JVC DLA-RS2 User Manual [en, es, fr]

ENGLISH FRANÇAIS ESPAÑOL

D-ILA PROJECTOR
PROJECTEUR D-ILA
PROYECTOR D-ILA

DLA-RS2

INSTRUCTIONS

MANUEL D’INSTRUCTIONS

MANUAL DE INSTRUCCIONES

Getting Started Preparation Basic Operation Settings Troubleshooting Others

For Customer use :

Enter below the serial No. which is
located on the bottom side of the
cabinet. Retain this information for
future reference.

Model No. DLA-RS2

Serial No.

Pour utilisation par le client :

Entrer ci-dessous le N° de série qui
est situé sous le boîtier. Garder
cette information comme référence
pour le futur.

N° de modèle DLA-RS2

N° de série

Instrucción para el cliente :

Introduzca a continuación el nº de
serie que aparece en la parte
inferior lateral de la caja. Conserve
esta información como referencia
para uso ulterior.

Modelo Nº DLA-RS2

Nº de serie

LCT2344-001B

1

Getting Started

Safety Precautions

IMPORTANT INFORMATION

This product has a High Intensity
Discharge (HID) lamp that contains
mercury.

Disposal of these materials may be
regulated in your community due to
environmental considerations. For
disposal or recycling information, please
contact your local authorities or for USA,
the Electronic Industries Alliance:
http://www.eiae.org.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

WARNING:

THIS APPARATUS MUST BE EARTHED.

CAUTION:

To reduce the risk of electric shock, do not remove
cover. Refer servicing to qualified service personnel.

This projector is equipped with a 3-blade grounding
type plug to satisfy FCC rule. If you are unable to insert
the plug into the outlet, contact your electrician.

FCC INFORMATION (U.S.A. only)

CAUTION:

Changes or modification not approved by JVC could
void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply
with the limits for Class B digital devices, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encourage to try to correct the interference by
one or more of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and

receiver.

● Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.

● Consult the dealer or an experienced radio/TV
technician for help.

MACHINE NOISE INFORMATION (Germany only)

Changes Machine Noise Information Ordinance 3.
GSGV, January 18, 1991: The sound pressure level at
the operator position is equal or less than 70 dB (A)
according to ISO 7779.

About the installation place

Do not install the projector in a place that cannot support
its weight securely.

If the installation place is not sturdy enough, the projector
could fall or overturn, possibly causing personal injury.

IMPORTANT SAFEGUARDS

Electrical energy can perform many useful functions. This
unit has been engineered and manufactured to assure
your personal safety. But IMPROPER USE CAN RESULT
IN POTENTIAL ELECTRICAL SHOCK OR FIRE
HAZARD. In order not to defeat the safeguards
incorporated into this product, observe the following basic
rules for its installation, use and service. Please read
these Important Safeguards carefully before use.

- All the safety and operating instructions should be read
before the product is operated.

- The safety and operating instructions should be retained
for future reference.

- All warnings on the product and in the operating
instructions should be adhered to.

- All operating instructions should be followed.

- Place the projector near a wall outlet where the plug can

be easily unplugged.

- Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.

- Do not use attachments not recommended by the product
manufacturer as they may be hazardous.

- Do not use this product near water. Do not use
immediately after moving from a low temperature to high
temperature, as this causes condensation, which may
result in fire, electric shock, or other hazards.

- Do not place this product on an unstable cart, stand, or
table. The product may fall, causing serious injury to a
child or adult, and serious damage to the product. The
product should be mounted according to the
manufacturer’s instructions, and should use a mount
recommended by the manufacturer.

- When the product is used on a cart,
care should be taken to avoid quick
stops, excessive force, and uneven
surfaces which may cause the product
and cart to overturn, damaging
equipment or causing possible injury to
the operator.

2

ENGLISH

Getting Started Preparation Basic Operation Settings Troubleshooting Others

- Slots and openings in the cabinet are provided for
ventilation. These ensure reliable operation of the product
and protect it from overheating. These openings must not
be blocked or covered. (The openings should never be
blocked by placing the product on bed, sofa, rug, or similar
surface. It should not be placed in a built-in installation
such as a bookcase or rack unless proper ventilation is
provided and the manufacturer’s instructions have been
adhered to.)

- To allow better heat dissipation, keep a clearance between
this unit and its surrounding as shown below. When this
unit is enclosed in a space of dimensions as shown below,
use an air-conditioner so that the internal and external
temperatures are the same.

150 mm and above

300 mm

and above

300 mm
and above

150 mm

and above

200 mm
and above

- This product should be operated only with the type of
power source indicated on the label. If you are not sure of
the type of power supply to your home, consult your
product dealer or local power company.

- This product is equipped with a three-wire plug. This plug
will fit only into a grounded power outlet. If you are unable
to insert the plug into the outlet, contact your electrician to
install the proper outlet. Do not defeat the safety purpose
of the grounded plug.

- Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them. Pay particular attention to cords at doors,
plugs, receptacles, and the point where they exit from the
product.

- For added protection of this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage to
the product due to lightning and power line surges.

- Do not overload wall outlets, extension cords, or
convenience receptacles on other equipment as this can
result in a risk of fire or electric shock.

- Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.

- Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous
voltages and other hazards. Refer all service to qualified
service personnel.

-

Unplug this product from the wall outlet and refer service to
qualified service personnel under the following conditions:

a) When the power supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen on the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the

operating instructions. Adjust only those controls that are
covered by the Operation Manual, as an improper adjustment
of controls may result in damage and will often require
extensive work by a qualified technician to restore the product
to normal operation.

e) If the product has been dropped or damaged in any way.

f) When the product exhibits a distinct change in performance -

this indicates a need for service.

- When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or with same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.

-

Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condition.

- The product should be placed more than one foot away
from heat sources such as radiators, heat registers,
stoves, and other products (including amplifiers) that
produce heat.

- When connecting other products such as VCR’s, and DVD
players, you should turn off the power of this product for
protection against electric shock.

- Do not place combustibles behind the cooling fan. For
example, cloth, paper, matches, aerosol cans or gas
lighters that present special hazards when over heated.

- Do not look into the projection lens while the illumination
lamp is turned on. Exposure of your eyes to the strong
light can result in impaired eyesight.

- Do not look into the inside of this unit through vents
(ventilation holes), etc. Do not look at the illumination lamp
directly by opening the cabinet while the illumination lamp
is turned on. The illumination lamp also contains ultraviolet
rays and the light is so powerful that your eyesight can be
impaired.

- Do not drop, hit, or damage the light-source lamp (lamp
unit) in any way. It may cause the light-source lamp to
break and lead to injuries. Do not use a damaged light
source lamp. If the light-source lamp is broken, ask your
dealer to repair it. Fragments from a broken light-source
lamp may cause injuries.

- The light-source lamp used in this projector is a high
pressure mercury lamp. Be careful when disposing of the
lightsource lamp. If anything is unclear, please consult
your dealer.

- Do not ceiling-mount the projector to a place which tends
to vibrate; otherwise, the attaching fixture of the projector
could be broken by the vibration, possibly causing it to fall
or overturn, which could lead to personal injury.

- Use only the accessory cord designed for this product to
prevent shock.

*DO NOT allow any unqualified person to install the

unit.

Be sure to ask your dealer to install the unit (e.g.
attaching it to the ceiling) since special technical
knowledge and skills are required for installation. If
installation is performed by an unqualified person, it
may cause personal injury or electrical shock.

3

1

Getting Started

Safety Precautions (Continued)

POWER CONNECTION

For USA and Canada only

Use only the following power cord.

Power cord

WARNING:

THIS APPARATUS MUST BE EARTHED.

For Europe only

Use a certified main cord set complying with the
national regulations of the countries and the rated

voltage min. 200V, and min. dia. 0.75mm
that the power cord plug is the correct type for the AC
outlet in your country.
Consult your product dealer.

². Also ensure

4

ENGLISH

Dear Customer,

This apparatus is in conformance with the valid European directives and standards regarding electromagnetic
compatibility and electrical safety.

European representative of Victor Company of Japan, Limited is:
JVC Technology Centre Europe GmbH
Postfach 10 05 52
61145 Friedberg
Germany

Getting Started Preparation Basic Operation Settings Troubleshooting Others

5

Main Features

.

Supports Multiple Digital
Devices

...............................................

z Comes with a dual HDMI terminal that

allows digital transmission of high
definition signals. (pP14)

6

.

Beautiful Images on Big Screen

.................................................................

z Enjoy smooth and high resolution video images with no

visible grid, brought about by full high definition resolution
of 1920 c 1080 pixels. (pP20)

Getting Started Preparation Basic Operation Settings Troubleshooting Others

Perfect for Any Location

........................................................

z Comes with an 80 % vertical and 34 % horizontal

lens shift function. (pP18)

7

1

.

.

.

.

.

.

Getting Started

Contents

Getting Started

..................................................

Safety Precautions................................................2

Main Features .....................................................6

Contents..............................................................8

How to Read this Manual/

Accessories/Optional Accessories.......................9

About this Manual...........................................................9

Check the Accessories......................................................9

Optional Accessories.......................................................9

Controls and Features ........................................10

How to Use the Remote Control...........................13

Loading Batteries...........................................................13

Effective Range of Remote Control Unit............................13

Preparation

..................................................

Selecting Connecting Devices..............................14

Connecting........................................................15

Connecting via Video Cable and S-video Cable...............15

Connecting via Component Video Cable .........................15

Connecting via HDMI Cable...........................................16

Connecting via HDMI-DVI Conversion Cable ...................16

Connecting via SCART-RCA Cable..................................17

Connecting via RGB Video Cable ...................................17

Troubleshooting

..................................................

Troubleshooting.................................................36

What to Do When These Messages

Are Displayed .................................................38

About Warning Indicators..................................39

Actions to Be Taken for Warning Mode .......................... 39

Replacing the Lamp ...........................................40

Procedure for Lamp Replacement ...................................40

Resetting Lamp Time...................................................... 42

Cleaning and Replacing the Filter........................43

Others

..................................................

RS-232C Interface .............................................44

RS-232C Specifications ................................................. 44

Command Format ......................................................... 44

RS-232C Communication Examples................................ 48

Copyright and Caution.......................................50

About Trademarks and Copyright .................................. 50

Caution........................................................................50

Mounting this Unit......................................................... 51

Specifications ....................................................52

Dimensions................................................................... 53

Installing the Projector and Screen.......................18

Screen Size and Projection Distance................................19

Basic Operation

..................................................

Projecting Image................................................20

Convenient Features during Projection.................22

Setting the Screen Size...................................................22

Masking the Surrounding Area of an Image ....................22

Settings

..................................................

Setting Menu .....................................................24

Procedures for Menu Operation .....................................24

Setting Menu.................................................................25

Customizing Projected Images ............................34

Changing the Default Image Profile Values......................34

Registering User-defined Image Profiles...........................35

Registering User-defined Image Profiles from the Menu ....35

8

ENGLISH

How to Read this Manual/ Accessories/Optional Accessories

About this Manual

Getting Started Preparation Basic Operation Settings Troubleshooting Others

N

C

USER

1

COLOR

+

COLOR

-

CONTRAST

USER

SHARP

SHARP

D

USER

2

3

GAMMA

+

COLOR

-

TEMP

BRIGHT

INFO

HIDE

MENU

EXIT

ENTER

LIGHTTEST

Buttons to be used are colored in a
darker shade.

This manual mainly describes the operating method using the remote
control.

Buttons on the remote control are described as [Button Name].

z
z Selection items on the menu are described as “Selection Item”.

 Conventions in this manual

Describes the limitations of the functions or usage.

Indicates good-to-know information.

Describes operational precautions.

pP9

Indicates related pages.

Check the Accessories

N

O

.

.
..
.
.

.
.

E

AT

R

PE

O

P

.

M

.

..

O

.

.

C

.
.

T

F

C

F

O

C

E
P

MI

2

S

I

A

A

M

N

D

H

DY

D

O

E
D
I

AL

R

V

1

-

E

R

I

S

U

M

3

US

D

AT

H

N

A

N

M

O

M

E

A

D

I

G

R

V

E

R

EMA

2

US

O

N
I

C

P

L

M

E

CO

P

T

C

R
A

H

+

S

I

R
E

R

P

B

1

US

AR

-

SH
R
O

L

+

CO

O
F
N

R

I

T

O

S

L

A

-

CO

R
T

N

CO

Remote Control

T

H

G

IT
X
E

E
D
I

H

T

R

H

E

IG

U

L

T

N

N

E

M

E

T

S
E
T

AAA size Batteries

(for operation confirmation)

z Instruction manual, warranty card and other printed material are also included.

Optional Accessories

Please check with your authorized dealer for details.

Replacement Lamp: BHL5009-S (Lamp Unit)

z
z Replacement Filter: LC32058-002A (Inner Filter)

Power Cord

9

1

Getting Started

Controls and Features

z This unit comes with buffer material that cushions the lens. Remove the buffer

material before use.

z Do not throw away the buffer material, retain for future use. (pP50)

To adjust the focus.
To adjust the size of the image.

z Operate using the remote control. (pP20)

CAUTION

z Do not turn the lens with your hands.

 Front Side/Left Side

Lamp Cover (pP40)

Remote Sensor
(pP13)

Air Inlets

Lens Cap

Exhaust Vent

Rear Side/Top Surface

10

Remote Sensor (pP13)

To connect the power cord (pP20)

ENGLISH

Getting Started Preparation Basic Operation Settings Troubleshooting Others

Light on (Red):

Standby mode

Light on (Green):

During projection

Blinking (Green):

Image is temporarily hidden
(pP21)

Blinking (Red):

Cool Down mode (pP21)

To switch input

To display the menu

(pP20)

(pP24)

STANDBY/ON

MENU

WARNING

LAMP

STANDBY/ON

INPUT

HIDE

ENTER

Light on (Red):

Warning mode (pP39)

Light on/Blinking (Orange):

Lamp warning (pP39)

To turn on/off the power

To hide the image temporarily (pP21)

EXIT

To return to the previous menu

To select or confirm

Bottom Surface

Feet: The height (0 to 5 mm) can be adjusted by turning the foot.

Air Inlets/Filter (pP43)

To adjust the position of the image (pP19)

11

1

Getting Started

Controls and Features (Continued)

 Remote Control

To turn off the power

Select input mode (pP20)

To switch image profile

(pP34)

To adjust color density

(pP34)

To adjust contrast

(pP34)

To display information

........ ........

OFF

COLOR

COLOR

CONTRAST

MENU

OPERATE

HDMI 1 COMP.

C

USER

1

+

-

HDMI 2

S-VIDEOVIDEO ASPECT

NATURALCINEMA DYNAMIC

N

USER

2

SHARP

+

SHARP

-

BRIGHT

INFO

HIDE

ON

D

USER

3

GAMMA

COLOR

TEMP

EXIT

To turn on the power

To set the screen size
(pP22)

To set gamma
(pP34)

To adjust the outline of the image
(pP34)

To set color temperature
(pP34)

To adjust brightness
(pP34)

To hide the image temporarily
(pP21)

12

To display the menu

(pP24)

To display test patterns

For adjusting the image size

(zoom) and the focus. (pP20)

ENTER

PROJECTOR

To return to the previous menu

LIGHTTEST

To illuminate buttons on the remote control

To select or confirm

ENGLISH

How to Use the Remote Control

Loading Batteries

12 3

z If the remote control has to be brought closer to the projector to operate, it means that the batteries are wearing out. When this

happens, replace the batteries. Insert the batteries according to the +- marks.

z Be sure to insert the - end first.
z If an error occurs when using the remote control, remove the batteries and wait for 5 minutes. Load the batteries again and

operate the remote control.

Getting Started Preparation Basic Operation Settings Troubleshooting Others

Effective Range of Remote Control Unit

 When directing the remote control

toward this unit

When aiming the remote control towards the

z

remote sensor on this unit, ensure that the
distance to the sensor in front or at the rear of
this unit is within 7 m.

z If the remote control fails to work properly,

move closer to this unit.

 When reflecting off a screen

Ensure that total of distance A between this

z

unit and screen and distance B between
remote control and screen is within 7 m.

z As the efficiency of signals reflected from the

remote control unit differ with the type of
screen used, operable distance may
decrease.

Screen

This unit

30°

30°

30°

30°

30°

30°

30°

20°

20°

20°

N

O

.

.....

..

E
T
A

20°

20°

20°

R

E
P
O

.

MP

..

O

...

C

..

T

F

C

F

C

E

I

O

P

M

2

S

I

A

A

M

N

D

Y

H

D

D

O

E

L

D
I

A

R

V

1

-

E

R

S

S

U

MI

3

U

T

D

A

H

N

A

N

M

O

M

E

A

D
I

G

A

R

V

E

M

S

R

E

2

U

O

P

N

L

I

M

O

C

E

C

P

T

C

R

T

A

H

H

+

S

G
I

R
E

R

S

P

B

1

U

R
A
H

­S

R
O
L

O

+

C

O
F
N

R

I

T

O

S

L

A

O

­T

C

R

I
X

T

E

E

ON

D
I

C

H

T

R

H

G

E

I

U

L

N

NT

E
M

E

T

S
E
T

Remote Control

30°

30°

30°

30°

This unit

20°

20°

A

A

20°

20°

B

B

ON

...
.
.
..

E

T
RA
E

P
O

..

..
..
..
.

F

F
O

P

M
O
C

2
I
M
D

H
1
I

M
D

T

H

C

ASPE

C

I

EO

M

D

A

I

V

N
Y

S-

D

L

A

EO

R

D
I

U

V

T
A

D

N
A
M

INE

C

N

R
E
S

C

U

3

R

E
S
U

2

R
E
S

A

U

M

M

1

A

G
P
R
A

H
S

+

R
O
L

R

O

O

L

C

O
C

P

+

M
E

T
P
R

A
H
S

T

-

H
G
I
R

R

B

O
L
O

C

-

T
S

A
R
T
N

O
F

O

N
I

C

E
D
I
H

T
I
X
E

U

N
E
M

R
E

NT

E

T

H
G
I
L

T
S
E
T

Remote Control

13

2

C

O

M

PONEN

T

Preparation

Selecting Connecting Devices

z Do not turn on the power until connection is complete.
z The connection procedures differ according to the device used. For details, refer to the instruction manual of the device to be

connected.

z For audio output, connect the device to an amplifier.
z The images may not be displayed depending on the devices and cables to be connected.

Use an HDMI compliant cable (sold separately) with the HDMI logo.

z It may not be possible to connect to this unit depending on the dimension of the connector cover of the cables to be

connected.

DVD Recorder DVD Player

To connect via HDMI terminal (pP16)

To connect RS-232C terminal

To connect via component video terminals (pP15)

HDMI 2 HDMI 1 RS-232C

S-VIDEO

VIDEO

Y CB/PB CR/PR

GBR

SYNC

COMPONENT

To connect via video terminal (pP15)

To connect via S-video terminal (pP15)

Notebook PC

VCR and camcorder

14

Connecting

S-3

C

M

PONEN

T

C

B

/

P

BCR

/

P

R

G

B

R

S

VID

E

O

S3C

VID

E

O

S

Y

N

C

Connecting via Video Cable and S-video Cable

This unit

ENGLISH

Getting Started Preparation Basic Operation Settings Troubleshooting Others

To video input terminal

HD RS-232C

S-VIDEO

VIDEO

SYNC

OMPONENT

Y CB/PBCR/P

Y

GBR

Video cable (sold separately)

R

S-video cable (sold separately)

To S-video input terminal

Connecting via Component Video Cable

Video output

VCR and camcorder

S-video output

This unit

HD RS-232C

S-VIDEO

VIDEO

Y CB/PB CR/PR

SYNC

GBR

OMPONENT

Component video cable

(sold separately)

To component video input terminals

z Set “COMP” in the setting menu to “Y Pb/Cb Pr/Cr”. (pP28 - Q)

DVD player

Component video output terminals

(Red)

C

R/PR

CB/PB(Blue)

Y (Green)

15

2

S

O

RS232

C

COO

O

S

C

C/C

/

G

S

O

RS232

C

COO

O

S

C

C/C

/

G

Preparation

Connecting (Continued)

Connecting via HDMI Cable

This unit

HDMI 2 HDMI 1 RS-232C

S-VIDEO

VIDEO

Y CB/PB CR/PR

SYNC

GBR

COMPONENT

HDMI cable (sold separately)

To HDMI 1 or HDMI 2

input terminal

Connecting via HDMI-DVI Conversion Cable

DVD recorder

HDMI output terminal

This unit

MDMI 2 MDMI1 RS-232C

S-VIDEO

To HDMI 1 or HDMI 2

input terminal

COMPONENT

VIDEO

Y CB/PB CR/PR

SYNC

GBR

HDMI-DVI conversion cable (sold separately)

Notebook PC

DVI output terminal

16

Connecting via SCART-RCA Cable

S

VID

E

O

S3C

S

VID

E

O

S3C

VID

E

O

S

Y

N

C

This unit

ENGLISH

Getting Started Preparation Basic Operation Settings Troubleshooting Others

HD RS-232C

S-VIDEO

-

VIDEO

Y CB/PB CR/PR

GBR

SYNC

OMPONENT

SCART-RCA cable

(sold separately)

To RGB video and sync signal input terminals

z Set “COMP” in the setting menu to “SCART”. (pP28 - Q)

Connecting via RGB Video Cable

This unit

DVD player for European market

SCART terminal

HD RS-232C

S-VIDEO

-

VIDEO

Y CB/PB CR/PR

SYNC

GBR

OMPONENT

Device equipped with RGB output

RGB video output terminals

RGB video cable

R (Red)

(sold separately)

B (Blue)

To RGB video input terminals

G (Green) (Includes sync signal)

z Set “COMP” in the setting menu to “RGB”. (pP28 - Q)
z For information on compatible input signals, see “Specifications”. (pP52)

17

2

Preparation

Installing the Projector and Screen

Install this unit and the screen. Place this unit and the screen perpendicular to each other.
Failing to do so may give rise to trapezoidal distortion of the projected image.

A Install the projector and screen

 Left/Right position

*0 % up/down position (center)

Approximately 34 % (maximum) of the projected image
(Turn the dial to the right for maximum)

Approximately 34 % (maximum) of the projected image
(Turn the dial to the left for maximum)

 Up/Down position

*0 % left/right position (center)

Approximately 80 % (maximum) of the projected image
(Turn the dial to the left for maximum)

Approximately 80 % (maximum) of the projected image
(Turn the dial to the right for maximum)

18

 Shifting range of projected image

80%

34% 34%

80%

MDMI2 MDMI 1 RS-232C

COMPONENT

S-VIDEO

VIDEO

Y CB/PBCR/P

R

SYNC

GBR

ENGLISH

B Adjust such that the projected image is in the center of the screen

Getting Started Preparation Basic Operation Settings Troubleshooting Others

Moves the image to the
left or right

Moves the image up or
down

TIPS

z Adjustment can be done easily by moving the image

upwards towards the center.

z It may be necessary to set “Pixel Adjust” in the setting menu after adjusting the image position. (pP27 - J)

Screen Size and Projection Distance

Determine the distance from the lens to the screen to achieve your desired screen size.
This unit uses a 2.0x power zoom lens for projection.

 Relationship Between Projection Screen Size and Projection Distance

Projection Screen

Size
(Diagonal Length)
Aspect Ratio 16:9

60"

(Approx. 1.52 m)

Approximate Projection Distance

W (Wide) to T (Tele)

Approx.

1.78 m

to

Approx.

3.63 m

Projection Screen

Size
(Diagonal Length)
Aspect Ratio 16:9

140"

(Approx. 3.56 m)

Approximate Projection Distance

W (Wide) to T (Tele)

Approx.

4.24 m

to

Approx.

8.54 m

70"

(Approx. 1.78 m)

80"

(Approx. 2.03 m)

90"

(Approx. 2.29 m)

100"

(Approx. 2.54 m)

110"

(Approx. 2.79 m)

120"

(Approx.3.05 m)

130"

(Approx. 3.30 m)

z

The projection distances in the table are provided only as a guide. Use them as a reference during installation.

Approx.

2.09 m

Approx.

2.40 m

Approx.

2.71 m

Approx.

3.01 m

Approx.

3.32 m

Approx.

3.63 m

Approx.

3.93 m

to

to

to

to

to

to

to

Approx.

4.24 m

Approx.

4.86 m

Approx.

5.47 m

Approx.

6.08 m

Approx.

6.70 m

Approx.

7.31 m

Approx.

7.93 m

150"

(Approx. 3.81 m)

160"

(Approx. 4.06 m)

170"

(Approx. 4.32 m)

180"

(Approx. 4.57 m)

190"

(Approx. 4.83 m)

200"

(Approx. 5.08 m)

Approx.

4.55 m

Approx.

4.86 m

Approx.

5.16 m

Approx.

5.47 m

Approx.

5.78 m

Approx.

6.08 m

z To adjust the installation, use a projected image of aspect ratio 16:9.

to

to

to

to

to

to

Approx.

9.16 m

Approx.

9.77 m

Approx.

10.38 m

Approx.

11.00 m

Approx.

11.61 m

Approx.

12.23 m

19

3

.

Basic Operation

Projecting Image

This section describes the basic operations to project input images on the screen.

Preparation

......................................................................

........ ........

OFF

OPERATE

HDMI 1 COMP.

HDMI 2

S-VIDEOVIDEO ASPECT

NATURALCINEMA DYNAMIC

N

C

USER

USER

2

1

USER

ON

D

3

z Remove the lens cap.

A Insert the power plug to the power outlet

A Connect to this unit
B Connect to the power outlet

A

Power Cord
(Supplied)

B

STANDBY/ON

Light on (Red)

COLOR

+

COLOR

-

CONTRAST

MENU

PROJECTOR

SHARP

+

SHARP

-

INFO

HIDE

ENTER

GAMMA

COLOR

BRIGHT

TEMP

EXIT

LIGHTTEST

B Turn on the power

ON

STANDBY/ON

z You can also press the [STANDBY/ON] button on the unit to turn on the

power. (pP11)

C Project the image

a Select input mode

COMP.HDMI 2HDMI 1

VIDEO S-VIDEO

z You can also select the input mode by pressing the [INPUT] button on

the unit. (pP11)

b Play back the selected device

Light on (Green)

20

WARNING

LAMP

STANDBY/ON

D Adjust the position of the projection screen

z See “Installing the Projector and Screen” for procedures on adjusting the

position. (pP18)

E Adjust the image size (zoom) and the focus

a Display the test pattern (crosshatch)

TEST

Press repeatedly

b Adjust the focus

ENGLISH

Getting Started Preparation Basic Operation Settings Troubleshooting Others

Press for 1 second
or more

c Adjust the image size (zoom)

ENTER

z Switches between “Focus” and “Zoom” whenever the [ENTER] button is

pressed.

d To end

EXIT

F Turn off the power

While a confirmation screen is displayed

STANDBY/ON

Cool Down mode

STANDBY/ON

z The power cannot be turned off within approximately 90 seconds after it

has been turned on. Start operation only after 90 seconds time.

z You can also press the [STANDBY/ON] button on the unit to turn off the

power. (pP11)

z Put back the lens cap after use to prevent the lens from dirt.
z Pull out the power plug when the unit will not be used for a prolonged time.

Focus

Zoom

OFF

OFF

ENTER

Adjust accordingly by
pressing the up down buttons

ENTER

Adjust accordingly by
pressing the up down buttons

Blinking (Red)

Light on (Red)

TIPS

You can hide the image
temporarily

...............................

You can hide the image temporarily.

HIDE

STANDBY/ON

Green light blinks when

the image is hidden

z Press the [HIDE] button again to

display image.

z The power cannot be turned off

when the image is temporarily
hidden.

MEMO

About Cool Down mode

...............................

z

The Cool Down mode is a function
to cool down the lamp for
approximately 60 seconds after
projection is complete.
This function prevents the internal
parts of the unit from deformation
or damage due to overheating of
the lamp. It also prevents lamp
blowout and premature shortening
of lamp life.

z During Cool Down mode, the

[STANDBY/ON] indicator blinks in
red.

z After the Cool Down mode is

complete, the unit automatically
returns to standby mode.

z Do not pull out the power plug

during Cool Down mode. This may
shorten the lamp life and cause a
malfunction.

21

3

Basic Operation

Convenient Features during Projection

You can change the screen size of the projected image or hide the surrounding area of an image for which
quality at the outer area has deteriorated.

Setting the Screen Size

The projected image can be set to a most appropriate screen size (aspect

........ ........

OFF

OPERATE

ON

ratio).

HDMI 1 COMP.

HDMI 2

S-VIDEOVIDEO ASPECT

NATURALCINEMA DYNAMIC

N

C

USER

COLOR

COLOR

CONTRAST

MENU

USER

2

1

SHARP

+

+

SHARP

-

-

BRIGHT

INFO

HIDE

ENTER

D

USER

3

GAMMA

COLOR

TEMP

EXIT

LIGHTTEST

ASPECT

The screen size can also be set from “Aspect” of the setting menu. (pP29 - S)

z

4:3 16:9 ZOOM

z When high definition images are input, the “V-Stretch” setting will be available

instead. (pP29 - T)

z When PC signals are input, the “Resize” setting will be available instead.

(pP29 - U)

 Input Image and Projected Image by Different Screen Size Settings

Input Image

SDTV(4:3)

4:3 16:9 Zoom

Aspect Ratio: Same

Most appropriate
screen size

Screen Size

Aspect Ratio:
Landscape

Image is stretched
horizontally

Aspect Ratio: Same
Top and bottom of the

image are missing

PROJECTOR

SDTV(4:3)
Image recorded in
landscape (black
bands on top and

Aspect Ratio: Same
Small image is
projected

Aspect Ratio:
Landscape
Image is stretched
horizontally

Aspect Ratio: Same

Most appropriate
screen size

bottom) of DVD
software

Depending on the input image, selecting “4:3” may result in a vertically stretched

z

image while selecting “16:9” provides you with the most appropriate screen size.

Masking the Surrounding Area of an Image

Images for which quality at the outer area has deteriorated can be projected
by masking (hiding) the surrounding area of the projected image.

A Project the image

iImage for which quality at the outer

area has deteriorated.

22

B Mask the image

ENGLISH

Getting Started Preparation Basic Operation Settings Troubleshooting Others

a Display the setting menu

MENU

b Select “Setup” g “Mask”

ASELECT

ENTER

BCONFIRM

c Set a mask value

ASELECT

ENTER

BCONFIRM

Setup

Image

Image Adjust

Color Temp.

Gamma

Offset

Pixel Adjust

Image Profile

Profile Memory

Picture Position

HDMI Input Level

Mask

Overscan

Image Profile

Profile Memory

Picture Position

HDMI Input Level

Mask

Overscan

Source Install. Func. Info.

SetupImage Source Install. Func. Info.

2.5%

5%

Off

SetupImage Source Install. Func. Info.

2.5%

5%

Off

MEMO

z Masking is available only when high

definition images are input.

Example:

When the “Mask” value is changed
from “Off” g “5%”

C To end

MENU

23

4

Settings

Setting Menu

Projected images can be adjusted to a desired view by changing the default settings.

Procedures for Menu Operation

Example:

........ ........

OFF

OPERATE

HDMI 1 COMP.

HDMI 2

ON

When changing “Aspect” from “4:3” to “16:9”

A Display the setting menu

Image

Setup

Source Install. Func. Info.

C

USER

1

COLOR

+

COLOR

-

CONTRAST

MENU

S-VIDEOVIDEO ASPECT

NATURALCINEMA DYNAMIC

N

D

USER

USER

2

3

SHARP

GAMMA

+

SHARP

ENTER

INFO

HIDE

COLOR

-

TEMP

BRIGHT

EXIT

LIGHTTEST

Image Adjust

MENU

Color Temp.

Gamma

Offset

Pixel Adjust

B Select “Source” g “Aspect”

ASELECT

ENTER

BCONFIRM

Image

COMP

HDMI

Aspect

Film Mode

Color System

Black Level

C Set to “16:9”

ASELECT

ENTER

BCONFIRM

Image

COMP

HDMI

Aspect

Film Mode

Color System

Black Level

Setup

Source Install. Func. Info.

4:3

16:9

Zoom

Setup

Source Install. Func. Info.

4:3

16:9

Zoom

24

PROJECTOR

D To end

MENU

Setting Menu

Item values shown in are factory settings.

z Items that can be configured differ according to the input signals.

Image > Image Adjust

A Contrast

Adjusts the contrast of the projected image.

(Black) b50 to 50 (White)

B Brightness

Adjusts the brightness of the projected image.

(Darken) b30 to 30 (Brighten)

C Color

Adjusts the color density of the projected image.

(Lighten) b50 to 50 (Darken)

D Tint

Adjusts the hue of the projected image.

(Red) b30 to 30 (Green)

E Sharpness

Adjusts the outline of the projected image.

(Soft) b30 to 30 (Sharp)

F DNR

Adjusts the strength of noise removal of the projected image.

(Weak) 0 to 30 (Strong)

ENGLISH

Getting Started Preparation Basic Operation Settings Troubleshooting Others

z “Contrast”, “Brightness”, “Color” and “Sharpness” can also be configured from the remote control. (pP12)
z “Tint” can only be adjusted when NTSC signals are input to the video or S-video input terminal.

Image > Color Temp.

G Color Temp.

Sets the color temperature of the projected image.

Low Select this to give a reddish tinge to the image.
Middle Select this to have a balanced image.
High Select this to give a bluish tinge to the image.

Red (Less red) b255 to 0 (More red)

Memory10

Memory20

* The red, green and blue colors can be adjusted and registered respectively.

Green (Less green) b255 to 0 (More green)
Blue (Less blue) b255 to 0 (More blue)
Red (Less red) b255 to 0 (More red)
Green (Less green) b255 to 0 (More green)
Blue (Less blue) b255 to 0 (More blue)

z This setting can also be configured from the remote control. (pP12)

25

4

Settings

Setting Menu (Continued)

Image > Gamma

H Gamma

Sets the gradation characteristics of the projected image.

Normal For normal circumstances, select this setting.
Theater1 Sets gamma to “Theater1”.
Theater2 Sets gamma to “Theater2”.
Dynamic Select this when in well-lighted areas (such as living room) or when playing games.

Custom
(Gamma Setup)

z

“Normal” is suitable for normal circumstances but other settings can be selected according to your preferences.

z This setting can also be configured from the remote control. (pP12)

*“Gamma Adjust”

A Select the reference gamma curve coefficient (1.8 to 2.6) in “Correction Value”.
B Select the color to be adjusted in the gamma adjustment screen.

The gamma can be set according to your preferences.
Correction Value The coefficient (1.8 to 2.6) of the gamma curve can be selected.

The gamma curve for the colors (R, G, B) can be adjusted

Gamma Adjust *

separately.
Adjusting “W” will adjust for all “R, G, B” values. Gamma curves

are represented by a “G”.

Save Saves the adjusted gamma data.
Load Loads the gamma data that was saved.

All Reset

Returns the gamma coefficients to the values set by “Correction
Value”.

Correction Value W

Gamma Adjust R

Save G

Load B

All Reset

C Adjust the gamma curve in the gamma curve adjustment screen.

Correction Value

Gamma Adjust

Save

Load

All Reset

Adjustment Point (R)

X: 5 %
Y: 51

1023

512

0 50 100 (%)

Select the point where the gradation (brightness) is to
be adjusted with the H / I buttons.

D To end

EXIT

EXIT EXIT

Correction Value

Gamma Adjust

Save

Load

All Reset

Adjustment Poi nt (R)

X: 5 %
Y: 51

1023

512

0 50 100 (%)

Adjust the gradation (brightness) with the
J / K buttons.

Save gamma data?

Yes : Press [ENTER] button
No : Press [EXIT] button

ENTER

26

z If gamma curve is adjusted repeatedly, calculation errors will be accumulated and the gamma curve may not be able to

revert back to its original form. In that case, select the coefficient in “Correction Value” again or retrieve the previous gamma
data using “Load”.

ENGLISH

Image > Offset

I Offset

Adjusts the respective brightness of the red, green and blue colors in dark image areas. (Offset level)

Red (Less red) b60 to 60 (More red)
Green (Less green) b60 to 60 (More green)
Blue (Less blue) b60 to 60 (More blue)

Image > Pixel Adjust

J Pixel Adjust

Makes fine adjustments of 1 pixel unit for each minor color shift in the horizontal/vertical direction of the image.

Horiz. Red (Moves red to left) 1 to 7 (Moves red to right)
Horiz. Green (Moves green to left) 1 to 7 (Moves green to right)
Horiz. Blue (Moves blue to left) 1 to 7 (Moves blue to right)
Vert. Red (Moves red down) 1 to 5 (Moves red up)
Vert. Green (Moves green down) 1 to 5 (Moves green up)
Vert. Blue (Moves blue down) 1 to 5 (Moves blue up)

Getting Started Preparation Basic Operation Settings Troubleshooting Others

z The horizontal and vertical directions are reversed when the image is flipped to the left or right, or flipped up or down.
z To adjust, use still images with distinct outlines.
z As the adjustments are minor, the effect may be difficult to see for some images.

Setup > Image Profile

K Image Profile

Configures the image profile. (pP34)

Cinema Select this to view images with movie quality in a dark room.
Natural Select this to view projected images with quality as-is in a dark room.
Dynamic Select this to view images with clear quality in a bright room.
User1 Selects image profile registered in “User1”.
User2 Selects image profile registered in “User2”.
User3 Selects image profile registered in “User3”.

z This setting can also be configured from the remote control. (pP12)

Setup > Profile Memory

L Profile Memory

Registers or deletes image profiles.

Save User1 Registers image profile in “User1”.
Save User2 Registers image profile in “User2”.
Save User3 Registers image profile in “User3”.
Clear User1 Returns image profile in “User1” to factory setting (natural).
Clear User2 Returns image profile in “User2” to factory setting (natural).
Clear User3 Returns image profile in “User3” to factory setting (natural).
Reset Cinema Returns image profile in “Cinema” to factory setting.
Reset Natural Returns image profile in “Natural” to factory setting.
Reset Dynamic Returns image profile in “Dynamic” to factory setting.

z “Contrast”, “Brightness”, “Color”, “Sharpness”, “DNR”, “Color Temp.”, “Gamma” and “Offset” are registered in “Image Profile”.

27

4

Settings

Setting Menu (Continued)

Setup > Picture Position

M Picture Position

Adjusts the horizontal/vertical position of the projected image.

z

The display position value varies with the input signal.

z This adjustment is available for analog input signals, or for COMPONENT and HDMI-1/2 input signals when “V-Stretch” is set to

“On”.

Setup > HDMI Input Level

N HDMI Input Level

Configures the input level setting of the HDMI input terminal.

Standard For normal circumstances, select this setting.

Enhanced

z This setting is available only when projecting the HDMI input.

Select this setting when the black-and-white of the projected image is unclear when
RGB video signals are input from DVI devices.

Setup > Mask

O Mask

Masks (Hides) the outer area of the projected image.

2.5% Masks 2.5 % of the screen.
5% Masks 5 % of the screen.
Off No masking.

z Masking is available only when high definition images are input.

Setup > Overscan

P Overscan

Selects whether or not to set overscan for the 4:3 video signals (NTSC, PAL, SECAM, 480i, 576i, 480p and 576p).

Off No overscan.
On Overscans the top, left, bottom and right at 2.5 % each.

z This setting is not available when PC signals are input to HDMI terminal.

Source > COMP

Q COMP

Configures the input signals of the component video input terminals.

Y Pb/Cb Pr/Cr Select this when component video signals are input.
RGB Select this when RGB video signals are input.

SCART

Select this when RGB video signals and sync signals are input from SCART plug for
European market.

28

z This setting is available only when projecting the component video input.

Source > HDMI

R HDMI

Configures the input signals of the HDMI input terminal.

Auto Automatically configures input signals.
YCbCr(4:4:4) Select this when Y Cb Cr (4:4:4) video signals are input.
YCbCr(4:2:2) Select this when Y Cb Cr (4:2:2) video signals are input.
RGB Select this when RGB video signals are input.

z This setting is available only when projecting the HDMI input.

ENGLISH

Source > Aspect (When SD video signals are being input)

S Aspect

Configures the screen size (aspect ratio) of the projected image.

4:3 Sets screen size of the projected image to 4:3.
16:9 Sets screen size of the projected image to 16:9.
Zoom Zooms the image.

z This setting can also be configured from the remote control. (pP12, 22)

Source > V-Stretch (When HD video signals are being input)

T V-Stretch

When set to “On”, the projected 2.35:1 image will be stretched vertically to the panel resolution.

Off Projects the 2.35:1 image as-is. (Black bands will be displayed on the top and bottom.)
On The projected 2.35:1 image will be stretched vertically to the panel resolution.

Getting Started Preparation Basic Operation Settings Troubleshooting Others

“On”“Off”

Source > Resize (When PC signals are being input)

U Resize

Sets the screen size of the projected image.

Aspect

Panel Enlarges the PC signal horizontally/vertically, and displays it in 16:9 aspect ratio.

1:1

Enlarges the PC signal horizontally/vertically until it fits the panel height, and displays it
in the original aspect ratio.

Displays the PC signal corresponding to the panel at one dot per pixel ratio. The PC
screen can be shown in the original size.

“Panel”“Aspect” “1:1”

XGA(1024 x 768) XGA(1024 x 768) XGA(1024 x 768)

Source > Film Mode

V Film Mode

Select this to view movies shot on film.

Auto For normal circumstances, select this setting.
Off Select this when you are not watching movies shot on film.

z This setting is not available when PC signals are input to HDMI terminal.

29

4

Settings

Setting Menu (Continued)

Source > Color System

W Color System

Configures the color system.

Auto Configures the color system automatically.
NTSC Select this when the color system is NTSC.
NTSC4.43 Select this when the color system is NTSC4.43.
PAL Select this when the color system is PAL.
PAL-M Select this when the color system is PAL-M.
PAL-N Select this when the color system is PAL-N.
SECAM Select this when the color system is SECAM.

z

This setting is available only when projecting the video or S-video input.

Source > Black Level

X Black Level

Configures the black level.

0 %

7.5 % Select this when the dark portions of an image appear washed out with the 0 % setting.

Select this when the gradation of the dark portions of an image is indistinct with the

7.5 % setting.

z This setting can only be adjusted when NTSC signals are input to the video or S-video input terminal.

Install. > Menu Position

Y Menu Position

Sets the display position of the menu.

Upper left Displays menu on the upper left of the screen.
Upper center Displays menu on the upper center of the screen.
Upper right Displays menu on the upper right of the screen.
Left center Displays menu on the left center of the screen.
Center Displays menu on the center of the screen.
Right center Displays menu on the right center of the screen.
Lower left Displays menu on the lower left of the screen.
Lower center Displays menu on the lower center of the screen.
Lower right Displays menu on the lower right of the screen.

Install. > Menu Display

Z Menu Display

Sets the duration for displaying the menu.

15 sec Displays for 15 seconds.
On Always display.

30