JVC HR-DD949E, HR-DD949EH Instruction Manual

ENGLISH

SEE 

AUTO SET UP

ON REAR SIDE

CONTENTS

SAFETY FIRST 2

Safety Precautions ...................... 2

INSTALLING YOUR NEW RECORDER 3

Basic Connections......................3

VIDEO CASSETTE RECORDER

INITIAL SETTINGS 4

Auto Set Up ............................... 4

Language ................................... 7

Video Channel Set...................... 8

SHOWVIEW Setup ....................... 10

HR-DD949E/EH

PLAYBACK 12

Basic Playback ......................... 12

Playback Features..................... 13

TimeScan ................................. 18

RECORDING 21

Basic Recording ....................... 21

B.E.S.T. Picture System ............. 22

On-Screen Displays.................. 24

Recording Features................... 25

TIMER RECORDING 28

SHOWVIEW Timer Recording....... 28

Regular Timer Programming ..... 30

EDITING 34

C.MEMORYDISPLAY

12453

ADD TIME

DAILY

807

AUX

C.RESET

CANCEL

DATESTOP

START

EXPRESS PROGRAMMING

AUDIO MONITOR

TV/VCR

(MONITOR)

PUSH JOG

MULTI BRAND

REMOTE CONTROL UNIT

WEEKLY

TIMER

TV

PROG.

VCR

SAT

STANDBY/ON

TIMER

3R PICTURE

AUTO SP/LP

+8 4 0

TIMER

SP LP

–20dB

VCR

REMAIN

NORM

REVIEW

REW

SP/LP

TV PROG/

JOG

SHUTTLE

Edit To Or From Another Video

Recorder .................................. 34

Edit From A Camcorder............ 36

Audio Dubbing ........................ 37

Insert Editing ............................ 38

INFORMATION ON J TERMINAL 40 SYSTEM CONNECTIONS 41

Connecting/Using A Decoder ... 41

SPECIAL FEATURES 42

TV Multi-Brand Remote

Control..................................... 42

PAL

Satellite Tuner Multi-Brand

Remote Control ........................ 43

TUNER SET 44 CLOCK SET 49 TROUBLESHOOTING 51 QUESTIONS AND ANSWERS 53

INSTRUCTIONS

INDEX 54 SPECIFICATIONS 57

LPT0002-027B

2 EN

SAFETY FIRST

Safety Precautions

The rating plate and the safety caution are on the rear of the unit.

WARNING: DANGEROUS VOLT AGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

CAUTION

n When you are not using the recorder for a long period of

time, it is recommended that you disconnect the power cord from the mains outlet.

n Dangerous voltage inside. Refer internal servicing to

qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial.

WARNING

There are two different types of SECAM colour systems: SECAM-L, used in FRANCE (also called SECAM-West), and SECAM-B, used in Eastern European countries (also called SECAM-East).

1.This recorder can also receive SECAM-B colour television signals for recording and playback.

2.Recordings made of SECAM-B television signals produce monochrome pictures if played back on a video recorder of SECAM-L standard, or do not produce normal colour pictures if played back on a PAL video recorder with SECAM-B system incorporated (even if the TV set is SECAM-compatible).

3.SECAM-L prerecorded cassettes or recordings made with a SECAM-L video recorder produce monochrome pictures when played back with this recorder.

4.This recorder cannot be used for the SECAM-L standard. Use a SECAM-L recorder to record SECAM-L signals.

For Italy:

"It is declared that this product, brand JVC, conforms to the Ministry Decree n. 548 of 28 Aug.'95 published in the Official Gazette of the Italian Republic n. 301 of 28 Dec.'95"

PAL

IMPORTANT

n Please read the various precautions on this page before

installing or operating the recorder.

n It should be noted that it may be unlawful to re-record

pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein.

The STANDBY/ON button does not completely shut off mains power from the unit, but switches operating

current on and off. " and " " shows ON.

Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a single-speed video recorder.

Failure to heed the following precautions may result in damage to the recorder, remote control or video cassette.

1. DO NOT place the recorder . . .

... in an environment prone to extreme temperatures or

humidity. ... in direct sunlight. ... in a dusty environment. ... in an environment where strong magnetic fields are

generated. ... on a surface that is unstable or subject to vibration.

2. DO NOT block the recorder’s ventilation openings.

3. DO NOT place heavy objects on the recorder or remote control.

4. DO NOT place anything which might spill on top of the recorder or remote control.

5. AVOID violent shocks to the recorder during transport.

" shows electrical power standby

n Only cassettes marked "VHS" can be used with this

videorecorder.

n HQ VHS is compatible with existing VHS equipment. n With this recorder, the G-Code system is identified as

"SHOWVIEW" and is operated using the "SHOWVIEW" on screen menu. SHOWVIEW is a registered trademark of Gemstar Development Corporation. The SHOWVIEW system is manufactured under licence from Gemstar Development Corporation. G-Code is a trademark of Gemstar Development Corporation. The G-Code system is manufactured under license from Gemstar Development Coporation.

n Certain audio features of this product manufactured under a

license from Desper Products, Inc. Spatializert is a trademark owned by Desper Products, Inc.

MOISTURE CONDENSATION

Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form in the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the recorder turned on for a few hours to let the moisture dry.

ABOUT HEAD CLEANING

Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or interrupted. Be sure to contact your nearest JVC dealer if such troubles occur.

INSTALLING YOUR NEW RECORDER

It's essential that your video recorder be properly connected. Follow these steps carefully. THESE STEPS MUST BE COM-

Basic

PLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.

EN 3

Connections

Aerial terminal

Back of TV

21-pin SCART connector

TV Aerial Cable

21-pin SCART Cable

Mains Power Cord

Mains outlet

RF Cable (provided)

AV1 IN/OUT

AUDIO OUT(put) connectors

For connection to the audio input connctors on a Hi-Fi stereo system

Rear view

CHECK CONTENTS

Make sure the package contains all of the accessories listed in “Specifications” (Z pg. 57).

SITUATE RECORDER

Place the recorder on a stable, horizontal surface.

CONNECT RECORDER TO TV

The connection method you use depends on the type of TV you have.

RF CONNECTION

●

To Connect To A TV With NO AV Input Terminals . . .

a– Disconnect the TV aerial cable from the TV. b– Connect the TV aerial cable to the ANT. IN jack

on the rear panel of the recorder.

c– Connect the provided RF cable between the RF

OUT jack on the rear panel of the recorder and the TV’s aerial terminal.

Before operating the recorder, make sure the TV’s channel is set to the VIDEO channel (

AV CONNECTION

●

To Connect To A TV With AV Input Terminals . . .

a– Connect the aerial, recorder and TV as per “RF

CONNECTION”.

b– Connect an optional SCART cable between the

AV1 IN/OUT socket on the rear panel of the recorder and the TV’s 21-pin SCART connector. If you are using this recorder in Australia or New Zealand, see "For Customers in Australia and New Zealand" on this page.

Before operating the recorder, make sure the TV is set to the VIDEO (or AV) mode.

CONNECT RECORDER TO MAINS

Plug the end of the mains power cord into a mains outlet.

Z pg. 8).

After you plug the mains power cord into a mains outlet, the Country Set display appears on the TV screen and/or on the recorder's front display panel when the button on the recorder/remote control is pressed for the first time to power on the recorder; go to page 4 to perform Auto Set Up.

For Customers in Australia and New Zealand

Connect an optional AV cable between the TV's AV-IN terminals and the AV1 IN/OUT connector on the rear panel of the recorder via the provided output cable adapter as illustrated.

Output cable adapter (Provided)

AV cable

To AV-IN terminals

(Not provided)

Recorder

To AV1 IN/OUT connector

4 EN

Auto Set Up

Auto Channel Set/Auto Clock Set/Auto Guide Program Number Set

INITIAL SETTINGS

When the button on the recorder/remote control is pressed for the first time to power on the recorder after you plug the mains power cord into a mains outlet, the Country Set display will appear on the TV screen and the recorder's front display panel. By simply selecting your country*, the Auto Set Up function sets the tuner channels, clock and Guide Program numbers automatically.

*If you live in Belgium or Switzerland, you also need to select the

language you use.

You can refer to the front display panel and/or the on-screen display to perform this procedure.

12 45 7

PUSH JOG

International Telephone Country Code

SUOMI : 358 SUISSE : 41 PORTUGAL : 351 ITALIA : 39 DEUTSCHLAND : 49 ESPAÑA : 34 NORGE : 47 BELGIUM : 32 SVERIGE : 46 NEDERLAND : 31 DANMARK : 45 GREECE : 30 ÖSTERREICH : 43 OTHERS : - -

* Depending on the model, the selectable codes

may be limited.

8 0

3 6 9

ATTENTION

Once you have performed Auto Set Up, even if the recorder's memory backup has expired, all the stored stations and their Guide Program numbers remain in the recorder's memory and the recorder will not perform Auto Set Up again. You only need to set the clock. (Z pg. 49)

If you have moved to a different area, perform each setting as required.

● Tuner setting

● Clock setting Z pg. 49

● SHOWVIEW Guide Program number setting Z pg. 10

If a new station starts broadcasting in your area, perform both tuner setting (Z pg. 44) and SHOWVIEW Guide Program number setting (Z pg. 10).

Z pg. 44

Before starting, make sure of the following:

● The TV aerial cable should be connected to the recorder.

● The recorder's mains power cord should be connected to

a mains outlet. Z pg. 3

● If you want to use the on-screen display, the TV should

be set to its AV mode (with AV connection Z pg. 3) or UHF channel 36 (with RF connection Z pg. 3).

TURN ON THE RECORDER

Press on the recorder or remote control. The Country Set display appears on the front display panel

and/or on the screen.

For HR-DD949E For HR-DD949EH

DEUTSCHLAND ÖSTERREICH SUISSE ITALIA NEDERLAND GREECE

OTHERS

[5∞] = [MENU] : EXIT

For HR-DD949EH

PORTUGAL ESPAÑA BELGIUM

OTHERS

[5∞] = [MENU] : EXIT

SUOMI NORGE SVERIGE DANMARK

OTHERS

[5∞] = [MENU] : EXIT

* The on-screen display

differs for the HRDD949EH depending upon the country in which the product was purchased.

NOTE:

If you have connected your TV to the recorder with RF connection and the on-screen display appearing on UHF channel 36 looks distorted, perform this procedure referring to the front display panel.

SELECT COUNTRY

If you are referring to the front display panel

Press PUSH JOG%ﬁ to select your international

telephone country code of your country referring to the chart in the left column.

● If you have selected a country code other than 32 (BELGIUM) or 41 (SUISSE), go to step 4.

● If you have selected 32 (BELGIUM) or 41 (SUISSE), go to step 3.

CONTINUED ON NEXT PAGE.

EN 5

If you are referring to the on-screen display

Press PUSH JOG%ﬁ to move the highlight bar (pointer) to your country's name.

● If you have selected a country other than BELGIUM or SUISSE, go to step 4.

● If you have selected BELGIUM or SUISSE, go to step 3.

SELECT LANGUAGE

Press OK. the Language Set display appears on the front display panel and/or on the screen.

If you are referring to the front display panel

Press PUSH JOG%ﬁ to select your language code referring to the chart in the left column.

(Ex.) DEUTSCH is selected for SUISSE

International telephone country code

If you are referring to the on-screen display

Press PUSH JOG%ﬁ to move the highlight bar (pointer) to the language of your choice.

For HR-DD949E For HR-DD949EH

NEDERLANDS ITALIANO FRANCAIS

DEUTSCH

ENGLISH

[5∞] = [MENU] : ENDE

NEDERLANDS CASTELLANO FRANCAIS

DEUTSCH

ENGLISH

[5∞] = [MENU] : ENDE

PERFORM AUTO SET UP

Press OK.

"Auto" appears on the display panel and blinks; do NOT press any button on the recorder or remote control until the display panel shows the current time or "CH1" or "--:--". (Refer to box on this page.)

Language Code for the HR-DD949E

ENGLISH :01 ITALIANO :04 DEUTSCH : 02 NEDERLANDS : 05 FRANCAIS :03

Language Code for the HR-DD949EH

ENGLISH : 01 CASTELLANO : 04 DEUTSCH : 02 NEDERLANDS : 05 FRANCAIS : 03

Auto Set Up results appear on the front display panel

Language code

● When both auto channel set and auto clock set have been completed successfully the correct current time will be displayed.

● When auto channel set has been completed successfully but auto clock set has not, "CH" will be displayed.

● When neither auto channel set nor auto clock set has been completed successfully, "--:--" will be displayed.

● If Auto Set Up is completed, go to page 6.

● Auto channel set function takes place first; it assigns

automatically all receivable stations in your area.

● Auto clock set function sets the clock automatically by reading the clock setting data from a station transmitting a PDC signal while auto channel set is being performed.

● During auto channel set, the recorder recognizes each station name of the detected stations and stores them in the recorder's memory, then automatically sets SHOWVIEW assigned Guide Program number for those stations according to the broadcast area.

NOTE:

In the area where no TV station transmits a PDC signal, the recorder can perform neither auto clock set nor auto Guide Program number set.

NOTES:

●

If you are using the onscreen display, the AUTO SET screen will appear after pressing OK in step 4. As Auto Set Up progresses, the

" mark on the screen

" moves from left to right.

●

If there is a power cut, or if you press or MENU while Auto Set Up is in progress, Auto Set Up will be interrupted; be sure to turn off the recorder power once and try again from step 1.

[MENU] : EXIT

Beginning End

AUTO SET

PLEASE WAIT

+++

6 EN

If both auto channel set and auto clock set have been performed successfully:

Perform "Video Channel Set" on page 8.

1 2Turn on the TV and select its VIDEO channel or AV mode, then make sure that all necessary stations have been stored in the

recorder's memory by using the TV PROG. button(s).

● If station names (ID — Z pg. 48) have also been stored in the recorder's memory, the station name will be displayed at the top left corner of the screen for about 5 seconds when the recorder is tuned to a different station.

● If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 46 – 47.

3Perform "SHOWVIEW Setup" on page 10 to check if the Guide Program numbers have been set correctly.

If auto channel set has succeeded but auto clock set has not:

Perform "Video Channel Set" on page 8.

1 2Turn on the TV and select its VIDEO channel or AV mode, then make sure that all necessary stations have been stored in the

recorder's memory by using the TV PROG. button(s).

● If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or change station names, see pages 46 – 47.

3Perform "Clock Set" on page 49, then "SHOWVIEW Setup" on page 10 to check if the Guide Program numbers have been set

correctly.

If both auto channel set and auto clock set have failed:

1Make sure the TV aerial cable is connected properly to the recorder and turn off the recorder power once, then turn the

recorder power back on again.

● The Country Set display appears on the front display panel and/or on the screen; perform steps 2 and 4 on pages 4 – 5 again.

INITIAL SETTINGS (cont.)

IMPORTANT

● Depending on the reception conditions, the station names may not be stored correctly, and auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly, SHOWVIEW timer recording (Z pg. 28) will not work correctly; be sure to check if the Guide Program numbers have been set correctly (Z pg.10, "SHOWVIEW Setup").

● Since your video recorder memorizes all detected stations even if the reception condition is poor, some of those stored stations may produce a noisy picture. To delete those stations, Z "Delete A Channel" on page 46.

INFORMATION

Language for the on-screen display

Auto Set Up also selects the language automatically for the on-screen display depending on the Country setting you have made in step 2 on page 4 (unless you have selected BELGIUM or SUISSE), as shown below.

SUOMI [ SUOMI SVERIGE [ SVENSKA ESPAÑA [ CASTELLANO PORTUGAL [ ENGLISH DANMARK [ DANSK NEDERLAND [ NEDERLANDS DEUTSCHLAND [ DEUTSCH ÖSTERREICH [ DEUTSCH GREECE [ ENGLISH NORGE [ NORSK ITALIA [ ITALIANO OTHERS [ ENGLISH If you want to change the language setting manually, Z "Language" on page 7.

Just Clock

Your recorder is equipped with the Just Clock function which provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. If you want to take advantage of this function, simply set it to "ON".

Z "Just Clock" on page 49.

Language

● Be sure to set your Video Channel before performing Language setting (Z pg. 8).

● Turn on the TV and select the VIDEO channel (or AV mode).

12 45 7

8 0

3 6 9

EN 7

This recorder offers you the choice to view on-screen messages in 10 different languages. Though Auto Set Up selects the language automatically (Z pg. 6), you can change the language setting manually using this procedure as required.

TURN ON THE RECORDER

Press .

ACCESS MAIN MENU

Press MENU twice.

ACCESS COUNTRY SET SCREEN

Press PUSH JOG move the highlight bar

(pointer) to "AUTO CH SET", then press OK.

SELECT COUNTRY

Press PUSH JOG to your country's name, then press OK. The Language

Set screen appears.

ﬁ

to move the highlight bar (pointer)

ﬁ

MAIN MENU

MODE SET

AUTO CH SET

MANUAL CH SET GUIDE PROG SETT CLOCK SET JLIP ID NO. SET

[5∞] = [MENU] : EXIT

PUSH JOG

SELECT LANGUAGE

Press PUSH JOG%ﬁ to move the highlight bar (pointer) to the language of your choice.

For HR-DD949EH For HR-DD949EH

DANSK SUOMI NORSK SVENSKA

ENGLISH

[5∞] = [MENU] : EXIT

For HR-DD949E

NEDERLANDS ITALIANO FRANCAIS DEUTSCH

ENGLISH

[5∞] = [MENU] : EXIT

● You do not have to press OK; pressing OK starts Auto Channel Set.

NEDERLANDS CASTELLANO FRANCAIS DEUTSCH

ENGLISH

[5∞] = [MENU] : EXIT

* The on-screen display

differs for the HRDD949EH depending upon the country in which the product was purchased.

RETURN TO NORMAL SCREEN

Press MENU.

8 EN

TV PROG.+/–

STOP

Video Channel Set

INITIAL SETTINGS (cont.)

If you have connected the video recorder to your TV via the provided RF cable only (RF connection) – Go to "With RF Connection" below.

If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection) – Go to "With AV Connection" on next page.

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

12 45 7

8 0

3 6 9

TV PROG.

IMPORTANT:

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

With RF Connection

ACCESS VIDEO CHANNEL SET MODE

Hold down STOP on the recorder until the display panel shows the following.

SET VIDEO CHANNEL

Set your TV to UHF channel 36.

● If the two vertical white bars appear clearly on the

screen as shown in the illustration at bottom left, go to step 3.

● If the two vertical white bars do not appear clearly, press TV PROG.+ or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area.

(Ex.) If channel 50 is available in your area

Then set your TV to UHF channel 50 and check if the two vertical white bars appear clearly on the screen; if so, go to step 3. If not, re-set the video recorder to another vacant channel and try again.

NOTES:

●

If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●

If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

TEST SIGNAL

The channel on which the screen to the left appear clearly in step 2 is your Video Channel.

To view picture signals from the video recorder, set your TV to the Video Channel.

EXIT VIDEO CHANNEL SET MODE

Press OK.

EN 9

STOP

TV PROG.

IMPORTANT:

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

12 45

3 6 9

TV PROG.

With AV Connection

ACCESS VIDEO CHANNEL SET MODE

Hold down STOP on the recorder until the display panel shows the following.

SET VIDEO CHANNEL

Press TV PROG. – until the display panel shows

– –

"–OUT

● Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

Press OK.

To view picture signals from the video recorder, set your TV to its AV mode.

10 EN

SHOWVIEW Setup

INITIAL SETTINGS (cont.)

With SHOWVIEW, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise.

NOTE:

“Guide Program (GUIDE PROG) Number” refers to the assigned TV station numbers, according to broadcast area, for S timer recording.

HOWVIEW

Turn on the TV and select the VIDEO channel (or AV mode).

* For Customers in Australia and New Zealand:

With this recorder, the G-Code system is identified as "SHOWVIEW".

NUMBER

CANCEL

PUSH JOG

12 45 7

8 0

3 6 9

IMPORTANT

Perform the following procedure after Auto Set Up on page 4 and/or the channel setting steps on pages 44 – 47, and after the Clock Set procedure on page 49. After setting the Guide Program Numbers, the station names and channel positions may be incorrect if you stored or skipped channels. In this case, re-perform Guide Program Number setting.

Guide Program Number Set

MAKE LIST OF STORED STATION NAMES AND CHANNEL POSITIONS

(Ex.)

Channel position Station name

1 ARD 2 ZDF 3 WDR

ACCESS MAIN MENU SCREEN

Press MENU twice.

ACCESS GUIDE PROG SET SCREEN

Press PUSH JOG %ﬁ to move the highlight bar (pointer) to "GUIDE PROG SET", then press OK.

The Guide Prog. Set screen appears.

MAIN MENU

MODE SET AUTO CH SET MANUAL CH SET

GUIDE PROG SET

CLOCK SET JLIP ID NO. SET

[5∞] = [MENU] : EXIT

GUIDE PROG TV PROG

: AUTO SET BY SHOWVIEW

[ ]: MANUAL SET [5∞] : ? [MENU] : EXIT

GUIDE PROG SET

EN 11

ENTER SHOWVIEW NUMBER

Press OK, and a cursor appears above “GUIDE

PROG”. Then, using the NUMBER keys, input the SHOWVIEW number (found in most TV listings) of a program scheduled to be broadcast on each station on the list from step 1, starting at the top. If you enter the wrong number, press CANCEL to backspace and input the correct number.

GUIDE PROG SET

12345

GUIDE PROG TV PROG

[0-9] = [MENU] : EXIT

When entering a S number for ZDF

HOWVIEW

CONFIRM CHANNEL POSITION NUMBER

Press OK and the display

under “TV PROG” begins

blinking.

If the blinking number under “TV PROG” agrees with the channel position . . .

. . . press OK.

If the numbers do not agree . . .

. . . input the channel position using PUSH JOG%ﬁ or the NUMBER keys, then press OK.

● If you input the SHOWVIEW number of a program that has already aired, “ERROR” appears on screen for a few seconds. Input the correct SHOWVIEW number.

● Repeat steps 4 and 5 as necessary.

GUIDE PROG SET

GUIDE PROG TV PROG

[5∞] = [MENU] : EXIT

CLOSE MENU

Press MENU and selection is complete.

If you already know the Guide Program number for a station . . . 1– After step 3, press PUSH JOG .

● The GUIDE PROG number begins blinking.

2– Enter the Guide Program number using the NUMBER keys

or PUSH JOG%ﬁ, then press PUSH JOG .

● The TV PROG number begins blinking.

3– Enter the channel position using the NUMBER keys or

PUSH JOG%ﬁ, then press PUSH JOG .

● Repeat 2 and 3 as necessary.

4– Press MENU.

When Using A Satellite Tuner

Satellite Antenna

Ex. 1

Satellite Tuner

AV2 IN/ DECODER

TV Receiver

Preparation 1– Connect the satellite tuner to the AV2 IN/DECODER

connector on the rear of your recorder.

2– Set "AV2 SELECT" to "AV2" (Z pg. 34). To Record Satellite Broadcasts . . .

1– Select the appropriate channel on the satellite tuner. 2– Press NUMBER key "0" to set your recorder's input mode to

"AUX2".

3– Start recording ( To Record Satellite Broadcasts Using S

Recording . . . 1– Perform Guide Program Number setting.

● In step 5 in the left column, press NUMBER key "0" to set "TV PROG" to "AUX2".

2– Perform SHOWVIEW Timer Recording (Z pg. 28). T o Record Satellite Broadcasts Using Regular Timer Recording . . .

1– In step 6 on page 31, press TV PROG. +/– to set the channel

position to "AUX2".

Ex. 2

Satellite Tuner and Decoder

Z pg. 21, steps 3 – 6).

NOTE:

When timer-recording a satellite programme, first set the satellite tuner to the appropriate channel before the selected programme begins and then set the satellite tuner's timer. If your satellite tuner does not have a timer, leave it switched on.

Aerial or Cable

Rear view

For Customers in Australia and New Zealand:

When connecting the AV cable, use the input and/or output cable adapter.

HOWVIEW Timer

12 EN

PLAY

STOP

PLAY TIME SCAN SHUTTLE

REW

Basic

PLAYBACK

The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.

Playback

Turn on the TV and select the VIDEO channel (or AV mode).

STOP/EJECT

LOAD A CASSETTE

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is

point toward the recorder. Don’t apply too much pressure when inserting.

● The recorder power comes on automatically and the counter is reset to 0:00:00.

● If the record safety tab has been removed, playback begins automatically.

FIND PROGRAMME START POINT

If the tape is advanced past the start point, press REW or turn the TIME SCAN SHUTTLE ring to the left.

To go forward, press FF or turn the TIME SCAN SHUTTLE ring to the right.

START PLAYBACK

Press PLAY. “BEST” appears blinking in the recorder's display panel during automatic tracking. (Z pg. 22)

STOP PLAYBACK

Press STOP on the remote or STOP/EJECT on the recorder’s front panel. Then press STOP/EJECT to

remove the cassette.

REW

12 45

3 6 9

Usable cassettes

● Compact VHS camcorder recordings can be played on this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.

● This video recorder can record on regular VHS and Super VHS cassettes. However, it will record and play back regular VHS signals only. It is not possible to play back a recorded Super VHS tape.

EN 13

PLAY

REW

JOG

TIME SCAN SHUTTLE

PAUSE

TV PROG.

Take advantage of special functions possible with the recorder’s controls or the remote control.

Playback Features

PLAY

REW

TV PROG.

PAUSE

Still Picture/Frame-By-Frame Playback

PAUSE DURING PLAYBACK

Press PAUSE. If there is vertical jitter, use the TV PROG. buttons to correct the picture.

● During still picture, the sound from the previous 3 seconds (approx.) will be played back repeatedly (provided there was at least 6 seconds of normal

playback prior to engaging the still picture mode). However, the TIME SCAN indicator will not light.

● "TIME SCAN AUDIO" must be set to "ON", or the sound will not be heard. (Z pg. 20)

ACTIVATE FRAME-BY-FRAME PLAYBACK

Turn the JOG dial to the right for forward frame-byframe playback, or to the left for reverse frame-by-frame

playback.

Press PAUSE.

Press PUSH JOG or .

To resume normal playback, press PLA Y.

Slow Motion

PUSH JOG

High-Speed (Turbo) Search

ACTIVATE HIGH-SPEED SEARCH

During playback or still picture, press FF for forward high-speed search, or REW for reverse high-speed

search.

To resume normal playback, press PLAY.

NOTES:

●

For short searches, press and hold FF or REW for over 2 seconds. When released, normal playback resumes.

●

Picture may not appear during search with an LP-recorded tape.

●

In the search, still, or frame by frame playback mode, the picture may be distorted, and there may be a loss of colour.

ACTIVATE SLOW-MOTION PLAYBACK

Turn the TIME SCAN SHUTTLE ring to the left or press PUSH JOG during playback to decrease speed in the

forward direction. To play in reverse slow-motion (and in reverse play mode), continue to turn the TIME SCAN SHUTTLE ring to the left or press PUSH JOG after selecting all the forward direction slow-motion modes.

During still picture, turn the TIME SCAN SHUTTLE ring to the right for forward slow motion, or to the left for reverse slow motion.

During still picture, press and hold PAUSE for 2 seconds, then release. Press and release again to return to still picture.

During still picture, press and hold PUSH JOG or . Release to return to still picture.

To resume normal playback, press PLAY.

ﬁ

14 EN

PLAY 3R PICTURE

TV PROG.

PLAY

REW

REVIEW

12 45

3 6 9

TV PROG.

PLAYBACK (cont.)

Manual Tracking

Your video recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the TV PROG. buttons.

OVERRIDE AUTOMATIC TRACKING

Press SP/LP ( ) on the remote to engage manual tracking.

ADJUST TRACKING MANUALLY

Press TV PROG. + or – to adjust tracking.

RETURN TO AUTOMATIC TRACKING

Press SP/LP ( ) on the remote to re-engage automatic tracking.

PUSH JOG

REW

NOTE:

When a new tape is inserted, the recorder enters the automatic tracking mode automatically.

3R Picture

3R(= Resolution and Response Recovery technology) maximises sense of resolution and sharpens image edges to make playback picture look better focused.

ACTIVATE 3R PICTURE

Press 3R PICTURE. The button will light.

● To turn off 3R Picture, press 3R PICTURE again so

Information On Colour System

You can also record SECAM signals, or play back a MESECAM tape on this recorder. When a MESECAM tape is played back, "MESECAM" appears on the screen for about 5 seconds. MESECAM is the designation for tapes with SECAM signals that have been recorded on a MESECAM-compatible PAL video recorder.

that the light goes off.

● Normally it is recommendable to keep 3R Picture ON (with the button lit).

● Depending on the type of tape used, picture quality may be better with 3R Picture set to off.

● If you use this recorder as the player for editing, be sure to turn off 3R Picture before starting.

● The setting will remain effective even though you turn on/off the recorder.

EN 15

Index Search

Your recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction.

NOTE:

Before starting, make sure the recorder is in the Stop mode.

ACTIVATE INDEX SEARCH

Press PUSH JOG or (™ or £). “™ 1” or “£ 1” is displayed on screen and search begins in

the corresponding direction.

● To access index codes 2 through 9, press PUSH JOG

ﬁ

or repeatedly until the correct index number is displayed. Ex.: To locate the beginning of B from the current

position, press PUSH JOG twice. To locate the beginning of D from the current position, press PUSH JOG once.

ﬁ

Current position

AB C D E F

–2 –1 1 2 3

£ 2

NTSC Playback

Your video recorder is equipped with NTSC circuitry that can play back NTSC tapes.

LOAD A CASSETTE

Insert a cassette recorded in NTSC.

START PLAYBACK

Press PLAY.

● "NTSC" appears on the screen for about 5 seconds.

● Some TVs shrink the picture vertically and place black bars at the top and bottom of the screen. This is not a malfunction on the part of either the video recorder or the TV.

● The picture may roll up and down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.)

● The counter and tape remaining time readings will be incorrect.

● During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour.

● Depending on the type of TV, the top and bottom portions of superimposed displays may be cut off during NTSC playback.

Index number

● When the specified index code is located, playback begins automatically.

Instant ReView

Simply by pressing a single button, the recorder power comes on, rewinds, and begins playback of the last timer-recorded programme. If you have several programmes recorded, you can easily access any of them.

NOTE:

Before starting, make sure that the recorder is off and that the Timer mode is disengaged.

ACTIVATE INSTANT REVIEW

Press REVIEW. The recorder power comes on and the recorder searches for the index code indicating the start

of the last timer-recorded programme. Once it’s found, playback begins automatically. The front display panel tells you how many programmes have been recorded. If you have, for example, 3 programmes, “REVIEW” and "3" appear and blink. To watch the first of the 3 programmes, press REVIEW three times. The recorder searches and begins playback automatically. You can access a programme as far as 9 index codes away from the current tape position.

Tape Position Indicator

The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of “5” in relation to “0” (beginning) or “+” (end) shows you where you are on the tape.

”O.S.D.” ( set to “ON”, or the indicator will not appear.

Z pg. 24) must be

Beginning End

NOTE:

Depending on the type of tape used, there may be times when the indication is not correct.

1:23:45

REMAIN 2:35

+++

NOTE:

Instant ReView is not possible while the recorder is in the Timer mode.

16 EN

REW

TIME SCAN SHUTTLE

SPATIALIZER

PLAYBACK (cont.)

A/B CODE

C.RESET

AUDIO MONITOR

REW

STOP

C. MEMORY

12 45

3 6 9

STOP

Spatializer

This feature expands sound field when you play back any stereo source or view a stereo programme while recording it. *SpatializerW has no effect on recording quality.

ACTIVATE SPATIALIZER

Press SPATIALIZER; the current setting will be displayed on the screen for about 5 seconds. Pressing

SPATIALIZER while the screen shows the display

changes the setting.

● To view a stereo programme such as movies or music, select "SPATIALIZER " to create more spacious sound.

● To view a monaural programme, select "SPATIALIZER[ST" which simulates a stereo effect.

● Select "SPATIALIZER OFF" to turn off SpatializerW if the sound becomes unnatural with either "SPATIALIZER " or "SPATIALIZER[ST" selected.

● If your TV is equipped with 3D-PHONIC and if you use both SpatializerW and 3D-PHONIC at the same time, the sound may become unnatural; set either function to "OFF".

● The setting will remain effective even though you turn on/off the recorder.

NOTES:

●

SpatializerWis effective only with a stereo TV.

●

The setting cannot be changed during search, still, frame-by-

frame playback or slow motion mode.

●

When this recorder is used as the player for editing, the

recorded audio will correspond to the SpatializerW setting.

SCENE FINDER

Soundtrack Selection

Y our video recorder is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select.

During Playback

Pressing AUDIO MONITOR on the remote control changes the soundtrack being played back as follows:

TRACK

Recorder's Front Panel On-Screen Display

L + R

L R

NORM NORM For audio-dubbed tapes

L + R + NORM

HI FI

NORM

USE

For Hi-Fi stereo tapes For main audio of Bilingual tapes For sub audio of Bilingual tapes

For audio-dubbed tapes

NOTES:

●

"L + R" should normally be selected. In this mode, Hi-Fi stereo tapes are played back in stereo, and the normal audio track is played back automatically for tapes with only normal audio.

●

For instructions on recording stereo and bilingual programmes, refer to page 26.

●

"O.S.D." must be set to "ON" or the on-screen displays will not appear (Z pg. 24).

EN 17

Scene Finder

This function helps you check contents of unlabeled recorded tapes at the touch of a single button.

Search Search Search

FF REW FF REW FF REW

5 seconds 5 seconds

on counter

5 seconds10 minutes

10 minutes on counter

NOTE:

Scene Finder cannot be used when the recorder is in the Record mode.

ACTIVATE SCENE FINDER

Press SCENE FINDER. The recorder starts forward search for 5 seconds and then fast-forwards 10 minutes

on the counter. This cycle is repeated until the end of the tape is reached.

● To start Scene Finder in the reverse direction, press SCENE FINDER and then press the REW button within 2 seconds. This cycle is repeated until the beginning of the tape.

● During Scene Finder, the following indications appear on the display panel:

STOP SCENE FINDER

Press STOP.

NOTES:

●

During Scene Finder search, you can also hear the tape sound. During fast forward or rewind, you hear the current TV sound instead.

●

During Scene Finder, the sound can be heard regardless of "TIME SCAN AUDIO" setting. Z pg. 20.

●

Scene Finder does not function during Index Search.

Next Function Memory

You can set your recorder's power to go off automatically after the tape is fully rewound. Before starting, make sure the recorder is in the Stop mode. For Automatic Power Off After Tape Rewind . . . . . . press REW, then press within 2 seconds.

NOTE:

If you want the power to be turned off automatically when the counter reads “0:00:00” (instead of at the beginning of the tape), press C.MEMORY so that the “M” mark appears before pressing REW.

Remote A/B Code Switching

The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control’s A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals. You can easily modify your video recorder to respond to B code signals.

REMOVE POWER SUPPLY

Unplug the mains power cord from the mains outlet.

SET A/B CODE SWITCH

Set to B.

RE-SUPPLY POWER

Plug the mains power cord back into the mains outlet.

TURN THE RECORDER ON

Press on the remote control. The recorder will now only respond to B code signals.

NOTE:

Some TV sets may malfunction in response to the B mode. If this happens, switch back to the A mode.

Counter Memory

Returns to the counter reading of “0:00:00” to conveniently find a specific place on the tape automatically.

SET COUNTER MEMORY

Press C. RESET during playback at a point you wish to locate later. The counter reads “0:00:00”. Then press

C.MEMORY, and “M” appears in front of the counter

digits.

ACTIVATE COUNTER MEMORY

When you wish to return to the designated point, press

STOP and then REW or FF.

● The tape rewinds or fast-forwards and stops at about 0:00:00 automatically.

● To cancel Counter Memory, press C.MEMORY again.

18 EN

PLAY

TIME SCAN SHUTTLE

PLAY

TimeScan

TIME SCAN INDICATOR

PLAYBACK (cont.)

Your recorder is equipped with the TimeScan function. TimeScan allows noise free pictures to be displayed on your TV screen in the forward and reverse search modes. Audio will be played back at normal speed during any of the TimeScan modes (Z pg. 19). TimeScan allows you to view a program in search mode while listening to the audio.

NOTES:

●

"TIME SCAN AUDIO" must be set to "ON", or the sound will not be heard in TimeScan mode. (Z pg. 19)

●

The audio will not synchronize with the video in TimeScan modes.

●

In Pause mode 3 seconds (approx.) of audio will be played

back repeatedly . (Z pg. 13)

●

In TimeScan search modes some of the audio information will not be played so that the audio can keep up with the video.

Audio signal during TimeScan

12 45

3 6 9

Playback tape

Sound of 1, 3 and 5 is heard. Sound of 2 and 4 is not heard. Output audio signal is normal (monaural) sound.

2345

Variable-Speed Search/ Reverse Play

ACTIVATE VARIABLE-SPEED SEARCH

During playback or still, turn the recorder's TIME SCAN SHUTTLE ring. It remains at that position even after you

release it. Each time it passes a click position, the playback speed changes. (Refer to the chart on pg 19 for playback speeds).

During playback, press PUSH JOG or .

● The more times you press, the faster the playback picture moves.

● To decrease speed, press the button for the opposite direction. (Refer to the chart on pg 19 for playback speeds).

To resume normal playback, press PLA Y.

PUSH JOG

+ 42 hidden pages