Original instructions for use
Before using the machine read the instructions for use.
JURA Type 737
Page 2
Table of contents
Your WE8
Control elements 4
Important information 6
Proper use ......................................................................................................................................................6
For your safety ...............................................................................................................................................6
1 Preparing and using for the first time 10
JURA on the Internet ....................................................................................................................................10
Setting up the machine ..............................................................................................................................10
Filling the bean container ...........................................................................................................................10
Determining the water hardness ..............................................................................................................10
First-time use .................................................................................................................................................11
Permanently setting the amount of water for the cup size .................................................................17
Adjusting the grinder ..................................................................................................................................18
Hot water .......................................................................................................................................................18
3 Daily operation 19
Filling the water tank ...................................................................................................................................19
Switching on the machine ..........................................................................................................................19
Milk system rinsing .....................................................................................................................................25
Setting the water hardness .......................................................................................................................26
Unit for amount of water ...........................................................................................................................26
Language ......................................................................................................................................................26
Query counter readings and version .......................................................................................................27
2
Page 3
Table of contents
5 Maintenance 28
Rinsing the machine ...................................................................................................................................28
Rinsing the milk system .............................................................................................................................28
Cleaning the fine foam frother .................................................................................................................29
Dismantling and rinsing the fine foam frother......................................................................................30
Inserting/changing the filter .......................................................................................................................31
Cleaning the machine ................................................................................................................................32
Descaling the machine .............................................................................................................................. 33
Cleaning the bean container .....................................................................................................................35
Descaling the water tank ........................................................................................................................... 35
6 Display messages 36
7 Troubleshooting 37
8 Transport and environmentally friendly disposal 38
Transport/ Emptying the system .............................................................................................................38
9 Technical data 39
10 Index 40
11 JURA contact details/ Legal information 44
Symbol description
Warnings
J WARNING
J CAUTION
CAUTIONCAUTION draws your attention to potential damage to the machine.
Symbols used
T
E
‘Coffee’Display
Always take note of any information marked with the words CAUTION
or WARNING and a warning sign. The signal word WARNING draws your
attention to potential serious injury, and the signal word CAUTION to
potential minor injury.
Prompt to take action. This symbol means that you are being prompted to
perform some action.
Information and tips to make it even easier to use your WE8.
3
Page 4
Control elements
9
Control elements
1
2
3
4
5
6
7
8
1 Filler funnel cover
2 Filler funnel for ground coffee
3 Bean container with aroma preservation
cover
4 Water tank cover
5 Water tank
6 Plug-in mains cable (back of the machine)
7 Coffee grounds container
8 Drip tray
10
11
12
13
14
9 Cover cap for grinder adjustment switch
10 Grinder adjustment switch
11 On/Off button Q
12 Milk system with fine foam frother
13 Height-adjustable coffee spout
14 Cup grille
4
Page 5
Control elements
1
2
1 Display 2 Multi-function buttons (button function
depends on what is shown in the display)
Service socket for optional
JURA Smart Connect
Accessories
6
Container for milk system
cleaning
Professional fine foam
G2
frother
(optional)
Measuring spoon for ground
coffee
Hot-water nozzle
5
Page 6
Important information
Important information
Proper use
For your safety
This machine is intended for use by specialist or
trained staff in businesses, light industry and agricultural facilities or for commercial use by non-professionals. It should only be used for coffee preparation and to heat milk and water. Use for any other
purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the
consequences of improper use.
Before using the machine read these instructions
for use thoroughly and completely and comply
with the instructions they contain. A warranty service is not applicable for damage or defects caused
by non-compliance with the instructions for use.
Keep these instructions for use close to the machine
and pass them on to the next user.
The WE8 may only be operated by instructed persons. Non-professionals must be supervised during use.
Please carefully read and observe the important
safety information set out below.
J
6
To avoid danger of potentially fatal electric shock:
Never use a machine which is damaged or has
U
a defective mains cable.
In the event of signs of damage, for example if
U
there is a smell of burning, unplug the machine
immediately from the mains supply and contact JURA service.
If the mains cable of this machine is damaged
U
it must be replaced with a special mains cable,
Page 7
Important information
which is available directly from JURA or from
authorised JURA service centres.
Make sure that the WE8 and the mains cable
U
are not located close to hot surfaces.
Be careful to ensure that the mains cable is not
U
trapped and does not rub against sharp edges.
Never open and repair the machine yourself.
U
Do not modify the machine in any way that is
not described in these instructions for use. The
machine contains live parts. If opened, there is
a danger of potentially fatal injury. Repairs
may only be carried out by authorised JURA
service centres, using original spare parts and
accessories.
To completely and safely disconnect the
U
machine from the power supply, first switch
off the WE8 using the On/Off button Q. Only
then should you remove the mains plug from
the power socket.
There is a risk of scalds or burns on the spouts and
fine foam frother:
Place the machine out of the reach of children.
U
Do not touch any hot parts. Use the handles
U
provided.
Be careful to ensure that the fine foam frother
U
is correctly installed and clean. If incorrectly
fitted or if it becomes blocked, the fine foam
frother or its parts might come off.
A defective machine is not safe and could cause
injury or fire. To avoid damage and any associated
risk of injury or fire:
Never allow the mains cable to loosely hang
U
down. The mains cable could pose a tripping
hazard or become damaged.
7
Page 8
Important information
Protect the WE8 from environmental influ-
U
ences such as rain, frost and direct sunlight.
Do not immerse the WE8, mains cable or con-
U
nections in water.
Do not put the WE8 or any individual parts in
U
the dishwasher.
Before cleaning, switch the WE8 off with the
U
On/Off button Q. Always wipe the WE8 with a
damp cloth rather than a wet one, and protect
it from prolonged exposure to water splash.
The WE8 is not suitable for installation on a
U
surface where a jet of water can be used.
The machine must not be cleaned with a jet of
U
water.
Do not use alkaline cleaning agents; only use
U
a soft cloth and mild cleaning agents.
Please only use original JURA maintenance
U
products. Use of products that are not explicitly recommended by JURA could damage the
machine.
Only connect the machine to the mains volt-
U
age in accordance with the information on the
rating plate. The rating plate is located on the
underside of your WE8. Further technical data
is provided in these instructions for use (see
Chapter 9 ‘Technical data’).
Connect the WE8 directly to a domestic power
U
socket. Using multi-socket adapters or extension cords may cause overheating.
Do not use any coffee beans treated with addi-
U
tives or caramelised coffee beans.
Only fill the water tank with fresh, cold water.
U
8
Page 9
Important information
Switch the machine off with the On/Off but-
U
ton Q if you are going to be absent for a longer
period of time and remove the mains plug
from the power socket.
Children may not clean or service the machine
U
unless supervised by a responsible person.
Do not allow children to play with the machine.
U
Keep children under the age of 8 away from
U
the machine, or supervise them constantly.
Children aged 8 and over may only operate
U
the machine without supervision if they have
been instructed in how to use it safely. Children must be able to recognise and understand the potential dangers arising from incorrect use.
People, including children, who
do not have the physical, sensory or mental
U
capabilities to use the machine safely or
are inexperienced or lack knowledge in how to
U
use the machine safely
must be supervised by a responsible person when
using it, or must be instructed in how to use it correctly.
Safety when handling the CLARIS Pro Smart filter
cartridge:
Filter cartridges should be kept out of the
U
reach of children.
Store filter cartridges in a dry place in the
U
sealed packaging.
Protect cartridges from heat and direct sun-
U
light.
Do not use damaged filter cartridges.
U
Do not open filter cartridges.
U
9
Page 10
1 Preparing and using for the first time
1 Preparing and using for the first time
JURA on the Internet
Setting up the machine
Filling the bean container
CAUTION
Visit us on the Internet. You can download short operating instructions for your machine from the JURA website (www.jura.com). You
will also find interesting and up-to-date information on your WE8
and on every aspect of coffee.
If you need assistance with using your machine, you can find this at
www.jura.com/service.
When setting up your WE8, please note the following:
Place the WE8 on a horizontal surface that is not sensitive to
U
water (minimum height of 80cm).
Choose a spot for your WE8 which protects the machine
U
against overheating. Ensure that the ventilation slots are not
covered.
Coffee beans which have been treated with additives (e.g. sugar),
ground coffee or freeze-dried coffee will damage the grinder.
T Only use roasted, untreated coffee beans to fill the bean con-
tainer.
Determining the water
hardness
10
T Remove the aroma preservation cover.
T Remove any dirt or foreign objects from inside the bean
container.
T Fill the bean container with coffee beans and close the
aroma preservation cover.
When you use the machine for the first time, you must set the water
hardness. If you do not know the hardness of your water, you can
find this out first. Use the Aquadur® test strips supplied with the
machine.
Page 11
First-time use
1 Preparing and using for the first time
T Hold the test strip briefly (for 1second) under flowing water.
Shake off the water.
T Wait for about 1minute.
T You will then be able to read the degree of water hardness
from the discolouration of the Aquadur® test strip and the
description on the packaging.
J
WARNING
CAUTION
If the machine is operated with a defective mains cable, there is a
danger of potentially fatal electric shock.
T Never use a machine which is damaged or has a defective
mains cable.
Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
Precondition:The bean container has been filled.
TConnect the mains cable to the machine.
TInsert the mains plug into a power socket.
T Press the On/Off button Q to switch the WE8 on.
‘Sprachauswahl’
E To display more languages, press the ‘> ’ button (bottom
right).
T Press the button that corresponds to the language you
want, e.g.
‘English’.
‘Saved’ appears briefly on the display to confirm the setting.
‘Water hardness’
E If you do not know the hardness of your water, you must find
this out first (see Chapter 1 ‘Preparing and using for the first
time – Determining the water hardness’).
11
Page 12
1 Preparing and using for the first time
T Press the ‘<’ or ‘>’ button to change the water hardness
setting, for example to
T Press the
‘Save’ button.
‘25°dH’.
‘Saved’ appears briefly on the display.
‘Use filter’
T Place a receptacle under the fine foam frother.
T Remove the water tank and rinse it with cold water.
T Open the filter holder.
T Insert the CLARIS Pro Smart filter cartridge into the water
tank, exerting slight pressure.
T Close the filter holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
E The machine automatically detects that you have just inserted
the filter cartridge.
‘Use filter’ / ‘Saved’
‘Filter is beingrinsed’
, the filter is rinsed. Water flows out of
the fine foam frother.
12
E The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
‘Empty drip tray’
T Empty the drip tray and put it back into the machine.
T Place one receptacle under the coffee spout and another
under the fine foam frother.
‘System is filling’
‘Machine is rinsing’
, the system is rinsed. The rinse stops
automatically. The start screen is displayed. Your WE8 is
ready for use.
E The start screen shows the products you can prepare. Press
the
‘>’ button to display more products.
E If the filter is active, this is indicated by a blue filter symbol on
the display.
Page 13
1 Preparing and using for the first time
Connecting milk
Connect accessory (with
wireless connection)
Your WE8 creates fine, creamy, feather-light milk foam with a perfect
consistency. The most important requirement for frothing milk is a
milk temperature of 4–8°C. We would therefore recommend using
a milk cooler or a milk container.
T Remove the protective cover from the fine foam frother.
T Connect the milk pipe to the fine foam frother.
T Connect the other end of the milk pipe to a milk container
or a milk cooler.
You have the option of connecting your WE8 wirelessly to a compatible accessory (e.g. the Cool Control milk cooler). To do this, the
receiver of the Cool Control or the JURA Smart Connect must be
plugged into the service socket.
E The Smart Connect can be protected against unauthorised
access using a PIN. Activate the PIN function via J.O.E.
®
– your
JURA app. You will find more information at
www.jura.com/smartconnect.
E Please note that you can only connect either the accessory or
®
J.O.E.
to the coffee machine via Smart Connect and not both
at the same time.
Precondition:The start screen is displayed.
T Position the accessory near the coffee machine (a maximum
of 0.5 m away).
T Switch on the accessory and the coffee machine.
T Press the reset button of the Smart Connect (e.g. with a
paper clip).
T Then (within 30 sec.) press and hold the reset button of the
accessory until the LED lights up to indicate the successful
connection.
13
Page 14
2 Preparation
2 Preparation
Basic information about preparing drinks:
The display shows four products you can prepare. Press the
U
‘>’ button to display more products.
During the grinding operation you can select the coffee
U
strength of single products by pressing the
tons.
During preparation you can change the preset amounts (e.g.
U
water and amount of milk foam) by pressing the
buttons.
You can stop preparation at any time. To do this, press the
U
‘Cancel’ button.
Coffee tastes best served hot. A cold porcelain cup cools the beverage – and impairs the taste. We therefore recommend prewarming
the cups. The full coffee aroma can develop only in prewarmed cups.
You can purchase a JURA cup warmer from your specialised dealer.
You can make permanent settings for all products in programming
mode (see Chapter 4 ‘Permanent settings in programming mode –
Adjusting the product settings’).
‘<’ and ‘>’ but-
‘<’ and ‘>’
Latte macchiato,
cappuccino and other
speciality coffees with
milk
14
Your WE8 prepares latte macchiato, cappuccino and other speciality
coffees with milk at the touch of a button. There is no need to move
the glass or cup.
E This chapter applies to the professional fine foam frother and
the fine foam frother.
Example:Proceed as follows to prepare one latte macchiato.
Precondition:The start screen is displayed. Milk is connected to the
fine foam frother.
T Place a glass under the fine foam frother.
T Press the
‘Latte macchiato’, the preset amount of milk foam flows into
the glass.
‘Latte macchiato’ button.
Page 15
2 Preparation
E There is a short interval while the hot milk separates from the
milk foam. This allows the typical layers of a latte macchiato
to form. You can choose the length of this interval in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Adjusting the product settings’).
Coffee preparation starts. The preset amount of water for
espresso flows into the glass. Preparation stops automatically. Your WE8 is once more ready for use.
To ensure that the fine foam frother always works properly, you
must clean it daily when you have been preparing milk (see Chap-
ter 5 ‘Maintenance – Cleaning the fine foam frother’).
Ristretto, espresso and
coffee
Two ristretti, two
espressi and two coffees
Example:Proceed as follows to prepare one coffee.
Precondition:The start screen is displayed.
T Place a cup under the coffee spout.
T Press the
Preparation starts.
played. The preset amount of water for coffee flows into the
cup.
Preparation stops automatically. Your WE8 is once more
ready for use.
To prepare two speciality coffees, press the appropriate preparation
button twice (within approximately 1 second).
Example:Proceed as follows to prepare two espressi.
Precondition:The start screen is displayed.
T Place two cups under the coffee spout.
T Press the
preparation.
‘2 espressi’, the preset amount of water flows into the cups.
Preparation stops automatically. Your WE8 is once more
ready for use.
‘Coffee’ button.
‘Coffee’ and the coffee strength are dis-
‘Espresso’ button twice (within 1 second) to start
Espresso doppio
‘Doppio’ is Italian for ‘double’. When you select Espresso doppio,
two espressi are prepared one after the other. The result is an extra
full-bodied and aromatic speciality coffee.
15
Page 16
2 Preparation
Milk foam
Ground coffee
E This chapter applies to the professional fine foam frother and
the fine foam frother.
Precondition:The start screen is displayed. Milk is connected to the
fine foam frother.
T Place a cup under the fine foam frother.
T Press the
‘1 portion milk’, the milk foam is prepared. The preset
amount flows into the cup.
Preparation stops automatically. Your WE8 is once more
ready for use.
To ensure that the fine foam frother always works properly, you
must clean it daily when you have been preparing milk (see Chap-
ter 5 ‘Maintenance – Cleaning the fine foam frother’).
You can choose to use a second coffee variety, for example decaffeinated coffee, with the filter funnel for ground coffee.
Basic information about ground coffee:
Never add more than two level measuring spoons of ground
U
coffee.
Use ground coffee which is not ground too finely. Very fine
U
coffee can block up the system so that the coffee only comes
out in drips.
If you did not fill the machine with a sufficient amount of
U
ground coffee,
the WE8 stops the operation.
The desired speciality coffee must be prepared within approx-
U
imately one minute after filling with the ground coffee. Otherwise the WE8 stops the operation and is once more ready
for use.
All speciality coffees with ground coffee are always prepared
U
following the same model.
‘1 portion milk’ button.
‘Not enough ground coffee’ is displayed and
16
Example:Proceed as follows to prepare one espresso using ground
coffee.
Precondition:The start screen is displayed.
T Place a cup under the coffee spout.
Page 17
2 Preparation
T Open the powder chute cover.
‘Ground coffee’ / ‘Please add ground coffee’
T Place one level measuring spoon of ground coffee into the
filler funnel.
T Close the cover of the filler funnel.
T Press the
Preparation starts.
espresso flows into the cup.
Preparation stops automatically. Your WE8 is once more
ready for use.
‘Espresso’ button.
‘Espresso’, the preset amount of water for
Permanently setting the
amount of water for the
cup size
It is easy to permanently adjust the amount of water for all single
products to the cup size. Adjust the amount once as shown in the
following example. Every time you prepare a drink in the future, this
amount will be dispensed.
Example:Proceed as follows to permanently set the amount of
water for one coffee.
Precondition:The start screen is displayed.
T Place a cup under the coffee spout.
T Press and hold the
Press button’
T Release the
Preparation starts and the coffee flows into the cup.
T Press any button except
coffee in the cup.
Preparation stops.
set amount of water for one coffee is permanently stored.
Your WE8 is once more ready for use.
E You can alter this setting at any time by repeating the above
procedure.
E You can also permanently set the amounts for all single prod-
ucts in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Adjusting the product settings’).
‘Coffee’ button.
‘Coffee’ button until ‘Enough coffee?
appears.
‘Cancel’ as soon as there is sufficient
‘Saved’ appears briefly on the display. The
17
Page 18
2 Preparation
Adjusting the grinder
CAUTION
You can adjust the grinder to suit the degree of roast of your coffee.
If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged.
T Only adjust the consistency of grind when the grinder is run-
ning.
The consistency of grind is correct if the coffee flows regularly from
the coffee spout. In addition a fine, thick crema forms.
Example:Proceed as follows to change the consistency of grind dur-
ing the preparation of an espresso.
Precondition:The start screen is displayed.
T Place a cup under the coffee spout.
T Open the cover of the grinder adjustment switch.
T Press the
T Turn the grinder adjustment switch to the desired position
while the grinder is running.
The preset amount of water flows into the cup. Preparation
stops automatically.
T Close the cover of the grinder adjustment switch.
‘Espresso’ button to start preparation.
Hot water
18
J
CAUTION
The WE8 allows you to prepare different variants of hot water:
‘Hot water’ and ‘Hot water for green tea’.
There is a danger of scalding from hot water splashes.
T Avoid direct contact with the skin.
Example:Proceed as follows to prepare hot water for green tea.
Precondition:The start screen is displayed.
T Place a cup under the fine foam frother.
T Press the
‘Hot water for green tea’, the preset amount of water flows
into the cup.
Preparation stops automatically. Your WE8 is once more
ready for use.
‘Hot water for green tea’ button.
Page 19
3 Daily operation
3 Daily operation
Filling the water tank
CAUTION
Switching on the
machine
Daily maintenance of the machine and hygiene when handling coffee and water are key to a perfect coffee result in the cup every time.
You should therefore change the water daily.
Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
T Open the water tank cover.
T Remove the water tank and rinse it with cold water.
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Close the water tank cover.
T Place a receptacle under the coffee spout.
T Press the On/Off button Q to switch the WE8 on.
‘Welcome to JURA’
‘Machine is rinsing’
automatically. The start screen is displayed. Your WE8 is
ready for use.
, the system is rinsed. The rinse stops
Daily maintenance
To ensure that you get many years of reliable service out of your
WE8 and to guarantee the optimum coffee quality, the machine
requires daily maintenance.
T Pull out the drip tray.
T Empty the coffee grounds container and the drip tray. Rinse
them both with warm water.
E Always empty the coffee grounds container when the machine
is switched on. This is the only way of resetting the coffee
grounds counter.
19
Page 20
3 Daily operation
T Refit the coffee grounds container and the drip tray.
T Rinse the water tank with clean water.
T Clean the fine foam frother (see Chapter 5 ‘Maintenance –
Cleaning the fine foam frother’).
T Remove the milk pipe and rinse it thoroughly under running
water.
T Dismantle and rinse the fine foam frother (see Chapter 5
‘Maintenance – Dismantling and rinsing the fine foam
frother’).
T Wipe the surface of the machine with a clean, soft, damp
cloth (e.g. microfibre cloth).
Regular maintenance
Switching off the
machine
Carry out the following maintenance actions regularly or as
required:
In the interests of hygiene, we recommend changing the milk
U
pipe and interchangeable milk spout on a regular basis
(approximately every 3 months). Replacements are available
from specialised dealers. Your WE8 is equipped with the HP3
milk system.
Clean the inside of the water tank, e.g. with a brush. Further
U
information about the water tank is provided in these instructions for use (see Chapter 5 ‘Maintenance – Descaling the
water tank’).
Traces of milk and coffee may stick to the top and bottom of
U
the cup grille. If this happens, clean the cup grille.
When the WE8 is switched off, the system is automatically rinsed if
a speciality coffee has been prepared.
T Place one receptacle under the coffee spout and another
under the fine foam frother.
T Press the On/Off button Q.
E If milk has been prepared, you will be prompted to clean the
milk system (
switch-off process continues automatically.
‘Clean the milk system’). After 10 seconds the
20
‘Machine is rinsing’, the system rinses itself. The operation
stops automatically. Your WE8 is switched off.
Page 21
4 Permanent settings in programming mode
4 Permanent settings in programming mode
Press the ‘Pc’ button to enter programming mode. You can navigate through the programme items and permanently save the
required settings using the multi-function buttons. The following
settings can be made:
Programme
item
‘1/6’‘Clean’,
‘2/6’‘Rinse the milk
‘3/6’‘Expert mode’
‘4/6’‘Choose language’
‘5/6’‘Water hardness’
‘6/6’‘Product counter’
Sub-itemExplanation
TStart the required maintenance programme here.
‘Descale’,
‘Clean the milk
system’
,
‘Filter’ (only if filter
is activated)
THere you can start the required maintenance
system’
,
‘Rinse the coffee
system’
,
‘Information’
‘Customise cup fill
volume’
‘One-off settings’
‘Lock/enable’
‘Units’
‘Switch off after’
‘Rinse the milk system’
‘Day counter’
‘Maintenance counter’
‘Version’
programme or find out what maintenance actions are
required.
T Select your settings for speciality coffees and hot
water.
T Disable the function "Permanently setting the amount
of water for the cup size".
T Specify whether or not to allow one-off settings during
preparation.
T Enable or disable individual products.
T Select your language.
T Select the unit for the amount of water.
T Set the time after which the WE8 should switch off
automatically.
T Change the setting for the milk system rinsing.
T You can set the water hardness of the water used.
T Keep track of all products prepared and view the
‘1 portion milk’–Milk: 3sec.–120sec.–
‘Hot water’,
‘Hot water for
green tea’
8 levelsCoffee: 15ml–80mlnormal, high
8 levelsCoffee: 25ml–240mlnormal, high
8 levelsCoffee: 30ml–160ml
8 levelsCoffee: 25ml–240ml
8 levelsCoffee: 25ml–240ml
In the programme item ‘Expert mode’ you can make individual settings for all speciality coffees and hot water. The following permanent settings can be made:
Permanent settings in programming mode always follow the same
model.
Example:Proceed as follows to change the coffee strength for one
coffee.
T Press the
T Press the
T Press the
‘Expert mode’
E Next select the button of the product for which you would like
to make settings. No product is prepared at this point.
E To display more products, press the
‘Pc’ button.
‘>’ button several times until ‘3/6’ is displayed.
‘Expert mode’ button.
‘>’ button (bottom right).
Page 23
4 Permanent settings in programming mode
T Press the ‘Coffee’ button.
‘Coffee’
T Press the ‘Coffee strength’ button.
‘Coffee’ appears and the coffee strength is displayed.
T Press the
fee strength.
T Press the
‘Saved’ appears briefly on the display.
‘Coffee’
T Press the ‘>’ button for around 2 seconds to exit program-
ming mode.
‘<’ or ‘>’ button to change the setting for the cof-
‘Save’ button.
Enable or disable setting
of cup volume
In the programme item
make the following setting:
‘Ac tiv e’: The function ‘Permanently setting the amount of
U
water for the cup size’ is activated. You can adjust the amount
of water to the cup size by pressing and holding the relevant
preparation button.
‘Inactive’: The function ‘Permanently setting the amount of
U
water for the cup size’ is deactivated. The amount of water
cannot be adjusted to the cup size by pressing and holding
the relevant preparation button.
Example:Proceed as follows to disable the function ‘Permanently
setting the amount of water for the cup size’.
T Press the
T Press the
T Press the
‘Customise cup fill volume’
T Press the ‘Inactive’ button.
T Press the
‘Saved’ appears briefly on the display.
‘3/6’
T Press the ‘>’ button to exit programming mode.
‘3/6’/ ‘Customise cup fill volume’ you can
‘Pc’ button.
‘>’ button several times until ‘3/6’ is displayed.
‘Customise cup fill volume’ button.
‘Save’ button.
23
Page 24
4 Permanent settings in programming mode
Enable or disable one-off
settings
Enable and disable
products
In the programme item ‘3/6’/ ‘One-off settings’ you can make the
following setting:
‘Ac tiv e’: One-off settings can be made during preparation (e.g.
U
coffee strength or amount of water).
‘Inactive’: One-off settings cannot be made during prepara-
U
tion. The product is prepared according to the settings in programming mode (
Example:Proceed as follows to disable one-off settings during preparation.
T Press the
T Press the
T Press the
‘One-off settings’
T Press the ‘Inactive’ button.
T Press the
‘Saved’ appears briefly on the display.
‘3/6’
T Press the ‘>’ button to exit programming mode.
In the programme item
ble each product individually.
Example:For example, you can disable the preparation of hot water.
T Press the
T Press the
T Press the
‘Lock/enable’
‘3/6’ / ‘Expert mode’).
‘Pc’ button.
‘>’ button several times until ‘3/6’ is displayed.
‘One-off settings’ button.
‘Save’ button.
‘3/6’/ ‘Lock/enable’ you can enable or disa-
‘Pc’ button.
‘>’ button several times until ‘3/6’ is displayed.
‘Lock/enable’ button.
24
E The lock symbol beside the product name indicates whether
the product is enabled or disabled. If the lock is closed, the
product is disabled.
T Press the
played.
T Press the
The lock is closed. Hot water preparation is now disabled.
T Press the
ming mode.
‘>’ button until the product ‘Hot water’ is dis-
‘Hot water’ button.
‘>’ button for around 2 seconds to exit program-
Page 25
4 Permanent settings in programming mode
Automatic switch-off
Milk system rinsing
By instructing your WE8 to automatically switch itself off, you can
cut down your energy consumption. If this function is activated,
your WE8 switches off automatically after the preset time following
the last action on the machine.
You can set the automatic switch-off to 15minutes, 30 minutes
or 1–9hours.
T Press the
T Press the
T Press the
‘Switch off after’
T Press the ‘<’ or ‘>’ button to change the switch-off time.
T Press the
‘Saved’ appears briefly on the display.
‘4/6’
T Press the ‘>’ button to exit programming mode.
In the programme item
the following settings:
‘Manual’: You are prompted to perform milk system rinsing
U
10minutes after preparation of a speciality coffee with milk.
‘Automatic’: The milk system rinsing is automatically initiated
U
10minutes after preparation of a speciality coffee with milk.
‘Pc’ button.
‘>’ button several times until ‘4/6’ is displayed.
‘Switch off after’ button.
‘Save’ button.
‘4/6’ / ‘Rinse the milk system’ you can make
Example:Proceed as follows to set the milk system rinsing to be initiated automatically 10 minutes after the preparation.
T Press the
T Press the
T Press the
‘Rinse the milk system’
T Press the ‘Automatic’ button.
T Press the
‘Saved’ appears briefly on the display.
‘4/6’
T Press the ‘>’ button to exit programming mode.
‘Pc’ button.
‘>’ button several times until ‘4/6’ is displayed.
‘Rinse the milk system’ button.
‘Save’ button.
25
Page 26
4 Permanent settings in programming mode
Setting the water
hardness
Unit for amount of water
The harder the water is, the more frequently the WE8 needs to be
descaled. It is therefore important to set the water hardness accurately.
The water hardness was set when the machine was first used. You
can change this setting at any time.
The total water hardness can be adjusted on a continuous scale
between 1°dH and 30°dH.
T Press the
T Press the
T Press the
‘Water hardness’
T Press the ‘<’ or ‘>’ button to change the setting for the
water hardness.
T Press the
‘Saved’ appears briefly on the display.
‘5/6’
T Press the ‘>’ button to exit programming mode.
Example:Proceed as follows to change the unit for the amount of
water from
T Press the
T Press the
T Press the
‘Units’
T Press the ‘oz’ button.
T Press the
‘Saved’ appears briefly on the display.
‘4/6’
T Press the ‘>’ button to exit programming mode.
‘Pc’ button.
‘>’ button several times until ‘5/6’ is displayed.
‘Water hardness’ button.
‘Save’ button.
‘ml’ to ‘oz’.
‘Pc’ button.
‘>’ button several times until ‘4/6’ is displayed.
‘Units’ button.
‘Save’ button.
Language
26
Example:Proceed as follows to change the language from
to
‘Deutsch’.
T Press the
T Press the
T Press the
‘Choose language’
‘Pc’ button.
‘>’ button several times until ‘4/6’ is displayed.
‘Choose language’ button.
‘English’
Page 27
4 Permanent settings in programming mode
E To display more languages, press the ‘> ’ button (bottom
right).
T Press the button that corresponds to the language you want,
e.g.
‘Deutsch’.
‘Gespeichert’ appears briefly on the display.
‘4/6’
T Press the ‘>’ button to exit programming mode.
Query counter readings
and version
In the programme item
‘Product counter’: Number of prepared speciality coffees and
U
hot water
‘Day counter’: Number of prepared speciality coffees and hot
U
water. This counter can be reset to zero
‘Maintenance counter’: Number of maintenance programmes
U
performed (cleaning, descaling etc.)
‘Version’: Software version
U
Example:Proceed as follows to reset the day counter.
T Press the
T Press the
T Press the
T Press the
‘Delete the day counter?’
T Press the ‘Yes’ button.
‘Saved’ appears briefly on the display.
‘6/6’
T Press the ‘>’ button to exit programming mode.
‘6/6’ you can view the following information.
‘Pc’ button.
‘>’ button several times until ‘6/6’ is displayed.
‘Day counter’ button.
‘>’ button.
27
Page 28
5 Maintenance
5 Maintenance
Your WE8 has the following integrated maintenance programmes:
Rinsing the machine (‘Rinse the coffee system’)
U
Rinsing the fine foam frother (‘Rinse the milk system’)
U
Cleaning the fine foam frother (‘Clean the milk system’)
U
Changing the filter (‘Filter’)
U
Cleaning the machine (‘Clean’)
U
Descaling the machine (‘Descale’)
U
E Carry out each maintenance programme when you are
prompted to do so.
E Press the
grammes. When the bar is completely filled with red, your
WE8 will prompt you to perform the appropriate maintenance
programme.
‘Pc’ button to view a list of the maintenance pro-
Rinsing the machine
Rinsing the milk system
You can start coffee system rinsing manually at any time.
T Place a receptacle under the coffee spout.
T Press the
T Press the
T Press the
operation.
‘Machine is rinsing’, water flows out of the coffee spout. The
operation stops automatically.
After each milk preparation, the WE8 prompts you to perform a milk
system rinse.
E In programming mode, you can set whether the milk system
rinsing is to be prompted 10 minutes after preparation or initiated automatically (see Chapter 4 ‘Permanent settings in programming mode – Milk system rinsing’).
‘Pc’ button.
‘>’ button.
‘Rinse the coffee system’ button to start the rinse
28
Page 29
Precondition:‘Rinse the milk system’ is displayed.
T Place a receptacle under the fine foam frother.
T Press the
‘Pc’ button.
‘Milk system is being rinsed’ appears and the fine foam
frother is rinsed.
The operation stops automatically.
5 Maintenance
Cleaning the fine foam
frother
CAUTION
6
To ensure that the fine foam frother always works properly, you
must clean it daily when you have been preparing milk.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
E JURA milk system cleaner is available from specialised dealers.E To clean the milk system, use the container supplied.
T Press the
T Press the
‘Pc’ button.
‘Clean the milk system’ button.
‘Clean the milk system’
T Press the ‘Start’ button.
T Press the
‘Next’ button.
‘Clean the milk system’ / ‘Milk system cleaner’
T Remove the milk pipe from the milk container or milk cooler.
T Add milk system cleaner to the front part of the container
up to the bottom mark (indicated by 6).
T Then fill with water up to the upper mark.
T Place the container under the fine foam frother.
29
Page 30
5 Maintenance
T Connect the milk pipe to the container.
E To connect the milk pipe to the container correctly, the pipe
must be fitted with a connector.
6
Dismantling and rinsing
the fine foam frother
1
2
T Press the
‘Next’ button.
‘Milk system is being cleaned’ appears and the fine foam
frother and the milk pipe are cleaned.
‘Clean the milk system’ / ‘Fresh water’
T Rinse the container thoroughly and fill the front part with
fresh water up to the upper mark.
T Place this under the fine foam frother and reconnect the
milk pipe to the container.
T Press the
‘Next’ button.
‘Milk system is being cleaned’ appears and the fine foam
frother and the milk pipe are rinsed with fresh water.
The operation stops automatically.
To make sure the fine foam frother works properly, and in the interests of hygiene, it must be dismantled and rinsed daily if you have
been preparing milk.
T Remove the milk pipe and rinse it thoroughly under running
water.
T Remove the fine foam frother.
30
T Dismantle the fine foam frother into its individual parts.
T Rinse all the parts under running water. If there are severely
dried-on milk residues, firstly immerse the individual parts
in a solution of 250ml cold water and 1 capful of JURA milk
system cleaner. Then rinse the parts thoroughly.
Page 31
5 Maintenance
T Re-assemble the fine foam frother.
E Ensure that all individual parts are correctly and firmly con-
nected to ensure optimum operation.
T Re-fit the fine foam frother on the milk system.
Inserting/changing the
filter
Your WE8 no longer has to be descaled if you are using the CLARIS
Pro Smart filter cartridge.
E Once the filter cartridge stops working (depending on the
water hardness setting), the WE8 will prompt you to change
the filter.
E CLARIS Pro Smart filter cartridges are available from special-
ised dealers.
Precondition:The start screen is displayed. The filter symbol lights
up red (if you are already using a filter).
T Remove and empty the water tank.
T Open the filter holder.
T Insert a new CLARIS filter cartridge Pro Smart into the water
tank, exerting slight pressure.
T Close the filter holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
E The machine automatically detect s that you have just inserted/
changed the filter cartridge.
‘Saved’ appears briefly on the display.
31
Page 32
5 Maintenance
‘Filter is beingrinsed’, the filter is rinsed. The water flows
directly into the drip tray.
Rinsing of the filter stops automatically. The start screen is
displayed.
E If the filter is active, this is indicated by a blue filter symbol at
the bottom of the display.
Cleaning the machine
CAUTION
After 180preparations or 80switch-on rinses, the WE8 will prompt
you to clean it.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
E The cleaning programme lasts approximately 20 minutes.E Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
E JURA cleaning tablets are available from specialised dealers.
Precondition:
T Press the
T Press the
T Press the
T Empty the drip tray and coffee grounds container and put
T Place one receptacle under the coffee spout and another
T Press the
T Open the cover of the filler funnel for ground coffee.
‘Clean machine’ is displayed.
‘Pc’ button (red Maintenance symbol).
‘Start’ button.
‘Next’ button.
‘Empty coffee grounds container’
them back into the machine.
‘Clean’
under the fine foam frother.
‘Next’ button.
‘Machine is being cleaned’, water flows out of the coffee
spout.
The operation is interrupted,
‘Add cleaning tablet’.
32
Page 33
5 Maintenance
T Insert a JURA cleaning tablet into the filler funnel.
T Close the cover of the filler funnel.
T Press the
‘Next’ button.
‘Machine is being cleaned’, water flows repeatedly out of the
coffee spout and the fine foam frother.
The operation stops automatically.
‘Empty coffee grounds container’
T Empty the drip tray and coffee grounds container and put
them back into the machine.
Cleaning is now complete.
Descaling the machine
J
CAUTION
CAUTION
CAUTION
CAUTION
The WE8 builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the hardness of your water.
E If you are using a CLARIS Pro Smart filter cartridge, you will not
be prompted to descale.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
T Avoid contact with the skin or eyes.
T Rinse off the descaling agent with clean water. Should you get
any descaling agent in your eye, see a doctor.
If the wrong descaling agent is used, the machine could be damaged and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling programme to run to the end.
If the descaling agent comes into contact with sensitive surfaces
(e.g. marble), damage cannot be ruled out.
T Clean up any splashes immediately.
E The descaling programme lasts approximately 40minutes.E JURA descaling tablets are available from specialised dealers.
33
Page 34
5 Maintenance
3x
Precondition:‘Decalcify machine’ is displayed.
T Press the
T Press the
T Press the
‘Pc’ button (red Maintenance symbol).
‘Start’ button.
‘Next’ button.
‘Empty drip tray’
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Agent in tank’
T Remove and empty the water tank.
T Completely dissolve 3JURA descaling tablets in a receptacle
holding 500ml of water. This may take several minutes.
T Pour the solution into the empty water tank and insert it
into the machine.
T Place a receptacle under the fine foam frother.
T Press the
‘Next’ button.
‘Machine is being descaled’appears and water flows out of
the fine foam frother repeatedly.
The operation is interrupted,
‘Empty drip tray’.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
‘Fill water tank’
T Remove the water tank and rinse it thoroughly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Place one receptacle under the coffee spout and another
under the fine foam frother.
T Press the
‘Next’ button.
‘Machine is being descaled’, the descaling operation is con-
tinued.
The operation is interrupted,
‘Empty drip tray’.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
Descaling is now complete.
34
E If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
Page 35
5 Maintenance
Cleaning the bean
container
Descaling the water tank
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container. These traces may negatively affect
the coffee result. For this reason clean the bean container from time
to time.
Precondition:
T Switch the machine off with the On/Off button Q.
T Remove the aroma preservation cover.
T Clean the bean container with a soft, dry cloth.
T Fill the bean container with coffee beans and close the
Limescale deposits may form in the water tank. To ensure correct
function of the machine, descale the water tank from time to time.
T Remove the water tank.
T If you use a CLARIS Pro Smart filter cartridge, remove this.
T Completely fill the water tank and dissolve 3 JURA descaling
T Leave the water tank with the descaling solution for several
T Empty the water tank and rinse it thoroughly.
T If you use a CLARIS Pro Smart filter cartridge, insert this
T Fill the water tank with fresh, cold water and reinsert the
‘Fill bean container’ is displayed.
aroma preservation cover.
tablets in it.
hours (e.g. overnight).
again.
tank.
35
Page 36
6 Display messages
6 Display messages
MessageCause/ResultAction
‘Fill water tank’The water tank is empty. You
cannot prepare any products.
‘Empty coffee
grounds
container’
‘Drip tray not
fitted’
‘Fill bean
container’
‘Rinse the milk
system’
The filter symbol
at the bottom of
the display lights
up red.
‘Clean machine’The WE8 is prompting you to
‘Decalcify
machine’
‘Too hot’The system is too hot to start
The coffee grounds container
is full. You cannot prepare any
products.
The drip tray is not inserted
correctly or is not inserted at all.
You cannot prepare any products.
The bean container is empty.
You cannot prepare any speciality
coffees, but you can prepare hot
water and milk.
The WE8 requests a milk system
rinse.
The filter cartridge no longer
works.
clean it.
The WE8 is prompting you to
descale it.
a maintenance programme.
T Fill the water tank (see Chapter 3
‘Daily operation – Filling the water
tank’).
T Empty the coffee grounds container
and the drip tray (see Chapter 3
‘Daily operation – Daily maintenance’).
T Fit the drip tray.
T Fill the bean container (see Chapter 1
‘Preparing and using for the first
time – Filling the bean container’).
T Perform milk system rinsing (see
Chapter 5 ‘Maintenance – Rinsing the
milk system’).
T Replace the CLARIS Pro Smart filter
cartridge (see Chapter 5 ‘Maintenance – Inserting/changing the filter’).
T Perform cleaning (see Chapter 5
‘Maintenance – Cleaning the machine’).
T Perform descaling (see Chapter 5
‘Maintenance – Descaling the
machine’).
T Wait for several minutes until the
system has cooled or prepare a
speciality coffee or hot water.
36
Page 37
7 Troubleshooting
ProblemCause/ResultAction
Insufficient foam is
produced when the milk
is frothed or milk sprays
out of the fine foam
frother.
Coffee only comes out
in drips when it is being
prepared.
‘Fill water tank’ is
displayed although the
water tank is full.
Grinder is making a very
loud noise.
‘ERROR2’ or ‘ERROR5’
is displayed.
Other
‘ERROR’ messages
are displayed.
The fine foam frother is
dirty.
The coffee is ground too
finely and obstructs the
system.
The water tank float is
trapped.
There are foreign
objects in the grinder.
If the machine has been
exposed to the cold for
a long period of time,
heating may be disabled
for safety reasons.
–
T Clean the fine foam frother (see
Chapter 5 ‘Maintenance – Cleaning the
fine foam frother’).
T Dismantle and rinse the fine foam
frother (see Chapter 5 ‘Maintenance –
Dismantling and rinsing the fine foam
frother’).
T Set the grinder to a coarser setting
(see Chapter 2 ‘Preparation – Adjusting
the grinder’).
T Descale the water tank (see Chapter 5
‘Maintenance – Descaling the water
tank’).
T Contact customer support in your
country (see Chapter 11 ‘JURA contact
details/ Legal information’).
T Warm the machine at room temperature.
T Switch the WE8 off with the On/Off
button Q. Contact customer support in
your country (see Chapter 11 ‘JURA
contact details/ Legal information’).
7 Troubleshooting
E If you were unable to solve the problem, contact customer
support in your country (see Chapter 11 ‘JURA contact details/
Legal information’).
37
Page 38
8 Transport and environmentally friendly disposal
8 Transport and environmentally friendly disposal
Transport/ Emptying the
system
Disposal
Keep the packaging for your WE8. It should be used to protect the
machine during transport.
In order to protect the WE8 from frost during transport, the system
must be emptied.
Precondition:The start screen (
T Remove the milk pipe from the fine foam frother.
T Place a receptacle under the fine foam frother.
T Press the
‘1 portion milk’, hot steam is discharged from the fine foam
frother.
T Remove and empty the water tank.
T Press the
‘Amount of milk’ / ‘60sec.’ is displayed.
Steam will continue to be discharged from the fine foam
frother until the system is empty.
‘Fill water tank’
T Press the On/Off button Q.
Your WE8 is switched off.
Please dispose of old machines in an environmentally neutral way.
H
Old machines contain valuable, recyclable materials which should
be recycled. Please therefore dispose of old machines via suitable
collection systems.
Holding capacity of water
tank (without filter)
Holding capacity of bean
container
Holding capacity of coffee
grounds container
Cable lengthapprox. 1.1m
Weightapprox. 10.0kg
Dimensions (WHD)approx. 29.5 41.9 44.4cm
Milk system HP3
Information for testers (repeat test in accordance with DIN VDE
0701-0702): The central grounding point (CGP) is located on the
underside of the machine, right next to the mains cable's connection point.
A
3l
500g
max. 25 portions
39
Page 40
10 Index
10 Index
A
Addresses 44
Adjusting the product settings 22
Aroma preservation cover
Cleaning the fine foam frother 29
Fine foam frother 4
Rinsing 28
Milk system rinsing 25
N
Number
Maintenance programmes 27
Preparations 27
P
Permanently setting the water for
the cup size 17
Permanent settings in programming
mode 21
Preparation 14
Cappuccino 14
Coffee 15
Espresso 15
Espresso doppio 15
Flat white 14
Green tea 18
Ground coffee 16
Hot water 18
Latte macchiato 14
Milk foam 16
Ristretto 15
Two coffees 15
Two espressi 15
Two ristretti 15
Two speciality coffees 15
Problems
Troubleshooting 37
Product counter 27
Products
Disable 24
Enable 24
Product settings
Adjusting 22
Professional fine foam frother 5
41
Page 42
10 Index
Programming mode 21
Automatic switch-off 25
Counter readings and version 27
Enable or disable setting of
cup volume 23
Language 26
Milk system rinsing 25
One-off settings 24
Setting the water hardness 26
Unit for amount of water 26
Proper use 6
R
Regular maintenance 20
Rinsing
Machine 28
Ristretto 15
Two ristretti 15
S
Safety 6
Safety information 6
Service socket 5
Settings
Permanent settings in programming
mode 21
Setting up
Setting up the machine 10
Short operating instructions 10
Smart Connect 5, 13
Switching off 20
Switching on 19
Switch-off
Automatic switch-off 25
Symbol description 3
T
Technical data 39
Milk system 39
Tel 44
Transport 38
Troubleshooting 37
Two products 15
U
Unit for amount of water 26
Use, First-time 11
V
Version 27
W
Water hardness
Determining the water hardness 10
Setting the water hardness 26
The machine complies with the following directives:
2006/42/EC– Machinery Directive
U
2014/30/EU– Electromagnetic Compatibility
U
2009/125/EC– Ecodesign Directive
U
2011/65/EU– RoHS Directive
U
We reserve the right to make technical changes. The diagrams used
in these instructions for use are for illustration purposes only and do
not represent the original colours of the machine. Some details of
your WE8 may vary.
Your opinion is important to us! Use the contact details at
www.jura.com.
The instructions for use contain information which is protected by
copyright. It is not permitted to photocopy these instructions for use
or translate them into another language without the prior written
consent of JURA Elektroapparate AG.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.