JVC HR-J440U User Manual

VIDEO CASSETTE RECORDER

HR-J640U (Hi-Fi) HR-J440U (Monaural)

TV, CABLE / DBS operation – Press and hold  TV CABLE/DBS button, then press POWER, CH 5/∞, TV/VCR, 0 – 9 , ENTER

A/BTV

CABLE/DBS

POWER

TV/VCR

MBR SET

456

DAILY

WEEKLY

DISPLAY

TIMER

ENTER SP/EP

0 AUX

OSD

CANCEL

C.MEMORY

ADD

C.RESET/CH.SKIP

TV

SKIP SEARCH

VOL

REW

PLAY

REC

STOP8PAUSE

4¢

SHUTTLE PLUS

POWER

VIDEO (MONO) L – AUDIO – R

TIMER

VCR

SAP

HMS

REC PLAY PAUSE

PLAY

REW



STOP/EJECT PAUSE



REC

The VCR illustrations appearing in this instruction manual are of the HR-J640U.

INSTRUCTIONS

For Customer Use:

Enter below the Serial No. which is located on the rear of cabinet. Retain this information for future reference.  Model No. HR-J640U/HR-J440U



Serial No.

LPT0002-002A

2 EN

Dear Customer,

Thank you for purchasing the JVC VHS video cassette recorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new VCR.

Failure to heed the following precautions may result in

CAUTIONS

CAUTION



RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION:

This video cassette recorder should be used with AC 120V`, 60Hz only. To prevent electric shocks and fire hazards, DO NOT use any other power source.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

damage to the VCR, remote control or video cassette.

1. DO NOT place the VCR . . .

... in an environment prone to extreme temperatures or

humidity. ... in direct sunlight. ... in a dusty environment. ... in an environment where strong magnetic fields are

generated. ... on a surface that is unstable or subject to vibration.

2. DO NOT block the VCR’s ventilation openings.

3. DO NOT place heavy objects on the VCR or remote control.

4. DO NOT place anything which might spill on top of the VCR or remote control.

5. AVOID violent shocks to the VCR during transport.

**MOISTURE CONDENSATION

Moisture in the air will condense on the VCR when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form on the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the VCR’s power turned on for a few hours to let the moisture dry before inserting a tape.

**ABOUT HEAD CLEANING

Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or interrupted. Be sure to contact your nearest JVC dealer if such troubles occur.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

CAUTION:

Changes or modifications not approved by JVC could void user's authority to operate the equipment.

DSS

is an official trademark of DIRECTV, Inc., a unit of GM Hughes Electronics. PRIMESTAR is a registered service mark of Primestar Partners, L.P. DISH Network Echostar Communications Corporation.

n Cassettes marked "VHS" (or "S-VHS") can be used with this

video cassette recorder. However, only "VHS" recordings can be played back in this model.

n HQ VHS is compatible with existing VHS equipment.

is a trademark of

EN 3

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.

ATTENTION:

Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this booklet for future reference.

INSTALLATION

1. Grounding or Polarization

(A) Your product may be equipped with a polarized alternating-

current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

(B) Your product may be equipped with a 3-wire grounding-type

plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

2. Power Sources

Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.

3. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

4. Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

5. Ventilation

Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.

• Do not block the openings by placing the product on a bed,

sofa, rug or other similar surface.

• Do not place the product in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

6. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

ANTENNA INSTALLATION INSTRUCTIONS

1. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

2. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

3. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

ANTENNA LEAD IN WIRE

GROUND CLAMP

ANTENNA DISCHARGE UNIT (NEC SECTION 

ELECTRIC SERVICE EQUIPMENT

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

NEC – NATIONAL ELECTRICAL CODE

810-20)

GROUNDING  CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

4 EN

USE

1. Accessories

To avoid personal injury:

• Do not place this product on an unstable cart, stand, tripod, bracket, or table. It may fall, causing serious injury to a child or adult, and serious damage to the product.

• Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.

• Use a mounting accessory recommended by the manufacturer and follow the manufacturer’s instructions for any mounting of the product.

• Do not try to roll a cart with small casters across thresholds or deep-pile carpets.

2. Product and Cart Combination

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

3. Water and Moisture

Do not use this product near water—for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like.

4. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

5. Attachments

Do not use attachments not recommended by the manufacturer of this product as they may cause hazards.

6. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

7. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

PORTABLE CART WARNING (Symbol provided by RETAC)

SERVICING

1. Servicing

If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

2. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a.When the power supply cord or plug is damaged. b.If liquid has been spilled, or objects have fallen into the

product. c.If the product has been exposed to rain or water. d.If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation. e.If the product has been dropped or damaged in any way. f. When the product exhibits a distinct change in

performance—this indicates a need for service.

3. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

4. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition.

HOW TO USE THIS INSTRUCTION MANUAL

● All major sections and subsections are listed in the Table Of

Contents on page 5. Use this when searching for information

on a specific procedure or feature.

● The Index on pages 41–44 lists frequently-used terms, and

the number of the page on which they are used or explained

in the manual. This section also illustrates the controls and

connections on the front and rear panel, the front display

panel and the remote control.

● The Z mark signals a reference to another page for

instructions or related information.

● Operation buttons necessary for the various procedures are

clearly indicated through the use of illustrations at the

beginning of each major section.

BEFORE YOU INSTALL YOUR NEW VCR . . .

. . . please read the sections/literature listed below.

● ”Cautions” on page 2

● ”Important Products Safety Instructions” on the previous pages

CONTENTS

EN 5

NSTALLING YOUR NEW VCR 6

Basic Connections ..................................6

NITIAL SETTINGS 7

Plug & Play .................................................. 7

Language ..................................................... 8

Clock ............................................................ 9

Preparation ................................................................9

Semi-Auto................................................................10

Manual ....................................................................11

Auto ........................................................................ 11

Tuner .......................................................... 12

Set Receivable Channels .......................................... 12

Add Or Delete A Channel ........................................14

IMPLE PLAYBACK AND

RECORDING 15

Simple Playback ......................................... 15

Simple Recording ........................................16

LAYBACK AND RECORDING FEATURES 17

Playback Features ...................................... 17

Still Picture/Frame-By-Frame Playback.....................17

Slow Motion/Reverse Slow Motion ..........................17

Variable-Speed Search/Reverse Motion Playback .....17

High-Speed Search ..................................................17

Manual Tracking ......................................................18

Tape Position Indicator ............................................18

Video Stabilizer .......................................................19

Superimpose ............................................................ 20

Select The Soundtrack (HR-J640U Only)..................21

Index Search ............................................................ 22

Instant ReView.........................................................22

Skip Search .............................................................. 22

Repeat Playback ......................................................23

Counter Reset ..........................................................23

Counter Memory ..................................................... 23

Next-Function Memory............................................23

Auto Picture ................................................24

Preparation ..............................................................24

Playback .................................................................. 25

Recording Features .....................................26

Record One Program While

Watching Another....................................................26

Display Elapsed Recording Time..............................26

Stereo And SAP (Second Audio Program)

(HR-J640U Only) .....................................................27

To Record SAP Programs (HR-J640U Only) ..............27

IMER RECORDING 28

On-Screen Timer Programming ........... 28

Check And Cancel Programs ................................... 30

Auto Timer ......................................................31

Instant Timer Recording (ITR) .......................32

DITING 33

Edit To Another VCR .................................... 33

Edit From A Camcorder Or Another VCR ......34

PECIAL FEATURES 35

TV Multi-Brand Remote Control .............................. 35

DBS Receiver Multi-Brand Remote Control..............36

Cable Box Multi-Brand Remote Control ................... 36

Control Two JVC VCRs ............................................37

ROUBLESHOOTING 38

Power ........................................................ 38

Tape Transport ............................................38

Playback ....................................................38

Recording ...................................................38

Timer Recording ..........................................39

Other Problems .......................................... 39

UESTIONS AND ANSWERS 40

Playback ....................................................40

Recording ...................................................40

Timer Recording ..........................................40

NDEX 41

List Of Terms............................................... 41

Front View.................................................. 42

Rear View .................................................. 43

Front Display Panel..................................... 43

Remote Control ...........................................44

PECIFICATIONS 45

OR SERVICING (Only in U.S.A.) 46

F W

ARRANTY (Only in U.S.A.) 47

6 EN

VIDEO

Basic

INSTALLING YOUR NEW VCR

CHECK CONTENTS

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” (Z pg. 45).

Connections

Antenna or Cable

Coaxial Cable

Flat Feeder

AC Power Cord

Back of VCR

AC Outlet

Matching Transformer (Not supplied)

Audio Cable (not supplied)

Video Cable (not supplied)

75 ohm terminal

NOTES:

●

The VCR channel is the channel on the TV which will display the audio and video signals from the VCR. The VCR's CH3CH4 switch, on the back of the VCR, sets the VCR channel to CH3 or CH4.

●

The CH3–CH4 switch is preset to the CH3 position. Set to CH4 if CH3 is used for broadcasting in your area and set the channel on the TV to correspond to the VCR's CH3– CH4 switch setting.

●

If RF connection to TV is used, when switching from VCR to TV mode and from TV to VCR it may be necessary to issue a CH UP and then CH DOWN on TV to obtain a good quality picture.

●

Even if you are using AV cables to connect your VCR to your TV, you must also connect it using the RF cable. This will ensure that you can record one show while watching another (Z pg. 26).

●

For full identification of the VCR's rear panel, refer to the Index (REAR VIEW Z pg. 43).

ANT. IN (Antenna or Cable input)



RF OUT

RF Cable (supplied)

Back of VCR

CH3 CH4

SITUATE VCR

Place the VCR on a stable, horizontal surface.

CONNECT VCR TO TV

The connection method you use depends on the type of TV you have.

RF Connection

●

To Connect To A TV With NO AV Input Terminals . . .

a– Disconnect the TV antenna from the TV. b– Connect the TV antenna cable to the ANT. IN jack

on the rear of the VCR.

c– Connect the supplied RF cable between the RF

OUT jack on the rear of the VCR and the TV’s antenna terminal. Set TV on CH3 or CH4 corresponding to the CH3 – CH4 switch setting on the back of the VCR.

AV Connection

●

To Connect To A TV With AV Input Terminals . . .

a– Connect the antenna, VCR and TV as shown in

the illustration.

b– Connect an Audio/Video Cable between the AUDIO

OUT and VIDEO OUT jacks on the rear of the VCR and the AV IN jacks on the TV. Set your TV in video input mode or A/V input mode. Refer to the TV Instruction Manual.

For HR-J440U Owners:

If your TV has AUDIO IN L and R connectors, connect the VCR to the L connector.

CONNECT VCR TO POWER SOURCE

Connect the power plug to an AC outlet.

● The clock and tuner channels will automatically be

set when the antenna is connected and when the AC is first connected to the VCR (Z pg. 7). (If "Auto" or "CH" is displayed on the front display panel before the VCR is powered on, the clock and tuner channels are being set automatically. Wait for the time to be displayed on the front display panel before powering on the VCR.)

FINAL PREPARATION FOR USE

Power on the VCR and select the VCR channel (3 or 4) by setting the switch on the rear of the VCR as shown in the illustration. You can now perform simple playback (Z pg. 15) or simple recording (Z pg. 16).

INITIAL SETTINGS

Plug & Play

Auto Clock Set/Auto Tuner Set

IMPORTANT

● Don’t press any buttons on the VCR or remote while Plug & Play is in progress.

● If you perform Plug & Play successfully, there’s no need to perform the Clock (Z pg. 9) and Tuner (Z pg. 12) procedures. If, however, you want to add or delete channels, refer to “Add Or Delete A Channel” on page 14.

ATTENTION CABLE BOX SUBSCRIBERS

If you perform the Plug & Play procedure . . .

● Select the PBS channel on your cable box before plugging your VCR’s power plug into the AC outlet. (If you have more than one PBS channel, you may have to select an alternative PBS channel if Plug & Play is not successful.)

● If there is no PBS channel in your area, perform the Manual Clock Set procedure (Z pg. 11).

● For automatic clock adjustment to take place the VCR's power must be off and the cable box must be set to the PBS channel at clock adjustment times.

● If you perform Plug & Play successfully, D.S.T. will be set to “AUTO”. At the D.S.T. adjustment time (Z pg. 11), your VCR's power must be off and your cable box must be set to the host PBS channel in your area for the D.S.T. adjustment to take place. If the clock is not set correctly, change the D.S.T. setting to “ON” or “OFF. See step 9 of Semi-Auto procedure (Z pg. 10) or step 6 of Manual procedure (Z pg. 11).

NOTE:

If the memory backup fails, because of a power outage or because the AC was removed from the VCR, Plug & Play will be performed when power is restored to the VCR.

EN 7

The Plug & Play function sets the clock and tuner channels automatically when power is first connected to the VCR. The antenna cable must be connected for the Plug & Play function.

The time and date can be set automatically from clock setting data that is transmitted by one of the regular TV broadcast channels. We call this TV channel the “Host Channel” and it is a PBS channel in your area.

PLUG & PLAY SETUP

Connect the antenna cable to the VCR (Z pg. 6). Then connect the VCR’s power plug to an AC outlet. Do not

power on the VCR. The clock and tuner channels will automatically be set.

● Auto clock set is performed first. The auto clock set function scans all the channels received by your VCR to find the Host Channel and then sets the clock. "Auto" blinks on the front display panel during Auto clock set.

● Auto channel set is performed next. The auto channel set function scans all the channels that are receivable by your VCR. It then automatically assigns each receivable channels to the CH▲▼ buttons. It skips non-receivable channels. During auto channel set the channel numbers are displayed as they are scanned and set.

● When Plug & Play has been completed successfully the correct time is displayed.

● If "AUTO CLOCK SET" or "SEMI-AUTO CLOCK SET" is selected at the Override Auto Clock Set screen on page 10, the clock will be adjusted automatically by the Host PBS every hour on the hour (except for 11:00 PM, midnight, 1:00 AM and 2:00 AM) by the incoming PBS channel clock setting data. (This automatic clock adjustment can only be performed when the VCR’s power is turned off. The clock will be adjusted on the hour based on the time displayed on the VCR, not on the actual real time.) The default setting is "AUTO CLOCK SET".

● If an incorrect time is displayed on the front display panel, you may be receiving the clock setting data of a PBS channel from an adjacent time zone, or an incorrect PBS channel from a cable TV system. In this case, perform the Semi-Auto (Z pg. 10) or Manual Clock Set (Z pg. 11) procedure. Auto channel set has already taken place and it need not be set again.

● If “- -:- -” appears on the display, your antenna cable may not be connected to the VCR, there may not be a Host PBS signal available in your area, or your cable box may not be set to the PBS channel. Ensure that the antenna cable is connected correctly. If you use a cable box ensure that your local PBS is selected on your cable box (Z ATTENTION CABLE BOX SUBSCRIBERS). Then power on and power off the VCR; the Plug & Play function will be automatically reactivated and "Auto" will be displayed on the VCR's front panel. If everything is connected and set correctly, perform the Manual Clock Set procedure (Z pg. 11). Auto channel set has not yet taken place, so please also perform the “Set Receivable Channels” procedure (Z pg. 12).

During Initial Auto Clock Set

"Auto" blinks.

During Auto Channel Set

The channel numbers are displayed as they are scanned and set.

Plug & Play Completed

The current time (including AM/PM) is displayed.

8 EN

POWER

CH5∞

Language

INITIAL SETTINGS (cont.)

This VCR offers you the choice to view on-screen messages in English, Spanish or French (not including messages superimposed on the TV picture). Select the desired language using this procedure. The default setting is "ENGLISH".

Turn on the TV and select the VCR channel 3 or 4 (or AV mode).

POWER

456

TURN ON THE VCR

Press POWER.

ACCESS ON-SCREEN MENU

Press MENU.

ACCESS CUSTOM SET SCREEN

At the Main Menu screen, move the highlight bar

(arrow) to “CUSTOM SET” by pressing CH5∞ or

SHUTTLE PLUS %ﬁ, then press OK.

ACCESS LANGUAGE SELECT SCREEN

The messages are preset to appear in English. If you want

to see them in Spanish or French, move the highlight bar (arrow) to “LANGUAGE SELECT” by pressing CH5∞ or SHUTTLE PLUS %ﬁ, then press OK.

MAIN MENU

PROGRAM SET FUNCTION SET TUNER SET

=CUSTOM SET

AUTO PICTURE VIDEO STABILIZER PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

CUSTOM SET

OVERRIDE

AUTO CLOCK SET

=LANGUAGE SELECT

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

4¢

SHUTTLE PLUS

CH5∞

%ﬁ

SELECT LANGUAGE

At the Language Select screen, move the highlight

bar (arrow) to the desired language by pressing CH5∞ or SHUTTLE PLUS

ﬁ, then press MENU as

many times as necessary to return to the normal screen.

LANGUAGE SELECT

=ENGLISH

ESPAÑOL FRANCAIS

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

Clock

POWER

EN 9

Perform clock setting only if the clock has not been set correctly by the Plug & Play function. Access the Override Auto Clock Set screen to choose the Auto, Semi-Auto or Manual clock setting procedure. Each procedure starts from step 5. *Auto need only be selected if Semi-Auto or Manual had previously been selected.

Turn on the TV and select the VCR channel 3 or 4 (or AV mode).

POWER

456

Preparation

TURN ON THE VCR

Press POWER.

ACCESS ON-SCREEN MENU

Press MENU.

ACCESS CUSTOM SET SCREEN

At the Main Menu screen, move the highlight bar

(arrow) to “CUSTOM SET” by pressing CH5∞ or SHUTTLE PLUS %ﬁ, then press OK.

ACCESS CLOCK SET MODE SELECT SCREEN

Move the highlight bar (arrow) at the Custom Set

screen to “OVERRIDE AUTO CLOCK SET” by pressing CH5∞ or

SHUTTLE PLUS %ﬁ, then press OK.

PROGRAM SET FUNCTION SET TUNER SET

=CUSTOM SET

AUTO PICTURE VIDEO STABILIZER PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

=OVERRIDE

AUTO CLOCK SET

LANGUAGE SELECT

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

MAIN MENU

CUSTOM SET

4¢

SHUTTLE PLUS

10 EN

SHUTTLE PLUS

456

4¢

INITIAL SETTINGS (cont.)

Semi-Auto

SELECT MODE

At the Override Auto Clock Set screen, move the

highlight bar (arrow) to “SEMI-AUTO CLOCK SET” by pressing CH▲▼ or

SHUTTLE PLUS %ﬁ, then press OK.

OVERRIDE AUTO CLOCK SET

AUTO CLOCK SET

=SEMI–AUTO CLOCK SET

MANUAL CLOCK SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

ACCESS SELECT SCREENS

At the Semi-Auto Clock Set screen, move the highlight

bar (arrow) to the desired mode by pressing CH▲▼ or SHUTTLE PLUS %ﬁ, then press OK.

To select the Host Channel — step 7 To select the Time Zone — step 8 To select the D.S.T. mode — step 9

NOTE:

The time that has been set previously by the Plug & Play function will be erased when any of the three settings mentioned above is changed.

SEMI–AUTO CLOCK SET

=HOST CHANNEL SELECT

TIME ZONE SELECT D.S.T. SELECT

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

SELECT HOST CHANNEL

You can either select "AUTO", or enter a PBS

channel number. For automatic selection, press MENU if "AUTO" is highlighted on the Host Channel Select screen. To manually select "AUTO" or the PBS channel, press CH▲▼ or SHUTTLE PLUS %ﬁ to cycle through "AUTO" or the channel numbers (hold button down to speed through numbers) and stop when the desired number appears. Press MENU and the Semi-Auto Clock Set screen reappears.

HOST CHANNEL SELECT

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

(CATV)

CH AUTO

NOTES:

●

For cable box users: Select "AUTO" or the channel on your VCR that receives the cable box channels, and set the cable box to the PBS channel.

●

There are some PBS channels that do not transmit clock setting data.

EN 11

SELECT TIME ZONE

You can select the zone automatically or manually

by pressing CH▲▼ or SHUTTLE PLUS %ﬁ. If an

incorrect time is displayed you may be receiving the clock setting data of a PBS channel from an adjacent time zone or from an incorrect PBS channel from a cable TV system. If you selected "AUTO" in step 7 select "MANUAL" and select the correct time zone manually.

● If you selected "AUTO", press MENU to return to the

Semi-Auto Clock Set screen.

● If you selected

"MANUAL", press OK and the screen to the right appears. Move the highlight bar (arrow) to your choice by pressing

CH▲▼ or SHUTTLE PLUS %ﬁ, then press MENU twice to return to

the Semi-Auto Clock Set screen.

TIME ZONE SELECT

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

TIME ZONE SELECT

=ATLANTIC

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

SELECT D.S.T. MODE

You have three choices:

a–Select “AUTO” and the

adjustment to your VCR’s clock will be made according to the incoming signal from the host channel. b–Select “ON” and the adjustment will be made based on the clock itself. c–Select “OFF” if Daylight Saving Time doesn’t apply to you. Move the highlight bar (arrow) to your choice by pressing CH MENU and the Semi-Auto Clock Set screen reappears.

or SHUTTLE PLUS

∞

D.S.T. SELECT

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

=AUTO

MANUAL

EASTERN CENTRAL MOUNTAIN PACIFIC ALASKA HAWAII

=AUTO

ON OFF

, then press

ﬁ

Manual

SELECT MODE

At the Override Auto Clock Set screen (Z pg. 10), move the highlight bar (arrow) to “MANUAL CLOCK SET” by

pressing CH▲▼ or SHUTTLE PLUS %ﬁ, then press OK.

SET DATE, TIME AND D.S.T.

The Manual Clock Set screen is displayed and the

month digit begins blinking. Press the appropriate NUMBER keys to set the date and time (if only 1 digit, press "0" first). Press CH▲▼ or SHUTTLE PLUS %ﬁ to set AM/PM and D.S.T. (Daylight Saving Time). Press OK after AM/ PM and D.S.T. settings. Set D.S.T. to "ON" to set the D.S.T. according to the VCR's clock or to "OFF" if D.S.T. doesn't apply to you.

When you’re finished with this set-up procedure, press MENU to start the clock.

NOTES:

●

CH▲▼ and SHUTTLE PLUS

perform all operations. (In this case, press OK after each setting.)

●

At the Manual Clock Set screen, the setting that can be set blinks. When setting of a highlighted item is completed, the highlight bar moves down by 1 line to the next item.

MANUAL CLOCK SET

DATE 1/ 1/97 WED

TIME – –:– – AM D.S.T. ON

PRESS NUMBER KEY (O–9)

OR (5,∞), THEN (OK)

PRESS (MENU) TO END

can be used to

ﬁ

MAKE CORRECTIONS

To change any of the settings, press OK or SHUTTLE

ﬁ

PLUS until the item you want to change blinks, then

set as in step 6.

Auto

IMPORTANT

Turn the VCR off after performing the Semi-Auto Clock Set procedure. "Auto" will appear on the front display panel when the clock is being set. The current time will appear automatically when the clock is set.

SELECT MODE

At the Override Auto Clock Set screen, move the highlight bar (arrow) to "AUTO CLOCK SET" by

pressing CH▲▼ or SHUTTLE PLUS %ﬁ, then power off the VCR. Do not power it on again until the clock has been adjusted. The clock is automatically adjusted on the hour except at 11:00 PM, midnight, 1:00 AM and 2:00 AM. (The clock will be adjusted on the hour based on the time displayed on the VCR, not on the actual real time.)

**AUTO DAYLIGHT SAVING TIME

This function enables automatic adjustment of the VCR’s clock at the start and end of Daylight Saving Time. With Auto DST activated, . . . . . . on the first Sunday of April at 2:00 AM, the clock is

adjusted to 3:00 AM.

. . . on the last Sunday of October at 2:00 AM, the clock is

adjusted to 1:00 AM.

12 EN

POWER

INITIAL SETTINGS (cont.)

Set Receivable Channels

Tuner

Turn on the TV and select the VCR channel 3 or 4 (or AV mode).

POWER

SHUTTLE PLUS

456

4¢

TURN ON THE VCR

Press POWER.

ACCESS MAIN MENU SCREEN

Press MENU.

ACCESS TUNER SET SCREEN

Move the highlight bar (arrow) to "TUNER SET" by

pressing CH5∞ or SHUTTLE PLUS %ﬁ, then press OK.

PERFORM AUTO CHANNEL SET

Move the highlight bar (arrow) to "AUTO

CHANNEL SET" by pressing CH5∞ or

SHUTTLE PLUS %ﬁ, then press OK.

● Receivable channels in

your area are automatically assigned to the CH5∞ buttons, and non-receivable channels are skipped.

NOTES:

●

At the end of Auto Channel Set, “SCAN COMPLETED” appears on screen.

●

If the scan was unsuccessful, “SCAN COMPLETED– NO SIGNAL” appears on screen. Check the connections and start again.

PROGRAM SET FUNCTION SET

=TUNER SET

CUSTOM SET AUTO PICTURE VIDEO STABILIZER PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

BAND AFC

=AUTO CHANNEL SET

MANUAL CHANNEL SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

AUTO CHANNEL SET

PRESS (MENU) TO END

MAIN MENU

TUNER SET

SCANNING...

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

EN 13

INFORMATION

The VCR detects the band (TV or CATV) and selects the correct band automatically during Auto Channel Set. If necessary, you can check the setting at the Band screen.

● At the Tuner Set screen, move the highlight bar (arrow) to

"BAND" by pressing CH5∞ or SHUTTLE PLUS %ﬁ, then press OK.

TUNER SET

=BAND

AFC AUTO CHANNEL SET MANUAL CHANNEL SET

BAND

=CATV

456

4¢

SHUTTLE PLUS

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

● Press MENU as many times as necessary to return to the

normal screen.

14 EN

ADD

CH.SKIP

SHUTTLE PLUS

456

4¢

NUMBER

INITIAL SETTINGS (cont.)

Add Or Delete A Channel

ACCESS TUNER SET SCREEN

Access by performing steps 2 and 3 of the Tuner procedure on page 12.

● To add a channel, go to step 2.

● To delete a channel, skip to step 4.

ACCESS AFC SCREEN

Move the highlight bar (arrow) to "AFC" by pressing

CH5∞ or SHUTTLE PLUS %ﬁ, then press OK.

MAKE SELECTION

Move the highlight bar (arrow) to "SPCL" by

pressing CH5∞ or SHUTTLE PLUS %ﬁ, then

press MENU to return to the Tuner Set screen.

● AFC set to SPCL (special)

is necessary for tuning on certain CATV systems.

ACCESS MANUAL CHANNEL SET SCREEN

Move the highlight bar (arrow) to "MANUAL CHANNEL SET" by pressing CH5∞ or SHUTTLE PLUS %ﬁ, then

press OK.

STORE OR SKIP DESIRED CHANNEL

Input the channel number using the NUMBER keys or

by pressing CH5∞ or SHUTTLE PLUS %ﬁ, then press ADD to add or CH.SKIP to delete. Repeat

for each channel you want to store or skip.

AFC

NORM

=SPCL

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

MANUAL CHANNEL SET

(CATV)

CH 125 ADD

SELECT CH NO. ADD PRESS (ADD/SKIP) PRESS (MENU) TO END

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

SIMPLE PLAYBACK AND RECORDING

STOP/EJECT

PLAY

REW

PLAY

STOP

Simple

Playback

Turn on the TV and select the VCR channel 3 or 4 (or AV mode).

3 4

EN 15

LOAD A CASSETTE

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. Don’t apply too much pressure when inserting.

● The VCR’s power comes on automatically.

● The counter is automatically reset to "0H 00M 00S".

● If the cassette's record safety tab has been removed,

playback begins automatically.

FIND PROGRAM START POINT

Press REW or FF if you want to rewind or fast forward to a different section of the tape.

START PLAYBACK

Press PLAY. "AUTO PICTURE" appears on screen (Z pg. 25).

STOP PLAYBACK

Press STOP or STOP/EJECT. Then press STOP/EJECT to remove the cassette.

REW (Rewind)

456

4¢

FF (Fast-Forward)

Usable cassettes

Full-Size VHS T-30 (ST-30**) T-60 (ST-60**) T-90 T-120 (ST-120**) T-160 (ST-160**) ST-210**

Compact VHS* TC-20 (ST-C20**) TC-30 (ST-C30**) TC-40 (ST-C40**)

* Compact VHS camcorder recordings can be played on

this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.

** This video recorder can record on regular VHS and

Super VHS cassettes. However, it will record and play back regular VHS signals only. It is not possible to play back Super VHS recordings.

+ 33 hidden pages