JVC HR-E239EG, HR-E439EG User Manual

VIDEO CASSETTE RECORDER
HR-E439EG HR-E239EG
OPERATE
CH SET
STORE
C.MEMORY
A
B
MODECLOCK
DISPLAY
2
12453
ADD TIME
6
DAILY
WEEKLY
9
807
AUX
C.RESET
CANCEL
TIMER
TV
DATESTOP
START
PROG.
EXPRESS PROGRAMMING
AUDIO MONITOR
TV/VIDEO
TV VCR
(MONITOR)
P
R
R
E
O
D
G
N
I
C
F
H
E
E
N
C
E
K
C
S
3
G
O
O
K
R
P
O
V
L
.
V
T
1
PUSH JOG
E
D
I
I
L
U
L
G
U
I
M
MULTI BRAND
REMOTE CONTROL UNIT
OPERATE TIMER
+
AUTO SP/LP
TV PROG
SP/LP
TIMER
The recorder illustrations appering in this instruction manual are of the HR-E439EG.
INSTRUCTIONS
VIDEO
REMAIN
D
W
SP LP
I TR
D
EP
M
AUDIO
DUBBING
FF
REW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
TV PROG./
0
0
0
0
0
JOG
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SHUTTLE
0
0
PAL
ENGLISH
CONTENTS
SAFETY FIRST 2
Safety Precautions ....................................2
INSTALLING YOUR NEW RECORDER 3
Basic Connections ................................... 3
Tune The TV To Your Video Recorder ...... 3
Connecting/Using A Decoder .................. 4
INITIAL SETTINGS 5
Tuner Set.................................................. 5
Clock Set ................................................. 7
PLAYBACK 9
Basic Playback .........................................9
Playback Features .................................. 10
Basic Recording ..................................... 15
B.E.S.T. Picture System........................... 16
On-Screen Displays ............................... 18
Recording Features ................................ 19
Information On ShowView .................... 20
Guide Prog. Number Set ..................... 20
When Using A Satellite Tuner .............. 21
ShowView Timer Recording................... 22
Regular Timer Programming .................. 24
Check And Cancel Programmes .......... 26
Auto SP/LP Timer [E439EG only]......... 26
PDC/VPS Recording ............................ 26
Timer Warning .................................... 26
EDITING 27
Audio Dubbing [E439EG only] .............. 27
Edit To Or From Another Video
Recorder ................................................ 28
Edit From A Camcorder ......................... 29
REMOTE CONTROL 30
Multi-Brand Remote Control .................. 30
USING THE CONFIRMATION SCREEN 31
Storing Channels Manually .................... 31
Delete A Channel .................................. 31
Change Station Channel Position ........... 31
Set Stations ............................................ 32
Fine-Tuning Channels Already Stored .... 32
PU30425-1895-1
EN
2 EN
SAFETY FIRST
Safety Precautions
The rating plate and the safety caution are on the rear of the unit.
WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
CAUTION
n When you are not using the recorder for a long period of
time, it is recommended that you disconnect the power cord from the mains outlet.
n Dangerous voltage inside. Refer internal servicing to
qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial.
WARNING
There are two different types of SECAM colour systems: SECAM-L, used in FRANCE (also called SECAM-West), and SECAM-B, used in Eastern European countries (also called SECAM-East).
1.This recorder can also receive SECAM-B colour television signals for recording and playback.
2.Recordings made of SECAM-B television signals produce monochrome pictures if played back on a video recorder of SECAM-L standard, or do not produce normal colour pictures if played back on a PAL video recorder with SECAM-B system incorporated (even if the TV set is SECAM-compatible).
3.SECAM-L prerecorded cassettes or recordings made with a SECAM-L video recorder produce monochrome pictures when played back with this recorder.
4.This recorder cannot be used for the SECAM-L standard. Use a SECAM-L recorder to record SECAM-L signals.
IMPORTANT
n Please read the various precautions on this page before
installing or operating the recorder.
n It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video record­ing, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein.
The OPERATE button does not completely shut off mains power from the unit, but switches operating current on and off.
To E439EG Owners:
Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a single-speed video recorder.
Failure to heed the following precautions may result in damage to the recorder, remote control or video cassette.
1. DO NOT place the recorder . . .
... in an environment prone to extreme temperatures or
humidity. ... in direct sunlight. ... in a dusty environment. ... in an environment where strong magnetic fields are
generated. ... on a surface that is unstable or subject to vibration.
For Italy:
"It is declared that this product, brand JVC, conforms to the Ministry Decree n. 548 of 28 Aug.'95 published in the Official Gazette of the Italian Republic n. 301 of 28 Dec.'95"
PAL
n Only cassettes marked "VHS" can be used with this
videorecorder.
n HQ VHS is compatible with existing VHS equipment. n ShowView is a trademark applied for by Gemstar Develop-
ment Corporation. The ShowView system is manufactured under licence from Gemstar Development Corporation.
2. DO NOT block the recorder’s ventilation openings.
3. DO NOT place heavy objects on the recorder or remote control.
4. DO NOT place anything which might spill on top of the recorder or remote control.
5. AVOID violent shocks to the recorder during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form in the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the recorder turned on for a few hours to let the moisture dry.
ABOUT HEAD CLEANING
Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or inter­rupted. Be sure to contact your nearest JVC dealer if such troubles occur.
INSTALLING YOUR NEW RECORDER
It's essential that your video recorder be properly connected. Follow these steps carefully. THESE STEPS MUST BE COM-
Basic
PLETED BEFORE ANY VIDEO OPERATION CAN BE PER­FORMED.
EN 3
Connections
Back of TV
21-pin SCART
Aerial terminal
21-pin SCART Cable
Mains Power Cord
Mains outlet
connector
RF Cable (provided)
RF TEST switch
TV Aerial Cable
RF output channel adjustment screw
Rear View
CHECK CONTENTS
Make sure the package contains all of the accessories listed in “Specifications” (Z back cover).
1
SITUATE RECORDER
Place the recorder on a stable, horizontal surface.
2
CONNECT RECORDER TO TV
The connection method you use depends on the type of TV you have.
3
RF CONNECTION
To Connect To A TV With NO AV Input Terminals . . .
a– Disconnect the TV aerial cable from the TV. b– Connect the TV aerial cable to the ANT. IN jack
on the rear panel of the recorder.
c– Connect the provided RF cable between the RF
OUT jack on the rear panel of the recorder and the TV’s aerial terminal.
Before operating the recorder, make sure the TV’s channel is set to the VIDEO channel.
AV CONNECTION
To Connect To A TV With AV Input Terminals . . .
a– Connect the aerial, recorder and TV as per “RF
CONNECTION”.
b– Connect an optional SCART cable between the
AV1 IN/OUT socket on the rear panel of the recorder and the TV’s 21-pin SCART connector.
c– Set the RF TEST switch to OFF.
Before operating the recorder, make sure the TV is set to the VIDEO (or AV) mode.
CONNECT RECORDER TO MAINS
Plug the end of the mains power cord into a mains outlet.
4
Tune The TV To Your Video Recorder
The video recorder sends picture and sound signals via the RF connecting cable to your TV on UHF channel 36.
TURN ON THE RECORDER
Press OPERATE.
1
SELECT OUTPUT MODE
Set the RF TEST switch on the back of the recorder to ON.
2
CONTINUED ON NEXT PAGE.
4 EN
INSTALLING YOUR NEW RECORDER (cont.)
Connecting/
SET TV CHANNEL
Set your TV to the video channel (UHF channel 36). Two white bars appear on screen vertically.
3
Tune the TV until the bars are as clear as they can be.
Your TV should be set to the channel designated for
use with a video recorder, or to a spare channel if there is not a specified video channel on your TV.
RESET OUTPUT MODE
Return the RF TEST switch to OFF.
4
NOTES:
If CH36 is occupied by a local station, adjust the RF output channel adjustment screw to use another channel between CH32 and CH40 instead.
If some interference noise is continually seen on the screen, consult your JVC dealer.
The AV2 IN/DECODER connector can be used as an input terminal for an external decoder (descrambler). Simply connect a decoder and you can enjoy the variety of programming that is available through scrambled channels.
Using A Decoder
TV Receiver
RF Cable (provided)
AV2 IN/DECODER
AV2 SELECT switch
AV1 IN/OUT
TV Aerial Cable
Rear View
SELECT INPUT MODE
Set the AV2 SELECT switch to "DECODER".
1
CONNECT DECODER
Connect your recorder's AV2 IN/DECODER connector to the decoder's Euroconnector using a 21-pin SCART
2
cable.
SET TUNER
Follow the procedure starting on page 5.
3
NOTE:
When Connecting A Satellite Tuner . . .
. . . if you don't have a decoder connect the satellite tuner directly to the video recorder's AV2 IN/DECODER connector. . . . if you have a decoder, first connect the decoder to the decoder input of the satellite tuner, then connect the satellite tuner's output to the recorder's AV2 IN/DECODER connector. Refer to the instruction book for the satellite tuner and decoder. . . . set the AV2 SELECT switch to "AV2". . . . to view a programme via the satellite tuner, select AU 2 mode by pressing TV PROG. until "AU 2" appears on the display panel.
Satellite antenna
Satellite tuner
Decoder
INITIAL SETTINGS
CH SET
OPERATE
TV PROG.
PUSH JOGfi%
TV/VIDEO
Tuner Set
Turn on the TV and select the VIDEO channel (or AV mode).
EN 5
Your recorder needs to memorise all necessary stations in channel positions in order to record TV programmes. ATS+ (Auto Tuning System) automatically assigns all receivable stations in your area to call them up with the TV PROG. buttons without going through any vacant channels.
The following procedure describes how to select automatic channel setting.
TURN ON THE RECORDER
Press OPERATE.
1
+
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ACCESS LANGUAGE SCREEN
Press and hold CH SET for more than 2 seconds. The Language screen appears.
2
SELECT LANGUAGE
2
12 45
8
7
0
1
3
3 6 9
OPERATE
TV PROG+/–
OK
Press PUSH JOG%fi to place the pointer next to
3
the language of your choice, then press OK to enter your selection. The Ch. Set mode menu appears.
SELECT MODE
“AUTO CH SET” is the necessary mode for this
4
procedure, so simply press OK to enter the selection. The Country select screen appears.
SELECT COUNTRY
Press PUSH JOG%fi to place the pointer next to
5
your country's name, then press OK to initiate Auto Channel Set.
As the recorder searches for receivable stations, it displays broadcasts from the stations for a few seconds as it locates them.
ENGLISH DEUTSCH FRANCAIS ITALIANO CASTELLANO NEDERLANDS SVENSKA NORSK SUOMI DANSK
[5∞] =
AUTO CH SET
MANUAL CH SET
GUIDE PROG SET
[5∞] = [CANCEL] : EXIT
ÖSTERREICH NEDERLAND BELGIUM NORSK DEUTSCHLAND PORTUGAL DANMARK SUISSE ESPAÑA SUOMI GREECE SVERIGE ITALIA OTHERS
[5∞]
=
: AUTO CH SET
[CANCEL] : EXIT
AUTO CH SET
PLEASE WAIT
[CANCEL] : EXIT
CONTINUED ON NEXT PAGE.
6 EN
CH SET
INITIAL SETTINGS (cont.)
VIEW CONFIRMATION SCREEN
The stations your recorder
+
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
located appear on a
6
Confirmation screen — channel positions (PR), channels (CH) and station names (ID– Z pg. 33). To view the next page of the listing, press PUSH
JOG%fi . The blueback
%
%
screen and the program currently being broadcast by the highlighted station appear alternately for 5 seconds each.
The stations located in the selected country appear at the top of the list.
PR CH ID PR CH ID 01 25 ARD 08 C26 E-SP 02 C08 SKY1 09 55 WEST 03 10 ZDF 10 C24 SAT1 04 C65 RAI1 11 C23 OSF 05 C31 BBC1 12 C25 ESPN 06 C32 BBC2 13 C37 CNN 07 C33 3SAT 14 C35
5
5
]
[
5
=
: EDIT = [CANCEL] : DELETE [CH SET ] : EXIT
C: Cable
RETURN TO NORMAL
2
12 45
8
7
0
3 6 9
SCREEN
Press CH SET.
Depending on the reception conditions, the stations
7
may not be stored in order, and the station names may not be stored correctly.
Using the Confirmation screen, you can skip or add channel positions, enter station names and perform other operations. Refer to page 31 for the procedures.
For information on scrambled broadcasts, refer to page 31.
PUSH JOG
1
3
OK
NOTES:
Fine tuning is performed automatically when you select “AUTO CH SET”. If you want to perform it manually, refer to page 32.
To set the tuner manually, refer to “Storing Channels Manually” (Z pg. 31).
Clock Set
CLOCK
OPERATE
Turn on the TV and select the VIDEO channel (or AV mode).
+
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
EN 7
If you performed Auto Channel Set (Z pg. 5), the recorder’s built-in clock is also set automatically. The Auto and Manual clock setting procedures are necessary when . . .
– a power outage of more than 60 minutes occurs. – the tuner has been set manually. – the user desires to set the clock slightly ahead of the actual
time.
– the clock was not set even after Auto Tuner Set was
performed.
Whether you perform Auto or Manual clock setting, you can use the convenient Just Clock function.
Just Clock
The Just Clock function provides accurate time keeping through automatic adjustments at regular intervals, by reading data from
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
a PDC signal. The Just Clock option appears in the Clock Set and Auto Clock screens, and can be set “ON” or “OFF” (the default setting is “ON”). Press OK until the Just Clock setting begins blinking, then press PUSH JOG%fi to change the setting.
IMPORTANT: If you turn off Just Clock off, the accuracy of your recorder’s built-in clock may be reduced, which could adversely effect timer recording.
Both Auto and Manual clock setting procedures begin from step 3.
Preparation
PUSH JOG
2
12 45
8
7
0
1
3
3 6 9
TV/VIDEO
OPERATE
OK
TURN THE RECORDER ON
Press OPERATE.
1
ACCESS CLOCK SET SCREEN
Press CLOCK on the remote control. The Clock
2
Set screen appears.
TIME DATE YEAR 0: 00 01 . 01 00
JUST CLOCK: ON
TV PR. 1
5
[ ]: AUTO CLOCK [5∞] = [CLOCK] : EXIT
CONTINUED ON NEXT PAGE.
CLOCK SET
8 EN
CLOCK
INITIAL SETTINGS (cont.)
Auto Clock Set
+
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SET CLOCK AUTOMATICALLY
At the Clock Set screen, press PUSH JOG . The
3
Auto Clock screen appears and clock setting begins.
If "TV PR." isn't set to the channel position on
%
AUTO CLOCK
PLEASE WAIT
JUST CLOCK: ON TV PR. 1
which Auto Clock data is received, "ERROR" appears, and then the screen from step 2 reappears.
2
12 45
8
7
0
3 6 9
To set "TV PR.", press OK to place the pointer next to it, then cycle through the numbers by pressing PUSH JOG%fi until the number representing the channel position in which the station transmitting clock setting data is stored appears.
RETURN TO NORMAL SCREEN
Once clock setting is completed, press CLOCK to return to the normal screen.
4
1
3
OK
Manual Clock Set
PUSH JOG
NOTES:
Auto Clock and Just Clock require a PDC signal, and will not operate with a VPS signal.
Just Clock (when set to "ON") enables adjustment of the recorder's built-in clock every hour on the hour, except for 11 o'clock in the evening and midnight.
Just Clock is not effective when . . . – the recorder’s power is on (unless the recorder is tuned to
the same channel position selected in the Clock Set screen). – the recorder is in the Timer mode. – a difference of more than 3 minutes exists between the
built-in clock’s time and the actual time.
If Just Clock is set to "ON", the recorder’s clock is automati­cally adjusted at the start/end of Summer Time.
Auto clock setting and Just Clock may not function properly depending on the reception condition.
During Manual clock setting, if the day and month data are invalid (such as 31st April), the month digits are cleared automatically and the day digits begin blinking. Input the correct data.
If, in step 3 of the Manual clock setting procedure, the year digits are automatically cleared and the day digits begin blinking, it is possible that you have input 29th February for a non-leap year. Input the correct data.
SET DATE AND TIME
Press PUSH JOG%fi to set the hour, then press OK. The “minutes” display begins blinking. Repeat the proce-
3
dure to set the minutes, day, month and year.
SET JUST CLOCK
The default setting is “ON”. Set as desired by pressing
PUSH JOG%fi, then press OK.
4
If you set to “OFF”, you can disregard the next step as you won’t be able to receive regular clock adjust­ments.
SET CLOCK DATA SOURCE CHANNEL POSITION
The recorder is preset to receive clock setting and adjustment data from channel position 1. Press PUSH
5
JOG%fi to set the channel position to the number
representing the station transmitting clock setting data, then press OK.
START CLOCK OPERATION
Press CLOCK.
6
PLAYBACK
PLAY
STOP
SHUTTLE
PLAY
STOP/EJECT
Basic
EN 9
The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.
Playback
Turn on the TV and select the VIDEO channel (or AV mode).
+
2
12 45
7
8
3 6 9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
LOAD A CASSETTE
Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is
1
point toward the recorder. Don’t apply too much pressure when inserting.
The recorder power comes on automatically and the counter is reset to 0:00:00.
If the record safety tab has been removed, playback begins automatically.
FIND PROGRAMME START
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
0
0
POINT
If the tape is advanced past the start point, press REW or turn the SHUTTLE ring to the left and release it.
2
To go forward, press FF or turn the SHUTTLE ring to the right and release it.
START PLAYBACK
Press PLAY. “BEST” appears blinking in the recorder's display panel for 5 seconds. (Z pg. 16)
3
STOP PLAYBACK
Press STOP on the remote or STOP/EJECT on the recorder’s front panel. Then press STOP/EJECT to remove the cassette.
4
Usable cassettes
REW
1
3
FF
Compact VHS camcorder recordings can be played on this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.
This video recorder can record on regular VHS and Super VHS cassettes. However, it will record and play back regular VHS signals only. It is not possible to play back a recorded Super VHS tape.
10 EN
TV PROG.
SHUTTLE
PLAY
PLAY
JOG
REVIEW
PLAYBACK (cont.)
Take advantage of special functions possible with the recorder’s controls or the remote control.
Playback Features
+
REVIEW
12 45 7
SP/LP
REW
PAUSE
2
8 0
3 6 9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
TV PROG.
FF
PAUSE
NOTE:
Refer to the SHUTTLE ring illustration below as you read the following procedures.
Still
S
e
l
s
o
r
w
e
v
e
m
R
e
s
r
e
y
v
a
e
l
p
R
e
h
s
c
r
r
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
0
0
e
a
v
e
e
s
R
o
t
w
i
o
o
l
s
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
n
P
l
a
y
F
s
o
e
r
w
a
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
a
r
c
r
d
h
Still Picture/Frame-By-Frame Playback
PAUSE DURING PLAYBACK
Press PAUSE. If there is vertical jitter, use the TV PROG. buttons to correct the picture.
1
ACTIVATE FRAME-BY-FRAME PLAYBACK
Turn the JOG dial to the right for forward frame-by­frame playback, or to the left for reverse frame-by-frame
2
playback.
OR
Press PAUSE.
OR
Press PUSH JOG or .
To resume normal playback, press PLAY.
%
%
PUSH JOG
1
3
EN 11
Slow Motion
ACTIVATE SLOW-MOTION PLAYBACK
During playback or still, turn the SHUTTLE ring to the right for forward slow motion, or to the left for reverse
1
slow motion (refer to the illustration on the previous page).
OR
During still picture, press and hold PAUSE for 2 seconds, then release. Press and release again to return to still picture.
OR
During still picture, press and hold PUSH JOG or . Release to return to still picture.
To resume normal playback, press PLAY.
%
Variable-Speed Search
ACTIVATE VARIABLE-SPEED SEARCH
During playback or still, turn the SHUTTLE ring to the right for forward variable-speed search, or to the left for
1
reverse variable-speed search (refer to the illustration on the previous page).
OR
During playback, press PUSH JOG or .
The more times you press, the faster the playback picture moves.
To decrease speed, press the button for the opposite direction.
To resume normal playback, press PLAY.
%
%
High-Speed (Turbo) Search
ACTIVATE HIGH-SPEED SEARCH
During playback or still, turn the SHUTTLE ring all the way to the right for forward high-speed search, or to
1
the left for reverse high-speed search.
For forward search with a visible picture, turn the
SHUTTLE ring all the way to the right and release it within 1 second.
For reverse search with a visible picture, turn the
SHUTTLE ring all the way to the left and release it within 1 second.
OR
Press FF for forward high-speed search, or REW for reverse high-speed search.
For short searches, press and hold FF or REW for over
2 seconds. When released, normal playback resumes.
To resume normal playback, press PLAY.
Manual Tracking
Your video recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the TV PROG. buttons.
OVERRIDE AUTOMATIC TRACKING
Press SP/LP ( ) on the remote to engage manual
%
tracking.
1
ADJUST TRACKING MANUALLY
Press TV PROG. + or to adjust tracking.
2
RETURN TO AUTOMATIC TRACKING
Press SP/LP ( ) on the remote to re-engage auto­matic tracking.
3
NOTE:
When a new tape is inserted, the recorder enters the automatic tracking mode automatically.
Instant ReView
Simply by pressing a single button, the recorder power comes on, rewinds, and begins playback of the last timer-recorded programme. If you have several programmes recorded, you can easily access any of them.
NOTE:
Before starting, make sure that the recorder is off and that the Timer mode is disengaged.
ACTIVATE INSTANT REVIEW
Press REVIEW. The recorder power comes on and the recorder searches for the index code indicating the start
1
of the last timer-recorded programme. Once it’s found, playback begins automatically. The front display panel tells you how many programmes have been recorded. If you have, for example, 3 programmes, “REV 3” appears and blinks. To watch the first of the 3 programmes, press REVIEW three times. The recorder searches and begins playback automatically. You can access a programme as far as 9 index codes away from the current tape position.
NOTE:
Instant ReView is not possible while the recorder is in the Timer mode.
12 EN
PLAY
C. MEMORY
REW
SHUTTLE
PLAYBACK (cont.)
Repeat Playback
Your video recorder can automatically play back the whole tape 20 times repeatedly.
+
SCENE FINDER
STOP
2
12 45
8
7
0
1
3
3 6 9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
OPERATE
FF
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
0
0
START PLAYBACK
Press PLAY.
1
ACTIVATE REPEAT PLAYBACK
Press PLAY and hold for over 5 seconds, then release.
The Play indicator ( ) on the display panel blinks
2
slowly.
The tape plays 20 times automatically, and then stops.
STOP PLAYBACK
Press STOP at any time to stop playback.
3
NOTE:
Pressing PLAY, REW , FF or PAUSE also stops Repeat Playback.
NTSC Playback
Your video recorder is equipped with NTSC circuitry that can play back NTSC tapes.
PUSH JOG
LOAD A CASSETTE
Insert a cassette recorded in NTSC.
1
START PLAYBACK
Press PLAY. “NT” appears on the display panel.
Some TVs shrink the picture vertically and place
2
black bars at the top and bottom of the screen. This is not a malfunction on the part of either the video recorder or the TV.
The picture may roll up and down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.)
The counter and tape remaining time readings will be incorrect.
During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour.
Depending on the type of TV, the top and bottom portions of superimposed displays may be cut off during NTSC playback.
EN 13
Scene Finder
This function helps you check contents of unlabeled recorded tapes at the touch of a single button.
Search Search Search
FF REW FF REW FF REW
5 seconds 5 seconds
on counter
5 seconds10 minutes
10 minutes on counter
NOTE:
Scene Finder cannot be used when the recorder is in the Record mode.
ACTIVATE SCENE FINDER
Press SCENE FINDER. The recorder starts forward high- speed search for 5 seconds and then fast-forwards 10
1
minutes on the counter. This cycle is repeated until the end of the tape is reached.
To start Scene Finder in the reverse direction, press
SCENE FINDER and then turn the SHUTTLE ring to the left (or press the remote’s REW button) within 2 seconds. This cycle is repeated until the beginning of the tape.
During Scene Finder, the following indications appear on the display panel:
STOP SCENE FINDER
Press STOP.
2
Index Search
Your recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction.
NOTE:
Before starting, make sure the recorder is in the Stop mode.
ACTIVATE INDEX SEARCH
Press PUSH JOG or ( or £). “ 1” or “£ 1” is displayed on screen and search begins in
1
the corresponding direction.
To access index codes 2 through 9, press PUSH JOG
%
or repeatedly until the correct index number is
%
displayed.
Ex.: To locate the beginning of B from the current
position, press PUSH JOG twice. To locate the beginning of D from the current position, press PUSH JOG once.
When the specified index code is located, playback begins automatically.
%
%
%
%
Current position
AB C D E F
–2 –1 1 2 3
%
%
£ 2
Index number
NOTES:
During Scene Finder high-speed search, you can also hear the tape sound. During fast forward or rewind, you hear the current TV sound instead.
Scene Finder does not function during Index Search.
Tape Position Indicator
The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of “5” in relation to “0” (beginning) or “+” (end) shows you where you are on the tape.
”O.S.D.” (Z pg. 18) must be set to “ON”, or the indicator will not appear.
0
NOTE:
Depending on the type of tape used, there may be times when the indication is not correct.
3
1:23:45
REMAIN 2:35
Next Function Memory
You can set your recorder's power to go off automatically after the tape is fully rewound. Before starting, make sure the recorder is in the Stop mode. For Automatic Power Off After Tape Rewind . . . . . . press REW, then press OPERATE within 2 seconds.
NOTE:
If you want the power to be turned off automatically when the counter reads “0:00:00” (instead of at the beginning of the tape), press C.MEMORY so that the “M” mark appears before pressing REW.
+++
Information On Colour System
You can also record SECAM signals, or play back a MESECAM tape on this recorder. When a MESECAM tape is played back, "MES" appears on the display panel. MESECAM is the designa­tion for tapes with SECAM signals that have been recorded on a MESECAM-compatible PAL video recorder.
14 EN
PLAYBACK (cont.)
Tape Remaining Time
DISPLAY REMAINING TIME
Press DISPLAY until the time remaining on the tape appears.
1
By pressing the DISPLAY button, you can change the
display to show the counter reading, tape remaining time, or clock time.
NOTE:
Depending on the type of tape used, there may be times when the tape remaining time reading may not appear right away, or is not correct. "- - : - -" may sometimes appear, or the display may blink on occasion.
Counter Memory
Returns to the counter reading of “0:00:00” to conveniently find a specific place on the tape automatically.
SET COUNTER MEMORY
Press C. RESET during playback at a point you wish to locate later. The counter reads “0:00:00”. Then press C.
1
MEMORY, and “M” appears in front of the counter digits.
ACTIVATE COUNTER MEMORY
When you wish to return to the designated point, press
STOP and then REW or FF.
2
The tape rewinds or fast-forwards and stops at about 0:00:00 automatically.
To cancel Counter Memory, press C.MEMORY again.
Remote A/B Code Switching
The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control’s A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals. You can easily modify your video recorder to respond to B code signals.
REMOVE POWER SUPPLY
Unplug the mains power cord from the mains outlet.
1
SET A/B CODE SWITCH
Set to B.
2
RE-SUPPLY POWER
Plug the mains power cord back into the mains outlet.
3
TURN THE RECORDER ON
Press OPERATE on the remote control. The recorder will now only respond to B code signals.
4
NOTE:
Some TV sets may malfunction in response to the B mode. If this happens, switch back to the A mode.
RECORDING
STOP
TV/VIDEO
TV PROG.
PAUSE
PLAY
STOP/EJECT
SP/LP
TV PROG.
Basic Recording
+
RECORD
EN 15
TV signals being received by the recorder’s built-in tuner can be recorded onto a video tape. You can “capture” a TV programme using your video recorder.
LOAD A CASSETTE
Insert a cassette with the record safety tab intact.
The counter is reset to 0:00:00 and the recorder
1
power comes on automatically.
If your recorder is connected to the TV via AV connec-
tion, press TV/VIDEO to select the VIDEO mode.
CHOOSE A PROGRAMME
Press TV PROG. +/– or the NUMBER keys to select the channel you wish to record. The name of the station
2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
appears in the recorder’s display panel for 5 seconds, followed by the channel position number. (Only stations that appear in the Confirmation screen will be displayed.)
The TV PROG. dial can also be used to select a channel.
SET TAPE SPEED (E439EG ONLY)
Press SP/LP. Check the SP/LP indicator on the recorder display panel to confirm the selected tape speed.
3
NUMBER
SP/LP
RECORD
2
12 45
8
7
0
1
3
3 6 9
PLAY
TV PROG.
PAUSE
START RECORDING
Press and hold RECORD and PLAY on the remote control, or press RECORD on the recorder.
4
B.E.S.T. takes place at the beginning of both the first SP and the first LP (E439EG only) recording after inserting the cassette (Z pg. 16).
PAUSE/RESUME RECORDING
Press PAUSE. Press PLAY to resume recording.
5
STOP RECORDING
Press STOP on the remote control or STOP/EJECT on the recorder. Then press STOP/EJECT to remove the
6
cassette.
Accidental erasure prevention
To prevent accidental recording on a recorded cassette, remove its safety tab. To record on it later, cover the hole with adhesive tape.
Record safety tab
16 EN
PLAY
RECORD
B.E.S.T. Picture
RECORDING (cont.)
The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. The default setting for both recording and playback is “ON”.
System
Turn on the TV and select the VIDEO channel (or AV mode).
+
RECORD
2
12 45
8
7
0
3 6 9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
MODE
Recording
LOAD A CASSETTE
Insert a cassette with the record safety tab intact.
The recorder power comes on automatically.
1
ACCESS MODE SELECT
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
0
0
SCREEN
Press MODE. The O.S.D./ B.E.S.T. screen appears.
2
O.S.D. : ON
B.E.S.T. : ON
5
[5∞] = [ ]: ON/OFF [MODE] : EXIT
CONFIRM B.E.S.T. STATUS
The default setting is “ON”. If this is the case, go to step
4. If not, press PUSH JOGfi to place the pointer next to
3
“B.E.S.T.”, then press PUSH JOG to set to “ON”.
%
CLOSE MODE SELECT SCREEN
Press MODE.
4
START RECORDING
Press and hold RECORD and PLAY on the remote, or press RECORD on the recorder.
5
The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording.
When the "BEST" indicator begins blinking, that means adjustment is complete.
PUSH JOG
1
3
Display Panel Indication
As the tape check progresses, the “– –” marks on the display panel increase upward. Once the "BEST" indicator starts blinking, the check is complete.
+
PAUSE
RECORD
PLAY
PLAY
RECORD
2
12 45
8
7
0
1
3
3 6 9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
PAUSE
EN 17
NOTES:
The B.E.S.T. system works for both SP and LP (E439EG only) modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.
In the case of timer recording, the B.E.S.T. system works
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
0
0
before recording is initiated.
Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re­performed.
ATTENTION:
Since the B.E.S.T. system works before recording actually starts, there is a delay of approximately 7 seconds after RECORD and PLAY on the remote are pressed, or RECORD on the recorder is pressed. To make sure you record the desired scene or programme in its entirety, first perform the following steps:
1) Press and hold PAUSE and RECORD to engage the
RECORD PAUSE mode.
The recorder then automatically checks the condition of the tape and, after approximately 7 seconds, re­enters RECORD PAUSE.
2) Press PLAY to start recording.
If you want to bypass the B.E.S.T. system and begin recording immediately, set “B.E.S.T.” to “OFF” in step 3 on page 16.
Playback
The recorder assesses the quality of the tape once you initiate playback.
When watching a tape recorded with “B.E.S.T.” set to “ON”, it is recommended that you leave B.E.S.T. on during playback as well.
START PLAYBACK
Press PLAY.
1
The recorder adjusts the playback picture quality based on the quality of the tape in use.
B.E.S.T. is active during Auto Tracking. “BEST” appears blinking on the recorder’s display panel.
NOTES:
When watching a rental tape, or one recorded on another video recorder, set B.E.S.T. to your preference by performing steps 2 through 4 on page 16.
"BEST" only appears at the beginning of automatic tracking. Even though it doesn't appear after that, the B.E.S.T. function is operative.
18 EN
OPERATE
OPERATE
On-Screen
RECORDING (cont.)
You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF. Messages appear in the language you selected during Auto Channel Set (Z pg. 5).
Displays
Turn on the TV and select the VIDEO channel (or AV mode).
+
2
12 45 7
8 0
3 6 9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
MODE
TURN ON THE RECORDER
Press OPERATE.
1
ACCESS MODE SELECT SCREEN
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
0
0
Press MODE. The O.S.D./ B.E.S.T. screen appears.
2
O.S.D. : ON
B.E.S.T. : ON
5
[5∞] = [ ]: ON/OFF [MODE] : EXIT
SELECT MODE
The pointer should already be next to “O.S.D.”. If not, press PUSH JOG%fi to place it there.
3
ENABLE/DISABLE ON-SCREEN DISPLAY
The default setting is “ON”, so if you want on-screen displays, leave the setting as is and go to step 5. If you
4
don’t want the displays to appear, press PUSH JOG to set “O.S.D.” to “OFF”.
%
CLOSE MODE SELECT SCREEN
Press MODE.
1
3
PUSH JOG
The superimposed indication on the TV screen tells you what the recorder is doing.
11
2 5
6
8
PR. 12 ABCD ] SP
23 : 59
31. 12. 96 – WARNING– TIMER RECORDING TO START SOON [CANCEL]
++
0
1
q6
+
M –9 : 59 : 59
REMAIN 9 : 59
+
4 3
7 9
10
5
1– Operation mode indicators 2– Channel position number and station name/Aux. indicator
(AUX1, AUX2 or F-AUX)
3– Cassette loaded mark 4– Tape speed SP/LP/EP (EP is for NTSC playback only)
[E439EG only]
5– Clock display 6– Current day/month/year 7– Tape direction 8– Tape position indicator (Z pg. 13) 9– Counter display (including Counter Memory indicator) 10– Tape remaining time indicator 11– Timer warning display
DISPLAY
TV/VIDEO
TV PROG.
RECORD
Recording Features
+
EN 19
Record One Programme While Watching Another
If your recorder is connected to the TV via AV connection, . . .
. . . press TV/VIDEO. The recorder's VIDEO indicator and the TV broadcast being recorded disappear.
SELECT CHANNEL TO WATCH
Once recording is in progress, all you need to do is to set the channel controls on the TV for the station you
1
wish to view.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
The programme selected with the TV’s channel controls appears on the TV screen while the one selected with the TV PROG. button is recorded on the tape.
If a decoder is connected to the recorder (Z pg. 4), you can select a scrambled channel as well with the TV channel controls.
Elapsed Recording Time Indication
You can check the exact time of a recording.
C.RESET
2
12 45
8
7
0
1
3
3 6 9
TV PROG.
SET COUNTER DISPLAY
Press DISPLAY until a counter reading appears on the dispay panel.
1
RESET COUNTER
Press C. RESET before starting recording or playback.
The counter is reset to “0:00:00” and shows the exact
2
elapsed time as the tape runs.
Instant Timer Recording (ITR)
This easy method lets you record for from 30 minutes to 6 hours (selectable in 30-min. increments), and shuts the recorder off after recording is finished.
START RECORDING
Press RECORD on the recorder.
1
ENGAGE ITR MODE
Press RECORD again. ITR blinks and 0:30 appears on the front display panel.
2
SET RECORDING DURATION
If you want to record for more than 30 minutes, press
RECORD to extend the time. Each press extends
3
recording time by 30 minutes.
NOTE:
You can only perform ITR using the RECORD button on the recorder's front panel.
20 EN
CH SET
Information On ShowView
TIMER RECORDING
With ShowView, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise.
NOTE:
“Guide Prog. Number” (GUIDE PROG) refers to the assigned TV station numbers, according to broadcast area, for ShowView timer recording.
Turn on the TV and select the VIDEO channel (or AV mode).
NUMBER
CANCEL
+
2
12 45 7
8
3 6 9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
IMPORTANT
Perform the following procedure after the channel setting steps on pages 5 and 31 – 32, and after the Clock Set procedure on page 7. After setting the Guide Prog. Numbers, the station names and channel positions may be incorrect if you stored or skipped channels. In this case, re-perform Guide Prog. Number setting.
Guide Prog. Number Set
MAKE LIST OF STORED STATION NAMES AND CHANNEL POSITIONS
(Ex.)
Channel position Station name
1
1 ARD 2 ZDF 3 WDR
PUSH JOG
1
3
OK
ACCESS CH. SET MODE MENU SCREEN
Press and hold CH SET for over 2 seconds. The Language screen appears. Press OK to access the Ch.
2
Set Mode Menu screen.
SELECT MODE
Press PUSH JOG%fi to place the pointer next to
3
“GUIDE PROG SET”, then press OK. The Guide Prog. Set screen appears.
[5∞] = [CANCEL] : EXIT
AUTO CH SET
MANUAL CH SET
GUIDE PROG SET
EN 21
ENTER SHOWVIEW NUMBER
Press OK, and a cursor appears above “GUIDE
4
PROG”. Then, using the NUMBER keys, input the ShowView number (found in most TV listings) of a program scheduled to be broadcast on each station on the list from step 1, starting at the top. If you enter the wrong number, press CANCEL and input the correct number.
12345
5
GUIDE PROG TV PROG
11
[0 – 9] =
When entering a ShowView number for ARD
ENTER CHANNEL POSITION NUMBER
Press OK and the display
4
under “TV PROG” begins
5
blinking.
If the blinking number under “TV PROG” agrees with the channel position . . .
. . . press OK.
If the numbers do not agree . . .
. . . input the channel position using PUSH JOG%fi or the NUMBER keys, then press OK.
If you input the ShowView number of a program that has already aired, “ERROR” appears on screen for a few seconds. Input the correct ShowView number.
Repeat steps 4 and 5 as necessary.
GUIDE PROG TV PROG 250 39
[5∞] =
CLOSE MENU
Press CH SET and selection is complete.
6
If you already know the Guide Prog. number for a station . . . 1– After step 3, press PUSH JOG .
The GUIDE PROG number begins blinking.
2– Enter the Guide Prog. number using the NUMBER keys or
PUSH JOG
The TV PROG number begins blinking.
3– Enter the channel position using the NUMBER keys or
PUSH JOG
Repeat 2 and 3 as necessary.
4– Press CH SET.
%
, then press PUSH JOG .
%
, then press PUSH JOG .
%
%
%
When Using A Satellite Tuner
Satellite Antenna
Ex. 1
Satellite Tuner
AV2 IN/DECODER
AV2 SELECT Switch
TV Receiver
Preparation 1– Connect the satellite tuner to the AV2 IN/DECODER
connector on the rear of your recorder.
2– Set the AV2 SELECT switch to "AV2". To Record Satellite Broadcasts . . .
1– Select the appropriate channel on the satellite tuner. 2– Press NUMBER key "0" to set your recorder's input mode to
"AUX2".
3– Start recording ( To Record Satellite Broadcasts Using ShowView Timer
Recording . . . 1– Perform Guide Prog. Number setting.
In step 5 in the left column, press NUMBER key "0" to set
"TV PROG" to "AUX2".
2– Perform ShowView Timer Recording ( To Record Satellite Broadcasts Using Regular Timer Recording . . .
1– In step 6 on page 25, press TV PROG. +/– to set the channel
position to "AUX2".
Ex. 2
Satellite Tuner and Decoder
Z pg. 15, steps 3 – 6).
Aerial or Cable
Z pg. 22).
NOTES:
When timer-recording a satellite programme, first set the satellite tuner to the appropriate channel before the selected programme begins and then set the satellite tuner's timer. If your satellite tuner does not have a timer, leave it switched on.
If your recorder's front panel VIDEO and/or AUDIO connec­tors are being used, they take priority and "AUX2" cannot be selected. Make sure no cables are connected to the front panel connectors when performing this procedure.
22 EN
STOP+/–
DATE+/–
ShowView Timer
TIMER RECORDING(cont.)
During ShowView and regular timer programming, the Illumi­Guide feature tells you which button on the remote control must be pressed next by lighting it up. To use this feature, press
ILLUMI GUIDE before performing step 1. (PROG, REW, PLAY, FF light up at this time.)
If you aren't going to use the Illumi-Guide feature, go directly to step 1.
Recording
Before performing ShowView timer recording:
Be sure to read "Information On ShowView" (Z pg. 20).
Insert a cassette with the safety tab in place. The recorder
will come on automatically.
Turn on the TV and select the VIDEO channel (or AV mode).
NUMBER
CANCEL
START+/–
+
2
12 45 7
8
3 6 9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
TV PROG+/–
ACCESS TIMER PROGRAM­MING SCREEN
Press PROG.
TIMER PROGRAMMING
1
[0 – 9] : SHOWVIEW [+/-] : EXPRESS PROGRAMING [CANCEL] : EXIT
The front display panel looks like this:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
0
0
If you are using the Illumi-Guide feature, the following
buttons will light up: NUMBER keys (0–9), START +/–, STOP +/–, DATE +/–, TV PROG +/–, and CANCEL.
ENTER SHOWVIEW NUMBER
Press the NUMBER keys to enter the ShowView
2
number of a programme you wish to record.
If you make a mistake,
press CANCEL and then input the correct number.
The ShowView number you enter appears on the front display panel:
SHOWVIEW
1 2 3 4 5 6 7 8 5
[0 – 9] =
PROG.
1
3
OK
ILLUMI GUIDE
When Using The Illumi-Guide Feature
Buttons light or blink on the remote control for approximately 10 seconds. If the button or buttons extinguish during timer programming, press ILLUMI GUIDE and the button or buttons previously lit or blinking come back on. If the button or buttons do not re-light or start blinking again, press CANCEL and re-perform the timer programming procedure from the beginning.
If for some reason the remote control's signal is not received by the video recorder, press CANCEL and re-perform the timer programming procedure from the beginning.
If you are using the Illumi-Guide feature, OK blinks when the following buttons are lit: NUMBER keys (0–
9) and CANCEL.
+
ADD TIME
TIMER
SP/LP
DAILY
: PDC
TIMER
CANCEL
2
12 45
8
7
0
3 6 9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
WEEKLY
EN 23
ACCESS SHOWVIEW PROGRAM SCREEN
Press OK, and the
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ShowView Program screen
3
appears (if you’re just starting out, “P1” appears).
SHOWVIEW 12345678
If the number you entered is invalid, “ERROR” appears. Press CANCEL and input a valid ShowView number.
The front display panel looks like this:
SP
If you are using the Illumi-Guide feature, OK blinks.
If you’re not receiving PDC/VPS, press NUMBER key
“7” to set to "OFF" (Z pg. 26).
– P1 –
START STOP 21: 00 = 22 : 00
SP DATE TV PROG
25. 12 1
:OK
ON
ARD
SET TAPE SPEED (E439EG ONLY)
Press SP/LP to set the tape speed.
4
SP/LP
1
3
OK
RETURN TO NORMAL SCREEN
Press OK.
Repeat steps 1–5 for each additional programme.
5
ENGAGE RECORDER’S TIMER MODE
Press TIMER.
6
NOTE:
For safety, your recorder disables all other functions while in the Timer mode. If you want to use the recorder but its Timer mode is engaged, press TIMER and all other functions are operable. To re-engage the timer, press TIMER.
To Delay The Stop Time . . .
. . . press ADD TIME (NUMBER Key "5") after pressing OK in step 3. Each time you press, the Stop time is delayed by 5 minutes (meaning that 5 minutes of recording time is added). You can easily compensate for anticipated programme schedule delays this way.
To Timer-Record Weekly Or Daily Serials . . .
. . . after pressing OK in step 3, press WEEKLY (NUMBER key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily serials (Monday–Friday).
You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (Z pg. 26).
24 EN
DATE+/–
STOP+/–
Regular Timer Programming
Remember, the clock must be set before you can progamme the timer (Z pg. 7).
Before performing the following steps:
Insert a cassette with the safety tab in place. The recorder will come on automatically.
Turn on the TV and select the VIDEO channel (or AV mode).
+
CANCEL
START+/–
2
12 45
8
7
0
3 6 9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
TV PROG+/–
TIMER RECORDING(cont.)
If you don’t know the SowView number for the programme you wish to record, use the following procedure to set your recorder to timer-record the programme. Or you can use the Illumi-Guide feature, where the remote control tells you which button to press next by lighting it up. To use the Illumi-Guide feature, press ILLUMI GUIDE before performing step 1. (PROG, REW, PLAY, FF light up at this time.)
If you aren't going to use the Illumi-Guide feature, go directly to step 1.
ACCESS TIMER PROGRAM­MING SCREEN
Press PROG.
If you are using the Illumi-Guide feature, the following
1
buttons will light up: NUMBER keys (0–9), START +/–, STOP +/–, DATE +/–, TV PROG +/–, and CANCEL.
ACCESS PROGRAMME
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
0
0
SCREEN
Press START +/–. (If you’re just starting out, “P1”
2
appears.)
The front display panel looks like this:
SP
If you are using the Illumi-Guide feature, the following
buttons will light up: START +/–, STOP +/–, DATE +/–, and TV PROG +/–.
START STOP – : – – = – : – –
SP DATE TV PROG
25. 12 – –
[+/–] =
– P1 –
ON
PROG.
1
3
ILLUMI GUIDE
When Using The Illumi-Guide Feature
Buttons light or blink on the remote control for approximately 10 seconds. If the button or buttons extinguish during timer programming, press ILLUMI GUIDE and the button or buttons previously lit or blinking come back on. If the button or buttons do not re-light or start blinking again, press CANCEL and re-perform the timer programming procedure from the beginning.
If for some reason the remote control's signal is not received by the video recorder, press CANCEL and re-perform the timer programming procedure from the beginning.
ENTER PROGRAMME START TIME
Press START +/– to enter the time you want
3
recording to start.
Press and hold START +/– to move in 30-
minute increments, or press and release repeatedly to move 1 minute at a time.
The front display panel looks like this:
SP
If you are using the Illumi-Guide feature, the following buttons remain lit: START +/–, STOP +/–, DATE +/–, and TV PROG +/–.
START STOP 21 : 00 = – : – –
SP DATE TV PROG
25. 12 – –
[+/–] =
– P1 –
ON
+
SP/LP
DAILY
WEEKLY
STOP+/–
DATE+/–
: PDC
START+/–
2
12 45
8
7
0
3 6 9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
TIMER
TV PROG+/–
EN 25
ENTER PROGRAMME STOP TIME
Press STOP +/– to enter the time you want recording to
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
0
0
stop.
4
If you are using the Illumi-Guide feature, the following buttons remain lit: START +/–, STOP +/–, DATE +/–, and TV PROG +/–.
ENTER PROGRAMME DATE
Press DATE +/–. (The current date appears on screen. The date you enter appears in its place.)
5
If you are using the Illumi-Guide feature, the following buttons remain lit: START +/–, STOP +/–, DATE +/–, and TV PROG +/–.
ENTER CHANNEL POSITION
Press TV PROG. +/–.
If you’re not receiving
6
PDC/VPS, press NUMBER key “7” to set "OFF" (Z pg. 26).
to
[+/ –] =
– P1 –
START STOP 21: 00 = 22 : 00
SP DATE TV PROG
25. 12 1
ON
ARD
1
3
OK
NOTES:
For safety, your recorder disables all other functions while in the Timer mode. If you want to use the recorder but its Timer mode is engaged, press TIMER and all other functions are operable. To re-engage the timer, press TIMER.
To timer-record from a satellite tuner connected to your recorder's AV2 IN/DECODER connector, press TV PROG. +/– in step 6 above to set the channel position to "AUX2".
You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (Z pg. 26).
SP
D
M
If you are using the Illumi-Guide feature, OK blinks when the following buttons are lit: START +/–, STOP +/–, DATE +/–, and TV PROG +/–.
SET TAPE SPEED (E439EG ONLY)
Press SP/LP to set the tape speed.
7
RETURN TO NORMAL SCREEN
After confirming all information is correct, press OK and the normal screen appears.
8
Repeat steps 1–8 for each additional programme.
ENGAGE RECORDER’S TIMER MODE
Press TIMER.
9
To Timer-Record Weekly Or Daily Serials . . .
. . . anytime during steps 2 through 8, press WEEKLY (NUMBER key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily serials (Monday–Friday).
26 EN
TIMER RECORDING (cont.)
Check And Cancel Programmes
ACCESS PROGRAMME SCREEN
Press PROG CHECK. Each time you press the next program’s information appears.
1
Press OK and watch the front display panel as the
Start and Stop times, the Date and the Channel Position appear.
If the recorder is turned on and the TV is set to its VIDEO mode, you can check program information on screen as well.
If All Information Is Correct . . .
. . . programming is completed.
If You Wish To Revise Data . . .
. . . with the recorder's power turned on, go to step 2.
If You Wish To Cancel A Program . . .
. . . . with the recorder's power turned on, press
CANCEL. All information you input is deleted.
REVISE PROGRAMME IN­FORMATION
Input the appropriate data using the START +/–, STOP +/–, DATE +/– and TV PROG. +/– buttons on the
2
remote control.
Timer Warning
If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on screen to tell you that the record­ing is to start in 5 minutes.
NOTES:
The warning only appears if you’re not in the Timer mode at that time.
If this recorder is being used as the player for tape dubbing, the warning screen is recorded on the tape in the other video recorder.
The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press CANCEL.
– WARNING– TIMER RECORDING TO START SOON
[CANCEL]
Auto SP/LP Timer (E439EG only)
If, when recording in SP mode, there is not enough tape to record the entire programme, the recorder automatically switches to LP mode to allow complete recording.
ENGAGE AUTO SP/LP TIMER
Press AUTO SP/LP TIMER on the recorder front panel. The button lights “green”.
1
For Example . . .
Recording a program of 210 minutes in length onto a 180-minute tape
Approximately 150 minutes Approximately 60 minutes
SP mode
Total 210 minutes
Make sure you press AUTO SP/LP TIMER before performing timer programming.
NOTES:
The Auto SP/LP Timer feature is not available during ITR (Instant Timer Recording), and the feature will not work properly with any tapes longer than E-180 as well as some tapes of shorter lenghs.
Even if, in step 1, you press AUTO SP/LP TIMER and it lights “green”, that doesn’t mean that the recorder will automati­cally change from SP to LP mode during the course of the recording. Watch the tape later to confirm.
If you have programmed the recorder to timer-record 2 or more programs, the second programme and those thereafter may not fit on the tape if you engage the Auto SP/LP Timer mode. In this case, make sure the mode is not engaged, then set the tape speed manually during timer programming.
There may be some noise at the point on the tape where the recorder switches from SP to LP mode.
If you perform timer recording with both PDC/VPS and the Auto SP/LP Timer activated, and the programme goes beyond its originally scheduled length, there may be times when the programme cannot be recorded in its entirety.
PDC/VPS Recording
Now available from some TV stations, PDC (Programme Delivery Control) and VPS (Video Programme System) are service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over advertised times you preset in the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed.
To Use PDC/VPS Service . . .
The default setting for PDC/VPS is "ON". To cancel PDC/VPS, press NUMBER key "7" so that "OFF" is displayed on screen during ShowView or regular timer programming.
LP mode
NOTES:
When you manually enter programmes (regular timer programming), set the start time (PDC or VPS time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.
PDC/VPS recording is also possible when a satellite tuner or a cable system is connected to AV2 IN on your recorder.
EDITING
AUDIO MONITOR
PLAY
PAUSE
AUDIO DUBBING
EN 27
Audio dubbing replaces the audio sound of a previously recorded tape with a new soundtrack.
Audio Dubbing [E439EG only]
+
CD Player
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
MAKE CONNECTIONS
Connect an audio component to the AUDIO IN connector on the recorder's front panel.
1
SET INPUT MODE
Press NUMBER key "0". "F-AU" appears in place of a channel number.
2
LOCATE START POINT
Press PLAY to start playback of the tape in your recorder, and press PAUSE when you find the point
3
where you want to start dubbing.
ENGAGE AUDIO DUBBING
Press AUDIO DUBBING.
4
START DUBBING
Engage the audio component's Play mode, then press
PLAY to start the tape in your recorder. Audio dubbing
5
begins at this point.
To stop dubbing temporarily, press PAUSE. Press PLAY to resume dubbing.
NUMBER "0"
2
12 45
8
7
0
1
3
3 6 9
PLAY
PAUSE
END AUDIO DUBBING
Press STOP to stop the tape in your recorder, and engage the audio component's Stop mode.
6
NOTES:
Audio dubbing stops automatically when the counter reaches "0:00:00", and the recorder enters the Play mode. Check the counter reading before dubbing.
Audio dubbing is also possible using the rear panel AV1 IN/ OUT or AV2 IN connector. When using these connectors, make sure to select the correct input mode in step 2.
Connections made to the recorder's front panel are given priority over those made to the rear panel connectors.
Audio dubbing cannot be performed on a cassette that has had its record safety tab removed.
28 EN
EDITING (cont.)
You can use your video recorder as the source player or the recording deck.
Edit To Or From Another Video Recorder
2
12 45
7
NUMBER "0"
8 0
3 6 9
TV PROG.
MAKE CONNECTIONS
Connect the player’s AUDIO/VIDEO OUT connector to the recorder’s AUDIO/VIDEO IN connector.
1
When Using Your Video Recorder As The Source Player . . .
. . . connect its AV1 IN/OUT connector to the recording deck.
When Using Your Video Recorder As The Recording Deck . . .
. . . . you can use the AV1 IN/OUT or AV2 IN connectors.
SET RECORDING DECK’S INPUT MODE
Set to AUX. With this video recorder, press NUMBER Key "0" or TV PROG. to select depending on the
2
connector being used — “AU 1” for the AV1 IN/OUT connector, or “AU 2” for the AV2 IN connector.
When using the AV2 IN connector, make sure the AV2 SELECT switch is set to "AV2".
START SOURCE PLAYER
Engage its Play mode.
3
START RECORDING DECK
Engage its Record mode.
TV Receiver
VIDEO CHANNEL
RF Cable (provided)
1
Player Your recorder
AV2 SELECT switch
3
21-pin SCART Cable (not provided)
Another recorder
Recorder
4
NOTE:
All necessary cables can be obtained from your dealer.
Recorder
AV2 SELECT switch
21-pin SCART Cable (not provided)
Another recorder
Player
Your recorder
RF Cable (provided)
TV Receiver
VIDEO CHAN­NEL
EN 29
You can use a camcorder as the source player and your video recorder as the recorder.
Edit From A Camcorder
2
12 45 7
NUMBER "0"
1
8 0
3
3 6 9
MAKE CONNECTIONS
Connect the camcorder’s AUDIO/VIDEO OUT connectors to the recorder’s front panel AUDIO/VIDEO
1
input connectors.
When a Master Edit Control-equipped JVC camcorder is used, the camcorder is capable of controlling the recorder. Refer to the camcorder’s instruction manual for operating procedure. (E439EG only)
SET RECORDER’S INPUT MODE
Press NUMBER key “0”. “F-AU” appears in place of a channel number.
2
START CAMCORDER
Engage its Play mode.
3
START RECORDER
Engage its Record mode.
4
NOTE:
Connections made to the front panel AUDIO/VIDEO input connectors automatically override those made to the rear panel AUDIO/VIDEO input connectors.
VIDEO IN
Camcorder
Recorder
+
Audio/Video Cable (not provided)
Player
AUDIO IN
VIDEO OUT
AUDIO OUT
EDIT
Your recorder
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
To the rear panel PAUSE connector [E439EG only]
Editing Cable (not provided)
30 EN
TV/VIDEO
STOP
DISPLAY
MUTE
TV/VCR
Multi-Brand Remote Con­trol
OPERATE
2
NUMBER
12 45 7
8 0
3 6 9
TV PROG.
REMOTE CONTROL
Your remote control can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer’s TVs can also be controlled by setting the appropriate switch on the remote control.
Before you start . . .
Turn on the TV using its remote control.
Set the remote control’s TV/VCR switch to TV.
NOTE:
If your TV is a JVC, you don’t have to set the code in step 1. Go to step 2.
SET TV BRAND CODE
Refer to the chart below. While holding down OPER­ATE, enter your TV’s brand code using the NUMBER
1
keys, then press STOP.
You don’t have to repeat this step until you replace your remote control’s batteries.
TRY OPERATING TV
Press OPERATE on the remote to turn the TV off. If it goes off, try other operations.
2
The OPERATE button, TV/VIDEO button, TV PROG. +/– button, TV VOL. %fi button and MUTE button on
the remote can all be used to operate the TV.
To return the remote to video recorder control, set its TV/VCR switch to VCR.
DIGIT ENTRY
1
TV VOL. %fi
CODE TV BRAND NAME
01 JVC 02 BRANDT, NORDMENDE, SABA, TELEAVIA,
TELEFUNKEN, THOMSON 03 FERGUSON 04 PHILIPS 05 BLAUPUNKT, GRUNDIG 06 SONY 07 PANASONIC 08 GRAETZ, ITT, LUXOR, SALORA, SELECO 09 MIVAR 10 HITACHI 11 TOSHIBA 12 MITSUBISHI 13 FINLUX 14 NOKIA
3
OK
PUSH JOG
IMPORTANT
Although the provided remote control unit is compatible with JVC televisions, as well as many other models, it may not work with your TV, or in some instances, may have limited function capability.
Control Your TV Using Addi­tional Buttons
The NUMBER keys on the remote can also be used to select the TV’s channel by setting the remote control to the TV mode.
1 Set the TV/VCR switch to TV. 2 Use the NUMBER keys, and the DIGIT ENTRY ( )
button, the PUSH JOG button, the DISPLAY button or the OK button to select the TV’s channel.
With televisions under Code 01, 03, 04, 06, 07, 10 or 11,
the DIGIT ENTRY button corresponds to the 1-digit/2­digit entry switching button (often labelled – /– –) of your TV’s remote control.
With televisions under Code 01, 08 or 09, the PUSH JOG button corresponds to the 10 + button, and the PUSH
%
%
JOG button corresponds to the 20 + button of your TV’s remote control.
With televisions using Code 09, the DISPLAY button corresponds to the 30 + button.
With televisions using Code 06, the OK button corre- sponds to the ENTER button of your TV’s remote control.
NOTE:
The way these buttons are used is determined by your TV. Use these buttons as instructed for your TV’s remote control.
USING THE CONFIRMATION SCREEN
EN 31
Storing Channels Manually
Store channels that were not stored during Auto Channel Set.
ACCESS CH. SET MODE MENU
Press and hold CH SET for more than 2 seconds. The Language screen appears. Press OK. The Ch. Set Mode
1
menu appears.
SELECT MODE
Press PUSH JOG%fi to select “MANUAL CH SET”, then press OK. The Confirmation screen appears.
2
SELECT POSITION
Press PUSH JOG%fi until an open position in which you want to store a channel begins blinking,
3
then press OK. The Manual Ch. Set screen appears.
INPUT CHANNEL
The number "02" appears blinking beneath "CH". Press the NUMBER keys to input the channel number
4
you want to store.
For fine tuning adjustment, press PUSH JOG until
the item beneath "CH" begins blinking, then press PUSH JOG%fi. While tuning, “F+” or “F–” appears.
If necessary, to change the band between CH(regular)
and CC(cable), press PUSH JOG until CH or CC is blinking, then press PUSH JOG %fi to select the band.
When storing a channel that sends scrambled
broadcasts, press PUSH JOG until "DECODER" blinks, then press PUSH JOG to "ON" ("OFF" is the default setting).
ENTER NEW CHANNEL INFORMATION
Press OK or STORE, and the Confirmation screen appears.
5
Repeat steps 3 through 5 as necessary.
%
%
%
%
%
%
to set "DECODER"
Perform steps 1 and 2 of the previous procedure to access the Confirmation screen before continuing.
Delete A Channel
SELECT ITEM
Press PUSH JOG delete begins blinking.
%
%
until the item you want to
%
1
DELETE CHANNEL
Press CANCEL.
The item directly beneath the cancelled one moves
2
up one line.
Repeat steps 1 and 2 as necessary.
CLOSE CONFIRMATION SCREEN
Press CH SET.
3
Change Station Channel Position
SELECT ITEM
Press PUSH JOG%fi until the item you want to move begins blinking. Then press OK and the station
1
name (ID) and its channel (CH) number begin blinking.
SELECT NEW POSITION
Press PUSH JOG%fi to move the station to the new channel position, then press OK.
2
Example: If you moved the station in position 3 to
position 7, the stations originally in positions 4–7 each move up one space.
Repeat steps 1 and 2 as necessary.
%
%
%
%
CLOSE CONFIRMATION SCREEN
Press CH SET.
To input the station name, see page 30.
6
To change positions, see "Change Station Channel Position" (at right).
When Receiving A Scrambled Broadcast
Make sure that the AV2 SELECT switch is set to "DECODER" (Z pg. 4).
1– Perform steps 1 and 2 above. 2– Press PUSH JOG
channel broadcasting the scrambled programmes, then press OK
3– Press PUSH JOG until "DECODER" begins blinking, and
set it to "ON" by pressing PUSH JOG
4– Press OK to access the Confirmation screen.
Repeat steps 2 – 4 for each additional channel.
5– Press CH SET.
three times.
%
%
to select the position of the
%
%
.
CLOSE CONFIRMATION SCREEN
Press CH SET.
3
32 EN
USING THE CONFIRMATION SCREEN (cont.)
Perform steps 1 and 2 of "Storing Channels Manually" on page 31 to access the Confirmation screen before continuing.
Set Stations (A)
SELECT ITEM
Press PUSH JOG%fi until the item you want begins blinking. Then press OK twice and the station’s name
1
(ID) begins blinking.
%
%
SELECT NEW STATION
Press PUSH JOG%fi until the new station’s name (ID) you want to store begins blinking.
2
Registered station names (Z pg. 33) appear as you press PUSH JOG%fi.
SWITCH STATIONS
Press OK.
Repeat steps 1 through 3 as necessary.
3
CLOSE CONFIRMATION SCREEN
Press CH SET.
4
Fine-Tuning Channels Already Stored
SELECT CHANNEL TO FINE-TUNE
Press PUSH JOG%fi until the channel you want to tune begins blinking.
%
%
1
ACCESS MANUAL CH. SET SCREEN
Press OK three times. The Manual Ch. Set screen appears.
2
PERFORM TUNING
Press PUSH JOG%fi until the picture is its clearest. Then press OK.
3
The Confirmation screen appears.
Repeat steps 1 through 3 as necessary.
CLOSE CONFIRMATION SCREEN
Press CH SET.
4
Set Stations (B)
NOTE:
First perform step 1 of the above procedure.
SELECT STATION NAME CHARACTER
Press PUSH JOG and the first letter of the station name begins blinking.
%
2
ENTER NEW CHARACTER
Press PUSH JOG%fi to cycle through the characters (A–Z, 0–9, –, *, +, (space)) and stop when the
3
desired one is indicated, then press PUSH JOG to enter. Enter the remaining characters the same way (maximum of 4). After entering all characters, press OK.
Repeat steps 1 through 3 as necessary.
If you make a mistake, press PUSH JOG until the
incorrect character begins blinking. Then enter the correct character by pressing PUSH JOG%fi .
CLOSE CONFIRMATION SCREEN
Press CH SET.
]
%
%
4
TV STATION AND ID LIST
EN 33
ID* STATION NAME
1000 TV1000 3SAT 3SAT ADLT ADULT ANT3 ANTENA3 ARD ARD ARTE ARTE BBC BBC GROUP BBC1 BBC1 BBC2 BBC2 BR3 BAYERN3 C+ CANAL PLUS C1 PORTUGUSES CAN5 CANALE5 CH4 CHANNEL4 CH5 CHANNEL5 CHLD CHILD CINE CINEMA CLUB TELECLUB CMT CMT CNN CNN CSUR ANDALUCIA DISC DISCOVERY DR DR TV DRS DRS DSF DSF ETB1 ETB1 ETB2 ETB2 EURO EURONEWS EUSP EUROSPORTS FEMM FEMMAN FILM FILM FNET FILMNET FR2 France2 FR3 France3 GALA GALAVISION HR3 HESSEN3 INFO INFO-KANAL ITA1 ITALIA1 ITA7 ITALIA7 ITV ITV JSTV JSTV KA2 KA2 KAB1 KABEL1 KAN2 KANAL2 LOCA LOCAL M6 M6 MBC MBR MCM MCM MDR MDR MOVE MOVIE MTV MTV MTV3 MTV3 N3 NORD3 N-TV N-TV NBC NBC SUPER NDR NDR NED1 NED1 NED2 NED2 NED3 NED3 NEWS NRK NRK ODE ODEON ORF1 ORF1
ID* STATION NAME
ORF2 ORF2 ORF3 ORF3 OWL3 OWL3 PREM PREMIERE PRO7 PRO7 RAI1 RAI1 RAI2 RAI2 RAI3 RAI3 RET4 RETE4 21 TELE21 RTBF RTBF1 or 2 RTL RTL RTL2 RTL2 RTL4 RTL4 RTP RTP S4 SCHWEIZ4 SAT1 SAT1 SBS SBS SHOW SHOW SIC SOCIEDADE SKY SKY CHANNEL SKYN SKY NEWS SPRT SPORT SRTL SUPER RTL STAR STAR-TV SVT1 SVT1 SVT2 SVT2 SW3 SUEDWEST3 TCC TCC TELE TELE TEL5 TELE5 TF1 TF1 TM3 TM3 TMC TELEMONTECARLO TNT TNT INT TRT TRT INT TSI TSI TSR TSR TV1 BRTN TV1 TV2 BRTN TV2 TV3 TV3 TVE1 TVE1 TVE2 TVE2 TVG TV GALICIA TVI TV INDEPENDENT TVN TV NORGE VCR VIDEO VERO VERONICA VH-1 VH-1 VIVA VIVA VIV2 VIVA2 VMTV VIDEO MUSIC VOX VOX VT4 VT4 VTM VTM WDR1 West1 WDR3 West3 YLE1 YLE1 YLE2 YLE2 ZDF ZDF ZTV ZTV
* The ID designator appears on your recorder's front display
panel and in the on-screen listing.
34 EN
Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair.
TROUBLESHOOTING
POWER
SYMPTOM
1. No power is applied to the recorder.
2. The clock is functioning properly, but the recorder cannot be powered.
TAPE TRANSPORT
SYMPTOM
1. The tape does not run during recording.
2. The tape stops during rewind or fast-forward.
3. The tape will not rewind or fast­forward.
PLAYBACK
SYMPTOM
1. The playback picture does not appear while the tape is running.
2. Noise appears during visual search.
3. Noise appears during normal playback.
4. Noise appears during slow-motion playback.
5. Noise appears during still play­back.
6. The playback picture is blurred or interrupted while TV broadcasts are clear.
POSSIBLE CAUSE
The mains power cord is discon­nected.
“ is displayed on the display panel.
POSSIBLE CAUSE
^“ is displayed on the display panel.
M“ is displayed on the display panel.
The tape is already fully rewound or fast-forwarded.
POSSIBLE CAUSE
If you’re using the RF OUT connec­tion, the TV receiver’s channel selector is set to the wrong video channel.
If you’re using the AV connection, the TV receiver is not set to the AV mode.
This is normal.
The automatic tracking mode is
engaged.
The automatic tracking mode is engaged.
The video heads may be dirty.
CORRECTIVE ACTION
Connect the mains power cord.
Press the TIMER button to turn the ““ indicator off.
CORRECTIVE ACTION
Press PLAY to turn the “^“ indicator off.
Press C.MEMORY to deactivate the Counter Memory function and turn the “M“ indicator off.
Check the cassette.
CORRECTIVE ACTION
If you are using the RF OUT connec­tion, set the TV receiver to the RF converter channel (UHF 36). (Z pg. 3)
If you are using the AV connection, set the TV to its AV mode.
Try manual tracking. (Z pg. 11)
Try manual tracking. (Z pg. 11)
Press TV PROG. + or – a few times to remove the noise bars from the screen.
Consult your JVC dealer.
RECORDING
SYMPTOM
1. Recording cannot be started.
2. TV broadcasts cannot be recorded.
POSSIBLE CAUSE
There is no cassette loaded, or the cassette loaded has had its Record Safety tab removed.
“AU” has been selected as the input mode.
CORRECTIVE ACTION
Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed.
Set to the desired channel.
EN 35
3. Tape-to-tape editing is not possible.
4. Camcorder recording is not possible.
TIMER RECORDING
SYMPTOM
1. Timer recording won’t work.
2. On-screen timer programming is not possible.
3. ““ and “]“ on the display panel won’t stop blinking.
4. The cassette is automatically ejected, and ““ and “]“ on the display panel won’t stop blinking.
5. ““ blinks for 10 seconds and the Timer mode is disengaged.
6. The cassette is automatically ejected, the power shuts off and ““ and “]“ won’t stop blinking.
7. ShowView does not timer-record properly.
The source (another video recorder, camcorder) has not been properly connected.
All necessary power switches have not been turned on.
The input mode is not correct.
The camcorder has not been
properly connected.
The input mode is not correct.
POSSIBLE CAUSE
The clock and/or the timer have been set incorrectly.
The timer is not engaged.
Timer recording is in progress.
The timer is engaged but there’s no
cassette loaded.
The loaded cassette has had its Record Safety tab removed.
TIMER has been pressed when there are no programs in memory, or the timer record information has been programmed incorrectly.
The end of the tape was reached during timer recording.
The recorder’s channel positions have been set incorrectly.
Confirm that the source is properly connected.
Confirm that all units’ power switches are turned on. Set the input mode to “AU”.
Confirm that the camcorder is properly connected.
Set the input mode to “AU”.
CORRECTIVE ACTION
Re-perform the clock and/or timer settings. Press TIMER and confirm that ““ is displayed on the display panel.
Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes.
Load a cassette with the Record Safety tab intact, or cover the hole using adhesive tape.
Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the Record Safety tab intact.
Check the programmed data and re­program as necessary, then press TIMER again.
The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.
Refer to "Guide Prog. Number Set" and re-perform the procedure (Z pg. 20).
OTHER PROBLEMS
SYMPTOM
1. Whistling or howling is heard from the TV during camcorder record­ing.
2. When scanning channels, some of them are skipped over.
3. The channel cannot be changed.
4. The remote control won’t operate the TV.
5. Channel settings that were made manually seem to have changed or disappeared.
POSSIBLE CAUSE
The camcorder’s microphone is too close to the TV.
The TV’s volume is too high.
Those channels have been desig-
nated to be skipped.
Recording is in progress.
The TV/VCR switch is in the wrong
position.
After the manual settings were made, Auto Channel Set was performed.
CORRECTIVE ACTION
Position the camcorder so its microphone is away from the TV. Turn the TV’s volume down.
If you need the skipped channels, restore them (Z pg. 31).
Press PAUSE to pause the recording, change channels, then press PLAY to resume recording.
Set the switch to TV.
Perform manual setting again.
36 EN
QUESTIONS AND ANSWERS
PLAYBACK
Q. What happens if the end of the tape is reached
during playback or search?
A. The tape is automatically rewound to the beginning.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
Q. Can the video recorder indefinitely remain in the
still mode?
A. No. It stops automatically after 5 minutes to protect
the heads.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
Q. During search, slow, still and frame-by-frame
playback, I can’t hear any audio. What’s the problem?
A. This is normal.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
Q. When returning from multi-speed search to normal
playback, the picture is disturbed. Should I be concerned about this?
A. No, it is normal.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
Q. Noise bars appear during multi-speed search. What’s
the problem?
A. This is normal.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
Q. Other than preventing further recording, what effect
does removing the Record Safety tab have?
A. It disables marking of index codes.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
Q. Sometimes, during Index Search, the video recorder
can’t find the programme I want to see. Why not?
A. There may be index codes too close together.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
RECORDING
Q. When I pause and then resume a recording, the end
of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen?
A. This is normal. It reduces distortion at the pause and
resume points.
○○○○○○○○○○○○○○○○○○○○○○○○○○
Q. Can the video recorder indefinitely remain in the
Record-Pause mode?
A. No. The video recorder goes to its Stop mode auto-
matically after 5 minutes to protect the heads.
○○○○○○○○○○○○○○○○○○○○○○○○○○
Q. What happens if the tape runs out during recording? A. The video recorder automatically rewinds it to the
beginning.
○○○○○○○○○○○○○○○○○○○○○○○○○○
TIMER RECORDING
Q. " " and "" remain lit on the display panel. Is
there a problem?
A. No. This is a normal condition for a timer recording in
progress.
○○○○○○○○○○○○○○○○○○○○○○○○○○
Q. Can I program the timer while I’m watching a tape
or a TV broadcast?
A. You won’t see the picture as it is replaced by the on-
screen menu, but the audio from the program or tape you’re viewing can be heard.
○○○○○○○○○○○○○○○○○○○○○○○○○○
ATTENTION:
This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.
INDEX
FRONT VIEW
EN 37
1
OPERATE TIMER
VIDEO AUDIO
3 4 5
2
+
TV PROG SP/LP
!
AUTO SP/LP
TIMER
@
D
W
SP LP
I T R
EP
*Remove the cap to use the front panel connectors.
1 OPERATE Button (Z pg. 5) 2 TIMER Button (Z pg. 23) 3 TV PROG. +/– Buttons (Z pg. 5) 4 SP/LP [Tape Speed] Button [E439EG](Z pg. 15)
COUNTER MEMORY Button [E239EG](Z pg. 14)
5 AUTO SP/LP TIMER Button [E439EG](Z pg. 26)
COUNTER RESET Button [E239EG](Z pg. 14)
6 Cassette Loading Slot 7 RECORD Button (Z pg. 15) 8 PAUSE Button (Z pg. 10)
6
VIDEO
REMAIN
D
M
#
7
$
8 9
AUDIO
DUBBING
REW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
^
0
& %
9 TV PROG. Dial (Z pg. 15)
JOG Dial (Z pg. 10)
0 SHUTTLE Ring (Z pg. 10) ! VIDEO and AUDIO Input Connectors (Z pg. 27) @ Infrared Beam Receiving Window # Display Panel (Z pg. 38) $ AUDIO DUBBING Button [E439EG](Z pg. 27)
DISPLAY Button [E239EG](Z pg. 14)
% REVIEW Button (Z pg. 11) ^ STOP/EJECT Button (Z pg. 9) & PLAY Button (Z pg. 9)
0
0
0
FF
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
TV PROG./
JOG
SHUTTLE
REAR VIEW
1
AV2 SELECT
/ RF TEST
DECODER
OFF ON
AV2
5
1 Mains Power Cord (Z pg. 3) 2 AV1 IN/OUT Connector (Z pg. 3) 3 AV2 IN/DECODER Connector (Z pg. 4) 4 ANT. IN Connector (Z pg. 3) 5 AV2 SELECT/RF TEST Switch (Z pg. 4)
2
3
AV2 IN/DECODER
AV1 IN/OUT
PAUSE
RF OUT
4
ANT. IN
32 40
68
7
6 Remote PAUSE Connector [E439EG only]
(Z pg. 29)
7 RF OUT Connector (Z pg. 3) 8 RF Output Channel Adjustment Screw (Z pg. 4)
38 EN
DISPLAY PANEL
INDEX (cont.)
1
25
D
W
SP LP
I T R
EP
0#! $ %
@
D
M
63478
REMAIN
VIDEO
9
1 and 2 Symbolic Mode Indicators 3 ”DAILY” Program Mark (Z pg. 23)
4 ”WEEKLY” Program Mark (Z pg. 23)
PLAY:
STILL: FORWARD SLOW:
5 Start Time/Stop Time Indicator (Z pg. 22) 6 Tape Remaining Time Indicator (Z pg. 14) 7 PDC/VPS Indicator (Z pg. 26)
FF:
REW: RECORD:
FF VARIABLE SHUTTLE SEARCH:
REW VARIABLE AUDIO SHUTTLE SEARCH: DUBBING: **
REVERSE PLAY:
STILL: REVERSE SLOW:
RECORD PAUSE:
*
*
AUDIO DUBBING PAUSE:
**
8 VIDEO Indicator (Z pg. 5) 9 B.E.S.T. Picture System Display (Z pg. 16) 0 ”Cassette Loaded” Mark ! Instant Timer Recording (Z pg. 19) @ Tape Speed Indicators [E439EG only](Z pg. 15) # ”Timer” Indicator (Z pg. 23) $ Clock/Counter/Tape Remaining Time Display
(Z pg. 7)
% Channel/Mode Display (Z pg. 5)
** The indicator will blink during turbo search.
** E439EG only
REMOTE CONTROL
EN 39
1
CH SET
STORE
2 3 4
5 6
7 8
9 0
A
12 45
7
C.RESET
CANCEL
START
B
EXPRESS PROGRAMMING
AUDIO MONITOR
C.MEMORY
DISPLAY
2
ADD TIME
DAILY
8
AUX
0
DATESTOP
TV/VIDEO
(MONITOR)
TV VCR
! @ # $
R
E
D
N
I
F
E
N
E
C
S
O
R
P
1
P
R
3
G
O
K
V
O
L
.
V
T
%
PUSH JOG
^
E
D
I
I
L
U
L
G
&
1 CH SET Button (Z pg. 5) 2 REVIEW Button (Z pg. 11) 3 A/B CODE Switch (Z pg. 14) 4 CLOCK Button (Z pg. 7)
U
I
M
MULTI BRAND
REMOTE CONTROL UNIT
OPERATE
MODECLOCK
3 6
WEEKLY
9
TIMER
TV
PROG.
O
G
C
H
E
C
K
* ( )
q w e
r t
y u i
o p Q
W E
R T
Y U
5 NUMBER Keys (Z pg. 15) 6 (PDC/VPS) Button (Z pg. 26)
7 CANCEL Button (Z pg. 21)
C.RESET Button (Z pg. 14)
8 START +/– Button Z pg. 24) 9 STOP +/– Button (Z pg. 24) 0 SP/LP Button (Z pg. 11)
DIGIT ENTRY Button (Z pg. 30)
! TV MUTE Button (Z pg. 30) @ Rewind [REW] Button (Z pg. 9) # PLAY Button (Z pg. 9) $ RECORD Button (Z pg. 15) % SCENE FINDER Button (Z pg. 13) ^ PROG Button (Z pg. 22) & PUSH JOG %fi Button (Z pg. 5)
PUSH JOG Button (Z pg. 10)
%
%
%
%
* STORE Button (Z pg. 31)
C.MEMORY Button (Z pg. 14)
( OPERATE Button (Z pg. 5) ) DISPLAY Button (Z pg. 14) q MODE Button (Z pg. 16) w ADD TIME Button (Z pg. 23) e DAILY Button (Z pg. 23) r WEEKLY Button (Z pg. 23) t AUX Button (Z pg. 27) y TIMER Button (Z pg. 23) u TV PROG. +/– Button (Z pg. 5) i DATE +/– Button (Z pg. 25) o TV/VCR Switch (Z pg. 30) p TV/VIDEO Button (Z pg. 5) Q Fast Forward [FF] Button (Z pg. 9) W PAUSE Button (Z pg. 10) E STOP Button (Z pg. 9) R PROG CHECK Button (Z pg. 26) T OK Button (Z pg. 5) Y TV VOL %fi Button (Z pg. 30) U ILLUMI GUIDE Button (Z pg. 22)
Installing Batteries
1 Open the battery compartment cover. 2 Insert 2 "R6"-size batteries (provided) in the correct
directions.
3 Replace the cover.
How To Use
The remote control can operate most of your video recorder's functions, as well as basic functions of TV sets of JVC and other brands (Z pg. 30).
Point the remote control toward the sensor window.
The maximum operating distance of the remote control
is about 8 m.
NOTE:
If for some reason the remote control doesn't work properly, remove its batteries, wait a short time and then try again.
SPECIFICATIONS
GENERAL
Power requirement : AC 220 – 240 V` , 50/60 Hz Power consumption : 20 W Temperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD) : 426 x 94 x 341 mm Weight : 4.5 kg Format : VHS PAL standard Maximum recording time
(SP) : 240 min. with E-240 video cassette
(LP)[E439EG only] : 480 min. with E-240 video cassette
VIDEO/AUDIO
Signal system : PAL-type colour signal and CCIR monochrome signal,625 lines
50 fields
Recording system : DA4 (Double Azimuth) head helical scan system (HR-E439EG)
: Rotary two-head helical scan system (HR-E239EG) Signal-to-noise ratio : 45 dB Horizontal resolution : 250 lines Frequency range : 70 Hz to 10,000 Hz Input/Output : 21-pin scart connectors (IN/OUT x 1, IN/DECODER x 1)
RCA connectors (VIDEO IN x 1, AUDIO IN x 1)
EN
HR-E439EG/239EG
TUNER/TIMER
TV channel storage capacity : 99 positions (+AUX position "AU") Tuning system : Frequency synthesized tuner Channel coverage : VHF 47 – 89/104 – 300/
Aerial output : UHF channel 36 (Adjustable 32 – 40) Memory backup time : Approx. 60 min.
ACCESSORIES
Provided accessories : RF cable,
Specifications shown are for SP mode unless otherwise specified. E.& O.E. Design and specifications subject to change without notice.
302 – 470MHz
UHF 470 – 862MHz
Infrared remote control unit, "R6" battery x 2
VICTOR COMPANY OF JAPAN, LIMITED
COPYRIGHT © 1996 VICTOR COMPANY OF JAPAN, LTD.
EG
Printed in Japan 0796YOV*UN*SN
Loading...