JVC HAW600RF User Manual
FM CORDLESS HEADPHONES
CASQUE FM SANS FIL
ENGLISHESPAÑOL
AURICULARES INALÁMBRICOS FM
HA-W600RF-J/C
For customer Use:
Enter below the Model No. and
Serial No. which are located on the
top or bottom of the cabinet. Retain
this information for future reference.
Model No.
Serial No.
FRANÇAIS
INSTRUCTIONS
MANUEL D’INSTRUCTIONS
MANUAL DE INSTRUCCIONES
LNT0066-001A
Warnings, cautions and others
Mises en garde, precautions et indications diverses
Avisos, precauciones y otras notas
FCC INFORMATION
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference
(2) This device must accept any
interference received, including
interference that may cause undesired
operation.
CAUTION: Changes or modifications
not approved by JVC could void user’s
authority to operate the equipment.
Contact
Address: JVC AMERICAS CORP.
JVC COMPANY OF AMERICA
1700 Valley Road, Wayne, N.J.
07470
Telephone: 1 (800) 252-5722
G-1
Note: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, it may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
IC INFORMATION
This device complies with RSS-210 of
the IC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference
(2) This device must accept any
interference received, including
interference that may cause
undesired operation of the device.
CAUTION: Changes or modifications
not approved by JVC could void user’s
authority to operate the equipment.
Contact
Address: JVC CANADA INC.
21 Finchdene Square,
Toronto, ON M1X 1A7
Telephone: (416) 293-1311
e-mail: info@jvc.ca
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Industry Canada’s
RSS-210. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
it may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
INFORMATION SUR IC
Cet appareil est conforme à la RSS-210 du
réglement de la IC. Le fonctionnement est
sujet aux deux conditions suivantes:
(1) Cet appareil ne peut causer
d’interférences nuisi-bles
(2) Cet appareil reçoit toute interférence
même les interférences qui peuvent
occasioner un mauvais fonctionnement.
ATTENTION: Les changements ou les
modifications non approuvés par JVC
risquent de retirer à l’utilisateur le droit
d’utiliser l’appareil.
Contact
Adresse: JVC CANADA INC.
21 Finchdene Square, Toronto,
ON M1X 1A7
Téléphone: (416) 293-1311
e-mail: info@jvc.ca
Remarque: L’appareil a été testé et jugé
conforme aux limites des appareils numériques
de classe B, aux termes de la réglementation
RSS-210 de l’industrie du Canada. Ces
limites ont pour but d’assurer une protection
raisonnable contre les interférences parasites
lorsque l’appareil est utilisé dans une installation
résidentielle. Cet appareil engendre, utilise et
peut émettre une énergie radioélectrique et, s’il
n’est pas installé et utilisé en stricte conformité
avec ces instructions, il peut provoquer des
interférences parasites dans les liaisons
radiophoniques. Ceci ne garantit pas pour
autant qu’une installation particulière n’émettra
aucune interférence. Si l’appareil engendre
des interférences parasites avec la réception
radio ou télévision, ce qui pourra être déterminé
en éteignant puis en rallumant l’appareil, il est
conseillé à l’utilisateur d’essayer de corriger
les interférences en prenant l’une des mesures
ci-dessous:
• Modifier l’orientation ou changer
l’emplacement de l’antenne de réception.
• Eloigner davantage l’appareil du récepteur.
• Brancher l’appareil dans une prise d’un circuit
différent de celui auquel le récepteur est
raccordé.
• Demander l’aide de son agent ou d’un
technicien radio/télévision qualifié.
G-2
IMPORTANT
CAUTION:
TO PREVENT ELECTRIC SHOCK
DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE
OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
ATTENTION:
POUR PREVENIR LES CHOCS
ELECTRIQES NE PAS UTILISER
CETTER FICHE AVEC UN
PROLONGATEUR, UNE PRISE DE
COURANT OU UNE AUTRE SORTIE
DE COURANT, SAUF SI LES LAMES
PEUVENT ETRE INSEREES A FOND
SANS EN LAISSER AUCUNE PARTIE A
DECOUVERT.
(1) This device may not cause
interference.
(2) This device must accept any
interference, including interference
that may cause undesired operation
of the device.
(1) Ce produit ne cause pas
d’interférence.
(2) Ce produit doit accepte toute
interférence, incluant interférence
qui peut causé opération non désiré.
ENGLISH
This product’s performance would be
degraded under a strong electro-static
environment. And the function would be
self-recoverable after the above case.
This product’s performance would be
degraded since the disturbance from the
mains cord. And the function would be selfrecoverable after the above case.
FRANÇAIS
Les performances de ce produit se
détérioreront dans un environnement
fortement électro-statique. Par ailleurs, le
fonctionnement se restaurera de lui-même
dans le cas ci-dessus.
Les performances de ce produit se
détérioreront en cas de perturbations
du cordon d’alimentation. Par ailleurs, le
fonctionnement se restaurera de lui-même
dans le cas ci-dessus.
ESPAÑOL
El rendimiento de este producto puede
deteriorarse en un entorno con campos
electrostáticos fuertes. El funcionamiento se
repondrá a la normalidad después del caso
arriba mencionado.
El rendimiento de este producto puede
deteriorarse debido a las perturbaciones del
cable de la red eléctrica. El funcionamiento
se repondrá a la normalidad después del
caso arriba mencionado.
Hearing Comfort and Well-Being
• Do not play your personal audio at a high volume. Hearing experts advice against
continuous extended play.
• If you experience a ringing in your ears, reduce volume or discontinue use.
Traffic safety
• Do not use while operating a motorized vehicle. It may create a traffic hazard and is
illegal in many area.
• You should use extreme caution or temporarily discontinue use in potentially
hazardous situations.
• Even though your headphones are of the open-air type designed to let you hear
outside sounds, don’t turn up the volume so high that you can’t hear what’s around
you.
G-3
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete
understanding and to obtain the best possible performance from the unit.
FEATURES
• Call Function–Call headphone user with
“CALL” button on base station (transmitter)
• Reception range up to 50 m/164 ft. (using
JVC measurement system)
• Auto Tuning–Headphones automatically
tunes in to the base station (transmitter) as it
turns on
• On Stand Charging–Rechargeable system
with the exclusive Ni-MH battery that
requires no charge cable
• Auto Power On/Off transmitter
• “PLL” Stabilized Transmission Technology
• Auto-level control circuit that automatically
adjusts signals to the appropriate modulation
level
• Large 40 mm (1.63˝) dia. driver unit for high
quality sound
• Adaptable to any audio/visual equipment
which has the analog audio output.
Contents
Precautions .......................................2
Parts identification ...........................3
Connection ........................................4
Battery installation ..........................5
Charging the battery ........................6
Basic operations ...............................7
Troubleshooting ...............................9
Specifications .................................10
ENGLISH
For your health and traffic safety
• Be careful not to turn the sound volume up too high when using the headphones. Your
hearing can be damaged by listening to sounds at excessive volume for long periods.
• Never use the headphones when driving a car, motorcycle, or bicycle. This could result in an
accident.
• Pay close attention to traffic around you when using the headphones while walking. Not
doing so could result in an accident.
1
Precautions
Important cautions
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
ENGLISH
1. Do not remove screws, cover or cabinet.
2. Do not expose this appliance to rain or
moisture.
Precautions
Installation
• Select a place which is level, dry and neither
too hot nor too cold (between 0°C and 35°C
(32°F and 95°F)).
• Keep away from direct sunlight.
• Do not put it too close to a heater.
• Indoor use only.
Power cord
• Do not handle the power cord with wet
hands!
• Do not bend the power cord sharply.
• Do not connect the supplied AC adaptor to
any other equipment. It is exclusively for use
with this unit.
Malfunctions, etc.
• There are no serviceable parts inside. If
anything goes wrong, unplug the power cord
and consult your dealer.
• Do not insert any metallic object.
• Do not allow water to get inside.
• Do not move or bend the ear cups or any
other part of the headphones with excessive
force. It may damage the headphones.
• Stop using the headphones if they are
causing discomfort on your skin. Otherwise
inflammation or irritation may be caused on
your skin.
• The ear pad will wear out earlier than the
other parts even in normal use or in normal
keeping due to the material characteristics.
For replacement of the ear pads, please
consult with the dealer where you purchased
the headphones.
• If the headphone is not used for a prolonged
time, unplug the AC adaptor from an AC
outlet.
Battery precautions
• Be sure to use the supplied exclusive battery.
Do not use any other rechargeable or dry cell
battery.
• Use only the type of battery the manufacturer
recommends when replacing the battery.
• Do not throw the battery in a fire or heat it.
• Do not immerse or wet the battery in water.
• Do not remove or damage the covering tube.
• Do not subject the battery to strong shocks or
throw it.
• If any liquid from the battery gets into your
eyes, it may cause blindness.
If battery liquid does get into your eyes, do
not rub them, but instead immediately wash
them thoroughly with clean water, then
consult a doctor at once.
Also, should any liquid from the rechargeable
battery get onto your skin or clothes, it may
burn your skin. In this case, wash with clean
water immediately.
• When discarding batteries, environmental
problems must be considered and the local
rules or laws governing the disposal of these
batteries must be followed strictly.
Charging precautions
• Charge only with supplied Ni-MH type
battery. Other types of battery may burst
causing personal injury and damage.
• Use only the supplied base station to charge
the battery.
• Be sure to use the supplied AC adaptor.
Supplied accessories
Check to be sure you have all of the supplied
accessories.
The number in parentheses is the quantity of the
pieces supplied. If anything is missing, contact
your dealer immediately.
• Exclusive rechargeable batteries (2)
• Exclusive AC adaptor (1)
• Connection cord (1)
• Conversion cord (1)
• Plug adaptor (1)
2
Parts identification
See pages in parentheses for details.
Base station (transmitter and battery charging unit)
1 23 4 5
1 CHARGE indicator (6)
2 Microphone (8)
3 CALL button (8)
4 POWER indicator (7)
Headphones
Left
1 AUTO SCAN button (7, 8)
2 AUTO SCAN indicator (7)
3 VOL (volume) (7)
4 Ear pad (5)
5 Battery charging terminal (6)
6 POWER button (6, 7)
7 POWER indicator (6, 7)
Back side
7
6
8
* The battery charging terminal on the base
station is covered with the protection cap
when purchasing.
Take off the cap before charging.
5 Battery charging terminal (6)
6 CHANNEL selector (8)
7 AUDIO IN jack (4)
8 DC IN
jack (4)
Right
ENGLISH
1
23
4 4 5
6
7
3
Connection
Be sure to connect the AC adaptor after all other
ENGLISH
1 Connect the base
station to the AV
equipment.
2 Connect the AC
adaptor to the base
station.
3 Connect the AC
adaptor to the AC
outlet.
connections are complete.
2
1
1
TV, audio amplifier, VCR,
DVD player, PC, etc.
Conversion cord for
stereo pin jack
(supplied)
Plug adaptor for 6.3 mm (0.24˝)
Phono jack (supplied)
Connection cord
(supplied)
AC adaptor
(supplied)
AV
equipment
Plug adaptor for monaural mini
jack (not supplied)
To stereo mini jack
3
To AC outlet
(AC 120 V, 60 Hz)
Note:
Do not use any other AC adaptor than the supplied AC adaptor. Otherwise, malfunctions may be
caused.
4
Battery installation
1 Take off the ear pad of the right
headphone.
2 Take off the battery covers.
3 Install the batteries.
Match the polarity (+ and –) on the batteries
with the + and – marking on the battery
compartments.
• Insert the – terminal of the battery at
first.
4 Put on the battery covers.
5 Put on the ear pad.
1 Insert the hem of the ear pad into the slit
on the headphone.
2 Turn the ear pad anticlockwise to slide
all the hem into the groove on the
headphone.
ENGLISH
Be sure to use the supplied exclusive
battery. Do not use any other
rechargeable or dry cell battery, which
may cause malfunctions or damage
the unit.
• Be sure that all the hem is inserted fully.
If not, turn the ear pad anticlockwise
again until all the hem slides in.
5
Charging the battery
The base station works as the battery charging
unit. Charge the rechargeable battery before
starting to use the headphones.
You can continuously use the headphones for
ENGLISH
about 10 hours after full battery charge.
1 Make sure that the headphones are
turned off.
You cannot charge the battery of the
headphones when the headphones
are turned on. Press POWER to turn
the Power indicator off.
2 Put on the headphones on the
base station so that their charging
terminals contact firmly.
• The battery charging terminal on
the base station is covered with the
protection cap when purchasing.
Take off the cap before charging.
• When putting the headphones on the
base station, hold them and adjust their
position with your both hands to assure
the contact of the terminals.
3 Confirm the CHARGE indicator
lights up.
If the charge indicator does not light up,
return steps 1 and 2 after checking the
connection of the AC adaptor.
• It takes about 30 hours to charge the
batteries fully.
• 30-hour charging may not charge the
battery fully depending on the battery or
other conditions.
• The cycle life of the rechargeable battery
is approximately 500 times. (It varies
depending on the conditions when
charging.)
• The battery leaks its charge little by little
even when the headphones’ power is off,
due to its characteristics.
Notes on the battery and charging
• To make battery life longer:
– charging the battery within the
temperature range of 10ºC – 35ºC (50ºF
– 95ºF).
– not using the headphones in excessively
cold places. Low temperature decreases
battery life.
– charging the battery after its complete
discharging. Charging before complete
discharge makes the battery life
gradually shorter.
• Replace the batteries when their lives
become about half or the playback sound
become constantly noisy.
Use the exclusive rechargeable Ni-MH
battery J47958 only. When purchasing
the battery, consult the dealer where you
bought the product.
• Replace two batteries at the same time
when replacing.
6
Basic operations
Listening to the sound from the base
station
The base station works as the FM transmitter
and send sound to the headphones.
Precaution
Turn down the volume of the headphones with
the VOL dial before turning on its power to
avoid excessive volume.
1 Start playback on the AV
equipment connected with the
base station.
The base station turns on automatically and
starts to transmit FM signals (Auto Power
On function).
The POWER indicator of the base station
lights up.
• In some situations, the power may not
be turned on automatically by the input
sound (e. g. a song with a quiet opening
or fade in). This is not a malfunction.
2 Press POWER on the
headphones to turn on the
power.
The POWER indicator lights up and the
headphones automatically starts to tune in
to the signal from the base station (Auto
Tuning function).
The AUTO SCAN indicator lights up when
tuned in.
• Press the center of the button firmly
when pressing POWER. Pressing the
edge may not turn on the power.
• Charge the battery in the following cases.
The battery ran out:
– The POWER indicator does not light
up after pressing POWER.
– The AUTO SCAN indicator does not
light up though the POWER indicator
lights up.
• No sound is heard while Auto Tuning. It
takes a few seconds to tune in.
• Press AUTO SCAN when
the sound does not come out
properly.
3 Adjust the volumes of the
AV equipment and the
headphones.
• Adjust the volumes within the area about
7 m (23 ft.) from the base station to get
optimum signal reception.
• You can get better sound by setting the
volume of the AV equipment as high
as possible without causing distortion
and that of the headphone lower (except
when connecting the AV equipment
through LINE OUT jacks).
To Turn off the units
Press POWER on the headphones and
stop playback on the AV equipment.
The headphones’ POWER indicator
goes off.
• The base station automatically turns off if no
signals come in for about four minutes (Auto
Power OFF function).
• The white noise may come out when the base
station turns off. Take off and turns off the
headphones after using.
ENGLISH
7
Basic operations
Selecting a better reception channel
When the playback sound is noisy, you can
choose one of the other two channels to
ENGLISH
transmit signals on the base station.
• The white noise may come out when
switching the channel. Take off the
headphones when switching the channel.
1 Slide the CHANNEL
selector on the back side of
the base station to select another
channel.
2 Press AUTO SCAN on the
headphones to tune in to
the new channel.
3 Repeat Steps 1 and 2 to select the
best channel.
Listening area
The headphones can receive the FM signal of
the base station 50 m (164 ft.) away from it at
maximum (when no interference or obstacles
exist between them). But the receivable
range becomes shorter or reception quality
becomes poorer in the following cases:
– In places such as reinforced concrete
buildings
– Obstacles such as steel-reinforced doors
exist between the base station and
headphones
– Items such as metal furniture are situated
nearby
– In places facing a street
– Noise or interference sources exist nearby
(e.g. mobile ham, radio stations, high-
voltage power lines, a microwave oven,
cordless phones, cellular phones, etc.)
Call through the base station
You can call the one using the headphones with
the microphone on the base station.
1 Press and hold CALL
on the base station.
The playback sound is interrupted.
2 Speak to the microphone on the
base station.
Speak at least 10 cm (4 inches) away from
the microphone. The speaking sound may
be distorted.
3 Release CALL after finishing
speaking.
• Do not speak to the
microphone suddenly in
too loud voice. The sudden excessive
loud sound may damage the ears of
the headphones user or may cause an
accident to the user.
• Do not use the Call function when the
headphones are near the base station. It
may cause a howling sound and damage
the headphone user or cause an accident.
8
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service
center.
Symptom Cause/Remedy
No sound comes out at all. • Turns on the power of the headphones.
No sound comes out from
R-channel.
Sound is distorted. • The headphones’ battery will soon run out. Fully charge the
Sound is noisy. • The headphones’ battery will soon run out. Fully charge the
• Start playback on the AV equipment connected to the base
station.
• Check the connection between the base station and the AV
equipment.
• Turns up the volume of the headphones or the connected AV
equipment to an appropriate level.
• Fully charge the headphones’ battery.
• Check the connection between the base station and the AV
equipment.
• Sound comes out only of L-channel when the base station is
connected to the monaural audio output. Convert the mini
plug to the base station from stereo to monaural with the plug
adaptor (not supplied).
battery.
• The volume of the headphones and/or the connected AV
equipment is too high. Adjust their volume to an appropriate
level.
battery.
• Switch the base station channel to another and press AUTO
SCAN on the headphones.
• The volume of the connected AV equipment is too low. Adjust
the volume as high as possible without causing distortion.
• Too far from the base station. Use the headphones within the
range of the base station (see page 8).
ENGLISH
Cannot charge the battery. • Check the contact of the charging terminals on the base station
and the headphones.
• Check the polarity of the battery.
• The cycle life of the battery ended. Replace with the new
battery (see page 6).
9
Specifications
General Specifications
Modulation system: Stereo frequency
Carrier frequency: 912.0 MHz (Channel 1)
ENGLISH
Usable area
(distance to reach): Max. 50 m (164 ft.)
(using JVC
Frequency response: 25 Hz – 13,000 Hz
Distortion: Less than 3% (at 1 kHz)
Transmitter (J22320-001)
Power requirements: DC 12 V (with the
Audio input terminals: 3.5 mm (0.13˝) dia.
Input impedance: 36 kΩ
Reference input level: 350 mV
Dimensions: 159 (W) mm x 114 (D)
Mass: 280 g (9.9 oz)
modulation system
912.5 MHz (Channel 2)
913.0 MHz (Channel 3)
measurement systems,
under controlled
ambient conditions)
exclusive AC adaptor)
stereo mini jack
mm x 123 (H) mm
(6.26˝ x 4.49˝ x 4.84˝)
(without connection
cord and AC adaptor)
Headphones
Power requirements: Rechargeable Ni-MH
battery (1.2 V) x 2
Battery running time: 10 hours (when charged
for 30 hours)
Mass: 250 g (8.8 oz)
(with rechargeable
battery)
Supplied Accessories
• Instructions x 1
• Exclusive AC adaptor x 1
(J34675-001: AC 120 V, 60 Hz, 4 W)
• Exclusive rechargeable Ni-MH battery x 2
• Connection cord x 1
(3.5 mm (0.13˝) dia. stereo mini plug: 2.2 m
(7.22 ft))
• Conversion cord x 1
(3.5 mm (0.13˝) dia. stereo mini jack — RCA
pin plug x 2: 0.1 m (0.33 ft))
• Plug adaptor x 1
(converts 3.5 mm (0.13˝) dia. stereo mini
plug to a 6.3 mm (0.24˝) dia. standard stereo
phone plug)
10
* Design and specifications subject to change without notice.
HA-W600RF-J/C
FM CORDLESS HEADPHONES
© 2006 Victor Company of Japan, Limited
Printed in China
LNT0066-001A
Loading...