JVC HR-J347EM User Manual

VIDEO CASSETTE RECORDER

HR-J347EM

TV/VCR

(MONITOR)

DISPLAY

123

/ADD TIME

CANCEL

/DAILY

WEEKLY

/C.RESET

/AUX

PROG CHECK

4 TIMER

EXPRESS PROGRAMMING

TV PROG

DATESTOPSTART

REW

PLAY

REC

STOP

PAUSE

TV VOL

PROG

/MENU

4¢

C.MEMORY

PUSH JOG

Press and hold TV button while pressing , TV PROG. + / –, TV / VCR

TV VOL

POWER

DISPLAY

AUTO SP/LP TIMER

REVIEW

SPLPEP

V C R

INSTRUCTIONS

COLOUR SYSTEM

TV

PROG

INTELLIGENT

PICTURE

PAL

ENGLISH

CONTENTS

SAFETY FIRST 2

Safety Precautions ...................... 2

INSTALLING YOUR NEW RECORDER 3

Basic Connections......................3

INITIAL SETTINGS 4

Auto Set Up ............................... 4

Video Channel Set...................... 5

Select Language ......................... 6

Select Television System ............. 7

Clock Set.................................... 8

On-Screen Displays.................... 9

PLAYBACK 10

Basic Playback ......................... 10

Playback Features..................... 11

RECORDING 14

Basic Recording ....................... 14

Recording Features................... 15

TIMER RECORDING 16

Timer Programming.................. 16

EDITING 20

Edit To Or From Another Video

Recorder .................................. 20

Edit From A Camcorder............ 21

INFORMATION ON MULTI-SYSTEM COMPATIBILITY 22

TUNER SET 24 TROUBLESHOOTING 28 QUESTIONS AND ANSWERS 30 INDEX 31 SPECIFICATIONS 34

LPT0002-0G4A

2 EN

SAFETY FIRST

Safety Precautions

The rating plate and the safety caution are on the rear of the unit.

WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

CAUTION

n When you are not using the recorder for a long period of

time, it is recommended that you disconnect the power cord from the mains outlet.

n Dangerous voltage inside. Refer internal servicing to

qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial.

n Use the conversion plug depending on the type of your

AC wall outlet.

IMPORTANT

1.In addition to PAL B/G, D/K colour television signals, this recorder can also receive SECAM B/G, D/K colour television signals. SECAM B/G, D/K colour television signals can be recorded and played back in colour as far as this same recorder is used for recording and playback.

2.SECAM B/G, D/K colour television signals recorded on this recorder produce monochrome pictures if played back on another PAL or SECAM recorder.

3.SECAM B/G, D/K colour television signals recorded on another PAL or SECAM recorder produce monochrome pictures if played back on this recorder.

4.This recorder cannot be used in France. Use in France a recorder which is capable of receiving SECAM L colour television signals.

5.SECAM L prerecorded cassettes or recordings made with a SECAM L video recorder produce monochrome pictures when played back on this recorder.

POWER SYSTEM

This set operates on voltage of AC110 – 240 V` (Rating), AC90 – 260 V` (Operating), 50/60 Hz with automatic switching.

IMPORTANT

n Please read the various precautions on this page before

installing or operating the recorder.

n It should be noted that it may be unlawful to re-record

pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein.

The POWER mains power from the unit, but switches operating current

on and off. " shows ON.

Failure to heed the following precautions may result in damage to the recorder, remote control or video cassette.

1. DO NOT place the recorder . . .

... in an environment prone to extreme temperatures or

humidity. ... in direct sunlight. ... in a dusty environment. ... in an environment where strong magnetic fields are

generated. ... on a surface that is unstable or subject to vibration.

2. DO NOT block the recorder’s ventilation openings.

3. DO NOT place heavy objects on the recorder or remote control.

4. DO NOT place anything which might spill on top of the recorder or remote control.

5. AVOID violent shocks to the recorder during transport.

button does not completely shut off

" shows electrical power standby and " "

Warning on lithium battery

The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100°C or incinerate. Replace battery with Panasonic (Matsushita Electric), Sanyo, Sony or Maxell CR2025; use of another battery may present a risk of fire or explosion.

n Dispose of used battery promptly. n Keep away from children. n Do not disassemble and do not dispose of in fire.

PAL

n Only cassettes marked "VHS" can be used with this

videorecorder.

n HQ VHS is compatible with existing VHS equipment.

MOISTURE CONDENSATION

Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form in the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the recorder turned on for a few hours to let the moisture dry.

ABOUT HEAD CLEANING

Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or interrupted. Be sure to contact your nearest JVC dealer if such troubles occur.

INSTALLING YOUR NEW RECORDER

It's essential that your video recorder be properly connected. Follow these steps carefully. THESE STEPS MUST BE COM-

Basic

PLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.

EN 3

Connections

Aerial terminal

Back of TV

AV-IN terminals

AV Cable (not provided)

Mains Power Cord

Rear View

RF Cable (provided)

CHECK CONTENTS

Make sure the package contains all of the accessories listed in “Specifications” (Z pg. 34).

SITUATE RECORDER

Place the recorder on a stable, horizontal surface.

CONNECT RECORDER TO TV

The connection method you use depends on the type

TV Aerial Cable



of TV you have.

RF CONNECTION

●

To Connect To A TV With NO AV Input Terminals . . .

a– Disconnect the TV aerial cable from the TV. b– Connect the TV aerial cable to the ANT. IN jack

on the rear panel of the recorder.

c– Connect the provided RF cable between the RF

OUT jack on the rear panel of the recorder and the TV’s aerial terminal.

Before operating the recorder, make sure the TV’s channel is set to the VIDEO channel (

Z pg. 5).

AV CONNECTION

●

To Connect To A TV With AV Input Terminals . . .

a– Connect the aerial, recorder and TV as per “RF

CONNECTION”.

b– Connect an optional AV cable between the

AUDIO OUT and VIDEO OUT connectors on the rear panel of the recorder and the TV’s AV-IN terminals .

Before operating the recorder, make sure the TV is set to the VIDEO (or AV) mode.

Mains outlet

AUDIO OUT/ VIDEO OUT

Connect the power plug to an AC outlet before installing the lithium battery. Z pg. 5

RF output channel adjustment screw

CONNECT RECORDER TO MAINS

Plug the end of the mains power cord into a mains outlet.

NOTE:

Use the conversion plug depending on the type of your AC wall outlet.

After you plug the mains power cord into a mains outlet, the Auto Set Up display appears on the TV screen and/or on the recorder's front display panel when the button on the recorder/remote control is pressed for the first time to power on the recorder Z pg. 4.

4 EN

Auto Set Up

Auto Channel Set

123

456

ATTENTION

Once you have performed Auto Set Up, even if the recorder's memory backup has expired, all the stored stations remain in the recorder's memory and the recorder will not perform Auto Set Up again. If you have moved to a different area or a new station starts broadcasting in your area, perform tuner setting. Z pg. 24

INITIAL SETTINGS

When the button on the recorder/remote control is pressed for the first time to power on the recorder after you plug the mains power cord into a mains outlet, the Auto Set Up function sets the tuner channels automatically. You can refer to the front display panel and/or the on-screen display to perform this procedure.

Before starting, make sure of the following:

● The TV aerial cable should be connected to the recorder.

● The recorder's mains power cord should be connected to

a mains outlet. Z pg. 3

● If you want to use the on-screen display, the TV should

be set to its AV mode (with AV connection Z pg. 3) or UHF channel 36 (with RF connection Z pg. 3).

START AUTO SET UP

Press .

● The Auto Set Up function scans all the channels that

are receivable by your recorder. It then automatically assigns each receivable channels to the TV PROG buttons. It skips non-receivable channels.

● As Auto Set Up progresses, the " screen moves from left to right.

● After you perform Auto Set Up, if the tuner channels have not been set properly or if "CH – –" is displayed on the front display panel, make sure that the aerial cable is connected to the recorder properly and turn off the recorder power once, and turn the power back on to try Auto Set Up again.

● If there is a power cut, or if you press while Auto Set Up is in progress, Auto Set Up will be interrupted; be sure to turn off the recorder power once and try again.

" mark on the

or MENU

DO NOT press any button on the recorder or remote control while Auto Set Up is in progress.

AUTO CH SET

On-Screen Display

During Auto Set Up

The channel numbers are displayed as they are scanned and set.

PLEASE WAIT

START FINISH

When Auto Set Up is completed, the lowest position number will appear on the front display panel.

TV Screen

Front Display Panel

NOTE:

If you want to set the tuner manually such as to add or skip channels, to swap channel positions, or to fine-tune channels, pg. 25.

Video

STOP/EJECT

Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

TEST SIGNAL

The channel on which the screen to the left appear clearly in step 3 is your Video Channel.

EN 5

The video recorder is designed to send picture and sound signals via the connected RF cable to your TV on UHF channel 36; if you want to change this Video Channel to another channel between 32 and 40, perform the following steps.

Before starting, make sure of the following:

● The recorder's power should be off.

● No cassette should be inserted in the recorder.

● The connected TV's power should be on.

SET TV CHANNEL

Set your TV to a channel between 32 and 40 that you want to use as the Video Channel on the TV.

BRING TEST SIGNAL ON SCREEN

Hold down the recorder's STOP/EJECT button for more than 5 seconds.

● Two vertical bars appear on the screen.

TUNE YOUR RECORDER

Turn the RF output channel adjustment screw on the rear panel of the recorder by using a screwdriver until

the two vertical bars become as clear as they can be.

EXIT VIDEO CHANNEL SET MODE

Press the recorder's STOP/EJECT button again to finish the setting.

To view picture signals from the video recorder, set your TV to the Video Channel.

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Be sure to connect the power plug to an AC outlet first before installing the lithium battery; otherwise, the battery's service life will be drastically shortened.



Installing/Removing the lithium battery

Make sure that the power plug is connected to an AC outlet

and turn off the VCR power.

2 Open the battery cover while pressing the release tab as

illustrated.

3 Insert a lithium battery with the plus (+) side up and push it

in.

● To remove the lithium battery, press the latch A down-

ward using a pointed non-metallic object, then pull out the lithium battery.

4 Close the battery cover until it clicks in place.

6 EN

Select

INITIAL SETTINGS (cont.)

TURN ON THE RECORDER

Press .

Language

Turn on the TV and select the VIDEO channel (or AV mode).

123

456

4¢

PUSH JOG

ACCESS MAIN MENU SCREEN

Press MENU twice.

ACCESS INITIAL SET SCREEN

Press PUSH JOG %ﬁ to place the pointer next to

"INITIAL SET", then press OK.

ACCESS LANGUAGE SELECT SCREEN

Press PUSH JOG %ﬁ to place the pointer next to

"LANGUAGE SELECT", then press OK.

MAIN MENU FUNCTION SET TUNER SET INITIAL SET

[5/∞] = [MENU] : EXIT

INITIAL SET CLOCK SET

LANGUAGE SELECT TV SYSTEM SELECT

[5/∞] = [MENU] : EXIT

SELECT LANGUAGE

Place the pointer next to the language of your choice (English or Russian or Arabic) by pressing PUSH JOG

%ﬁ, then press OK.

RETURN TO NORMAL SCREEN

Press MENU.

Select

EN 7

TURN ON THE RECORDER

Press .

Television System

Turn on the TV and select the VIDEO channel (or AV mode).

123

456

4¢

PUSH JOG

ACCESS MAIN MENU SCREEN

Press MENU twice.

ACCESS INITIAL SET SCREEN

Press PUSH JOG %ﬁ to place the pointer next to

"INITIAL SET", then press OK.

ACCESS TV SYSTEM SELECT SCREEN

Press PUSH JOG %ﬁ to place the pointer next to

"TV SYSTEM SELECT", then press OK.

SELECT TELEVISION SYSTEM

Place the pointer next to the appropriate TV system

that matches the system of TV being used (refer to the table to the left). Then press OK.

MAIN MENU FUNCTION SET TUNER SET INITIAL SET

[5/∞] = [MENU] : EXIT

INITIAL SET CLOCK SET

LANGUAGE SELECT TV SYSTEM SELECT

[5/∞] = [MENU] : EXIT

TV SYSTEM SELECT

[5/∞] = [MENU] : EXIT

B/G D/K I

Major Countries TV System

Kuwait, U.A.E, Indonesia, Singapore, Thailand, Malaysia, Iran, Saudi Arabia, B/G Egypt, Morocco, Lebanon, Iraq

China, Mongolia, Russia D/K Hong Kong I

RETURN TO NORMAL SCREEN

Press MENU.

NOTES:

●

If no colours appear on the screen when using a multi-system television with its system select switch set to AUTO, change the TV system setting of the recorder.

●

For more information on multi-system compatibility.

p.22

8 EN

STOP+/–

DATE+/–

INITIAL SETTINGS (cont.)

Preparation

Clock Set

Turn on the TV and select the VIDEO channel (or AV mode).

123

456

START+/–

4¢

PUSH JOG

TURN THE RECORDER ON

Press .

ACCESS MAIN MENU SCREEN

Press MENU twice.

ACCESS INITIAL SET SCREEN

Press PUSH JOG %ﬁ to place the pointer next to

"INITIAL SET", then press OK.

ACCESS CLOCK SET SCREEN

Press PUSH JOG %ﬁ to place the pointer next to "CLOCK SET", then press OK. The Clock Set screen

appears.

INITIAL SET

CLOCK SET LANGUAGE SELECT TV SYSTEM SELECT

FUNCTION SET TUNER SET INITIAL SET

[5/∞] = [MENU] : EXIT

TIME DATE YEAR 00: 00 01 . 01 00

MAIN MENU

CLOCK SET

NOTES:

●

If the day and month data are invalid (such as 31st April), the month digits are cleared automatically and the day digits begin blinking. Input the correct data.

●

If the year digits are automatically cleared and the day digits begin blinking, it is possible that you have input 29th February for a non-leap year. Input the correct data.

[5/∞] = [MENU] : EXIT

[+/–] = [MENU] : EXIT

SET TIME

Press START +/– to set the time.

● Press and hold either button to delay or advance the

time by 30 minutes.

SET DATE

Press STOP +/– to set the date.

● Press and hold either button to change the date by 15

days.

SET YEAR

Press DATE +/– to set the year.

START CLOCK OPERATION

Press MENU.

EN 9

You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF.

On-Screen Displays

Turn on the TV and select the VIDEO channel (or AV mode).

123

456

NOTES:

●

When you use this recorder as the player for editing, be sure to set "O.S.D." to "OFF" before starting.

●

During playback, the operation mode indicators may be disturbed depending on the type of tape being used.

4¢

PUSH JOG

TURN ON THE RECORDER

Press .

ACCESS MAIN MENU SCREEN

Press MENU twice.

ACCESS FUNCTION SET SCREEN

Place the pointer next to "FUNCTION SET" by pressing

PUSH JOG %ﬁ, then press OK.

ACCESS O.S.D. SCREEN

Place the pointer next to "O.S.D." by pressing PUSH

JOG %ﬁ, then press OK.

AUTO TIMER O.S.D.

[5/∞] = [MENU] : EXIT

ENABLE/DISABLE ON-SCREEN DISPLAY

The default setting is “ON”, so if you want on-

screen displays, leave the setting as it is and go to step 6. If you don’t want the displays to appear, press PUSH JOG %ﬁ to place the pointer next to "OFF", then press OK.

[5/∞] = [MENU] : EXIT

RETURN TO NORMAL

Press MENU.

FUNCTION SET

O.S.D.

ON OFF

The superimposed indication on the TV screen tells you what the recorder is doing.

2 4

PR. 12 ]SP 21 : 00 MESECAM

24. 12. 97 I. PICTURE

OFF

M –1 : 23 : 45

11 10

6 8

1– Operation mode indicators 2– Channel position number/Aux. indicator (AUX) 3– Cassette loaded mark 4– Clock display 5– Current day/month/year 6– Tape direction 7– Tape position indicator (Z pg. 13) 8– Counter display (including Counter Memory indicator) 9– Intelligent picture indicator (Z pg. 12) 10– Colour system indicator (Z pg. 22) 11– Tape speed SP/LP/EP

10 EN

PLAY

STOP/EJECT

STOP

PLAY

COLOUR SYSTEM

REW

Basic

PLAYBACK

The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.

Playback

Turn on the TV and select the VIDEO channel (or AV mode).

123

456

LOAD A CASSETTE

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is

point toward the recorder. Don’t apply too much pressure when inserting.

● The recorder power comes on automatically and the counter is reset to 0:00:00.

● Select the appropriate colour system by pressing the COLOUR SYSTEM button.(Z pg. 22)

● If the record safety tab has been removed, playback begins automatically.

FIND PROGRAMME START POINT

If the tape is advanced past the start point, press REW. To go forward, press FF.

START PLAYBACK

Press PLAY.

STOP PLAYBACK

Press STOP on the remote or STOP/EJECT on the recorder’s front panel. Then press STOP/EJECT to

remove the cassette.

Usable cassettes

REW

4¢

● Compact VHS camcorder recordings can be played on this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.

● This video recorder can record on regular VHS and Super VHS cassettes. However, it will record and play back regular VHS signals only. It is not possible to play back a recorded Super VHS tape.

EN 11

PLAY

REW

TV PROG

Take advantage of special functions possible with the recorder’s controls or the remote control.

Playback Features

REW

4¢

TV PROG

PAUSE

PUSH JOG

High-Speed Search

ACTIVATE HIGH-SPEED SEARCH

During playback or still, press FF for forward highspeed search, or REW for reverse high-speed search.

To resume normal playback, press PLAY.

Still Picture/Frame-By-Frame Playback

PAUSE DURING PLAYBACK

Press PAUSE. If there is vertical jitter, use the TV PROG buttons to correct the picture.

ACTIVATE FRAME-BY-FRAME PLAYBACK

Press PAUSE.

Press PUSH JOG or .

To resume normal playback, press PLAY.

Variable-Speed Search

ACTIVATE VARIABLE-SPEED SEARCH

During playback, press PUSH JOG or .

● The more times you press, the faster the playback

To resume normal playback, press PLAY.

picture moves.

● To decrease speed, press the button for the opposite direction.

Slow Motion

ACTIVATE SLOW-MOTION PLAYBACK

During still picture, press and hold PAUSE for 2 seconds, then release. Press and release again to return

to still picture.

During still picture, press and hold PUSH JOG or . Release to return to still picture.

To resume normal playback, press PLAY.

NOTES:

●

For short searches, press and hold FF or REW for over 2 seconds. When released, normal playback resumes.

●

In the search, still, or frame by frame playback mode, the picture may be distorted, and there may be a loss of colour; with SP recordings, noise may also appear in the picture.

+ 23 hidden pages