JVC DLA-VS2100U, DLA-VS2100NL User Manual
Operation
Others
Preparation
Getting Started
Maintenance
0211TTH-AO-AO
© 2011 Victor Company of Japan, Limited
DLA-F110
D-ILA PROJECTOR
PROYECTOR D-ILA
PROJECTEUR D-ILA
DLA-VS2100/VS2100NL
For Customer use :
Enter below the serial No. which is
located on the side of the cabinet.
Retain this information for future
reference.
Model No. DLA-VS2100
DLA-VS2100NL
Serial No.
Instrucción para el cliente :
Introduzca a continuación el nº de
serie que aparece en la parte
inferior lateral de la caja. Conserve
esta información como referencia
para uso ulterior.
Modelo Nº DLA-VS2100
Nº de serie
DLA-VS2100NL
Pour utilisation par le client :
Entrer ci-dessous le N° de série qui
est situé sous le boîtier. Garder
cette information comme référence
pour le futur.
N° de modèle DLA-VS2100
N° de série
DLA-VS2100NL
ENGLISH FRANÇAIS ESPAÑOL/CASTELLANO
INSTRUCTIONS
MANUEL D’INSTRUCTIONS
MANUAL DE INSTRUCCIONES
D-ILA PROJECTOR
PROJECTEUR D-ILA
PROYECTOR D-ILA
DLA-VS2100
DLA-VS2100NL
ON
STAND BY
COMPONENT
COMP
.
HDMI 2
HDMI 1
ASPECT
PC
ANAMO
LENS.
AUTO
C.M.D
ALIGNMENT
CONTROL
HIDE
LIGHT
OK
BACK
MENU
PICTURE MODE
3D
DYNAMIC
NATURAL
USER1
USER3
USER2
USER5 USER6
USER4
PIC.
COLOR
LENS.
GAMMA
TEMP
ADJ.
AP
PC010685798-0
1
Getting started
Safety Precautions
IMPORTANT INFORMATION
This product has a High Intensity Discharge (HID) lamp that contains
mercury.
Disposal of these materials may be
regulated in your community due to
environmental considerations. For
disposal or recycling information,
please contact your local authorities or
for USA, the Electronic Industries
Alliance: http://www.eiae.org.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
WARNING:
THIS APPARATUS MUST BE EARTHED.
CAUTION:
To reduce the risk of electric shock, do not remove
cover. Refer servicing to qualied service personnel.
This projector is equipped with a 3-blade grounding
type plug to satisfy FCC rule. If you are unable to
insert the plug into the outlet, contact your
electrician.
MACHINE NOISE INFORMATION
(Germany only)
Changes Machine Noise Information Ordinance 3.
GSGV, January 18, 1991: The sound pressure level
at the operator position is equal or less than 20 dB
(A) according to ISO 7779.
FCC INFORMATION (U.S.A. only)
CAUTION:
Changes or modication not approved by JVC
could void the user’s authority to operate the
equipment.
NOTE:
This equipment has been tested and found to
comply with the limits for Class B digital devices,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protec
tion against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the instruc
tions, may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encourage to try to correct the
interference by one or more of the following
measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the
equipment and receiver.
● Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
● Consult the dealer or an experienced radio/
TV technician for help.
About the installation place
Do not install the projector in a place that cannot
support its weight securely.
If the installation place is not sturdy enough, the
projector could fall or overturn, possibly causing
personal injury.
IMPORTANT SAFEGUARDS
Electrical energy can perform many useful
functions. This unit has been engineered and
manufactured to assure your personal safety. But
IMPROPER USE CAN RESULT IN POTENTIAL
ELECTRICAL SHOCK OR FIRE HAZ ARD.
In order not to defeat the safeguards incorporated
into this product, observe the following basic rules
for its installation, use and service. Please read
these Important Safeguards carefully before use.
- All the safety and operating instructions should
be read before the product is operated.
- The safety and operating instructions should be
retained for future reference.
2
Getting Started
ENGLISH
150 mm and above
300 mm
and above
200 mm
and above
300 mm
and above
150 mm
and above
PORTABLE CART WARNING
(symbol provided by RETAC)
S3126A
- All warnings on the product and in the operating
instructions should be adhered to.
- All operating instructions should be followed.
- Place the projector near a wall outlet where the
plug can be easily unplugged.
- Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
- Do not use attachments not recommended by the
product manufacturer as they may be hazardous.
- Do not use this product near water. Do not use
immediately after moving from a low temperature
to high temperature, as this causes condensation,
which may result in re, electric shock, or other
hazards.
- Do not place this product on an unstable cart,
stand, or table. The product may fall, causing
serious injury to a child or adult, and serious
damage to the product. The product should be
mounted according to the manufacturer’s
instructions, and should use a mount recommend
ed by the manufacturer.
- When the product is used on a
cart, care should be taken to avoid
quick stops, excessive force,
and uneven surfaces which may
cause the product and cart to
overturn, damaging equipment or
causing possible injury to the
operator.
- Slots and openings in the cabinet are provided for
ventilation. These ensure reliable operation of the
product and protect it from overheating. These
openings must not be blocked or covered. (The
openings should never be blocked by placing the
product on bed, sofa, rug, or similar surface. It
should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is
provided and the manufacturer’s instructions have
been adhered to.)
- To allow better heat dissipation, keep a clearance
between this unit and its surrounding as shown
below. When this unit is enclosed in a space of
dimensions as shown below, use an air-conditioner
so that the internal and external temperatures are
the same. Overheating can cause damage.
Front
- power source indicated on the label. If you are
not sure of the type of power supply to your
home, consult your product dealer or local
power company.
- This product is equipped with a three-wire plug.
This plug will t only into a grounded power
outlet. If you are unable to insert the plug into
the outlet, contact your electrician to install the
proper outlet. Do not defeat the safety purpose
of the grounded plug.
- Power-supply cords should be routed so that
they are not likely to be walked on or pinched
by items placed upon or against them. Pay
particular attention to cords at doors, plugs,
receptacles, and the point where they exit from
the product.
- For added protection of this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from
the wall outlet and disconnect the cable system.
This will prevent damage to the product due to
lightning and power line surges.
- Do not overload wall outlets, extension cords, or
convenience receptacles on other equipment as
this can result in a risk of re or electric shock.
- Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short out parts that could result
in a re or electric shock. Never spill liquid of
any kind on the product.
- Do not attempt to service this product yourself
as opening or removing covers may expose you
to dangerous voltages and other hazards. Refer
all service to qualied service personnel.
- Unplug this product from the wall outlet and
refer service to qualied service personnel
under the following conditions:
a)When the power supply cord or plug is damaged.
b)If liquid has been spilled, or objects have fallen on
the product.
c)If the product has been exposed to rain or water.
d)If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the Operation
Manual, as an improper adjustment of controls may
result in damage and will often require extensive
work by a qualied technician to restore the product
to normal operation.
e)If the product has been dropped or damaged in any
way.
f) When the product exhibits a distinct change in
performance, this indicates a need for service.
- When replacement parts are required, be sure
the service technician has used replacement
parts specied by the manufacturer or with
same characteristics as the original part.
Unauthorized substitutions may result in re,
electric shock, or other hazards.
- Upon completion of any service or repairs to
this product, ask the service technician to
perform safety checks to determine that the
product is in proper operating condition.
3
1
Getting started
- The product should be placed more than one foot
away from heat sources such as radiators, heat
registers, stoves, and other products (including
ampliers) that produce heat.
- When connecting other products such as VCR’s,
and DVD players, you should turn off the power of
this product for protection against electric shock.
- Do not place combustibles behind the cooling fan.
For example, cloth, paper, matches, aerosol cans
or gas lighters that present special hazards when
over heated.
- Do not look into the projection lens while the
illumination lamp is turned on. Exposure of your
eyes to the strong light can result in impaired
eyesight.
- Do not look into the inside of this unit through
vents (ventilation holes), etc. Do not look at the
illumination lamp directly by opening the cabinet
while the illumination lamp is turned on. The
illumination lamp also contains ultraviolet rays and
the light is so powerful that your eyesight can be
impaired.
- Do not drop, hit, or damage the light-source lamp
(lamp unit) in any way. It may cause the light source lamp to break and lead to injuries. Do not
use a damaged light source lamp. If the light source lamp is broken, ask your dealer to repair it.
Fragments from a broken light-source lamp may
cause injuries.
- The light-source lamp used in this projector is a
high pressure mercury lamp. Be careful when
disposing of the light-source lamp. If anything is
unclear, please consult your dealer.
- Do not ceiling-mount the projector to a place which
tends to vibrate; otherwise, the attaching xture of
the projector could be broken by the vibration,
possibly causing it to fall or overturn, which could
lead to personal injury.
- Use only the accessory cord designed for this
product to prevent shock.
- Once every three years, please perform an
internal test. This unit is provided with
replacement parts needed to maintain its
function (such as cooling fans). Estimated
replacement time of parts can vary greatly
depending on frequency of use and the
respective environment. For replacement,
please consult your dealer, or the nearest
authorized JVC service center.
- When xing the unit to the ceiling, Please note
that we do not take any responsibility, even
during the warranty period, if the product is
damaged due to use of metal xtures used for
xation to the ceiling other than our own or if the
installation environment of said metal xtures is
not appropriate. If the unit is suspended from the
ceiling during use, please be careful in regard to
the ambient temperature of the unit. If you use
a central heating, the temperature close to the
ceiling will be higher than normally expected.
- Video images can burn into the electronic com
ponent parts. Please do not display screens with
still images of high brightness or high contrast,
such as found in video games and computer
programs. Over a long period of time it might
stick to the picture element. There is no problem
with the playback of moving images, e.g. normal
video footage.
- Not using the unit for a long time can lead to
malfunction. Please power it on and let it run
occasionally. Please avoid using the unit in a
room where cigarettes are smoked. It is impos
sible to clean optical component parts if they are
contaminated by nicotine or tar. This might lead
to performance degradation.
DO NOT allow any unqualied person
*
to install the unit.
Be sure to ask your dealer to install the unit
(e.g.attaching it to the ceiling) since special
technical knowledge and skills are required
for installation. If installation is performed by
an unqualied person, it may cause personal
injury or electrical shock.
4
Getting Started
Safety Precautions (Continued)
POWER CONNECTION
ENGLISH
For USA and Canada only
Use only the following power cord.
The power supply voltage rating of this product is
AC110V – AC240V. Use only the power cord
designated by our dealer to ensure Safety and EMC.
Ensure that the power cable used for the projector is
the correct type for the AC outlet in your country.
Consult your product dealer.
For United Kingdom For European continent
countries
Power cord
Power cord
WARNING:
Do not cut off the main plug from this
equipment.
If the plug tted is not suitable for the power points
in your home or the cable is too short to reach a
power point, then obtain an appropriate safety
approved extension lead or adapter or consult your
dealer. If nonetheless the mains plug is cut off,
dispose of the plug immediately, to avoid a possible
shock hazard by inadvertent connection to the main
supply. If a new main plug has to be tted, then
follow the instruction given below.
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT (Europe only):
The wires in the mains lead on this product are
colored Vert et jaune in accordance with the
following cord:
Green-and-yellow
Blue
Brown
As these colors may not correspond with the
colored making identifying the terminals in your
plug, proceed as follows:
The wire which is colored green-and-yellow must
be connected to the terminal which is marked M
with the letter E or the safety earth or colored
green or green-and-yellow. The wire which is
colored blue must be connected to the terminal
which is marked with the letter N or colored black.
The wire which is colored brown must be
connected to the terminal which is marked with the
letter L or colored red.
:Earth
:Neutral
:Live
POWER CONNECTION
(United Kingdom only)
HOW TO REPLACE THE FUSE:
When replacing the fuse, be sure to use only a
correctly rated approved type, re-t the fuse cover.
IF IN DOUBT —— CONSULT A COMPETENT
ELECTRICIAN.
Open the fuse compartment with the blade
screwdriver, and replace the fuse.
(* An example is shown in the illustration below.)
Fuse
Dear Customer,
This apparatus is in conformance with the valid European directives and standards regarding
electromagnetic compatibility and electrical safety.
European representative of Victor Company of Japan, Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany
5
1
Getting started
ENGLISH
Information for Users on Disposal of Old Equipment and Batteries
[European Union only]
These symbols indicate that equipment with these symbols
should not be disposed of as general household waste. If you
want to dispose of the product o r battery, please consider the
collection systems or fa cilities for appr opriate recycling.
Notice: The sign Pb below the symbol for batteries indicates that
this battery contains lead.
Products
Battery
DEUTSCH
Benutzerinformationen zur Entsorgung alter Geräte und Batterien
[Nur Europäische Union]
Diese Symbole zeigen an, dass derartig gekennzeichnete Geräte
nicht als normaler Haushaltsabfall entsorgt werden dürfen. We
nden Sie sich zur Entsorgung des Produkts oder der Batterie an
die hierfür vorgesehenen Sammelstellen oder Einrichtungen,
damit eine fachgerechte Wiederverwertung möglich ist.
Produkte
dass diese Batterie Blei enthält.
Batterie
Hinweis: Das Zeichen Pb unterhalb des Batteriesymbols gibt an,
FRANÇAIS
Informations relatives à l’élimination des appareils et des piles usagés, à
l’intention des utilisateurs
[Union européenne seulement]
Si ces symboles gurent sur les produits, cela signie qu’ils ne
doivent pas être jetés comme déchets ménagers. Si vous voulez
jeter ce produit ou cette pile, veuillez considérer le système de
collection de déc hets ou les centres de recyclage appropriés.
Notication: La marque Pb en dessous du symbole des piles
Produits
Pile
indique que cette pile contient du plomb.
NEDERLANDS
Informatie voor gebruikers over het verwijderen van oude apparatuur en
batterijen
[Alleen Europese Unie]
Deze symbolen geven aan dat appara tuur met dit symbool niet
mag worden weggegooid als algemeen huishoudelijk afval. Als u
het product of de batterij wilt weggooien, kun t u inzamelsystemen
of faciliteiten voor een geschikte recycling gebruiken.
Opmerking: Het teken Pb onder het batterijsymboo l geeft aan
dat deze batterij lood bevat.
Batterij
Producten
6
Getting Started
ENGLISH
ESPAÑOL / CASTELLANO
Información para los usuarios sobre la eliminación de baterías/pilas usadas
Estos símbolos indican que el equipo con estos símbolos no debe
desecharse con la basura doméstica. Si desea desechar el pro
ducto o batería/pila, acuda a los sistemas o centros de recogida
para que los reciclen debidamente.
Atención: La indicación Pb debajo del símbolo de batería/pila
indica que ésta contiene plomo.
Productos
Baterías/pilas
[Sólo Unión Europea]
ITALIANO
Informazioni per gli utenti sullo smaltimento delle apparecchiature e batterie
obsolete
[Solo per l’Unione Europea]
Questi simboli indicano che le apparecchiature a cui sono relativi
non devono essere smaltite tra i riuti domestici generici. Se si
desidera smaltire questo prodotto o questa batteria, prendere in
considerazione i sistem i o le strutture di raccolta appropriati per
il riciclaggio corretto.
Nota: Il simbolo Pb sotto il simbolo delle batter ie indica che
Prodotti
questa batteria contiene piombo.
Batteria
PORTUGUÊS
Informação para os utilizadores acerca da eliminação de equipamento usado e
pilhas
[Apenas União Europeia]
Estes símbolos indicam que o equipamento com estes símbolos
não deve ser eliminado juntamente com o restante lixo doméstico.
Se p retende eliminar o produto ou a pilha, utilize os sistemas de
recolha ou instalações para uma reciclagem apropriada.
Aviso: O sinal Pb abaixo do símbolo para pilhas indica que esta
pilha contém chumbo.
Produtos
Πληροφορίες για την απόρριψη παλαιού εξοπλισμού και μπαταριών
[ Ευρωπαϊκή Ένωση μόνο ]
Αυτά τα σύμβολα υποδηλώνουν ότι ο εξοπλισμός που τα φέρει
δεν θα πρέπει να απορριφθεί ως κοινό οικιακό απόρριμμα . Εάν
επιθυμείτε την απόρριψη αυτού του προϊόντος ή αυτής της
μπαταρίας , χρησιμοποιήστε το σύστημα περισυλλογής ή
εγκαταστάσεις για ανάλογη ανακύκλωση .
Σημείωση : Το σύμβολο Pb κάτω από το σύμβολο μπαταρίας
Προϊόντα
υποδηλώνει ότι η μπαταρία περιέχει μόλυβδο .
Pilha
ΕΛΛΗΝΙΚΑ
Μπαταρία
7
1
Getting started
Brugerinformation om bortskaffelse af gammelt udstyr og batterier
DANSK
Disse symboler angiver, at udstyr med disse symboler ikke må
bortskaffes som almindeligt husholdningsaffald. Hvis du ønsker at
smide dette produkt eller batteri ud, bedes du overveje at bruge
indsamlingssystem et eller steder, hvor der kan ske korrekt gen
brug.
Bemærk: Tegnet Pb under symbolet for batterierne angiver, at
Produkter
dette batteri indeholder bly.
Batteri
[Kun EU]
SUOMI
Tietoja vanhojen laitteiden ja akkujen hävittämisestä
[Vain Euroopan unioni]
Nämä symbolit ilmaisevat, että symboleilla merk ittyä laitetta ei
tulisi hävittää tavallisen kotitalousjätteen mukana. Jos haluat hävit
tää tuotteen tai sen akun, tee se hyödyntämällä akkujen
keräyspisteitä tai muita kier rätyspaikkoja .
Huomautus: Akkusymbolin alapuolella oleva Pb-merk intä tarkoit
taa, että akku sisältää lyijyä.
Tuotteet
Akku
SVENSKA
Information för användare gällande bortskaffning av gammal utrustning och
batterier
[Endast den Europeiska unionen]
Dessa symboler indikerar att utrustning med dessa symboler inte
ska hanteras som vanligt hushållsavfall. Om du vill bortsk affa
produkten eller batteriet ska du använda uppsamlingssystem eller
inrättningar för lämplig återvinning.
Observera! Märkningen Pb under symbolen för batterier indikerar
att detta batteri innehåller bly.
Batteri
Produkter
NORSK
Opplysninger til brukere om kassering av gammelt utstyr og batterier
[Bare EU]
Disse symbolene viser at utstyr med dette symbolet, ikke skal
kastes sammen med vanlig husholdningsavfall. Hvis du vil kass
ere dette produkte t eller batteriet, skal du vurdere å bruke innsam
lingssystemene eller andre muligheter for riktig gjenbruk.
Merk: Tegnet Pb under symbolet for batterie r, viser at batteriet
Produkter
inneholder bly.
Batteri
8
Getting Started
ENGLISH
Сведения для пользователей по утилизации старого оборудования и
батарей
[только для Европейского союза]
Данные символы указывают на то, что оборудование, на
которое они нанесены, не должны утилизироваться, как
обычные бытовые отходы. При необходимости утилизировать
такое изделие или батарею обратитесь в специальный пункт
сбора для их надлежащей переработки.
Уведомление: Надпись Pb под символом батар ей указывает
Изделия
на то, что данная батарея содержит свинец.
Батарея
Informace pro uživatele k likvid aci starého zařízení a baterií
[Pouze Evropská unie]
Tyto symboly označují, že produkty s těmito symboly se nesmí
likvidovat jako běžný odpad. Pokud chcete produkt nebo baterii
zlikvidovat, využijte sběrný systém nebo jiné zařízení, které zaji stí
řádnou recyklaci.
Upozornění: Značka Pb pod symbolem pro ba te rie znamená, že
Produkty
tato baterie obsahuje olovo.
Baterie
Informacje dla użytkowników dotyczące poz bywania się zużytego sprzętu i
baterii
[Tylko kraje Unii Europejskiej]
Te symbole oznaczają, że sprzę tu nie należy wyr zucać razem z
odpadami gospodarczymi. Jeśli trzeba po zbyć się tego produktu
lub ba terii, proszę skorzystać z systemu odbioru lub urządzeń do
zbió rki odpadów elektronicznych, w celu odpowiedniego ponowne
go ich przetworzenia.
Uwaga: Oznaczenie Pb, znajdujące się pod symbole m baterii
Produkty
wskazuje, że ta bateria zawiera ołów.
Felhasználói információ az elhasznált be rendezések és akkumulátorok
elhelyezéséről
[Csak az Európai Unióban]
Ez a szimbólum azt jelzi, hogy a berendezés nem helyezhető az
általános háztartási hulladék közé. Ha meg szeretne szabadulni a
terméktől vagy az akkumulátortól, akkor legyen tekintettel az
gyűjtő rendszerre vagy intézményekre a megfelelő hasznosítás
érdekében.
Megjegyzés: Az alábbi Pb szimbólum - ha az akkum ulátoron
Termékek
megtalálható - azt jelzi, hogy az akkumulátor ólmot
tartalmaz.
POLSKI
Bateria
MAGYAR
Akkumulátor
9
1
Getting started
Contents
Getting started
Safety Precautions ...........................2
Contents .........................................10
Accessories/Optional
Accessories ....................................11
Check the Accessories .............................. 11
Optional Accessories ................................. 11
Controls and features ....................12
Main body - Front ......................................12
Main body - Bottom ...................................12
Main body - Rear ....................................... 13
Main body - About the indicator display .....14
Main body - Warning display and
conrmation/response ...............................15
Main body - Input terminal ......................... 16
How to insert batteries into the remote
control ........................................................ 17
Preparation
About installation ...........................18
IImportant points concerning the
installation .................................................18
Installing the Projector and Screen ...........19
Set Angle ................................................19
VS21
RS50RS50
Shift
Fixation of the projector ............................. 20
Screen Size and Projection Distance
Effective Range of Remote Control Unit....21
.................................................19
VS21
RS50RS50
.21
About the connection .....................22
Types of possible input signals
(PC compatible) ......................................... 22
Connection to the unit ...............................23
Connection of the power cord (provided) ..29
Operation
Basic Operation ..............................30
Basic operation procedures ....................... 30
Frequently used useful functions ............... 32
Setting the Screen Size ............................. 32
Masking the Surrounding Area of
an Image ...................................................33
Temporary turning-off of the video ............. 34
Adjustments and settings
in the menu .....................................35
Structure of the menu hierarchy
(summary) .................................................35
Menu operation button ..............................41
Menu operation procedure ........................42
Menu item description ...............................43
Operation guide (glossary) ............52
Maintenance
Explanation of the installation/
removal of the lamp attachment ..54
Lamp attachment replacement
procedures ................................................ 54
Lamp attachment removal procedure ....... 56
Attachment of the installation
verication seal .......................................... 57
Replacing the Lamp .......................58
Lamp replacement procedure ...................58
Resetting lamp Time ..................................60
Method for cleaning and
replacing lters ...............................62
Others
Troubleshooting .............................64
In case this message is
displayed .........................................66
RS-232C Interface ...........................67
RS-232C Specications ............................67
TCP/IP-connection ....................................67
Command Format .....................................68
RS-232C Communication Examples ......... 70
Copyright and Caution ...................71
About Trademarks and Copyright ..............71
Caution ......................................................71
Specications .................................72
Dimensions ................................................ 74
Index ................................................75
CAUTION
About the marks used in this
book
VS21
RS50RS50
Compatible only with
DLA-VS2100
RS50RS50
VSNL
Compatible only with
DLA-VS2100NL
10
Getting Started
ENGLISH
Accessories/Optional Accessories
Check the Accessories
Remote Control ..........................................................................1 piece
AAA size Batteries (for operation conrm)..................................2 pieces
Power Cord For the US market (2 m) .........................................1 piece
Power Cord For the EU market (2 m) .........................................1 piece
Power Cord For the UK market (2 m) .........................................1 piece
Lamp Attachment .......................................................................1 piece
Installation Verication Seal........................................................1 piece
●
warranty card and other printed material are also included.
Optional Accessories
Please check with your authorized dealer for details.
●
Replacement Lamp: PK-L2210U
●
Replacement Filter: PC010661199
●
Replacement lamp attachment: PC010685599
11
1
Getting started
Controls and features
Main body - Front
③ Indicator
STANDBY/ON LAMP WARNING
④ Exhaust Vent
② Remote receiver (front)
VS21
① Lens
This is a projection lens. Please do not look
inside during projection.
RS50RS50
③ Indicator
Please see “About the indicator display” for
details. (Reference page: 14)
① Lens
VS21
RS50RS50
④ Exhaust
Vent
② Remote receiver (front)
Please aim the remote control at this area when
using it.
* There is also a remote receiver at the rear.
Main body - Bottom
⑤ Inlets
⑥ Feet
④ Exhaust Vent
Warm air ows out in order to cool the interior of
the set. Please do not block the vents.
⑤ Inlets (at 3 points on the rear/
bottom)
In order to cool the inside of the unit, air is let
inside. Do not block or prevent the outow of
hot air. Doing so could lead to failure of the unit.
* There are inlets at two points on the right and
left sides of the rear side. (Reference page: 13)
⑥ Feet
The height (0 to 5 mm) can be adjusted by
turning the foot.
12
Getting Started
ENGLISH
Controls and features (continued)
Main body - Rear
⑤ Inlets
⑧ Lamp Cover
⑤ Inlets
⑦ Input
terminal
⑪ Power input
terminal
⑦ Input terminal
There is also a terminal other than the input
terminal for video images, such as those used
for controlling or optional equipment. Please see
“
About input terminals” for detailed information
about terminals. (Reference page: 16)
⑧ Lamp Cover
When replacing the light source lamp, remove
this cover. (Reference page: 58)
⑨ Operation panel
See the following illustration “Control panel” for
more details.
Operation panel
■
⑨ Operation panel
⑩ Light receiving section
of the remote control (rear)
⑩ Light receiving section of the
remote control (rear)
Please aim the remote control at this section
when using.
* There is also a light receiving section at the
rear.
⑪ Power input terminal
This is the power input terminal. It is
connected via the supplied power cord.
(Reference page: 29)
STANDBY/ON
To turn on/off the power
INPUT
To switch input
OK
To select or conrm
Left button
Down button
To display the menu
MENU
BACK
Up button
Right button
eturn to the previous menu
To r
13
1
Getting started
Controls and features (continued)
Main body - About the indicator display
Warnings and indications used during normal operation mode of this unit are displayed with the indicators
for [STAND BY / ON], [LAMP], [WARNING] at the front of this unit.
Meaning of the lighting gures:
The display the indicator lights.
They display ashing of the indicator.
Operation mode display
Displays the color and lighting/ashing of the [STAND BY / ON] indicator.
STAND BY
Duringstandby
STANDBY/ON
STAND BY
When"Hide"issettoON
STANDBY/ON
Light on(Red)
LAMP WARNING
Blinking(Green)
LAMP WARNING
STAND BY
Whileactivatingthelamp
(about1minute)
STANDBY/ON
All Off
Duringimageprojection
STANDBY/ON
Light on(Green)
LAMP WARNING
LAMP WARNING
STAND BY
Duringcooldown
STANDBY/ON
Blinking(Red)
LAMP WARNING
Criterion indication of the lamp replacement
Displays lighting/ashing of the [LAMP] indicator. Moreover, the [STAND BY / ON] indicator, which shows
the operation mode of this unit, is displayed as described above. (Reference page: 72)
LAMP Light on(orange)
Lamp replacement is
near(When accumulated lamp
time has exceeded 2900 hours)
STANDBY/ON
LAMP WARNING
14
Getting Started
ENGLISH
Controls and features (continued)
Main body - Warning display and conrmation/response
Warning display
You are informed of the contents of warning notices by the (repeated) displays of the [WARNING] and
[LAMP] indicators. Moreover, the [STAND BY / ON] indicator, which shows the operating mode of the unit,
is displayed simultaneously as described above.
Upon activation of the warning mode, the projection is interrupted at the same time for about 60 seconds
and the cooling fan is turne
cooling fan has stopped. Subsequently, please perform the following checks and take appropriate
countermeasures.
d on. Please disconnect the power plug from the electric socket after the
Lighting/flashing lights
status diagram
STANDBY/ON
LAMP WARNING
red
(
) (
red
red
)
)
Mode
display
STANDBY/ON
Mode
display
STANDBY/ON
Mode
display
(*)
LAMP WARNING
orange
(
ultaneous
Sim
ashing
LAMP WARNING
orange
(
) (
Blinking
Frequency
1 time
2 times Cooling fan stops
3 times
4 times
1 time
2 times
)
3 times
1 time
2 times
3 times
Abnormalities in the power
supply
Internal temperature is too
high
External temperature is
too high
Abnormal electrical circuit
Lamp does not light up
and unit is unable to
project
Lamp is turned off during
projection
Lamp cover is removed
Content
Conrmation and
countermeasures
●
Check that nothing is
blocking the air inlets.
●
Check that the external
temperature is normal.
Action
Leave the unit until it cools
down.
After that, turn on the power
again.
●
Check that an impact shock
has not occurred during
operation.
●
Check that the lamp
unit and lamp cover are
correctly installed.
Action
Turn on the power again.
If the warning indication is displayed again, please wait for the cooling fan stopped, then pull out the power
plug from the power outlet. Then call your authorized dealer for repair.
(*)If the scheduled time for the replacement of the lamp is exceeded, the light might light up.
15
1
Getting started
Controls and features (continued)
Main body - Input terminal
① HDMI 1 ② HDMI 2 ③ LAN
⑤ COMPONENT
④ RS-232C
⑧ REMOTE
⑥ PC
① HDMI 1 Terminal
You can connect a device equipped with HDMI
output, etc. It is tted to the M3 lock hole.
Screw hole depth 3mm. (Reference page: 24)
② HDMI 2 Terminal
You can connect a device equipped with HDMI
output, etc. It is tted to the M3 lock hole.
Screw hole depth 3mm. (Reference page: 24)
③ LAN terminal “RJ-45”
This is a LAN-terminal. If one connects an
external PC, it is possible to control this unit by
sending control commands.
(Reference page: 28)
④ RS-232C terminal (male D-Sub 9
pin)
This is a RS-232C interface standard terminal.
If one connects an external PC, it is possible to
control this unit. (Reference page: 27)
⑤ COMPONENT terminal “RCAx3”
It is also used as input terminal for analog
RGB (G on Sync) signals, component (Y, Cb,
Cr) signals, DTV format (Y, Pb, Pr) signals. It
can also be connected with devices, which are
equipped with signal output, etc. (Reference
page: 25)
⑦ TRIGGER
⑥ PC terminal “D-Sub 15 pin”
This is an input term used for Personal Computer
(PC) signals only (RGB video signals and sync
signals). Use to connect a computer display
output terminal, etc. (Reference page: 26)
⑦ TRIGGER terminal( )
DC power supply output terminal with DC12V,
100mA. It is used for output signals which
control the vacillating screen responding to the
SCREEN TRIGGER. Please note it can cause
damage to your equipment if the connection is
done incorrectly. (Tip = DC +12 V, Sleeve = GND)
(Reference Page: 27, 50)
⑧ REMOTE terminal to “Stereo mini
jack”
In case it is impossible to use the remote control
due to the installation of this unit’s dedicated
BOX or rear projection, one can set up an
external light receiving section. It is used to
connect this external receiver and this unit. There
is no such product as an external light receptor.
Therefore, please consult your authorized JVC
service center. (Reference page: 28)
16
Getting Started
ENGLISH
BACK
HIDE
LIGHT
C.M.D
PC
HDMI 1
STAND BY
ASPECT
HDMI 2
ANAMO
COMP
.
LENS.
CONTROL
MENU
GAMMA
AP
LENS.
ADJ.
PIC.
ON
NATURAL
3D
USER4
USER5 USER6
PICTURE MODE
COMPONENT
TEMP
COLOR
AUTO
ALIGNMENT
DYNAMIC
USER1
USER2
USER3
Controls and features (continued)
■
Remote Control
To turn off the power
To set the screen size
(Reference page: 32)
VS21
RS50RS50
To control lens
(Reference page: 30)
To hide the image
temporarily(Reference
page: 34)
To display/close the menu
(Reference page: 41)
To adjust color temperature
To set gamma
To turn on the power
To select input mode
(Reference page: 30)
Clear Motion Drive
Auto Alignment
(Reference page: 48)
To illuminate buttons on the remote
control for 7 second
To select or conrm
To return to the previous menu
(Reference page: 41)
To switch picture mode
Lens Aperture
Sequentially switched picture
adjust items, such as contrast and
brightness.The switching items are
not the same for different models, or
different picture modes.
How to insert batteries into the remote control
①
●
●
●
If the remote control has to be brought closer to the projector to operate, it means that the batteries are
wearing out.
When this happens, replace the batteries. Insert the batteries according to the
Be sure to insert the end rst.
If an error occurs when using the remote control, remove the batteries and wait for 5 minutes. Load the
batteries again and operate the remote control.
②
③
marks.
17
2
CAUTION
CAUTION
CAUTION
Preparation
About installation
Important points concerning the installation
Please read the following carefully before the installation of this unit.
Installation environment
This unit is a precision device. Therefore, please refrain
from installation or use in the following locations.
Otherwise, it may cause re or malfunction.
• Dust, wet and humid locations.
• Sooty or cigarette smoke lled locations.
• On top of a carpet or bedding, or other soft surfaces.
• Locations with high temperatures - as located in direct
sunlight.
• Locations with high or low temperatures.
Permissible operating temperature range: +5 º to +35º .
Relative humidity range permissible for operating: 20%
~ 80% (non-condensing) .
Storage temperature tolerance: -10º to +60º.
• If the installation of the unit is done in a room with soot
and/or smoke over a longer period, even small amounts
of these substances will affect the device.This unit
cools its optical components, which produce a great
amount of heat, by sucking in air. If the optical circuits
get dirty, this might lead to malfunctions, like the video
images becoming darker or a deterioration of the color
development. Dirt sticking to the optical components
cannot be removed.
Please be careful to perform
the installation at a certain
distance from walls and
other devices
For better heat dissipation, please keep a minimum
distance between this unit and its surroundings as shown
the following illustration.
in
Moreover, please open the front of the unit. If there are
any objects in front of the exhaust port, the hot air will
ow back to the unit and heat it. The hot air owing out of
the unit might cause shadows on the screen (heat haze
phenomenon).
Moreover, when it is enclosed in a space as shown in the
following illustration, please make sure that the enclosed
interior has the same temperature as the outside. High
temperatures might lead to failure of the unit.
Please be careful when using
This unit uses a projection lamp, which will get hot when
in use. Please refrain from projecting in the following
circumstances.
Otherwise, it might cause re or malfunction.
• Projection while lying on its side.
Please avoid projection if the installation of the unit is
done at an excessive angle of more tha
cause harm to the life of the lamp and color shading.
• Please avoid projection at a location where the air vents
or exhaust ports might get blocked.
Please choose a non-uniform cloth material for the screen.
If you choose something uniform, like something with a
checkered pattern, there might be interference with the
pixel array of the D-ILA components. One way to reduce
the interference pattern is to change the size of the screen,
so that it will not be so noticeable.
n ± 90 °. It may
Inclination adjustment
for this unit
How to adjust the vertical angle
Height and inclination of the unit (0 ~ 5mm) can be
adjusted by rotating its feet. Lift the unit and adjust
the four feet.
18
300 mm
and above
150 mm
and above
Front
150 mm and above
300 mm
and above
200 mm
and above
Stand
Extend Contract
ENGLISH
Horizontal lens shift
About installation (Continued)
Installing the Projector and Screen
While installing, please place this unit and the screen perpendicular to each other. Failing
to do so may increase trapezoidal distortion.
Set Angle
As shown in the illustration, this unit can be installed
with a tilted angle, but for some areas there might be
other conditions. Moreover, depending on the angle of
installation, it may be necessary to have a hanging metal
mount and secure installation base depending on the angle
of the installation.
Area A: The range where installation is possible.
Area B: The necessary range for the installation of the
lamp attachment. Please make sure to use the
supplied lamp attachment. (Reference page: 54)
Failure to attach it might cause equipment failure.
VS21
Shift
■
*
RS50RS50
Left/Right position
0% up/down position (center)
■
Up/Down position
*
Downward slope
of 45 °
0% left/right position (center)
Area A
Area B
Downward slope
of 45 °
Preparation
Approximately 34%
(maximum) of the
projected image
Approximately 34%
(maximum) of the
projected image
Lens shift correlation chart:
Left-Right Shift(%)
Up-Down Shift(%)
●
Maximum Up-Down shift varies with the amount of Left-Right shift.
Likewise, maximum Left-Right shift varies with the amount of UpDown shift.
●
The values on the chart are intended to act as a guide. Use them
for reference during installation.
0% 10% 20% 30% 34%
80% 66% 47% 18% 0%
Approximately 80%
(maximum) of the
projected image
Approximately 80%
(maximum) of the
projected image
■
Lens shift movement
range
90
80
70
60
Vertical lens shift（％）
50
40
30
20
Lens movability
10
range
0 10 20
30 40
（％）
19
2
Preparation
About installation (Continued)
Fixation of the projector
Measures to prevent the unit from toppling or dropping should be taken for safety reasons and
accident prevention during emergencies including earthquakes.
When mounting this unit on a pedestal or ceiling, remove the 4 feet on the bottom surface and
use all the 4 screw holes (M5 screws) to mount.
Ceiling
Precautions for Mounting
●
Special expertise and techniques are required for
mounting this unit. Be sure to ask your dealer or a
specialist to perform mounting.
●
Depth of the screw holes (screw length) is 23
mm. Use screws shorter than 23 mm but longer
than 13 mm.
Using other screws will result in
malfunctioning or cause the unit to drop.
●
When mounting to a pedestal, ensure
sufcient space (foot height of 10 mm or
higher) around the unit so that the air inlets
are not blocked.
●
Do not tilt this unit more than ±5 degrees
from side to side when using.
■
Bottom Surface
4 locations
Air inlets
●
Regardless whether the unit is still under
guarantee, JVC is not liable for any product
damage caused by mounting the unit with non-
JVC ceiling ttings or when the environment is
not suitable for ceiling-mount.
●
When using the unit hanging from a ceiling,
pay attention to the surrounding temperature.
When a heater is in use, temperature around
the ceiling is higher than expected.
20
ENGLISH
30°
30°
20°
20°
About installation (Continued)
VS21
Screen Size and Projection Distance
Determine the distance from the lens to the screen to achieve your desired screen size.
This unit uses a 2.0x power zoom lens for projection.
■
Relationship Between Projection Screen Size and Projection Distance
RS50RS50
Pr o je c ti o n Sc re e n
Size
(Height, Width)
Aspect Ratio 16:9
"
60
Approx.
(
(Approx.0.9, 1.5m)
(Approx.1.0, 1.8m)
(Approx.1.1, 2.0m)
(Approx.1.2, 2.2m)
(Approx.1.4, 2.4m)
(Appro
(Approx.1.6, 2.9m)
0.7, 1.3m)
70"
80"
90"
100"
110"
120"
x.1.5, 2.7m)
130"
A p pr o x im a t e P r oj e c ti o n
Distance
W(Wide) to T(Tele)
Approx.1.78m to
Approx.3.66m
Approx.2.09m to Approx.4.28m
Approx.2.40m to Approx.4.89m
Approx.2.70m to Approx.5.51m
Approx.3.01m to Approx.6.13m
Approx.3.31m to Approx.6.75m
Approx.3.62m to Approx.7.36m
Approx.3.92m to Approx.7.98m
Projection Screen Size
(Height, Width)
Aspect Ratio 16:9
140"
(Approx.1.7, 3.1m)
150"
(Approx.1.9, 3.3m)
160"
(Approx.2.0, 3.5m)
170"
(Approx.2.1, 3.8m)
180"
(Approx.2.2, 4.0m)
190"
(Approx.2.4, 4.2m)
200"
(Approx.2.5, 4.4m)
Effective Range of Remote Control Unit
A p pr ox im at e P r oj e c ti o n
Distance
W(Wide) to T(Tele)
Approx.4.23 m to
Approx.8.60m
Approx.4.53m to
Approx.9.22m
Approx.4.84m to
Approx.9.84m
Approx.5.14m to
Approx.10.45m
Approx.5.45m to
Approx.11.07m
Approx.5.75m to
prox.11.68m
Ap
Approx.6.06m to
Approx.12.30m
Preparation
When directing the remote control toward this
■
unit.
●
When aiming the remote control towards the
remote sensor on this unit, ensure that the
distance to the sensor in front or at the rear of
this unit is within 7 m.
●
If the remote control fails to work properly, move
closer to this unit.
When reecting off a screen
■
●
Ensure that the total of distance A between this
unit and screen and distance B between remote
control and screen is within 7 m.
●
As the efciency of signals reected from the
remote control unit differ with the type of screen
used, operable distance may decrease.
Screen
This unit
20°
A
20°
B
Remote control
30°
Remote control
30°
This unit
21
2
Preparation
About the connection
Types of possible input signals (PC compatible)
●
HDMI
No.
Designation
1
2
3
4
5
6
7
8
WSXGA
9
●
PC (D-sub 3-lines 15 pins)
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19 1920x1080 60 1920 X 1080 67.500 60.00 148.500 2200 1125 1920 1080
20
21
22
60 640 X 480 31.500 60.000 25.200 800 525 640 480
VGA
59.94 640 X 480 31.469 59.940 25.175 800 525 640 480
VGA
SVGA
60 1024 X 768 48.363 60.004 65.000 1,344 806 1,024 768
XGA
WXGA
+60 1440 X 900 55.919 59.999 106.470 1,904 932 1,440 900
WXGA
SXGA
WUXGA
Designation
VGA
VGA
VGA
VGA
SVGA
SVGA
SVGA
SVGA
SVGA
XGA
XGA
XGA
XGA
WXGA
WXGA+
SXGA
SXGA+
WSXGA+
13" 640 X 480 35.000 66.667 30.240 864 525 640 480
MAC
16" 832 X 624 49.107 75.087 55.000 1120 654 832 624
MAC
19" 1024 X 768 60.241 74.927 80.000 1328 804 1024 768
MAC
Resolution
60 800 X 600 37.879 60.317 40.000 1,056 628 800 600
60 1280 X 768 47.760 60.000 79.998 1,675 796 1,280 768
60 1280 X 1024 63.981 60.020 108.000 1,688 1,066 1,280 1,024
+60 1680 X 1050 65.222 60.002 147.140 2,256 1,087 1,680 1,050
60 1920 X 1200 74.038 59.95 154.000 2,080 1,235 1,920 1,200
Resolution
60 640 X 480 31.500 60.000 25.175 800 525 640 480
72 640 X 480 37.900 72.000 31.500 832 520 640 480
75 640 X 480 37.500 75.000 31.500 840 500 640 480
85 640 X 480 43.300 85.000 36.000 832 509 640 480
56 800 X 600 35.200 56.000 36.000 1024 625 800 600
60 800 X 600 37.900 60.000 40.000 1056 628 800 600
72 800 X 600 48.100 72.000 50.000 1040 666 800 600
75 800 X 600 46.900 75.000 49.500 1056 625 800 600
85 800 X 600 53.700 85.000 56.250 1048 631 800 600
60 1024 X 768 48.400 60.000 65.000 1344 806 1024 768
70 1024 X 768 56.500 70.000 75.000 1328 806 1024 768
75 1024 X 768 60.000 75.000 75.750 1312 800 1024 768
85 1024 X 768 68.700 85.000 94.500 1376 808 1024 768
60 1280 X 768 47.760 60.000 79.998 1675 796 1280 768
60 1440 X 900 55.919 59.999 106.470 1904 932 1440 900
60 1280 X 1024 64.000 60.000 108.000 1688 1066 1280 1024
60 1400 X 1050 63.981 60.020 108.000 1688 1066 1400 1050
60 1680 X 1050 65.222
fh
[kHz]fv[Hz]
fh
[kHz]
60.002 147.140 2256 1087 1680 1050
dot CLK
[MHz]
fv
[Hz]
Total No.
of dots
[dot]
dot CLK
[MHz]
Total No.
Total No.
of dots
[dot]
of lines
[line]
Total
No. of
lines
[line]
No. of
effective
dots
[dot]
No. of
effective
dots
[dot]
effective
lines [line]
lines [line]
No. of
No. of
effective
22
ENGLISH
About the connection (Continued)
Connection to the unit
●
Do not turn on the power until connection is complete.
●
The connection procedures differ according to the device used. For details, refer to the instruction
manual of the device to be connected.
●
This device is used for image projection. Connect to an audio output device such as amplier and
speaker for audio output from the connected device.
●
The images may not be displayed depending on the devices and cables to be connected.
For HDMI cable (sold separately), only use one that is HDMI-approved.
●
It may not be possible to connect to this unit depending on the dimension of the connector cover of the
cables to be connected.
BD/DVD Recorder BD/DVD Player
Preparation
To connect via HDMI
terminal
(Reference page: 24)
To connect RS232C terminal
(Reference
page: 27)
Connection by LAN terminal (Reference page: 28)
To connect via video terminal
STANDBY/ON
1 HDMI 2
RS-232-C
C
R/PR CB/PB Y
PC
TRIGGER
REMOTE
CONTROL
INPUT
OK
MENU
BACK
Connection by REMOTE terminal (Reference page: 28)
To connect via Trigger terminal
To connect via PC terminal
(Reference page: 26)
(Reference page: 27)
(Reference page: 25)
PC
VCR and
camcorder
23
2
1 HDMI 2
RS-232-C
C
R/PRCB/PB
Y
PC
TRIGGER
REMOTE
CONTROL
STANDBY/ON
MENU
BACK
INPUT
OK
1 HDMI 2
RS-232-C
C
R/PRCB/PB
Y
PC
TRIGGER
REMOTE
CONTROL
STANDBY/ON
MENU
BACK
INPUT
OK
Preparation
About the connection (Continued)
■
Connecting via HDMI Cable
This unit
Notebook PC
BD/DVD recorder
HDMI 1 input terminal
HDMI 2 input terminal
HDMI output terminal
HDMI cable (sold separately)
●
If noise is produced, take PCs (Notebook PC) away from this unit.
●
For a transmission bandwidth in compliance with the HDMI standard, a 340MHz cable is recommended
In case a cable is used for transmission bandwidth of 75MHz, it is recommended to choose 1080i or less
for the transmitting equipment.
●
If the video is not displayed, try to reduce the length of the cable or lowering the resolution of the video
transmitting equipment.
■
Connecting via HDMI-DVI Conversion Cable
This unit
Desktop computer
HDMI 1 input terminal
HDMI 2 input terminal
●
If noise is produced, take PCs (desktop computer) away from this unit.
●
If the video is not displayed, try to reduce the length of the cable or lowering the resolution of the video
HDMI-DVI conversion cable
(sold separately)
DVI output terminal
transmitting equipment.
24
About the connection (Continued)
C
Connecting via Component Video Cable
■
This unit
STANDBY/ON
INPUT
OK
1 HDMI 2
RS-232-C
C
R/PR CB/PB Y
PC
TRIGGER
REMOTE
CONTROL
MENU BACK
To component video input terminals
Component video cable
(sold separately)
●
Set “COMP.” in the setting menu to “Y Pb/Cb Pr/Cr”.
(Reference page: 48)
BD/DVD player
Component video output terminals
C
R/PR
C
B/PB
Y (green)
ENGLISH
Preparation
(red)
(blue)
■
Connecting via RGB Video Cable
This unit
STANDBY/ON
1 HDMI 2
RS-232-C
C
R/PR CB/PB Y
PC
REMOTE
TRIGGER
CONTROL
To RGB video input terminals
INPUT
OK
MENU
BACK
RGB video cable
(sold separately)
●
Set “COMP.” in the setting menu to “RGB”. (Reference page: 48)
●
For information on compatible input signals, see “Specications”.(Reference page: 72)
Device equipped with
RGB video output terminals
R(Red)
B(Blue)
G(Green)
signals)
RGB output
(Includes sync
25
2
1 HDMI 2
RS-232-C
C
R/PRCB/PB
Y
PC
TRIGGER
REMOTE
CONTROL
STANDBY/ON
MENU
BACK
INPUT
OK
Preparation
About the connection (Continued)
■
Connecting via PC Cable
This unit
Notebook PC
To PC input terminal
PC cable(sold separately
●
For information on supported input signals, please refer to “Specications
)
VGA output terminal
(Reference page: 72)
”.
26
ENGLISH
1 HDMI 2
RS-232-C
C
R/PRCB/PB
Y
PC
TRIGGER
REMOTE
CONTROL
STANDBY/ON
MENU
BACK
INPUT
OK
1 HDMI 2
3D
C
R/PRCB/PB
Y
SYNCHRO
PC
TRIGGER
REMOTE
CONTROL
STANDBY/ON
MENU
BACK
INPUT
OK
About the connection (Continued)
■
Connecting via Trigger Cable
This unit
Screen
To Trigger output terminal
Trigger cable
(sold separately)
CAUTION
Trigger input terminal
(Φ3.5)
Preparation
●
Do not supply the power to the other devices.
●
Do not connect audio terminals of the other devices such as headphones etc. Otherwise, this may
cause a malfunction of the other devices or injury.
●
Using beyond the rated value will cause malfunction.
● Exercise adequate caution to prevent short circuit as the trigger terminal outputs a voltage of 12V.
●
The default is set to "No output". Please set it under the item "Trigger" of menu [5] "Function" (Reference
page: 50).
■
Connected by RS-232C connection cable
This unit
RS-232C connection cable (sold separately)
RS-232C
terminal
27
2
1 HDMI 2
RS-232-C
C
R/PR CB/PB Y
PC
TRIGGER
REMOTE
CONTROL
STANDBY/ON
MENU
BACK
INPUT
OK
Preparation
About the connection (Continued)
■
Connected by LAN terminal
This unit
HUB
connection cable
(sold separately)
STANDBY/ON
1 HDMI 2
C
R/PR CB/PB Y
RS-232-C
REMOTE
TRIGGER
PC
●
The network is used to control the unit. It is not used for transmission of the video signal.
●
Please contact your network administrator for questions concerning the network connection.
CONTROL
INPUT
OK
MENU
BACK
Network
Server
■
Connected by a REMOTE terminal
This unit
External infrared sensor
connection cable(sold separately)
●
For an external infrared sensor and connecting cable, please contact your dealer or a JVC service
center.
(sold separately)
28
ENGLISH
1 HDMI 2
RS-232-C
C
R/PRCB/PB
Y
PC
TRIGGER
REMOTE
CONTROL
STANDBY/ON
MENU
BACK
INPUT
OK
Power Cord
(Supplied)
About the connection (Continued)
Connection of the power cord (provided)
Once you have connected the equipment, connect the projector power cord.
1 Connect the power cord supplied with the
unit power input terminal
2 Connect to the power outlet
1
2
Be carful to avoid re and electric shocks
● As the amount of electrical energy for this unit is large, please connect it directly into
the wall outlet.
CAUTION
● When you are not using the equipment, please unplug the power cord.
● Connect it only with the provided power cord.
● Do not use voltage other than the indicated power voltage.
● Do not damage, break or modify the power cord. Moreover, the power cord will be
damaged if you place it under heavy objects, heat or pull it.
● Do not unplug with wet hands.
Preparation
29
3
BACK
HIDE
LIGHT
C.M.D
PC
HDMI 1
STAND BY
ASPECT
HDMI 2
ANAMO
COMP
.
LENS.
CONTROL
MENU
GAMMA
AP
LENS.
ADJ.
PIC.
ON
NATURAL
3D
USER4
USER5 USER6
PICTURE MODE
COMPONENT
TEMP
COLOR
AUTO
ALIGNMENT
DYNAMIC
USER1
USER2
USER3
INPUT
LENS
LENS
Operation
Basic Operation
Basic operation procedures
6
1
2
3
4
5
Once you have nished the basic setup, the unit can normally be
used just with the following operations.
Turn on power source
1
ON
STANDBY/ON
Light on (Green)
●
You can also press the
on the power
Choose the projected image
2
1
Select input mode
●
You can also select the input mode by pressing the
. (Reference page: 13)
button on the unit to turn
button on the unit. (Reference page: 13)
HDMI 1
Play back the selected device
2
Adjust the zoom (screen size)
3
HDMI 2 COMP. PC
VS21
RS50RS50
30
Lens Control
Zoom
Exit
MENU
Select
Operate
Back
Adjust accordingly
BACK
by pressing the up/
down buttons
STANDBY/ON
LAMP
WARNING
VS21
Adjust the focus (focal point)
4
Lens Control
Focus
Select
Exit
MENU
Operate
Adjust accordingly
Back
BACK
by pressing the up/
RS50RS50
down buttons
Loading...