JURA WE8 User Manual

Download

WE8 Instructions for Use

Original instructions for use

Before using the machine read the instructions for use.

JURA Type 737

Table of contents

Your WE8

Control elements 4

Important information 6

Proper use ......................................................................................................................................................6

For your safety ...............................................................................................................................................6

1 Preparing and using for the first time 10

JURA on the Internet ....................................................................................................................................10

Setting up the machine ..............................................................................................................................10

Filling the bean container ...........................................................................................................................10

Determining the water hardness ..............................................................................................................10

First-time use .................................................................................................................................................11

Connecting milk ...........................................................................................................................................14

2 Preparation 15

Latte macchiato, cappuccino and other speciality coffees with milk .................................................15

Ristretto, espresso and coffee ....................................................................................................................16

Two ristretti, two espressi and two coffees .............................................................................................16

Milk foam .......................................................................................................................................................17

Ground coffee ............................................................................................................................................... 17

Permanently setting the amount of water for the cup size .................................................................18

Adjusting the grinder ..................................................................................................................................19

Hot water .......................................................................................................................................................19

3 Daily operation 20

Filling the water tank ..................................................................................................................................20

Switching on the machine .........................................................................................................................20

Daily maintenance .......................................................................................................................................21

Regular maintenance ..................................................................................................................................21

Switching off the machine .........................................................................................................................22

4 Permanent settings in programming mode 23

Adjusting the product settings .................................................................................................................24

Enable or disable setting of cup volume ................................................................................................25

Enable or disable one-off settings ...........................................................................................................25

Enable and disable products .....................................................................................................................26

Automatic switch-off ..................................................................................................................................26

Milk system rinsing .....................................................................................................................................27

Setting the water hardness .......................................................................................................................27

Unit for amount of water ...........................................................................................................................28

Language ......................................................................................................................................................28

Query counter readings and version .......................................................................................................29

Table of contents

5 Maintenance 30

Rinsing the machine ...................................................................................................................................30

Rinsing the milk system ............................................................................................................................. 30

Cleaning the milk system ...........................................................................................................................31

Dismantling and rinsing the fine foam frother......................................................................................32

Dismantling and rinsing the professional fine foam frother ............................................................... 32

Inserting the filter .......................................................................................................................................33

Changing the filter ......................................................................................................................................34

Cleaning the machine ................................................................................................................................34

Descaling the machine .............................................................................................................................. 35

Cleaning the bean container .....................................................................................................................37

Descaling the water tank ........................................................................................................................... 37

6 Display messages 38

7 Troubleshooting 39

8 Transport and environmentally friendly disposal 41

Transport/ Emptying the system ..............................................................................................................41

Disposal ..........................................................................................................................................................41

9 Technical data 42

10 Index 43

11 JURA contact details/ Legal information 48

Symbol description

Warnings

J WARNING

J CAUTION

CAUTION CAUTION draws your attention to potential damage to the machine.

Symbols used

‘Coffee’ Display

Always take note of any information marked with the words CAUTION or WARNING and a warning sign. The signal word WARNING draws your attention to potential serious injury, and the signal word CAUTION to potential minor injury.

Prompt to take action. This symbol means that you are being prompted to perform some action.

Information and tips to make it even easier to use your JURA.

Control elements

3 4 5

1 Filler funnel cover 2 Filler funnel for ground coffee 3 Bean container with aroma

preservation cover 4 Water tank cover 5 Water tank 6 Plug-in mains cable 

(back of the machine) 7 Coffee grounds container 8 Drip tray

9 Cover cap for grinder adjustment switch 10 Grinder adjustment switch 11 On/Off button Q 12 Fine foam frother 13 Height-adjustable coffee spout 14 Cup grille

1 Display 2 Multi-function buttons (button function depends

on what is shown in the display)

Professional fine foam frother (optional)

Control elements

Accessories

Container for milk system cleaning

Measuring spoon for ground coffee

Hot-water nozzle

Important information

Proper use

For your safety

This machine is intended for use by specialist or trained staff in businesses, light industry and agricultural facilities or for commercial use by non-professionals. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use.

Before using the machine read these instructions for use thoroughly and completely and comply with the instructions they contain. A warranty service is not applicable for damage or defects caused by non-compliance with the instructions for use. Keep these instructions for use close to the machine and pass them on to the next user.

The JURA may only be operated by instructed persons. Non-professionals must be supervised during use.

Please carefully read and observe the important safety information set out below.

To avoid danger of potentially fatal electric shock:

Never use a machine which is damaged or has

a defective mains cable. In the event of signs of damage, for example if

there is a smell of burning, unplug the machine immediately from the mains supply and contact JURA service. If the mains cable of this machine is damaged

it must be replaced with a special mains cable,

Important information

which is available directly from JURA or from authorised JURA service centres. Make sure that the JURA and the mains cable

are not located close to hot surfaces. Be careful to ensure that the mains cable is not

trapped and does not rub against sharp edges. Never open and repair the machine yourself.

Do not modify the machine in any way that is not described in these instructions for use. The machine contains live parts. If opened, there is a danger of potentially fatal injury. Repairs may only be carried out by authorised JURA service centres, using original spare parts and accessories. To completely and safely disconnect the

machine from the power supply, first switch off the JURA using the On/Off button. Only then should you remove the mains plug from the power socket.

There is a risk of scalds or burns on the spouts and fine foam frother:

Place the machine out of the reach of children.

Do not touch any hot parts. Use the handles

provided. Be careful to ensure that the fine foam frother

is correctly installed and clean. If incorrectly fitted or if it becomes blocked, the fine foam frother or its parts might come off.

A defective machine is not safe and could cause injury or fire. To avoid damage and any associated risk of injury or fire:

Never allow the mains cable to loosely hang

down. The mains cable could pose a tripping hazard or become damaged.

Important information

Protect the JURA from environmental influ-

ences such as rain, frost and direct sunlight. Do not immerse the JURA, mains cable or con-

nections in water. Do not put the JURA or any individual parts in

the dishwasher. Before cleaning, switch the JURA off with the

On/Off button. Always wipe the JURA with a damp cloth rather than a wet one, and protect it from prolonged exposure to water splash. Only connect the machine to the mains volt-

age in accordance with the information on the rating plate. The rating plate is located on the underside of your JURA. Further technical data is provided in these instructions for use (see Chapter 9 ‘Technical data’). Connect the JURA directly to a domestic power

socket. Using multi-socket adapters or extension cords may cause overheating. Please only use original JURA maintenance

products. Use of products that are not explicitly recommended by JURA could damage the machine. Do not use alkaline cleaning agents when

cleaning, use a soft cloth and a mild detergent. Do not use any coffee beans treated with addi-

tives or caramelised coffee beans. Only fill the water tank with fresh, cold water.

Switch the machine off with the On/Off button

if you are going to be absent for a longer period of time and remove the mains plug from the power socket. Children may not clean or service the machine

unless supervised by a responsible person.

Important information

Do not allow children to play with the machine.

Keep children under the age of 8 away from

the machine, or supervise them constantly. Children aged 8 and over may only operate

the machine without supervision if they have been instructed in how to use it safely. Children must be able to recognise and understand the potential dangers arising from incorrect use.

People, including children, who

do not have the physical, sensory or mental

capabilities to use the machine safely or are inexperienced or lack knowledge in how to

use the machine safely must be supervised by a responsible person when using it, or must be instructed in how to use it correctly.

Safety when handling the CLARIS Pro Smart filter cartridge:

Filter cartridges should be kept out of the

reach of children.

Store filter cartridges in a dry place in the

sealed packaging.

Protect cartridges from heat and direct

sunlight.

Do not use damaged filter cartridges.

Do not open filter cartridges.

1 Preparing and using for the first time

JURA on the Internet

Setting up the machine

Filling the bean container

CAUTION

Visit us on the Internet. You can download short operating instructions for your machine from the JURA website (www.jura.com). You

will also find interesting and up-to-date information on your JURA and on every aspect of coffee.

When setting up your JURA, please note the following:

Place the JURA on a horizontal surface that is not sensitive to

water.

Choose a spot for your JURA which protects the machine

against overheating. Ensure that the ventilation slots are not

covered.

Coffee beans which have been treated with additives (e.g. sugar), ground coffee or freeze-dried coffee will damage the grinder.

T Only use roasted, untreated coffee beans to fill the bean con-

tainer.

Determining the water hardness

T Remove the aroma preservation cover.

T Remove any dirt or foreign objects from inside the bean

container.

T Fill the bean container with coffee beans and close the

aroma preservation cover.

When you use the machine for the first time, you must set the water hardness. If you do not know the hardness of your water, you can find this out first. Use the Aquadur machine.

T Hold the test strip briefly (for 1second) under flowing water.

Shake off the water.

T Wait for about 1minute.

test strips supplied with the

1 Preparing and using for the first time

T You will then be able to read the degree of water hardness

from the discolouration of the Aquadur® test strip and the description on the packaging.

First-time use

WARNING

When using the machine for the first time, you can choose whether you want to operate JURA with or without the CLARIS Pro Smart filter cartridge. If the water hardness is 10 °dH or more (total hardness), we recommend using the filter cartridge.

If the machine is operated with a defective mains cable, there is a danger of potentially fatal electric shock.

T Never use a machine which is damaged or has a defective

mains cable.

Precondition:The bean container has been filled.

T Connect the mains cable to the machine.

T Insert the mains plug into a power socket.

T Press the On/Off button Q to switch the JURA on.

‘Sprachauswahl’

E To display more languages, press the ‘ > ’ button (bottom

right).

T Press the button that corresponds to the language you want,

e.g.

‘English’. ‘Saved’ appears briefly on the display to confirm the setting. ‘Water hardness’

E If you do not know the hardness of your water, you must find

this out first (see Chapter 1 ‘Preparing and using for the first time – Determining the water hardness’).

T Press the

setting, for example to

‘<’ or ‘>’ button to change the water hardness

‘25°dH’.

1 Preparing and using for the first time

First-time use with filter

cartridge activation

T Press the ‘Save’ button.

‘Saved’ appears briefly on the display. ‘Use filter’

E Now decide whether you want to operate your JURA with or

without a CLARIS Pro Smart filter cartridge.

Operation with filter cartridge: go straight to the next section (see Chapter 1 ‘Preparing and using for the first time – First-time use with filter cartridge activation’).

Operation without filter cartridge (see Chapter 1 ‘Preparing and using for the first time – First-time use without filter cartridge activation’).

CAUTION

Milk, sparkling mineral water or other liquids can damage the water tank or the machine.

T Only fill the water tank with fresh, cold water.

T Place a receptacle (at least 300 ml) under the fine foam

frother and the coffee spout.

T Remove the water tank and rinse it with cold water. T Open the filter holder.

T Insert the filter cartridge into the water tank. T Close the filter holder. It will click into place audibly. T Fill the water tank with fresh, cold water and reinsert the

tank.

E The machine automatically detects that you have just inserted

the filter cartridge.

‘Use filter’ / ‘Saved’ ‘Filter is being rinsed’

, water flows out of the fine foam frother. Rinsing of the filter stops automatically after approximately 300ml.

First-time use without filter

cartridge activation

1 Preparing and using for the first time

‘System is filling’, the system fills up with water. ‘Empty drip tray’

T Empty the drip tray and coffee grounds container and put

them back into the machine.

‘Machine is rinsing’, the system is rinsed.

The rinse stops automatically. Your JURA is ready for use.

E The start screen shows the products you can prepare. Press

the

‘>’ button to display more products.

E If the filter is active, this is indicated by a blue filter symbol at

the bottom of the display.

CAUTION

Milk, sparkling mineral water or other liquids can damage the water tank or the machine.

T Only fill the water tank with fresh, cold water.

T Press the

‘No filter’ button. ‘Saved’ appears briefly on the display. ‘Fill water tank’

T Place one receptacle under the coffee spout and another

under the fine foam frother.

T Remove the water tank and rinse it with cold water. T Fill the water tank with fresh, cold water and reinsert the

tank.

‘System is filling’, the system fills up with water. ‘Machine is heating’ ‘Machine is rinsing’

, the system is rinsed.

The rinse stops automatically. Your JURA is ready for use.

E The start screen shows the products you can prepare. Press

the

‘>’ button to display more products.

1 Preparing and using for the first time

Connecting milk

Your JURA creates fine, creamy, feather-light milk foam with a perfect consistency. The most important requirement for frothing milk is a milk temperature of 4–8°C. We would therefore recommend using a milk cooler or a vacuum milk container.

T Remove the protective cover from the fine foam frother.

T Connect the milk pipe to the fine foam frother. T Connect the other end of the milk pipe to a milk container

or a milk cooler.

2 Preparation

E The display shows four products you can prepare. Press the

‘>’ button to display more products.

E You can stop the machine at any time while a speciality coffee

or hot water is being prepared. To do this, press the button.

E During the grinding operation you can select the coffee

strength of single products by pressing the tons.

E During preparation you can change the preset amounts (e.g.

water and amount of milk) by pressing the tons.

Coffee tastes best served hot. A cold porcelain cup cools the beverage – and impairs the taste. We therefore recommend prewarming the cups. The full coffee aroma can develop only in prewarmed cups. You can purchase a JURA cup warmer from your specialised dealer.

You can make permanent settings for all products in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Adjusting the product settings’).

‘<’ and ‘>’ but-

‘Cancel’

Latte macchiato, cappuccino and other speciality coffees with milk

Your JURA prepares latte macchiato, cappuccino and flat white at the touch of a button. There is no need to move the glass or cup.

E This chapter applies to the professional fine foam frother and

the fine foam frother.

Example:Proceed as follows to prepare one latte macchiato. Precondition:Milk is connected to the fine foam frother.

T Place a glass under the fine foam frother.

E If you are using the professional fine foam frother, turn the

setting wheel to the Milk Foam positioné.

T Press the

‘Latte macchiato’, the preset amount of milk foam flow into

the glass.

‘Latte macchiato’ button.

2 Preparation

Ristretto, espresso and coffee

E There is a short interval while the hot milk separates from the

milk foam. This allows the typical layers of a latte macchiato to form. You can choose the length of this interval in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Adjusting the product settings’).

Coffee preparation starts. The preset amount of water for espresso flows into the glass. Preparation stops automatically. Your JURA is once more ready for use.

To ensure that the fine foam frother always works properly, you must clean it daily when you have been preparing milk (see Chap- ter 5 ‘Maintenance – Cleaning the milk system’).

Example:Proceed as follows to prepare one coffee.

T Place a cup under the coffee spout. T Press the

Preparation starts. played. The preset amount of water for coffee flows into the cup. Preparation stops automatically. Your JURA is once more ready for use.

‘Coffee’ button.

‘Coffee’ and the coffee strength are dis-

Two ristretti, two espressi and two coffees

To prepare two speciality coffees, press the appropriate preparation button twice (within approximately 1 second).

Example:Proceed as follows to prepare two espressi.

T Place two cups under the coffee spout. T Press the

preparation.

‘2 espressi’, the preset amount of water flows into the cups.

Preparation stops automatically. Your JURA is once more ready for use.

‘Espresso’ button twice (within 1 second) to start

2 Preparation

Milk foam

Ground coffee

E This chapter applies to the professional fine foam frother and

the fine foam frother.

Precondition:Milk is connected to the fine foam frother.

T Place a cup under the fine foam frother.

E If you are using the professional fine foam frother, turn the

setting wheel to the Milk Foam positioné.

E If you want to prepare hot milk, turn the setting wheel of the

professional fine foam frother to the Milk position è.

T Press the

‘Milk foam’, the milk foam is prepared. The preset amount

flows into the cup. Preparation stops automatically. Your JURA is once more ready for use.

To ensure that the fine foam frother always works properly, you must clean it daily when you have been preparing milk (see Chap- ter 5 ‘Maintenance – Cleaning the milk system’).

You can choose to use a second coffee variety, for example decaffeinated coffee, with the filter funnel for ground coffee.

E Never add more than two level measuring spoons of ground

coffee.

E Use ground coffee which is not ground too finely. Very fine

coffee can block up the system so that the coffee only comes out in drips.

E If you did not fill the machine with a sufficient amount of

ground coffee, the JURA stops the operation.

E The desired speciality coffee must be prepared within approx-

imately one minute after filling with the ground coffee. Otherwise the JURA stops the operation and is once more ready for use.

‘Milk foam’ button.

‘Not enough ground coffee’ is displayed and

All speciality coffees with ground coffee are always prepared following the same model.

2 Preparation

Example:Proceed as follows to prepare one espresso using ground

coffee.

T Place a cup under the coffee spout. T Open the powder chute cover.

‘Ground coffee’ / ‘Please add ground coffee’

T Place one level measuring spoon of ground coffee into the

filler funnel.

T Close the cover of the filler funnel. T Press the

Preparation starts. espresso flows into the cup. Preparation stops automatically. Your JURA is once more ready for use.

‘Espresso’ button.

‘Espresso’, the preset amount of water for

Permanently setting the amount of water for the cup size

It is easy to permanently adjust the amount of water for all single products to the cup size. Adjust the amount once as shown in the

following example. Every time you prepare a drink in the future, this amount will be dispensed.

Example:Proceed as follows to permanently set the amount of water for one coffee.

T Place a cup under the coffee spout. T Press and hold the

Press button’

T Release the

Preparation starts and the coffee flows into the cup.

T Press any button except

coffee in the cup. Preparation stops. set amount of water for one coffee is permanently stored. Your JURA is once more ready for use.

E You can alter this setting at any time by repeating the above

procedure.

E You can also permanently set the amounts for all single prod-

ucts in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Adjusting the product settings’).

‘Coffee’ button.

‘Coffee’ button until ‘Enough coffee?

appears.

‘Cancel’ as soon as there is sufficient

‘Saved’ appears briefly on the display. The

2 Preparation

Adjusting the grinder

CAUTION

You can adjust the grinder on a continuous scale to suit the degree of roast of your coffee.

If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged.

T Only adjust the consistency of grind when the grinder is run-

ning.

The consistency of grind is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms.

Example:Proceed as follows to change the consistency of grind during the preparation of an espresso.

T Place a cup under the coffee spout. T Open the cover of the grinder adjustment switch. T Press the T Turn the grinder adjustment switch to the desired position

while the grinder is running. The preset amount of water flows into the cup. Preparation stops automatically.

T Close the cover of the grinder adjustment switch.

‘Espresso’ button to start preparation.

Hot water

CAUTION

To obtain a perfect water flow, use the hot-water nozzle.

There is a danger of scalding from hot water splashes.

T Avoid direct contact with the skin.

T Place a cup under the hot-water nozzle. T Press the

‘Hot water’, the preset amount of water flows into the cup.

Preparation stops automatically. Your JURA is once more ready for use.

‘Hot water’ button.

3 Daily operation

Filling the water tank

CAUTION

Switching on the machine

Daily maintenance of the machine and hygiene when handling coffee and water are key to a perfect coffee result in the cup every time. You should therefore change the water daily.

Milk, sparkling mineral water or other liquids can damage the water tank or the machine.

T Only fill the water tank with fresh, cold water.

T Open the water tank cover. T Remove the water tank and rinse it with cold water. T Fill the water tank with fresh, cold water and reinsert the

tank.

T Close the water tank cover.

T Place a receptacle under the coffee spout. T Press the On/Off button Q to switch the JURA on.

‘Welcome to JURA’ ‘Machine is rinsing’

automatically. The start screen is displayed. Your JURA is ready for use.

, the system is rinsed. The rinse stops

3 Daily operation

Daily maintenance

Regular maintenance

To ensure that you get many years of reliable service out of your JURA and to guarantee the optimum coffee quality, the machine requires daily maintenance.

T Pull out the drip tray. T Empty the coffee grounds container and the drip tray. Rinse

them both with warm water.

E Always empty the coffee grounds container when the machine

is switched on. This is the only way of resetting the coffee grounds counter.

T Refit the coffee grounds container and the drip tray. T Rinse the water tank with clean water. T Clean the fine foam frother (see Chapter 5 ‘Maintenance –

Cleaning the milk system’).

T Remove the milk pipe and rinse it thoroughly under running

water.

T Dismantle and rinse the fine foam frother (see Chapter 5

‘Maintenance – Dismantling and rinsing the fine foam frother’).

T Wipe the surface of the machine with a clean, soft, damp

cloth (e.g. microfibre cloth).

Carry out the following maintenance actions regularly or as

required:

In the interests of hygiene, we recommend changing the milk

pipe and interchangeable milk spout on a regular basis (approximately every 3 months). Replacements are available from specialised dealers. Clean the inside of the water tank, e.g. with a brush. Further

information about the water tank is provided in these instructions for use (see Chapter 5 ‘Maintenance – Descaling the water tank’). Traces of milk and coffee may stick to the top and bottom of

the cup grille. If this happens, clean the cup grille.

3 Daily operation

Switching off the machine

When the JURA is switched off, the system is automatically rinsed if a speciality coffee has been prepared.

T Place one receptacle under the coffee spout and another

under the fine foam frother.

T Press the On/Off button Q.

E If milk has been prepared, you will be prompted to clean the

milk system ( switch-off process continues automatically.

E If milk has been prepared but you have not started milk sys-

tem cleaning, the milk system is rinsed first (

being rinsed’

‘Machine is rinsing’, the system rinses itself. The operation

stops automatically. Your JURA is switched off.

‘Clean the milk system’). After 10 seconds the

‘Milk system is

4 Permanent settings in programming mode

Press the ‘Pc’ button to enter programming mode. You can navigate through the programme items and permanently save the required settings using the multi-function buttons. The following settings can be made:

Programme item

‘1/6’ ‘Clean’,

‘2/6’ ‘Rinse the milk system’,

‘3/6’ ‘Expert mode’

‘4/6’ ‘Choose language’

‘5/6’ ‘Water hardness’

‘6/6’ ‘Product counter’,

Sub-item Explanation

T Start the required maintenance programme here.

‘Descale’, ‘Clean the milk system’, ‘Filter’ (only if filter is

activated)

T Here you can start the required maintenance

‘Rinse the coffee system’, ‘Information’

‘Customise cup fill volume’

‘One-off settings’

‘Lock/enable’

‘Units’

‘Switch off after’

‘Rinse the milk system’

‘Day counter’, ‘Maintenance counter’, ‘Version’

programme or find out what maintenance actions are required.

T Select your settings for speciality coffees and hot water.

T Disable the function "Permanently setting the amount of water for the cup size".

T Specify whether or not to allow one-off settings during preparation.

T Enable or disable individual products. T Select your language. T Select the unit for the amount of water. T Set the time after which the JURA should switch

off automatically.

T Change the setting for the milk system rinsing. T Adjust the water hardness. T Keep track of all products prepared and view the

number of maintenance programmes performed.

4 Permanent settings in programming mode

Adjusting the product settings

Product Coffee strength Amount Temperature

‘Ristretto’, ‘Espresso’ ‘Coffee’ 8 levels Coffee: 25ml–240ml normal, high ‘2 ristretti’, ‘2 espressi’, ‘2 coffees’ ‘Flat white’ 8 levels Coffee: 25ml–240ml

‘Cappuccino’, ‘Latte macchiato’

‘Milk foam’ – Milk: 3sec.–120sec. – ‘Hot water’ – Water: 25ml–450ml low, normal, high

8 levels Coffee: 15ml–80ml normal, high

8 levels Coffee: 25ml–240ml

In the programme item ‘Expert mode’ you can make individual settings for all speciality coffees and hot water. The following permanent settings can be made:

– Coffee: The amount set for

the single product is doubled.

Milk: 3sec.–120sec.

Milk: 3sec.–120sec. Interval: 0sec.–60sec.

Permanent settings in programming mode always follow the same model.

Example:Proceed as follows to change the coffee strength for one coffee.

T Press the T Press the T Press the

‘Expert mode’

‘Pc’ button.

‘>’ button several times until ‘3/6’ is displayed.

‘Expert mode’ button.

as for single product

normal, high

E Next select the button of the product for which you would like

to make settings. No product is prepared at this point.

E To display more products, press the

T Press the

‘Coffee’

T Press the ‘Coffee strength’ button.

‘Coffee’ and the coffee strength is displayed.

T Press the

fee strength.

‘Coffee’ button.

‘<’ or ‘>’ button to change the setting for the cof-

‘>’ button (bottom right).

4 Permanent settings in programming mode

T Press the ‘Save’ button.

‘Saved’ appears briefly on the display. ‘Coffee’

T Press the ‘’ button for around 2 seconds to exit program-

ming mode.

Enable or disable setting of cup volume

In the programme item make the following setting:

‘Ac tiv e’: The function ‘Permanently setting the amount of

water for the cup size’ is activated. You can adjust the amount of water to the cup size by pressing and holding the relevant preparation button.

‘Inactive’: The function ‘Permanently setting the amount of

water for the cup size’ is deactivated. The amount of water cannot be adjusted to the cup size by pressing and holding the relevant preparation button.

Example:Proceed as follows to disable the function ‘Permanently setting the amount of water for the cup size’.

T Press the T Press the T Press the

‘Customise cup fill volume’

T Press the ‘Inactive’ button. T Press the

‘Saved’ appears briefly on the display. ‘3/6’

T Press the ‘’ button to exit programming mode.

‘3/6’/ ‘Customise cup fill volume’ you can

‘Pc’ button.

‘>’ button several times until ‘3/6’ is displayed.

‘Customise cup fill volume’ button.

‘Save’ button.

Enable or disable one-off settings

In the programme item following setting:

‘Ac tiv e’: One-off settings can be made during preparation (e.g.

coffee strength or amount of water).

‘Inactive’: One-off settings cannot be made during prepara-

tion. The product is prepared according to the settings in programming mode (

‘3/6’/ ‘One-off settings’ you can make the

‘3/6’ / ‘Expert mode’).

4 Permanent settings in programming mode

Example:Proceed as follows to disable one-off settings during prep-

aration.

T Press the T Press the T Press the

‘One-off settings’

T Press the ‘Inactive’ button. T Press the

‘Saved’ appears briefly on the display. ‘3/6’

T Press the ‘’ button to exit programming mode.

‘Pc’ button.

‘>’ button several times until ‘3/6’ is displayed.

‘One-off settings’ button.

‘Save’ button.

Enable and disable products

Automatic switch-off

In the programme item ble each product individually.

Example:Proceed as follows to disable the preparation of hot water.

T Press the T Press the T Press the

‘Lock/enable’

E The lock symbol beside the product name indicates whether

the product is enabled or disabled. If the lock is closed, the product is disabled.

T Press the

played.

T Press the

The lock is closed. Hot water preparation is now disabled.

T Press the

ming mode.

By instructing your JURA to automatically switch itself off, you can cut down your energy consumption. If this function is activated, your JURA switches off automatically after the preset time following the last action on the machine.

‘3/6’/ ‘Lock/enable’ you can enable or disa-

‘Pc’ button.

‘>’ button several times until ‘3/6’ is displayed.

‘Lock/enable’ button.

‘>’ button until the product ‘Hot water’ is dis-

‘Hot water’ button.

‘’ button for around 2 seconds to exit program-

You can set the automatic switch-off to 15minutes, 30minutes or 1–9hours.

T Press the

‘Pc’ button.

4 Permanent settings in programming mode

T Press the ‘>’ button several times until ‘4/6’ is displayed. T Press the

‘Switch off after’

T Press the ‘<’ or ‘>’ button to change the switch-off time. T Press the

‘Saved’ appears briefly on the display. ‘4/6’

T Press the ‘’ button to exit programming mode.

‘Switch off after’ button.

‘Save’ button.

Milk system rinsing

Setting the water hardness

In the programme item the following settings:

‘Manual’: You are prompted to perform milk system rinsing

10minutes after preparation of a speciality coffee with milk.

‘Automatic’: The milk system rinsing is automatically initiated

10minutes after preparation of a speciality coffee with milk.

Example:Proceed as follows to set the milk system rinsing to be initiated automatically 10 minutes after the preparation.

T Press the T Press the T Press the

‘Rinse the milk system’

T Press the ‘Automatic’ button. T Press the

‘Saved’ appears briefly on the display. ‘4/6’

T Press the ‘’ button to exit programming mode.

The harder the water is, the more frequently the JURA needs to be descaled. It is therefore important to set the water hardness accurately.

The water hardness was set when the machine was first used. You can change this setting at any time.

‘4/6’ / ‘Rinse the milk system’ you can make

‘Pc’ button.

‘>’ button several times until ‘4/6’ is displayed.

‘Rinse the milk system’ button.

‘Save’ button.

The total water hardness can be adjusted on a continuous scale between 1°dH and 30°dH.

T Press the T Press the

‘Pc’ button.

‘>’ button several times until ‘5/6’ is displayed.

4 Permanent settings in programming mode

T Press the ‘Water hardness’ button.

‘Water hardness’

T Press the ‘< ’ or ‘>’ button to change the setting for the

water hardness.

T Press the

‘Saved’ appears briefly on the display. ‘5/6’

T Press the ‘’ button to exit programming mode.

‘Save’ button.

Unit for amount of water

Language

Example:Proceed as follows to change the unit for the amount of

water from

Example:Proceed as follows to change the language from to

‘Deutsch’.

‘ml’ to ‘oz’.

T Press the T Press the T Press the

‘Units’

T Press the ‘oz’ button. T Press the

‘Saved’ appears briefly on the display. ‘4/6’

T Press the ‘’ button to exit programming mode.

T Press the T Press the T Press the

‘Choose language’

E To display more languages, press the ‘ > ’ button (bottom

right).

T Press the button that corresponds to the language you want,

e.g.

‘Gespeichert’ appears briefly on the display. ‘4/6’

T Press the ‘’ button to exit programming mode.

‘Pc’ button.

‘>’ button several times until ‘4/6’ is displayed.

‘Units’ button.

‘Save’ button.

‘English’

‘Pc’ button.

‘>’ button several times until ‘4/6’ is displayed.

‘Choose language’ button.

‘Deutsch’.

4 Permanent settings in programming mode

Query counter readings and version

In the programme item ‘6/6’ you can view the following information.

‘Product counter’: Number of prepared speciality coffees and

hot water

‘Day counter’: Number of prepared speciality coffees and hot

water. This counter can be reset to zero.

‘Maintenance counter’: Number of maintenance programmes

performed (cleaning, descaling etc.)

‘Version’: Software version

Example:Proceed as follows to reset the day counter.

T Press the T Press the T Press the T Press the

‘Delete the day counter?’

T Press the ‘Yes’ button.

‘Saved’ appears briefly on the display. ‘6/6’

T Press the ‘’ button to exit programming mode.

‘Pc’ button.

‘>’ button several times until ‘6/6’ is displayed.

‘Day counter’ button.

‘’ button.

5 Maintenance

Your JURA has the following integrated maintenance programmes:

Rinsing the machine (‘Rinse the coffee system’)

Rinsing the fine foam frother (‘Rinse the milk system’)

Cleaning the fine foam frother (‘Clean the milk system’)

Changing the filter (‘Filter’)

Cleaning the machine (‘Clean’)

Descaling the machine (‘Descale’)

E Carry out each maintenance programme when you are

prompted to do so.

E Press the

grammes. When the bar is completely filled with red, your JURA will prompt you to perform the appropriate maintenance programme.

‘Pc’ button to view a list of the maintenance pro-

Rinsing the machine

Rinsing the milk system

You can start coffee system rinsing manually at any time.

T Place a receptacle under the coffee spout. T Press the T Press the T Press the

operation.

‘Machine is rinsing’, water flows out of the coffee spout. The

operation stops automatically.

After each milk preparation, the JURA prompts you to perform a milk system rinse.

E In programming mode, you can set whether the milk system

rinsing is to be prompted 10 minutes after preparation or initiated automatically (see Chapter 4 ‘Permanent settings in programming mode – Milk system rinsing’).

Precondition:

‘Pc’ button.

‘>’ button.

‘Rinse the coffee system’ button to start the rinse

‘Rinse the milk system’ is displayed.

5 Maintenance

T Place a receptacle under the fine foam frother. T Press the

‘Pc’ button. ‘Milk system is being rinsed’, the fine foam frother is rinsed.

The operation stops automatically.

Cleaning the milk system

CAUTION

To ensure that the fine foam frother always works properly, you must clean it daily when you have been preparing milk.

If the wrong cleaning agent is used, the machine could be damaged and/or traces could be left behind in the water.

T Use only original JURA maintenance products.

E JURA milk system cleaner is available from specialised dealers. E To clean the milk system, use the container supplied.

T Press the T Press the

‘Pc’ button.

‘Clean the milk system’ button. ‘Clean the milk system’

T Press the ‘Start’ button. T Press the

‘Next’ button. ‘Clean the milk system’ / ‘Milk system cleaner’

T Remove the milk pipe from the milk container or carton. T Add milk system cleaner to the front part of the container

up to the bottom mark (indicated by 6).

T Then fill with water up to the upper mark. T Place the container under the fine foam frother.

T Connect the milk pipe to the container.

E To connect the milk pipe to the container correctly, the pipe

must be fitted with a connector.

5 Maintenance

T Press the ‘Next’ button.

‘Milk system is being cleaned’ appears and the fine foam

frother and the milk pipe are cleaned.

‘Clean the milk system’ / ‘Fresh water’

T Rinse the container thoroughly and fill the front part with

fresh water up to the upper mark.

T Place this under the fine foam frother and reconnect the

milk pipe to the container.

T Press the

‘Next’ button. ‘Milk system is being cleaned’, the fine foam frother and the

milk pipe are rinsed with fresh water. The operation stops automatically.

Dismantling and rinsing the fine foam frother

Dismantling and rinsing the professional fine foam frother

To make sure the fine foam frother works properly, and in the interests of hygiene, it must be dismantled and rinsed daily if you have been preparing milk. Your JURA will not prompt you to dismantle and rinse the frother.

T Remove the milk pipe and rinse it thoroughly under running

water.

T Carefully remove the fine foam frother from the Connector

System

by twisting slightly.

T Dismantle the fine foam frother into its individual parts. T Rinse all the parts under running water. If there are severely

dried-on milk residues, firstly immerse the individual parts in a solution of 250ml cold water and 1 capful of JURA milk system cleaner. Then rinse the parts thoroughly.

T Re-assemble the fine foam frother.

E Ensure that all individual parts are correctly and firmly con-

nected to ensure optimum operation.

T Firmly attach the fine foam frother to the Connector Sys-

tem

To make sure the professional fine foam frother works properly, and in the interests of hygiene, it must be dismantled and rinsed daily if you have been preparing milk. Your JURA will not prompt you to dismantle and rinse the professional fine foam frother.

T Remove the milk pipe and rinse it thoroughly under running

water.

5 Maintenance

T Carefully remove the professional fine foam frother from the

Connector System

by twisting slightly.

T Dismantle the professional fine foam frother into its individ-

ual parts.

T Rinse all the parts under running water. If there are severely

dried-on milk residues, firstly immerse the individual parts in a solution of 250ml cold water and 1 capful of JURA milk system cleaner. Then rinse the parts thoroughly.

T Re-assemble the professional fine foam frother.

E Ensure that all individual parts are correctly and firmly con-

nected to ensure optimum operation of the professional fine foam frother.

T Firmly attach the professional fine foam frother to the Con-

nector System

Inserting the filter

Your JURA no longer has to be descaled if you are using the CLARIS Pro Smart filter cartridge. If you did not insert the filter cartridge the first time you used the machine, you can do this now as follows.

T Remove and empty the water tank. T Open the filter holder. T Insert the filter cartridge into the water tank. T Close the filter holder. It will click into place audibly. T Fill the water tank with fresh, cold water and reinsert the

tank.

E The machine automatically detects that you have just inserted

the filter cartridge.

‘Saved’ appears briefly on the display. ‘Filter is beingrinsed’, the water flows directly into the drip

tray. Rinsing of the filter stops automatically.

E If the filter is active, this is indicated by a blue filter symbol at

the bottom of the display.

5 Maintenance

Changing the filter

Cleaning the machine

E Once the filter cartridge stops working (depending on the

water hardness setting), the JURA will prompt you to change the filter.

E CLARIS Pro Smart filter cartridges are available from special-

ised dealers.

Precondition:The filter symbol at the bottom of the display lights up red.

T Remove and empty the water tank. T Open the filter holder and remove the old CLARIS Pro Smart

filter cartridge.

T Insert the filter cartridge into the water tank. T Close the filter holder. It will click into place audibly. T Fill the water tank with fresh, cold water and reinsert the

tank.

‘Saved’ appears briefly on the display. The machine has

automatically detected that you have just changed the filter cartridge.

‘Filter is beingrinsed’, the water flows directly into the drip

tray. Rinsing of the filter stops automatically.

After 180preparations or 80switch-on rinses, the JURA will prompt you to clean it.

CAUTION

If the wrong cleaning agent is used, the machine could be damaged and/or traces could be left behind in the water.

T Use only original JURA maintenance products.

E The cleaning programme lasts approximately 20 minutes. E Do not interrupt the cleaning programme. The quality of

cleaning will be impaired if you do so.

E JURA cleaning tablets are available from specialised dealers.

Precondition:

T Press the T Press the T Press the

‘Clean machine’ is displayed.

‘Pc’ button (red Maintenance symbol).

‘Start’ button.

‘Next’ button. ‘Empty coffee grounds container’

5 Maintenance

T Empty the drip tray and coffee grounds container and put

them back into the machine.

‘Clean’

T Place one receptacle under the coffee spout and another

under the fine foam frother.

T Press the

‘Next’ button. ‘Machine is being cleaned’, water flows out of the coffee

spout. The operation is interrupted,

‘Add cleaning tablet’.

T Open the cover of the filler funnel for ground coffee. T Insert a JURA cleaning tablet into the filler funnel. T Close the cover of the filler funnel. T Press the

‘Next’ button. ‘Machine is being cleaned’, water flows repeatedly out of the

coffee spout and the fine foam frother. The operation stops automatically.

‘Empty coffee grounds container’

T Empty the drip tray and coffee grounds container and put

them back into the machine. Cleaning is now complete.

Descaling the machine

CAUTION

The JURA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the hardness of your water.

E If you are using a CLARIS Pro Smart filter cartridge, you will not

be prompted to descale.

If the descaling agent comes into contact with the skin or eyes, this can cause irritation.

T Avoid contact with the skin or eyes. T Rinse off the descaling agent with clean water. Should you get

any descaling agent in your eye, see a doctor.

If the wrong descaling agent is used, the machine could be damaged and/or traces could be left behind in the water.

T Use only original JURA maintenance products.

5 Maintenance

CAUTION

If the descaling operation is interrupted, there may be damage to the machine.

T Allow the descaling programme to run to the end.

If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out.

T Clean up any splashes immediately.

E The descaling programme lasts approximately 40minutes. E JURA descaling tablets are available from specialised dealers.

Precondition:

T Press the T Press the T Press the

‘Decalcify machine’ is displayed.

‘Pc’ button (red Maintenance symbol).

‘Start’ button.

‘Next’ button. ‘Empty drip tray’

T Empty the drip tray and coffee grounds container and put

them back into the machine.

‘Agent in tank’

T Remove and empty the water tank. T Completely dissolve 3JURA descaling tablets in a receptacle

holding 500ml of water. This may take several minutes.

T Pour the solution into the empty water tank and insert it into

the machine.

T Place a receptacle under the fine foam frother. T Press the

‘Next’ button. ‘Machine is being descaled’, appears and water flows out of

the fine foam frother repeatedly. The operation is interrupted,

‘Empty drip tray’.

T Empty the drip tray and coffee grounds container and put

them back into the machine.

‘Fill water tank’

T Remove the water tank and rinse it thoroughly. T Fill the water tank with fresh, cold water and reinsert the

tank.

5 Maintenance

T Place one receptacle under the coffee spout and another

under the fine foam frother.

T Press the

‘Machine is being descaled’, the descaling operation is

continued. The operation is interrupted,

T Empty the drip tray and coffee grounds container and put

them back into the machine. Descaling is now complete.

E If the descaling operation stops unexpectedly, rinse the water

tank thoroughly.

‘Next’ button.

‘Empty drip tray’.

Cleaning the bean container

Descaling the water tank

Coffee beans may be covered with a slight oil film which remains on the walls of the bean container. These traces may negatively affect the coffee result. For this reason clean the bean container from time to time.

Precondition:

T Switch the machine off with the On/Off button Q. T Remove the aroma preservation cover. T Clean the bean container with a soft, dry cloth. T Fill the bean container with coffee beans and close the

Limescale deposits may form in the water tank. To ensure correct function of the machine, descale the water tank from time to time.

T Remove the water tank. T If you use a CLARIS Pro Smart filter cartridge, remove this. T Completely fill the water tank and dissolve 3 JURA descaling

T Leave the water tank with the descaling solution for several

T Empty the water tank and rinse it thoroughly. T If you use a CLARIS Pro Smart filter cartridge, insert this

T Fill the water tank with fresh, cold water and reinsert the

‘Fill bean container’ is displayed.

aroma preservation cover.

tablets in it.

hours (e.g. overnight).

again.

tank.

6 Display messages

Message Cause/Result Action

‘Fill water tank’ The water tank is empty.

You cannot prepare any products.

‘Empty coffee grounds container’

‘Drip tray not fitted’

‘Fill bean container’

‘Rinse the milk system’

The filter symbol at the bottom of the display lights up red.

‘Clean machine’ The JURA is prompting you to

‘Decalcify machine’

‘Too hot’ The system is too hot to start a

The coffee grounds container is full. You cannot prepare any products.

The drip tray is not inserted correctly or is not inserted at all. You cannot prepare any products. The bean container is empty. You cannot prepare any speciality coffees, but you can prepare hot water and milk. The JURA requests a milk system rinse.

The filter cartridge no longer works.

clean it.

The JURA is prompting you to descale it.

maintenance programme.

T Fill the water tank (see Chapter 3 ‘Daily operation – Filling the water tank’).

T Empty the coffee grounds container and the drip tray (see Chapter 3 ‘Daily operation – Daily maintenance’).

T Fit the drip tray.

T Fill the bean container (see Chapter 1

‘Preparing and using for the first time – Filling the bean container’).

T Perform milk system rinsing (see Chapter 5 ‘Maintenance – Rinsing the milk system’).

T Replace the CLARIS Pro Smart filter cartridge (see Chapter 5 ‘Maintenance – Changing the filter’).

T Perform cleaning (see Chapter 5 ‘Maintenance – Cleaning the machine’).

T Perform descaling (see Chapter 5 ‘Maintenance – Descaling the machine’).

T Wait for several minutes until the system has cooled or prepare a speciality coffee or hot water.

7 Troubleshooting

Problem Cause/Result Action

Insufficient foam is produced when the milk is frothed or milk sprays out of the fine foam frother.

Coffee only comes out in drips when it is being prepared.

‘Fill water tank’ is

displayed although the water tank is full.

Little or no water or steam comes out of the fine foam frother. The pump is very quiet.

Grinder is making a very loud noise.

‘ERROR2’ or ‘ERROR5’ is

displayed.

The fine foam frother is dirty.

The coffee is ground too finely and obstructs the system.

The water tank float is trapped.

The connector of the fine foam frother may be blocked by milk residues or limescale fragments loosened during descaling.

There are foreign objects in the grinder.

If the machine has been exposed to the cold for a long period of time, heating may be disabled for safety reasons.

T Clean the fine foam frother (see Chapter 5 ‘Maintenance – Cleaning the milk system’). T Dismantle and rinse the fine foam frother (see Chapter 5 ‘Maintenance – Dismantling and rinsing the fine foam frother’).

T Set the grinder to a coarser setting (see Chapter 2 ‘Preparation – Adjusting the grinder’).

T Descale the water tank (see Chapter 5 ‘Maintenance – Descaling the water tank’).

T Remove the fine foam frother. T Unscrew the black connector with the

aid of the hexagonal hole on the measuring spoon for ground coffee.

T Clean the connector thoroughly. T Screw the connector back on by hand. T Carefully tighten it using the hexagonal

hole on the measuring spoon, turning by no more than a quarter of a rotation.

T Contact customer support in your country (see Chapter 11 ‘JURA contact details/ Legal information’).

T Warm the machine at room temperature.

7 Troubleshooting

Problem Cause/Result Action

‘ERROR’ messages

Other are displayed.

–

T Switch the JURA off with the On/Off button Q. Contact customer support in your country (see Chapter 11 ‘JURA contact details/ Legal information’).

E If you were unable to solve the problem, contact customer

support in your country (see Chapter 11 ‘JURA contact details/ Legal information’).

8 Transport and environmentally friendly disposal

Transport/ Emptying the system

Disposal

Keep the packaging for your JURA. It should be used to protect the machine during transport.

In order to protect the JURA from frost during transport, the system must be emptied.

T Remove the milk pipe from the fine foam frother. T Place a receptacle under the fine foam frother. T Press the

‘Milk foam’ appears and hot steam is discharged from the

fine foam frother.

T Remove and empty the water tank. T Press the

‘60sec.’ is displayed.

Steam will continue to be discharged from the fine foam frother until the system is empty.

‘Fill water tank’

T Press the On/Off button Q.

Your JURA is switched off.

Please dispose of old machines in an environmentally neutral way.

Old machines contain valuable, recyclable materials which should be recycled. Please therefore dispose of old machines via suitable collection systems.

‘Milk foam’ button.

‘>’ button several times until ‘Amount of milk’ /

9 Technical data

Voltage 220–240V~, 50Hz Power 1450W Ambient conditions Humidity max. 80 %

Ambient temperature 10–35°C

Conformity mark

Pump pressure static, max. 15bar Holding capacity of water tank (without filter) Holding capacity of bean container 500g Holding capacity of coffee grounds container Cable length approx. 1.1m Weight approx. 10.0kg Dimensions (WHD) 29.5  41.75  44.36cm

Information for testers (repeat test in accordance with DIN VDE 0701-0702): The central grounding point (CGP) is located on the underside of the machine, right next to the mains cable's connection point.

3l

max. 25portions

10 Index

Addresses 48 Adjusting the product settings 24 Aroma preservation cover

Bean container with aroma preservation cover 4

Automatic switch-off 26

Bean container

Bean container with aroma preservation cover 4 Cleaning 37 Filling 10

Bus bar

Technical data 42

Button

On/Off button 4

Cappuccino 15 Cappuccino frother cleaning

Cleaning the milk system 31

Cappuccino frother rinsing

Rinsing the milk system 30 Central grounding point 42 CLARIS Pro Smart filter cartridge

Change 34

Insert 33 Cleaning

Bean container 37

Machine 34 Coffee 16

Two coffees 16 Coffee grounds container 4 Coffee spout

Height-adjustable coffee spout 4 Consistency of grind

Adjusting the grinder 19

Grinder adjustment switch 4 Contact details 48 Cover

Filler funnel for ground coffee 4

Water tank 4 Cup grille 4 Customer support 48

Daily maintenance 21 Day counter 29 Descaling

Machine 35 Water tank 37

Disable

Products 26 Display 5 Display messages 38 Disposal 41 Double product 16 Drip tray 4

Emptying the system 41 Enable

Products 26 Errors

Troubleshooting 39 Espresso 16

Two espressi 16

Filler funnel

Filler funnel for ground coffee 4 Filling

Bean container 10

Water tank 20 Filter

Change 34

Insert 33 Fine foam frother 4

Cleaning 31

Dismantling and rinsing 32

Professional fine foam frother 5

Rinsing 30 First-time use 11

With filter cartridge activation 12

Without filter cartridge activation 13 Flat white 15

Grinder adjustment switch 4 Ground coffee 17

Measuring spoon for ground coffee 5 Grounding point 42

10 Index

Height-adjustable coffee spout 4 Homepage 10 Hotline 48 Hot water 19 Hot-water nozzle 5

Instant coffee

Ground coffee 17

Internet 10

JURA

Contact details 48 Internet 10

Language 28 Latte macchiato 15

Machine

Cleaning 34 Daily maintenance 21 Descaling 35 Regular maintenance 21 Rinsing 30 Setting up 10 Switching off 22

Switching on 20 Mains cable 4 Maintenance 30

Daily maintenance 21

Regular maintenance 21 Maintenance counter 29 Measuring spoon for ground coffee 5 Messages, display 38 Milk

Connecting milk 14 Milk foam 17 Milk system

Cleaning 31

Rinsing 30 Milk system rinsing 27

Number

Maintenance programmes 29

Preparations 29

Permanently setting the water for the cup

size 18

Permanent settings in programming mode

Preparation 15

Cappuccino 15 Coffee 16 Espresso 16 Flat white 15 Ground coffee 17 Hot water 19 Latte macchiato 15 Milk foam 17 Ristretto 16 Two coffees 16 Two espressi 16 Two ristretti 16 Two speciality coffees 16

Problems

Troubleshooting 39 Product counter 29 Products

Disable 26

Enable 26 Product settings

Adjusting 24 Professional fine foam frother 5

Dismantling and rinsing 32 Programming mode 23

Automatic switch-off 26

Counter readings and version 29

Enable or disable setting of cup volume

Language 28

Milk system rinsing 27

One-off settings 25

Setting the water hardness 27

Unit for amount of water 28 Proper use 6

Regular maintenance 21 Rinsing

Machine 30 Ristretto 16

Two ristretti 16

Safety 6 Safety information 6 Settings

Permanent settings in programming mode 23

Setting up

Setting up the machine 10 Short operating instructions 10 Switching off 22 Switching on 20 Switch-off

Automatic switch-off 26 Symbol description 3

Technical data 42 Tel 48 Transport 41 Troubleshooting 39 Two products 16

Unit for amount of water 28 Use, First-time 11

Version 29

Water hardness

Determining the water hardness 10

Setting the water hardness 27 Water tank 4

Descaling 37

Filling 20 Website 10

10 Index

464748

J72636/WE8/en/201702

11 JURA contact details/ Legal information

Your JURA service partner

JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Tel. +41 (0)62 38 98 233 www.jura.com

Directives

Technical changes

Feedback

The machine complies with the following directives:

2006/42/EC– Machinery Directive

2014/30/EU– Electromagnetic Compatibility

2009/125/EC– Ecodesign Directive

2011/65/EU– RoHS Directive

We reserve the right to make technical changes. The diagrams used in these instructions for use are for illustration purposes only and do not represent the original colours of the machine. Some details of your JURA may vary.

Your opinion is important to us! Use the contact details at www.jura.com.

The instructions for use contain information which is protected by copyright. It is not permitted to photocopy these instructions for use or translate them into another language without the prior written consent of JURA Elektroapparate AG.

JURA WE8 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual