JVC FS-SD550, FS-SD990, CA-FSSD550, SP-FSSD550, CA-FSSD770 Instructions Manual

...

Download

Page 1

COMPACT COMPONENT SYSTEM

FS-SD550/FS-SD770/FS-SD990

Consists of CA-FSSD550 and SP-FSSD550 Consists of CA-FSSD770 and SP-FSSD770 Consists of CA-FSSD990 and SP-FSSD990

REMOTE CONTROL DIMMER SLEEP

AUTO

DISPLAY FM MODE

PRESET

PROGRAM

REPEATRANDOM

DOOR

AHB PRO

SLIDE

BASS TREBLE CANCEL

SET

DOWN

FADE MUTING

MD/AUX FM / AM

VOLUME

FS-SD550

REMOTE CONTROL

DIMMER SLEEP

AUTO

DISPLAY FM MODE

PRESET

PROGRAM

REPEATRANDOM

DOOR

AHB PRO

SLIDE

BASS TREBLE CANCEL

SET

DOWN

FADE MUTING

MD/AUX FM / AM

VOLUME

FS-SD770, FS-SD990

INSTRUCTIONS

For Customer Use:

Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for f utur e reference.

Model No. Serial No.

GNT0008-010A

[A]

Page 2

Warnings, Cautions and Others

15 cm

IMPORTANT FOR LASER PRODUCTS

REPRODUCTION OF LABELS

1 CLASSIFICATION LABEL, PLACED ON EXTERIOR

SURFACE

CLASS 1 LASER PRODUCT

2 WARNING LABEL, PLACED INSIDE THE UNIT

1 CLASS 1 LASER PRODUCT 2

DANGER:

failed or defeated. Avoid direct exposure to beam.

CAUTION:

viceable parts inside the Unit; leave all servicing to qualified service personnel.

Caution — %%%% switch!

Disconnect the mains plug to shut the power off completely. The switch in any position does not disconnect the mains

line. The power can be remote controlled.

CAUTION

To reduce the risk of electrical shocks, fire, etc.: 1 Do not remove screws, covers or cabinet. 2 Do not expose this appliance to rain or moisture.

Invisible laser radiation when open and interlock

Do not open the top cover. There are no user ser-

Caution: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows: 1 Front: No obstructions and open spacing. 2 Sides/ Top/ Back:No obstructions should be placed in the

areas shown by the dimensions below.

3 Bottom: Place on the level surface. Maintain an

adequate air path for ventilation by placing on a stand with a height of 10 cm or more.

SAFETY PRECAUTIONS

Prevention of Electric Shocks, Fire Hazards and Damage 1 Even when the

button is set to STANDBY, a very small

current will flow. To save power and for safety when not using the unit for an extended period of time, disconnect

the power cord from the household AC outlet. 2 Do not handle the power cord with wet hands. 3 When unplugging from the wall outlet, always grasp and

pull the plug, not the power cord. 4 Consult your nearest dealer when damage, disconnection,

or contact failure affects the cord. 5 Do not bend the cord severely, or pull or twist it. 6 Do not modify the power cord in any manner. 7 To avoid accidents, do not remove screws to disassemble

the unit and do not touch anything inside the unit. 8 Do not insert any metallic objects into the unit. 9 Unplug the power cord when there is a possibility of lightning. 10 Do not use this apparatus in a bathroom or places with water.

Also do not place any containers filled with water or liquids

(such as cosmetics or medicines, flower vases, potted plants,

cups, etc.) on top of this apparatus. 11 Do not block the ventilation opcnings or holes. (If the venti-

lation openings or holes are blocked by a newspaper or

cloth, etc., the heat may not be able to get out.) 12 Do not place any naked flame sources, such as lighted

candles, on the apparatus. 13 When discarding batteries, environmental problems must

be considered and local rules or laws governing the dis-

posal of these batteries must be followed strictly.

Front view

15 cm

CAUTION

■■■■

About the Internal Cooling Fan

This unit includes an internal cooling fan, so as to allow for high-power operation within a small space. This fan comes on when the sound level is set high, and may also come on even at low sound levels if the internal tem perature rise s. To ensure effective fan operation, please leave at least 15cm clearance between the rear of the unit and the wall, and at least 1cm clearance on each side of

1 cm 1 cm

STANDBY/ON

OPEN/CLOSE

PHONES

15 cm

10 cm

Side view

G-1

Page 3

Introduction

Thank you for purchasing the JVC Compact Component System. We hope it will be a valued addition to your home, giving you years of enjoyment. Be sure to read this instruction manual carefully before operating your new stereo system. In it you will find all the information you need to set up and use the system. If you have a query that is not answered by the manual, please contact your dealer.

Features

Here are some of the things that make your System both powerful a nd simple to use.

■ The controls and operations have been redesigned to make them very easy to use, freeing you to

just enjoy the music.

• With JVC’s COMPU PLAY you can turn on the System and automatically start the Radio or

CD Player with a single touch.

■ The System incorporates Active Hyper Bass PRO circuitry to faithfully reproduce low frequency

sounds.

■ A 45-station preset capability (30 FM and 15 AM (MW/LW)) in addition to auto-seek and manual tuning.

■ CD options that include repeat, random and program play.

■ Timer functions; Daily Timer and Sleep Timer.

■ You can connect various external units, such as an MD recorder.

■ The system can play CD-R and CD-RW after they have been finalized.

■ You can play back your original CD-R or CD-RW recorded in Music CD format. (However t hey may not be playe d back

depending on their characteristics or recording conditions.)

How This Manual Is Organized

• Basic information that is the same for many different functions - e.g. setting th e volume - is given in the section ‘Basic Operations’, and not repeated under each function.

• The names of buttons/controls and display messages are written in all capital letters: e.g. FM/AM, “NO DISC”.

• System functions are written with an initial capital letter only: e.g. Normal Play.

Use the table of contents to look up specific information you requi re. We have enjoyed making this manual for you, and hope it serves yo u in enjoying the many features built into your System.

WARNINGS

• DO NOT PUT ANYTHING ON THE TOP COVER. IF THE SYSTEM IS OPERATED WITH SOMETHING PUT ON THE TOP COVER, IT WILL BE DAMAGED WHEN YOU TRY TO OPEN THE TOP COVER.

• NEVER REMOVE THE TOP COVER FROM THE UNIT. SERIOUS INJURY MAY OCCUR IF THE SYSTEM IS OPERATED WITHOUT THE TOP COVER.

IMPORTANT CAUTIONS

Installation of the System

• Select a place which is level, dry and neither too hot nor too cold. (Between 5°C and 35°C or 41°F and 95°F.)

• Leave sufficient distance between the System and a TV.

• Do not use the System in a place subject to vibrations.

Power cord

• Do not handle the power cord with wet hands!

• Some power is always consumed as long as the power cord is connected to the wall outlet.

• When unplugging the System from the wall outlet, always pull the plug, not the power cord.

Malfunctions, etc.

• There are no user serviceable parts inside. In case of system failure, unplug the power cord and consult your dealer.

• Do not insert any metallic object into the System.

• Do not insert your hand between the Top Cover and the main body when the Top Cover is being closed.

Page 4

Table of Contents

Introduction........................................................................................................1

Features ......................................................................................................................................1

How This Manual Is Organized.................................................................................................1

WARNINGS ..............................................................................................................................1

IMPORTANT CAUTIONS .......................................................................................................1

Getting Started...................................................................................................3

Accessories.................................................................................................................................3

How To Put Batteries In the Remote Control............................................................................3

Using the Remote Control..........................................................................................................3

Connecting the FM Antenna......................................................................................................4

Connecting the AM (MW/LW) Antenna...................................................................................5

Connecting the Speakers............................................................................................................6

Connecting a Subwoofer............................................................................................................7

Connecting External Equipment................................................................................................7

Connecting an MD Recorder, etc (Digital Output)...................................... ..............................7

Connecting the AC Power Cord.................................................................................................8

COMPU Play..............................................................................................................................8

Automatic Power On..................................................................................................................8

Basic Operations ....................................................................... ..... .... ...............9

Turning the Power On and Off...................................................................................................9

Adjusting the Brightness (DIMMER)........................................................................................9

Adjusting the Volume................................................................................................................ 9

Fade-out Muting (FADE MUTING)........................................................................................10

Reinforcing the Bass Sound (AHB PRO)................................................................................10

Tone Control (BASS/TREBLE)...............................................................................................10

Showing the Time (CLOCK/DISPLAY).................................................................................10

Sliding the Top Cover (DOOR SLIDE)...................................................................................10

Using the Tuner................................................................................................11

Tuning In a Station...................................................................................................................11

Presetting Stations....................................................................................................................12

Auto Presetting.........................................................................................................................12

To Change the FM Reception Mode........................................................................................12

Using the CD Player.........................................................................................13

To Insert a CD..........................................................................................................................13

To Unload a CD....................................................................................................................... 14

Basics of Using the CD Player-Normal Play...........................................................................14

Programming the Playing Order of the Tracks........................................................................14

Random Play............................................................................................................................15

Repeating Tracks......................................................................................................................15

Using External Equipments ............................................................................16

Listening to External Equipment..... .... ........................................................................ .............16

Recording the System’s Source to External Equipment ..........................................................16

Using the Timers..............................................................................................17

Setting the Clock............................. .... ........................................................................ .............17

Setting the Daily Timer................................................................................... .........................17

Setting the SLEEP Timer.........................................................................................................19

Care And Maintenance ................................................................... .... .............20

Troubleshooting...................... ..... .... .... ...................................... ..... .................21

Specifications.................. .... .... ....................................... .... ..............................22

Specifications....................................................................................Back cover

Page 5

Getting Started

Accessories

Make sure that you have all of the following items, which are supplied with the System.

Power Cord (1) AM Loop Antenna (1) Remote Control (1) Batteries (2) FM Wire Antenna (1) Speaker Cords (2)

If any of these items are missing, contact your dealer immediately.

How To Put Batteries In the Remote Control

Match the polarity (+ and –) on the batteries with the + and – markings in the battery compartment.

R6P(SUM-3)/AA(15F)

CAUTION:

• Handle batteries properly.

■ To avoid battery leakage or explosion:

• Remove batteries when the Remote Control will not be used for a long time.

• When you need to replace the batteries, replace both batteries at the same time with new ones.

• Do not use an old battery with a new one.

• Do not use different types of batteries together.

Using the Remote Control

The Remote Control makes it easy to use many of the functions of the System from a distance of up to 7m (23 feet) away. You need to point the Remote Control at the remote sensor on the System’s front panel.

STANDBY/ON

Remote sensor

OPEN/CLOSE

PHONES

Page 6

Getting Started

Getting StartedGetting Started

CAUTION:

• Make all connections before plugging the System into an AC power outlet.

Connecting the FM Antenna

Rear Panel of the Unit

SUB WOOFER

CD DIGITAL OUT

AM LOOP

OUT IN

ANTENNA

AM EXT FM(75

COAXIAL

AUX

)

Using the Supplied Wire Antenna

FM wire antenna (supplied)

Using the Coaxial Type Connector (Not Supplied)

A 75-ohm antenna with coaxial type connector (IEC or DIN45 325) should be connected to the FM 75-ohm COAXIAL terminal.

SPEAKERS IMPEDANCE 4 16

AC IN

• Before attaching a 75 ohm coaxial lead (the kind with a round wire going to an outdoor antenna), disconnect the supplied FM Wire Antenna.

If reception is poor, connect the outdoor antenna.

Coaxial cable

FM outdoor antenna (Not supplied)

Page 7

Connecting the AM (MW/LW) Antenna

ANTENNA

AM EXT FM(75

)

COAXIAL

AM LOOP

Rear Panel of the Unit

Getting Started

Getting StartedGetting Started

SUB WOOFER

CD DIGITAL OUT

AM LOOP

OUT IN

ANTENNA

AM EXT FM(75

COAXIAL

AUX

)

AM loop antenna (Supplied)

Attach the AM loop to its base by snapping the tabs on the loop into the slot in the base.

SPEAKERS IMPEDANCE 4 16

AC IN

Turn the loop until you have the best reception.

CAUTION:

• To avoid noise, keep antennas away from the System, the connecting cord and the AC power cord.

Page 8

Getting Started

Getting StartedGetting Started

CAUTION:

• Make all connections before plugging the System into an AC power outlet.

Connecting the Speakers

1. Open each of the terminals to connect the speaker wire leads.

2. Connect the speaker cords between the Speaker terminals of the Unit and the terminals of the Speakers. Connect the cords with a black line to the (–) terminals and cords without a black line to the (+) terminals.

3. Close each of the terminals to securely connect the cords.

Right side (rear view)

Marked with a black line

SPEAKERS IMPEDANCE 4 16

Left side (rear view)

• Since both speakers are the same, you can put either one to the right or left side.

CAUTION:

• A TV may display irregular colors if located near the speakers. If this happens, set the speakers away from the TV.

Removing the speaker grilles

The speaker grilles can be moved.

When removing:

1. Pull the top forwards you with your fingers.

2. Also pull the bottom towords you.

• When removing the speaker grille from the FSSD990’s speaker, be careful not to damage the cabinet.

When attaching the speaker grille:

(FS-SD550) (FS-SD770 and FS-SD990)

(FS-SD550)

Speaker grille

(FS-SD770 and FS-SD990)

Speaker grille

Page 9

Getting Started

Getting StartedGetting Started

Connecting a Subwoofer

Connect a signal cord (not supplied) between the System’s SUBWOOFER terminal and the input terminal of an external subwoofer.

SUB WOOFER

CD DIGITAL OUT

ANTENNA

AM EXT FM(75 11mm Max/

AM LOOP

OUT IN

AUX

Signal cord (not supplied)

11mm Max.

)

COAXIAL

Subwoofer (not supplied)

* Use the plug whose diameter is 11mm or less.

Connecting External Equipment

Connect signal cords (not supplied) between the Syste m’s MD/AUX -O UT/IN te rminals and th e output /in put termin als of t he external MD recorder, tape deck, etc. You can then listen to the external source through the System or record the System’s CD player or tuner to the external unit.

Signal cord (not supplied)

11mm Max.

SUB WOOFER

* Use the plug whose diameter is 11mm or less.

CD DIGITAL OUT

ANTENNA

AM EXT FM(75

AM LOOP

OUT IN

AUX

COAXIAL

Stereo mini-plug

Signal cord (not supplied)

)

11mm Max.

Stereo mini-plug

Pin-plug x 2

MD recorder or tape deck (not supplied)

Pin-plug x 2

Connecting an MD Recorder, etc (Digital Output)

Unplug the cap and connect an optical digital cord (not supplied) between the System’s CD DIGITAL OUT terminal and the input terminal of the MD recorder, etc. You can record the digital output signal from the System’s CD Player to the MD recorder, etc.

Cap

CD DIGITAL OUT

11mm Max.

MD recorder, etc. (not supplied)

Optical digital cord (not supplied)

* Use the plug whose diameter is 11mm or less.

Page 10

Getting Started

Getting StartedGetting Started

Connecting the AC Power Cord

Firmly insert the supplied AC power cord into the AC inlet on the back of the Unit.

AC IN

Power cord

CAUTIONS:

• ONLY USE THE JVC POWER CORD PROVIDED WITH THIS SYSTEM TO AVOID MALFUNCTION OR DAMAGE TO THE SYSTEM.

• BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN THE SYSTEM IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.

Now you can plug the AC power cord into the wall outlet, and your System is at your command!

COMPU Play

JVC’s COMPU PLAY feature lets you control the most frequently used System functions with a single touch. With One Touch Operation you can play a CD, turn on the radio, or listen to an external equipment with a single p ress o f the play button for that function. One To uch Ope ration tur ns the po wer on fo r you , then st arts the functio n you have sp ecified. A t the same time, the Top Cover moves backward to allow the Un it’s top button operation. If the System is not ready (no CD in place), the System still powers on so you can insert a CD. How One Touch Operation works in each case is explained in the section dealing with that function. The COMPU PLAY buttons are:

On the Remote Control

CD #/8 button FM/AM button MD/AUX button

Automatic Power On

The System automatically turns on with the following operation.

• When you press the CD 0 button on the Remote Control or the OPEN/CLOSE button on the Unit, the System automatically

turns on and the T op Co v er opens to allo w CD setting. Ho wever , this operation does not change the function to CD. When you press the % button to turn off the System, the Top Cov e r will be auto matically closed if it is opened.

• When you press the DOOR SLIDE button on the Remote Control, the System automatically turns on and the Top Cover

moves backwards to allo w b utton operation. When you press the % button to turn off the System, the Top Cover will automaticall y mo ves back to the original position, if it is in the backward position.

Page 11

Basic Operations

REMOTE CONTROL

DIMMER

DISPLAY

AHB PRO

BASS

FADE

MUTING

VOLUME+,–

Turning the Power On and Off

Turning the System On

Press the % button.

The Top Cover moves backward and the Unit’s top buttons appear. The display comes on and “HELLO” is displayed once. The STANDBY/ON indicator lights in green. The System comes on ready to continue in the mode it was in when the power was last turned off.

■For example, if the last thing you were doing was listening to a CD, you are now ready to listen to a CD again. If you wish, you can change to another source.

■If you were listening to the Tuner last, the Tuner comes on playing the station it was last set to.

DIMMER SLEEP

AUTO

DISPLAY FM MODE

PRESET

PROGRAM

DOOR

AHB PRO

SLIDE

BASS TREBLE CANCEL

SET

DOWN

FADE MUTING

MD/AUX FM / AM

VOLUME

REPEATRANDOM

DOOR SLIDE TREBLE

PRESET

TUNINGFM/AMMD/AUX

AHB PRO CLOCK TIMER VOLUME

AHB PRO

STANDBY/ON OPEN/CLOSE

MULTI CONTROL

UPDOWN

CLOCK

VOLUME+,–

PHONES

Top Cover

STANDBY/ON indicator

PHONES

When the System is Turned Off (STANDBY MODE)

Each time you press the DIMMER button on the Remote Control, the brightness of the backlighting changes as follows:

No backlighting = Dark backlighting = (back to the beginning)

• When the System is turned off again after power on, the brightness in Standby mode will be restored to the previous one since the brightness setting in Standby mode is stored in memory.

Turning the System Off

Press the % button again.

The Top Cover moves back to the original position. “GOOD BYE” is displayed and the display goes out , except for the clock display. The STANDBY/ON ind icator lights in red.

■Some power is always consumed even though power is

turned off (called Standby Mode).

■To switch off the System completely, unplug the AC

power cord from the wall outlet. When you unplug the AC power cord, the clock will be reset to 0:00 after about 20 minutes.

Adjusting the Brightness (DIMMER)

You can adjust the brightness of the backlightin g for the display.

When the System is Turned On

Each time you press the DIMMER button on the Remote Control, the brightness of the backlighting changes as follows: Bright = Dark = (back to the beginning)

Adjusting the Volume

Press the VOLUME + button to increase the volume or press the VOLUME – button to decrease it.

You can adjust the volume level between 0 and 50.

CAUTION:

• DO NOT turn on the System and/or start playing any source without first setting the VOLUME control to minimum, as a sudden blast of sound could damage your hearing, speakers and/or headphones.

For private listening

Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on headphones.

Page 12

Basic Operations

Basic OperationsBasic Operations

Fade-out Muting (FADE MUTING)

You can mute the output with one touch operation. To mute the output, press the FADE MUTING button

on the Remote Control. Then, the output will be faded out and becomes 0.

To release muting, press the FADE MUTING button once again. Then, the output will be faded in to the original level.

Reinforcing the Bass Sound (AHB PRO)

You can reinforce the bass sound to maintain rich, full bass at low volume. To get the effect, press the AHB (Active Hyper Bass) PRO button. The “AHB PRO” indicator lights up on the display. To cancel the effect, press the button again. The “AHB PRO” indicator goes out.

Tone Control (BASS/TREBLE)

You can control the tone by changing the bass and treble.

BASS Control

You can adjust the bass level (low frequency range level) between –6 and +6. (0: Flat)

Showing the Time (CLOCK/DISPLAY)

You can show the current time on the display. To display the clock, press the CLOCK button on the

Unit or DISPLAY button on the Remote Control. To return to the previous mode, press the same button again.

• To let the clock work, you need to set the clock first. (See “Setting the Clock” on page 17.)

Sliding the Top Cover (DOOR SLIDE)

Each time you press the DOOR SLIDE button on the Remote Control, the Top Cover slides back and forth.

Slide the Top Cover backward to allow Unit’s top button operation. Slide it toward you to cover the buttons.

Press the BASS button on the Remote

Control.

Press the UP or DOWN button on the

Remote Control to adjust the bass level.

DOWN

BASS

TREBLE Control

You can adjust the treble level (high frequency range level) between –6 and +6. (0: Flat)

Press the TREBLE button on the

Remote Control.

Press the UP or DOWN button on the

Remote Control to adjust the treble level.

DOWN

TREBLE

Page 13

Using the Tuner

REMOTE CONTROL

DIMMER SLEEP

AUTO

DISPLAY FM MODE

AUTO

PRESET

SET

PRESET

PROGRAM

REPEATRANDOM

DOOR SLIDE

BASS TREBLE CANCEL

SET

DOWN

VOLUME

AHB PRO

FADE MUTING

MD/AUX FM / AM

* When the System is in use, the display shows other items as well.

For simplicity, we show here only the items described in this section.

FM MODE

DOWN

FM/AM

PRESET TUNING

PRESET TUNINGFM/AMMD/AUX

AHB PRO CLOCK TIMER VOLUME

MULTI CONTROL

UPDOWN

Band display, Frequency display, Preset channel

FM mode indicators

STEREO MONO

You can listen to FM and AM (MW/LW) stati ons. Stations can be tuned in manually, automatically, or from preset memory storage.

■Before listening to the radio:

• Make sure that both the FM and AM (MW/LW) antennas are correctly connec te d. (Se e pa ge s 4 and 5 ) .

One Touch Radio

Just press the FM/AM button to turn on the System an d start playing the station you were last tuned to.

■You can switch from any other sound source to th e radio

by pressing the FM/AM button.

Tuning In a Station

Press the FM/AM button.

The Band and Frequency you were last tuned to appear on the display. (If the last station was selected using the preset number , the preset number appears first.) Each time you press the button, the band alternates between FM and AM (MW/LW).

FM / AM

FMAM

(on the Remote Control)

Select a station using one of the follow-

ing methods.

●Manual Tuning

Press the 4 or ¢ button on the Unit or the Remote Control repeatedly to move from frequency to frequency until you find the station you want.

FM/AM

FMAM

(on the Unit)

●Auto Tuning

If you press and hold the 4 or ¢ button on the Unit or the Remote Control for one second or more, the frequency changes down, or u p, automatically until a station is found.

●Preset Tuning using the Remote Control

(Possible only after presetting stations)

Select the desired preset number using the UP, DOWN, > and < button on the Remote Control. After 1 second the display will show the preset number’s band and frequency.

Example:

Press the UP button until the preset number 12 “P12” appears.

DOWN

(After 1 second)

●Preset Tuning using the Unit

Press the PRESET TUNING button to select the desired preset number. Its band and frequency are displayed.

• In AM broadcast, reception sensitivity will be changed by turning the AM loop antenna. Turn the AM loop antenna for best reception.

Page 14

Using the Tuner

FM / AM

AUTO

PRESET

MONO

FM MODE

Using the Tuner

Using the TunerUsing the Tuner

Presetting Stations

You can preset up to 30 FM stations and up to 15 AM (MW/ LW) stations using the Remote Control.

• Preset numbers may have been set to factory test frequencies prior to shipment. This is not a malfunction. You can preset the stations you want into memory by following one of the presetting methods below.

Manual Presetting

SET STORED

FM / AM

When changing the Band

Select a band by pressing the FM/AM

SET

DOWN

FM = 30, AM = 15

button.

Press the 4 or ¢ button to tune in a

station. Press the SET button.

“SET” will blink for 5 seconds. Within 5 seconds, proceed to the next step. When the display returns to the one set in step 2 after 5 seconds, press the SET button again.

SET

Auto Presetting

In each band, you can automatically preset FM-30, AM-15 (MW/LW) stations. Preset numbers will be allocated as stations are found, starting from the lowest frequency and moving up the frequency.

(for 2 seconds)

Select a band by pressing the FM/AM

button.

Press the AUTO PRESET button on the

Remote Control for more than two seconds.

Repeat steps 1-2 for the other band.

■If you want to change the preset stations, carry out the

Manual Presetting for the desired preset numbers.

CAUTION:

• Even if the system is unplugged or if the power failure occurs, the preset stations will be stored for about 24 hours. However, in case the preset stations are erased, you will need to preset the stations again.

Press the UP, DOWN, >, or < button

within 5 seconds to select the preset number.

UP or DOWN button:Increase or decrease the preset

number by 1. Pressing and holding the button will continuously increase or decrease the preset number.

> or < button: Increase or decrease the preset

number by 1. Pressing and holding the button will rapidly increase or decrease the preset number.

Press the SET button within 5 seconds.

“STORED” appears and after 2 seconds, the display returns to the broadcast frequency display.

Repeat above steps 1 to 5 for each sta-

tion you want to store in memory with a preset number.

To change the preset stations, repeat the same

steps as above.

To Change the FM Reception Mode

When you are tuned into an FM stereo broadcast, the “STEREO” indicator lights up and you can hear stereo effects. If an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose stereo effect.

Press the FM MODE button on the Remote Control so that the “MONO” indicator lights up on the display.

To restore the stereo effect, press the FM MODE button

on the Remote Control so that the “MONO” indicator goes off.

Page 15

Using the CD Player

STANDBY/ON% OPEN/CLOSE

PHONES

REMOTE CONTROL

DIMMER SLEEP

AUTO

DISPLAY FM MODE

PRESET

PROGRAM

RANDOM

SET

#/8

REPEATRANDOM

DOOR

SLIDE

BASS TREBLE CANCEL

SET

DOWN

VOLUME

AHB PRO

FADE MUTING

MD/AUX FM / AM

REPEAT CD

CANCEL UP

DOWN

¢ 7

PRESET TUNINGFM/AMMD/AUX

AHB PRO CLOCK TIMER VOLUME

Track number, Playing time, Preset number

PROGRAM

MULTI CONTROL

RANDOM ALL

987654321

UPDOWN

#¥8

2019181716151413121110

Top Cover

OPEN/CLOSE

Play mode indicators

You can use Normal, Random, Program or Repeat Play. Repeat Play can repeat all the tracks or just one of the tracks on the CD. Here are the basic things you need to know to play a CD and locate the different tracks on it.

This unit has been designed only to playback the CDs bearing the marks.

When playing a CD-R or CD-RW

You can play back finalized CD-R or CD-RW recorded music CD format.

■You can play back CD-R or CD-RW like CD.

■Some CD-R or CD-RW may not be played back on this

unit because of their disc characteristics, damage or stain on them, or if the player lens is dirty.

■The reflection factor of CD-RW is lower than that of oth-

er CD, possibly causing CD-RW to take longer to read.

The Quickest Way To Start a CD Is With the One Touch Operation

■Press the CD #¥8 button on the Remote Control.

• The power is automatically turned on and the Top Cover moves backward to allow the Unit’s top button operation. If a CD is already inserted, it will start playing from the first track.

• If no CD is inserted, “NO DISC” appears on the display and the CD Player remains in Stop mode.

Music calendar

Track number exceeding 20 is not displayed.

* When the System is in use, the display shows other items as well.

For simplicity, we show here only the items described in this section.

To Insert a CD

Press the OPEN/CLOSE button on the

Unit (or the CD 0 button on the Remote Control).

The Top Cover opens.

Place a CD, with its label side up as

shown below. Press down on the CD’s center until you hear a click.

Press the OPEN/CLOSE button (or CD 0

button) again to close the Top Cover.

• T o close the Top Cover and play the CD, you can just press the CD #¥8 button.

■You can place an 8 cm (3'') CD without an adaptor.

■If the CD cannot be read correctly (because it is

scratched, for example), “ 0 0:00” appears on the disp lay.

■You can insert a CD while listening to the other source.

CAUTION:

• DO NOT try to open or close the Top Cover by hands as it will be damaged.

Page 16

Using the CD Player

Using the CD PlayerUsing the CD Player

To Unload a CD

Take out the CD as shown below.

To pause, press the CD #¥8 button. The playback time blinks on the display. To cancel pause, press the same button again. Play continues from the point where it was paused.

To Select a Track or Passage within a Track

During playback, press the 4 or ¢ (< or >) button to select the track you want.

• The selected track starts playing.

•Press the ¢ or > button once to skip to the beginning of the next track.

•Press the 4 or < button to skip to the beginning of the track being played. Press twice quic kly to skip to the beginning of the previous track.

• When the > or < button on the Remote Cont rol is kept pressing, the track continuously skips.

Search Play

Holding down the 4 or ¢ button, during pl ayback, will fast forward/backwards the CD so you can quickly find a particular passage in the track you are listening to.

Programming the Playing Order of the Tracks

Basics of Using the CD Player-Normal Play

To Play a CD

Insert a CD.

Press the CD

The first track of the CD begins playing.

Track number Playback time

• The track number that has already played disappears from the music calendar.

• The CD Player automatically stops when the last track of the CD has finished playing.

To stop playing the CD, press the 7 button. The following information for the CD is displayed.

#¥8

button.

You can program the playing order of the tra cks using the Remote Control.

■You can program up to 32 tracks in any desired order in-

cluding the same tracks.

■You can only make a program when the CD Player is

stopped.

Insert a CD.

Press the CD #/8 button.

Press the 7 button to stop the CD.

Press the PROGRAM button.

The System enters the programming mode and the “PROGRAM” indicator lights up.

PROGRAM

Press the UP, DOWN, >, or < button to

select the track to program.

UP or > button: Increases the track number by 1. DOWN or < button:Decreases the track number by 1.

• When the > or < button is kept pressing, the track number changes rapidly.

Total track number Total playback time

To stop playing and remove the CD, press the OPEN/CLOSE button on the Unit or CD 0 button on the Remote Control to open the Top Cover.

Page 17

Press the SET button.

DOWN

Repeat steps 5 and 6 to select the other

SET

Total playback time of the programmed tracks

Program order number

(After 2 seconds)

tracks for the program.

You can see the total playback time of programmed tracks on the display. Also, you can see the programmed tracks on the music calendar.

Press the CD

The System plays the tracks in the order you have programmed them.

■You can skip to a particular program track by pressing the

4 or ¢ button during Program Play.

■To stop playing, press the 7 button once.

To confirm the programmed tracks while the CD player is stopped,

ton; the tracks making up the program will successively be displayed in the programmed order.

To delete all the tracks in the program,

press the 7 button. Pressing the CD 0 button to open the Top Cover will also clear the programmed tracks.

To exit the program mode once,

is stopped, press the PROGRAM button to light off the “PROGRAM” indicator.

• If the total playback time of the programmed tracks exceeds 99 minutes 59 seconds, the total playback time will go out on the display.

• If you try to program the 33rd track, “MEMORY FULL” appears on the display for about 2 seconds.

#/8

button.

each time press the 4 or ¢ but-

in stop mode,

while the CD Player

Using the CD Player

Using the CD PlayerUsing the CD Player

Random Play

The tracks will play in no special order when you use this mode.

Press the RANDOM button on the

Remote Control.

The “RANDOM” indicator lights up on the display.

Press the CD #/8 button.

The tracks are played in random order.

To skip a track during playback,

to jump to the next track in the random sequence. Press the 4 button to jump back to the start of a track being played.

To exit Random Play mode,

stopped, press the RANDOM button to light off t he “ RANDOM” indicator and carry out Normal Play, or press the CD 0 button to open the Top Cover.

press the ¢ button

while the CD Player is

Repeating Tracks

You can repeat all tracks or individual track , as many ti mes as you like.

Press the REPEAT button on the Remote Control.

The Repeat indicator changes with each press of the button, as shown below.

ALL=blank display = (back to the

beginning)

: Repeats one track. : In Normal Play mode, repeats all the tracks.

ALL

In Program Play mode, repeats all the tracks in the program. In Random Play mode, repeats all the tracks in random order.

To exit Repeat mode,

Repeat indicator on the display goes out.

■In Random Play, cannot be selected.

■Repeat mode remains in effect even when you change the

play mode.

press the REPEAT button until the

To Modify the Program

Modify the contents of the program while the CD Player is stopped. Each time you press the CANCEL button, the last track in the program is deleted. To add new tracks to the end of the program, repeat above steps 5 to 7.

Page 18

Using External Equipments

REMOTE CONTROL

DIMMER SLEEP

AUTO

DISPLAY FM MODE

PRESET

MD/AUX

PROGRAM

FADE MUTING

MD/AUX FM / AM

DOOR

AHB PRO

SLIDE

BASS TREBLE CANCEL

SET

DOWN

VOLUME

REPEATRANDOM

PRESET TUNINGFM/AMMD/AUX

AHB PRO CLOCK TIMER VOLUME

MULTI CONTROL

UPDOWN

MD/AUX

Listening to External Equipment

You can listen to external equipment such as MD recorder, turntable or other auxiliary.

■First make sure that the external equipment is properly connected to the System. (See page 7).

Set the VOLUME control to the mini-

mum position.

Press the MD/AUX button.

“MD/AUX” appears on the display.

Start playing the external equipment.

Adjust the VOLUME control to the

desired listening level. Apply sound effects, if you wish.

■Press the AHB PRO button to reinforce the bass sound.

■Press the BASS/TREBLE button on the Remote Control

to control the tone. (See “Tone Control” on page 10.)

To exit MD/AUX mode, you will automatically switch out of MD/AUX mode when you select another source.

Recording the System’s Source to External Equipment

You can record the System’s source to external equipment which is connected to the MD/AUX-IN/OUT or CD DIGITAL OUT terminals of the System, such as cassette deck or MD recorder, etc.

■First make sure that the external equipment is properly

connected to the System. (See page 7).

Play the System’s CD Player or tune in to a station.

■The recording level is not affected by the VOLUME level

set by the System. Also it is not affected by the so und effects.

• For operation of the external equipment, refer to its Instructions.

Page 19

Using the Timers

REMOTE CONTROL

DIMMER SLEEP

AUTO

DISPLAY FM MODE

SLEEP

PRESET

PROGRAM

DOOR

AHB PRO

SLIDE

BASS TREBLE CANCEL

SET

DOWN

FADE MUTING

MD/AUX FM / AM

REPEATRANDOM

PRESET

TUNINGFM/AMMD/AUX

AHB PRO CLOCK TIMER VOLUME

MULTI CONTROL

UPDOWN

CLOCK

TIMER

ON time, OFF time, Source, Volume

VOLUME

* When the System is in use, the display shows other items as well.

For simplicity, we show here only the items described in this section.

The timers let you control listening functions automatically.

Setting the Clock

• Use the Unit’s button to set the clock.

• When you plug the AC power cord into the wall outlet, the time indication “0:00” blinks on the display.

• The clock must be correctly set for the timers to work.

• The procedure must be completed within two minutes. Otherwise, the setting is cleared and must be repeated from the beginning.

Press the %%%% button.

Then, the Unit’s top buttons appear.

SLEEP

Press the ¢ or 4 button to set the

Timer indicator SLEEP indicator

minute. Press the CLOCK button.

The selected time is set and the seconds start counting from 0.

CAUTION:

• If there is a power failure, the clock loses its setting after about 20 minutes. “0:00” blinks on the display and the clock must be reset.

• The clock may gain or lose one to two minutes per month.

CLOCK

MULTI CONTROL

(for 2 seconds)

Press the CLOCK button on the Unit for

more than two seconds.

The hour digit of the time indication rapidly blinks on the display.

Press the ¢ or 4 button on the Unit

to set the hour.

Pressing the ¢ button moves the time forwards and pressing the 4 button moves it backwards. Hold down the button to move the time rapidly.

Press the CLOCK button.

The minute digits of th e time indicatio n rapidly bli nk on the display.

CLOCK

UPDOWN

Setting the Daily Timer

Once you have set the Daily Timer, the timer will be activated at the same time every day. The Timer indicator on the display shows that the Daily Timer you have set is in effect.

• Use the Unit’s button to set the timer.

• Perform each setting within 30 seconds. Otherwise, setting will be cleared and the procedure must be repeated from the beginning.

Page 20

Using the Timers

Using the TimersUsing the Timers

Setting the ON time (Example: 10:15).

1. Press the TIMER button on the Unit for more than two seconds. The Timer indicator lights up and the hour d igit of the current ON time blinks on the display.

• When the clock is not set, “CLOCK” and “ ADJUST” appear alternately on the display. Set the clock first.

Press the ¢ or 4 button on the Unit to set the hour you want the Unit to come on. Pressing the ¢ button moves the time forwards and pressing the 4 button moves it backwards. Hold down the button to move the time rapidly.

2. Press the TIMER button. The minute digits of the ON time blink on the displa y.

Set the minute you want the Unit to be turned off, using the ¢ and 4 buttons.

Selecting the music source.

1. Press the TIMER button. The “TUNER” or “CD” blinks on the display.

2. Press the ¢ or 4 button to select the music source you want to listen to. The display changes as shown below.

TUNER

Setting the volume level.

1. Press the TIMER button. The current volume setting blinks on the display.

2. Press the ¢ or 4 button to select the volume level.

-- :The current volume level will be used. 0 to 50 :When the timer is turned on, the Volume

ÔCDÔ

(back to the beginning)

will be automatically set to the selected level.

Set the minute you want the Unit to come on, using the ¢ or 4 button.

Setting the OFF time (Example: 13:30).

1. Press the TIMER button. The hour digit of the OFF time blinks on the display. (The same time as the ON time will be automatically set.)

Set the hour you want the Unit to be turned off, using the ¢ or 4 button.

2. Press the TIMER button. The minute digits of the OFF time blink on the display.

Press the TIMER button.

The timer setting is completed and the display returns to the display before you set the Timer. The Timer indicator remains lit.

Before turning off the System, prepare

the music source selected in step 3.

TUNER: Tune in to the desired station. CD: Insert a CD. (Playback will start from the first

track at Timer on.)

Press the

button to turn off the Sys-

%%%%

tem.

In standby mode, you can see the Timer indicator ( ) on the display.

• When the timer turns on, the Timer indicator starts blinking and the prepared source in step 6 will be played.

To cancel the timer, press the TIMER button. The Timer indicator ( ) goes out on the display. To re-activate the cancelled timer, press the TIMER button to light the Timer indicator ( ). At this time, you can see the current timer settings. Each setting appears on the display for two seconds in the order of ON time, OFF time, music source and volume. To change the timer setting, repeat the setting procedure from the beginning.

CAUTION:

• If the System is unplugged, or a power failure occurs, the timer setting will be lost. You will need to reset the clock first, then the timer.

Page 21

Setting the SLEEP Timer

(Using the Remote Control)

Use the Sleep Timer to turn the System off after a certain number of minutes when it is playing. By setting the Sleep Timer, you can fall asleep to music and know that your System will turn off by itself rather than play all night.

■You can only set the Sleep Timer when the System is on

and a source is playing.

Play a CD or tune in to the desired sta-

tion.

Press the SLEEP button on the Remote

Control.

The “SLEEP” indicator lights up.

■When the clock is not set, “CLOCK” and “ADJUST”

appear alternately on th e disp la y. Set th e c lock at first.

Set the length of time you want the

source to play before shutting off.

• Each time you press the SLEEP button, it changes the number of minutes shown on the display in this sequence:

= 20 = 30 = 60 = 90 = 120 = Cancelled =

(back to the beginning)

Using the Timers

Using the TimersUsing the Timers

The selected number of minutes for the Sleep Timer will stop blinking five seconds later and the display returns to the original one before setting the Sleep Timer. (The display is dimmed.) The System is now set to turn off after the number of minutes you set.

To Confirm the Sleep Time:

When the SLEEP button is pressed, the remaining sleep time is displayed. Wait until the display returns to the original display.

To Cancel the SLEEP Timer Setting:

Press the SLEEP button until the “SLEEP” indicator goes out on the display. Turning off the System also cancels the SLEEP Timer.

■If you are setting the Daily Timer, the System will be

turned on at the set time to wake you up.

Page 22

Care And Maintenance

Handle your CDs carefully, and they will last a long time.

Compact Discs

• Only CDs bearing this mark can be used with this System. However, continued use of irregular shape CDs (heart-shape, octagonal, etc.) can damage the System.

• Remove the CD from its case by holding it at the edges while pressing the case’s center hole lightly.

• Do not touch the shiny surface of the CD, or bend the CD.

• Put the CD back in its case after use to prevent warping.

• Be careful not to scratch the surface of the CD when placing it back in the case.

• A void e xposure to direct su nlight, temperature extremes, and moisture.

Cleaning the Lens

If the lens in the CD pickup is dirty, dropout, etc., could degrade sound. Open the Top Cover and clean the lens as shown.

• Use a blower (available from a camera store) to blow dust off the lens.

Blower

Lens

• If there are fingerprints, etc. on the lens, gently wipe clean with a cotton swab.

• A dirty CD may not play correctly . If a CD does become dirty, wipe it with a soft cloth in a straight line from center to edge.

CAUTION:

• Do not use any solvent (for example, conventional record cleaner, spray thinner, benzine, etc.) to clean a CD.

General Notes

In general, you will have the best performance by keeping your CDs and the mechanism clean.

• Store CDs in their cases, and keep them in cabinets or on shelves.

• Keep the System’s Top Cover closed when not in use.

Cleaning the unit

• Stains on the unit Should be wiped off with a soft cloth. If the unit is heav ily stained, wipe it witha cloth soaked in water-diluted neutral detergent and wrung well, then wipe clean with a dry cloth.

• Since the unit may deteriorate in quality, become damaged or get its paint peeled off, be careful about the followings.

- DO NOT wipe it with a hard cloth.

- DO NOT wipe it strong.

- DO NOT wipe it with thinner or benzine.

- DO NOT apply any volatile substance such as insecti-

cides to it.

- DO NOT allow any rubber or plastic to remain in con-

tact with it for a long time.

Moisture Condensation

Moisture may condense on the lens inside the System in the following cases:

• After turning on heating in the room.

• In a damp room.

• If the System is brought directly from a cold to a warm place.

Should this occur, the System may malfunction. In this case, leave the System turned on for a few hours until the moisture evaporates, unplug the AC power cord, and then plug it in again.

Page 23

Troubleshooting

• If you are having a problem with your System, check this list for a possible solution before calling for service.

Symptom Possible Cause Action

No sound is heard. • Connections are incorrect, or loose.

• Headphones are connected.

Poor radio reception • The antenna is disconnected.

• The AM Loop Antenna is too close to the System.

• The FM Wire Antenna is not properly extended and positioned.

The CD skips. The CD is dirty or scratched. Clean or replace the CD. The CD does not play. The CD is upside down. Put the CD in with the label side up. Unable to operate the Remote Control. • The path between the Remote Con-

trol and the sensor on the Unit is blocked.

• The batteries have lost their charge.

Operations are disabled. The built-in microprocessor has mal-

functioned due to external electrical interference.

• If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a qualified person, such as your dealer , for service.

• Check all connections and make corrections. (See pages 4 to 8.)

• Disconnect the headphones.

• Reconnect the antenna securely.

• Change the position and direction of the AM Loop Antenna.

• Extend FM Wire Antenn a to the be st reception position.

• Remove the obstruction.

• Replace the batteries.

Unplug the System then plug it back in after a few minutes.

NO DISC appears.

There is no disc in the tray, or CD, CD-R or CD-RW that hasn’t yet been finalized (including blank discs) has been inserted.

Insert a CD, CD-R or CD-RW that has been finalized.

Page 24

Specifications

Amplifier

Output Power

Input Sensitivity/Impedance (1 kHz)

MD/AUX IN

Output Sensitivity/Impedance (1 kHz)

MD/AUX OUT

CD DIGITAL OUT (Optical out)

Speaker terminals

Subwoofer out

Phones

CD Player

Signal-To-Noise Ratio

Wow And Flutter

Tuner

FM Tuner

Tuning Range 87.5 MHz - 108.0 MHz

AM Tuner

Tuning Range

Center Unit (FS-SD550/SD770/SD990)

Dimensions

Mass

Speaker Specifications (each unit)

FS-SD550

Speakers

Impedance

Dimensions

Mass

38 W (19 W + 19 W) at 4 ohms (Max.) 30 W (15 W + 15 W) at 4 ohms (10% THD)

500 mV/47 kohms 500 mV/5 kohms

–21 dBm - –15 dBm 4 - 16 ohms 230mV/19kohms 16 ohms - 1 kohm 0 - 15 mW/ch output into 32 ohms

90 dB Unmeasurable

(MW) 522 kHz – 1, 629kHz (LW) 144 kHz – 288kHz

300mm Approx. 3.0kg

8 cm cone 4 ohms 109mm

1.5kg

75mm ✕ 215mm (W/H/D)

217mm ✕ 165mm (W/H/D)

FS-SD770

Speakers

Impedance

Dimensions

FS-SD990

Speakers

Impedance

Dimensions

Accessories

Power Specifications

Power Requirements

Power Consumption

Design and specifications are subject to change without notice.

8 cm cone 4 ohms 120mm

1.4kg

Mass

8 cm cone 4 ohms 120mm

1.4kg

Mass

Power Cord (1) AM Loop Antenna (1) Remote Control (1) Batteries R6P (SUM-3)/AA (15F) (2) FM Wire Antenna (1) Speaker Cords (2)

AC 240 V ~ , 50 Hz 25 watts (power on mode)

1.9 watts (in Standby mode)

246mm ✕ 162mm (W/H/D)

VICTOR COMPANY OF JAPAN, LIMITED

0201MZMCREHIT