines

Audio

Line input level ....................... –8 dBs/50 k ohms, unbalanced

Line output level .................... –8 dBs/1 k ohm, unbalanced

Frequency response .............. 70 Hz to 10,000 Hz (Normal)

Power requirements

Rating .................................... AC 110 V – 240 V, 50 Hz / 60 Hz

Operating ............................... AC 90 V – 260 V, 50 Hz / 60 Hz

Power consumption ................. [HR-P94K]

Operation temperature ............. 5°C to 40°C

Dimensions .............................. 360 mm (W) × 94 mm (H) × 279 mm (D)

Weight ...................................... 3.2 kg

Standard accessories

Remote control unit .................. 1

Batteries for remote control ...... 2

RF antenna cable ..................... 1

Microphone (HR-P94K only) .... 1

• Design and specifications subject to change without notice.

4 video heads [HR-P54A] 2 video heads

UHF ch 32 – 40 adjustable (preset ch 36)

NTSC 3.58, NTSC 4.43

NTSC 3.58 NTSC 4.43 Simulated PAL (NTSC tape)

(PAL/MESECAM) More than 220 lines (NTSC)

[HR-P94K] 20 Hz to 20,000 Hz (Hi-Fi audio)

14 W [HR-P54A] 13 W

Printed in Malaysia 0800IYV*YP*PJ