JVC DR-DX5SU User Manual

Download

Mini DV & HDD & DVD VIDEO RECORDER

DR-DX5SU

CABLE/DBS

DVD

STANDBY/ON

TV/

DVD

TV/CBL/DBS

VIDEO

DV HDD DVD

TVVOL

AUX

CANCEL

MEMO/MARK

PROG

EDITDUBBING

LIVE

TVMUTING

NAVIGATIONTOPMENU

ENTER

RETURN

NEXTPREVIOUS

SLOWSLOW PLAY/SELECT

CLEAR

PAUSEREC

STOP/

JUMP

RECMODE

DISPLAY

ONSCREEN

SETUP

REMAIN

VPS/PDC

AUDIO

SUBTITLE

ANGLE

LIVECHECK

PROGRESSIVE

STANDBY/ON

SAT

S-VIDEO VIDEO

(MONO)

SCAN

L–AUDIO–R

F–1

DV– HDD– DVD–

RAM/RW

DV/HDD/DVD

SELECT

DISPLAY

VHS RECMODE

DVIN/OUT

DV/HDD

NTSC

INSTRUCTIONS

For Customer Use:

Enter below the Model No. and Serial No. which are located on the rear of cabinet. Retain this information for future reference.

Model No.

Serial No.

LPT1099-001A

2 EN

SAFETY FIRST

Dear Customer,

Thank you for purchasing the JVC Mini DV & HDD & DVD video recorder. Before use, please read the safety information and precautions to ensure safe use of your new unit.

Cautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CABLE COMPATIBLE TELEVISION APPARATUS

- TELEVISION CABLOCOMPATIBLE , CANADA

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION:

A UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CLASS 1 LASER PRODUCT REPRODUCTION OF LABELS

WARNING LABEL INSIDE OF THE UNIT

RISQUE DE CHOC ELECTRIQUE

AVIS

- NE PAS OUVRIR.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION:

This unit should be used with AC 120VH, 60Hz only. To prevent electric shocks and fire hazards, DO NOT use any other power source.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

CAUTION:

Changes or modifications not approved by JVC could void user’s authority to operate the equipment.

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.

ATTENTION:

Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this booklet for future reference.

INSTALLATION

1. Grounding or Polarization

(A)Your product may be equipped with a polarized alternating-

current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

(B)Your product may be equipped with a 3-wire grounding-type

plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

2. Power Sources

Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.

3. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

4. Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

5. Ventilation

Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.

● Do not block the openings by placing the product on a bed, sofa,

rug or other similar surface.

● Do not place the product in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

6. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

SAFETY FIRST

ANTENNA INSTALLATION INSTRUCTIONS

1. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

2. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

3. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

EN 3

4 EN

SAFETY FIRST

USE

1. Accessories

To avoid personal injury:

● Do not place this product on an unstable cart, stand, tripod,

bracket, or table. It may fall, causing serious injury to a child or adult, and serious damage to the product.

● Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer or sold with the product.

● Use a mounting accessory recommended by the manufacturer

and follow the manufacturer’s instructions for any mounting of the product.

● Do not try to roll a cart with small casters across thresholds or

deep-pile carpets.

2. Product and Cart Combination

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

3. Water and Moisture

Do not use this product near water—for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like.

4. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

5. Attachments

Do not use attachments not recommended by the manufacturer of this product as they may cause hazards.

6. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

7. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

SERVICING

1. Servicing

If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

2. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to

qualified service personnel under the following conditions: a. When the power supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and will often

require extensive work by a qualified technician to restore the

product to its normal operation. e. If the product has been dropped or damaged in any way. f. When the product exhibits a distinct change in performance—

this indicates a need for service.

3. Replacement Parts

When replacement parts are required, be sure the service

technician has used replacement parts specified by the

manufacturer or which have the same characteristics as the

original part. Unauthorized substitutions may result in fire,

electric shock or other hazards.

4. Safety Check

Upon completion of any service or repairs to this product, ask

the service technician to perform safety checks to determine

that the product is in safe operating condition.

HOW TO USE THIS INSTRUCTION MANUAL

● All major sections and subsections are listed in the Table Of

Contents on page 6. Use this when searching for information on a specific procedure or feature.

● The Index on pages 12 - 15 illustrates the controls and

connections on the front and rear panel, the front display panel and the remote control.

● The list of terms on page 85 lists frequently-used terms, and the

number of the page on which they are used or explained in the manual.

● The A mark signals a reference to another page for instructions

or related information.

● Operation buttons necessary for the various procedures are

clearly indicated through the use of illustrations at the beginning of each major section.

BEFORE YOU INSTALL YOUR NEW UNIT . . .

. . . please read the sections/literature listed below.

● ACautionsB on page 2

● AIMPORTANT PRODUCT SAFETY INSTRUCTIONSB on pages 3

- 5

Declaration of Conformity

Model Number: DR-DX5SU Trade Name: JVC Responsible Party: JVC Americas Corp. Address: 1700 Valley Road Wayne, N.J. 07470 Telephone Number: 973-317-5000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

NTSC

● Manufactured under license from Dolby Laboratories. ADolbyB

and the double-D symbol are trademarks of Dolby Laboratories.

● ADTSB and ADTS DIGITAL OUTB are trademarks of Digital

Theater Systems, Inc.

● This unit can play back and record only NTSC signals. PAL

signals can also be played back on the DVD deck.

● VCR Plus+ and PlusCode are registered trademarks of Gemstar

Development Corporation. The VCR Plus+ system is manufactured under license from Gemstar Development Corporation.

● DSS

is an official trademark of DIRECTV, Inc., a unit of GM

Hughes Electronics. DISH Network

is a trademark of Echostar

Communications Corporation.

● This product incorporates copyright protection technology that is

protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

SAFETY FIRST

EN 5

When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear).

When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly.

Failure to heed the following precautions may result in damage to the unit, remote control or disc/cassette.

1. DO NOT

place the unit ^

^ in an environment prone to extreme temperatures or

humidity.

^ in direct sunlight.

^ in a dusty environment.

^ in an environment where strong magnetic fields are

generated.

^ on a surface that is unstable or subject to vibration.

2. DO NOT

block the unit’s ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper

or cloth, etc., the heat may not be able to get out.)

3. DO NOT

4. DO NOT

place heavy objects on the unit or remote control. place anything which might spill on top of the unit

or remote control.

(If water or liquid is allowed to enter this equipment, fire or

electric shock may be caused.)

5. DO NOT

6. DO NOT

expose the apparatus to dripping or splashing. use this equipment in a bathroom or places with

water. Also DO NOT place any containers filled with water or

liquids (such as cosmetics or medicines, flower vases, potted

plants, cups, etc.) on top of this unit.

7. DO NOT

place any naked flame sources, such as lighted

candles, on the apparatus.

8. AVOID

violent shocks to the unit during transport.

MOISTURE CONDENSATION

Moisture in the air will condense on the unit when you move it from a cold place to a warm place, or under extremely humid conditions^just as water droplets form on the surface of a glass filled with cold liquid. In conditions where condensation may occur, disconnect the unit’s power plug from the wall and keep it disconnected for a few hours to let the moisture dry, then turn on the unit.

DISCLAIMER OF LIABILITY

JVC shall not be liable for any loss relating to the unit’s failure to properly record, store or playback any content (video, audio or otherwise) for any reason whatsoever. Any applicable warranties shall only cover replacement or repair of the effected unit, and shall not apply to recovery or replacement of lost content.

ATTENTION:

8 Using a mobile phone in the vicinity of the unit may cause

picture vibration on the TV screen or change the screen to a blue back display.

8 Some TVs or other appliances generate strong magnetic

fields. Do not place such appliances on top of the unit as it may cause picture disturbance.

8 When moving the product, press A to turn off the power,

and wait at least 30 seconds before unplugging the power cord. Then, wait at least 2 minutes before moving the product.

8 If there is a power outage when using the unit, the recorded

data may be erased.

8 It is recommended to back up discs which contain important

recordings periodically (every few years). As digital signals do not deteriorate, failure to play back or record might arise due to the effects of the disc aging through the years depending on the storage environment.

8 Recorded programs and data cannot be restored once the

disc or tape is damaged.

6 EN

SAFETY FIRST 2

DISC INFORMATION 7

About Discs....................................................................................7

INDEX 12

INSTALLING YOUR NEW UNIT 18

Basic Connections .......................................................................18

INITIAL SETTINGS 19

Plug & Play Set ............................................................................19

Language .....................................................................................20

Clock Set......................................................................................21

Tuner Set .....................................................................................22

Monitor Set...................................................................................23

BASIC OPERATIONS ON DVD DECK 24

Basic Playback.............................................................................24

Playback Features .......................................................................25

Using The On-screen Bar ............................................................29

Parental Lock ...............................................................................33

Basic Recording...........................................................................34

Recording Features......................................................................35

BASIC OPERATIONS ON HDD DECK 37

Basic Recording...........................................................................37

Recording Features......................................................................38

Basic Playback.............................................................................39

Playback Features .......................................................................39

BASIC OPERATIONS ON DV DECK 41

Basic Playback.............................................................................41

Playback Features .......................................................................42

LIVE MEMORY PLAYBACK ON HDD/DVD DECK 43

Live Memory Playback.................................................................43

TIMER RECORDING ON HDD/DVD DECK 46

VCR Plus+ Timer Programming...................................................46

Manual Timer Programming.........................................................48

NAVIGATION ON HDD/DVD DECK 50

Library Database Navigation .......................................................50

Edit Original Information .............................................................. 51

Edit Play List Information............................................................. 53

Navigate Library Information ....................................................... 55

Playback With MP3/WMA/JPEG Navigation ...............................56

EDITING 57

Dubbing .......................................................................................57

DV Dubbing (HDD & DVD Deck Only) ........................................ 60

Edit From A Camcorder............................................................... 62

Edit To Or From Another Recorder ............................................. 63

Digital Audio Dubbing .................................................................. 64

Audio Dubbing (DV Deck Only) ................................................... 65

Insert Editing (DV Deck Only)...................................................... 66

REMOTE CONTROL 67

Remote Control Functions........................................................... 67

SYSTEM CONNECTIONS 69

Connecting To A Dolby Digital Decoder Or An Amplifier

With Built-in DTS....................................................................... 69

SUBSIDIARY SETTINGS 70

Mode Set .....................................................................................70

Changing VCR Plus+ Setting ...................................................... 73

Format A Disc (DVD Deck Only) .................................................74

Finalize A Disc (DVD Deck Only) ................................................75

Scan Mode Set (HDD & DVD Deck Only) ...................................76

Tray Lock (DVD Deck Only) ........................................................ 76

Child Lock.................................................................................... 76

TROUBLESHOOTING 77

APPENDIX 81

SPECIFICATIONS 84

LIST OF TERMS 85

WARRANTY (Only in U.S.A.) 86

FOR SERVICING (Only in U.S.A.) 88

About Discs

Recordable/Playable Discs

You can use discs with the following logos for recording and playback.

DVD-RAM

12 cm: 4.7 GB/9.4 GB 8 cm: 1.4 GB/2.8 GB Ver. 2.0/2x speed Ver. 2.1/1x – 3x speed Ver. 2.2/5x speed

DVD-R

12 cm: 4.7 GB 8 cm: 1.4 GB Ver. 2.0/1x – 4x/8x speed (Video mode)

● The above table is based on the information as of September

2005.

● Recording and playback may not be performed depending on the

characteristics and condition of the disc used, leading to unsatisfactory results. Using discs manufactured by JVC is recommended since they have been tested to be compatible with this unit.

DVD-RAM Discs

It is only possible to use discs which conform with DVD-RAM standard Version 2.0 or 2.1.

● It is impossible to record on DVD-RAM discs which do not

conform to this standard. If you use a disc formatted under a different standard version, format it on this unit before use.

● It may not be possible to record, play back, edit or dub a

DVD-RAM disc even if it conforms to the standard if it was recorded or edited on the devices from other manufacturers or on a PC, or if it has far too many titles, or if there is very little available capacity remaining on the disc.

● DVD-RAM discs recorded on this unit cannot be played back on

an incompatible DVD player.

● It is possible to record copy-once programs of digital broadcasts

only onto 4.7/9.4 GB DVD-RAM discs (2.8 GB DVD-RAM discs are not compatible).

DVD-RW

12 cm: 4.7 GB/9.4 GB Ver. 1.1/1x – 2x speed (Video mode/VR mode) Ver. 1.2/4x speed (Video mode/VR mode)

DISC INFORMATION

EN 7

DVD-R/RW Discs

It is only possible to use DVD-R discs which conform with DVD-R standard Version 2.0. When a DVD-R/RW disc (Video mode) is finalized (A pg. 75), it can be played back on a standard DVD player as a DVD VIDEO disc. When a DVD-RW disc (VR mode) is finalized (A pg. 75), it can be played back on a standard DVD player compatible with the VR mode of DVD-RW discs.

Before finalizing ^ ^ it is possible to record on unrecorded areas of the disc, edit the

disc title and program titles, and delete programs.

● It is impossible to record or edit DVD-R/RW discs recorded on

other devices even if they have not been finalized.

● It is impossible to overwrite recorded areas of DVD-R discs.

● Available recording capacity does not increase even if a recorded

program is deleted from a DVD-R disc.

After finalizing ^

After a DVD-R/RW disc (Video mode) has been finalized, it is possible to play back the recorded programs (video and/or audio) on a standard DVD video player as a DVDVIDEO disc.

● Edited titles are displayed as the

ADVD menuB in video mode.

● It is impossible to record, edit or

delete the data either in video mode or in VR mode.

● Either in video mode or in VR

mode, although the disc can be

HOME MOVIES DOCUMENTARIES

MTV CARTOON

TRAVELLING CLIPS

played back on DVD players from other manufacturers, sometimes it may not be possible to play back depending on the disc and recording conditions.

● It is impossible to record on CD-R/RW or DVD-R discs used for

authoring.

● It is impossible to record onto DVD-R/RW (Video mode) discs

broadcasts that allow you to copy once. The copy once programs can only be recorded onto DVD-RW discs formatted in VR mode.

NOTES:

● The following may result if you play back a DVD-R disc recorded

on another unit.

● The disc does not play.

● A mosaic pattern (block noise) appears on the screen.

● Video or audio may be dropped out.

● The unit stops during playback.

● 6x speed DVD-RW disc cannot be used on this unit.

8 EN

DISC INFORMATION

Discs For Playback Only

You can use discs with the following logos for playback only.

DVD VIDEO Video CD/Super Video CD

(example of region code indications)

Audio CD

CD-DA files

CD-RW

CD-DA/JPEG/ MP3/WMA files

● Playback may not be performed depending on the characteristics

and condition of the disc used.

● DTS Audio CDs can also be played back (An optional DTS

decoder is required).

● MP3 and JPEG discs can be played back on this unit only when

they have been recorded in the ISO9660 or Joliet format and finalized.

● JPEG files that can be played back on this unit must conform to

JFIF/Baseline process, and the maximum resolution of a JPEG file is 2,812 pixels in width and 2,112 pixels in height.

● CD-R/RW discs recorded in music CD format need to be finalized

to play back on this unit.

● Operation and audio quality of this unit are not guaranteed for

discs that do not conform to the Compact Disc specification (CD-DA). Before you play back a CD, check for the CD logo and read the notes on the package to confirm that it conforms to the Compact Disc specification.

● Depending on the intentions of the author of the software,

recording conditions of DVD discs and Video CD/SVCD discs may be restricted. Since this unit plays back discs according to the intentions of the author of the software as indicated on the disc, some functions may not operate as commanded.

● When switching from the first layer to the second layer of double-

layered DVD VIDEO discs, the image and sound may be momentarily distorted. This is not a malfunction.

● DVD-AUDIO discs compatible with DVD video players can be

played.

● Super Audio CDs (SACD) compatible with conventional CD

players can be played.

CD-R

CD-DA/JPEG/ MP3/WMA files

CD-ROM

JPEG/MP3/ WMA files

Unplayable Discs

The following types of discs cannot be played using this unit. Do not attempt to play back any kind of disc that is damaged (cracked, warped, or repaired with adhesive tape) or discs in unusual shapes (heart-shaped, octagonal, or other forms). If such discs are accidentally played back, it may cause noise that can lead to speaker damage.

● CD-ROM discs (including PHOTO-CD and CD-G)

● Discs recorded in Packet Write (UDF) format

● 1.3-GB double density CDs (DDCD)

● High density CDs (HDCD)

The following discs also cannot be played back.

● Discs of a region number other than A1B

● DVD-RAM (2.6 GB/5.2 GB)

● DVD-RAM (TYPE1)

Caution for DualDisc playback

The Non-DVD side of a ADualDiscB does not comply with the ACompact Disc Digital AudioB standard. Therefore, the use of Non-

DVD side of a DualDisc on this product may not be recommended.

Region Number

The world is divided into 6 regions for DVD VIDEO discs. DVDVIDEO discs are assigned a region number to indicate which region they may be played back in. A disc cannot be played back on this unit unless the region number of the disc matches that of the unit. The region number for this unit is A1B. Only discs whose region number includes A1B or AALLB can be played back such as shown below.

Examples of DVD VIDEO labels which can be played back using this unit.

Marks of discs in this instruction manual

Allows operation with a DVD-RAM disc.

Allows operation with a DVD-R disc.

Allows operation with a DVD-RW disc.

Allows operation with a DVDVIDEO disc.

Allows operation with a Video CD/Super Video CD (SVCD) disc.

Allows operation with an Audio CD disc.

Allows operation with a disc including MP3 files.

Allows operation with a disc including JPEG files.

Recording Medium And Format

DVD-RAM

● Recording and erasing can be performed as many times as

possible on a disc.

● Editing can be performed after recording, such as deleting

unwanted parts.

● While recording, it is possible not only to start playback of a

program currently being recorded, but also to watch another program previously recorded.

DVD-RW (VR mode)

● Recording and erasing can be performed as many times as

possible on a disc.

● Editing can be performed after recording, such as deleting

unwanted parts.

DVD-RW (Video mode)

● Can be played back on other DVD players.

● New recording can be performed by erasing all the data on a disc

once played back.

DVD-R

● Can be played back on other DVD players.

● Suitable when keeping a recorded disc for a long time.

File Structure Of Discs

DVD VIDEO

Typically, DVD VIDEO discs are made up of larger units called AtitlesB. Each title has a number (title number) that can be used to select desired titles. Titles are further divided into units called AchaptersB. Each chapter has a number (chapter number) that can also be used to select desired chapters. Note that some discs are not divided into titles and chapters.

When you record a program on a DVD-RAM/RW (VR mode) disc

A single recording session results in a single title (a single chapter). However, chapter marks are automatically inserted when recording is paused, or audio changes from monaural to stereo due to commercial breaks, etc. It is also possible to insert chapter marks at desired locations during playback. (A pg. 27)

When you record a program on a DVD-R/RW (Video mode) disc

A single recording session results in a single title (a single chapter). However, chapter marks are automatically inserted when recording is paused, or audio changes due to commercial breaks, etc. It is also possible to insert chapter marks at desired locations during either recording or playback. Once the disc has been finalized, these chapter marks are deleted and new chapter marks are assigned automatically approximately every 5 minutes.

DVD-RAM, DVD-RW, DVD-R or DVD VIDEO disc

Title 1 Title 2

Chapter 1 Chapter 2

● In Video mode, even before finalizing, it is impossible to perform

Chapter 3

editing operations other than changing the disc name and/or title names and deleting programs and/or titles.

● After finalizing, it is impossible to perform editing operations.

Chapter 1

Chapter 2

Chapter 3

DISC INFORMATION

EN 9

Audio CD/Video CD/SVCD

Typically, Audio CD discs are divided into separate tracks each containing one song. Each track is assigned a number. For example, the third track is Track 3. The same is true for Video CD/ SVCD discs. However, some discs are not divided into tracks.

Audio CD or Video CD/SVCD

Track 1 Track 2 Track 3 Track 4

JPEG/MP3 Disc (CD-R/RW/ROM)

MP3/JPEG files put in directories nested in several levels on a disc will be organized as if they were put in single level directories (groups) by the MP3/JPEG Navigation of this unit. (A pg. 56)

File structure of a disc before starting the MP3/JPEG Navigation

Directory MP3 file JPEG file

File structure of the disc after starting the MP3/JPEG Navigation

Files are automatically grouped as follows and displayed on the MP3/JPEG Navigation screen. Data is displayed in the alphabetical order of file name. Files are grouped based on roots.

● This unit can recognize up to 9 hierarchies including directories

and files. Also, it can recognize up to 250 files in each group, and up to 99 groups on a disc.

NOTES:

● Video CD/SVCD discs that support Playback Control (PBC)

The contents of a disc are recorded into several hierarchies, and played back according to the instructions on the screen while navigating through the hierarchies. It is also possible to playback recorded tracks consecutively without activating the PBC function even when playing a PBC-compatible disc. (A pg. 28)

● Regarding the contents recorded on discs

Some files may not be played back depending on the file types and other factors.

10 EN

DV/HDD/DVD

DVD–

DVIN/ OUT

INSERT

SELECT

A.DUB RECMODE

DISC INFORMATION

DVD VIDEO Marks

Sometimes marks are printed on a DVD disc and/or on its packaging to indicate information regarding the contents and functions of the disc. Check the marks indicating the contents and functions of the disc. Note, however, that in some cases a disc may not include a mark even for a function it supports.

Marks related to video

Number of subtitles Number of angles

Recorded under the standard 4:3 aspect ratio

Video playback is in Wide video mode (16:9) on wide televisions, but in letter box on televisions with standard 4:3 aspect ratio.

Video playback is in Wide video mode (16:9) on wide televisions, but pan and scan is used on televisions with standard 4:3 aspect ratio (either the left or right side of the image is cut-out).

Marks related to audio

Number of audio tracks

Screen includes black bands at the top and the bottom of image which has a standard 4:3 aspect ratio (letter box)

Placing A Disc

Opening the disc tray

Press M to open the disc tray.

● Pressing the button again closes the disc tray.

● Use the button to open and close the disc tray.

● Do not block the disc tray with your hand while it is opening or

closing as this may result in hardware failure.

● Do not place unplayable discs or any object other than a disc on

the disc tray.

● Do not press down strongly on the disc tray or place any heavy

objects on it.

Discs without cartridges

Dolby Digital mark It has been developed by Dolby Laboratories as a digital surround system.

DTS (Digital Theater Systems) You can enjoy DTS audio if you connect an amplifier with a built-in DTS decoder to the DIGITAL OUT connector of the unit.

Disc tray

Place the disc on the disc tray with the label side facing up. Since disc size changes depending on the disc to be played back, be sure to correctly align the disc with the grooves for its size. If the disc is not in its groove, it may be scratched or otherwise damaged. To insert an 8 cm disc, place it according to the inner groove.

DVD-RAM discs contained in cartridges

Double-sided discs:

Remove the disc from the cartridge. Align the disc with the grooves on the disc tray as shown in the illustration and insert with the side you wish to play back or record facing down. If you insert the disc with ASide AB facing down, programs are recorded on the side A.

Single-sided discs:

Remove the disc from the cartridge. Align the disc with the grooves on the disc tray as shown in the illustration and insert with the label side facing up.

Care And Handling Of Discs

How to handle discs

When handling a disc, do not touch the surface of the disc. Since discs are made of plastic, they are easily damaged. If a disc gets dirty, dusty, scratched or warped, the images and sound will not be picked up correctly, and such a disc may cause the unit to malfunction.

Label side

Do not damage the label side, stick paper to or use any adhesives on its surface.

Recording side

Make sure that discs are not scratched or dirty on the recording side before use. Scratches and dirt on the recording side of a disc may hinder proper playback and recording. Also be careful that a DVD-RAM disc may get scratched or dirty when removed from cartridge then put back in after use.

Storage

Make sure that discs are kept in their cases. If discs are piled on top of one another without their protective cases, they can be damaged. Do not put discs in a location where they may be exposed to direct sunlight, or in a place where the humidity or temperature is high. Avoid leaving discs in your car!

DISC INFORMATION

EN 11

Maintenance of discs

If there are fingerprints or other dirt adhering to a disc, wipe with a soft dry cloth, moving from the centre outwards. If a disc is difficult to clean, wipe with a cloth moistened with water. Never use record cleaners, petrol, alcohol or any anti-static agents.

CAUTION:

Sometimes during playback, noise may appear or images may be garbled. This is sometimes due to the disc. (It may not be up to industry standards.) These symptoms are caused by the discs, not by the malfunction of the unit.

12 EN

INDEX

Front View

STANDBY/ON

S-VIDEO VIDEO

(MONO)

L–AUDIO–R

F–1

LOPQRSTV

A Eject Button (M) (DV) A pg. 41

● This button functions even if this unit is turned off.

B Mini DV Cassette Loading Slot C DV Lamp (DV) A pg. 41

DV Recording Lamp (R)

D HDD Lamp (HDD) A pg. 20, 37

HDD Recording Lamp (R) A pg. 37

E Open/Close Button (M) (DVD) A pg. 10

● This button functions even if this unit is turned off.

F DV/HDD/DVD Select Button (DV/HDD/DVD SELECT)

A pg. 24, 37, 41

● This button will not function during navigation mode or set up

mode.

G Stop Button (o) A pg. 24, 39 H Disc Tray I Reverse Search Button (O) (HDD & DVD deck) A pg. 25,

44 Rewind Button (O) (DV deck) A pg. 41, 42

J Forward Search Button (N) (HDD & DVD deck) A pg. 25,

44 Fast Forward Button (N) (DV deck) A pg. 41, 42

DV– HDD – DVD–

INSERT

FEGHIJBA

DV/HDD/DVD

SELECT

A.DUB RECMODE

DVIN/ OUT

WXNM

K STANDBY/ON Button (A) L S-video Input Connector [S-VIDEO] A pg. 62 M Video/Audio Input Connectors

[VIDEO/AUDIO ((MONO) L/R)] A pg. 62

N Channel Buttons (CH +/–) A pg. 34, 37 O Front Display Panel A pg. 14 P DVD Lam p (DVD) A pg. 20, 24

DVD Recording Lamp (R) A pg. 34

Q Infrared Beam Receiving Window R Insert Button (INSERT) A pg. 66 S Audio Dubbing Button (A.DUB) A pg. 65 T Recording Mode Button (REC MODE) A pg. 34, 37 U Play Button (I) A pg. 24, 39 V Record Button (R) A pg. 34, 37 W Pause Button (W) A pg. 24, 39 X DV Input/Output Connector [DV IN/OUT(A*)] A pg. 60

● [DV OUT] is available for DV deck only.

* A (i.Link) refers to the IEEE1394-1995 industry specification and

extensions thereof. The i.Link standard.

A logo is used for products compliant with the

To access covered connectors, pull and open the cover.

Rear View

INDEX

EN 13

ACDB

A Region Number A pg. 8 B AC Power Cord A pg. 18 C Cooling Fan

● This prevents the temperature from rising inside the unit.

Do not remove it.

● Install the unit so as not to block the area around the fan.

● The unit may become hot when it is turned off, as the cooling

fan on the rear of the unit is not activated. However, the cooling fan may be activated in the following cases;

^ When AAUTO CLOCKB is set to AONB. (A pg. 21)

(Set AAUTO CLOCKB to AOFFB if you mind the noise of the fan.)

D Component Video Output Connectors [COMPONENT

VIDEO OUT (Y/P

B/PR

)] (HDD & DVD deck only) A pg. 18

E GF

S VIDEO

COMPONENT

VIDEO OUT

PCM/ STREAM

COAXIAL

HDD/DVD

DIGITAL

AUDIO OUT

OPTICAL

VIDEO

AUDIO

OUTPUT HDD/DVD

VIDEO

AUDIO

INPUT L-1

DV/HDD/DVD

S VIDEO

VIDEO

AUDIO

OUTPUT

E S-VIDEO/VIDEO/AUDIO OUTPUT Connectors (HDD & DVD

deck only)

● These connectors only output DVD/HDD signal and can be

used to connect to a second monitor.

F S-VIDEO/VIDEO/AUDIO INPUT Connectors (L-1) A pg. 63 G S-VIDEO/VIDEO/AUDIO OUTPUT Connectors (DV, HDD &

DVD deck) A pg. 18, 63

H Antenna Input Connector [ANTENNA IN] A pg. 18 I Digital Audio Output Connectors

[DIGITAL AUDIO OUT (OPTICAL/COAXIAL)] (HDD & DVD

deck only) A pg. 64, 69 J Antenna Output Connector [ANTENNA OUT] A pg. 18

ANTENNA

OUT

14 EN

INDEX

Front Display Panel

ABC FEDHGI

LPCM FR XP SP LP EP

RW VCD

RAM

A Disc Type Indicator

When a disc is loaded, the type of the disc is indicated.

Disc Status Indicator

When a disc is running, the disc marks rotate.

VR Mode Indicator (VR) A pg. 74

Lights when a DVD-RW disc is formatted in VR mode.

B Linear PCM Indicator (LPCM)

Lights when AXP MODE REC AUDIOB is set to ALINEAR PCMB (A pg. 71) for recording with HDD, DVD-RAM, DVD-R and DVD-RW discs, and when Linear PCM audio is played.

C Cassette Loaded Mark (u)

Indicates the present of a cassette in the DV deck. Lights when a cassette is loaded into the DV deck. It will remain lit as long as the cassette is loaded, even if the HDD or DVD deck is being selected.

D Recording Mode Indicator (XP/SP/LP/EP/FR) A pg. 34

Blinks when recording mode is being set. While AFRB is blinking, the left 3 digits of the Multi Display (L N) indicate setting values ranging from A60B to A480B. After the value has been set, only AFRB lights.

E Group/Title Indicator (GRP/TITLE)

AGRPB or ATITLEB lights depending on a disc loaded while the left 2 digits of the Multi Display (L) indicate the numbers explained below.

AGRPB: Total number of groups or group number being played

ATITLEB: Total number of titles or title number being played

F Channel Indicator

Indicates the channel received.

G Track/Chapter Indicator (TRK/CHAP)

ATRKB or ACHAPB lights depending on a disc loaded while the 3rd and 4th digits from the left of the Multi Display (N) indicate the numbers explained below.

ATRKB: Total number of tracks or track number being played

ACHAPB: Chapter number being played back are displayed on

H Simulated Surround Effect Indicator (3D) A pg. 31

Lights when a simulated surround effect is set to A3D-ONB on the on-screen bar.

back are displayed on the Multi Display.

the Multi Display.

I Random/Program Playback Mode Indicator (RND/PRGM)

A pg. 32

ARNDB: Lights when Random Playback mode is set.

APRGMB: Lights when Program Playback mode is set.

J Repeat Mode Indicator (x/1/A-B) A pg. 29

Select Repeat Playback mode on the on-screen bar.

AxB: Whole disc is played back repeatedly.

Ax1B: A single title/chapter/track is played back

AxA-BB: The selected part (A-B) is played back repeatedly.

No display: Repeat Playback mode is off.

K Video Output Indicator (q) A pg. 76

No display: Indicates that interlace mode is engaged.

q: Indicates that progressive mode is engaged.

(Example) q lights when video output mode is in progressive

L Group/Title Number Display M Audio Dubbing/Insert Editing Indicator

AADUBB or AINSB lights up during Audio Dubbing or Insert

Editing respectively.

N Track/Chapter Number Display O Remaining Time/Elapsed Time Indicator A pg. 27, 35

Lights when remaining time of HDD, DVD-RAM, DVD-R and

DVD-RW discs is displayed, and lights out when elapsed time is

displayed.

The right 6 digits of the Multi Display (P) indicate elapsed or

remaining time of each track.

No display: Indicates elapsed time of the disc.

Displayed: Indicates remaining time of the disc.

P Remaining Time/Elapsed Time Display A pg. 27, 35

Time Code Display A pg. 42 Q Multi Display

Displays clock, received channel, elapsed time, and remaining

time.

Also displays status of the unit (NO DISC/OPEN/CLOSE/

READING).

repeatedly.

mode.

Remote Control

CABLE/DBS

DVD

B C

VIDEO

DV HDD DVD

TV/

STANDBY/ON

TV/CBL/DBS

DVD

TV VOL

AUX

F G

CANCEL

LIVE

TV MUTING

MEMO/MARK

EDITDUBBING

PROG

H I J

NAVIGATIONTOP MENU

ENTER

RETURN

NEXTPREVIOUS

SLOWSLOW PLAY/SELECT

CLEAR

STOP/

JUMP

PAUSEREC

REC MODE

DISPLAY

ON SCREEN

ANGLE

SET UP

PROGRESSIVE

SCAN

P Q

REMAIN

AUDIO

SUBTITLE

R S

A TV/VIDEO Button* A pg. 67

* Not function with this unit. This button functions with TV.

B DV Button* A pg. 41

* This button will not function during navigation mode or set up mode.

C HDD Button* A pg. 37

* This button will not function during navigation mode or set up mode.

D Number Keys A pg. 34, 37 E Cancel Button (CANCEL(L)) A pg. 32 F Auxiliary Button (AUX): Switches the AV source to AL-1B. G Live Button (LIVE) A pg. 44 H Dubbing Button (DUBBING) A pg. 57

TV Muting Button (TV MUTING) A pg. 67

I Top Menu Button (TOP MENU) A pg. 25 J Selection Keys (FGD E) A pg. 20 K Menu Button (MENU) A pg. 25 L Reverse Skip Button (S) A pg. 25, 44, 40

Previous Button (PREVIOUS) A pg. 28

M Reverse Search Button (O) (HDD & DVD deck) A pg. 25,

44 Rewind Button (O) (DV deck) A pg. 41 Reverse Slow Button (SLOW –) A pg. 25

N Record Button (R) A pg. 34, 37 O Jump Button (JUMP +/–) A pg. 40 P Recording Mode Button (REC MODE) A pg. 34, 37

Remain Button (REMAIN) A pg. 27, 35

LIVE CHECK

T U

V W

Z a

b c

d e

g h

i j k l

m n

INDEX

EN 15

Q Display Button (DISPLAY) A pg. 27, 35, 42 R Audio Button (AUDIO) A pg. 28 S Subtitle Button (SUBTITLE) A pg. 28 T TV/CABLE/DBS/DVD switch A pg. 20, 67, 68 U DVD STANDBY/ON Button (DVD A) V TV/CBL/DBS STANDBY/ON Button (TV/CBL/DBS A)

A pg. 67 W DVD Button* A pg. 24

* This button will not function during navigation mode or set up mode.

X TV Volume Buttons (TV VOL +/–) A pg. 67 Y Channel Buttons (CH +/–) A pg. 34, 67 Z Memo Button (MEMO) A pg. 51, 54

Mark Button (MARK) A pg. 27

a Programming Button (PROG) A pg. 46, 48, 49 b Edit Button (EDIT) A pg. 51 c Navigation Button (NAVIGATION) A pg. 50, 56 d Enter Button (ENTER) A pg. 20 e Return Button (RETURN) A pg. 28, 30, 46 f Forward Skip Button (T) A pg. 25, 44

Next Button (NEXT) A pg. 28 g Forward Search Button (N) (HDD & DVD deck) A pg. 25,

Fast Forward Button (N) (DV deck) A pg. 41

Forward Slow Button (SLOW +) A pg. 25 h Play Button (I) A pg. 24, 39

Select Button (SELECT) A pg. 56

i Pause Button (W) A pg. 24, 39 j Stop Button (o) A pg. 24, 39

Clear Button (CLEAR

) A pg. 32

k Skip Search Button (v) A pg. 26, 39, 42, 44 l Set Up Button (SET UP) A pg. 20, 70 m One Touch Replay Button (w) A pg. 26, 40, 42, 44, 45 n On-Screen Button (ON SCREEN) A pg. 16, 29 o Progressive Scan Button (PROGRESSIVE SCAN) A pg. 76 p Angle Button (ANGLE) (DVD deck only) A pg. 27

Live Check Button (LIVE CHECK) A pg. 44

How To Use

Before use, insert two AA size batteries into the remote control with the polarity (F and G) matched correctly as indicated on the battery compartment or on the lid.

The remote control can operate most of your unit’s functions, as well as basic functions of TV sets of JVC and other brands. (A pg. 67)

● Point the remote control toward the receiving window.

● The maximum operating distance of the remote control is

about 8 m.

NOTE:

If the remote control doesn’t work properly, remove its batteries, wait a short time, replace the batteries and then try again.

16 EN

7: 00 XP 10: 00 SP 20: 00 LP 28: 00

36: 00

FR480

ITR 2 : 30

INDEX

On-Screen Display (HDD & DVD deck)

When ASUPERIMPOSEB is set to AAUTOB and ON SCREEN on the remote control is pressed, various operational indicators appear on the TV screen. To clear the operational indicators, press ON SCREEN twice.

When playing back a recorded title HDD

0:00 1:00 2:00

FISHING WORLD

01:16:48 FR360

Digital

When pressing REC MODE

(Appears for eight seconds.)

A Remaining disc time for each recording speed B Recording speed

When pressing R during recording

A Title start B Current playback point C Title end D Elapsed playing time E Play mode F Name of title currently being played back G Time scale (This title is an hour and a half long.) H Audio mode

DVD

TITLE99 CHAPTER999 REMAIN6:59:59T.

FISHING WORLD

Digital

A Playback title number B Playback chapter number C Disc remaining time D Current status (playback) E Audio mode F Bar meter G Name of title (or play list) currently being played back H Current playback point I Recorded mode*

* Depending on the recording condition, the recorded mode may not

always be displayed.

When recording HDD

A Recording time for Instant Timer Recording (ITR) mode

When using Live Memory playback HDD

11:00 12:00 13:00

FR360

11:35AM

11:33AM

PR.12

DVD

TITLE99 CHAPTER999 REMAIN6:59:59 T.

RAM

FR360

11:35AM

11:33AM

PR.12

A Time scale for recording (HDD deck)

Bar meter for recording (DVD deck)

B Current recording point C Recording mode D Current time E Current playback channel position number F Time scale for Live Memory Playback (HDD deck)

Bar meter for Live Memory Playback (DVD deck)

G Current playback point H Live Memory playback mode I Current playback time

11:00 12:00 13:00

FR360

DVD

TITLE99 CHAPTER999 T. REMAIN6:59:59

RAM

FR360

A Recording point B Current status (recording) C Current time D Recording channel number

11:35AM

PR.12

LIVE

PR.12

LIVE

INDEX

SE CL EANI NG C ASSETT E

61BIT

R000:00:00:

G F

A B

EN 17

On-Screen Display (DV Dubbing)

When capturing images from the external DV equipment

0:00 1:00 2:00

HDD

00: 00 : 00. 00

FR360

12bit

JVC

GR-DV3500DV

A Recording speed B HDD capacity graph C HDD time counter D Recording time scale E HDD mode F Remote control mode G Connected DV equipment mode H Connected DV equipment model information I Input channel J Sound mode K Sound input bit-rate*

* Indicates the sound bit-rate of the connected DV equipment

L Connected DV equipment information*

* Maker name and model name, etc. may not appear depending on the

connected equipment.

M Time counter for the connected DV equipment N Sound monitor mode

DV DV

O Remote control switch P Auto capture button Q Sound monitor switch

GR-DV3500

00: 00 : 00. 00

SOUND1

1 2

On-Screen Display (DV deck)

When ASUPERIMPOSEB is set to AAUTOB and ON SCREEN on the remote control is pressed, various operational indicators appear on the TV screen. To clear the operational indicators, press ON SCREEN again.

A Operation Mode Indicators B Tape Speed (SP/LP) C Sound Mode Display A pg. 71 D Current Month/Day/Year/Clock Display/Time Code Display

A pg. 42

E Audio Mode Display A pg. 42 F Warning Message G Auxiliary Input Indicator (L-1, F-1 or DV) H ACassette LoadedB Mark

R Elapsed recording time

179 : 59 : 59

18 EN

INSTALLING YOUR NEW UNIT

Basic Connections

Antenna or Cable

AC outlet

Back of unit

[COMPONENT

VIDEO OUT

(Y/P

Component

video cable

(not supplied)

Flat feeder

AC power cord

B/PR

)]

To [S-VIDEO

S-video cable (not supplied)

Coaxial cable

OUTPUT]

Matching transformer (not supplied)

[AUDIO/

VIDEO

OUT]

Audio/Video

cable

(supplied)

To [ANTENNA IN]

To [ANTENNA OUT]

RF cable (supplied)

8 S-Video Connection To connect to TV’s S-VIDEO input and AUDIO input connectors ^

A Perform A – C of AAV ConnectionB in the left column. B Connect the unit’s [S-VIDEO OUTPUT] connector to the TV’s

S-VIDEO input connector.

C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s

AUDIO input connectors.

● If your TV is not stereo-capable, use the unit’s [AUDIO

OUTPUT] connectors to connect to an audio amplifier for Hi-Fi stereo sound reproduction.

NOTE:

During DV playback, signal is output only from the connectors marked DV/HDD/DVD.

8 Component Video Connection To connect to TV’s component video input connectors ^

A Perform A – C of AAV ConnectionB in the left column. B Connect the unit’s [COMPONENT VIDEO OUT (Y/P

B/PR

)]

connectors to the TV’s component video input connectors.

C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s

AUDIO input connectors.

● You can obtain high-quality component video pictures.

● The [COMPONENT VIDEO OUT (Y/P

B/PR

)] connectors do not

output DV signals.

● If your TV is not stereo-capable, use the unit’s [AUDIO

OUTPUT] connectors to connect to an audio amplifier for Hi-Fi stereo sound reproduction.

● By using the component video connection, you can view the

images in the progressive mode. For switching to the progressive mode, refer to AScan Mode Set (HDD & DVD Deck Only)B (A pg. 76).

It’s essential that your unit be properly connected.

ATTENTION:

Connect the AC plug only after all connections to the TV has been completed.

THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.

1 Make sure the package contains all of the accessories listed in

ASPECIFICATIONSB (A pg. 84).

2 Place the unit on a stable, horizontal surface. 3 Connect the unit to a TV depending on the TV and cables you

use.

8 AV Connection To connect to a TV with AV input connectors ^

A Disconnect the TV aerial cable from the TV. B Connect the TV antenna cable to the [ANTENNA IN] connector

on the rear panel of the unit.

C Connect the [ANTENNA OUT] connector on the rear panel of

the unit and the TV’s antenna connector with the supplied RF cable.

D Connect the supplied Audio/Video cable between the [AUDIO/

VIDEO OUTPUT] connectors on the rear panel of the unit and the TV’s audio/video input connectors.

NOTE:

The [ANTENNA OUT] connector is only used to pass antenna signal to the TV. It is necessary to connect the [AUDIO/VIDEO OUTPUT] connectors to the TV to enjoy audio-visual programs.

4 Plug the end of the AC power cord into an AC outlet.

This unit performs Plug & Play Set automatically. (A pg. 19)

● The clock and tuner channels will automatically be set when the

antenna is connected and when the AC power cord is first connected to an AC outlet. (If AAUTOB and the channel indicator are displayed on the front display panel before the unit is powered on, the clock and tuner channels are being set automatically. Wait for the time to be displayed on the front display panel before turning on the unit.)

● ALOADINGB blinks on the front display panel when the AC

plug of the AC power cord is connected into a AC outlet and it takes approximately 50 seconds for the unit to be turned on. This is not a malfunction.

Plug & Play Set

Auto Clock Set/Auto Tuner Set

This unit sets the clock and tuner channels automatically when AC power cord is first connected to an AC outlet. The antenna cable must be connected for the Plug & Play setting. The time and date can be set automatically by the clock setting data transmitted from one of the regular TV broadcast channels. We call this TV channel the “host channel” and it is a PBS channel in your area.

ATTENTION:

● If you use a cable box, Plug & Play will not function; set the

clock and tuner channels separately. (墌 pg. 21 – 22)

● Depending on areas or reception conditions, the unit may not

receive the Auto clock setting data from the PBS channel. If this function is taking a considerable amount of time, it may be necessary to perform the Semiauto or Manual Clock Set procedure.

INITIAL SETTINGS

EN 19

1 Connect the antenna cable to the unit. (A pg. 18) Then connect

the AC power cord to an AC outlet. Do not turn on the unit. The clock and tuner channels will be set automatically.

● ALOADINGB blinks on the front display panel when the AC

plug of the AC power cord is connected into an AC outlet and it takes approximately 50 seconds for the unit to be turned on. This is not a malfunction.

NOTES:

● Auto Clock Set is performed first.

AAUTOB blinks on the front display panel during Auto Clock Set.

● Auto Channel Set is performed next. Auto Channel Set scans all

the channels that are receivable by your unit. During Auto Channel Set, the channel numbers are displayed as they are scanned and set.

● When Plug & Play setting has been completed successfully, the

correct clock time is displayed. If you perform Plug & Play setting successfully, there is no need to perform AClock SetB (A pg. 21) and ATuner SetB (A pg. 22). If, however, you want to add or delete channels, refer to AManual Channel SetB (A pg. 22).

During Auto Clock Set

AAUTOB blinks.

During Auto Channel Set

The channel numbers are displayed and AAUTOB blinks as they are scanned and set.

INFORMATION

● If AAUTO CLOCKB is set to AONB (A pg. 21), the clock will be

adjusted automatically by the host channel every hour (except 11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming PBS channel clock setting data. (This automatic clock adjustment can only be performed when the unit is turned off. The clock will be adjusted just on these hours — on the time displayed on the front display panel, not on the actual real time.) The default setting of AAUTO CLOCKB is AONB. (A pg. 21)

● If the memory backup fails, because a power outage occurs or

because the AC power cord is unplugged, Plug & Play will be performed when power is restored to the unit.

What to do if Plug & Play setting failed

● If an incorrect time is displayed on the front display panel, you

may be receiving the clock setting data of a PBS channel from an adjacent time zone, or an incorrect PBS channel from a cable TV system. In this case, perform ASemiauto Clock SetB (A pg. 21) or AManual Clock SetB (A pg. 21).

● If AcB appears on the front display panel, your antenna

cable may not be connected to the unit or there may not be a Host PBS signal available in your area. Ensure that the antenna cable is connected correctly. Then turn on and off the unit; the Plug & Play setting will be automatically reactivated. If Plug & Play setting is not performed though the antenna cable is connected correctly, perform AManual Clock SetB (A pg. 21) and AAuto Channel SetB (A pg. 22) or AManual Channel SetB (A pg. 22).

Plug & Play Completed

The current time is displayed.

● If an incorrect clock time or AcB appears on the front display

panel, see AWhat to do if Plug & Play setting failedB on the left column.

20 EN

INITIAL SETTINGS

Language

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

CABLE/DBS

HDD

ENTER

DVD

Selection Keys

FGDE

SET UP

On-screen Language Set

This unit offers you the choice to view on-screen messages in 3 different languages.

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press SET UP to access the Main Menu screen. 3 Press selection keys to select AFUNCTION SET UPB, then

DVDTV

press G.

4 Press selection keys to select

ADISPLAY SETB, then press G.

5 Press selection keys to select

AON SCREEN LANGUAGEB, then press ENTER.

6 Press selection keys to select

your desired language, then press ENTER.

DVD VIDEO SET UP

HDD/DVD/DV SET UP

REC/PLAY SET UP DISPLAY SET

SUPERIMPOSE

BLUE BACK

DIMMER

POWER SAVE

ON SCREEN LANGUAGE

ENTER

SET UP

EXIT

SELECT

FUNCTION SET UP

VIDEO IN/OUT

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

AUTO

BRIGHT

OFF

ENGLISH

INITIAL SET UP

7 Press SET UP to complete the setting.

Menu/Audio/Subtitle Language Set (DVD deck only)

Some DVD discs contain the DVD menu display, audio and subtitles in multiple languages. With these discs, you can set the default language as you like.

● The procedure shows how to set AMENU LANGUAGEB as an

example.

1 Press DVD so that the DVD lamp lights up on the unit. 2 Press SET UP to access the Main Menu screen. 3 Press selection keys to select ADVD VIDEO SET UPB, then

press G.

4 Press selection keys to select

ALANGUAGE SETB, then press

5 Press selection keys to select

AMENU LANGUAGEB, then press ENTER.

6 Press selection keys to select

your desired language, then press ENTER.

● See ALanguage Code ListB (A pg. 81).

7 Press SET UP to complete the setting.

NOTE:

When the selected language is not available on the disc, the disc’s default menu language is played back.

DVD VIDEO SET UP

HDD/DVD/DV SET UP

LANGUAGE SET AUDIO OUTPUT

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ENTER

SET UP

EXIT

SELECT

FUNCTION SET UP

PARENTAL LOCK DISC PLAY SET UP

ENGLISH

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

INITIAL SET UP

Clock Set

Perform clock setting only if the clock has not been set correctly by the Plug & Play setting.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

CABLE/DBS

DVDTV

HDD

ENTER

DVD

Selection Keys

FGDE

SET UP

INITIAL SETTINGS

EN 21

OFF:

Select when Daylight Saving Time does not apply to you.

8 Press selection keys to select ATIME ZONEB, then press

ENTER. Press selection keys to select AAUTOB or the desired time zone, then press ENTER.

● Each time you press FG, the time zone changes as follows:

AUTOYATLANT ICYEASTERNYCENTRALYMOUNTAINY

PACIFICYALASKAYHAWAIIY(back to the beginning)

NOTE:

If an incorrect time is displayed by the Plug & Play function, you may be receiving the clock setting data of a PBS channel from an adjacent time zone or from an incorrect PBS channel from a cable TV system. If you selected AAUTOB for the host channel in step 6, be sure to select the correct time zone manually.

9 Press SET UP to complete the setting.

IMPORTANT

Turn off the unit after performing Semiauto Clock. AAUTOB will appear on the front display panel while the clock is being set. The current clock time will appear automatically when the clock setting is complete.

Auto Daylight Saving Time

This function enables automatic adjustment of the unit’s clock at the start and end of Daylight Saving Time. With Auto DST activated, ^ ^ on the first Sunday of April at 2:00 AM, the clock is adjusted

to 3:00 AM.

^ on the last Sunday of October at 2:00 AM, the clock is

adjusted to 1:00 AM.

NOTE:

Timer recording may not function correctly at the time Daylight Saving Time is adjusted.

Semiauto Clock Set

You can change the host channel/D.S.T. (Daylight Saving Time)/ time zone setting manually.

NOTE:

The time set previously will be erased when AAUTO CLOCKB, AHOST CHB, AD. S. T.B or ATIME ZONEB setting is changed.

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press SET UP to access the Main Menu screen. 3 Press selection keys to select AINITIAL SET UPB, then press

4 Press selection keys to select

ACLOCK SETB, then press G.

5 Press selection keys to select

AAUTO CLOCKB, then press

ENTER. Press selection keys to select AONB, then press ENTER.

6 Press selection keys to select

AHOST CH [CATV]B, then press ENTER. Press selection keys to select AAUTOB or the desired PBS channel number, then press ENTER.

NOTE:

Some PBS channels do not transmit clock setting data.

7 Press selection keys to select AD. S. T.B, then press ENTER.

Press selection keys to select the desired setting, then press ENTER.

AUTO:

Select if you want to adjust your unit’s clock automatically by the incoming signal from the host channel. Be sure to select the correct time zone manually in step 8.

ON:

Adjustment will be made by the built-in clock itself.

DVD VIDEO SET UP

TUNER SET

AUTO CLOCK

HOST CH [CATV]

D. S. T.

TIME ZONE

SET UP

EXIT

HDD/DVD/DV SET UP

ENTER

SELECT

CLOCK SET

FUNCTION SET UP

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

AUTO

INITIAL SET UP

Manual Clock Set

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press SET UP to access the Main Menu screen. 3 Press selection keys to select AINITIAL SET UPB, then press

4 Press selection keys to select

ACLOCK SETB, then press G.

5 Press selection keys to select

AAUTO CLOCKB, then press

ENTER. Press selection keys to select AOFFB, then press ENTER.

6 Press selection keys to select

ATIMEB , then press ENTER. Press selection keys until the desired time appears, then press ENTER to start clock.

● Set the date and year in the same way.

● Holding FG changes the time in 30-minute intervals, or

changes the date in 15-day intervals.

7 Press selection keys to select AD. S. T.B, then press ENTER.

Press FG to select the desired setting, then press ENTER.

ON:

Adjustment will be made by the built-in clock itself.

OFF:

Select when Daylight Saving Time does not apply to you.

8 Press SET UP to complete the setting.

DVD VIDEO SET UP

TUNER SET

AUTO CLOCK

HOST CH [CATV]

D. S. T.

TIME ZONE

SET UP

EXIT

DVD VIDEO SET UP

TUNER SET

AUTO CLOCK

TIME

DATE

YEAR

D. S. T.

SET UP

EXIT

HDD/DVD/DV SET UP

ENTER

SELECT

HDD/DVD/DV SET UP

ENTER

SELECT

CLOCK SET

FUNCTION SET UP

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

FUNCTION SET UP

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

AUTO

––:––

1/1(SAT)

2005

OFF

INITIAL SET UP

22 EN

INITIAL SETTINGS

Tuner Set

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

CABLE/DBS

DVDTV

HDD

0-9

ENTER

INFORMATION

The unit selects the correct mode (TV or CATV) automatically during Auto Channel Set. The selected mode (TV or CATV) will be displayed on the right side of ABANDB on the Manual Tuner Set screen.

Auto Channel Set

Perform Auto Channel Set only if channels have not been set correctly by the Plug & Play setting.

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press SET UP to access the Main Menu screen. 3 Press selection keys to select AINITIAL SET UPB, then press

4 Press selection keys to select

ATUNER SETB, then press G.

0-9

DVD

Selection Keys

FGDE

SET UP

DVD VIDEO SET UP

TUNER SET

HDD/DVD/DV SET UP

CLOCK SET

AUTO CH SET

FUNCTION SET UP

MANUAL CH SET

INITIAL SET UP

Manual Channel Set

You can add the channels you want or delete the channels you do not want manually.

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press SET UP to access the Main Menu screen. 3 Press selection keys to select AINITIAL SET UPB, then press

ENTER.

4 Press selection keys to select ATUNER SETB, then press G. 5 Press selection keys to select AMANUAL CH SETB, then press

ENTER.

6 Press selection keys to select ABANDB, then press ENTER.

Press selection keys to select either ATVB or ACATVB, then press ENTER.

7 Add or skip the desired

channels.

To add channels A Press selection keys to select

ACHB, then press ENTER.

B Press the number keys to

enter a channel number you want to add, then press ENTER.

C Press selection keys to select AADD/SKIPB, then press

ENTER.

D Press selection keys to select AADDB, then press ENTER. E Repeat B – D to add other channels.

To skip channels

A Press selection keys to select ACHB, then press ENTER. B Press selection keys to select a channel number you want to

skip, then press ENTER.

C Press selection keys to select AADD/SKIPB, then press

ENTER.

D Press selection keys to select ASKIPB, then press ENTER. E Repeat B – D to skip other channels.

8 Press SET UP to complete the setting.

INITIAL SET UP > MANUAL CH SET

BAND

ADD/SKIP ADD

ENTER

SET UP

EXIT

SELECT

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

CATV

RETURN

GUIDE CH SET

ENTER

5 Press selection keys to select

AAUTO CH SETB, then press

SET UP

EXIT

INITIAL SET UP > AUTO CH SET

SELECT

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

ENTER. You can automatically set the receivable channels in your area in the order of their frequencies.

● When Auto Channel Set is

complete, ASCAN COMPLETEDB appears on the

SET UP

EXIT

ENTER

SELECT

AUTO CHANNEL SET

SCANNING...

CANCEL

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

TV screen.

● If the scan was unsuccessful, ASCAN COMPLETED –NO

SIGNAL–B appears on screen. Check the connections and start again.

6 Press SET UP to complete the setting.

Monitor Set

You can select the monitor type depending on the TV used when you play back DVD VIDEO discs recorded for wide-screen TVs.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

CABLE/DBS

DVDTV

DVD

INITIAL SETTINGS

EN 23

1 Press DVD so that the DVD lamp lights up on the unit. 2 Press SET UP to access the Main Menu screen.

● You cannot set the monitor type during recording or playback.

3 Press selection keys to select AFUNCTION SET UPB, then

press G.

4 Press selection keys to select

AVIDEO IN/OUTB, then press

5 Press selection keys to select

AMONITOR TYPEB, then press

DVD VIDEO SET UP

REC/PLAY SET UP

MONITOR TYPE

FRONT AUX F-1

REAR AUX L-1

HDD/DVD SET UP

DISPLAY SET

FUNCTION SET UP

VIDEO IN/OUT

4:3LB

VIDEO

INITIAL SET UP

ENTER.

ENTER

6 Press selection keys to select

the desired option, then press

SET UP

EXIT

SELECT

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

ENTER.

7 Press SET UP to complete the setting.

*The boldface settings below indicate the settings at your purchase.

ENTER

Selection Keys

FGDE

SET UP

8 MONITOR TYPE - 4:3LB / 4:3PS / 16:9AUTO / 16:9FIX

4:3LB (Letter Box conversion):

Select this when the aspect ratio of your TV is 4:3 (conventional TV). While viewing a wide screen picture, the black bars appear on the top and the bottom of the screen.

4:3PS (Pan&Scan):

Select this when the aspect ratio of your TV is 4:3 (conventional TV). While viewing a wide screen picture, the black bars do not appear; however, the left and right edges of the pictures will not be shown on the screen.

16:9AUTO (Wide television conversion):

Select this when the aspect ratio of your TV is 16:9 (wide TV).

16:9FIX (Wide television conversion):

Select this when the aspect ratio of your TV is fixed to 16:9 (wide TV). The unit automatically adjusts the screen width of the output signal correctly when playing back a picture whose aspect ratio is 4:3.

Pan&Scan/Letter Box

In general, DVDVIDEO disc are produced for a wide-screen TV with 16:9 aspect ratio. Material with this ratio will not fit to a TV with 4:3 aspect ratio. There are two styles to display the image, APan&ScanB (PS) and ALetter BoxB (LB).

Pan&Scan

The right and left side of the image are cut off. The image fills the screen.

● The picture will be shown in the A4:3LBB mode

depending on the disc even if the A4:3PSB mode is selected.

Letter Box

Black bands appear at the top and bottom of the image. The image itself appears in 16:9 aspect ratio.

24 EN

BASIC OPERATIONS ON DVD DECK

Basic Playback

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

DV/HDD/DVD

SELECT

DVD lamp

DVD

ENTER

CABLE/DBS

To play back an MP3/JPEG disc, see APlayback With MP3/WMA/ JPEG NavigationB (A pg. 56).

1 Load a disc.

● For details, refer to APlacing A DiscB (A pg. 10).

● Pressing I also closes the disc tray.

● Playback begins automatically if an auto-playback DVD disc is

loaded.

2 Press DV/HDD/DVD SELECT on the unit repeatedly or DVD on

the remote control so that the DVD lamp lights up on the unit.

3 Press I to start playback.

DVDTV

● If you load a DVD disc whose region code does not match the

unit, AREGION CODE ERRORB appears on the TV screen. For details, refer to ARegion NumberB (A pg. 8).

● If ACAN NOT PLAY BACK DISC UNDER CURRENT SETTINGB

appears on the TV screen, refer to AParental LockB (A pg. 33).

● With Video CD/SVCD discs with PBC control or some DVD

discs, the menu display may appear on the TV screen after starting playback. In this case, select an item which you want to play back from the menu. Otherwise, the playback cannot go forward. Refer to APlayback Control (PBC) FunctionB (A pg. 28) or ALocating A Desired Scene Using The DVD MenuB (A pg. 25).

● The Library Database Navigation also enables you to search

and select the desired titles. (A pg. 51)

4 Press W to pause playback.

● To resume normal playback, press I.

5 Press o to stop playback.

● When a recordable disc is played, playback stops and a

program received with the unit’s tuner or AV input (from external AV source) resumes on the TV screen.

● When a playback-only disc is played, playback stops and the

TV screen becomes all blue when you press o. Pressing o again resumes a program received with the unit’s tuner.

● If M is pressed during playback, playback stops, then the disc

tray opens.

NOTES:

● When the Library Database Navigation screen appears, choose

a thumbnail image of the desired title on the TV screen, then press ENTER. (A pg. 51)

● It is not possible to playback the DVD disc recorded in 96 kHz on

DVD during recording or Live Memory Playback on HDD.

● It is possible to play back on the DV deck and the HDD/DVD deck

simultaneously. However, either DVD or HDD can be played at the same time.

ATTENTION:

● It takes approximately 30 seconds to read a disc depending on

the type and condition of the disc since this unit is multi-disc compatible (DVD-RAM, DVD-RW, DVD-R). It may even take several minutes when a disc is dirty, scratched or warped.

● It may take a few seconds to start playback. This is not a

malfunction.

● Forward/reverse high-speed search and other operations

cannot be performed while playback is stopped.

BASIC OPERATIONS ON DVD DECK

EN 25

Playback Features

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press DVD so that the DVD lamp lights up on the unit.

CABLE/DBS

DVDTV

DVD

0-9

TOP MENU

ENTER

O/SLOW

JUMP JUMP +

Selection Keys

FGDE

T N/SLOW +

Current playback point

Previous program

Scene 2

(Chapter 2)

Track 2

Reverse

: marked points if any (A pg. 27) or beginning of recording

●

Drama

Scene 3

(Chapter 3)

Track 3

Next program

Scene 4

(Chapter 4)

Track 4

Forward

Movie

Scene 5

(Chapter 5)

Tra c k 5

Variable Speed Search

During playback, press N for forward variable speed search, or O for reverse variable speed search.

● Each press of the button increases the search speed for each

direction.

● To resume normal playback, press I.

For Audio CD

You can perform 4 levels of speed search with N and O. (Audio is active also during variable speed search.) You cannot perform slow motion for each direction.

Locating A Desired Scene Using The DVD Menu

DVDVIDEO discs may have top menu and disc menu.

Top m e nu

DVD discs generally have their own menus which show the disc contents. These menus contain various items such as titles of a movie, names of songs, or artist information. You can locate a desired scene by using the top menu displayed on the TV screen. Press TOP MENU to access the top menu.

Disc menu

Disc menus include playback data (angle menu, subtitle menu, etc.) specific to each title. Press MENU to access the disc menu.

1 Press TOP MENU or MENU to

access the DVD menu.

Example:

2 Press selection keys to select

a desired title, then press ENTER. Playback starts.

● It may be possible to select the

desired item using the number keys depending on the menu

display.

NOTE:

When A7B appears on the TV screen in step 1, the disc does not have a top menu or disc menu.

Locating The Start Point Of The Item Or Skip The Item

Reverse

Reverse Search

4 steps

-60 -15 -3 -113515

Reverse

-5

Play

Reverse

Slow Motion

3 steps

---

Slow Motion

16116

3 steps

Normal

Play

Forward

Forward Search

4 steps

Still Picture/Frame-By-Frame Playback

1 Press W to pause during playback. 2 Press SLOW – (O) or SLOW + (N) to activate frame-by-

frame playback.

● Each press of SLOW – (O) or SLOW + (N) advances/

reverses the still picture frame by frame.

● Frame-by-frame playback for reverse direction cannot be

performed with Video CD/SVCD discs.

● To resume normal playback, press I.

Slow Motion

1 Press W to pause during playback. 2 Press SLOW – (O) or SLOW + (N) for 2 or more seconds.

● Each press of SLOW – (O) or SLOW + (N) increases the

slow motion speed for each direction.

● Slow motion for reverse direction cannot be performed with

Video CD/SVCD discs.

Press S or T during playback.

● Pressing T locates the start point or marked points of the item

or skips the item in the forward direction, then resumes playback.

● Pressing S locates the start point or marked points of the item

or skips the item in the reverse direction, then resumes playback.

26 EN

BASIC OPERATIONS ON DVD DECK

Skip Search

During playback, press v.

● Each press initiates an approximately 30-second period of fast-

motion playback. Normal playback resumes automatically.

● Skip search cannot be performed when a VCD/SVCD disc is

being played back with the PBC function.

One Touch Replay

You can move back the playback position slightly. Press w.

● Each press skips back for approximately 7 seconds and resumes

playback.

● Pressing while paused skips back for approximately 7 seconds

and resumes pause.

Jump Search

You can locate a scene ahead or behind the current one by jumping scenes according to selected time intervals (A pg. 72) during playback (or Live Memory Playback). Press JUMP – or JUMP +.

● To advance forward or back, press JUMP – or JUMP +

repeatedly within 5 seconds of each press to continue jump.

● Depending on the time from where you want to start jump search,

the first press of JUMP – or JUMP + will not necessarily lead to a jump of the selected time interval. The first press will lead to a jump to the nearest quarter points of an hour (15 min/ 30 min/ 45 min/ 00 min). The subsequent jumps will then be in accordance to the selected time interval.

● When you cannot advance any further (beginning or end of

program reached), the message AUNABLE TO GO BACK ANY MOREB appears on the screen and the on-air screen resumes. In such a case, press S, O or o.

Example:

Playback search when jump interval is set to 15 MIN jumps. Taking for instance, you want to start jump search 40 minutes after the beginning of the program. Pressing result in a jump to the scene at the 30 minutes point or 45 minutes point respectively as illustrated below. At the subsequent press, the scene will jump to the 15 minutes point or 1 hour point respectively, according to the selected time interval, which in this case is

Time counter

0 min

Beginning of program

15 min

30 min

Current scene

NOTE:

Jump search cannot be performed with finalized DVD-R/DVD-RW (video mode) discs.

40 min

JUMP –

45 min

JUMP +

1 h 15 min

1 h

End of program

will

15 MINB.

Resume Function

It is possible to memorize the position where you stop playback and resume playback from that position.

● Be sure to set ARESUMEB to AONB or ADISC RESUMEB.

(A pg. 71)

● Resume function always works for DVD-R/DVD-RW discs that

have not been finalized and DVD-RAM regardless of the setting of ARESUMEB.

1 Press o during playback to memorize a resume point.

● The unit enters Resume Stop mode and memorizes the

position where you have stopped playback as a resume point. (The inside of the disc status indicator on the front display panel blinks while memorizing.)

● The unit retains a memory of the resume points of the last 30

discs played back, even though they have been ejected if ARESUMEB is set to ADISC RESUMEB. (A pg. 71)

● Performing the following steps would erase the resume points:

(The inside of the disc status indicator stops blinking and lights.)

When ARESUMEB is set to AONB:

• Press A to turn off the unit.

• Press

M to take out the disc.

• Press

o in stop mode.

• Press TOP M ENU to display the top menu, then start playback by selecting an item, etc.

• Press MENU to display the disc menu, then start playback by selecting an item, etc.

When ARESUMEB is set to ADISC RESUMEB:

•Set ARESUMEB to AOFFB. (A pg. 71)

• Press

o in stop mode.

• Press TOP M ENU to display the top menu, then start playback by selecting an item, etc.

• Press MENU to display the disc menu, then start playback by selecting an item, etc.

2 Press I in stop mode to resume playback. The unit starts

playback from the resume point.

NOTES:

● ADISC RESUMEB setting works on DVD VIDEO, VCD, SVCD and

already finalized DVD-R/DVD-RW (video mode) discs. For other types of discs, the function under AONB setting will be applied even if ARESUMEB is set to ADISC RESUMEB. (A pg. 71)

● If you stop the playback of a disc for which a resume point has

already been memorized, the memory will be updated with the new resume point.

● After the unit has memorized the resume points for 30 discs,

remembering a new resume point will cause the unit to delete the oldest memorized point. Stopping playback of a disc for which a resume point is already stored may change the order in which the points are stored. This may potentially change the order in which points are deleted.

● When the unit memorizes a resume point for a disc, it also

remembers audio language, subtitle and angle settings.

● This function may not work for some Video CD/SVCDs.

● When ARESUMEB is changed to AONB or AOFFB (A pg. 71),

resume points of the discs memorized with ARESUMEB set to ADISC RESUMEB will be cleared.

● Resume points are memorized for each side of a double-sided

disc.

● When you switch to HDD while playing back JPEG/MP3 files,

playback stops. The Resume Function doesn’t work when you switch to DVD thereafter to playback the disc.

BASIC OPERATIONS ON DVD DECK

EN 27

CABLE/DBS

DVDTV

DVD

0-9

MARK

ENTER

S/PREVIOUS

I o

REC MODE/REMAIN

DISPLAY

AUDIO

Selection Keys

FGDE

RETURNMENU T/NEXT

SET UP ON SCREEN

ANGLESUBTITLE

Marking Positions To Play Back Again Later

It is possible to mark positions (up to 999 points) where you want to play back once again later, and start playback from a marked position. Marking onto DVD-RAM/RW (VR mode only) discs when recording is helpful to locate a start point when you play back the discs later.

To mark positions:

During playback, press MARK at positions you want to mark.

● AMARKB appears on the TV screen.

You can easily locate the marked positions using S or T when you play back the disc.

To delete the marked positions:

While paused, press S or T to locate a marked position you want to delete, then press MARK.

● Crossed AMARKB appears on the

TV screen, and the marked position is deleted.

NOTES:

● When a monaural program changes to a stereo program while

recording, a mark signal is automatically recorded.

● For DVD-R/RW (Video mode) discs, marks are assigned

automatically every 5 minutes.

● If MARK is pressed when playing back a disc that does not allow

marks to be inserted, A7B appears on the TV screen.

Checking The Time Information

You can check time information of a disc on the front display panel and the TV screen.

8 DVD-RAM/DVD-R/DVD-RW

Each press of DISPLAY changes the display as follows: During recording

Clock time (front display panel only) N Current title elapsed time N Disc remaining time N (back to the beginning)

During playback

Each title elapsed time N Current title elapsed time N Disc remaining time* N (back to the beginning)

* only discs before finalizing

During recording/playback or in stop mode Press REC MODE.

● The disc remaining time according to recording modes appears

on the TV screen.

● It is possible to check disc remaining time according to recording

modes also by pressing REMAIN.

● In FR mode, it is possible to set recording time in detail. While the

recording mode and the disc remaining time are displayed by pressing REMAIN, press selection keys to select AFRB, then press DE to select the desired recording time. (A pg. 36)

● It is not possible to switch the recording mode during playback or

while recording.

8 Video CD/SVCD/Audio CD During playback or in stop mode

Current track elapsed time N Current track remaining time N Tot al elapsed time N Total remaining time N (back to the beginning)

NOTES:

● When a PBC-compatible Video CD/SVCD disc is loaded,

deactivate the PBC function. (A pg. 28)

● For pre-recorded DVD VIDEO, only the title, chapter and elapsed

time are displayed when ON SCREEN is pressed.

Angle Selection

You can enjoy a variety of scene angles if a DVD VIDEO disc contains Amulti-angleB parts, where the same scene was shot from different angles. If the disc contains Amulti-angleB parts, AyB appears on the TV screen at the beginning of the Amulti-angleB part.

1 Press ANGLE during playback.

The angle selection display appears on the TV screen.

2 Press ANGLE or selection

keys to select your desired

angle.

● Each time you press ANGLE or the selection keys, the angle

changes.

● When A7B appears on the TV screen, the current scene is not

recorded from multiple angles. In addition, some discs prohibit angle selection.

● To clear the angle selection display, press ENTER. In addition,

the angle selection display disappears automatically if no operation is done for 10 seconds.

When 3 scene angles are contained.

28 EN

BASIC OPERATIONS ON DVD DECK

Subtitle Selection

Some DVDVIDEO discs contain more than one subtitle language, from among which you can choose the desired subtitle language. AhB appears on the TV screen at the beginning of the part where more than one subtitle language are recorded.

1 Press SUBTITLE during

playback. The subtitle selection display appears on the TV screen.

● Each time you press

SUBTITLE, the subtitle display is switched on and off.

When 3 subtitle languages are contained.

ENGLISH

2 Press selection keys to select your desired language.

● To clear the subtitle selection display, press ENTER.

NOTES:

● When A7B appears on the TV screen, no subtitle language is

recorded.

● When the subtitle language won’t be changed with the procedure

above, change the subtitle on a disc menu displayed by pressing MENU.

Audio Channel Selection

When watching bilingual programs or playing discs on which you recorded bilingual or stereo programs, you can choose the desired audio channel.

● When ASUPERIMPOSEB is set to AAUTOB, you can confirm on

the TV screen the audio channel you have chosen. (A pg. 72)

● Each time you press AUDIO, the audio

channel changes.

TRACK

On-Screen Display

For stereo discs For audio of left channel For audio of right channel

When you can’t switch the audio channel of a bilingual program

When the unit is connected with a digital audio device using an optional optical cable and ADIGITAL AUDIO OUTB is set to ADOLBY DIGITAL/PCMB, it is not possible to switch the audio channel of a bilingual program recorded on a DVD-RAM or DVD-RW (VR mode) disc. (A pg. 69) In this case, perform the following steps using the remote control to switch ADIGITAL AUDIO OUTB from ADOLBY DIGITAL/PCMB to APCM ONLYB.

A Press SET UP to access the Main Menu screen. B Press selection keys to select ADVD VIDEO SET UPB, then

press G.

C Press selection keys to select AAUDIO OUTPUTB, then press

D Press selection keys to select ADIGITAL AUDIO OUTB, then

press ENTER.

E Press selection keys to select APCM ONLYB, then press

ENTER. (A pg. 70)

F Press SET UP to complete the setting. G Press AUDIO to select the desired audio channel.

USE

Audio Language/Sound Selection

Some DVDVIDEO discs contain the multiple audio language or sound. You can select the desired audio language or sound. For some Video CD/SVCD discs, you can switch the audio channel to choose Karaoke either with or without the vocal.

1 Press AUDIO during playback.

The Audio Language/Sound selection display appears.

2 Press AUD IO or selection

keys to select your desired

audio language/sound.

● Each time you press AUDIO or the selection keys, the audio

language/sound changes.

● To clear the Audio Language/Sound selection display, press

ENTER.

NOTES:

● When A7B appears on the TV screen, no other audio language is

recorded.

● When the audio language won’t be changed with the procedure

above, change the audio on a disc menu displayed by pressing MENU.

● Pressing AUDIO to select the audio language/sound is only

possible during playback. It is not possible to select by pressing AUDIO in stop mode. However, you can select the desired audio language/sound from the setup menu while in stop mode.

For example: DVD VIDEO

When 3 audio languages are contained.

Playback Control (PBC) Function

Some Video CD/SVCD discs support the PBC function. PBC is an abbreviation of APlay Back ControlB. A Video CD/SVCD disc recorded with PBC has its own menus, such as a list of the songs on the disc. You can locate a specific scene by using the menu.

1 Press I in stop mode. The PBC menu appears. 2 Press the number keys to enter the number of the desired

scene, then press ENTER. The unit starts playback of the selected item.

● APBCB appears on the front display panel.

● When ANEXTB or APREVIOUSB appears on the TV screen:

Pressing NEXT(T) advances to the next page. Pressing PREVIOUS(S) returns to the previous page.

● You can return to the menu by pressing RETURN.

● The method of the operation is different depending on the disc.

NOTE:

If you want to playback a PBC-compatible Video CD/SVCD disc without activating the PBC function, start playback with the PBC function, then press o to stop playback. The TV screen becomes all blue. Then start playback in stop mode by using the number keys to choose the track, then press ENTER.

Using The On-screen Bar

DVD-

VIDEO

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

CHAPTER 99 EACH 0:00TITLE 99

The on-screen bar allows you to control various playback functions. Some of the functions operated on Navigation Menu can be controlled on the On-screen bar.

ATTENTION:

The on-screen bar can also be used for the HDD deck.

Be sure to clear Library Database Navigation screen by pressing NAVIGATION.

CABLE/DBS

DVDTV

ENTER

NAVIGATION

Selection Keys

FGDE

RETURN

BASIC OPERATIONS ON DVD DECK

EN 29

A Disc type. B Select this for Repeat Playback. (See below) C Select this for A-B Repeat Playback. (A pg. 30) D Select this for search function. (A pg. 30) E Select this for time search function. (A pg. 31) F Select this to switch Simulated Surround Effect function.

(A pg. 31)

G Select this for Picture Control function. (A pg. 31) H Select this to switch picture source type. (A pg. 32) I Current status area for the selected item. J Select this for Program Playback. (A pg. 32) K Select this for Random Playback. (A pg. 32) L Select this to control the switching interval of the slide show.

(A pg. 32)

NOTE:

Although examples of the on-screen bar are provided here only for 3 types of discs, the on-screen bar will be displayed for whichever disc indicated in the left column.

Basic Operation On The On-screen Bar

Example: When selecting Picture Control function of DVD

During playback or while stopped

1 Press ON SCREEN twice to access the on-screen bar. The

item currently selected is highlighted and pointed by :.

3D-ON CINEMA AUTO

ON SCREEN

How To Access The On-screen Bar

1 Press ON SCREEN twice whenever a disc is loaded.

Contents of the on-screen bar during playback

DVD VIDEO

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

Video CD/SVCD

TRACK 99

VCD

JPEG disc

JPEG

TRACK 99GROUP 99

5sec

3D-ON CINEMA AUTO

EACH 0:00

CINEMA

2 Press selection keys to select AB, then press ENTER. The

pop-up window appears under the selected item.

3D-ON CINEMA AUTO

3 Press selection keys to select the desired option, then press

ENTER.

3D-ON CINEMA AUTO

NORMAL CINEMA SHARP SOFT

To clear the on-screen bar Press ON SCREEN.

NOTE:

See the corresponding pages for details on each menu item.

Repeat Playback

You can repeat playback as you like according to the type of disc.

1 Press ON SCREEN twice to access the on-screen bar. 2 Press selection keys to select AxB, then press ENTER. The

pop-up window appears under the selected item.

3D-ON CINEMA AUTO

3 Press selection keys repeatedly to select the desired Repeat

mode, then press ENTER.

30 EN

DVD-

VIDEO

CHAPTER 99 EACH 179:59GROUP 99

DVD-RAM/RW/R

BASIC OPERATIONS ON DVD DECK

OFF:

Repeat playback is not performed.

ALL REPEAT:

The whole disc is played back repeatedly.

TITLE REPEAT:

The current title is played back repeatedly.

DVD VIDEO

OFF:

Repeat playback is not performed.

TITLE REPEAT:

The current title is played back repeatedly.

CHAPTER REPEAT:

The current chapter is played back repeatedly.

Audio CD/Video CD/SVCD/JPEG/MP3

OFF:

Repeat playback is not performed.

ALL REPEAT:

The whole disc is played back repeatedly.

TRACK REPEAT*:

The current track is played back repeatedly.

*ATRACK REPEATB cannot be selected for JPEG discs.

To clear the on-screen bar Press ON SCREEN.

To cancel Repeat Playback

Repeat the above procedure from step 1, select AOFFB in step 3, then press ENTER.

NOTES:

● Repeat Playback is not possible for a Video CD/SVCD with PBC

function.

● Repeat Playback may not work properly depending on the type of

the disc being used.

A-B Repeat Playback

You can repeat the desired part.

During playback

1 Press ON SCREEN twice to access the on-screen bar. 2 Press selection keys to select AA-B xB. 3 Press ENTER at the beginning of the desired part you want to

repeat (point A). The elapsed playing time of the point A appears.

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

AB1:25:58 : :

4 Press ENTER at the end of the desired part you want to repeat

(point B). The elapsed playing time of the point B appears.

● The selected part of the disc (between point A and B) is played

repeatedly.

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

AB1:25:58 1:40:00

To clear the on-screen bar Press ON SCREEN.

3D-ON CINEMA AUTO

To cancel A-B Repeat Playback Press selection keys to select AA-B xB, then press ENTER.

NOTES:

● A-B Repeat Playback may not work properly depending on the

type of disc being used.

● The subtitles recorded around the A-B point may not appear.

● When the end of the item is reached before the end point is set,

the on-screen bar disappears from the TV screen. In such a case, repeat the procedure from step 1.

● The point B must be set at least 3 seconds after the point A.

● When playing back a DVD, A-B Repeat Playback is possible only

within the same title.

● AA-B xB cannot be selected during Program and Random

Playback.

● AA-B xB cannot be selected while stopped.

Locating The Beginning Of A Desired Selection

You can locate the beginning of a title, chapter, group or track.

During playback or while stopped

1 Press ON SCREEN twice to access the on-screen bar. 2 Press selection keys to select A9B, then press ENTER. 3 Press selection keys to select the desired item, then press

ENTER.

● Skip this step for Video CD/SVCD and Audio CD.

For DVD-RAM/RW/R, DVD VIDEO

ATITLE SEARCHB or ACHAPTER SEARCHB is selectable. (However, only ATITLE SEARCHB is selectable while stopped.)

For JPEG, MP3

AGROUP SEARCHB or ATRACK SEARCHB is selectable. (However, only AGROUP SEARCHB is selectable while stopped.)

For Video CD/SVCD, Audio CD

ATRACKB is selectable.

NOTE:

Settings that are selectable during playback and stop mode differ depending on the type of disc and search used.

CINEMA

TITLE SEARCH CHAPTER SEARCH

4 Press the number keys to enter the desired item number, then

press ENTER.

● Playback starts from the selected section.

Examples:

A To select track 5, press the number key A5B. B To select track 15, press the number key A1B and A5B. C To select track 25, press the number key A2B, then A5B.

If you have specified a wrong selection

Press RETURN on the remote control and repeat the above procedures from step 2.

To clear the on-screen bar Press ON SCREEN.

NOTES:

● When A7B is displayed on the TV screen in step 4, the chapter

you have selected is not contained in the disc, or chapter search does not work on the disc.

● Before you press ENTER, playback may start automatically when

you enter the section’s number depending on the disc.

● This function is not possible for a Video CD/SVCD with PBC

function.

BASIC OPERATIONS ON DVD DECK

DVD-

VIDEO

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

CHAPTER 99 EACH 0:00TITLE 99

EN 31

CABLE/DBS

DVDTV

0-9

CANCEL

ENTER

CLEAR

Selection Keys

FGDE

RETURN

ON SCREEN

Time Search

You can play back a disc from the desired point by specifying the elapsed playing time from the beginning of a program (DVD-RAM, DVD-R, DVD-RW, DVD VIDEO and HDD) or a disc (Video CD/ SVCD and Audio CD).

1 Press ON SCREEN twice to access the on-screen bar. 2 Press selection keys to select Aj9B, then press ENTER. The

pop-up window appears under the selected item.

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

CINEMA AUTO

Simulated Surround Effect

It is possible to get a simulated surround effect from your stereo system. You can enjoy the virtual surround sound with your 2channel stereo system.

1 Press ON SCREEN twice to access the on-screen bar. 2 Press selection keys to select AB, then press ENTER.

● A3D-ONB appears above the selected item and Simulated

Surround Effect is activated.

● Each time you press ENTER, A3D-ONB appears and disappears

alternately.

3D-ON CINEMA AUTO

To clear the on-screen bar Press ON SCREEN.

To cancel the simulated surround effect Press ENTER to clear A3D-ONB from the screen.

NOTES:

● Simulated Surround Effect works correctly only when playing

back a title recorded in multichannels.

● Simulated Surround Effect does not affect the DVD VIDEO

bitstream signal from the [DIGITAL AUDIO OUT] connectors.

● When Simulated Surround Effect is activated, the settings of

AANALOG AUDIO OUTB and AD. RANGE CONTROLB are disabled. (A pg. 70)

● Simulated Surround Effect cannot be activated under the

following conditions:

● When the HDD deck is in the recording mode.

● When the HDD or DVD deck is in the timer standby mode.

● When a disc containing both the Dolby Digital 5.1CH and 2CH

sound formats is playing back a scene that is not in the 5.1CH sound format.

Adjusting The Picture Quality

3 Press the number keys to enter the time, then press ENTER.

Playback starts from the specified time. Example: To play back from a point 12 (minutes): 50 (seconds) elapsed.

TIME

Press 1

If you have specified a wrong selection,

Press RETURN on the remote control and repeat the above procedures from step 2.

To clear the on-screen bar Press ON SCREEN.

NOTES:

● When A7B is displayed on the TV screen in step 3, you have

selected a point that exceeds the recording time of the disc.

● Some DVDVIDEO discs do not contain time information, and it is

not possible to use the Time Search function. In such cases, A7B is displayed on the TV screen as well.

● This function is not possible for a Video CD/SVCD with PBC

function.

TIME

Press 2

TIME

Press 0Press 5

You can obtain optimal picture quality by selecting an appropriate picture mode.

1 Press ON SCREEN twice to access the on-screen bar. 2 Press selection keys to select AB, then press ENTER. The

pop-up window appears under the selected item.

CINEMA AUTO

3 Press selection keys to select the desired option, then press

ENTER.

NORMAL:

Normally select this option.

CINEMA:

Suitable for a movie disc, etc.

SHARP:

Clearer, sharper-edged picture when viewing images with lots of flat, same-colored surfaces such as cartoons.

SOFT:

Select this option when too much noise appears.

To clear the on-screen bar Press ON SCREEN.

32 EN

VCD

TRACK 99 EACH 0:00

JPEG

TRACK 99GROUP 99

BASIC OPERATIONS ON DVD DECK

Setting The Progressive Mode

You can obtain optimal picture quality by selecting whether the content on the disc is processed by field (video source) or by frame (film source).

1 Set the unit to the progressive scan mode. (A pg. 76) 2 Press ON SCREEN twice to access the on-screen bar. 3 Press selection keys to select AB, then press ENTER. The

pop-up window appears under the selected item.

CHAPTER 99 EACH 0:00TITLE 99

AUTO

CINEMA

DVD-

VIDEO

3D-ON

4 Press selection keys to select the desired option, then press

ENTER.

AUTO:

This mode automatically detects film and video content for

progressive playback. When film content is found, flag detection

is used to invoke playback of film data in full screen. When

video content is found, pictures from multiple fields are used to

detect sections with movement, and then this movement

undergoes advanced image processing for output of sharp,

detailed progressive images without any reduction in image

quality where movement occurs. Normally, operation in this

mode is recommended.

FILM:

Suitable for playing back a progressive scanned film source

disc.

VIDEO:

Suitable for playing back a video source disc. The outlines on

the played back pictures will be soft.

To clear the on-screen bar Press ON SCREEN.

Program Playback

4 Press I. Playback starts in the programmed order.

● When all of the programmed tracks have been played back,

Program Playback stops, but the programmed information remains.

● To add tracks to the end of the program, perform step 3.

● During Program Playback, pressing T skips to the next

selection of the program. Pressing S returns to the beginning of the currrent selection.

To clear the on-screen bar and the contents of the program Press ON SCREEN.

To cancel Program Playback Press selection keys to select APRGMB, then press ENTER.

NOTE:

Program Playback is not possible depending on the type of disc.

Random Playback

You can play back all the tracks on the disc in random order.

While stopped

1 Press ON SCREEN twice to access the on-screen bar. 2 Press selection keys to select ARNDB, then press ENTER.

Playback starts in random order.

CINEMA

To clear the on-screen bar Press ON SCREEN.

To cancel Random Playback Perform steps 1 and 2.

NOTE:

The same track will not be played back more than once during Random Playback.

Select The Switching Interval Of The Slide Show

You can program up to 30 tracks (Video CD/SVCD or Audio CD) to play back in the desired order.

While stopped

1 Press ON SCREEN twice to access the on-screen bar. 2 Press selection keys to select APRGMB, then press ENTER.

The program table appears under on-screen bar.

TRACK 99 EACH 0:00

VCD

3 Press the number keys to

enter the track numbers in the

desired order. Examples: A To select track 5, press the

number key A5B and ENTER. B To select track 15, press the

number key A1B and A5B.

C To select track 25, press the number key A2B and A5B.

If you have specified a wrong selection

Press CANCEL(L). The last selection is erased. Or press CLEAR

(o). The whole selection is erased.

USE [0-9] KEYS TO SELECT TRACK

Program Total Time

CINEMA

You can control the switching interval of the slide show.

1 Press ON SCREEN twice to access the on-screen bar. 2 Press selection keys to select AB, then press ENTER. The

pop-up window appears under the selected item.

5sec

3 Press selection keys to select the desired option, then press

ENTER.

● Each time you press the selection keys, the interval changes

as follows: 5sec Y 10 sec Y 15 sec Y 20 sec Y 25 sec Y 30 sec Y (Back to the beginning)

To clear the on-screen bar Press ON SCREEN.

NOTE:

JPEG files are played back as a slide show. It may take more time to display an image with larger file size.

Parental Lock

This function restricts playback of DVDVIDEO discs which contain violent (and other) scenes according to the level set by the user. For example, if a movie which includes violent scenes supports the parental lock feature, such scenes which you do not want to let children view can be cut or replaced by other scenes.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press DVD so that the DVD lamp lights up on the unit.

CABLE/DBS

DVDTV

DVD

0-9

ENTER

Selection Keys

FGDE

SET UP

BASIC OPERATIONS ON DVD DECK

EN 33

8 Press selection keys to select your country code, then press

ENTER.

● If you do not need to change your country code, jump to 10.

● See ACountry/Area Code List for Parental LockB (A pg. 82).

9 Press the number keys to enter the same password as in

step 6 above, then press ENTER.

10 Press SET UP to complete the setting.

NOTE:

Remember your password, or make a note of it.

To Change The Settings

You can change the Parental Lock settings later.

1 Perform steps 1 to 3 of ATo Set Parental Lock For The First

TimeB to access the APARENTAL LOCKB screen before continuing.

To change the level

2 Press selection keys to select APARENTAL LEVELB, then

press ENTER.

3 Press selection keys to select the desired level, then press

ENTER.

To change the country code

4 Press selection keys to select ACOUNTRY CODEB, then press

ENTER.

5 Press selection keys to select your country code, then press

ENTER.

● See ACountry/Area Code List for Parental LockB (A pg. 82).

6 Press the number keys to enter the same password as in

step 6 of ATo Set Parental Lock For The First TimeB, then press ENTER.

7 Press SET UP to complete the setting.

NOTE:

If you forget your password, enter A8888B in step 6.

To Set Parental Lock For The First Time

While stopped

1 Press SET UP to access the Main Menu screen. 2 Press selection keys to select ADVD VIDEO SET UPB, then

press G.

3 Press selection keys to select

APARENTAL LOCKB, then

press G.

4 Press selection keys to select

APARENTAL LEVELB, then

press ENTER.

5 Press selection keys to select

DVD VIDEO SET UP

HDD/DVD/DV SET UP

LANGUAGE SET

AUDIO OUTPUT

PARENTAL LEVEL

COUNTRY CODE

ENTER

SET UP

EXIT

SELECT

DVD VIDEO SET UP

HDD/DVD/DV SET UP

LANGUAGE SET AUDIO OUTPUT

PARENTAL LEVEL

COUNTRY CODE

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

the desired level, then press

ENTER.

● The smaller the value of level

is, the more restrictive the

SET UP

EXIT

SELECT

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

ENTER

Parental Lock level becomes.

● Select ANONEB to cancel the restriction.

6 Press the number keys to enter your desired four-digit number,

then press ENTER.

● If you made a mistake, enter a correct number again.

7 Press selection keys to select ACOUNTRY CODEB, then press

ENTER.

INITIAL SET UP

FUNCTION SET UP

PARENTAL LOCK DISC PLAY SET UP

NONE

INITIAL SET UP

FUNCTION SET UP

PARENTAL LOCK DISC PLAY SET UP

NONE

To Temporarily Release Parental Lock

When you set the Parental Lock level strictly, some discs may not be played back at all. When you insert such a disc and try to play it back, the confirmation screen appears on the TV screen, asking you whether you want Parental Lock to be temporarily released or not.

1 Load a disc.

● If the disc is rated higher than the selected level, the

confirmation screen appears.

2 Press selection keys to select AYESB, then press ENTER.

● If you select ANOB, you cannot play back that disc.

3 Press the number keys to enter the same password as in

step 6 of ATo Set Parental Lock For The First TimeB, then press ENTER.

● When you enter the correct password, the Parental Lock is

released and the unit starts playback.

● If you enter a wrong password, AENTRY ERRORB appears on

the TV screen. Enter the correct password.

● If you have successively entered wrong password three times,

AENTRY ERROR CAN NOT CHANGE PASSWORDB appears on the TV screen. In such a case, press ENTER. The disc will stop. Then play back the disc again, and try the procedure again from step 1.

NOTE:

If you forget your password, enter A8888B in step 3.

34 EN

BASIC OPERATIONS ON DVD DECK

Basic Recording

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

ATTENTION:

It is not possible to record programs on a DVD-R disc which has already been finalized.

DV/HDD/DVD

SELECT

MODE

CABLE/DBS

DVD

REC

DVDTV

CH +/

DVD lamp

DVD recording lamp

7 Press o twice to stop recording.

● It takes about 10 seconds to end the writing session when you

stop recording.

NOTES:

● When switching from the HDD to the DVD deck, or when the unit

is turned on while a playback only disc is loaded, the DVD deck enters into resume stop mode automatically and the TV screen becomes all blue. To display the EE* signal on the screen, press o.

* EE means Electronics to Electronics, no mechanical movement is

involved. EE signal means a program received with the unit's tuner or the AV input signals.

●

It is recommended to format a DVD-RAM disc before use if you use the disc on this unit for the first time.

● When using a brand-new DVD-RW disc, format the disc either in

VR mode or in Video mode. (A pg. 74)

● Recordings made on DVD-R/RW disc must be finalized to play

back on other DVD players. Perform AFinalize A Disc (DVD Deck Only)B (A pg. 75).

● You can record up to 99 programs and 99 play lists on each disc.

● Some programs can only be recorded one time.

● When recording is started, an index of the first part of recording is

automatically recorded (A pg. 50). To delete the index, refer to page 52.

● Recording sometimes may stop or cannot be performed even

when there is enough available capacity remaining on the disc if the signal source is copy-protected or intermittent.

● It is not possible to record on both DVD and HDD simultaneously.

● It is not possible to record from this unit’s built-in tuner to the DV

deck.

0-9

CH +/–

ENTER

R o

REC MODE

1 Load a recordable disc.

● For details, refer to APlacing A DiscB (A pg. 10).

2 Press DV/HDD/DVD SELECT on the unit repeatedly or DVD on

the remote control so that the DVD lamp lights up on the unit.

3 Press CH +/– or the number keys to select the channel you

wish to record.

4 Press REC MODE repeatedly to select the recording mode,

then press ENTER.

● Each time you press REC MODE, the recording mode changes

as follows:

XP N SP N LP NEP N FR (60-360*, 420, 480) N (Back to the

beginning)

* The value is selectable from 1 to 6 hours in 5-minute intervals by

● For details on the recording mode, see the right column.

DE repeatedly after selecting

pressing value in 30-minute intervals, press and hold

FR60–FR360B. To change the

DE.

5 Press R on the unit to start recording. Or while holding R, press

I on the remote control.

● The DVD recording lamp lights up on the unit.

6 Press R and W on the remote control simultaneously to pause

recording.

● To resume recording, press R and I simultaneously.

Recording Mode

MPEG2 format is used as recording format. As a guide for picture quality, the AbpsB unit is used to represent how much data can be recorded per second. The larger this value is, the better the picture quality becomes but more capacity is required for the recording. Select XP or SP for programs where quick movement occurs, such as sports programs, and LP or EP for talk shows, etc. with relatively less movement. The recording modes for a 4.7 GB disc are set as follows:

Recording mode

Recording amount

(approx.)

Maximum recording

time (approx.)

XP 10 Mbps 1 hour SP 5 Mbps 2 hours LP 2.5 Mbps 4 hours EP 1.6 Mbps 6 hours

60-360

(A pg. 36)

420 7 hours

The amount varies

depending on the

selected time.

1 – 6 hours

480 8 hours

● For details on FR mode, refer to AFree Rate FunctionB (A pg. 36).

BASIC OPERATIONS ON DVD DECK

EN 35

Recording Features

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press DV/HDD/DVD SELECT on the unit repeatedly or DVD

on the remote so that the DVD lamp lights up on the unit.

DV/HDD/DVD

SELECT

CABLE/DBS

DVDTV

REMAIN

DVD lamp

DVD

DISPLAY

Instant Timer Recording (ITR)

This easy method lets you record for 30 minutes to 6 hours (selectable in 30-minute intervals), and shuts the unit off after recording is finished.

1 Press R on the unit to start recording. 2 Press R again to engage the ITR mode.

● On the front display panel, A0:30B appears.

3 If you want to record for more than 30 minutes, press R to

extend the time. Each press extends recording time by 30 minutes.

NOTES:

● You can only perform ITR using the R button on the unit.

● ITR is not possible during timer recording.

● When the recording capacity becomes full during timer recording

or Instant Timer Recording, the unit automatically performs ARelief RecordingB (A pg. 48).

Watch Another Program While Recording On The Unit

While recording is going on, you can watch another program on the TV. It does not interfere with recording.

1 Turn on the TV. 2 Select the desired channel to watch on the TV using your TV’s

remote control.

Elapsed Recording Time And Disc Remaining Time Indication

During recording, press DISPLAY repeatedly until the desired indication appears on the front display panel.

● Each time you press DISPLAY, the time indication changes as

follows: Elapsed recording time N Disc remaining time N Clock N (Back to the beginning)

● You can also check the disc remaining time by pressing REMAIN

while the unit is stopped or recording is in progress. The list of disc remaining times for all recording modes appears on the TV screen.

36 EN

BASIC OPERATIONS ON DVD DECK

Free Rate Function

To record the entire program, the unit automatically sets the appropriate recording mode depending on the combination of the total time of the program to be recorded and either the remaining disc space or the specified recording time (from 60 minutes to 480 minutes).

8 To record the entire program within the actual remaining

disc space (DVD deck only)

Select AFR (JUST)B in a recording mode selection procedure.

● Note that this function is available only for timer programming

recording (A pg. 46, 48) and dubbing from HDD to DVD (A pg. 57).

8 To record the entire program by specifying the desired

recording time

Select AFR60–FR360B, AFR420B or AFR480B in a recording mode selection procedure. (A pg. 34, 37, 46, 48)

8 To record a 25-min. long daily program five times just on

the same DVD disc for example

Perform AVCR Plus+ Timer ProgrammingB (A pg. 46) procedure. Be sure to set the recording mode to AFR125B and set Weekly/ Daily Rec Function to AMON-FRIB in step 8 to fit the total recording time to the whole disc space.

A: 1st

Blank

B: 2nd C: 3rd D: 4th E: 5th

Second Audio Recording

This unit’s built-in MTS decoder enables reception of Multichannel TV Sound broadcast. To record a SAP program received, set A2ND AUDIO RECORDB to AONB. (A pg. 71)

NOTES:

When the channel is changed on the unit;

● The AMONOB indicator appears on the screen for about 5

seconds if the program is a monaural broadcast.

● The ASTEREOB indicator appears on the screen for about 5

seconds if the program is a stereo broadcast.

● Both ASTEREOB and ASAPB indicators appear when a stereo

program is accompanied by SAP sound.

● Both AMONOB and ASAPB indicators appear when the main audio

on the monaural broadcast is accompanied by SAP sound.

When the same program is recorded in SP mode instead of in AFR125B, the 5th program cannot be recorded.

A: 1st

Blank

B: 2nd C: 3rd D: 4th E: Blank (20 min.)

NOTES:

● You can program this unit to timer record, regardless of the disc

remaining time. When the disc remaining time is not enough, the unit performs ARelief RecordingB (A pg. 48). To avoid this, make sure of the disc remaining time before setting timer programming. (Example) If you programmed to timer record for 60 minutes in SP mode on a 120-minute disc, the disc remaining time would be 30 minutes in XP mode, 60 minutes in SP mode, 120 minutes in LP mode, 180 minutes in EP mode, and 240 minutes in FR480 mode. Timer recording will not complete beyond these remaining times.

● The maximum recording time of FR (JUST) mode is the same as

the recording time of FR480 mode. When timer programming a long program in FR (JUST) mode on a disc whose remaining time is short, it is recommended to check the disc remaining time in FR480 mode to see if the remaining time is enough for the program.

● Even if more than one program are timer programmed in FR

(JUST) mode, only the first one is recorded.

● In order to ensure that the recording fits on the disc, this feature

may leave a slight non-recorded section at the end of the disc.

● There may be some noise and sound disturbance at the point on

the disc where the unit switches the mode.

Basic Recording

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

ATTENTION:

The HDD on the unit requires approximately 20 seconds to start up after the unit has been turned on, during which no operation can be made.

DV/HDD/DVD

SELECT

CABLE/DBS

CH +/–

ENTER

DVDTV

REC MODE

HDD

0-9

REC MODE

I o R

CH +/

HDD lamp

BASIC OPERATIONS ON HDD DECK

EN 37

NOTES:

● Continuous recording for over 48 hours is not possible.

● It is not possible to record on both DVD and HDD simultaneously.

● It is not possible to record from this unit’s built-in tuner to the DV

deck.

Pause recording on HDD deck

It is not possible to pause recording. Pressing W initiates Live Memory Playback. However, it is still possible to pause recording only when recording the channels of external sources (AL-1B, AF-1B and ADVB). While holding R, press W on the remote control. To resume recording, while holding R, press I on the remote control. No operation can be made with the buttons on the unit.

Recording Mode

Recording mode Maximum recording time (approx.)

XP 53 hours

SP 109 hours

LP 218 hours

EP 328 hours

FR480 473 hours

● For details on FR mode, refer to AFree Rate FunctionB (A pg. 36).

NOTE:

The maximum recording time stated in the above table are the approximate time under unused condition.

1 Press DV/HDD/DVD SELECT on the unit repeatedly or HDD on

the remote control so that the HDD lamp lights up on the unit.

2 Press CH +/– or the number keys to select the channel you

wish to record.

3 Press REC MODE repeatedly to select the recording mode,

then press ENTER.

● Each time you press REC MODE, the recording mode changes

as follows: XP N SP N LP NEP N FR (60-360*, 420, 480) N (Back to the beginning)

* The value is selectable from 1 to 6 hours in 5-minute intervals by

● For details on the recording mode, see the right column.

DE repeatedly after selecting

pressing value in 30-minute intervals, press and hold

FR60–FR360B. To change the

DE.

4 Press R on the unit to start recording. Or while holding R, press

I on the remote control.

● The HDD recording lamp lights up on the unit.

5 Press o twice to stop recording.

● Pressing o once displays the confirmation message to stop

recording. Press o again to terminate recording.

38 EN

BASIC OPERATIONS ON HDD DECK

Recording Features

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press DV/HDD/DVD SELECT on the unit repeatedly or HDD

on the remote so that the HDD lamp lights up on the unit.

HDD lamp

HDD

REMAIN

DV/HDD/DVD

SELECT

CABLE/DBS

DISPLAY

DVDTV

Watch Another Program While Recording On The Unit

While recording is going on, you can watch another program on the TV. It does not interfere with recording.

1 Turn on the TV. 2 Select the desired channel to watch on the TV using your TV’s

remote control.

Elapsed Recording Time And Disc Remaining Time Indication

During recording, press DISPLAY repeatedly until the desired indication appears on the front display panel.

● Each time you press DISPLAY, the time indication changes as

follows: Elapsed recording time N Disc remaining time N Clock N (Back to the beginning)

● You can also check the disc remaining time by pressing REMAIN

while the unit is stopped or recording is in progress. The list of disc remaining times for all recording modes appears on the TV screen.

Second Audio Recording

This unit’s built-in MTS decoder enables reception of Multichannel TV Sound broadcast. To record a SAP program received, set A2ND AUDIO RECORDB to AONB. (A pg. 71)

NOTES:

When the channel is changed on the unit;

● The AMONOB indicator appears on the screen for about 5

seconds if the program is a monaural broadcast.

● The ASTEREOB indicator appears on the screen for about 5

seconds if the program is a stereo broadcast.

● Both ASTEREOB and ASAPB indicators appear when a stereo

program is accompanied by SAP sound.

● Both AMONOB and ASAPB indicators appear when the main audio

on the monaural broadcast is accompanied by SAP sound.

Instant Timer Recording (ITR)

This easy method lets you record for 30 minutes to 6 hours (selectable in 30-minute intervals), and shuts the unit off after recording is finished.

1 Press R on the unit to start recording. 2 Press R again to engage the ITR mode.

● On the front display panel, A0:30B appears.

3 If you want to record for more than 30 minutes, press R to

extend the time. Each press extends recording time by 30 minutes.

NOTES:

● You can only perform ITR using the R button on the unit.

● ITR is not possible during timer recording.

● When the recording capacity becomes full during timer recording

or Instant Timer Recording, the unit is automatically shut off.

BASIC OPERATIONS ON HDD DECK

EN 39

Basic Playback

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

DV/HDD/DVD

SELECT

CABLE/DBS

HDD

ENTER

DISPLAY

Playback Features

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press HDD so that the HDD lamp lights up on the unit.

HDD

DVDTV

O/SLOW

JUMP

JUMP +

Variable Speed Search

During playback, press N for forward variable speed search, or O for reverse variable speed search.

● Each press of the button increases the search speed for each

direction.

● To resume normal playback, press I.

Reverse

CABLE/DBS

MARK

N/SLOW +

ON SCREEN

DVDTV

Forward

ATTENTION:

● It may take a few seconds to start playback. This is not a

malfunction.

● Forward/reverse high-speed search and other operations

cannot be performed while playback is stopped.

1 Press DV/HDD/DVD SELECT on the unit repeatedly or HDD on

the remote so that the HDD lamp lights up on the unit.

2 Press I to start playback.

● The Library Database Navigation also enables you to search

and select the desired programs. (A pg. 51)

3 Press W to pause playback.

● To resume normal playback, press I.

4 Press o to stop playback.

NOTES:

● When the Library Database Navigation screen appears, choose

a thumbnail image of the desired title on the TV screen, then press ENTER. (A pg. 51)

● During HDD playback, the current title elapsed time is displayed

on the TV screen when ON SCREEN is pressed. However, each press of DISPLAY changes the time display on the front display panel as follows: Current title elapsed time N Disc remaining time N Current title remaining time N (back to the beginning)

● It is possible to play back on the DV deck and the HDD/DVD deck

simultaneously. However, either DVD or HDD can be played at the same time.

Reverse Search

4 steps

-60 -15 -3

-5

Reverse

Slow Motion

Play

3 steps

-1 1 1.5 3 5 15

1161

Slow Motion

3 steps

Normal

Forward Search

Play

5 steps

NOTE:

You can hear the (normal) audio track only during 1.5x speed search.

Still Picture/Frame-By-Frame Playback

1 Press W to pause during playback. 2 Press SLOW – (O) or SLOW + (N) to activate frame-by-

frame playback.

● Each press of SLOW – (O) or SLOW + (N) advances/

reverses the still picture frame by frame.

● To resume normal playback, press I.

Slow Motion

1 Press W to pause during playback. 2 Press SLOW – (O) or SLOW + (N) for 2 or more seconds.

● Each press of SLOW – (O) or SLOW + (N) increases the

slow motion speed for each direction.

Skip Search

During playback, press v.

● Each press initiates an approximately 30-second period of fast-

motion playback. Normal playback resumes automatically.

40 EN

BASIC OPERATIONS ON HDD DECK

One Touch Replay

You can move back the playback position slightly. Press w.

● Each press skips back for approximately 7 seconds and resumes

playback.

● Pressing while paused skips back for approximately 7 seconds

and resumes pause.

1.5x Speed Playback

You can play back a title quickly. The sound will also be played back faster than normal speed during 1.5x speed playback.

1.5x speed playback cannot be performed during recording on HDD or DV D.

1 Press O to locate the point to start 1.5x speed playback from. 2 Press I to resume playback. 3 Press N once.

● Pressing ON SCREEN displays AX1.5B on the top right corner of

the screen.

NOTE:

When the unit is connected with a digital audio device using an optional optical cable, set ADIGITAL AUDIO OUTB to APCM ONLYB. (A pg. 28)

Jump Search

You can locate a scene ahead or behind the current one by jumping scenes according to selected time intervals (A pg. 72) during playback (or Live Memory Playback). Press JUMP – or JUMP +.

● To advance forward or back, press JUMP – or JUMP +

repeatedly within 5 seconds of each press to continue jump.

● Depending on the time from where you want to start jump search,

● When you cannot advance any further (beginning or end of

program reached), the message AUNABLE TO GO BACK ANY MOREB appears on the screen and the on-air screen resumes. In such a case, press S, O or o.

Example:

Playback search when jump interval is set to 15 MIN jumps. Taking for instance, you want to start jump search 40 minutes after the beginning of the program. Pressing JUMP – or JUMP + will result in a jump to the scene at the 30 minutes point or 45 minutes point respectively as illustrated below. At the subsequent press, the scene will jump to the 15 minutes point or 1 hour point respectively, according to the selected time interval, which in this case is A15 MINB.

Time counter

0 min

15 min

30 min

40 min

45 min

1 h 15 min

1 h

Marking Positions To Play Back Again Later

It is possible to mark positions (up to 999 points) where you want to play back once again later, and start playback from a marked position. Marking onto the disc when recording is helpful to locate a start point when you play back the disc later.

To mark positions:

During playback, press MARK at positions you want to mark.

● AMARKB appears on the TV screen.

You can easily locate the marked positions using S or T when you play back the disc.

To delete the marked positions:

While paused, press S or T to locate a marked position you want to delete, then press MARK.

● Crossed AMARKB appears on the

TV screen, and the marked position is deleted.

NOTE:

When a monaural program changes to a stereo program while recording, a mark signal is automatically recorded.

Beginning of program

Current scene

End of program

Basic Playback

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

DV/HDD/DVD

DV lamp

SELECT

CABLE/DBS

BASIC OPERATIONS ON DV DECK

EN 41

1 Load a cassette. Make sure the window side is up, the rear

label side is facing you and the arrow on the front of the cassette is pointed toward the unit.

● Do not apply too much pressure when inserting.

● If the erase protection switch is set to ASAVEB, playback begins

automatically. It takes about 15 seconds until the playback picture appears. However, when APOWER SAVEB is set to AONB (A pg. 72), playback will not begin automatically even though a cassette with its erase protection switch set to ASAVEB is

inserted.

● The unit’s power comes on automatically.

2 Press DV/HDD/DVD SELECT on the unit repeatedly or DV on

the remote control so that the DV lamp lights up on the unit.

3 Find the program start point. If the tape is advanced past the

start point, press O. To go forward, press N.

4 Press I to start playback. 5 Press o to stop playback.

DVDTV

● To eject the cassette, press M (DV).

Clean the video heads using a dry cleaning cassette

- M-DV12CL - when:

● No picture during playback.

● Block noise appears during playback.

● AUSE CLEANING CASSETTEB appears on the screen.

NOTE:

The heads get dirty in the following cases:

● in an environment prone to extreme temperature or humidity

● in a dusty environment

● flaw, dirt or mould on video tapes

● continuous usage for a long time

Usable cassettes

● Cassettes marked P can be used with the DV deck.

NOTES:

● This unit does not support playback of DV tapes with HD format

recordings.

● When you record a tape on the DV deck with the recording speed

set to ALPB, it is recommended to play back that tape back on this DV deck. Digital video recorder from other manufacturers may not be able to play back the tape properly.

● It is possible to play back on the DV deck and the HDD/DVD deck

simultaneously. However, either DVD or HDD can be played at the same time.

Accidental erasure prevention

To prevent accidental recording on a recorded cassette, set its erase protection switch to ASAVEB. To record on it later, set the switch to ARECB.

Erase protection switch

42 EN

BASIC OPERATIONS ON DV DECK

Playback Features

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press DV/HDD/DVD SELECT on the unit repeatedly or DV on

the remote so that the DV lamp lights up on the unit.

CABLE/DBS

DVDTV

DISPLAY

AUDIO

ATTENTION:

In the search, still, slow-motion or frame-by-frame playback mode, a slight mosaic effect appears on screen.

Variable Speed Search

During playback, press N for forward variable speed search, or O for reverse variable speed search.

● Each press of the button increases the search speed for each

direction.

● To resume normal playback, press I.

Reverse

Slow Motion

1 step

Slow Motion

Reverse Search

3 steps

1 step

I N

Forward

Normal Play

Forward Search

3 steps

12412

Skip Search

During playback, press v.

● Each press initiates an approximately 30-second period of fast-

motion playback. Normal playback resumes automatically.

One Touch Replay

During playback, press w. The unit rewinds the picture a little (about 7 seconds) and resumes playback.

Next Function Memory

The Next Function Memory AtellsB the unit what to do after rewinding. Before continuing, make sure the unit is in the Stop mode.

For Automatic Start Of Playback

Press O, then press I within 2 seconds.

Soundtrack Selection

Your unit is capable of recording two soundtracks (L and R) and will play back the one you select.

During Playback Pressing AUDIO changes the soundtrack as follows:

TRACK

On-Screen Display

L+R Both sounds on the left channel and

the right channel are mixed and played back

L Sound on the left channel is played

back

R Sound on the right channel is played

back

To select the audio mode (SOUND1/SOUND2/MIX), refer to AAUDIO MODEB under ADV SET UPB (A pg. 71).

USE

Time Code

During recording, a time code is recorded on the tape. This time code is used to confirm the position on the tape when playing back or editing a tape.

1 Press DISPLAY until the time code on the tape appears on the

front display panel and the TV screen.

● Each time you press DISPLAY, the indication changes as

follows: Tape remaining time N Time code N Clock time N (Back to the beginning)

Still Picture/Frame-By-Frame Playback

1 Press W to pause during playback. 2 Press W to activate frame-by-frame playback.

● To resume normal playback, press I.

Slow Motion

1 Press W to pause during playback. 2 Press and hold W for 2 seconds, then release. Press W and

release again to return to still picture.

● Press N for forward slow motion or O for reverse slow

motion.

● To resume normal playback, press I.

LIVE MEMORY PLAYBACK ON HDD/DVD DECK

EN 43

Live Memory Playback

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press DV/HDD/DVD SELECT on the unit repeatedly to select

the HDD or DVD deck.

This unit records pictures onto the hard disk and DVD-RAM disc, instead of video tapes, then plays back the pictures recorded on the disc. This makes it possible to achieve high-speed writing and read-out that has not been possible with conventional VCRs, enabling recording and playback simultaneously.

High-speed spin

(High-speed writing)

Recording

It is called ALive Memory PlaybackB to start playback of the program being recorded, with a time-lag between a recording point and a playback point, as shown in the figure below.

Current playback point

(Live Memory Playback)

Current recording position

Playback continues

(Recording point)

Recording start point

Currently elapsed recording time

30 min.

Not only can this unit play back a program previously recorded while recording or timer recording another program, but the unit also allows you to play back from the beginning of a program while continuing to record the same program.

Playback (High-speed read-out)

Recording continues

1 hour

Recording/playback Status Display

CABLE/DBS

DVDTV

LIVE

NAVIGATION

Press NAVIGATION to display Library Database Navigation menu, then choose a program to play

A pg. 50)

back. (

ON SCREEN

Live Memory Playback status can be checked by pressing ON SCREEN to display the bar meter on the superimpose display. The current status is superimposed on the TV screen. ( using Live Memory playbackB)

LIVE CHECK

NOTES:

● Live Memory Playback could be performed approximately 30

seconds after recording has started on the DVD-RAM disc. However, for HDD, Live Memory Playback is possible right after recording has started.

● Although high-speed search up to approximately 30 seconds

before the current recording point is possible during Live Memory Playback, once the current recording point is reached, the unit resumes normal playback and maintains a delay of approximately 30 seconds so that recording and playback can continue.

● When using Live Memory Playback during timer recording,

playback continues even after the end of the recording.

● When using Live Memory Playback during timer recording on the

DVD-RAM disc, the next timer recording will be recorded to the HDD deck even though recording on the DVD deck has stopped. (A pg. 48, ARelief RecordingB)

● It is impossible to perform ITR even if you press R on the unit

during Live Memory Playback while in normal recording or RetroActive Recording. (A pg. 38) Press o to display the program being recorded, then perform ITR settings.

● It is possible to perform ITR during Live Memory Playback while

in temporary recording for Live Memory (HDD deck only). Press R to stop Live Memory Playback and activate normal recording, then perform ITR settings.

● It is impossible to perform ITR during Live Memory Playback

while in timer recording.

● Playback may be paused for a moment during Live Memory

Playback, which does not interfere with recording.

● Live Memory Playback cannot be performed while recording the

source from DV input. (A pg. 60, ADV Dubbing (HDD & DVD Deck Only)B)

● When LIVE CHECK is pressed to display the picture currently

being recorded, the picture size may not be correct.

● Press o or LIVE to stop Live Memory Playback.

● Live Memory Playback cannot be performed while the DVD deck

is recording as temporary recording on HDD stops during recording on DVD.

A pg. 16, AWhen

44 EN

LIVE MEMORY PLAYBACK ON HDD/DVD DECK

Buttons To Be Used During Live Memory Playback

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press HDD or DVD to select the desired deck for Live Memory

Playback.

CABLE/DBS

DVDTV

HDD

E G

A LIVE

Returns to on air program screen. When a confirmation message appears by pressing this button during timer programming or title editing, etc., follow the instruction to return to the previous screen.

B NAVIGATION

Displays Library Database Navigation menu. You can choose a title to play back.

C S

● Pressing once skips back to the beginning of the chapter being

played back.

● Pressing down for 2 or more seconds during playback reverses

playback at 5 times the normal speed while pressed. Releasing the button resumes normal playback.

Available only when paused

● Pressing down for 2 or more seconds reverses playback at 1/16

times the normal speed.

D T

● Pressing once skips forward to the beginning of the next

chapter being played back.

● Pressing down for 2 or more seconds during playback

advances playback at 5 times the normal speed while pressed. Releasing the button resumes normal playback.

Available only when paused

● Pressing down for 2 or more seconds advances playback at 1/

16 times the normal speed.

E O

● Each press of the button during playback advances the

playback speed in 5 steps in the reverse direction.

Available only when paused

● Each press of the button reverses the still picture frame by

frame.

● Pressing down for 2 or more seconds reverses playback at 1/16

times the normal speed. Then, each press of the button reverses slow-motion at 1/16 times, 1/4 times and 1/2 times the normal playback.

F H K

DVD

F N

● Each press of the button during playback advances the

playback speed in 4 steps in the forward direction.

Available only when paused

● Each press of the button advances the still picture frame by

frame.

● Pressing down for 2 or more seconds advances playback at 1/

16 times the normal speed. Then, each press of the button advances slow-motion at 1/16 times, 1/4 times and 1/2 times the normal playback.

G o

● Pressing once during Live Memory Playback or RetroActive

Recording returns to the screen on air.

● Pressing twice during recording stops recording and returns to

the screen on air.

H W

● Pressing once pauses playback (still picture playback).

● Pressing repeatedly advances the still picture frame by frame.

I JUMP –

Each press of the button during Live Memory Playback jumps back for the selected time interval and resumes playback. (A pg. 40, AJump SearchB)

J JUMP +

Each press of the button during Live Memory Playback jumps forward for the selected time interval and resumes playback. (A pg. 40, AJump SearchB)

K v

It is useful when skipping over unwanted sections.

● Pressing once skips forward for approximately 30 seconds and

resumes playback.

● Pressing repeatedly skips forward continuously as many times

as pressed.

L w

It is useful when watching sports programs, etc.

● Each press skips back for approximately 7 seconds and

resumes playback.

● Pressing repeatedly skips back for approximately 7 seconds

continuously as many times as pressed.

M LIVE CHECK

You can check, for example, if the program you are recording has already finished.

● Pressing once displays the picture currently being recorded and

the one being played back simultaneously.

● Pressing successively clears the Live Check window and

displays only the picture currently being played back.

LIVE MEMORY PLAYBACK ON HDD/DVD DECK

EN 45

Temporary recording for Live Memory (HDD deck only)

This unit automatically records the channel being received, within the specified range of time, to the reserved space on the hard disk. The time range can be set for 30 minutes, 1 hour, and 3 hours. (A pg. 71)

NOTE:

Previous temporary recordings will be overwritten since the unit is always recording the channel being received. Thus, it is not possible to play back TV programs recorded beyond the specified range of time since they are already overwritten. To avoid this in order to save titles, perform normal recording (A pg. 37), timer recording (A pg. 46, 48), or RetroActive Recording (See below).

About limitation on temporary recording

The temporary recording for Live Memory is canceled in the following cases, and will start all over again when it is to resume.

● When the power is turned off

● When the system is powered again after a power failure was

occurred

● When normal recording, timer recording or RetroActive

Recording is performed

● When the ALIVE MEMORYB setting is changed (A pg. 71)

● When tuner channel setting is performed (A pg. 22)

● When dubbing is performed by pressing DUBBING (A pg. 57)

● When ADVB is selected by pressing CH +/– (A pg. 60)

RetroActive Recording (HDD deck only)

You can start recording from the previous part of the channel you are currently watching (temporarily recorded on the background). (See ATemporary recording for Live Memory (HDD deck only)B above.)

1 Press S or O to locate the point to start recording from.

● Each press of O increases the reverse search speed.

2 Press R on the unit to start RetroActive Recording. Or while

holding R, press I on the remote control.

3 Press o twice to stop RetroActive Recording.

● The on-air screen resumes.

NOTES:

● You cannot use RetroActive Recording for channels other than

the channel you are currently watching.

● Recording speed is automatically set to FR65 mode when

RetroActive Recording is started.

● Temporarily recorded data prior to the beginning of RetroActive

Recording is erased when RetroActive Recording started.

Simultaneous Recording and Playback

You can play back the previous part of the channel you are recording or other programs available in the Library Database.

1 Press NAVIGATION. The Library Database Navigation screen

appears.

2 Press selection keys to select AORIGINALB, then press

ENTER.

3 Press selection keys to select the desired title, then press

ENTER.

● For DVD-RAM, playback starts from the beginning of the title if

ACONTINUOUS PLAYB in ADVD S ET UPB is set to AONB (A pg. 71).

4 Press selection keys to select the desired playback method

(ABEGINNINGB, ARESUMEB or AREPEATB ), then press ENTER.

● Playback of the selected title begins automatically.

5 Press o to stop playback.

● The on-air screen resumes.

NOTES:

● You can use various playback features during Live Memory

Playback.

● To stop simultaneous playback, press o. The on-air screen

resumes. To stop actual recording, press o twice again.

One Touch Replay

You can move back the playback position slightly during recording or Live Memory Playback. Press w.

8 DVD-RAM

● Pressing once during recording skips back for approximately 30

seconds and starts Live Memory Playback. While pressing once during Live Memory Playback skips back for approximately 7 seconds and resumes playback.

● Each subsequent press skips back for approximately 7 seconds

and resumes playback.

● Pressing while paused skips back for approximately 7 seconds

and resumes pause.

8 HDD

● Pressing during recording skips back for approximately 7

seconds and starts Live Memory Playback. While pressing during Live Memory Playback skips back for approximately 7 seconds and resumes playback.

● Each press skips back for approximately 7 seconds and resumes

playback.

● Pressing while paused skips back for approximately 7 seconds

and resumes pause.

Resuming Playback (HDD deck only)

You can resume playback of a TV broadcast you were recording or watching from the point you have paused.

1 Press W to pause a TV broadcast.

● Recording continues when recording.

2 Press I to start Live Memory Playback.

● Playback resumes from the paused position.

3 Press o to resume the on-air screen.

46 EN

TIMER RECORDING ON HDD/DVD DECK

VCR Plus+ Timer Programming

You can program this unit to timer record as many as 32 programs. With the VCR Plus+ system, timer programming is greatly simplified because each TV program has a corresponding code number which your unit is able to recognize. You can use the remote control to enter the PlusCode number.

● Make sure that the unit’s built-in clock is set properly.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

CABLE/DBS

DVDTV

0 – 9

PROG

ENTER

DISPLAY

Selection Keys

FGDE

RETURN

7 The PlusCode number you entered and the matching timer

recording information are displayed on the TV screen. Check the program data.

● To cancel this setting, press RETURN.

IMPORTANT:

Make sure the channel position number you wish to record is displayed; if not, see AChanging VCR Plus+ SettingB (A pg. 73) and set the Guide Channel number correctly.

8 Press selection keys to select the desired recording option as

required. Press selection keys to select the desired setting, then press ENTER.

● AINPUT NAMEB (A pg. 51, AModify Title NameB)

● ACATEGORYB (A pg. 52, AModify CategoryB)

● AWEEKLY/DAILYB (A pg. 47, AWeekly/Daily RecordingB)

● AREC MODEB (A pg. 34, ARecording ModeB)

9 Press selection keys to select AOKB, then press ENTER to

access the Program Confirmation screen.

10 Press selection keys to select AEXITB, then press ENTER to

complete timer programming.

● To program another timer, press DE to select ACONTINUEB,

then press ENTER.

● If APROGRAM OVERLAPPEDB appears on the TV screen,

delete or modify the programs.

NOTES:

● There may be cases that the VCR Plus+ Timer Programming

function prolongs the stop time of the programming.

● When two successive programs are recorded on a DVD-RW disc

with the VCR Plus+ Timer Programming function, the beginning of the second one may be left off the recording.

● If the copy limited program is received during timer recording, the

unit enters Record Pause mode. Recording starts again if it is switched to a recordable broadcast during the time you programmed.

1 Load a recordable disc if recording to DVD. 2 Press PROG to access the program top screen. 3 Press selection keys to select AVCR Plus+ PR.B, then press

ENTER.

● When APROGRAM FULL DELETE UNWANTED TIMER

PROGRAMSB appears on the TV screen, you need to cancel some of the reserved programs. (A pg. 49)

4 Press the number keys to

enter the PlusCode number of a program you wish to record.

Press selection keys to select the desired number key on the screen, then press ENTER. Repeat to enter all required

SELECT WITH @ THEN PRESS [ENTER]

PRESS [PROG] TO EXIT

PROG

EXIT

SELECT

ENTER

PROGRAM > VCR Plus+ PR. (1/2)

PLUS CODE NO.

1234

12 456 789

DELETE

RECORD TO DVD

DELETE ALL

CONFIRM

numbers.

● If you have made a mistake, press selection keys to select

ADELETEB or ADELETE ALLB, then press ENTER and input the correct number before you press ENTER again.

5 Press selection keys to select ARECORD TOB, then press

ENTER. Press selection keys to select the desired recording deck, then press ENTER.

6 Press selection keys to select ACONFIRMB, then press

ENTER.

● If the number you entered is invalid, APLUSCODE NO. ERROR

CONFIRM PLUSCODE NO. THEN RETRYB appears on the TV screen. Input a valid PlusCode number.

● If AGUIDE PROGRAM IS NOT SET SET GUIDE PROGRAM

THEN RETRYB appears on the TV screen, set Guide Channel Numbers manually. (A pg. 73)

IMPORTANT:

If you have moved to a different area or if a broadcasting station’s channel number has been changed, the wrong channel number will be displayed on the VCR Plus+ program screen in step 7. When this happens, set the correct Guide Channel number for that station. (A pg. 73, AChanging VCR Plus+ SettingB)

Weekly/Daily Recording

You can record programs with one of the following weekly/daily timer settings.

For the HDD deck

When you select a mode other than ONCE, the space on the hard disk drive is saved for new recordings by overwriting previous recordings. To prevent loss of a needed recording, backup programs you wish to save by dubbing them to DVD discs before overwriting previous recordings. Or save the title of weekly/daily programs to avoid overwriting of a previous week/day. (A pg. 49)

ONCE (One Time Recording)

In this mode a program will not be automatically overwritten.

WEEKLY (OVERWRITE) (Weekly Recording/Weekly Overwrite)

When the set weekly program is broadcast, the program recorded last week is automatically deleted and overwritten by the new program. Save the title of each program you wish to save, then the recorded program is saved and will not be overwritten by the new program.

This week’s drama

Overwritten

MON-SUN (FOR A WEEK)/ MON-SAT (FOR A WEEK)/ MON-FRI (FOR A WEEK) (Daily Recording/Weekly Overwrite)

When the set weekly program is broadcast, the program recorded on the same day last week is automatically deleted and overwritten by the new program. Save the title of each program you wish to save, then the recorded program is saved and will not be overwritten by the new program.

This

Overwritten

week

Last

week

Last week’s drama

MON TUE WED THU FRI

TIMER RECORDING ON HDD/DVD DECK

EN 47

MON-SUN (OVERWRITE)/ MON-SAT (OVERWRITE)/ MON-FRI (OVERWRITE) (Daily Recording/Daily Overwrite)

When the set daily program is broadcast, yesterday’s program is automatically deleted and overwritten by the new program. Save the title of each program you wish to save, then the recorded program is saved and will not be overwritten by the new program.

Overwritten

For the DVD deck

Tuesday’s program

Monday’s program

ONCE (One Time Recording) WEEKLY (Weekly Recording) MON-SUN/ MON-SAT/ MON-FRI (Daily Recording)

48 EN

TIMER RECORDING ON HDD/DVD DECK

Manual Timer Programming

You can program this unit to timer record as many as 32 programs. If you do not know the PlusCode number for the program you wish to record, use the following procedure to set your unit to timer record the program.

● Make sure that the unit’s built-in clock is set properly.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

CABLE/DBS

DVDTV

PROG

ENTER

Selection Keys

FGDE

8 Press selection keys to select ASOURCEB, then press ENTER.

Press FG to select the desired source.

9 Press selection keys to select ACHB, then press ENTER. Press

FG to select the desired channel.

10 Press selection keys to select ACONFIRMB, then press

ENTER.

11 Set the other recording options as required.

● Refer to step 8 in AVCR Plus+ Timer ProgrammingB

(A pg. 46).

12 Press selection keys to

select AOKB, then press ENTER to access the Program Confirmation screen.

13 Press selection keys to

select AEXITB, then press ENTER to complete timer programming.

● To program another timer, press selection keys to select

ACONTINUEB, then press ENTER.

● If APROGRAM OVERLAPPEDB appears on the TV screen,

delete or modify the programs.

NOTES:

● When two successive programs are recorded on a DVD-RW disc

with Manual Timer Programming function, the beginning of the second one may be left off the recording.

● If the copy limited program is received during timer recording, the

unit enters Record Pause mode. Recording starts again if it is switched to a recordable broadcast during the time you programmed.

SELECT WITH @ THEN PRESS [ENTER]

PRESS [PROG] TO EXIT

PROG

EXIT

01/08/03 WED 10:30PM - 11:0 0PM GARDENING

INPUT NAME

NAVIGATION ON HDD/DVD DECK

Library Database Navigation

The Library Database Navigation enables you to search and select the desired titles recorded on the HDD deck and the DVD deck very easily. You can record up to 99 titles on a disc. Each time a title is recorded, the information of the title is registered for the Library Database Navigation automatically. So, you can confirm the information of the titles recorded with the Library Database Navigation screen. And, you can also select one of the titles recorded using the Library Database Navigation. The following screen appears as the Library Database Navigation screen when you press NAVIGATION. You can move the arrow to select the desired position on the screen by pressing selection keys on the remote control.

NAVIGATION > ORIGINAL

0026 143 MIN[FISH WORLD ]

EXIT

25/12/03 THU 10:00AM - 10:15AM

FROG WORLD

ENTER

SELECT

SELECT WITH @ THEN PRESS [ENTER]

PRESS[NAVIGATION] TO EXIT

NAVIGATION

A Playback screen

(Indicates currently received TV program.)

B Guidance for operations C Scroll bar

(Appears when there are over nine registered titles (or play lists). The scroll bar only indicates that there are more titles (or play lists) hidden off the current screen display. To show hidden titles (or play lists), press selection keys repeatedly.)

D Recording information for the title indicated by the arrow E Index list

(Thumbnail still of each title) Thumbnail still is not to be played back.

F Index

:Indicates no index is registered. :Indicates title in standby for timer recording. :Indicates no title is registered.

G Icons

(Indicate the record condition of each title.)

[HOBBY]

3PR.

F G

Using Library Database Navigation system, you can easily modify registered information, edit the title or play list, as well as search for the beginning of each title.

About registration of information

The following information is automatically registered for each title when ordinary recording or timer recording is performed, then stored in an area specified on the unit.

● index* (reduced pictures to show program titles)

● program title*

● category*

● date and time

● channel

● recording mode

● length of recording time

The items marked with an asterisk (*) can be easily modified and registered again after recording by using Library Database Navigation system.

The limitations of registration

You can register information up to 99 titles for the DVD deck and 200 titles for the HDD deck. When the amount of information is at the limits of registration, you cannot record new titles any more. In this case, you need to delete old titles to register new ones. (A pg. 52)

NOTES:

● Once a DVD-R/RW (Video mode) disc has been finalized, the

display for original does not appear. Only display for library appears.

● When a copy-once title recorded on the HDD is dubbed to a DVD

disc (DVD-RAM/-RW (VR mode)), the original data will be moved from the HDD to the DVD disc. In additional, the title that was moved to the DVD disc will become a copy-protected title, and the icon changes from to .

● Sound of received channel may be interrupted while the Library

Database Navigation screen is displayed.

● The order of index which are displayed by pressing DUBBING

differs from the images displayed by pressing NAVIGATION or EDIT.

● You cannot perform timer recording during editing of thumbnail

images or play lists by pressing EDIT. Press EDIT to clear the Editing screen before performing timer recording.

The Icons and their meanings

This title is write-protected.

This title was recorded with timer recording.

This title is Weekly Recording/Weekly Overwrite.

This title is Daily Recording/Daily Overwrite.

NEW

This title is Daily Recording/Weekly Overwrite.

This title has not been played back.

This title is copy-protected.

This title can only be recorded once (copy-once title).

NAVIGATION ON HDD/DVD DECK

EN 51

Scan For Beginning Of Title

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press HDD or DVD to choose the corresponding deck.

● Load a DVD disc to scan.

CABLE/DBS

DVDTV

HDD

CANCEL

ENTER

You can scan the beginning of the title easily with the Library Database Navigation.

1 Press NAVIGATION. The Library Database Navigation screen

appears.

2 Press selection keys to select AORIGINALB, then press

ENTER.

3 Press selection keys to select

the index (small pictures) of the desired title, then press ENTER.

● When you want the plural titles

to be played back continuously, press MEMO after selecting the desired title. The numbers of the playback order appear on the index. You can select up to 8 titles.

● When you want to correct the order, move the arrow to the

desired index and press MEMO. The number disappears and the unit re-numbers the other programs automatically.

● When you want to cancel the order, press CANCEL(L).

4 Press selection keys to select

ABEGINNINGB, then press ENTER.

● To resume playback from the

point where playback was previously stopped, press selection keys to select ARESUMEB, then press ENTER.

● To repeat playback of a selected title, press selection keys to

select AREPEATB, then press ENTER.

5 Press W to pause playback.

● To resume normal playback, press I.

6 Press o to stop playback.

DVD

MEMO

EDIT

NAVIGATION

Selection Keys

FGDE

SELECT WITH @ THEN PRESS [ENTER]

PRESS[NAVIGATION] TO EXIT

ENTER

NAVIGATION

EXIT

SELECT

SELECT WITH @ THEN PRESS [ENTER]

PRESS [NAVIGATION] TO EXIT

ENTER

NAVIGATION

EXIT

SELECT

NAVIGATION > ORIGINAL

0026 143 MIN[FISH WORLD ]

25/12/03 THU 10:00AM - 10:15AM

FROG WORLD

NAVIGATION > ORIGINAL

25/12/03 THU

10:00AM - 10:15AM FROG WORLD

SELECT HOW TO PLAY BACK

BEGINNING RESUME REPEAT

TVSP3

[HOBBY]

3TV

Edit Original Information

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press HDD or DVD to choose the corresponding deck.

● Load a DVD disc to modify.

ATTENTION:

● It is not possible to modify discs recorded on DVD units from

other manufacturers.

● You cannot perform timer recording during editing the index by

pressing EDIT. Press EDIT to clear the editing screen before performing timer recording.

Modify Index

1 Press EDIT. The Editing screen appears. 2 (DVD deck only) Press selection keys to select AMODIFYB

under AORIGINAL/PLAY LISTB, then press ENTER.

3 Press selection keys to select AMODIFYB under AORIGINALB,

then press ENTER.

4 Press selection keys to select a title you want to modify, then

press ENTER.

5 Press selection keys to select AINDEXB, then press ENTER. 6 Press I to start playback. Press O or N to search for the

picture from the title, then press W.

● The pictures of the title appear

on the left window.

7 Confirm the arrow is on

AREPLACEB, then press

ENTER to register new index. New index appears on the right window.

● When you press ENTER with

the arrow on ARETURNB you can return to the previous screen.

8 Press EDIT to return to the normal screen.

Modify Title Name

1 Perform steps 1 – 4 of AModify IndexB above before continuing. 2 Press selection keys to select ANAMEB, then press ENTER. 3 Press selection keys to select

the desired letter or command, then press ENTER. Repeat this process to complete the name.

● To correct a letter, press

selection keys to select ADELETEB, then press ENTER.

● You can enter the letters up to

64.

4 Press selection keys to select ASAVEB, then press ENTER. 5 Press EDIT to return to the normal screen.

EDITING > MODIFY INDEX

25/12/03 THU 10:00AM - 10:15AM

FROG WORLD SP

0:01:03PROG. 1

SELECT IMAGE TO REPLACE WITH

0026 64 MIN[FISH WORLD ]

25/12/03 THU 10:00AM - 10:15AM

FROG WORLD

SELECT WITH @ THEN PRESS [ENTER]

PRESS [EDIT] TO EXIT

FROG

A B C D E F a b c d e f 1 2 3 G H I J K L g h i j k l 4 5 6 M N O P Q R m n o p q r 7 8 9 S T U V W X s t u v w x 0 + Y Z y z * / =

! " # $ % & ; < > ? @ [ | } ~ ' ( ) , . : \ ] ^ _ ` {

ENTER

EDIT

EXIT

SELECT

3TV

[OTHERS]

INDEX

ON REMOTE

RETURNREPLACE

EDITING > MODIFY NAME

ORLD

CANCEL DELETE SAVE

[HOBBY]

3TV

52 EN

NAVIGATION ON HDD/DVD DECK

Modify Category

1 Perform steps 1 – 4 of AModify IndexB (A pg. 51) before

continuing.

2 Press selection keys to select ACATEGORYB, then press

ENTER.

3 Press selection keys to select

the desired category, then press ENTER.

4 Press EDIT to return to the

normal screen.

SELECT WITH @ THEN PRESS [ENTER]

PRESS [EDIT] TO EXIT

EDIT

EXIT

EDITING > MODIFY CATEGORY

0026 64 MIN[FISH WORLD ]

25/12/03 THU 10:00AM - 10:15AM

FROG WORLD

MOVIES MUSIC DRAMA

ANIMATION

NEWS WEATHER EDUCATION

ENTER

HOBBY

SELECT

SPORTS

ENTERTAINMEN T

[HOBBY]

DOCUMENTARY

ART

3TV

Protect Title (DVD-RAM & DVD-RW (VR mode) only)

You can protect titles to prevent accidental erasure of the important titles.

1 Perform steps 1 – 2 of AModify IndexB (A pg. 51) before

continuing.

2 Press selection keys to select APROTECTB, then press

ENTER.

3 Press selection keys to select a title you want to protect, then

press ENTER.

4 Press selection keys to select APROTECTB, then press

ENTER. AB appears.

● To cancel the protection, repeat 3 – 4 again. In step 4, select

ACANCEL PROTECTB, then press ENTER.

5 Press EDIT to return to the normal screen.

NOTE:

All the titles on a disc will be deleted once the disc is formatted even if they are protected titles.

Delete Title

You cannot record any more with Library Database Navigation once the registered titles on the disc reach 99 titles for the DVD deck and 200 titles for the HDD deck. Deleting unnecessary titles after dubbing or other operations can increase remaining time and available recording capacity. (For DVD-R discs, although it is possible to delete recorded titles, available recording capacity does not increase.) The deleted title is never resumed. Play lists and title information in the unit’s library are also deleted.

1 Press EDIT. The Editing screen appears. 2 (DVD deck only) Press selection keys to select AMODIFYB

under AORIGINAL/PLAY LISTB, then press ENTER.

3 Press selection keys to select ADELETEB under AORIGINALB,

then press ENTER.

4 Press selection keys to select a title you want to delete, then

press ENTER.

5 Press selection keys to select ADELETEB, then press ENTER.

● When you cancel the deletion, select ACANCELB, then press

ENTER.

6 Press EDIT to return to the normal screen.

Delete Unwanted Part Of The Title (DVD-RAM & DVD-RW (VR mode) only)

You can delete unwanted part of the title.

1 Perform steps 1 – 2 of AModify IndexB (A pg. 51) before

continuing.

2 Press selection keys to select ADEL SCENB, then press

ENTER.

3 Press selection keys to select a title whose unwanted part you

want to delete, then press ENTER.

4 Press I to start playback. Press O or N to find the point

where you want the deletion to begin, then press W.

5 Confirm the arrow is on AINB,

then press ENTER.

6 Press I to start playback.

Press O or N to find the point where you want the deletion to end, then press W.

7 Press selection keys to select

AOUTB, then press ENTER.

● Select APREVIEWB, then press

ENTER to preview the edited title.

8 Press selection keys to select AOKB, then press ENTER.

● If you do not want to delete the scene, press RETURN.

To modify the points

A Press RETURN. B Repeat steps 4 – 8 as necessary.

9 Press selection keys to select ADELETEB, then press ENTER.

The selected scene is deleted.

● To cancel the deletion, press DE to select ACANCELB, then

press ENTER.

10 Press EDIT to return to the normal screen.

NOTES:

● There may be a discrepancy of several seconds between the

scene you intend to edit, and the scene which is actually edited.

● Available recording capacity may not match the deleted part after

deletion.

EDITING > ORIGINAL/DEL SCENE

21/12/03 SUN 5:30AM - 8:00AM

RALLY CAR SP

0:01:03

PROG. 1

SELECT SCENE TO DELETE WITH

IN OUT PREVIEW OK

TV 12

[OTHERS]

0: 05:15

OUT

0: 06:15

ON REMOTE

NAVIGATION ON HDD/DVD DECK

EN 53

Divide Title (HDD deck only)

1 Press EDIT. The Editing screen appears. 2 Press selection keys to select ADIVIDEB, then press ENTER. 3 Press selection keys to select a title to divide, then press

ENTER.

4 Press I to start playback. Press O or N to locate a point to

divide, then press W.

5 Confirm the arrow is on ADIVIDEB, then press ENTER.

● The first picture (start) of the newly created title appears in the

bottom right window.

● Select APREVIEWB, then press ENTER. The first several

seconds of the newly created title is played back, then the playback pauses at the dividing point.

● To undo the division, press selection keys to select ARETRYB,

then press ENTER. Repeat the above procedure to locate another point to divide.

6 Press selection keys to select AOKB, then press ENTER. 7 Press selection keys to select ADIVIDEB, then press ENTER.

● Select ACANCELB, then press ENTER to return to the previous

screen.

8 Press EDIT to return to the normal screen.

NOTE:

There may be a discrepancy of several seconds between the scene you intend to edit, and the scene which is actually edited.

Modify Chapter (HDD, DVD-RAM & DVD-RW (VR mode) only)

You can create and delete chapter marks in titles.

1 Perform steps 1 – 4 of AModify IndexB (A pg. 51) before

continuing.

2 Press selection keys to select ACHAPTERB, then press

ENTER.

3 Press I to start playback.

Press O or N, then press W at the positions you want to mark.

4 Press selection keys to select

AMARKB, then press ENTER.

● To undo the marking, press

selection keys to select ARETRYB, then press ENTER.

● Repeat the above steps 3 and 4 to locate another point to mark.

5 Press S or T to select one chapter you want to delete,

press selection keys to select AERASEB, then press ENTER.

● To undo the deletion, press selection keys to select ARETRYB,

then press ENTER.

6 Press EDIT to return to the normal screen.

NOTE:

There may be a discrepancy of several seconds between the scene you intend to edit, and the scene which is actually edited.

EDITING > MODIFY CHAPTER

CHAPTER 03/10

0:07:01

01 00: 00: 00 02 00: 05: 30 03 00: 07: 00 04 00 :30 :00

MARK

ERASE RETRY RETURN

Edit Play List Information

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press HDD or DVD to choose the corresponding deck.

● Load a DVD disc to modify.

ATTENTION:

● It is not possible to modify discs recorded on DVD units from

other manufacturers.

● You cannot perform timer recording during editing the index by

pressing EDIT. Press EDIT to clear the editing screen before performing timer recording.

CABLE/DBS

DVDTV

HDD

CANCEL

ENTER

S O

Play List

It is a collection of the scenes. A play list can be freely edited and played back without ever changing any original recording data. Using the random access of a disc (which allows video data to be instantly read no matter where it is on the disc), a play list includes information such as the timer counter for the playback start point and end point, indexes for checking the contents of recorded data, category information, and more. Playback according to a play list you have created allows you to enjoy various combinations of video images from a single title.

DVD

MEMO EDIT

NAVIGATION

Selection Keys

DFGE T

I N

54 EN

NAVIGATION ON HDD/DVD DECK

Create Play List

1 Press EDIT. The Editing screen appears. 2 (DVD deck only) Press selection keys to select AMODIFYB

under AORIGINAL/PLAY LISTB, then press ENTER.

3 Press selection keys to select ACREATEB, then press ENTER. 4 Press selection keys to select a title that includes scenes to be

included in a play list, then press ENTER.

5 Press I to start playback. Press O or N to find the point

where you want the created play list to begin, then press W.

6 Confirm the arrow is on AIN/

OUTB, then press ENTER.

● The edit-in time is displayed on

the screen.

● To undo, press selection keys

to select ARETRYB, then press ENTER.

7 Press I to start playback.

EDITING > PLAY LIST/CREATE

PRO. 1

0: 00:15

IN OUT

IN/OUT

SEL. TITLE

TOTAL TIME

SCENE

1 PRO.1

MODIFY MOVE PREVIEW

DELETE RETRY OK

00: 00 :00

PAGE

1/1

Press O or N to find the point where you want the created play list to end, then press W.

8 Confirm the arrow is on AIN/OUTB, then press ENTER.

● The edit-out time is displayed on the screen.

● The edit-out point must come after the edit-in point.

● Select APREVIEWB, then press ENTER to preview the play list.

9 Press selection keys to select AOKB, then press ENTER. 10 Press selection keys to select AEXITB, then press ENTER 11 Press EDIT to return to the normal screen.

NOTES:

● There may be a discrepancy of several seconds between the

scene you intend to edit, and the scene which is actually edited.

● The title, index and category of the play list can be modified in the

same way as AORIGINALB. (A pg. 51)

● You can modify the play list that has just been created here by

adding, moving, or deleting unwanted parts to create a digest edition, etc.

Edit Scenes

1 Press EDIT. The Editing screen appears. 2 (DVD deck only) Press selection keys to select AMODIFYB

under AORIGINAL/PLAY LISTB, then press ENTER.

3 Press selection keys to select AMODIFYB under APLAY LISTB,

then press ENTER.

4 Press selection keys to select a play list to modify, then press

ENTER.

5 Press selection keys to select ASCENEB, then press ENTER. 6 Press selection keys to select AMODIFYB, then press ENTER. 7 Press selection keys to select the start or end point of a scene

to modify, then press ENTER.

8 Perform steps 5 – 11 of ACreate Play ListB above.

Add scenes

1 Perform steps 1 – 5 of AEdit ScenesB on the left column before

continuing.

2 Press selection keys to select ASEL. TITLEB, then press

ENTER.

3 Perform steps 4 – 11 of ACreate Play ListB on the left column.

Move Scenes

1 Perform steps 1 – 5 of AEdit ScenesB on the left column before

continuing.

2 Press selection keys to select AMOVEB, then press ENTER. 3 Press selection keys to select a scene to move, then press

ENTER.

4 Press selection keys to select another scene to which the

scene is to be moved, then press ENTER.

● To cancel the move, press selection keys to select ARETRYB,

then press ENTER.

5 Perform steps 9 – 11 of ACreate Play ListB on the left column.

Delete Scenes

1 Perform steps 1 – 5 of AEdit ScenesB on the left column before

continuing.

2 Press selection keys to select ADELETEB, then press ENTER. 3 Press selection keys to select a scene to delete, then press

ENTER.

4 Perform steps 9 – 11 of ACreate Play ListB on the left column.

Play Back Play List

1 Press NAVIGATION. The Library Database Navigation screen

appears.

2 Press selection keys to select APLAY LISTB, then press

ENTER.

3 Press selection keys to select

the index (small pictures) of the desired play list, then press ENTER.

● When you want the plural play

lists to be played back continuously, press MEMO after selecting the desired play

SELECT WITH @ THEN PRESS [ENTER]

PRESS [NAVIGATION] TO EXIT

NAVIGATION

EXIT

lists. The numbers of the playback order appear on the index. You can select up to 8 play lists.

● When you want to correct the order, move the arrow to the

desired index and press MEMO. The number disappears and the unit re-numbers the other play lists automatically.

● When you want to cancel the order, press CANCEL(L).

4 Press selection keys to select ABEGINNINGB, then press

ENTER. The playback starts.

● Upon completing play list playback, the normal screen will

resume.

● The normal screen will also resume when o is pressed to stop

play list playback.

SELECT

ENTER

NAVIGATION > PLAY LIST

0026

026 CREATED 26/12/03 FRI

TEDDY BEAR 25/12

001 002 003

004 005 006

007 008 009

143 MIN[FISH WORLD ]

[MOVIES]

NAVIGATION ON HDD/DVD DECK

EN 55

Delete Play List

1 Press EDIT. The Editing screen appears. 2 (DVD deck only) Press selection keys to select AMODIFYB

under AORIGINAL/PLAY LISTB, then press ENTER.

3 Press selection keys to select ADELETEB under APLAY LISTB,

then press ENTER.

4 Press selection keys to select one play list you want to delete,

then press ENTER.

5 Press selection keys to select ADELETEB, then press ENTER.

● When you cancel the deletion, select ACANCELB, then press

ENTER.

6 Press EDIT to return to the normal screen.

NOTE:

Even if a play list is deleted, the titles recorded and the library information are not affected at all.

Modify Index

A Perform steps 1 – 4 of AEdit ScenesB (A pg. 54) before

continuing.

B Perform steps 5 – 8 of AModify IndexB (A pg. 51).

Modify Play List Name

A Perform steps 1 – 4 of AEdit ScenesB (A pg. 54) before

continuing.

B Perform steps 2 – 5 of AModify Title NameB (A pg. 51).

Modify Category

A Perform steps 1 – 4 of AEdit ScenesB (A pg. 54) before

continuing.

B Perform steps 2 – 4 of AModify CategoryB (A pg. 52).

Navigate Library Information

Title information can be registered in the unit’s memory for up to 600 DVD discs, 2,000 titles. It is helpful when finding a desired title (or play list) by sorting according to the sort options registered during (or after) recording.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press HDD or DVD to choose the corresponding deck.

CABLE/DBS

DVDTV

HDD

ENTER

Scan For Title From Library

1 Press NAVIGATION. The Library Database Navigation screen

appears.

2 Press selection keys to select

the appropriate sort button to sort the information, then press ENTER. ADATEB:

Sort by date

ADISC No.B:

Sort by disc number

ACATEGORYB:

Sort by category

ANAMEB:

Sort by name

● ADATEB and ADISC No.B are available for the DVD deck only.

3 Press selection keys to select the desired title, then press

ENTER.

● For HDD deck, playback begins automatically after the selected

title is located.

● For DVD deck, the title information will be displayed after the

selected title is located. However, playback will not begin automatically.

NOTE:

If a disc registered in the library is recorded or modified on DVD units from other manufacturers, it may become impossible to operate properly.

DVD

NAVIGATION

Selection Keys

FGDE

SELECT WITH @ THEN PRESS [ENTER]

PRESS [NAVIGATION] TO EXIT

ENTER

NAVIGATION

EXIT

SELECT

NAVIGATION

ORIGINAL

DVD NAVIGATION

DVD LIBRARY

DATE

Playback With MP3/WMA/JPEG Navigation

This unit can play back discs that MP3/WMA sound files and JPEG image files taken with digital still cameras or other devices are recorded. The MP3/WMA/JPEG Navigation enables you to search and select the desired files recorded on CD-R/RW or CD-ROM discs very easily.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Press DVD to select the DVD deck.

NAVIGATION > ORIGINAL

GROUP : 001/100 TRACK: 001/100 IT’S SHOWTIME!!/B’z

ROOT CLASSIC

CLUB DANCE

EUROPE

FOREIGN GROUP

FOREIGN ROCK

001.

IT’S SHOWTIME! !/ B’z

002.

ONLYFLOWER IN THE WORLD/ SMAP

003.

SEXY GUY/GOMAKI

004.

HEY?/AYAYA

005.

DOOR TO TOMORROW/I WISH

REASON/ASAMI

006.

007.

DIE ANOTHER DAY/JAMES BOND

A Selected group number/total number of groups on the disc B Selected file number/total number of files in the group that

contains the selected file

C Elapsed time (MP3/WMA) D Name of the selected file E Group name F Selected file

0: 07: 01

Locating The Desired Group And Tracks

1 Load a disc. 2 Press NAVIGATION. 3 Press selection keys to select AORIGINALB, then press

ENTER.

4 Press selection keys to select

the desired group, then press ENTER.

● A list of files in the selected

group appears.

5 Press selection keys to select

the desired item, then press ENTER. The unit starts playback from the selected item.

● The unit stops when all items

in the selected group are played back.

NOTES:

● If you press SELECT(I) instead of ENTER in step 4, the unit

starts playback from the first file of the group.

● JPEG files are played back as a slide show at the set intervals.

(A pg. 32)

● If a file name includes any 2-byte character, the unit may not

show the file name correctly.

● The order of the groups and items shown in steps 4 and 5 may

differ from the order shown on your PC.

NAVIGATION > ORIGINAL

GROUP : 001/100 TRACK : 001/100 IT’S SHOWTIME!!/B’z

ROOT CLASSIC

CLUB DANCE

EUROPE

FOREIGN GROUP FOREIGN ROCK

NAVIGATION > ORIGINAL

GROUP : 001/100 TRACK : 001/100 IT’S SHOWTIME!!/B’z

ROOT CLASSIC

CLUB DANCE

EUROPE

FOREIGN GROUP

FOREIGN ROCK

IT’S SHOWTIME!!/B’z

001.

ONLY FLOWER IN THE WORLD/SMAP

002.

SEXY GUY/GOMAKI

003.

HEY?/AYAYA

004.

DOOR TO TOMORROW/I WISH

005.

REASON/ASAMI

006.

007.

DIE ANOTHER DAY/JAMES BOND

001.

IT’S SHOWTIME!!/B’z

002.

ONLY FLOWER IN THE WORLD/SMAP

003.

SEXY GUY/GOMAKI

004.

HEY?/AYAYA

005.

DOOR TO TOMORROW/I WISH

REASON/ASAMI

006.

007.

DIE ANOTHER DAY/JAMES BOND

0: 07: 01

0:07:01

NOTES:

● If there are more than 100 files, the rest of the files are not

displayed. In this case, press ON SCREEN to display them on the TV screen.

● If both MP3 files and WMA files are recorded on the same disc,

WMA files cannot be played back as they are not displayed on the navigation screen.

Dubbing

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

CABLE/DBS

DVDTV

HDD

UBBING

ENTER

R o

NOTES:

● It is not possible to dub copy-protected contents. An error

message will appear on the TV screen.

● It is not possible to dub simultaneously when timer

programming is set. Select either dubbing or timer programming.

● The order of the index which is displayed by pressing

DUBBING differs from the images displayed by pressing NAVIGATION or EDIT.

High Speed Dubbing (From HDD To DVD)

It is possible to dub the original recordings and/or play lists on the HDD deck to DVD discs. The dubbing is performed in high speed, keeping the original transfer rate.

NOTES:

● After accessing the Dubbing Menu screen, it is not possible to

take out a disc.

● It is not possible to dub copy-once titles in Video mode.

● When dubbing a copy-once title, the data will be moved from

HDD to DVD upon completing dubbing.

● When you cancel dubbing a copy-once title during dubbing, the

original recording on the HDD deck remains and the title copied to a DVD disc is deleted.

● It is not possible to dub play lists which contain copy-once titles.

● It is not possible to dub the following programs to DVD-R/RW disc

(Video mode):

● which contains more than one audio language.

● which is on the play list.

● which is edited (also RetroActive Recording).

● which is recorded in LP mode or FP155-FP240 mode.

Recording may not be performed in the highest speed depending

●

on the characteristics of the disc used.

1 Load a recordable disc. 2 Press DUBBING to access the Dubbing Menu screen. 3 Press selection keys to select AHDDNDVD B, then press

ENTER.

4 Press selection keys to select AHIGH SPEEDB, then press

ENTER.

DVD

MARK

Selection Keys

FGDE

EDITING

EN 57

5 Press selection keys to select indexes (small pictures) of

desired original recordings and/or play lists, then press MARK. After selecting all indexes you want to dub, press ENTER.

● You can select up to 8 original recordings and/or play lists.

● The recordable time of the disc is displayed on the bar meter.

For details, refer to AAbout Disc Remaining DisplayB (A pg. 59).

6 Press selection keys to select AEXECUTEB, then press

ENTER to start dubbing.

NOTES:

● Play lists are dubbed as programs.

● In Video mode, if the selected play list includes the scenes

recorded in the different transfer rate, the dubbing is performed in the highest transfer rate of the scenes in the selected play list.

● During dubbing, it is not possible to play back on HDD or DVD, or

to set timer programming.

● It is not possible to discontinue dubbing once it has been started.

Just Dubbing (From HDD To DVD)

By using Just Dubbing function, when dubbing all selected original recordings and/or play lists, the unit automatically sets the appropriate recording mode depending on the combination of the total time of the selected recordings and/or play lists to be dubbed and the available disc space.

1 Load a recordable disc. 2 Press DUBBING to access the Dubbing Menu screen. 3 Press selection keys to select AHDDNDVDB, then press

ENTER.

4 Press selection keys to select AJUSTB, then press ENTER. 5 Perform steps 5 – 6 of AHigh Speed Dubbing (From HDD To

DVD )B.

NOTES:

● Play lists are dubbed as programs.

● In Video mode, if the selected play list includes the scenes

recorded in the different transfer rate, the dubbing is performed in the highest transfer rate of the scenes in the selected play list. However, the lower transfer rate cannot be dubbed in the higher transfer rate.

● The recordable time of the disc is displayed on the bar meter. For

details, refer to AAbout Disc Remaining DisplayB (A pg. 59).

● During dubbing, it is not possible to play back on HDD or DVD, or

to set timer programming.

● It is not possible to discontinue dubbing once it has been started.

Manual Dubbing (From HDD To DVD)

It is possible to perform dubbing in the desired transfer rate.

1 Load a recordable disc. 2 Press DUBBING to access the Dubbing Menu screen. 3 Press selection keys to select AHDDNDVDB, then press

ENTER.

4 Press selection keys to select AMANUALB, then press ENTER. 5 Perform step 5 of AHigh Speed Dubbing (From HDD To DVD)B.

The Manual Dubbing screen appears.

6 Press selection keys to select AREC MODEB, then press

ENTER. Press selection keys to select the desired option, then press ENTER.

7 Press G to select ACONFIRMB, then press ENTER. 8 Press selection keys to select AEXECUTEB, then press

ENTER to start dubbing.

NOTES:

● In Video mode, if the selected play list includes the scenes

● The recordable time of the disc is displayed on the bar meter. For

details, refer to AAbout Disc Remaining DisplayB (A pg. 59).

● During dubbing, it is not possible to play back on HDD or DVD, or

to set timer programming.

● It is not possible to discontinue dubbing once it has been started.

58 EN

EDITING

Dubbing From HDD To DV

It is possible to perform dubbing from the HDD deck to the DV deck.

1 Load a Mini DV cassette with the erase protection switch set to

ARECB.

2 Press DUBBING to access the Dubbing Menu screen. 3 Press selection keys to select AHDDNDVB, then press

ENTER.

4 Press selection keys to select indexes (small pictures) of

desired original recordings and/or play lists, then press MARK. After selecting all indexes you want to dub, press ENTER.

● You can select up to 8 original recordings and/or play lists.

5 Press selection keys to select ASELECT RECORDING

MODEB, then press ENTER. Press FG to select the desired option, then press ENTER.

6 Press selection keys to select ASELECT SOUND MODEB,

then press ENTER. Press selection keys to select the desired option, then press ENTER.

7 Press G to select ACONFIRMB, then press ENTER. The

confirmation screen appears.

8 Press DV so that the DV lamp lights up on the unit. 9 Press I to locate the point from where you want to start

dubbing, press o or W then press R and W simultaneously so that the DV deck enters the record pause mode.

10 Press HDD so that the HDD lamp lights up on the unit.

● The dubbing screen will appear.

11 Press selection keys to select AEXECUTEB, then press

ENTER for confirmation.

● To cancel the dubbing, press o then selection keys to select

ACANCELB and press ENTER to confirm.

12 Upon completing dubbing, the tape stops and ADUBBING

COMPLETEDB appears on the TV screen. Press ENTER to end.

Original Dubbing (From DVD To HDD)

It is possible to dub the original recordings on DVD discs to the HDD deck.

1 Load a disc you want to dub. 2 Press DUBBING to access the Dubbing Menu screen. 3 Press selection keys to select ADVD NHDDB, then press

ENTER.

4 Press selection keys to select indexes (small pictures) of

desired original recordings and/or play lists, then press MARK. After selecting all indexes you want to dub, press ENTER.

● You can select up to 8 original recordings and/or play lists.

5 Press selection keys to select AEXECUTEB, then press

ENTER to start dubbing.

NOTES:

● It is not possible to dub play lists on DVD discs.

● It is not possible to dub pre-recorded DVDVIDEO discs.

● It is not possible to dub Video CDs/SVCDs or Audio CDs.

● It is not possible to discontinue dubbing once it has been started.

Dubbing From DVD To DV

It is possible to perform dubbing from the DVD deck to the DV deck.

1 Load the disc you want to dub onto the DVD deck, and a Mini

DV cassette with the erase protection switch set to ARECB to the DV deck.

2 Press DUBBING to access the Dubbing Menu screen. 3 Press selection keys to select ADVDNDVB, then press ENTER. 4 Press selection keys to select indexes (small pictures) of

desired original recordings and/or play lists, then press MARK. After selecting all indexes you want to dub, press ENTER.

● You can select up to 8 original recordings and/or play lists.

5 Press selection keys to select ASELECT RECORDING

MODEB, then press ENTER. Press FG to select the desired option, then press ENTER. The confirmation screen appears.

6 Press selection keys to select ASELECT SOUND MODEB, then

press ENTER. Press selection keys to select the desired option, then press ENTER.

● Sound mode selection is not available when dubbing a

DVD-RW (Video mode) or DVD-R disc.

7 Press G to select ACONFIRMB, then press ENTER. The

confirmation screen appears.

8 Press DV so that the DV lamp lights up on the unit. 9 Press I to locate the point from where you want to start

dubbing, press o or W then press R and W simultaneously so that the DV deck enters the record pause mode.

10 Press DVD so that the DVD lamp lights up on the unit.

● The dubbing screen will appear.

11 Press selection keys to select AEXECUTEB, then press

ENTER to confirm.

● To cancel the dubbing, press o then selection keys to select

ACANCELB and press ENTER to confirm.

12 Upon completing dubbing, the tape stops and ADUBBING

COMPLETEDB appears on the TV screen. Press ENTER to end.

NOTES:

● It is not possible to dub play lists on DVD discs.

● It is not possible to dub Video CDs/SVCDs or Audio CDs.

● When dubbing is in progress, only o is functional.

Dubbing From DV To HDD (Dubbing An Entire Cassette)

It is possible to perform automatic dubbing of all the recorded programs of a cassette from the DV deck to the HDD deck using the AENTIREB dubbing. You cannot select the images to be dubbed; all recorded images on the DV cassette will be dubbed.

1 Load the Mini DV cassette you want to dub. Make sure its erase

protection switch is set to ASAVEB.

● Set ADV AUDIO RECB to the appropriate mode. (A pg. 71)

2 Press DUBBING to access the Dubbing Menu screen. 3 Press selection keys to select ADVNHDDB, then press

ENTER.

4 Select AENTIREB, then press ENTER. 5 Press selection keys to select ASELECT RECORDING

MODEB, then press ENTER. Press selection keys to select the desired option, then press ENTER.

6 Press selection keys to select ASELECT SOUND MODEB, then

press ENTER. Press selection keys to select the desired option, then press ENTER.

7 Press G to select ACONFIRMB, then press ENTER. The

confirmation screen appears.

8 Press selection keys to select AEXECUTEB, then press

ENTER for confirmation.

● Once dubbing starts, it will continue dubbing until the end of the

tape is reached.

● To cancel the dubbing, press o then selection keys to select

ACANCELB and press ENTER to confirm.

● If the tape is not rewind, the unit will start dubbing after

automatically rewinding the tape to the beginning.

9 Upon completing dubbing, the tape stops and ADUBBING

COMPLETEDB appears on the TV screen. Press ENTER to end.

● The tape will automatically be rewound.

NOTES:

● ASUPERIMPOSEB is automatically set to AOFFB. It will return to

AAUTOB after dubbing is completed.

● When there are blanks on the tape of more than 2 seconds, the

HDD deck will enter into pause mode while playback on DV deck continues. This also applies to portions of the DV tape that are damaged or unreadable. The last image is displayed on the TV screen. Dubbing will resume once recorded portion is detected. If the blank portion continues until the end of the tape, ADUBBING COMPLETEDB appears on the TV screen when the tape end is reached and the tape rewinds automatically.

● Dubbing copyright guarded tape is not possible.

● When dubbing is in progress, only o is functional.

Dubbing From DV To DVD (Dubbing An Entire Cassette)

It is possible to perform automatic dubbing of all the recorded programs of a cassette from the DV deck to the DVD deck using the AENTIREB dubbing. You cannot select the images to be dubbed; all recorded images on the DV cassette will be dubbed.

1 Load the Mini DV cassette you want to dub. Make sure its erase

protection switch is set to ASAVEB.

● Set ADV AUDIO RECB to the appropriate mode. (A pg. 71)

2 Press DUBBING to access the Dubbing Menu screen. 3 Press selection keys to select ADVNDV DB, then press ENTER. 4 Select AENTIREB, then press ENTER. 5 Press selection keys to select ASELECT RECORDING

MODEB, then press ENTER. Press selection keys to select the desired option, then press ENTER.

6 Press selection keys to select ASELECT SOUND MODEB, then

press ENTER. Press selection keys to select the desired option, then press ENTER.

7 Press G to select ACONFIRMB, then press ENTER. The

confirmation screen appears.

EDITING

EN 59

8 Press selection keys to select AEXECUTEB, then press

ENTER for confirmation.

● Once dubbing starts, it will continue dubbing until the end of the

tape is reached.

● To cancel the dubbing, press o then selection keys to select

ACANCELB and press ENTER to confirm.

● If the tape is not rewind, the unit will start dubbing after

automatically rewinding the tape to the beginning.

9 Upon completing dubbing, the tape stops and ADUBBING

COMPLETEDB appears on the TV screen. Press ENTER to end.

● The tape will automatically be rewound.

NOTES:

● ASUPERIMPOSEB is automatically set to AOFFB. It will return to

AAUTOB after dubbing is completed.

● The program information at the DV deck will not be dubbed.

● When there are blanks on the tape of more than 2 seconds, the

DVD deck will enter into pause mode while playback on DV deck continues. This also applies to portions of the DV tape that are damaged or unreadable. The last image is displayed on the TV screen. Dubbing will resume once recorded portion is detected. If the blank portion continues until the end of the tape, ADUBBING COMPLETEDB appears on the TV screen when the tape end is reached and the tape rewinds automatically.

● Dubbing copyright guarded tape is not possible.

● When dubbing is in progress, only o is functional.

About Disc Remaining Display

When dubbing from HDD to DVD, the unit displays the time information for dubbing by bar meter. By comparing the disc remaining time and the necessary time for dubbing of the selected items, it is possible to check if the dubbing can be performed completely or not.

When performing the High Speed Dubbing

Capacity of a disc Remaining capacity

21%

Dark green: Length of already recorded item Light green: Length of selected item Yellow: Length of the item now being selected by arrow Red: Excess over the capacity

When performing the Just Dubbing

TOTAL 105MIN

● The unit displays the status on the assumption that the selected

items are dubbed in the lowest transfer rate.

● The total time of a loaded disc is displayed on the right of the bar

meter.

When performing the Manual Dubbing

MAX FR240

● The unit displays the status on the assumption that the selected

items are dubbed in the lowest transfer rate.

● The available highest transfer rate is displayed on the right of the

bar meter.

60 EN

L–R

SOUND1

0:00 1:00 2:00

GR-DV3500

GR-DV3500DV

HDD

00:00: 00. 00

12bit

JVC

00:00: 00. 00

FR360

DV DV

1 2

A B C

EDITING

DV Dubbing (HDD & DVD Deck Only)

You can dub programs from a camcorder or DV equipment connected to the unit with a DV cable. The unit’s remote control allows you the limited control of the connected camcorder or DV equipment functions during dubbing.

NOTES:

● When connecting the unit to a device equipped with a DV input

connector, be sure to use the optional DV cable (VC-VDV 204U).

● When you connect a PC to the [DV IN] connector, we do not

assure the normal operation of this unit.

Your unit

To [DV IN]

Camcorder

DV equipment

DV cable

(VC-VDV 204U)

(not supplied)

DV connector

The following on-screen display for DV dubbing appears when ON SCREEN is pressed while the channel has been set to ADVB.

A Remote control switch

To switch between the devices operable by the remote control unit. The unit is operable when the remote icon ( ) displayed faces to the left, while the DV device is operable when the remote icon is facing to the right.

B Auto capture button

Select to start or pause the dubbing. If ENTER is pressed when the DV device is in the pause condition, preroll editing* where it is possible to dub with a start time that is highly accurate will be activated. When the DV device cannot be operated from the unit (such as in camera mode), proceed with normal recording (A pg. 34, 37).

●

Do not start dubbing at the portion with no time code (A––:––:––B).

* Preroll editing refers to the playback after the DV tape is slightly rewind.

(For DV devices that do not support the –1x speed, the rewinding time may be longer.)

C Sound monitor switch

For selecting the desired sound format for dubbing.

1 Connect a camcorder or DV equipment to the [DV IN] connector

on the unit’s front panel.

2 Press DV/HDD/DVD SELECT on the unit repeatedly; or press

HDD or DVD on the remote control to select the recording deck.

● When dubbing to a DVD disc, load a recordable disc on this

unit.

3 Press CH +/– to set the channel to ADVB. 4 Press ON SCREEN.

● The on-screen display for DV dubbing appears.

5 Press selection keys to select , then press ENTER

to display the remote icon (facing to the right) for the DV equipment.

6 Press REC MODE repeatedly to set the recording mode. For

DV deck, press REC MODE on the remote control to set the recording mode.

7 Locate the point from where you want to start dubbing, then

stop or pause playback by pressing the following buttons on the remote control: I, N, O, o, W.

● To play back in slow speed (1/10 of the normal speed), press W

to pause playback, then press O or N.

● To play back frame-by-frame, press W to pause playback, then

press W repeatedly. Each press of W advances a frame.

● To change the playback direction, press O or N.

8 Press selection keys to select , then press ENTER

repeatedly until the desired sound track appears on the TV screen.

SOUND1:

Select this to record the original stereo sound played back on the connected DV equipment.

SOUND2:

Select this to record the dubbed stereo sound played back on the connected DV equipment.

MIX:

Select this to record the sound of both ASOUND1B and ASOUND2B.

● Note that this selection is not available when the source

program is recorded in 16BIT (48 kHz) mode.

9 Press selection keys to select , then press

ENTER. The dubbing starts.

● Playback on the external DV equipment and recording on the

unit should start simultaneously.

● To pause dubbing, press selection keys to select ,

then press ENTER. Both the unit and the external DV equipment pause dubbing. Pressing W on the unit also works the same way.

10 Press selection keys to select , then press

ENTER. Then press o. The DV equipment stops.

11 Press selection keys to select , then press

ENTER.

12 Press o twice on the remote control to stop dubbing.

● Both the unit and the external DV equipment stop dubbing.

NOTES:

● Dubbing copyright guarded programs is not possible.

● Original DV information such as the recording date and time are

not recorded.

● The superimposed indication during the operation or dubbing is

not recorded.

● If the dubbing is paused while the channel is set to ADVB, you

cannot switch channels.

When you dub from DV equipment other than a camcorder

A Perform step 1 to 4. B Locate the point from where you want to start dubbing,

then stop on the DV equipment.

● If you pause the DV equipment in this step, a few

second’s still picture will be recorded at the beginning of the recorded program.

Set the input mode to ADV I NPUTB on the DV equipment.

● If you select an input mode other than ADV INPUTB,

unwanted pictures may be recorded at the beginning of the recorded program.

D Perform step 9 to 12.

EDITING

EN 61

To skip unwanted part of the source picture

Press ENTER to stop both equipment, then press selection keys to select . Locate the point where you want to restart dubbing by pressing I, N, or O, then press o. Press selection keys to select , then press ENTER to restart dubbing.

62 EN

EDITING

Edit From A Camcorder

You can use a camcorder as the source player and your unit as the recording deck. If your camcorder has a DV IN/OUT connector, you can use the camcorder as the recording deck and your unit (DV deck only) as the source player.

A If the camcorder has no S-VIDEO output connector:

To [VIDEO/AUDIO ((MONO) L/R)] input

Audio/video cable (not supplied)

AUDIO/VIDEO OUT

Player

B If the camcorder has an S-VIDEO output connector:

To [S-VIDEO]

input

S-video cable (not supplied)

To [AUDIO] input

S-VIDEO OUTPUT

AUDIO OUTPUT

Player

Recorder

Audio cable (not supplied)

Slide the TV/CABLE/DBS/DVD switch to DVD.

●

1 Make connections.

A If the camcorder has no S-VIDEO output connector:

^ connect the camcorder’s AUDIO/VIDEO OUT connectors to

the unit’s [VIDEO/AUDIO ((MONO) L/R)] input connectors on the front panel.

● When using a monaural camcorder, connect its AUDIO OUT

connector to the [AUDIO-L] input connector on your unit.

B If the camcorder has an S-VIDEO output connector:

^ connect the camcorder’s AUDIO OUT and S-VIDEO OUT

connectors to the unit’s [AUDIO] and [S-VIDEO] input connectors on the front panel.

C If the camcorder has a DV IN/OUT connector:

^ connect the camcorder’s DV IN/OUT connector to the unit’s

[DV IN/OUT] connector.

● When using your unit as the source player, refer to the

camcorder’s instruction manual for the recording procedure.

2 Press DV/HDD/DVD SELECT on the unit repeatedly to select

the recording deck.

3 Press CH +/– to select AF-1B or ADVB.

● Set AFRONT AUX F-1B to AVIDEOB for the [VIDEO] input

connector, or AS-VIDEOB for the [S-VIDEO] input connector, depending on the connector being used. (A pg. 72)

4 Press REC MODE repeatedly to set the recording mode. For

DV deck, press REC MODE on the remote control to set the recording mode.

5 Start playback on the camcorder slightly before the actual point

from where you wish to start dubbing.

6 Press R on the unit to start recording. Or while holding R, press

I on the remote control. The dubbing starts.

7 Press o on the unit, then stop playback on the camcorder.

NOTES:

● All necessary cables can be obtained from your dealer.

● Refer to the camcorder’s instruction manual for operating

procedure.

● The quality of dubbed picture becomes poorer than that of the

original.

● When you are editing through the [DV IN/OUT] connector, the

unit will stop if the player begins playing a blank portion of tape or the signal is interrupted.

● When connecting the unit to a device equipped with a DV input

connector, be sure to use the optional DV cable (VC-VDV 204U).

● To edit through the [DV IN/OUT] connector using the HDD or

DVD deck, refer to ADV Dubbing (HDD & DVD Deck Only)B (A pg. 60).

C If the camcorder has a DV IN/OUT connector:

Recorder/Player

To [DV IN]

(VC-VDV 204U)

(not supplied)

DV connector

Player/Recorder

DV cable

Edit To Or From Another Recorder

You can use your unit as the source player or as the recording deck.

NOTES:

● When using another recorder as the recording deck, refer to its

instruction manual.

● It is not possible to dub copy-protected contents. An error

message will appear on the TV screen.

A When using your unit as the source player

Player

Another recorder

Your unit

●

Slide the TV/CABLE/DBS/DVD switch to DVD.

EDITING

EN 63

1 Make connections.

A When using your unit as the source player:

^ connect its [S-VIDEO/VIDEO/AUDIO OUTPUT] connectors

to the input connectors on another recorder.

B When using your unit as the recording deck:

^ connect its [S-VIDEO/VIDEO/AUDIO INPUT] connectors on

the front or rear panel to the output connectors on another recorder.

● When connecting to another recorder with S-video connector,

set AREAR AUX L-1B or AFRONT AUX F-1B to AS-VIDEOB.

2 Press CH +/– to select the external input.

● Select AF-1B when the source player is connected to the unit’s

[VIDEO/AUDIO] or [S-VIDEO/AUDIO] input connectors on the front panel, and select AL-1B when it is connected to the unit’s [VIDEO/AUDIO] or [S-VIDEO/AUDIO] input connectors on the rear panel.

3 Press REC MODE repeatedly to set the recording mode. For

DV deck, press REC MODE on the remote control to set the recording mode.

4 Engage the Play mode on the source player. 5 Engage the Record mode on the recording deck. 6 Stop recording on the recording deck, then stop playback on the

source player.

NOTES:

● All necessary cables can be obtained from your dealer.

● When you use this unit as the source player for editing, be sure to

set ASUPERIMPOSEB to AOFFB before starting. (A pg. 72)

Recorder

B When using your unit as the recording deck

Player

Another recorder

Recorder

Your unit

64 EN

EDITING

Digital Audio Dubbing

You can dub selected audio from a DVD or Audio CD disc to a digital audio device. However, it is not possible to dub copy-protected discs.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

Example: Dubbing to an MD

Recorder

Digital audio device

(MD deck, etc.)

1 Connect the unit and a digital audio device using either an

optional optical cable or an optional coaxial cable.

2 Place a disc on the unit and load an MD on the connected

digital audio device.

3 Select the audio to be dubbed. 4 Start playback slightly before the actual point from where you

wish to start dubbing.

5 Press W to pause playback. 6 Select the input mode on the connected digital audio device. 7 Press I to start playback on the unit. 8 Start recording on the digital audio device. 9 Stop recording on the digital audio device. Then press o to stop

playback on the unit.

NOTE:

There may be a discrepancy of several seconds between where you intend editing to start, and where it actually starts.

Player

Coaxial cable (not supplied)

To [DIGITAL AUDIO

OUT (COAXIAL)]

Note for connection:

Remove the protection cap from the optical cable.

Optical cable (not supplied)

To [DIGITAL AUDIO OUT (OPTICAL)]

Rear of unit

Audio Dubbing (DV Deck Only)

This function allows you to record new audio, without erasing the original audio, on a DV tape that was recorded with ADV AUDIO RECB set to A12BITB (A pg. 71).

ATTENTION:

You cannot perform Audio Dubbing on a tape that was recorded with ADV AUDIO RECB set to A16BITB (A pg. 71), on a tape that was recorded at the ALPB speed, or on a blank tape.

Your unit

To [AUDIO]

input

CH +/–

Audio cable (not supplied)

AUDIO OUT

CD player, etc.

Mixer output

Recorder

A.DUB

Audio mixer

Slide the TV/CABLE/DBS/DVD switch to DVD.

●

EDITING

EN 65

1 Connect an audio device to the unit’s [AUDIO] input connectors

on the front panel.

● When using a monaural audio device, connect its AUDIO OUT

connector to the [AUDIO-L] input connector on your unit.

2 Load a Mini DV cassette with the erase protection switch set to

ARECB.

3 Press DV/HDD/DVD SELECT on the unit repeatedly or DV on

the remote control so that the DV lamp lights up on the unit.

4 Press CH +/– to select AF-1B. 5 Start playback slightly before the actual point from where you

wish to start dubbing.

6 Press W to pause playback. 7 Press A.DUB to engage the audio dubbing mode.

● Your unit enters the Audio Dubbing Pause mode.

● To perform Audio Dubbing with audio mixing, press AUDI O to

select AL+RB at this point. When using the DV deck as the recording deck, also make sure that AAUDIO MODEB is set to ASOUND1B (A pg. 71).

* Audio Dubbing with audio mixing is not possible if you are using a

monaural audio component, or if you don’t have an audio mixer.

8 Engage the audio device’s playback, then press I to start the

tape in the unit. Audio dubbing starts at this point.

● To stop dubbing temporarily, press W. Press I to resume

dubbing.

9 Press o on the unit, then stop playback on the audio device to

end the audio dubbing.

NOTES:

● Once the Audio Dubbing starts, you cannot use the other deck.

● When monitoring the audio dubbed sound on the DV deck, set

AAUDIO MODEB to ASOUND2B (A pg. 71).

● When playing back an audio dubbed Mini DV tape on the DV

deck, set AAUDIO MODEB to ASOUND2B (A pg. 71).

● Audio dubbing is not possible using the [DV IN/OUT] connector.

● Audio dubbing is not possible on a blank portion of the tape.

Your unit

[AUDIO]

input

Original sound

[AUDIO OUTPUT]

CH +/–

Recorder

A.DUB

66 EN

EDITING

Insert Editing (DV Deck Only)

Insert Editing replaces the pictures with new ones, while the audio soundtrack remains unchanged. For Insert Editing, use your unit as the recording deck.

ATTENTION:

Insert Editing is not possible with a Mini DV cassette recorded in LP mode.

A If the player has no S-VIDEO output connector:

Your unit

Player

CH +/–

To [VIDEO/AUDIO ((MONO) L/R)] input

Audio/video cable (not supplied)

AUDIO/VIDEO OUT

Another recorder

INSERT

B If the player has an S-VIDEO output connector:

Your unit

CH +/–

Recorder

●

Slide the TV/CABLE/DBS/DVD switch to DVD.

1 Make connections.

A If the player has no S-VIDEO output connector:

^ connect the player’s AUDIO/VIDEO OUT connectors to your

unit’s [VIDEO/AUDIO ((MONO) L/R)] input connectors on the front panel.

B If the player has an S-VIDEO output connector:

^ connect the player’s AUDIO OUT and S-VIDEO OUT

connectors to your unit’s [AUDIO] and [S-VIDEO] input connectors on the front panel.

2 Load a Mini DV cassette with the erase protection switch set to

ARECB.

3 Press DV/HDD/DVD SELECT on the unit repeatedly or DV on

the remote so that the DV lamp lights up on the unit.

4 Press CH +/– to select AF-1B. 5 Press S, T and W to determine the edit-in point (the

beginning of the segment to be replaced).

● Be sure to engage the Still mode at the edit-in point.

6 Press INSERT to engage the insert editing mode.

● Your unit enters the Insert Pause mode.

● The TV screen changes from the still picture to the input source

you are going to record.

7 Load the source cassette and play back the segment that is to

be inserted. When you reach the start of the section of the source tape that you wish to insert, press I to start the tape in your unit. Insert editing begins at this point.

8 Press o to stop recording on the DV deck to end insert editing.

NOTES:

● Once the Insert Editing starts, you cannot use the other deck.

● All necessary cables can be obtained from your dealer.

● Insert Editing cannot be performed on a Mini DV cassette that

has had its erase protection switch set to ASAVEB.

● When Insert Editing is performed on a tape that has been

recorded on another video recorder, the inserted portion may appear distorted.

● A small portion of the recording which precedes an insert edit

may become erased.

● Insert Editing is not possible using the [DV IN/OUT] connector.

● Insert Editing is not possible on a blank portion of the tape.

To [S-VIDEO]

input

S-video cable

(not supplied)

S-VIDEO

OUT

Player

To [AUDIO] input

Audio cable (not supplied)

AUDIO OUT

Another recorder

INSERT

REMOTE CONTROL

EN 67

Remote Control Functions

Remote Control 1/2/3/4 Code Switching

The remote control is capable of controlling four JVC video units independently. Each of the units can respond to one of the four codes (1, 2, 3 or 4). The remote control is preset to send code 3 signals because your unit is initially set to respond to code 3 signals. You can easily modify your unit to respond to code 1, 2 or 4 signals.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

CABLE/DBS

1 – 4

ENTER

SET UP

● Keep pressing SET UP down during step 1.

1 Press the number key A1B for 1, A2B for 2, A3B for 3 or A4B for 4 to

change the remote control code, then press ENTER.

2 Press A on the unit to turn off the unit. 3 Press I on the unit for over 5 seconds while the unit is turned

off. The current code appears on the front display panel.

4 Press o on the remote control to change the unit’s code. The

new code blinks on the front display panel for approximately 5 seconds, and is applied to the unit.

NOTE:

When APOWER SAVEB is set to AONB (A pg. 72), it is not possible to change the remote code.

DVDTV

CABLE/DBS

TV / VIDEO

0 – 9

TV MUTING

TV VOL +/–

CH +/–

ENTER

SET UP

DVDTV

TV Multi-Brand Remote Control

Your remote control can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer’s TVs can also be controlled.

● Turn off the TV using its remote control.

● Slide the TV/CABLE/DBS/DVD switch to TV.

IMPORTANT:

Although the provided remote control unit is compatible with JVC televisions, as well as many other models, it may not work with your TV, or in some instances, may have limited function capability.

● Keep pressing SET UP down during step 1.

1 Enter your TV’s brand code using the number keys, then press

ENTER.

2 Press A on the unit’s remote control to turn on the TV and try

operations (A step 3).

● Once you have set the remote control to operate the TV, you do

not have to repeat this step until you replace your remote control’s batteries.

● Some brands of TVs have more than one code. If the TV does

not function with one code, try entering another.

3 Press the corresponding buttons to operate the TV: A,

TV/VIDEO, CH +/–, TV VOL +/–, TV MUTING, number keys.

● For some brands of TVs, you must press ENTER after having

pressed the number keys.

68 EN

REMOTE CONTROL

BRAND NAME CODE

JVC HITACHI MAGNAVOX MITSUBISHI PA NA S O NI C RCA SHARP SONY SAMSUNG SANYO SEARS TOSHIBA ZENITH

01, 03 10 02 03 04, 11 05 06 07 12 13 13 08 09

Cable Box Or DBS Receiver Multi-Brand Remote Control

Your remote control can operate the basic functions of your cable box or DBS (Direct Broadcast Satellite) receiver set. In addition to JVC cable boxes or DBS receivers, other manufacturer’s cable boxes or DBS receivers can also be controlled.

● Slide the TV/CABLE/DBS/DVD switch to CABLE/DBS.

● Keep pressing SET UP down during step 1.

1 Enter your cable box or DBS receiver’s brand code using the

number keys, then press ENTER.

2 Press A on the unit’s remote control to turn on the cable box

or DBS receiver and try operations (墌 step 3).

● Once you have set the remote control to operate the cable box

or DBS receiver, you do not have to repeat this step until you replace your remote control’s batteries.

● Some brands of cable box or DBS receiver have more than one

code. If the cable box or DBS receiver does not function with one code, try entering another.

3 Press the corresponding buttons to operate the cable box or

DBS receiver: A, CH +/–, number keys.

● For some brands of cable box, you must press ENTER after

having pressed the number keys.

● The number keys may not function with some cable boxes.

IMPORTANT:

It may not work with your cable box, or in some instances, may have limited function capability.

NOTES:

● It’s not possible to operate a cable box or DBS receiver that is not

equipped with a receiving window.

● It’s not possible to set the remote control for both your cable box

and a DBS receiver at the same time. You can only set the remote control to operate one of these units at a time.

CABLE BOX BRAND CODE

ARCHER CABLETENNA CABLEVIEW CITIZEN CURTIS DIAMOND GC BRAND GEMINI GENERAL INSTRUMENTS HAMLIN JASCO JERROLD NOVAVISION OAK PA N AS O N I C PULSER RCA REGAL REMBRANDT SAMSUNG SCIENTIFIC ATLANTA SIGMA SL MARX SPRUCER STARGATE TELEVIEW TOCOM UNIKA UNIVERSAL VIDEOWAY ZENITH

DBS RECEIVER BRAND CODE

JVC (DISH Network) ECHOSTAR (DISH Network) SONY (DSS) RCA (DSS)

01, 05, 17 01, 17 15, 16, 17, 21, 25 15, 16, 17, 21, 25 02 01, 17 15, 16, 17, 21, 25 15 01, 04, 06, 11, 12, 15, 28 10, 18, 23 15 01, 04, 06, 11, 12, 15, 28 02 07 13, 14 15, 16, 17, 21, 25 13, 14 10, 18, 23 01, 16, 17 05, 16, 24 02 07 05, 16, 17, 24, 25 13, 14 05, 15, 16, 17, 21, 24, 25 05, 16, 24 01, 04, 16 01, 17 16, 17, 25 03, 09, 22 03, 09, 22

51 51 41 40

Connecting To A Dolby Digital Decoder Or An Amplifier With Built-in DTS

These instructions enable you to connect your unit to a Dolby Digital Decoder or an amplifier with built-in DTS.

Dolby Digital Decoder or

amplifier with built-in DTS

To DIGITAL AUDIO input

SYSTEM CONNECTIONS

EN 69

1 Connect the unit and a Dolby Digital Decoder or an amplifier

with built-in DTS using either an optional optical cable or an optional coaxial cable.

NOTES:

● For Dolby Digital sound, set ADIGITAL AUDIO OUTB to ADOLBY

DIGITAL/PCMB. (A pg. 70)

● For DTS sound, set ADIGITAL AUDIO OUTB to ASTREAM/PCMB.

(A pg. 70)

CAUTIONS:

● This unit has a dynamic range of more than 110 dB with regards

to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them.

● Some speakers and televisions are specially shielded to prevent

television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the playback picture.

Coaxial cable (not supplied)

To [DIGITAL AUDIO

OUT (COAXIAL)]

Note for connection:

Remove the protection cap from the optical cable.

Optical cable (not supplied)

To [DIGITAL AUDIO OUT (OPTICAL)]

Rear of unit

70 EN

SUBSIDIARY SETTINGS

Mode Set

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

CABLE/DBS

HDD

ENTER

DVD

Selection Keys

FGDE

*The boldface settings below indicate the settings at your purchase.

AUDIO OUTPUT

8 DIGITAL AUDIO OUT ^ DOLBY DIGITAL/PCM / STREAM/

/ PCM ONLY

PCM

Set to the appropriate mode according to the type of the device connected to [DIGITAL AUDIO OUT] connector.

DOLBY DIGITAL/PCM:

DVDTV

Select this when you connect the digital input connector of a Dolby Digital Decoder or an amplifier with a built-in Dolby Digital Decoder.

STREAM/PCM:

Select this when you connect the digital input connector of an amplifier with a built-in DTS, Dolby Digital, or MPEG multichannel decoder.

PCM ONLY:

Select this when you connect the linear PCM digital input of other audio equipment (amplifier, MD or DAT deck, etc.).

NOTES:

● This setting also functions when HDD is active.

● If you watch or play back a title which contains multiple audio

languages, select APCM ONLYB in advance and choose main or sub audio with AUDIO.

SET UP

AUDIO

Various modes of this unit are categorized into menus nested in 2 levels shown in the following table. To change the settings of these modes, find the desired mode in the menu (for details on each menu, see pages 70 through 72), then follow the procedure below.

DVD VIDEO SET UP LANGUAGE SET (A pg. 20)

AUDIO OUTPUT (See right column) PARENTAL LOCK (A pg. 33) DISC PLAY SET UP (A pg. 71)

HDD/DVD/DV SET UP HDD SET UP (A pg. 71)

DVD SET UP (A pg. 71) DISC SET UP (A pg. 74, 75) DV SET UP (A pg. 71)

FUNCTION SET UP REC/PLAY SET UP (A pg. 71)

DISPLAY SET (A pg. 72) VIDEO IN/OUT (A pg. 23, 72)

INITIAL SET UP TUNER SET (A pg. 22)

CLOCK SET (A pg. 21)

● The procedure below shows how to set the desired option of the

A2ND AUDIO RECORDB mode as an example.

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press SET UP to access the Main Menu screen. 3 Press selection keys to select AFUNCTION SET UPB, then

press G.

4 Press selection keys to select

AREC/PLAY SET UPB, then press G.

5 Press selection keys to select

A2ND AUDIO RECORDB, then

DVD VIDEO SET UP

REC/PLAY SET UP

XP MODE REC AUDIO

2ND AUDIO RECORD

JUMP TIME

HDD/DVD/DV SET UP

DISPLAY SET

FUNCTION SET UP

VIDEO IN/OUT

DOLBY DIGITAL

OFF

15 MIN

INITIAL SET UP

press ENTER.

ENTER

6 Press selection keys to select

the desired option, then press

SET UP

EXIT

SELECT

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

ENTER.

7 Press SET UP to complete the setting.

8 ANALOG AUDIO OUT ^ STEREO / DOLBY SURROUND

Select the appropriate setting to accommodate the unit to the connected A/V equipment. This function takes effect when a DVD VIDEO disc is played back.

STEREO:

Select this when listening to conventional two-channel stereo audio with the unit’s [AUDIO OUTPUT] connectors connected to a stereo amplifier/receiver or TV set, or in case you want to record the audio from a DVD VIDEO disc to a Mini Disc, etc.

DOLBY SURROUND:

Select this when listening to multichannel surround audio with the unit’s [AUDIO OUTPUT] connectors connected to an amplifier/receiver with a built-in surround decoder or a surround decoder.

8 D. RANGE CONTROL ^ NORMAL / WIDE RANGE / TV MODE

The dynamic range (the difference between the loudest sound and the quietest one) can be compressed during playback of a program encoded in Dolby Digital format. This function takes effect when a DVD VIDEO disc recorded in Dolby Digital format is played back at low or middle volume.

NORMAL:

Normally select this setting to activate this function.

WIDE RANGE:

Select this to deactivate this function when you enjoy wide dynamic range program.

TV MODE:

Select this when you hear the sound through the TV’s speaker(s).

NOTES:

● This function has no effect on programs other than those

recorded in Dolby Digital format.

● This function does not work when Simulated Surround Effect is

activated. (A pg. 31)

● The effect of ANORMALB and AWIDE RANGEB may not be

different depending on discs.

8 OUTPUT LEVEL ^ STANDARD / LOW

You can lower the output level of analog audio to accommodate the unit to the connected A/V equipment.

STANDARD:

Normally select this setting.

LOW:

The output level of analog audio is lowered.

SUBSIDIARY SETTINGS

EN 71

DISC PLAY SET UP

8 RESUME ^ OFF / ON / DISC RESUME

When this function is set to AONB or ADISC RESUMEB, you can use the resume function. (A pg. 26)

OFF:

You cannot use the resume function.

ON:

You can start playback from the resume point of the placed disc.

DISC RESUME:

The unit retains a memory of the resume points of the last 30 discs played back, even though they have been ejected.

NOTE:

ADISC RESUMEB setting works on DVD VIDEO, VCD, SVCD and already finalized DVD-R/DVD-RW (video mode) discs. For other types of discs, the function under AONB setting will be applied even if ARESUMEB is set to ADISC RESUMEB.

HDD SET UP

8 LIVE MEMORY ^ OFF / 30 MIN / 1 HR / 3 HR

When this function is set to A30 MINB, A1 HRB or A3 HRB, you can apply the selected time length to ATemporary recording for Live Memory (HDD deck only)B (A pg. 45).

DVD SET UP

8 SAVE AS LIBRARY ^ OFF / ON

When this function is set to AONB, the recording information is automatically stored in the library. For details, refer to ANavigate Library InformationB (A pg. 55).

8 CONTINUOUS PLAY ^ OFF / ON

When this function is set to AONB, multiple titles on a disc are played back continuously one after another.

8 VIDEO MODE RECORDING ASPECT ^ PRIORITIZE 4:3 /

PRIORITIZE 16:9

This is the setting for the aspect ratio used when you dub titles to DVD discs in video mode. If the titles you want to dub are recorded in both 16:9 and 4:3, you must select one aspect ratio.

PRIORITIZE 4:3:

If you select APRIORITIZE 4:3B, even a title recorded in 16:9 is dubbed in 4:3.

PRIORITIZE 16:9:

If you select APRIORITIZE 16:9B, even a title recorded in 4:3 is dubbed in 16:9.

8 MP3 & WMA / JPEG ^ MP3 & WMA / JPEG

You can select files to play back, when both MP3&WMA files and JPEG files are recorded on a disc.

MP3 & WMA:

Select this to play back MP3/WMA files.

JPEG:

Select this to play back JPEG files.

ATTENTION:

When SET UP is pressed while in the DV deck mode, the unit will switch to the previous deck mode (HDD or DVD). To proceed to DV deck after changing the settings in the ADV SET UPB menu, press DV/HDD/DVD SELECT on the unit repeatedly or DV on the remote control to select the DV deck.

DV SET UP

8 DV AUDIO REC ^12BIT / 16BIT

This is the setting for sound mode before recording on a Mini DV tape.

12BIT:

Enables Audio Dubbing later.

16BIT:

Audio Dubbing is not possible but the recorded sound quality is higher than A12BITB

8 AUDIO MODE ^ SOUND1 / SOUND2 / MIX

You can select the desired sound mode when playing back an audio dubbed Mini DV tape.

SOUND1:

Original recorded sound.

SOUND2:

Audio dubbed sound.

MIX:

Original recorded sound and audio-dubbed sound.

NOTES:

● When AAUDIO MODEB is set to AMIXB, both the main and sub

audio will be audible for bilingual tapes.

● To select only the main audio or only the sub audio of bilingual

tapes, set AAUDIO MODEB to ASOUND1B.

REC/PLAY SET UP

8 XP MODE REC AUDIO ^ DOLBY DIGITAL / LINEAR PCM

You can select the audio format when you record a title in XP mode. When this function is set to ALINEAR PCMB, you can obtain a high-quality audio sound.

DOLBY DIGITAL:

To record in Dolby Digital format.

LINEAR PCM:

To record in Linear PCM format.

8 2ND AUDIO RECORD ^ OFF / ON

When this function is set to AONB;

If a SAP program is received, the SAP audio is recorded on L/R tracks. The main audio is not recorded. If a non-SAP program is received, the main audio is recorded on L/ R tracks. When this function is set to AOFFB, the SAP audio cannot be recorded.

NOTE:

When the channel is changed on the unit;

● The AMONOB indicator appears on the screen for about 5

seconds if the program is a monaural broadcast.

● The ASTEREOB indicator appears on the screen for about 5

seconds if the program is a stereo broadcast.

● Both ASTEREOB and ASAPB indicators appear when a stereo

program is accompanied by SAP sound.

● Both AMONOB and ASAPB indicators appear when the main audio

on the monaural broadcast is accompanied by SAP sound.

72 EN

SUBSIDIARY SETTINGS

8 JUMP TIME ^ 15 MIN / 30 MIN / 1 HR

You can locate a scene ahead of or behind the currently viewed one by jumping a selected time interval during playback (or Live Memory Playback). For details, refer to AJump SearchB (A pg. 26,

40).

DISPLAY SET

8 SUPERIMPOSE ^ AUTO / OFF

When this function is set to AAUTOB, various operational indicators appear on the TV screen. Messages appear in the selected language. (A pg. 20)

AUTO:

To superimpose operational indications for approximately five seconds just after the corresponding operation.

OFF:

To turn off superimposed indications.

NOTES:

● When you use this unit as the source player for editing, be sure to

set ASUPERIMPOSEB to AOFFB before starting. (A pg. 63)

● When you select AAUTOB, during playback, the operation mode

indicators may be disturbed depending on the type of disc being used.

8 BLUE BACK ^ OFF / ON

When this function is set to AONB, the TV screen becomes all blue when receiving a channel not in use.

NOTE:

When you want to receive an unstable channel with poor signals, set this function to AOFFB.

8 DIMMER ^ BRIGHT / DIMMED

You can change the brightness of the front display panel.

BRIGHT:

Normally select this.

DIMMED:

To dim the front display panel. (Blue lamp on the front display panel is turned off.)

8 REAR AUX L-1 ^ VIDEO / S-VIDEO

Select the appropriate mode depending on the connector (L-1) being used on the rear panel.

VIDEO:

To use the [VIDEO INPUT] connector on the rear panel.

S-VIDEO:

To use the [S-VIDEO INPUT] connector on the rear panel.

8 POWER SAVE ^ OFF / ON

When this function is set to AONB, you can reduce the power consumption while the unit is turned off.

NOTES:

● During Power Save mode ^

^ the front display panel will be turned off.

● Power Save does not work when ^

^ the unit is in the Timer mode.

● It takes some time for the unit to complete initialization after you

turn on the unit power, with AWAKE UPB blinking on the front display panel.

8 ON SCREEN LANGUAGE

This unit offers you the choice to view on-screen messages in 3 different languages. For details, refer to AOn-screen Language SetB (A pg. 20).

VIDEO IN/OUT

8 MONITOR TYPE ^ 4:3LB / 4:3PS / 16:9AUTO / 16:9FIX

You can select the monitor type depending on the TV used when you play back DVD VIDEO discs recorded for wide-screen TVs. For details, refer to AMonitor SetB (A pg. 23).

8 FRONT AUX F-1 ^ VIDEO / S-VIDEO

Select the appropriate mode depending on the connector (F-1) being used on the front panel.

VIDEO:

To use the [VIDEO] input connector on the front panel.

S-VIDEO:

To use the [S-VIDEO] input connector on the front panel.

SUBSIDIARY SETTINGS

EN 73

Changing VCR Plus+ Setting

The VCR Plus+ programming system assigns a VCR Plus+ guide channel to the TV channels and the cable channels. These guide channel numbers are also called the VCR Plus+ channel codes. Most TV listings have a section, usually a chart, indicating the guide channel numbers assigned to each station. To ensure that VCR Plus+ timer recording operates correctly, it is necessary to set the “VCR Plus+ Guide Channel” for each station. If you have moved to a different area or if a broadcasting station’s channel number has been changed, perform the following steps to set the correct guide channel number.

NOTES:

● In many instances, the VCR Plus+ guide channel numbers for

cable and broadcast TV stations DO NOT match the channel number on which it is received by your unit or cable box. Check your TV listing, or contact your cable supplier for details.

● Many TV stations can be viewed on cable. Check your TV listing,

or contact your cable supplier for details.

● Turn on the unit.

● Turn on the TV and select the video channel (or AV mode).

● Slide the TV/CABLE/DBS/DVD switch to DVD.

CABLE/DBS

DVDTV

HDD

DVD

Guide Channel Number Set

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press SET UP to access the Main Menu screen. 3 Press selection keys to select AINITIAL SET UPB, then press

4 Press selection keys to select

ATUNER SETB, then press G.

5 Press selection keys to select

AGUIDE CH SETB, then press

ENTER.

6 Press selection keys to select

AGUIDE CH SETB, then press

ENTER.

7 Press selection keys to select

the Guide Channel number for the desired station as shown in the TV listings. Then press ENTER.

● If you receive your channels

with a cable box and if you have properly set your Controller, ACABLE CHB appears in place of ADVD CHB.

8 Press selection keys to select ADVD CHB, then press ENTER.

Press selection keys to select the number of the unit’s channel position on which the Guide Channel Number’s broadcast is received by the unit or the DBS receiver. Then press ENTER.

● Repeat steps 6 – 8 as necessary.

9 Press SET UP to complete the setting.

DVD VIDEO SET UP

TUNER SET CLOCK SET

ENTER

SET UP

EXIT

SELECT

INITIAL SET UP > GUIDE CH SET

GUIDE CH

CABLE CH

ENTER

SET UP

EXIT

SELECT

HDD/DVD/DV SET

AUTO CH SET

GUIDE CH SET

FUNCTION SET UP

MANUAL CH SET

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

INITIAL SET UP

RETURN

ENTER

Selection Keys

FGDE

SET UP

Guide Channel Number

“Guide Channel (GUIDE CH) Number” refers to the assigned TV station numbers, according to broadcast area, for the VCR Plus+ timer recording. The Guide Channel Numbers can be found in most TV listings.

74 EN

SUBSIDIARY SETTINGS

Format A Disc (DVD Deck Only)

Some DVD-RAM/RW discs are unformatted. Format the disc when you use an unformatted disc or you want to delete all recordings and data on the disc.

ATTENTION:

● When a disc is formatted, all recordings and data are erased. It

is impossible to restore them.

● Never turn off the unit or disconnect the AC power cord while

ANOW FORMATTING...B is displayed on the TV screen.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Load a DVD-RAM/RW disc to format.

CABLE/DBS

DVDTV

HDD

ENTER

DVD

Selection Keys

FGDE

SET UP

Format A DVD-RAM Disc

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press SET UP to access the Main Menu screen. 3 Press selection keys to select AHDD/DVD/DV SET UPB, then

press G.

4 Press selection keys to select

ADISC SET UPB, then press G.

5 Press selection keys to select

AFORMATB, then press

ENTER. Press selection keys to select AOKB, then press ENTER.

6 Press selection keys to select

AEXECUTEB, then press

ENTER.

DVD VIDEO SET UP

HDD SET UP

SET UP

EXIT

HDD/DVD/DV SET UP

DVD SET UP DISC SET UP

FINALIZE

Video

ENTER

SELECT

FUNCTION SET UP

CANC. FINALIZ.

FORMAT

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

INITIAL SET UP

DV SET UP

Video

Format A DVD-RW Disc

1 Perform steps 1 to 4 of AFormat A DVD-RAM DiscB as above

before continuing.

2 Press selection keys to select AFORMATB, then press ENTER.

Press selection keys to choose AVR MODEB or AVIDEO MODEB, then press ENTER when ADISC WILL BE FORMATTEDB appears on the TV screen.

AVR MODEB:

To be chosen when you want to record, erase, or edit data on the disc repeatedly.

AVIDEO MODEB:

To be chosen when you want to erase all the data on the disc once played back to record new data, or play back the disc on other DVD players.

3 Press selection keys to select AEXECUTEB, then press

ENTER.

NOTES:

● It is impossible to format Version 1.0 DVD-RW discs in Video

mode.

● It is impossible to format DVD-R discs.

● All the titles on a disc will be deleted once the disc is formatted

even if they are protected titles. (A pg. 52)

SUBSIDIARY SETTINGS

EN 75

Finalize A Disc (DVD Deck Only)

Finalizing DVD-R/RW discs recorded on this unit makes it possible for the discs to be played back on other DVD players. DVD-RW discs are finalized in the mode that the discs were formatted, enabling playback on compatible DVD players. Title names input in the Library Database Navigation are registered as title names in the DVD menu. (A pg. 51)

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

● Load a DVD-R/RW disc to finalize.

CABLE/DBS

DVDTV

ENTER

Selection Keys

FGDE

SET UP

Finalize A DVD-R/RW Disc

1 Perform steps 1 to 4 of AFormat A DVD-RAM DiscB (A pg. 74)

before continuing.

2 Press selection keys to select AFINALIZEB, then press ENTER.

● For DVD-R/RW (Video mode) discs, the background selection

screen will appear. Press selection keys to select the desired background from a selection of 18 backgrounds, then press ENTER.

3 Press selection keys to select AOKB, then press ENTER. 4 Upon completing finalization, ACOMPLETEDB appears on the

TV screen. Press ENTER to end.

5 Press SET UP to return to the normal screen.

● Menu screen is cleared.

● Once a DVD-R/RW (Video mode) disc has been finalized, the

displays for original and play list do not appear. Only display for library appears.

● Once a DVD-RW (VR mode) disc has been finalized, it can be

played on DVD players compatible with VR mode.

Cancel The Finalization Of A DVD-RW Disc

1 Load a DVD-RW disc to cancel the disc finalization, and

perform steps 1 to 4 of AFormat A DVD-RAM DiscB (A pg. 74) before continuing.

2 Press selection keys to select ACANC. FINALIZ.B, then press

ENTER.

3 Press selection keys to select AEXECUTEB, then press

ENTER.

4 Upon completing cancellation of finalization, ACANCELLATION

COMPLETEDB appears on the TV screen. Press ENTER to end.

5 Press SET UP to return to the normal screen.

● When the disc finalization is canceled, the mode in which the

disc was formatted is restored, making the disc recordable. (A pg. 9, 74)

Before finalizing

● It is possible to record on a blank space.

● It is possible to enter title names. (A pg. 51)

● It is possible to delete titles. (A pg. 52)

● It is impossible to overwrite recorded areas of DVD-R discs.

● Available recording capacity does not increase even if a recorded

title is deleted from a DVD-R disc.

● It is impossible to record or edit DVD-R/RW discs recorded on

other devices even if they have not been finalized.

After finalizing (For DVD-R/RW (Video mode) discs)

● Video and audio that have been recorded by then are recorded in

conformity to the DVD Video standard, enabling you to play back the discs as DVD VIDEO discs.

● Although DVD-R/RW discs finalized on this unit become playable

on DVD players compatible with DVD-R/RW discs, some discs still may not play, for which JVC cannot take responsibility.

● Marked points marked before finalizing will be deleted, and titles

will be divided automatically into AchaptersB approximately every 5 minutes. (A pg. 27)

● Depending on the DVD players and DVD-R/RW discs used, and

on the conditions of recording, it may not be possible to play back the discs. In this case, play back the discs on this unit.

● Additional recordings become impossible.

76 EN

SUBSIDIARY SETTINGS

Scan Mode Set (HDD & DVD Deck Only)

If you connect the unit and TV with Component Video Connection (A pg. 18), you can select the scan mode from two modes: Interlaced scan mode which is used in the conventional TV system, and Progressive scan mode which enables reproduction of higher-quality images.

8 Interlaced scan

In the conventional video system, a picture is shown on the display monitor in two halves. The Interlaced scan system places lines of the second half of the picture in-between lines of the first half of the picture.

8 Progressive scan

Progressive scan displays all the horizontal lines of a picture at one time, as a single frame. This system can convert the interlaced video from DVD into progressive format for connection to a progressive display. It dramatically increases the vertical resolution.

ATTENTION:

Your TV needs to be compatible with Progressive.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/DBS/DVD switch to DVD.

CABLE/DBS

DVDTV

HDD

DVD

Tray Lock (DVD Deck Only)

You can lock the disc tray to prohibit the unwanted disc ejection by children.

● Turn off the unit.

To lock tray

While the unit is turned off, press and hold o, then press M on the unit. ALOCKB appears on the front display panel and the disc tray is locked.

To unlock tray

While the unit is turned off, press and hold o, then press M on the unit. AUNLOCKB appears on the front display panel.

Child Lock

You can disable the operations of this unit using the Child Lock function.

● Turn on the unit.

PROGRESSIVE SCAN

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press PROGRESSIVE SCAN for 3 or more seconds.

● Video output indicator (q) lights on the front display panel if

Progressive scan mode has been established. (A pg. 14)

● Each press of PROGRESSIVE SCAN for 3 or more seconds

switches the scan mode.

NOTES:

● Interlaced scan mode is the setting at your purchase.

● Interlaced scan mode might be suitable depending on video

material.

● Scan mode cannot be set while menu screen is displayed.

● When the Progressive scan mode is engaged, no video signal is

output from [S-VIDEO OUTPUT] connector and [VIDEO/AUDIO OUTPUT] connectors.

1 When the unit is turned on, press and hold DVD A on the

remote control for more than 10 seconds.

● The unit turns off and enters into Child Lock mode.

● When in Child Lock mode, ACLB will appear on the front display

panel indicating that Child Lock mode is engaged when an attempt was made to operate buttons on the unit or remote control.

2 Press and hold DVD A on the remote control for more than 10

seconds.

● Child Lock is released and the unit turns on.

NOTE:

Timer recording will be performed even if Child Lock is activated.

Before requesting service for a problem, use this chart and see if you can solve the trouble yourself. Small problems are often easily solved, and this can save you the trouble of sending your unit off for repair.

Initializing (DVD Deck Only)

Malfunction occurs on the unit.

] Press A to turn off the unit, press and hold A, then press o

for two seconds or more.

General

No power is supplied to the unit.

● The AC power plug is disconnected from the AC outlet.

] Connect the AC power plug to the AC outlet securely.

(A pg. 18)

The remote control does not work properly.

] Remove the batteries, wait for 5 minutes or more, then load the

butteries again.

● The setting of the remote control code is inappropriate.

] Set the same remote control code (1, 2, 3, or 4) on both the unit

and the remote control. (A pg. 67)

● The batteries are discharged.

] Replace the dead batteries with new ones.

Dubbing from the external equipment is not possible.

● The source (another video recorder, camcorder) has not been

properly connected.

] Confirm that the source is properly connected.

● All necessary power switches have not been turned on.

] Confirm that all units’ power switches are turned on.

● The setting of the input channel position is inappropriate.

] Select the input channel position (AF-1B or AL-1B) that

corresponds to the input terminal connected to the external equipment. (A pg. 63)

The on-screen display superimposed on the program played back/received on this unit is recorded when you dub the program to an external recording equipment.

] Set ASUPERIMPOSEB to AOFFB. (A pg. 72)

The unit does not operate.

● There are cases when the operation is prohibited on the disc.

● Lightning or static electricity may cause malfunction of the unit.

] Press A to turn the power off, then press the button again to

turn the power on.

The remote control of a JVC TV will not operate the unit.

● The setting of the remote control code is inappropriate.

] To operate the unit using a JVC TV remote control, set the

remote control code of the unit to A1B (Default: A3B). (A pg. 67)

TROUBLESHOOTING

EN 77

Playback (DVD Deck)

The DVD deck cannot be operated.

● The DVD deck is not selected.

] Press DV/HDD/DVD SELECT on the unit repeatedly or DVD on

the remote control so that the DVD lamp lights up on the unit.

Images do not appear on the TV screen.

● The TV receiver’s channel selector is not set to the AV mode.

] Set the TV to its AV mode.

● When interlace scanned program is played back, progressive

scan mode is selected.

] Press and hold PROGRESSIVE SCAN until q disappears

from the front display panel. (A pg. 76)

Playback does not start or stop immediately after playback is started by pressing I. On the front display panel, ANO DISCB appears.

● The disc is loaded upside down.

] Place the disc on the disc tray with the playback surface facing

down. (A pg. 10)

● A disc not being compatible with the unit is loaded.

] Load a playable disc on the unit. (A pg. 7)

● A dirty disc is loaded.

] Clean the disc. (A pg. 11)

● Defective disc is loaded.

] Replace the warped or scratched disc with a normal one.

Images are blurred or distorted when you start High-Speed Search.

] Images are blurred or distorted at the point where the playback

speed changes and this is not a malfunction of the unit.

Playback does not start.

] Playback does not start for approximately 30 seconds after

recording is stopped and this is not a malfunction of the unit.

Playback does not start when you select a title or a chapter.

● The Parental Lock is engaged and the disc is rated higher than

the set level.

] Release the Parental Lock temporarily or change the set level.

(A pg. 33)

Playback (HDD Deck)

The HDD deck cannot be operated.

● The HDD deck is not selected.

] Press DV/HDD/DVD SELECT on the unit repeatedly or HDD on

the remote so that the HDD lamp lights up on the unit.

78 EN

TROUBLESHOOTING

Playback (DV Deck)

The DV deck cannot be operated.

● The DV deck is not selected.

] Press DV/HDD/DVD SELECT on the unit repeatedly or DV on

the remote control so that the DV lamp lights up on the unit.

The tape will not rewind or fast-forward.

● The tape is already fully rewound or fast-forwarded.

] Check the cassette.

The playback picture does not appear while the tape is running.

● The TV is not set to the AV mode.

] Set the TV to the AV mode.

Noise appears during visual search.

● This is normal.

The playback picture is blurred or interrupted while TV broadcasts are clear or AUSE CLEANING CASSETTEB message appears on the screen.

● The video heads may be dirty.

] Use a dry cleaning cassette M-DV12CL, or consult your JVC

dealer.

Recording (DVD Deck)

The desired program cannot be recorded.

● The channel position does not correspond to that in the

receiving area.

] Set the correct channel position for the receiving broadcast.

(A pg. 22)

Recording cannot be made.

● No disc or a disc not being compatible with the unit is loaded.

] Load a recordable disc on the unit. (A pg. 7)

● The disc loaded is not formatted.

] Format the disc. (A pg. 74)

● A finalized DVD-R disc is loaded.

] Recording cannot be made on finalized discs. Load a

recordable disc on the unit.

● The disc is full or does not have enough space for the title to be

recorded.

] Clear unnecessary titles on the disc or load a blank disc.

(A pg. 52)

● The DVD-RAM disc loaded has had its protect tab slid to the

protect position.

] Release the protect tab. (A pg. 10)

Recording (HDD Deck)

TV broadcasts cannot be recorded.

● AL-1B or AF-1B has been selected as the input mode.

] Set to the desired channel.

Camcorder recording is not possible.

● The camcorder has not been properly connected.

] Confirm that the camcorder is properly connected.

● The input mode is not correct.

] Set the input mode to AF-1B. (A pg. 62)

Recording (DV Deck)

During recording, the tape does not run. The DV recording lamp lights up on the unit.

● The unit is in the Record Pause mode.

] Press I to resume recording.

Recording cannot be done.

● There is no cassette loaded, or the cassette loaded has had its

erase protection switch set to ASAVEB.

] Insert a Mini DV cassette, or set the erase protection switch set

to ARECB.

● An attempt has been made to record from this unit’s built-in

tuner.

] It is not possible to record from this unit’s built-in tuner to the DV

deck. Record to the HDD or a DVD disc. If you want to record on a DV tape, record by connecting the output of the external equipment such as a cable box to this unit’s external input ([L-1], etc.).

Camcorder recording is not possible.

● The camcorder has not been properly connected.

] Confirm that the camcorder is properly connected.

● The input mode is not correct.

] Set the input mode to AF-1B or ADV B.

The tape is automatically rewound, then the unit is shut off.

● The end of the tape was reached during recording.

] The program may not have been recorded in its entirety. Next

time make sure you have enough time on the tape to record the entire program.

Audio dubbing is not possible.

● ADV AUDIO RECB had been set to A16BITB at the original

recording.

] Set ADV AUDIO RECB to A12BITB at the original recording.

● The tape speed had been set to LP at the original recording.

] Set the tape speed to SP at the original recording.

Monitoring the audio dubbed sound is not possible during audio dubbing.

] This is normal. Monitor the sound using the connected devices.

TROUBLESHOOTING

EN 79

Timer Recording (HDD & DVD Deck)

Timer programming cannot be made.

● Date and time is not correct.

] Set date and time correctly. (A pg. 21)

● Timer recording is in progress.

] Timer programming can’t be performed while a timer recording

is in progress. Wait until it finishes.

Timer programming recording does not start.

● Date and time is not correct.

] Set date and time correctly. (A pg. 21)

VCR Plus+ Timer Programming cannot be made.

● Date and time set on the unit is not correct.

] Set date and time correctly. (A pg. 21)

● The channel position does not correspond to that in the

receiving area.

] Set the correct channel position for the receiving broadcast.

(A pg. 22)

The VCR Plus+ system does not timer record properly.

● The unit’s channel positions have been set incorrectly.

] Refer to AChanging VCR Plus+ SettingB (A pg. 73) and

reperform the procedure.

On the front display panel, A––:––B appears.

● Power failure occurred.

] Set date and time correctly. (A pg. 21)

APROGRAM FULLB appears on the TV screen during timer programming.

● 32 programs have already been timer programmed.

] Clear unnecessary programs on the unit, then try timer

programming again. (A pg. 49)

The disc space does not increase when recorded titles are cleared.

● The PC’s data recorded on a DVD-RAM drive cannot be cleared

on this unit.

] Format the disc. (When the disc is soiled, wipe the disc with a

soft dry cloth before formatting.) (A pg. 11, 74)

APPENDIX

EN 81

82 EN

APPENDIX

Country/Area Code List for Parental Lock

AD Andorra CK Cook Islands GN Guinea AE United Arab Emirates CL Chile GP Guadeloupe AF Afghanistan CM Cameroon GQ Equatorial Guinea AG Antigua and Barbuda CN China GR Greece AI Anguilla CO Colombia GS South Georgia and the South

AL Albania CR Costa Rica GT Guatemala AM Armenia CU Cuba GU Guam AN Netherlands Antilles CV Cape Verde GW Guinea-Bissau AO Angola CX Christmas Island GY Guyana AQ Antarctica CY Cyprus HK Hong Kong AR Argentina CZ Czech Republic HM Heard Island and McDonald

AS American Samoa DE Germany HN Honduras AT Austria DJ Djibouti HR Croatia AU Australia DK Denmark HT Haiti AW Aruba DM Dominica HU Hungary AZ Azerbaijan DO Dominican Republic ID Indonesia BA Bosnia and Herzegovina DZ Algeria IE Ireland BB Barbados EC Ecuador IL Israel BD Bangladesh EE Estonia IN India BE Belgium EG Egypt IO British Indian Ocean Territory BF Burkina Faso EH Western Sahara IQ Iraq BG Bulgaria ER Eritrea IR Iran (Islamic Republic of) BH Bahrain ES Spain IS Iceland BI Burundi ET Ethiopia IT Italy BJ Benin FI Finland JM Jamaica BM Bermuda FJ Fiji JO Jordan BN Brunei Darussalam FK Falkland Islands (Malvinas) JP Japan BO Bolivia FM Micronesia

(Federated States of) BR Brazil FO Faroe Islands KG Kyrgyzstan BS Bahamas FR France KH Cambodia BT Bhutan FX France, Metropolitan KI Kiribati BV Bouvet Island GA Gabon KM Comoros BW Botswana GB United Kingdom KN Saint Kitts and Nevis BY Belarus GD Grenada KP Korea, Democratic People’s

BZ Belize GE Georgia KR Korea, Republic of CA Canada GF French Guiana KW Kuwait CC Cocos (Keeling) Islands GH Ghana KY Cayman Islands CF Central African Republic GI Gibraltar KZ Kazakhstan CG Congo GL Greenland LA Lao People’s Democratic

CH Switzerland GM Gambia LB Lebanon CI Côte d’Ivoire

KE Kenya

Sandwich Islands

Islands

Republic of

Republic

APPENDIX

LC Saint Lucia NU Niue SZ Swaziland LI Liechtenstein NZ New Zealand TC Turks and Caicos Islands LK Sri Lanka OM Oman TD Chad LR Liberia PA Panama TF French Southern Territories LS Lesotho PE Peru TG Togo LT Lithuania PF French Polynesia TH Thailand LU Luxembourg PG Papua New Guinea TJ Tajikistan LV Latvia PH Philippines TK Tokelau LY Libyan Arab Jamahiriya PK Pakistan TM Turkmenistan MA Morocco PL Poland TN Tunisia MC Monaco PM Saint Pierre and Miquelon TO Tonga MD Moldova, Republic of PN Pitcairn TP East Timor MG Madagascar PR Puerto Rico TR Turkey MH Marshall Islands PT Portugal TT Trinidad and Tobago ML Mali PW Palau TV Tuvalu MM Myanmar PY Paraguay TW Taiwan MN Mongolia QA Qatar TZ Tanzania, United Republic of MO Macau RE Réunion UA Ukraine MP Northern Mariana Islands RO Romania UG Uganda MQ Martinique RU Russian Federation UM United States Minor Outlying

Islands MR Mauritania RW Rwanda US United States MS Montserrat SA Saudi Arabia UY Uruguay MT Malta SB Solomon Islands UZ Uzbekistan MU Mauritius SC Seychelles VA Vatican City State (Holy See) MV Maldives SD Sudan VC Saint Vincent and the

Grenadines MW Malawi SE Sweden VE Venezuela MX Mexico SG Singapore VG Virgin Islands (British) MY Malaysia SH Saint Helena VI Virgin Islands (U.S.) MZ Mozambique SI Slovenia VN Viet Nam NA Namibia SJ Svalbard and Jan Mayen VU Vanuatu NC New Caledonia SK Slovakia WF Wallis and Futuna Islands NE Niger SL Sierra Leone WS Samoa NF Norfolk Island SM San Marino YE Yemen NG Nigeria SN Senegal YT Mayotte NI Nicaragua SO Somalia YU Yugoslavia NL Netherlands SR Suriname ZA South Africa NO Norway ST Sao Tome and Principe ZM Zambia NP Nepal SV El Salvador ZR Zaire NR Nauru SY Syrian Arab Republic ZW Zimbabwe

EN 83

84 EN

SPECIFICATIONS

GENERAL

Power requirement

AC 120 VH, 60 Hz

Power consumption

Power on: 49 W Power off: 12 W

Temperature

Operating: 5°C to 35°C (41°F to 95°F) Storage: –20°C to 60°C (–4°F to 140°F)

Operating position

Horizontal only

Dimensions (WxHxD)

435 mm x 96 mm x 383 mm (17-1/10" x 3-4/5" x 15")

Weight

6.4 kg (14.1 lbs)

Input/Output

Video input: 0.5 - 2.0 Vp-p, 75 K (pin jack) Audio input:

–8 dB, 50 kK (pin jack)

Corresponding to mono (left) Audio output: –8 dB, 1 kK (pin jack) S-video input:

Y: 0.8 - 1.2 Vp-p, 75 K

C: 0.2 - 0.4 Vp-p, 75 K S-video output:

Y: 1.0 Vp-p, 75 K

C: 0.3 Vp-p, 75 K DV: 4-pin for DV IN/OUT Component video output:

Y: 1.0 Vp-p, 75 K

, PB/PR: 0.7 Vp-p, 75 K

B/CR

Corresponding to copy protection Digital audio output:

Optical, Coaxial

Corresponding to Dolby Digital and DTS Digital Surround

Bit stream

Selectable in digital audio output setting menu

VIDEO/AUDIO (DVD Deck)

Recording time

Maximum 8 hours (with 4.7 GB disc) (XP): Approx. 1 hour (SP): Approx. 2 hours (LP): Approx. 4 hours (EP): Approx. 6 hours (FR): Approx. 1 hour - 8 hours

Audio recording system

Dolby Digital (2 ch) Linear PCM (XP mode only)

Video recording compression system

MPEG2 (CBR/VBR)

VIDEO/AUDIO (HDD Deck)

Video recording compression system

MPEG2 (VBR)

Audio recording system

Dolby Digital (2 ch) Linear PCM (XP mode only)

Recording time

Maximum 473 hours (with 250 GB HDD) (XP): Approx. 53 hours (SP): Approx. 109 hours (LP): Approx. 218 hours (EP): Approx. 328 hours (FR): Approx. 473 hours

VIDEO/AUDIO (DV Deck)

Signal system

NTSC color signal and EIA monochrome signal, 525 lines/60 fields

Recording system

Digital Component Recording

Format

DV format (SD mode)

Cassette

Mini DV Cassette

Maximum recording time

(SP): 80 min. with M-DV80ME cassette (LP): 120 min. with M-DV80ME cassette

Audio recording system

PCM 48 kHz, 16 bit (2 ch)/ 32 kHz, 12 bit (4 ch)

Specifications shown are for SP mode unless otherwise specified.

TUNER/TIMER

Tuning system

Frequency synthesized tuner

Channel coverage

VHF: Channels 2 - 13 UHF: Channels 14 - 69 CATV:113 channels

Memory backup time

Approx. 60 minutes

ACCESSORIES

Provided accessories

RF cable, Audio/Video cable, Infrared remote control unit, AAAB battery x 2

E.& O.E. Design and specifications subject to change without notice.

ATTENTION:

This unit contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the unit off and unplug the AC power cord. Then plug it in again and turn the unit on. Take out the disc. After checking the disc, operate the unit as usual.

A-B Repeat Playback ................................................ 30

Accidental erasure prevention .................................... 41

Adjusting The Picture Quality ..................................... 31

Angle Selection ........................................................ 27

Audio Channel Selection ........................................... 28

Audio Language/Sound Selection ............................... 28

Auto Channel Set ..................................................... 22

Auto Daylight Saving Time ........................................ 21

Basic Playback .............................................. 24, 39, 41

Basic Recording ..................................................34, 37

Cancel And Change Programs ................................... 49

Check Programs ....................................................... 49

Child Lock ............................................................... 76

Country/Area Code List for Parental Lock .................... 82

Disc menu ............................................................... 25

Disc Remaining Time ...........................................35, 38

Disc Resume ........................................................... 71

Discs For Playback Only ............................................. 8

DVD menu ............................................................... 25

Elapsed Recording Time Indication .......................35, 38

File Structure Of Discs ................................................ 9

Free Rate Function ................................................... 36

Guide Channel Number ............................................. 73

Instant Timer Recording (ITR) ...............................35, 38

Interlaced scan ......................................................... 76

Jump Search .......................................................26, 40

Language Code List .................................................. 81

Letter Box ................................................................ 23

Live Memory ............................................................ 45

Manual Channel Set ................................................. 22

Manual Clock Set ..................................................... 21

Marking Positions To Play Back Again Later ...........27, 40

Menu/Audio/Subtitle Language Set ............................. 20

Next Function Memory .............................................. 42

LIST OF TERMS

EN 85

One Touch Replay ................................... 26, 40, 42, 45

On-screen Bar .......................................................... 29

On-screen Language Set ........................................... 20

Pan&Scan ................................................................ 23

Parental Lock ........................................................... 33

Play List ................................................................... 53

Playback Control (PBC) ............................................. 28

Program Playback .................................................... 32

Progressive scan ...................................................... 76

Random Playback ..................................................... 32

Recordable/Playable Discs .......................................... 7

Recording Medium And Format .................................... 9

Recording Mode ................................................. 34, 37

Region Number .......................................................... 8

Relief Recording ....................................................... 48

Repeat Playback ...................................................... 29

Resume Function ..................................................... 26

Resuming Playback .................................................. 45

RetroActive Recording .............................................. 45

Select The Switching Interval Of The Slide Show .........32

Semiauto Clock Set .................................................. 21

Setting The Progressive Mode ................................... 32

Simulated Surround Effect ......................................... 31

Simultaneous Recording and Playback ....................... 45

Skip Search ..................................................26, 39, 42

Slow Motion ..................................................25, 39, 42

Soundtrack Selection ................................................ 42

Still Picture/Frame-By-Frame Playback ............25, 39, 42

Subtitle Selection ...................................................... 28

Temporary Recording ................................................ 45

Time Code ............................................................... 42

Time Search ............................................................ 31

Top menu ................................................................ 25

Tray Lock ................................................................. 76

Unplayable Discs ........................................................ 8

Usable cassettes ...................................................... 41

Variable Speed Search ...................................25, 39, 42

Weekly/Daily Recording ............................................ 47

86 EN

WARRANTY (Only in U.S.A.)

MEMO

EN 87

FOR SERVICING (Only in U.S.A.)

DR-DX5SU

Printed in China

0905KTH-SW-BJ

JVC DR-DX5SU User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

SAFETY FIRST

CONTENTS

About Discs

DISC INFORMATION

INDEX

Front View

Rear View

Front Display Panel

Remote Control

On-Screen Display (HDD & DVD deck)

On-Screen Display (DV Dubbing)

On-Screen Display (DV deck)

INSTALLING YOUR NEW UNIT

Basic Connections

Plug & Play Set

INITIAL SETTINGS

Language

Clock Set

Tuner Set

Monitor Set

BASIC OPERATIONS ON DVD DECK

Basic Playback

Playback Features

Using The On-screen Bar

Parental Lock

Basic Recording

Recording Features

Basic Recording

BASIC OPERATIONS ON HDD DECK

Recording Features

Basic Playback

Playback Features

Basic Playback

BASIC OPERATIONS ON DV DECK

Playback Features

LIVE MEMORY PLAYBACK ON HDD/DVD DECK

Live Memory Playback

TIMER RECORDING ON HDD/DVD DECK

VCR Plus+ Timer Programming

Manual Timer Programming

NAVIGATION ON HDD/DVD DECK

Library Database Navigation

Edit Original Information

Edit Play List Information

Navigate Library Information

Playback With MP3/WMA/JPEG Navigation

Dubbing

EDITING

DV Dubbing (HDD & DVD Deck Only)

Edit From A Camcorder

Edit To Or From Another Recorder

Digital Audio Dubbing

Audio Dubbing (DV Deck Only)

Insert Editing (DV Deck Only)

REMOTE CONTROL

Remote Control Functions

Connecting To A Dolby Digital Decoder Or An Amplifier With Built-in DTS

SYSTEM CONNECTIONS

SUBSIDIARY SETTINGS

Mode Set

Changing VCR Plus+ Setting

Format A Disc (DVD Deck Only)

Finalize A Disc (DVD Deck Only)

Scan Mode Set (HDD & DVD Deck Only)

Tray Lock (DVD Deck Only)

Child Lock

TROUBLESHOOTING

APPENDIX

SPECIFICATIONS

LIST OF TERMS

WARRANTY (Only in U.S.A.)

FOR SERVICING (Only in U.S.A.)