JVC GR-FXM25 User Manual

COMPACT VHS CAMCORDER
GR-FXM35 GR-FXM25
ENGLISH
INSTRUCTIONS
LYT0328-001A
EN
2 EN
Dear Customer,
Using This Instruction Manual
• All major sections and subsections are listed in the Table Of Contents (
• Notes appear after most subsections. Be sure to read these as well.
• Basic and advanced features/operation are separated for easier reference.
It is recommended that you . . .
.... refer to the Index (
.... read thoroughly the Safety Precautions. They contain extremely important information regarding the safe
use of this product.
You are recommended to carefully read the cautions on pages 55 and 56 before use.
Z pgs. 52 – 54) and familiarize yourself with button locations, etc. before use.
SAFETY PRECAUTIONS
Z pg. 3).
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
Warning on lithium cell battery (for clock operation and remote control unit)
The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100°C or incinerate. Replace the battery with Maxell, Panasonic (Matsushita Electric), Sanyo or Sony CR2025; use of another battery may present a risk of fire or explosion.
n Dispose of used battery promptly. n Keep away from children. n Do not disassemble and do not dispose of in
fire.
CAUTIONS:
n If you notice smoke or a peculiar smell coming
from the camcorder or AC adapter/charger, shut it down and unplug it immediately. Continue using the camcorder or AC adapter/ charger under these conditions could lead to fire or electric shock. Contact your JVC dealer. Do not attempt to repair the malfunction yourself.
n To prevent shock, do not open the cabinet. No
user serviceable parts inside. Refer servicing to qualified personnel.
n When you are not using the AC Power
Adapter/Charger for a long period of time, it is recommended that you disconnect the power cord from AC outlet.
NOTES:
The rating plate (serial number plate) and safety caution are on the bottom and/or the back of the main unit.
The rating plate (serial number plate) of the AC Power Adapter/Charger is on its bottom.
This camcorder is designed to be used with PAL­type colour television signals. It cannot be used for playback with a television of a different standard. However, live recording and LCD monitor/viewfinder playback are possible anywhere. Use the BN-V12U/V20U battery packs and, to recharge them, the provided multi­voltage AC Power Adapter/Charger. (An appropriate conversion adapter may be necessary to accommodate different designs of AC outlets in different countries.)
This unit is produced to comply with Standard IEC Publ. 65.
n Camcorder is designed exclusively for the
VHS-C video cassette. Only cassettes marked VHS-C can be used with this unit.
n HQ VHS is compatible with existing VHS
equipment.
MAJOR FEATURES
CONTENTS
EN3
EN3
n Programme AE with Special Effects
(Z pg. 22 – 23)
•Electronic Fog Filter
•ND Effect
•Sepia
•Twilight
•Sports
•Nega/Posi
•1/2000 sec. High Speed Shutter
n LCD Colour Monitor ( n Snapshot (GR-FXM35 only) ( n 5-Sec. Recording (GR-FXM25 only)
(
Z pg. 18)
n Menu Adjustment ( n Picture Stabilizer ( n Digital Hyper Zoom ( n Integrated Auto Light
(GR-FXM35 only) (
Z pg. 14)
Z pg. 20)
Z pg. 26, 27, 28)
Z pg. 18)
Z pg. 16)
Z pg. 19)
PROVIDED ACCESSORIES
•AC Power Adapter/ Charger AA-V15EG
•Battery Pack BN-V12U
•Shoulder Strap
•Cassette Adapter C-P7U
•Remote Control RM-V700U (GR-FXM35 only)
•Editing Cable (GR-FXM35 only)
GETTING STARTED
4 – 11
Power ............................................ 4
Clock (Lithium) Battery Insertion/
Removal ........................................ 6
Date/Time Settings............................. 7
Recording Mode Setting ....................... 8
Tape Length Setting............................. 8
Loading/Unloading A Cassette ............... 9
Grip Adjustment ............................... 10
Viewfinder Adjustment ...................... 10
Shoulder Strap Attachment ..................11
Tripod Mounting ...............................11
RECORDING
12 – 35
Basic Recording................................12
Basic Features ................................. 16
Advanced Features............................ 20
PLAYBACK
36 – 41
Basic Playback................................. 36
Features ........................................37
Using The Cassette Adapter .................39
Basic Connections And Tape Dubbing ....... 40
USING THE REMOTE CONTROL UNIT
Random Assemble Editing ................... 44
Insert Editing .................................. 48
Audio Dubbing .................................49
TROUBLESHOOTING INDEX
Controls, Connectors And Indicators ....... 52
Indications ..................................... 54
CAUTIONS
42– 49
50 – 51
52 – 54
55 – 56
SPECIFICATIONS
57
•Audio/Video (A/V) cable
• Lithium Battery CR2025
• x1 for GR-FXM25 (clock operation)
• x2 for GR-FXM35 (clock operation and remote control)
• DC Cord
OPTIONAL ACCESSORIES
57
4 EN
Marks
CHARGE indicator
REFRESH switch
REFRESH indicator
REFRESH
The AC Power Adapter/Charger features a REFRESH function that allows you to fully discharge the battery pack before recharg­ing. Perform the REFRESH function after no less than 5 chargings.
To discharge the battery . . .
.... attach the battery pack to the adapter as
shown in the above illustration. Then push REFRESH. The REFRESH indicator lights when discharging starts, and goes out when discharging is complete.
To AC outlet
GETTING STARTED
Power
This camcorder’s 3-way power supply system lets you choose the most appropriate source of power.
NOTES:
No function is available without power supply.
Use only the specified power supply.
Do not use provided power supply units with other equipment.
CHARGING THE BATTERY PACK
SUPPLY POWER
1
Connect the charger’s AC power cord to a wall outlet.
ATTACH BATTERY PACK
2
Align the marks and slide the battery pack in the direction of the arrow until it locks in place.
•The CHARGE indicator begins blinking to indicate charging has started.
DETACH BATTERY PACK
3
When the CHARGE indicator stops blinking but stays lit, charging is finished. Slide the battery pack opposite the direction of the arrow.
Battery pack Charging time Discharging time
BN-V12U approx. 1 hr. 10 min. approx. 3 hrs. 30 min. BN-V20U approx. 1 hr. 50 min approx. 6 hrs. 40 min.
Hook on.
A
Push in.
B
BATTERY RELEASE
ATTENTION:
Before detaching the power source, make sure that the camcorder’s power is turned off. Failure to do so can result in a camcorder malfunction.
USING THE BATTERY PACK
ATTACH BATTERY PACK
1
Hook its end to the camcorder ( ) and push the battery pack in until it locks in place (
DETACH BATTERY PACK
2
Slide BATTERY RELEASE and pull out the battery pack.
Approximate recording time (unit: min.)
Battery pack
BN-V12U 60 (35) 65 (40) 50 (35) BN-V20U 95 (60) 105 (65) 85 (55)
( ) : when the video light is on (GR-FXM35 only).
LCD LCD LCD monitor on/ monitor off/ monitor on/ Viewfinder off Viewfinder on Viewfinder on
) .
INFORMATION:
VU-V856KIT is a set composed of the BN-V856U battery pack and AA-V80EG AC Power Adapter/Charger. The BN-V856U battery pack provides approx. 7 hours of recording time when the viewfinder is on and the LCD monitor and the video light are off. Also read thoroughly the VU-V856KIT’s instruction manuals. It is impossible to charge the BN-V856U battery pack using the provided AC Power Adapter/Charger. Use the optional AA-V80EG AC Power Adapter/Charger.
EN5
Charge Marker
Charge marker
A charge marker is provided on the battery pack to help you remember whether it has been charged or not. Two colours are provided (red and black)—you choose which one means charged and which means discharged.
NOTES:
The recording time per charge is affected by such factors as the time spent in Record-Standby mode and the frequency of zooming. It is safer to have spare battery packs to cover 3 times the planned shooting time.
Charging times noted on page 4 are for a fully discharged battery pack, and discharging times are for a fully charged battery pack.
Charging and discharging times vary according to the ambient temperature and the status of the battery pack.
Remember to set the charge marker after charging a battery pack or after detaching a discharged one from your camcorder.
Perform the REFRESH function after no less than 5 chargings.
While the AC Power Adapter/Charger’s power cord is disconnected from the AC outlet, it is possible to discharge the battery by pressing the REFRESH switch. During that time, the AC Power Adapter/Charger does not charge the battery. When discharging is complete, detach the battery from the AC Power Adapter/ Charger to store it.
High temperatures can damage the battery pack, so use only where good ventilation is available. Do not allow it to discharge in a container, such as a bag.
If you stop recharging or discharging part way through, make sure to remove the battery pack before unplugging the adapter’s AC cord.
Remove the battery pack from the adapter immediately after discharging.
To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.
Make sure you unplug the DC cord before charging or discharging the battery pack.
The CHARGE indicator may not light properly with a brand new battery pack, or with one that has been stored for an extended period. In this case, remove and reattach the battery pack and recharge it. The CHARGE indicator should blink during recharging. If not, contact your nearest JVC dealer.
GETTING STARTED
To DC IN jack
DC OUT terminal
DC Cord
Car Battery Charger/Adapter BH-V3E (optional)
AC Power Adapter/Charger AA-V15EG
To AC outlet
To car’s cigarette lighter socket
USING AC POWER
Use the AC Power Adapter/Charger (connect as shown in the illustration).
NOTES:
The provided AC Power Adapter/Charger features automatic voltage selection in the AC range from 110 V to 240 V.
When using the DC cord, make sure you connect the end of the cord with the core filter to the camcorder. The core filter reduces interference.
USING A CAR BATTERY
Use the optional Car Battery Charger/Adapter (connect as shown in the illustration).
NOTES:
When using the car battery, leave the engine idling.
The optional Car Battery Charger/Adapter (BH-V3E) can also be used to charge the battery pack (except BN-V20U/V856U).
When using the optional Car Battery Charger/ Adapter, refer to the respective instruction booklet.
6 EN
Battery holder
Slot
GETTING STARTED
(cont.)
Clock (Lithium) Battery Insertion/Removal
This battery is necessary for clock operation and to perform date/time settings.
SWITCH OFF POWER
1
Switch off the unit’s power and remove the power supply unit (battery pack, AC Power Adapter/Battery Charger, etc.).
REMOVE BATTERY HOLDER
2
Pull out the battery holder.
INSERT BATTERY IN HOLDER
3
Insert the battery in the holder, and be sure to have the “+” mark visible.
RE-INSERT HOLDER
4
Slide the holder back into the slot until you hear a click.
NOTES:
See “SAFETY PRECAUTIONS” (Z pg. 2) for information on safe handling of lithium batteries.
To avoid losing the battery and/or battery holder, place the camcorder with the grip side up as shown in the illustration when inserting/removing the battery.
MENU Button
Select Dial
Display
4
NEXT M . W . B . D . ZOOM TELE MACRO
DATE TIME
TAPE LENGTH
4
RETURN
DATE TIME
YEAR
MONTH
DAY
TIME
EXIT
4
NEXT M . W . B . D . ZOOM TELE MACRO DATE TIME TAPE LENGTH
4
RETURN
AUTO ON OFF
T45
AUTO ON OFF
T45
1999
22 : 50
Power lamp
Power Switch
Menu Screen
DATE/TIME Menu
1 1
24-hour indication
EN7
Date/Time Settings
ACCESS MENU SCREEN
1
Set the Power Switch to “PRO.”, then press MENU.
•The power lamp comes on.
SELECT FUNCTION
2
Rotate the Select Dial to move the highlight bar to “DATE/TIME”, then press it. The DATE/TIME Menu appears.
•If you decide you want to return the date and time to the previous settings, rotate the Select Dial to move the highlight bar to “EXIT” and press it, then go to step 6.
•If you want to set only the time without changing the date, go to step 4.
SET DATE
3
Rotate the Select Dial to move the highlight bar to the item you want to set and then press it. When the setting begins blinking, rotate the Select Dial until the correct setting appears and then press it. The setting stops blinking.
•Repeat this procedure until you’re satisfied with the Date settings (“YEAR”, “MONTH” and “DAY”).
SET TIME
4
Rotate the Select Dial to move the highlight bar to “TIME” and then press it. When the hour setting begins blinking, rotate the Select Dial until the correct setting appears and then press it. When the hour setting stops blinking and the minute setting begins blinking, rotate the Select Dial until the correct setting appears and then press it. The minute setting stops blinking.
START CLOCK OPERATION
5
When none of these settings (YEAR, MONTH, DAY, TIME) blinks, rotate the Select Dial to move the highlight bar to “EXIT”, and press it. The Menu Screen reappears with the highlight bar on “RETURN”.
CLOSE MENU SCREEN
6
Press the Select Dial.
NOTE:
To display the date and time in the camcorder’s display and on a connected TV, see “Date/Time Insert” (Z pg. 24).
GETTING STARTED
8 EN
4
NEXT M . W . B . D . ZOOM TELE MACRO DATE TIME
TAPE LENGTH
4
RETURN
T30
T45
T60
MENU Button
SP/LP Recording Mode Button
Select Dial Power Switch
Viewfinder
Tape length indicator
AUTO ON OFF
T45
T45
Recording mode indicator
Menu Screen
TAPE LENGTH Setting Menu
SP
Display
TAPE LENGTH
GETTING STARTED
(cont.)
Recording Mode Setting
Set depending on your preference.
SET RECORDING MODE
1
First set the Power Switch to “AUTO” or “PRO.”. Press SP/LP for more than 1 second. “SP” (Standard Play) provides higher picture and sound quality and is better for dubbing, while “LP” (Long Play) is more economical, providing twice the recording time.
NOTE:
If the recording mode is switched during recording, the playback picture will be blurred at the switching point.
Tape Length Setting
Set the tape length according to the length of the tape used.
ACCESS MENU SCREEN
1
First set the Power Switch to “PRO.”. Press MENU.
SELECT FUNCTION
2
Rotate the Select Dial to move the highlight bar to “TAPE LENGTH”, then press it. The TAPE LENGTH Setting Menu appears.
SET TAPE LENGTH
3
Rotate the Select Dial to move the highlight bar to the correct setting. T30 = 30 minutes of recording time, T45 = 45 minutes, and T60 = 60 minutes.
•If you decide you want to return the tape length to the previous setting, rotate the Select Dial to move the highlight bar to “EXIT”.
CLOSE MENU SCREEN
4
Press the Select Dial. The Menu Screen reappears with the highlight bar on “RETURN”. Press the Select Dial again to close the Menu Screen.
NOTE:
The tape remaining time (Z pg. 13) displayed in the viewfinder is correct only if the correct tape length has been selected.
EXIT
4
NEXT M . W . B . D . ZOOM TELE MACRO DATE TIME TAPE LENGTH
4
RETURN
AUTO ON OFF
T60
Cassette holder
Erase Protection Gear
EJECT SwitchPUSH Button
Turn to take up slack.
EN9
Loading/Unloading A Cassette
OPEN LCD MONITOR
1
Open the LCD monitor to an angle of over 60 degrees.
OPEN CASSETTE HOLDER
2
Slide EJECT until the holder opens. Do not use force to open.
INSERT/REMOVE CASSETTE
3
Make sure the label is facing outward.
CLOSE CASSETTE HOLDER
4
Press PUSH and make sure the holder is closed and locked.
CLOSE LCD MONITOR
5
First make sure the holder is closed. Then close the LCD monitor.
NOTES:
Closing the LCD monitor while the cassette holder is still open may cause damage to the LCD monitor.
The cassette holder can’t be opened unless a power supply is attached.
Make sure that the tape is not slack when loading the cassette. If there is any slack, turn the gear on the cassette in the direction of the arrow to take up the slack.
Make sure the Erase Protection tab is in the position that allows recording. If not, slide the tab. Some cassettes have removable tabs. If the tab has been removed, cover the hole with adhesive tape.
The cassette holder cannot be opened while the camcorder is in the record mode.
GETTING STARTED
10 EN
Power Zoom Lever
Recording Start/Stop Button
33
22
180°180
°
GETTING STARTED
Grip Adjustment
EXPAND LOOP
1
Separate the Velcro strip.
INSERT HAND
2
Pass your right hand through the loop and grasp the grip.
ADJUST STRAP LENGTH
3
Adjust so your thumb and fingers can easily operate the Recording Start/Stop Button and Power Zoom Lever. Refasten the Velcro strip.
Viewfinder Adjustment
SELECT OPERATION MODE
1
Set the Power Switch to “CAMERA” (“AUTO” or “PRO.”).
POSITION VIEWFINDER
2
Adjust the viewfinder manually for best viewability (see illustration on left).
(cont.)
PAUSE
1
Set “POWER” to “CAMERA” (“AUTO” or “PRO.”)
ADJUST DIOPTRE
3
Turn the Dioptre Adjustment Control until the indications in the viewfinder are clearly focused.
2
4
3
1
EN11
Shoulder Strap Attachment
ATTACH STRAP
1
Following the illustration at left, thread the strap through the top of the eyelet 1, then fold it back and thread it through the buckle 2. Repeat the procedure to attach the other end of the strap to the other eyelet
3, making sure the strap is not twisted.
ADJUST LENGTH
2
Adjust as shown in the illustration at left 4.
Tripod Mounting
ALIGN AND TIGHTEN
1
Align the screw and camera direction stud on the tripod with the camera’s mounting socket and stud hole. Then tighten the screw.
CAUTION:
When using a tripod, be sure to open and extend its legs fully to stabilise the camcorder. To prevent damage to the unit caused by falling over, do not use a small-sized tripod.
GETTING STARTED
12 EN
EJECT Switch
Recording Start/Stop Button
LENS COVER Open/Close Ring
Power Switch
Power lamp
Tally lamp (lights while recording is in progress)
RECORDING
Basic Recording
NOTE:
You should already have performed the procedures listed below. If not, do so before continuing.
Power (Z pg. 4)
Recording Mode Setting (Z pg. 8)
Tape Length Setting (Z pg. 8)
Grip Adjustment (Z pg. 10)
Viewfinder Adjustment (Z pg. 10)
LOAD A CASSETTE
1
First open the LCD monitor to an angle of over 60 degrees. Slide EJECT to open the cassette holder, then insert the cassette with the label facing out. Press PUSH to ensure the holder is closed and locked.
Shooting While Watching The Viewfinder
ENTER RECORD-STANDBY MODE
2
Make sure the LCD monitor is closed and locked. Turn the LENS COVER Open/Close Ring to open the lens cover, then set the Power Switch to “CAMERA” (“AUTO” or “PRO.”).
•The power lamp lights and the camcorder enters the Record-Standby mode.
•The scene you are aimed at appears on the viewfinder screen, with the word “PAUSE” superimposed upon it.
START SHOOTING
3
Press the Recording Start/Stop Button.
•“ ” appears in the viewfinder while recording is in progress.
Power Switch Position
According to the Power Switch position you have selected, the following functions are available:
AUTO (Full Auto mode):
Allows you to record using NO special effects or manual adjustments. Suitable for standard recording.
Allows you to set various recording functions using the menus. If you want more creative capabilities than full auto recording, try this mode.
PRO. (PRO. mode):
POWER OFF:
Allows you to switch off the camcorder.
Tape remaining time indicator
25MIN
Recording Start/Stop Button
DISPLAY Button
MIN
(Now calculating)
120MIN
119MIN
3MIN
2MIN
(Blinking)
1MIN
(Blinking)
0MIN
(Blinking)
EN13
STOP RECORDING
4
Press the Recording Start/Stop Button again to stop recording.
•The camcorder re-enters the Record-Standby mode.
NOTES:
When the Power Switch is set to “CAMERA” and the LCD monitor is opened at an angle of 60 degrees or more, the LCD monitor switches on and the viewfinder switches off automatically to save power.
The cassette holder cannot be opened unless a power supply is attached.
There may be a delay after you slide EJECT until the holder opens. Do not use force.
The tape remaining time is only displayed in the viewfinder as shown.
The remaining time indicated in the viewfinder is approximate.
The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary according to the type of tape used.
The tape remaining time indicator is correct only if the correct tape length has been selected (Z pg. 8).
“TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this condition for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is loaded.
If the Record–Standby mode continues for 5 minutes without performing Zoom or any other operations, the camcorder’s power shuts off automatically. Set the Power Switch to “POWER OFF”, and then back to “CAMERA” to turn the camcorder on again.
If the Recording Start/Stop button is pressed after the Record-Standby mode has continued for over 5 minutes, recording may not start immediately.
If you are recording on a cassette from the middle (such as when a tape is removed and re-inserted during recording), use the Retake function (Z pg. 17) to find the end of the last recording so you don’t erase any of it.
The LENS COVER warning blinks for about 5 seconds when the camcorder is turned on with the cover closed.
While shooting, sound is not heard from the speaker.
To turn the tally lamp off during recording, refer to pgs. 26 and 28.
RECORDING
LCD Monitor/Viewfinder Indications
Press DISPLAY to make the following indications appear/ disappear from the camcorder’s display: cassette warning, tape remaining time, battery pack remaining power indicator and tape length indicator (
PRESS DISPLAY BUTTON
1
To turn off the indications, press DISPLAY for more than 1 second. Press again for more than 1 second to make the indications reappear.
NOTE:
Even if the indications are off, the tape remaining time appears blinking when the tape is near its end, and the battery pack remaining power indicator appears blinking when the power is almost gone.
Z pg. 54).
14 EN
180°
Recording Start/Stop Button
90°
LENS COVER Open/Close Ring
Power Switch
Power lamp
Tally lamp (lights while recording is in progress)
RECORDING
Basic Recording (cont.)
Shooting While Watching The LCD Monitor
Before the following steps, perform step 1 (Z pg. 12).
ENTER RECORD–STANDBY MODE
2
Make sure the LCD monitor is fully open. Turn the LENS COVER Open/Close Ring to open the lens cover, then set the Power Switch to “CAMERA” (“AUTO” or “PRO.”).
•The power lamp lights and the camcorder enters the Record-Standby mode.
•The scene you are aimed at appears in the LCD monitor, with the word “PAUSE” superimposed upon it.
START SHOOTING
3
Tilt the LCD monitor upward/downward for best viewability (Z pg. 15) and press the Recording Start/ Stop Button.
•“ ” appears in the LCD monitor while recording is in progress.
STOP RECORDING
4
Press the Recording Start/Stop Button again to stop recording.
•The camcorder re-enters the Record-Standby mode.
NOTES:
When you use the LCD monitor outdoors in direct sunlight, the LCD monitor may be difficult to see. If this happens, we recommend that you use the viewfinder (Z pg. 12).
To turn the tally lamp off during recording, refer to pgs. 26 and 28.
For other notes, refer to pg. 13.
EN15
Journalistic Shooting
In some situations different angles of shooting may be required for more dramatic results.
OPEN LCD MONITOR
1
Make sure the LCD monitor is fully open.
TILT LCD MONITOR
2
Tilt the LCD monitor in the most convenient direction.
•The LCD monitor can rotate almost full circle (270°: 90° downward, 180° upward).
Interface Shooting
The person you shoot can view himself/herself in the LCD monitor, and you can even shoot yourself while viewing your own image in the LCD monitor.
TILT LCD MONITOR UPWARD
1
Open the LCD monitor and tilt it upward to 180 degrees so that it faces forward.
•When the LCD monitor is tilted upward to an angle of over approx. 105 degrees, the monitor image is inverted vertically, and the viewfinder also switches on.
RECORDING
Self-recording
BRIGHT Dial
START RECORDING
2
Point the lens toward the subject (yourself when self­recording) and start recording.
•During Interface Shooting, the monitor image and indications do not appear inverted as they would when viewing a mirror.
NOTE:
The monitored image can be viewed on the LCD monitor and in the viewfinder.
Brightness Control
You can adjust the brightness of the LCD monitor by turning the BRIGHT Dial.
ADJUST BRIGHTNESS
1
If you want to brighten the image . . .
Turn the Dial towards “+”.
If you want to darken the image . . .
Turn the Dial towards “”.
16 EN
RECORDING
Basic Features
Zoom in
Display
Zoom indicator bar
1X
Zoom level indicator
Approximate zoom ratio
Power Zoom Lever
Zoom out
FEATURE:
Zooming
PURPOSE:
To produce the zoom in/out effect, or an instantaneous change in image magnification. Digital circuitry extends the maximum magnification offered by optical zoom. This system is called Digital Zoom.
OPERATION:
Zoom In Push the Power Zoom Lever towards “T”.
Zoom Out Push the Power Zoom Lever towards “W”.
n The quicker you push the Power Zoom Lever, the
quicker the zoom action.
NOTES:
Focusing may become unstable during Zooming. In this case, set the zoom while in Record–Standby, lock the focus by using the manual focus (Z pg. 31), then zoom in or out in Record mode.
The zoom level indicator (5) moves during zoom. Once the zoom level indicator reaches the top of the zoom indicator bar, all magnification from that point is through digital processing.
When using Digital Zoom, the quality of image may suffer. To deactivate Digital Zoom, set “D.ZOOM” to “OFF” in the Menu Screen (Z pg. 27).
Power Switch
EN17
RETAKE (R/F) Button
FEATURE:
Quick Review
PURPOSE:
To check the end of the last recording.
OPERATION:
1) Press “ ” and release quickly during the Record–
Standby mode.
n Tape is rewound for about 2 seconds and played
back automatically, then pauses in Record–Standby mode for the next shot.
NOTE:
Distortion may occur at the start of playback. This is normal.
FEATURE:
Retake
PURPOSE:
To re-record certain segments.
OPERATION:
1) Make sure the camcorder is in the Record–Standby
mode.
2) Press either RETAKE to reach the start point for new
recording. Pressing “F” forwards the tape and pressing “R” reverses it.
3) Press the Recording Start/Stop Button to start
recording.
NOTE:
Noise bars appear and pictures may become monochrome or darken during Retake. This is normal.
RECORDING
18 EN
5 SEC. REC Button
Display
PAUSE
5S
5 Sec. Rec mode indicator
Picture stabilizer indicator
P. STABILIZER Button
Power Switch
RECORDING
FEATURE:
Picture Stabilizer
Basic Features (cont.)
PURPOSE:
To compensate for unstable images caused by camera­shake, particularly at high magnification.
OPERATION:
1) Press P. STABILIZER. “ ”appears.
n To switch off the Picture Stabilizer, press
P. STABILIZER. The indicator disappears.
NOTES:
Accurate stabilisation may not be possible if hand shake is excessive, or under the following condi­tions:
When shooting subjects with vertical or horizontal stripes.
When shooting dark or dim subjects.
When shooting subjects with excessive backlighting.
When shooting scenes with movement in various directions.
When shooting scenes with low-contrast back­grounds.
Switch off the Picture Stabilizer when recording with the camcorder on a tripod.
The “ ” indicator appears blinking if the Stabilizer cannot be used.
FEATURE:
5Sec. Rec (5-sec. Recording) (GR-FXM25 only)
PURPOSE:
To record a scene for 5 seconds, providing quick scene transitions like those seen in TV programmes.
OPERATION:
1) During Record–Standby, press 5SEC. REC. “ 5S”
appears and 5Sec. Rec is reserved.
2) Press the Recording Start/Stop Button. Recording
starts, and after 5-second recording is finished, the camcorder reenters the Record–Standby mode automatically.
n To cancel the 5Sec. Rec. function, press 5SEC. REC
again so that “ 5S” disappears.
NOTE:
Fade/Wipe (Z pg. 21) cannot be activated by pressing 5SEC. REC.
EN19
LIGHT OFF/AUTO/ON Switch
DANGER
n The video light can become extremely
hot. Do not touch it either while in operation or soon after turning it off, otherwise serious injury may result.
n Do not place the camcorder into the
carrying case immediately after using the video light, since it remains extremely hot for some time.
n When operating, keep a distance of
about 30 cm. between the video light and people or objects.
n Do not use near flammable or explosive
materials.
n It is recommended that you consult your
nearest JVC dealer for replacing the video light.
FEATURE:
Video Light (GR-FXM35 only)
PURPOSE:
To brighten the scene when natural lighting is too dim.
OPERATION:
1) Set the LIGHT OFF/AUTO/ON Switch as required: OFF : Turns off the light.
AUTO : Automatically turns on the light when the
ON : Always keeps the light on as long as the
n The video light can only be used with the
n It is recommended to set the white balance
n When not using the video light, turn it off to save
camcorder senses insufficient lighting on the subject.
camcorder is turned on.
camcorder’s power on.
(Z pg. 32) to when you use the video light.
battery power.
NOTES:
Even if the battery indicator ( ) does not blink if the battery pack’s charge is low, the camcorder may turn off automatically when you turn on the video light, or when you start recording with the video light turned on.
When the LIGHT OFF/AUTO/ON Switch is set to “AUTO”:
Depending on the lighting conditions, the video light may keep turning on and off. In this case, manually switch the light on or off using the LIGHT OFF/AUTO/ON switch.
While the “Sports” or “High Speed Shutter” mode (Z pg. 23) is engaged, the light is likely to stay on.
While the “Twilight” mode (Z pg. 23) is engaged, the light will not activate.
RECORDING
20 EN
SNAPSHOT
SNAPSHOT Button
Power Switch
Display
RECORDING
Advanced Features
Snapshot (GR-FXM35 only)
Use your camcorder like a regular camera and take a snapshot, or several of them in succession.
SELECT OPERATION MODE
1
Set the Power Switch to “AUTO” or “PRO.”.
TAKE SNAPSHOT
2
Press SNAPSHOT.
If you press during Record-Standby . . .
.... a still image will be recorded for approx. 6 seconds,
then the camcorder re-enters the Record-Standby mode.
If you press during Recording . . .
.... a still image will be recorded for approx. 6 seconds,
then the normal recording resumes.
NOTE:
After SNAPSHOT is pressed, there is a momentary camera shutter-type blackout together with the sound effect of a shutter closing, which is recorded together with the image.
[Ex.: Fader]
Fade in
Display
EFFECT
MOSAIC
OFF (No indication)
EFFECT Button
After 2 sec.
EFFECT
MOSAIC
FADER
MOSAIC
SHUTTER
SLIDE
OFF
Power Switch
Recording Start/Stop Button
Fade out
EN21
Fade/Wipe
These effects let you make pro-style scene transitions. Fade- or wipe-in works at recording start, and fade- or wipe-out works at recording end or when you enter Record–Standby mode.
SELECT OPERATION MODE
1
Set the Power Switch to “PRO.”.
ENGAGE FADE- OR WIPE-STANDBY
2
MODE
Press EFFECT to cycle through the modes as shown at left. Once the desired mode appears, it is selected and reserved.
•The selected mode’s name and its indication are displayed for approx. 2 seconds. Then the name disappears, and only the indication remains.
START OR END RECORDING
3
Press the Recording Start/Stop Button to activate fade­in/out or wipe-in/out.
TO CANCEL FADE- OR WIPE-STANDBY
4
MODE
Press EFFECT repeatedly until “OFF” appears.
•“OFF” is displayed for approx. 2 seconds and the fade/wipe standby mode is canceled.
FADER
Fades in/out to a black screen.
MOSAIC (Fader)
Gradually turns/returns the picture into/from a mosaic pattern.
SHUTTER (Wipe)
A black screen moves in from the top and bottom, closing over the image like a shutter, or a new image pushes open the black screen vertically from the centre.
SLIDE (Wipe)
A black screen moves in from the left to gradually cover the image, or a new image moves in from right to left.
NOTES:
Pressing and holding the Recording Start/Stop Button allows you to vary the length for the image during fade in/out or wipe in/out.
The screen becomes slightly reddish when the Fade/ Wipe is used with Sepia (Z pg. 23).
With the Electronic fog filter mode (Z pg. 23) engaged, the image fades in/out to a white screen.
RECORDING
22 EN
:
SEPIA
Display
P.AE
After 2 sec.
RECORDING
Advanced Features (cont.)
Programme AE With Special Effects
All you have to do to access any of the variety of shooting effects is press P.AE.
SEPIA
SPORTS
:
ND EFFECT
ND
:
FOG
FG
TWILIGHT
S1/2000
NEGA/POSI
OFF
P.AE
:
SEPIA
ND
FG
OFF (No indication)
SELECT OPERATION MODE
1
Set the Power Switch to “PRO.”.
SELECT MODE
2
Press P.AE to cycle through the modes as shown on the left.
•The selected mode’s name and its indication are displayed for approx. 2 seconds. Then the name disappears, and only the indication remains. The mode is activated.
NOTES:
Only one mode can be engaged at a time.
The screen becomes slightly reddish when the Fade/ Wipe (Z pg. 21) is used in the Sepia mode.
The screen becomes slightly dark in the High Speed Shutter mode. Use in well-lit situations.
In the “High Speed Shutter” or “Sports” modes, picture colour may be adversely affected if the subject is lit by alternating discharge-type light sources such as flourescent or mercury-vapour lights.
P.AE Button
Power Switch
Display Mode
EN23
Display Mode
SEPIA
Sepia
The scene being shot is recorded in sepia-tinted (reddish-brown) monochrome, giving the effect of an older movie. Use together with Wide (Z pg. 27) for the authentic look of a classic Hollywood movie.
SPORTS
Sports
High shutter speed clearly captures fast-moving action.
ND:ND EFFECT
ND Effect
A black mist darkens the picture, as when an ND filter is used. Helps to counter the effects of glare on the subject.
FG:FOG
Electronic Fog Filter
Makes the picture look misty white, as when an external fog filter is attached to the lens. Softens the image and gives it a “fantasy” look.
Sepia
Sports
ND Effect
Electronic Fog Filter
S1/2000
High-Speed Shutter (1/2000s.)
Captures faster action than Sports mode.
NEGA POSI
Nega/Posi (Negative/Positive)
The colours of a picture are reversed.
1/2000 sec. High Speed Shutter
Nega/Posi
NEGA POSI mode
RECORDING
TWILIGHT
Twilight
Dusk, twilight scenery, fireworks, etc., look more natural and dramatic. The following happens when Twilight mode is selected:
•Auto gain control is turned off.
•White Balance is set to “ ” (FINE day mode), but can also be manually changed to another mode (Z pg. 32).
•Auto Focus becomes available only in the range of 10 m to infinity. To focus when the subject-to­camera distance is less than 10 m, use manual focusing (Z pg. 31).
Twilight
24 EN
Select Dial
FOCUS EXPOSURE WIDE S.LX TITLE
DATE TIME DISP.
4
RETURN
DATE TIME DISP.
AUTO DATE
DATE TIME DATE&TIME OFF
EXIT
FOCUS EXPOSURE WIDE S.LX TITLE DATE TIME DISP.
4
RETURN
Display
AUTO AUTO OFF OFF
AUTO AUTO OFF OFF
25. 12. 99
Power Switch
Menu Screen
DATE/TIME DISP. Menu
RECORDING
Advanced Features (cont.)
Date/Time Insert
The feature allows you to display the date and time on the LCD monitor, in the viewfinder, or on a connected colour monitor, as well as to record them manually or automati­cally.
SELECT OPERATION MODE
1
Set the Power Switch to “PRO.”.
ACCESS MENU SCREEN
2
Press the Select Dial to display the Menu Screen.
ACCESS “DATE/TIME DISP.” MENU
3
Move the highlight bar to “DATE/TIME DISP.” by rotating the Select Dial while in Record-Standby. Then press it to display the DATE/TIME DISP. Menu.
SELECT THE DESIRED MODE
4
Move the highlight bar to the desired mode by rotating the Select Dial, then press it. The desired mode is activated.
•You should have already performed the Date/Time Setting procedure (Z pg. 7). If you haven’t, do so first.
CLOSE MENU SCREEN
5
The Menu Screen reappears with the highlight bar on “RETURN”. Then press the Select Dial to close the Menu Screen.
NOTES:
DISPLAY
The selected display can be recorded.
If you do not want to record the display, select the OFF mode before shooting.
AUTO DATE
Your camcorder automatically records the date for about 5 seconds after recording is initiated in the following situations:
After changing the date.
After loading a cassette.
After Auto Date Record mode is selected by rotating the Select Dial.
In this mode, the date is replaced after 5 seconds with “AUTO DATE” but this is not recorded.
AUTO DATE
25 . 12 . 99
(DATE)
22 : 50 : 00
(TIME)
25 . 12 . 99
(DATE&TIME)
OFF (No indication)
22 : 50 : 00
Select Dial
Display
FOCUS EXPOSURE WIDE S.LX
TITLE
DATE TIME DISP.
4
RETURN
AUTO AUTO OFF OFF
Power Switch
Menu Screen
EN25
Instant Titles
The camcorder has eight preset titles in memory. You can superimpose one of them above a previously stored title as shown in the illustration on left.
SELECT OPERATION MODE
1
Set the Power Switch to “PRO.”.
ACCESS MENU SCREEN
2
Press the Select Dial to display the Menu Screen.
ACCESS “TITLE” MENU
3
Move the highlight bar to “TITLE” by rotating the Select Dial while in Record-Standby. Then press it to display the TITLE Menu.
SELECT THE DESIRED MODE
4
Move the highlight bar to the desired mode by rotating the Select Dial, then press it. The desired mode is activated.
•If you wish to make the title indication disappear, select “OFF”.
CLOSE MENU SCREEN
5
The Menu Screen reappears with the highlight bar on “RETURN”. Then press the Select Dial to close the Menu Screen.
RECORDING
TITLE
OFF
HAPPY BIRTHDAY HAPPY HOLIDAYS OUR FAMILY MOVIE STAR PARTY TIME MERRY CHRISTMAS WEDDING DAY CONGRATULATIONS EXIT
FOCUS EXPOSURE WIDE S.LX TITLE DATE TIME DISP.
4
RETURN
CONGRATULATIONS
AUTO AUTO OFF OFF
TITLE Menu
26 EN
Select Dial
MENU Button
Display (ex. Menu Screen available using the MENU Button)
4
NEXT
M . W . B . D . ZOOM TELE MACRO DATE TIME TAPE LENGTH
4
RETURN
4
BACK
REC. TIME
INT. TIME TALLY LAMP JLIP ID NO DEMO MODE
 4
RETURN
OFF 1/4S 1/2S
1 S
5 S
EXIT
4
BACK REC. TIME INT. TIME TALLY LAMP JLIP ID NO DEMO MODE
4
RETURN
AUTO ON OFF
T45
OFF
OFF ON 06 OFF
REC TIME
1S OFF ON 06 OFF
Normal Screen
NOTE:
No menu functions except “FOCUS” and “EXPOSURE” are available while in the Record mode.
Menu Screen 1
Menu Screen 2
Setting Menu (ex. REC TIME)
RECORDING
Advanced Features (cont.)
Using Menu For Detailed Adjustment
This camcorder is equipped with an easy-to-use, on-screen menu system that simplifies many of the more detailed camcorder settings.
SELECT OPERATION MODE
1
Turn the Power Switch to “PRO.”.
ACCESS MENU SCREEN
2
Menu access depends on the function you select.
If you select the functions from the “Menu Screen Available Using The Select Dial” described on pg. 27 . . .
.... press the Select Dial. The Menu Screen appears.
If you select the functions from the “Menu Screen Available Using The MENU Button” described on pg. 27 and 28 . . .
.... press MENU. The Menu Screen appears.
SELECT FUNCTION
3
Rotate the Select Dial to place the highlight bar on the desired function.
•To go from Menu Screen 1 to Menu Screen 2, rotate the Select Dial to “NEXT” and press it. To go back to Menu Screen 1 from Menu Screen 2, rotate the Select Dial to “BACK”, and press it.
•If the setting you want cannot be found in the Menu Screen, place the highlight bar on “RETURN”, then go to step 6.
MAKE SETTING
4
Press the Select Dial. The setting procedure depends on the function you select.
If you select “FOCUS”, “EXPOSURE”, “TITLE”, “DATE/TIME DISP.” or “DATE/ TIME” . . .
.... see respective pages (FOCUS: Z pg. 30, 31,
EXPOSURE: DATE/TIME DISP.:
If you select “WIDE”, “D.ZOOM”, “TELE MACRO” or “DEMO MODE” . . .
.... the selected function’s parameter starts blinking.
Rotate the Select Dial until the desired parameter appears. Go to step 5.
If you select “JLIP ID NO.” . . .
.... press the Select Dial so that the number blinks, then
rotate it until the desired number appears, and press it. Then rotate the Select Dial to move the highlight bar to “EXIT”.
If you select any other functions . . .
.... rotate the Select Dial to move the highlight bar to the
desired setting.
• If you decide you want to return to the previous setting, rotate the Select Dial to move the highlight bar to “EXIT”.
END SETTING
5
Press the Select Dial. The Menu Screen reappears with the highlight bar on “RETURN”.
CLOSE MENU SCREEN
6
Press the Select Dial. The normal screen reappears.
Z pg. 29, TITLE: Z pg. 25,
Z pg. 24, DATE/TIME: Z pg. 7).
MENU SCREEN EXPLANATIONS
Menu Screen Available Using The Select Dial
FOCUS
EXPOSURE
WIDE
S.LX
TITLE DA TE/TIME DISP.
AUTO MANU AUTO MANU OFF ON
MAX
NORMAL
OFF
Allows you to superimpose one of eight preset titles (Z pg. 25). Makes the date/time settings appear in the camcorder or on a connected monitor
(
Z pg. 24).
Adjusts focus automatically. Allows you to adjust focus manually (Z pg. 30, 31). Adjusts exposure automatically. Allows you to adjust exposure manually (Z pg. 29). Does not display black bars. Allows you to record black bars at the top and bottom of the screen
to produce a cinema-like “wide-screen” effect. If a snapshot (GR-FXM35 only, camcorder is in the WIDE mode, the snapshot image is recorded using NORMAL mode without the black bars at the top and bottom of the screen.
To record a subject in a darkly lit environment, it is more convenient to shoot the subject with a brighter image even if the picture becomes slightly coarse.
To record a subject in a dimly lit environment, when it is more convenient to shoot with a less coarse picture although the subject becomes slightly dark.
Allows you to shoot dark scenes with no picture brightness adjustment.
EN27
Z pg. 20) is taken while the
RECORDING
Menu Screen Available Using The MENU Button
This Menu Screen cannot be accessed while recording.
M.W.B.
D. ZOOM
TELE MACRO
: Factory-preset
AUTO
: FINE : CLOUD : HALOGEN
MWB
ON
OFF
OFF ON
This camcorder’s Automatic Colour Temperature system senses the colour temperature of the ambient lighting for automatic white balance adjustment. However, precise colour adjustment is not possible under the following conditions:
• When an object is in various shades of the same colour.
• When a predominantly red or brown object is being shot outdoors. In these cases, use the camcorder’s built-in preset filters for
white balance adjustment (Z pg. 32, 33). Allows you to use the Digital Zoom. By digitally processing and
magnifying images, zooming is possible from 16 times (the optical zoom limit), to a maximum of 320 times (GR-FXM35)/50 times (GR-FXM25) digital magnification.
Digital Zoom is not available. Only optical zoom (maximum 16x magnification) can function. When set to “OFF” during Digital Zoom, zoom magnification changes to 16x.
Usually the distance to a subject where the lens is in focus depends on the zoom magnification. Unless there is a distance of more than 1m to the subject, the lens is out of focus at the maximum telephoto setting. When set to “ON”, you can shoot a subject as large as possible at a distance of approx. 60 cm.
• Depending on the zoom position, the lens may go out of focus.
CONTINUED ON NEXT PAGE
28 EN
RECORDING
Menu Screen Available Using The MENU Button (cont.)
DATE/TIME TAPE LENGTH
REC TIME
INT. TIME
TALLY LAMP
JLIP ID NO.
DEMO MODE
Allows you to set the current date and time (Z pg. 7). Allows you to set the tape length depending on the tape used (Z pg. 8). This feature allows you to set the parameters for Animation and Time-Lapse
recording (Z pg. 35). This feature allows you to set the parameters for Self-Timer (Z pg. 34) and Time-
Lapse recording (Z pg. 34, 35).
OFF ON
This number is necessary when connecting the camcorder to a device such as a computer using the J terminal (JLIP). The numbers range from 01 to 99. Factory setting is 06.
OFF ON
The tally lamp remains off at all times. The tally lamp comes on to signal the start of recording.
Automatic demonstration will not take place. Demonstrates certain functions such as Fade/Wipe, etc. When
“DEMO MODE” is set to “ON” and the Menu Screen is closed, the demonstration starts.
NOTES:
When a tape whose Erase Protection tab is in the position that allows recording is loaded in the camcorder, demonstration is not available.
By turning off the camcorder or inserting a tape whose Erase Protection tab is in the position that allows recording into it, “DEMO MODE” is set to “OFF” automatically.
During the demonstration, all functions except zoom are disabled.
Advanced Features (cont.)
: Factory-preset
Select Dial Power Switch
Display
FOCUS
EXPOSURE
WIDE S.LX TITLE DATE TIME DISP.
4
RETURN
AUTO
MANU
EXIT
AUTO
AUTO
OFF OFF
EXPOSURE
00
Menu Screen
EXPOSURE Menu
Manual Exposure Screen
Exposure control level counter
EN29
Exposure Control
This feature automatically adjusts the iris for the best available picture quality, but you can override and make the adjustment manually.
SELECT OPERATION MODE
1
Set the Power Switch to “PRO.”.
ACCESS MENU SCREEN
2
Press the Select Dial to display the Menu Screen.
ACCESS “EXPOSURE” MENU
3
Rotate the Select Dial to move the highlight bar to “EXPOSURE” and press it.
ACCESS MANUAL EXPOSURE
4
Rotate the Select Dial to move the highlight bar to “MANU”, then press it. “00” (exposure control level counter) appears.
ADJUST EXPOSURE
5
To brighten the image . . .
.... rotate the Select Dial upward. The exposure
control level counter increases (maximum +06). Go to step 6.
To darken the image . . .
.... rotate the Select Dial downward. The exposure
control level counter decreases (maximum –06). Go to step 6.
END ADJUSTMENT OF EXPOSURE
6
Press the Select Dial. The Menu Screen reappears with the highlight bar on “RETURN”.
CLOSE MENU SCREEN
7
Press the Select Dial. The Menu Screen disappears and the exposure control level counter reappers to indicate the exposure is adjusted.
NOTES:
To return to the factory setting, select “AUTO” in step 4.
To re-adjust exposure, repeat the procedure from step 2.
RECORDING
To brighten the image
06 06
+
06
To darken the image
30 EN
Focus detection zone
RECORDING
Advanced Features (cont.)
Focusing
AUTO FOCUS
The camcorder’s Full Range AF system offers continuous shooting ability from close-up to infinity. However, correct focus may not be obtainable in the situations listed below (in these cases use manual focusing):
•When two subjects overlap in the same scene.
•When illumination is low.*
•When the subject has no contrast (difference in bright­ness and darkness), such as a flat, one-colour wall, or a clear, blue sky.*
•When a dark object is barely visible in the viewfinder.*
•When the scene contains minute patterns or identical patterns that are regularly repeated.
•When the scene is affected by sunbeams or light reflecting off the surface of a body of water.
•When shooting a scene with a high-contrast background.
* The low-contrast warning “ ” appears.
NOTES:
If the lens is smeared or blurred, accurate focusing is not possible. Keep the lens clean, wiping with a piece of soft cloth if it gets dirty. When condensation occurs, wipe with a soft cloth or wait for it to dry naturally.
When shooting a subject close to the lens, zoom out first (Z pg. 16). If zoomed in in the auto focus mode, the camcorder could automatically zoom out depending on the distance between the camcorder and the subject. When Tele Macro (Z pg. 27) is activated, the camcorder will not zoom out automatically.
Select Dial Power Switch
EN31
MANUAL FOCUS
NOTE:
You should already have made the necessary viewfinder adjustments (Z pg. 10). If you haven’t, do so before continuing.
SELECT OPERATION MODE
1
Set the Power Switch to “PRO.”.
ACCESS MENU SCREEN
2
Press the Select Dial to display the Menu Screen.
ACCESS “FOCUS” MENU
3
Move the highlight bar to “FOCUS” by rotating the Select Dial, then press it.
ACCESS MANUAL FOCUS
4
Rotate the Select Dial to move the highlight bar to “MANU”, then press it. “ ” and “ ” appear. The focus is locked at this point.
Display
FOCUS
EXPOSURE WIDE S.LX TITLE DATE TIME DISP.
4
RETURN
FOCUS
AUTO
MANU
EXIT
AUTO
AUTO OFF OFF
Menu Screen
FOCUS Menu
Manual Focus Screen
ADJUST FOCUS
5
To farther subject . . .
.... rotate the Select Dial upward. “ ” appears and
blinks. Go to step 6.
To nearer subject . . .
.... rotate the Select Dial downward. “ ” appears
and blinks. Go to step 6.
END ADJUSTMENT OF FOCUS
6
Press the Select Dial. The Menu Screen reappears with the highlight bar on “RETURN”.
CLOSE MENU SCREEN
7
Press the Select Dial. The Menu Screen disppears and “ ” reappears to indicate the focus is locked.
NOTES:
To return to Auto Focus, select “AUTO” in step 4.
To re-adjust Manual Focus, repeat the procedure from step 2.
Be sure to focus the lens in the maximum telephoto position when you use the Manual Focus mode. If you focus in on a certain subject in the wide-angle position, sharply focused images cannot be obtained when zoomed in because the depth-of-field is reduced at longer focal lengths.
When the focus level cannot be adjusted any farther or closer, “ ” or “ ” will blink.
RECORDING
32 EN
4
NEXT
M . W . B .
D . ZOOM TELE MACRO DATE TIME TAPE LENGTH
4
RETURN
AUTO
:
FINE
:
CLOUD
:
HALOGEN
MWB
EXIT
MENU Button
Display
AUTO
ON OFF
T45
M.W.B.
Power SwitchSelect Dial
Menu Screen
M.W.B. Menu
RECORDING
Advanced Features (cont.)
White Balance Adjustment
A term that refers to the correctness of colour reproduction under various lighting. If the white balance is correct, all other colours will be accurately reproduced. The white balance is usually adjusted automatically. However, the more advanced camcorder operator would prefer to control this function manually and achieve a more professional colour/tint reproduction.
SELECT OPERATION MODE
1
Set the Power Switch to “PRO.”.
ACCESS MENU SCREEN
2
Press MENU. The Menu Screen appears.
ACCESS WHITE BALANCE
3
ADJUSTMENT
Move the highlight bar to “M.W.B.” by rotating the Select Dial, then press it. The Menu Screen disap­pears and the “M.W.B.” Menu appears.
SET FUNCTION PARAMETERS
4
Move the highlight bar to the required white balance by rotating the Select Dial.
AUTO” The white balance is adjusted automatically. This is the factory preset position.
: FINE” When shooting outdoors on a sunny day.
: CLOUD” When shooting outdoors on a cloudy day.
: HALOGEN”
When using a video light or other similar type of lighting.
MWB” When shooting with the white balance already having been set on the subject (Z pg. 33).
CLOSE MENU SCREEN
5
Press the Select Dial. The Menu Screen reappears with the highlight bar on “RETURN”. Press the Select Dial again to close the Menu Screen.
To Return To Automatic White Balance . . .
.... select “AUTO” in step 4. Or set the Power Switch to
“AUTO”.
NOTE:
White balance cannot be used when Sepia (Z pg. 23) is activated.
White paper
EN33
Manual White Balance Operation
If the camera is operating in PRO. mode, perform a Manual White Balance when shooting under various types of lighting.
SELECT OPERATION MODE
1
Follow steps 1 through 4 of the white balance adjustment (Z pg. 32), and select “MWB”.
SET MANUAL WHITE BALANCE
2
Hold a sheet of plain white paper in front of the subject. Adjust zoom or position yourself so that the white paper fills the screen.
ENTER SETTING
3
Press the Select Dial until “MWB” begins blinking.
•When the setting is completed, “MWB” stops blinking, and the Menu Screen reappears with the highlight bar on “RETURN”.
CLOSE MENU SCREEN
4
Power SwitchSelect Dial
Press the Select Dial again to close the Menu Screen.
RECORDING
Display
4
NEXT
M . W . B .
D . ZOOM TELE MACRO DATE TIME TAPE LENGTH
4
RETURN
M.W.B.
AUTO
:
FINE
:
CLOUD
:
HALOGEN
MWB
EXIT
AUTO
ON OFF
T45
Menu Screen
M.W.B. Menu
To Change The Tint For Recording . . .
.... in step 2, substitute coloured paper for white. The
white balance is adjusted based on the colour, changing the tint. Red paper — deeper green; blue paper — orange; yellow paper — deeper purple.
NOTES:
In step 2, it may be difficult to focus on the white paper in some circumstances. In such a case, adjust focus manually (Z pg. 31).
A subject can be shot under various types of lighting conditions indoors (natural, flourescent, candlelight, etc.). Because the colour temperature is different depending on the light source, the tint of the subject will differ depending on the white balance settings. Use this function for a more natural result.
Once you adjust white balance during Manual White Balance operation, the setting is retained even if the power is turned off or the battery removed.
34 EN
4
NEXT
M . W . B . D . ZOOM TELE MACRO DATE TIME TAPE LENGTH
4
RETURN
4
BACK
REC. TIME
INT. TIME TALLY LAMP JLIP ID NO DEMO MODE
MENU Button
Select Dial
Display
AUTO ON OFF
T45
OFF
OFF ON 06 OFF
Recording Start/Stop Button
Menu Screen 1
Menu Screen 2
RECORDING
Advanced Features (cont.)
Self-Timer
You can set the delay between pressing the Recording Start/Stop button and the actual start of recording. If you secure the camcorder, you (or whoever is operating the camcorder) can enter the scene before recording starts.
NOTE:
Make sure the Power Switch is set to “PRO.” and the camcorder is in the Record-Standby mode before performing the following steps.
ACCESS MENU SCREEN
1
Press MENU.
ACCESS “INT. TIME” MENU
2
Rotate the Select Dial to move the highlight bar to “NEXT” in Menu Screen 1 and press it to display Menu Screen 2. Then, move the highlight bar to “INT. TIME” and press it.
SET INTERVAL TIME
3
Rotate the Select Dial to move the highlight bar to the desired time, then press it. The Menu Screen reappears with the highlight bar on “RETURN”.
CLOSE MENU SCREEN
4
Press the Select Dial.
START DELAYED RECORDING
5
Press the Recording Start/Stop Button. When the selected time has elapsed, recording begins auto­matically.
To Cancel Self-Timer . . .
.... Before the recording begins, press the Recording Start/
Stop Button to display “ ”, then set “INT. TIME” in the Menu Screen to “OFF”.
4
RETURN
INT. TIME
OFF
15S
30S
1 MIN
5 MIN
EXIT
INT. TIME Menu
15S 1S
INT. TIME and REC TIME indications on the normal screen
REC TIME
OFF 1 4S 1 2S
1 S
5 S
EXIT
REC TIME Menu
INT. TIME indicator
REC TIME indicator
Animation
You can give stationary scenes or objects an illusion of movement. This function allows you to shoot a series of pictures, each slightly different, of the same object for a brief period of time.
NOTE:
Before performing the following steps, make sure that:
The Power Switch is set to “PRO.”.
The camcorder is in the Record-Standby mode.
The recording mode is set to “SP”.
ACCESS MENU SCREEN
1
Press MENU.
SET RECORDING TIME
2
Rotate the Select Dial to move the highlight bar to “NEXT” in Menu Screen 1 and press it to display Menu Screen 2. Then, move the highlight bar to “REC TIME” and press it. The REC TIME Menu appears. Rotate the Select Dial to move the highlight bar to the desired time, then press it. The Menu Screen reappears with the highlight bar on “RETURN”. Press the Select Dial again to close the Menu Screen.
START RECORDING
3
Press the Recording Start/Stop Button after focusing on the subject. The recording stops automatically after the selected period of time.
ASSEMBLE SERIES OF PICTURES
4
Repeat step 3 for the desired number of pictures.
RELEASE ANIMATION MODE
5
Set “REC TIME” in the Menu screen to “OFF”.
EN35
Time-Lapse
You can record sequentially at preset time spans. Leaving the camcorder aimed at a specific subject, you can record subtle changes over an extended period of time.
NOTE:
Before performing the following steps, make sure that:
The Power Switch is set to “PRO.”.
The camcorder is in the Record-Standby mode.
The recording mode is set to “SP”.
ACCESS MENU SCREEN
1
Press MENU.
SET INTERVAL BETWEEN
2
RECORDINGS
Rotate the Select Dial to move the highlight bar to “NEXT” in Menu Screen 1 and press it to display Menu Screen 2. Then, move the highlight bar to “INT. TIME” and press it. The INT. TIME Menu appears. Rotate the Select Dial to move the highlight bar to the desired time, then press it. The Menu Screen reappears.
SET RECORDING TIME
3
Rotate the Select Dial to move the highlight bar to “REC TIME”, then press it. The REC TIME Menu appears. Rotate the Select Dial to move the highlight bar to the desired time, then press it. The Menu Screen reappears with the highlight bar on “RETURN”. Press the Select Dial again to close the Menu Screen.
START TIME-LAPSE RECORDING
4
Press the Recording Start/Stop Button. Recording and intervals alternate automatically.
RECORDING
NOTES:
For best results, make sure the camcorder is secured when shooting in Animation or Time­Lapse mode.
Fade- or wipe-in/out cannot be performed during Animation or Time-Lapse shooting.
Before performing other operations following Animation or Time-Lapse recording, make sure the Animation or Time-Lapse mode is deactivated.
Self-Timer, Animation and Time-Lapse are canceled when the power is shut off or when the cassette is ejected.
RELEASE TIME-LAPSE MODE
5
To release when “ ” is displayed, set “REC TIME” and “INT. TIME” in the Menu Screen to “OFF”. To release when “ ” and “ ” are not displayed, press the Recording Start/Stop Button to display “ ”, then set “REC TIME” and “INT. TIME” in the Menu Screen to “OFF”.
36 EN
EJECT Switch
LCD Monitor in Retracted Position
Power lamp
Power Switch
REW (2) Button
3
) Button
FF (
PLAY/PAUSE (4/6) Button
STOP (5) Button
PLAYBACK
Basic Playback
LOAD A CASSETTE
1
First open the LCD monitor to an angle of over 60 degrees. Slide EJECT to open the cassette holder, then insert the cassette with the label facing out. Press PUSH to ensure the holder is closed and locked.
SELECT MODE
2
Make sure the LCD monitor is fully open, then set the Power Switch to “PLAY”. The power lamp lights.
PLAY BACK
3
Press PLAY/PAUSE (4/6). The playback picture appears.
STOP PLAYBACK
4
Press STOP (5).
Rewind or Fast-Forward the tape
Press REW (2) to rewind, or FF (3) to fast-forward the tape during Stop mode.
NOTES:
The camcorder shuts off automatically after about 5 minutes in Stop mode. To turn on again, set the Power Switch to “POWER OFF”, then to “PLAY”.
When the Power Switch is set to “PLAY” and the LCD monitor is opened at an angle of 60 degrees or more, the LCD monitor switches on and the viewfinder switches off automatically to save power.
The playback picture can also be viewed in the viewfinder (with the LCD monitor shut) or on a connected TV (Z pg. 40, 41). Camcorder operation is the same as described in this section.
You can also view the playback picture on the LCD monitor with it flipped over and retracted.
If a blank portion on the tape is played back, the screen may become black. This is not a malfunction.
Battery pack remaining power indicator
Tape counter
Recording mode indicator
S ET
SP
M 1 : 23 : 45
TAPE END
VOLUNE
LCD monitor/viewfinder indications
Tape running indicator
AT
4 3
2
6 : Still Playback
: Playback : Fast-Forward/
Forward Search
: Rewind/Reverse
Search
PLAYBACK
BRIGHT Dial
BRIGHT
BRIGHT
VOLUME
Features
Power Zoom Lever
Speaker
P.AE Button EFFECT Button
Display
EN37
Adjust the brightness of the LCD monitor
To brighten the image, turn the BRIGHT Dial towards “+”. To darken the image, turn the Dial towards “–”.
Speaker Volume Control
You can adjust the speaker volume by pushing the Power Zoom Lever.
ADJUST VOLUME
1
If you want to turn up the volume . . .
.... push the Power Zoom Lever towards “T”.
If you want to turn down the volume . . .
.... push the Power Zoom Lever towards “W”.
Tracking
This function can be used to eliminate noise bars that appear on-screen during playback. Initial setting is Auto Tracking. Manual Tracking is also available.
ACTIVATE MANUAL TRACKING
1
Press P.AE and EFFECT simultaneously. Then, press P.AE or EFFECT as many times as necessary until the
noise bars disappear.
•To return to Auto Tracking, press P.AE and EFFECT
simultaneously. “AT” blinks. When Auto Tracking finishes, the indication disappears.
NOTES:
When noise bars appear during playback, the camcorder enters the Auto Tracking mode and “AT” is displayed.
Manual Tracking may not work with tapes recorded on other VCRs or camcorders.
PLAYBACK
38 EN
Power Switch
FEATURE:
PLAYBACK
Still Playback
Features (cont.)
PURPOSE:
To pause during playback.
OPERATION:
1) Press PLAY/PAUSE (4/6) during playback.
2) To resume normal playback, press PLAY/PAUSE
(4/6) again.
NOTE:
Noise bars appear and pictures may become monochrome during Still Playback. This is normal.
REW (
2
) Button
FF (
3
PLAY/PAUSE ( Button
STOP (5) Button
COUNTER R/M Button
) Button
4
/6)
FEATURE:
Shuttle Search
PURPOSE:
To allow high-speed search in either direction.
OPERATION:
1) Press FF (3) to search forward or press REW (2)
to reverse during playback.
2) To resume normal playback, press PLAY/PAUSE
(
4
/6).
NOTES:
During playback, press and hold REW (2) or FF (3). The search continues as long as you hold
the button. Once you release it, normal playback resumes.
Noise bars appear and pictures may become monochrome or darken during Shuttle Search. This is normal.
FEATURE:
Counter Memory Function
PURPOSE:
To make it easier to locate a specific tape segment.
OPERATION:
1) Press COUNTER R/M and hold for more than 1
second. The counter resets to “0:00:00”.
2) Press COUNTER R/M for less than 1 second. “M”
appears.
3) After recording or playback, press STOP (5), then REW (
2
to 0:00:00.
4) Press PLAY/PAUSE (4/6) to start playback.
). The tape automatically stops at or close
NOTES:
The counter memory functions in the Fast-Forward and Rewind modes.
To disable the Counter Memory Function, press COUNTER R/M for less than 1 second so that “M” disappears.
PLAYBACK
Compact video cassette
Using The Cassette Adapter
Cassette Adapter
Use this to play back a VHS-C video cassette recorded with this camcorder on a VHS VCR. It is fully compatible with any VHS video cassette recorder. The C-P7U adapter is battery powered and automatically performs tape loading and unloading.
1
VCR
2
Compartment door
3 4
Sliding latch
Reels
NOTES:
During tape loading and unloading, do not touch the reels for safety and tape protection.
During special-effect playback (slow motion, still frame, etc.), the picture may vibrate or noise bars may appear on the screen.
To record on a VCR using a compact cassette and the adapter, cover the adapter’s recording safety hole with adhesive tape.
EN39
INSERT BATTERY
Slide the battery cover up to remove it, and install one “R6(AA)” size battery as shown in the illustration on left, then reattach the cover.
INSERT CASSETTE IN ADAPTER
Slide the latch to open the adapter compartment door, then insert the cassette and close the compartment door.
PLAY BACK ON CONNECTED VCR
Load the cassette adapter into the VCR and play the tape back as you would any other.
REMOVE CASSETTE FROM ADAPTER
Slide the latch and the compartment door opens automatically. This may take around 10 seconds. Do not attempt to force the adapter open. Then, insert your finger in the hole on the underside of the adapter as shown in the illustration at left, and push up and remove the cassette.
PLAYBACK
Recording safety hole
40 EN
These are some basic types of connections. When making connections, refer also to your VCR and TV instruction manuals.
A. Connection to a TV or VCR equipped with an S-VIDEO
Basic Connections
Use the provided Video and Audio cables.
PLAYBACK
Basic Connections And Tape Dubbing
To Video Output
To Audio Output
Connector cover*
A. Connection to a TV or VCR equipped with an S-VIDEO
Connection For Tape Dubbing
Use the provided Video and Audio cables.
Video cable (provided)
To AUDIO and VIDEO IN connectors
Audio cable (provided)
Power Switch
PLAY/PAUSE (
4
/6) Button
To TV or VCR
TV
VCR
TV
To Video Output
Connector cover*
* When connecting the cables, open this cover.
To Audio Output
Video cable (provided)
To AUDIO and VIDEO IN connectors
Audio cable (provided)
VCR (Recording deck)
Basic Connections
EN41
Tape Dubbing
CONFIRM POWER-OFF STATUS
1
Make sure the camcorder’s power is off.
CONNECT CAMCORDER TO TV OR
2
VCR
Pull out the connector cover and open it. Connect as shown in the illustration (Z pg. 40).
If using a VCR . . . go to step 3. If not . . . go to step 4.
CONNECT VCR OUTPUT TO TV
3
INPUT
Refer to your VCR’s instruction manual.
SUPPLY POWER
4
Turn on the camcorder, the VCR and the TV.
SELECT MODE
5
Set the VCR to its AUX input mode, and set the TV to its VIDEO mode.
NOTES:
It is recommended to use the AC Power Adapter/ Charger as the power supply instead of the battery pack (Z pg. 5).
To monitor the picture and sound from the camcorder without inserting a tape, set the camcorder’s Power Switch to “CAMERA” (“AUTO” or “PRO.”), then set your TV to the appropriate input mode.
Make sure you adjust the TV sound volume to its minimum level to avoid a sudden burst of sound when the camcorder is turned on.
If you have a TV or speakers that are not specially shielded, do not place the speakers adjacent to the TV as interference will occur in the camcorder playback picture.
CONNECT EQUIPMENT
1
Following the illustration on pg. 40, connect the camcorder and the VCR.
PREPARE FOR DUBBING
2
Set the camcorder’s Power Switch to “PLAY”, turn on the VCR’s power, and insert the appropriate cassettes in the camcorder and the VCR.
SELECT VCR MODE
3
Engage the VCR’s AUX and Record-Pause modes.
FIND EDIT-IN POINT
4
Engage the camcorder’s Play mode to find a spot just before the edit-in point. Once it is reached, press PLAY/PAUSE (4/6) on the camcorder.
START EDITING
5
Press PLAY/PAUSE (4/6) on the camcorder and engage the VCR’s Record mode.
STOP EDITING TEMPORARILY
6
Engage the VCR’s Record-Pause mode and press PLAY/PAUSE (4/6) on the camcorder.
EDIT MORE SEGMENTS
7
Repeat steps 4 through 6 for additional editing, then stop the VCR and camcorder when finished.
PLAYBACK
42 EN
The Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic operations (Playback, Stop, Pause, Fast-Forward and Rewind) of your VCR. The RM-V700U remote control unit makes additional recording functions possible.
USING THE REMOTE CONTROL UNIT
A
2
1
3
B
2
1
Lock hole
1
3
4
5
6
7
8
9
RM-V700U (provided with GR-FXM35, optional for GR-FXM25)
Buttons
1 PAUSE IN Connector 2 Infrared beam
transmitting window
3 MBR SET Button 4 INT. TIME Button 5 REC TIME Button 6 FF Button
7 REW Button
8 PAUSE Button 9 PLAY Button 0 START/STOP Button ! VISS Button @ ZOOM (T/W) Buttons # VCR CTL Button $ A.DUB Button % STOP Button ^ INSERT Button & R.A.EDIT Buttons
1
With the camcorder’s Power Switch set to “CAMERA”, “AUTO” or “PRO.”.
Transmits the beam signal.
Self-Timer/Time-Lapse (Z pg. 43) Animation/Time-Lapse (Z pg. 43) Retake (forward) (Z pg. 17)
Retake (rewind)/Quick Review (Z pg. 17)
Functions same as the Recording Start/Stop button on the camcorder. Ineffective Zoom in/out (Z pg. 16)
3
1
Release tab
2
0
!
@
#
$
%
^
&
Installing The Battery
The remote control uses one lithium battery (CR2025).
PULL OUT BATTERY HOLDER
1
: Pull out the battery holder while sliding
the lock hole.
: Pinch the release tab and pull out the
battery holder.
INSERT BATTERY IN HOLDER
2
Insert the battery in the holder, and be sure to have the “+” mark visible.
RE-INSERT HOLDER
3
Slide the holder back in until you hear a click.
•Read the caution concerning lithium batteries (Z pg. 2).
Functions
With the camcorder’s Power Switch set to “PLAY”.
— —
— — — — —
Z pg. 45
Z pg. 44
— —
Fast-Forward, Forward Shuttle Search
Z pg. 36, 38)
( Rewind, Reverse Shuttle Search
Z pg. 36, 38)
( Pause (Z pg. 38) Playback start (Z pg. 36)
Z pg. 44
Audio dubbing (Z pg. 49) Stop (Z pg. 36) Insert Editing (Z pg. 48)
Z pg. 46
EN43
Transmitted beam effective area
Remote sensor
When using the remote control, be sure to point it at the remote sensor. The illustration shows the approximate transmitted beam effective area for indoor use. The transmitted beam may not be effective or may cause incorrect operation outdoors or when the remote sensor is directly exposed to sunlight or powerful lighting.
Interval timer indicator
1 2S
Rec time indicator
START/STOP
INDEX1MIN
Remote sensor
FEATURE:
Self-Timer, Animation and Time-Lapse
PURPOSE:
The remote control lets you set/release Interval Timer and Rec Time functions without using the Menu Screen.
OPERATION:
Self-Timer
1) Set
Instead of performing steps 1 through 4 on pg. 34 (“Self-Timer”), press INT. TIME on the remote control. Each time INT. TIME is pressed, the Interval Timer indicator appears, changing in the following order: 15S, 30S, 1MIN, 5MIN and No indication (off).
2) Release
Instead of setting “INT. TIME” to “OFF” in the Menu, press INT. TIME on the remote control until the Interval Timer indicator disappears.
Animation
1) Set
Instead of performing steps 1 and 2 on pg. 35 (“Animation”), press REC TIME on the remote control. Each time REC TIME is pressed, the Rec Time indicator appears, changing in the following order: 1/4S, 1/2S, 1S, 5S and No indication (off).
2) Release Instead of using the Menu in step 5 on pg. 35, press REC TIME on the remote control until the Rec Time
indicator disappears.
Time-Lapse
1) Set
Instead of performing steps 1 through 3 on pg. 35 (“Time-Lapse”), press INT. TIME and REC TIME on the remote control. Each time INT. TIME is pressed, the Interval Timer indicator appears, changing in the following order: 15S, 30S, 1MIN, 5MIN and No indication (off). Each time REC TIME is pressed, the Rec Time indicator appears, changing in the following order: 1/4S, 1/2S, 1S, 5S and No indication (off).
2) Release Instead of using the Menu in step 5 on pg. 35, press INT. TIME and REC TIME on the remote control until
the indicators disappear.
NOTE:
Also refer to pgs. 34 and 35.
INT. TIME
REC TIME
RM-V700U (provided with GR-FXM35, optional for GR-FXM25)
44 EN
USING THE REMOTE CONTROL UNIT
VCR (Recording deck)
(cont.)
Random Assemble Editing [R.A.Edit]
Create edited videos easily using your camcorder as the source player. You can select up to 8 “cuts” for automatic editing, in any order you like. R.A.Edit is more easily performed when the RM-V700U MBR (Multi-Brand Remote, Z pg. 42) is set to operate with your brand of VCR (see VCR CODE LIST), but can also be performed by operating the VCR manually. Before operation, make sure the lithium battery is installed in the remote control RM-V700U (Z pg. 42).
SET REMOTE/VCR CODE
RM-V700U (provided with GR-FXM35, optional for GR-FXM25)
VCR CODE LIST
VCR BRAND NAME
AKAI
BLAUPUNKT FERGUSON
GRUNDIG 1 4
HITACHI 6 6
JVC 9 1
A B C
MITSUBISHI 6 7
NEC 3 7
PANASONIC 1 3
BUTTONS
(A) (B)
6 2 6 4 7 7
1 3
9 7 9 8 3 2
3 4
6 3
9 6 9 3
6 8
3 8
1 7 1 1 9 4 1 8
2 3
1
4
5 6
8
0
9
7
VCR BRAND NAME
PHILIPS
SANYO 3 6
SELECO, REX
SHARP 1 5
SONY
THOMSON, TELEFUNKEN, SABA, NORDMENDE
TOSHIBA 6 9
MBR SET
VCR CTL
BUTTONS
(A) (B)
1 9 9 5 1 1 9 4 9 1 9 6 1 2 3 3 7 2
3 5 9 1
9 6
1 ` 6 5
6 ` 3 9 3 1
9 1 9 6 9 7 3 2
6 1
SET REMOTE TO OPERATE VCR
1
Turn off the power to the VCR and point the remote towards the VCR’s infrared sensor. Then, referring to the VCR CODE LIST on the left, press and hold MBR SET, and press button (A) and then (B).
•The code is automatically set once you release
MBR SET, and the VCR’s power comes on.
OPERATE VCR
2
Make sure the VCR’s power is on. Then, while holding VCR CTL, press the button on the remote for the desired function. The functions the remote can control are PLAY, STOP, PAUSE, FF, REW and VCR REC STBY (you do not need to press VCR CTL for this one).
You are now ready to try Random Assemble Editing.
IMPORTANT
Although the MBR is compatible with JVC VCRs and those of many other makers, it may not work with
 
yours or may offer limited functions.
NOTES:
If the VCR’s power does not come on in step 1, try another code from the VCR CODE LIST.
Some brands of VCR do not come on automatically. In this case, turn the power on manually and try step 2.
If the remote control is not able to control the VCR, use the controls on the VCR.
When the remote control’s battery runs out, the VCR brand you have set will be erased. In that case, replace the old battery with a new one and reset the VCR brand.
Open the cover.
To J terminal (JLIP)
Editing cable* (ø3.5 mini-plug cable)
To Audio Output
Audio cable (provided)
Open the cover.
To Video Output
Video cable (provided)
To AUDIO and VIDEO IN connectors
MAKE CONNECTIONS
CONNECT TO . . .
1
JVC VCR EQUIPPED WITH REMOTE PAUSE TERMINAL
Connect the editing cable to the Remote PAUSE terminal.
JVC VCR NOT EQUIPPED WITH REMOTE PAUSE TERMINAL BUT EQUIPPED WITH R.A. EDIT CONNECTOR
Connect the editing cable to the R.A.EDIT connector.
VCR OTHER THAN TYPE OR
Connect the editing cable to the RM-V700U’s PAUSE-IN connector.
PREPARE CAMCORDER
2
Insert a recorded tape, and set the Power Switch to “PLAY”.
PREPARE VCR
3
Turn the power on, insert a recordable tape and engage the AUX mode (refer to the VCR’s instructions).
EN45
To Remote PAUSE
To PAUSE-IN
RM-V700U*
*Provided with GR-FXM35, optional for GR-FXM25.
VCR
TV
CONTINUED ON NEXT PAGE
46 EN
Power Switch
USING THE REMOTE CONTROL UNIT
Remote sensor
REW
PLAY
IN/OUT
RM-V700U (provided with GR-FXM35,
optional for GR-FXM25)
IN
1
0:00:25 2 3 4 5 6 7 8 COUNTER TOTAL
IN 1
0:00:25 2
0:03:18 3
0:02:33 4
0:04:11 5 6 7 8 COUNTER TOTAL
OUT
--:--:--
0:00:25 0:00:00
OUT 0:01:05 0:03:31 0:02:53
--:--:--
0:04:11 0:01:13
FF PAUSE
CANCEL ON/OFF
(cont.)
SELECT SCENES
START SOURCE PLAYBACK
4
Press PLAY, then press ON/OFF on the remote control. Make sure to point the remote control at the camcorder’s remote sensor.
•The R.A. Edit counter display appears.
REGISTER BEGINNING OF SCENE
5
Press REW or FF to locate the beginning of the scene you want, then press IN/OUT to register that point.
•The data appears under “IN” on the display.
REGISTER END OF SCENE
6
Press REW or FF to locate the end of the scene and press IN/OUT to register it.
•The data appears under “OUT” on the display.
•The total time of the registered scene(s) is displayed at the bottom of the screen.
REGISTER ADDITIONAL SCENES
7
Repeat steps 5 and 6 for each additional scene (as many as 8).
MAKE CORRECTIONS (IF NECESSARY)
8
Press CANCEL during steps 5 and 6 to erase the most recently registered point.
NOTES:
There must be at least one second between an in-point and its corresponding out-point.
To ensure correct operation, there should be at least 15 seconds between an out-point and the next in-point.
Blank portions of a tape cannot be registered as in-points or out-points.
If it takes more than 5 minutes to search for an in-point, the VCR’s Record-Pause mode is cancelled and editing does not take place.
Pressing ON/OFF clears all in- and out-points from memory.
Leave a small margin for error around each in-point to ensure the scene is recorded in its entirety.
Turning off the camcorder’s power erases all registered in- and out-points.
Original tape (camcorder)
1 3 2
IN OUT IN OUT IN OUT
Edited tape (VCR)
STOP (5) Button
REW (
2
) Button
PAUSE (6) Button
Remote Sensor
MENU/DISPLAY Button
Power Switch
RM-V700U
Recording Start/Stop Button
(provided with GR-FXM35, optional for GR-FXM25)
ON/OFF
VCR REC STBY
EN47
AUTOMATIC EDITING TO VCR
PREPARE SOURCE TAPE
9
Rewind the tape in the camcorder to the beginning of the scene you want to edit and press PAUSE.
ENGAGE VCR’S RECORD-PAUSE MODE
10
Point the remote control towards the VCR’s infrared sensor and press VCR REC STBY, or manually engage the VCR’s Record-Pause mode.
BEGIN AUTOMATIC EDITING
11
Press MENU/DISPLAY on the camcorder, and the previously selected scenes are copied to the VCR in the specified order. While editing, the R.A. Edit counter of the scene which is being copied is shown with a blinking highlight.
•Pressing START/STOP on the remote control does not start editing.
END AUTOMATIC EDITING
12
When all selected scenes have been copied, the camcorder and VCR enter the Still or Pause mode. Press STOP on both units. To make the R.A. Edit counter display disappear, press ON/OFF.
•When finished editing, be sure to disconnect the editing cable and the audio/video cable.
NOTES:
If you performed step 1 on page 45 (“MAKE CON­NECTIONS”), keep the remote control pointed at the VCR during editing.
The on-screen display only appears while the camcorder searches for each scene.
There may be noise at in- or out-points on the edited tape with certain VCRs.
SUPPLEMENTAL INFORMATION ON THE REMOTE CONTROL
Player (JVC VCR)
To R.A. EDIT Editing cable*
To PAUSE IN
RM-V700U*
* Provided with
GR-FXM35, optional for GR-FXM25.
AV OUT
AV I N
Recording deck
Using the RM-V700U, it is also possible to perform deck-to-deck Random Assemble Editing. The playback deck must be an R.A. Edit­capable JVC VCR. The recording deck can be...
n a VCR other than JVC, or n a JVC VCR which has neither a Remote PAUSE nor an R.A. EDIT
connector
How to use:
— Connect the playback deck and RM-V700U as shown on the left. — Set the RM-700U to correspond to the brand of the recording
deck. (
— For Random Assemble Editing procedure, please refer to the
Z pg. 44)
instruction manual of the JVC VCR you are using as the playback deck.
Notes:
n RM-V700U cannot be used to control the playback deck. n RM-V700U is capable of controlling basic operations of the
recording deck. While pressing VCR CTL, press PLAY, STOP, PAUSE, FF or REW for these functions. (Not possible with some brands and models). Other buttons cannot be used.
n To put the recording deck in the Record-Pause mode, use the
controls on the recording deck itself.
48 EN
w
M 0 : 12 : 34
Display
USING THE REMOTE CONTROL UNIT
Power Switch
REW (
2
FF (
3
) Button
PLAY/PAUSE (
STOP (5) Button
COUNTER R/M Button
) Button
4
/6) Button
Insert editing indicator
Tape Counter
(cont.)
Insert Editing
You can record a new scene onto a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in- and out-points. The original audio remains unchanged.
NOTE:
Use the RM-V700U remote control unit to perform this procedure.
SELECT OPERATION MODE
1
Set the Power Switch to “PLAY”.
FIND EDIT-OUT POINT
2
Play back the tape, locate the point and press PAUSE on the camcorder or the remote control.
RESET COUNTER
3
Press and hold COUNTER R/M for more than 1 second to reset the tape counter, then press again for less than 1 second so that “M” appears.
FIND EDIT-IN POINT
4
Press REW to go a little beyond the beginning of the scene you want to replace, press PLAY to view the recorded tape, and press PAUSE exactly at the point where the new scene should start.
ENGAGE INSERT EDITING MODE
5
Press and hold INSERT, and without releasing INSERT, press and release PAUSE. The Insert Editing
mode is engaged. When the scene the camcorder is aimed at appears on the screen, go to the next step.
START/STOP
REW
PLAY
Remote sensor
RM-V700U (provided with
GR-FXM35, optional for
GR-FXM25)
PAUSE
STOP
INSERT
BEGIN INSERT EDITING
6
Press START/STOP. When the counter reaches “0:00:00”, editing stops automatically and the camcorder enters the Insert-Pause mode.
END INSERT EDITING
7
Press STOP.
NOTES:
During Insert Editing, the original audio will be heard from the speaker.
After step 5, Retake (Z pg. 17) can be performed.
The tape may stop slightly before or after the designated end point, and noise bars may appear. Neither indicates a defect in the unit.
Only the video signal is recorded in the Insert Editing mode.
Display
e
4
M 0 : 05 : 20
Remote sensor
REW PLAY
RM-V700U (provided with
GR-FXM35, optional for
GR-FXM25)
Audio dubbing indicator
Microphone
A. DUB STOP
PAUSE
EN49
Audio Dubbing
You can record a new soundtrack on a prerecorded tape (normal audio only).
Perform steps 1, 2 and 3 of the Insert Editing procedure (Z pg. 48) before continuing.
•The sound comes from the built-in microphone.
FIND EDIT-IN POINT
1
Press REW to go a little beyond the beginning of the scene onto which you want to dub the new audio, press PLAY to view the recorded tape, then press PAUSE at exactly the point where dubbing should start.
ENGAGE AUDIO DUB-STANDBY MODE
2
Press and hold A. DUB, and without releasing A. DUB, press and release PAUSE.
BEGIN AUDIO DUBBING
3
Press PLAY. When the counter reaches “0:00:00”, Audio Dubbing stops automatically and the camcorder enters the Audio Dub-Standby mode.
END AUDIO DUBBING
4
Press STOP.
NOTES:
Do not press FF or REW during Audio Dub-Standby, or the edit points will not be accurate.
If the microphone is too close to the TV, or if the TV’s volume is too high, whistling or howling may occur.
NOTES (for Insert Editing and Audio Dubbing):
Insert Editing and Audio Dubbing may not work correctly if the tape contains blank segments, or if the recording speed was changed during the original recording.
To edit/dub onto a tape, make sure the Erase Protection tab is in the position that allows recording. If not, slide the tab. Some cassettes have removable tabs. If the tab has been removed, cover the hole with adhesive tape.
Do not press STOP during Insert Editing or Audio Dubbing, or the edit points will not be accurate.
During Insert Editing and Audio Dubbing, when Insert­Pause or Audio Dub-Standby is engaged, the counter may go slightly past “0:00:00”. Recording, however, stops at exactly 0:00:00.
50 EN
If, after following the steps in the chart below, the problem still exists, please consult your JVC dealer.
The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Power Adapter/Battery Charger, etc.) and clock battery; and then re-connect it and proceed as usual from the beginning.
TROUBLESHOOTING
SYMPTOM POSSIBLE CAUSE(S)
POWER
No power is supplied.
The battery pack has not been attached correctly (Z pg. 4).
The battery pack is not charged (Z pg. 4).
The power supply has not been correctly connected
(Z pg. 5).
The power suddenly goes off and does not come back on by itself.
RECORDING
Recording cannot be performed.
Recording does not start.
Animation or Time-Lapse is not available.
PLAYBACK
The tape is running, but there is no playback picture.
Playback picture is blurred or interrupted.
The counter indication is blurred during Still playback.
The battery pack has completely discharged.
Remove the cassette and disconnect the power source, then
after a few minutes, try turning the power back on. If it still does not come on, consult your nearest JVC dealer.
Make sure the Erase Protection tab is in the position that allows recording. If not, slide the tab. Some cassettes have removable tabs. If the tab has been removed, cover the hole with adhesive tape.
The camcorder Power Switch has not been set to “CAMERA” (“AUTO” or “PRO.”) (Z pg. 12).
Before recording in the Animation mode at the very beginning of a tape, set the camcorder to the Recording mode for about 5 seconds, so that the tape runs smoothly. Using the Fade-in function at this point is a good way to begin an animated program (Z pg. 35, 43).
The TV has not been set to its VIDEO mode or channel.
If A/V connection is used, the TV’s VIDEO/TV Switch has
not been set to VIDEO.
The video heads are dirty or worn out. Consult your nearest JVC dealer for head cleaning or replacement.
This is normal.
TAPE TRANSPORT
The tape stops during fast-forward or rewind.
Rewinding or fast-forwarding cannot be performed.
The Counter Memory Function has been activated
Z pg. 38).
(
The tape is already fully wound on one reel or the other.
SYMPTOM POSSIBLE CAUSE(S)
OTHER
During recording, the indications do not appear.
The tape will not eject.
Some functions are not available.
Vertical white lines appear when shooting a very bright object.
Bright, crystal-shaped spots appear in the LCD monitor and the viewfinder.
The rear of the LCD monitor is hot.
Coloured bright spots appear all over the LCD monitor or the viewfinder.
The indicators and the picture colour on the LCD monitor are not clear.
The LCD monitor, the viewfinder and the lens have become dirty (ex. fingerprints).
An error number (i.e. E03) appears.
The image is out of focus.
The picture is blurred in the Quick Review or Retake mode.
The date and time displays disappear.
The wrong date and time are displayed/recorded.
Even though the lens cover is open, the Lens Cover Warning indicator blinks.
EN51
Press DISPLAY for longer than 1 second to make the indications appear (Z pg. 13).
The battery pack is running low.
If the LCD monitor is not open over 60 degrees, the EJECT
Switch does not function.
The Power Switch is set to “AUTO”.
Certain combinations of modes or effects are not possible
to use.
This sometimes occurs when the contrast between the background and the object is great. It is not a defect of the camcorder.
Sunlight is directly entering the lens. This is not a defect of the camcorder.
The light used to illuminate the LCD monitor causes it to be hot. Close the LCD monitor to turn it off or set the Power Switch to “OFF”, and let the unit cool down.
The LCD monitor and the viewfinder are made with high­precision technology. However, black spots or bright spots of light (red, green or blue) may appear constantly on the LCD monitor or in the viewfinder. These spots are not recorded on the tape. This is not due to any defect of the unit. (Effective dots: more than 99.99 %.)
This may occur when the surface or the edge of the LCD monitor is pressed.
Wipe them gently with a soft cloth. Gently wipe in a semicircular motion, as wiping strongly spreads the stain and it won’t come out easily.
Turn the camcorder’s power off, then disconnect the power source. After a few minutes, try turning the power on again. If the error number still appears, consult your nearest JVC dealer.
The dioptre needs to be adjusted (Z pg. 10).
The scene being shot is adversely affecting the operation of
Auto Focus (Z pg. 30).
This is normal while recording in the LP mode. Some noise may be present while recording in the SP mode (Z pg. 8).
If you remove the power source from the camcorder while the power is on, all settings and selections are erased. Make sure to turn the camcorder’s power off before disconnecting the power source.
If you have not performed Date/Time Setting (Z pg. 7), the date and time are not displayed/recorded correctly. Be sure that Date/Time setting is carried out.
The Lens Cover Warning indicator may blink when the camcorder is used in dark areas, regardless of the position of the lens cover.
52 EN
INDEX
Controls, Connectors And Indicators
T
1
i
q
o
)
u
tew2
p
Q W
7 8
9 !
#
^
0 @
$ %
E
R
Y
3 4 5 6
r
& (*
y
U I
Controls
1 Dioptre Adjustment Control ................. Z pg. 10
2 Lens Cover Open/Close Ring
[LENS COVER] .................................... Z pg. 12
3 Video Light Switch [LIGHT OFF/AUTO/ON]
(GR-FXM35 only)................................. Z pg. 19
4 •Snapshot Button [SNAPSHOT]
(GR-FXM35 only) .............................. Z pg. 20
•5-Second Recording Button [5 SEC REC]
(GR-FXM25 only) .............................. Z pg. 18
5 •Power Zoom Lever [T/W] .................. Z pg. 16
•Speaker Volume Control [VOL.] ........ Z pg. 37
6 Picture Stabilizer Button
[P.STABILIZER] ..................................... Z pg. 18
7 Program AE Button [P.AE] ..................... Z pg. 22
8 Fade/Wipe Button [EFFECT] ................. Z pg. 21
9 •Rewind Button [
•Retake Rewind Button [RETAKE R]..... Z pg. 17
•Quick Review Button [ R] ............. Z pg. 17
0 •Fast-Forward Button [
•Retake Forward Button [RETAKE F] .... Z pg. 17
! Stop Button [5, STOP] ......................... Z pg. 36
@ Play/Pause Button
[4/6, PLAY/PAUSE] ............................. Z pg. 36
# •Select Dial [+, –, PUSH]................ Z pg. 7, 26
•Bright Dial [BRIGHT] ........................ Z pg. 15
$ MENU/DISPLAY Button ................. Z pg. 13, 26
% •Counter Reset/Memory Button
[COUNTER R/M] .............................. Z pg. 38
•Recording Mode Button [SP/LP]........... Z pg. 8
^ EJECT Switch ......................................... Z pg. 9
& Recording Start/Stop Button.................. Z pg. 12
* Power Switch ................................ Z pg. 12, 36
( Battery Release Switch
[BATTERY RELEASE] .............................. Z pg. 4
) PUSH Button ......................................... Z pg. 9
2
, REW] ................ Z pg. 36
3
, FF] ............ Z pg. 36
EN53
Connectors
q DC IN Jack ............................................ Z pg. 5
The connectors w to r are located beneath the cover.
w Video Output Connector ...................... Z pg. 40
e Audio Output Connector ..................... Z pg. 40
r J Terminal [JLIP (Joint Level Interface Protocol)
Connector]
• Connect the editing cable when performing Random Assemble Editing (
• It is used to connect the camcorder to a device such as a personal computer. For further details consult your nearest JVC dealer.
• JLIP-controlled editing from camcorder to VCR is not possible if the VCR is not equipped with a J terminal.
Z pg. 44 - 47).
Indicators
t Tally Lamp ........................................... Z pg. 12
y Power Lamp ........................................ Z pg. 12
Other Parts
u Battery Pack Mount ............................... Z pg. 4
i Viewfinder ........................................... Z pg. 10
o Grip Strap ............................................ Z pg. 10
p • Camera sensor
Be careful not to cover this area; a sensor necessary for shooting is built-in here.
•Remote Sensor .................................. Z pg. 43
Q Video Light (GR-FXM35 only) .............. Z pg. 19
W Microphone ......................................... Z pg. 49
E Eyepiece
R Speaker ............................................... Z pg. 37
T LCD Monitor ....................................... Z pg. 14
Y Shoulder Strap Eyelets .......................... Z pg. 11
U Clock Battery Slot .................................. Z pg. 6
I Tripod Mounting Socket ....................... Z pg. 11
54 EN
INDEX
Indications
2
30MIN T45
6
REC SP
FINE 10
F ADER
7
8
9
0
! @ #
1 Cassette Warning/
Tape Remaining Time ..........................
When no cassette is inserted: the cassette ( warning blinks. When the Erase Protection tab is not in the position that allows recording: the cassette ( lights. Otherwise, the tape remaining time is displayed and the tape remaining time warning blinks when the tape is about to reach its end. When the Power Switch is set to “PLAY” and a tape is loaded: the cassette ( displayed regardless of the Erase Protection tab’s position.
2 Recording Mode (SP/LP) Indicator .......... Z pg. 8
3, 7 Programme AE Indicator ................. Z pg. 22
Displayed at Programme AE with special effects is switched from one mode to another by pressing P.AE., then only the indicator remains at
3, 8 Fade/Wipe-Standby Indicator .......... Z pg. 21
Displayed at Fade/Wipe is switched from one effect to another by pressing EFFECT, then only the indicator remains at
4 Tape Length Indicator ............................ Z pg. 8
5 Zoom Indicator Bar ............................. Z pg. 16
6 Recording Indicator ............................. Z pg. 12
9 Picture Stabilizer Indicator ................... Z pg. 18
0 •Interval Timer/Recording Time
Indicator .....................................
•5 Sec. Rec Mode Indicator
(GR-FXM25 only) ..............................
! Instant Title Display ............................. Z pg. 25
@ Date/Time Display............................... Z pg. 24
# •Bright Level Indicator ........................ Z pg. 37
•Speaker Volume Indicator .................
8.
Zoom Level Indicator Approximate Zoom Ratio
2
LENS COVER
PAUSE 15S 5S
T APE END
MERRY CHRISTMAS
25. 12. 99 BRIGHT
) mark is
3 for approx. 2 seconds when
7.
3 for approx. 2 seconds when the
NORM
Z pg. 13
)
) warning
Z pg. 34, 43
Z pg. 18
Z pg. 37
431
5
$
%
01
^
&
20X
INDEX
*
1X
(
)
22 : 50 : 00
$ Battery Pack Remaining Power Indicator
Changes as follows according to the battery pack’s remaining power level: “ almost gone, the indicator “ power warning), then the unit shuts off. Replace the battery pack with a fully charged one.
Note: The symbol containing 3 darkened squares —
— does not necessarily mean that the battery
pack is fully charged.
% Focus Indicator.................................... Z pg. 31
^ Exposure Control Level Counter ........... Z pg. 29
& White Balance Mode Indicator ............ Z pg. 32
* •Record–Standby Mode Indicator ....... Z pg. 12
•Lens Cover Warning:
LENS COVER....................................
( Clock Battery Warning
Blinks for approx. 10 seconds when the power is turned on. This display also blinks when the clock (lithium) battery is either not installed or has discharged. Install or replace the old battery with a new one (
) •Tape End Display: TAPE END ............ Z pg. 13
Appears when the end of the tape is reached during playback, recording or fast-forward.
• Condensation Warning: When this indication appears, all functions except tape eject and power on/off are disabled. Turn the unit off (without removing the power source) for a few hours, and when you turn it on again the indication should disappear.
• Head Clog Warning: Appears if dirty heads are detected during recording. In such a case, use the optional Cleaning Cassette. If, after using it, the problems still exist, consult your nearest JVC dealer.
Z pg. 6).
”. When the power is
b
” blinks (battery
a
Z pg. 13
CAUTIONS
DANGER:
Video Light
• The video light becomes extremely hot. Do not touch it either while in operation or soon after turning it off, otherwise serious injury may result.
• Do not place the camcorder into the carrying case immediately after using the video light, since it remains extremely hot for some time.
• When operating, keep a distance of about 30 cm between the video light and people or object.
• Do not use near flammable or explosive materials.
• It is recommended that you consult your nearest JVC dealer for replacing the video light.
General Battery Precautions
•When the C-P6U or C-P7U (cassette adapter) is not functioning even when correctly operated, the battery is exhausted. Replace it with a fresh one.
•Use only the following battery:
C-P6U or C-P7U..................... R6 (AA) size
Please make note of the following rules for battery use. When misused, battery can leak or explode.
1. Refer to the C-P6U/C-P7U instructions when
replacing the battery.
2. Do not expose the battery to excessive heat as it
can leak or explode.
3. Do not dispose of battery in a fire.
4. Remove battery from the unit if it is to be stored
for an extended period to avoid battery leakage which can cause malfunctions.
Battery Packs
The battery packs are nickel-cadmium or nickel metal-hydride batteries. Before using the supplied battery pack or an optional battery pack, be sure to read the following cautions:
1. To avoid hazard . . .
... do not burn. ... do not short-circuit the terminals. ... do not modify or disassemble. ... use only specified chargers.
2. To prevent damage and prolong service life . . .
... do not subject to unnecessary shock. ... avoid repeated charging without fully
discharging.
... charge in an environment where temperatures
are within the tolerances shown in the chart below. This is a chemical reaction type battery—cooler temperatures impede chemical reaction, while warmer temperatures can prevent complete charging.
Terminals
EN55
... store in a cool, dry place. Extended exposure to
high temperatures will increase natural
discharge and shorten service life. ... avoid prolonged uncharged storage. ... remove from charger or powered unit when not
in use, as some machines use current even
when switched off.
NOTES:
It is normal for the battery pack to be warm after charging, or after use. Temperature Range Specifications
Charging .............. 10°C to 35°C
Operation ............ 0°C to 40°C
Storage ................ –10°C to 30°C
Recharging time is based on room temperature of 20°C.
The lower the temperature, the longer recharging takes.
Cassettes
To properly use and store your cassettes, be sure to read the following cautions:
1. During use . . .
... make sure the cassette bears the VHS-C mark. ... be aware that recording onto prerecorded tapes
automatically erases the previously recorded
video and audio signals. ... make sure the cassette is positioned properly
when inserting. ... do not load and unload the cassette repeatedly
without allowing the tape to run at all. This
slackens the tape and can result in damage. ... do not open the front tape cover. This exposes
the tape to fingerprints and dust.
2. Store cassettes . . .
... away from heaters or other heat sources. ... out of direct sunlight. ... where they won’t be subject to unnecessary
shock or vibration. ... where they won’t be exposed to strong
magnetic fields (such as those generated by
motors, transformers or magnets). ... vertically, in their original cases.
Main Unit
1. For safety, DO NOT . . .
... open the camcorder’s chassis. ... disassemble or modify the unit. ... short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not in
use. ... allow inflammables, water or metallic objects
to enter the unit. ... remove the battery pack or disconnect the
power supply while the power is on. ... leave the battery pack attached when the
camcorder is not in use.
56 EN
2. Avoid using the unit . . .
... in places subject to excessive humidity or dust. ... in places subject to soot or steam such as near a
cooking stove.
...
in places subject to excessive shock or vibration. ... near a television set. ... near appliances generating strong magnetic or
electric fields (speakers, broadcasting antennas,
etc.). ... in places subject to extremely high (over 40°C)
or extremely low (under 0°C) temperatures.
3. DO NOT leave the unit . . .
... in places of over 50°C. ... in places where humidity is extremely low
(below 35%) or extremely high (above 80%). ... in direct sunlight. ... in a closed car in summer. ... near a heater.
4. To protect the unit, DO NOT . . .
... allow it to become wet. ... drop the unit or strike it against hard objects. ... subject it to shock or excessive vibration during
transportation. ... keep the lens directed at extremely bright
objects for long periods. ... direct the eyepiece of the viewfinder at the sun. ... carry it by holding the viewfinder or the LCD
monitor. Be sure to hold the main unit with
both hands or use the grip. ... swing it excessively when using the shoulder
strap.
LCD Monitor
1. To prevent damage to the LCD monitor, DO NOT . . .
... push it strongly or apply any shocks. ... place the camcorder with the LCD monitor on
the bottom.
2. To prolong service life . . .
... avoid rubbing it with coarse cloth.
3. Be aware of the following phenomena for LCD monitor use. These are not malfunctions . . .
• While using the camcorder, the surface around the
LCD monitor and/or the back of the LCD monitor may heat up.
• If you leave power on for a long time, the surface
around the LCD monitor becomes hot.
CAUTIONS
(cont.)
Serious malfunctioning
If malfunctioning occurs, stop using the unit immedi­ately and consult your local JVC dealer.
For Your Maintenance
1. After Use
1 Set the Power Switch to “POWER OFF” to turn off
the camcorder.
2 Open the LCD monitor to an angle of over 60
degrees. Slide EJECT to open the cassette holder, then remove the cassette.
3 Close and lock the cassette holder by pressing
PUSH.
4 Close and lock the LCD monitor. 5 Slide BATTERY RELEASE to remove the battery
pack.
6 Turn the LENS COVER Open/Close Ring to close
the lens cover.
2. Cleaning The Camcorder
1 CLEAN EXTERIOR
Wipe gently with a soft cloth. Put cloth in diluted mild soap and wring it well to wipe off heavy dirt, then wipe again with a dry cloth.
2 CLEAN LCD MONITOR
Open the LCD monitor and wipe it gently with a soft cloth. Be careful not to damage the monitor. Close the LCD monitor.
3 CLEAN LENS
Blow it with a blower brush, then wipe it gently with lens cleaning paper.
4 REMOVE EYEPIECE
Turn the eyepiece counterclockwise and pull it out.
5 CLEAN VIEWFINDER
Remove dust using a blower brush.
6 RE-ATTACH EYEPIECE
Re-attach the eyepiece and turn it clockwise.
NOTES:
Avoid using strong cleaning agents such as benzine or alcohol.
Cleaning should be done only after the battery pack has been removed or other power units have been disconnected.
Mould may form if the lens is left dirty.
When using a cleaner or chemically treated cloth, refer to the cautions that came with it.
When removing the eyepiece, be sure to hold the viewfinder securely.
About moisture condensation . . .
You may have observed that pouring a cold liquid into a glass will cause drops of water to form on the glass’ outer surface. This same phenomenon occurs on the head drum of a camcorder when it is moved from a cool place to a warm place, after heating a cold room, under extremely humid conditions or in a place directly subjected to the cool air from an air conditioner.
Moisture on the head drum can cause severe damage to the video tape, and can lead to internal damage to the camcorder itself.
SPECIFICATIONS
General
Format : VHS PAL standard Power source : DC 6.0 V Power consumption
LCD monitor off, viewfinder on : 5.7 W
LCD monitor on, viewfinder off : 6.2 W LCD monitor on,
viewfinder on : 6.8 W Video light (GR-FXM35 only) : 2.9 W Signal system : PAL-type Video recording system
Luminance : FM recording
Colour : Converted sub-carrier
Cassette : Tape speed
SP : 23.39 mm/sec. LP : 11.70 mm/sec.
Recording time (max.)
SP : 60 minutes LP : 120 minutes
Connectors
JLIP : ø3.5 mm, 4-pole, mini-head
Video : 1 Vp-p, 75 unbalanced,
direct recording Conforms to VHS standard
cassette
(with EC-60 cassette)
jack (compatible with RC-5325 plug)
analogue output (via Video output connector)
Camcorder
Operating temperature Operating humidity : 35% to 80% Storage temperature : –20°C to 50°C Weight : Approx. 880g Dimensions : 99 (W) x 119 (H) x 198 (D) mm
Pickup : 1/4” format CCD Lens : F1.6, f = 3.9 to 62.4 mm, 16:1
Viewfinder : Electronic viewfinder with
White balance
adjustment : Auto/Manual adjustment
LCD monitor : 2.5” diagonally measured, LCD
Speaker : Monaural
Audio : –8 dBs, 1 k analogue output
: 0°C to 40°C
(with the LCD monitor closed and with the viewfinder fully tilted downward)
power zoom lens with auto iris and macro control, filter diameter 40.5 mm
0.5” black/white CRT
panel/TFT active matrix
(via Audio output connector)
EN57
AC Power Adapter/Charger AA-V15EG
Power requirement : AC 110 V to 240 V`,
Power consumption : 23 W Output
Charge : DC 8.5 V
VTR : DC 6.3 V , 1.8 A Charging system : Constant current, peak
Dimensions : 140 (W) x 42 (H) x 68 (D) mm Weight : Approx. 300 g
50/60 Hz
, 1.3 A
detection, timer controlled
Cassette Adapter C-P7U
Dimensions : 188 (W) x 25 (H) x 104 (D) mm Weight : Approx. 240 g Accessory : “R6 (AA)”-size battery x 1
Provided Accessories ..................Z pg. 3
Optional Accessories
•Battery Packs BN-V12U, BN-V20U, BN-V856U
•Car Battery Charger BH-V3E
•Compact VHS (
•Active Carrying Bag CB-V7U
•Remote Control Unit RM-V700U
Some accessories are not available in some areas. Please consult your nearest JVC dealer for details on accessories and their availability.
E & O.E. Design and specifications subject to change without notice.
) Cassettes EC-60/45/30
MEMO
MEMO
GR-FXM35
GR-FXM25
ED
Printed in Japan 0299FOV*UN*SN
EN
VICTOR COMPANY OF JAPAN, LIMITED
®Registered Trademark owned by VICTOR COMPANY OF JAPAN, LTD. COPYRIGHT© 1999 VICTOR COMPANY OF JAPAN, LTD.
Loading...