Jura IMPRESSA J7 User Manual

Page 1

The IMPRESSA J7 Manual

The ‘IMPRESSA Manual’ has been awarded the seal of approval by the independent German Technical Inspection Agency, TÜV SÜD, due to its easy-to-understand style, its thoroughness and coverage of safety aspects.

Page 2

Table of contents

Your IMPRESSA J7

IMPORTANT SAFEGUARDS 4 Control elements Proper Use For your safety The IMPRESSA J7 Manual

Symbol description ......................................................................................................................................13

1 IMPRESSA J7 14

Connector System© ....................................................................................................................................15

JURA on the internet ....................................................................................................................................15

Knowledge Builder .......................................................................................................................................15

2 Preparing and using for the first time 16

Supplied as standard ...................................................................................................................................16

Setting up ......................................................................................................................................................16

Filling the water tank ...................................................................................................................................16

Filling the bean container ...........................................................................................................................17

First-time use ................................................................................................................................................17

Inserting and activating the filter ..............................................................................................................18

Determining and adjusting the water hardness .....................................................................................19

Adjusting the grinder .................................................................................................................................20

Switching on .................................................................................................................................................21

Switching off ................................................................................................................................................ 22

3 Familiarising yourself with the control options 23

Preparation at the touch of a button .......................................................................................................23

One-off settings before and during preparation ...................................................................................24

Setting the water for the cup size ............................................................................................................26

Permanent settings in programming mode ..........................................................................................26

4 Preparation at the touch of a button 29

Ristretto, espresso and coffee ...................................................................................................................29

Cappuccino...................................................................................................................................................30

Pre-ground Coffee .......................................................................................................................................31

Foaming and heating milk with the Professional Cappuccino Frother ............................................. 32

Foaming milk with the Easy Cappuccino Frother ................................................................................. 33

Hot water ......................................................................................................................................................34

Page 3

Table of contents

5 Permanent settings in programming mode 35

Products ........................................................................................................................................................35

Energy Save Mode ......................................................................................................................................36

Automatic switch-off .................................................................................................................................. 37

Rinsing...........................................................................................................................................................38

Restore factory settings ............................................................................................................................. 38

Viewing information and maintenance status ......................................................................................39

Unit, amount of water ................................................................................................................................40

Language .......................................................................................................................................................41

6 Maintenance 42

Maintenance tips .........................................................................................................................................42

Rinsing the machine ...................................................................................................................................42

Changing the filter ......................................................................................................................................43

Cleaning the machine ................................................................................................................................45

Descaling the machine ...............................................................................................................................46

Rinsing the cappuccino frother ................................................................................................................48

Cleaning the cappuccino frother ..............................................................................................................49

Dismantling and rinsing the Professional Cappuccino Frother ...........................................................51

Dismantling and rinsing the Easy Cappuccino Frother .........................................................................51

Cleaning the bean container ......................................................................................................................51

Descaling the water tank ...........................................................................................................................52

7 Display messages 53 8 Troubleshooting 9 Transport and environmentally neutral disposal

Transport / Emptying the system .............................................................................................................57

Disposal .........................................................................................................................................................57

10 Technical data 58 Index

JURA contact details / Legal information

Page 4

Important Safeguards

IMPORTANT SAFEGUARDS

These safeguards apply for machines with UL safety test (see rating plate and chapter 10, ‘Technical data’).

Follow the basic safety

Follow the basic safety precautions

precautions

When using electrical appliances, basic safety precautions should always be followed, to reduce the risk of fire, electric shock, and/or injury to persons, including the following:

Read all instructions.

Do not touch hot surfaces. Use handles or knobs.

To protect against fire, electric shock and injury to persons, do

not immerse cord, plugs, or body of machine in water or other liquid.

Close supervision is necessary when any appliance is used by or near children.

Unplug from outlet when not in use and before cleaning. Allow to cool before putting or taking off parts, and before cleaning the appliance.

Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.

The use of accessory attachement not recommended by the appliance manufacturer may result in fire, electric shock, or injury to persons.

Do not use outdoors.

Do not let the cord hang over the edge of a table or counter, or touch hot surfaces.

Do not place on or near a hot gas or electric burner, or in a heated oven.

Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control to ‘OFF’ then remove plug from wall outlet.

Do not use appliance for other than intented use.

Use extreme caution when dispensing hot steam.

For household use only.

SAVE THESE INSTRUCTIONS

Page 5

Important Safeguards

Special cord set instructionsSpecial cord set instructions

a. A short power supply cord is provided to reduce the risk

resulting from becoming entangled in or tripping over a long

cord. Your IMPRESSA has a 3-pin grounded plug. b. Longer extension cords are available and may be used if care

is exercised in their use. c. If an extension cord is used,

1. the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance, and

2. if the appliance is of the grounded type, the extension cord should be a grounding type 3-wire cord, and

3. the longer cord shall be arranged so that it will not drape over the counter top or tabletop where it can be pulled on by children of tripped over.

As a safety feature, this plug will fit in a polarized outlet only

one way. If the plug does not fit fully in the outlet, reverse the plug. If it

still does not fit, contact a qualified electrician. Do not modify the plug in any way or attempt to defeat this

safety feature.

WarningWarning

CautionCaution

To reduce the risk of fire or electric shock, do not remove any service covers. No user serviceable parts inside. Repair should be done by authorized personnel only.

This appliance is for household use. Any servicing other than cleaning and user maintenance should be performed by an authorized service representative:

Do not immerse base in water or try to disassemble.

To reduce the risk of fire or electric shock, do not remove the

base. No user serviceable parts inside. Repair should be done by authorized service personnel only. Check voltage to be sure that the voltage indicated on the

name plate agreees with your voltage. Never use warm or hot water to fill the water container! Use

cold water only.

Page 6

Important Safeguards

NEVER DO

NEVER DO (or you will void your

(or you will void your warranty protection):

warranty protection):

Keep your hands and the cord away from hot parts of the

appliance during operation. Never clean with scouring powders or hard implements.

Never fill instant coffee, chocolate mix etc. into the grinder or

ground coffee funnel (grinder by-pass). It will damage the functioning of the brewing chamber. Never fill sugar coated coffee beans into the bean hopper. In

case of doubt, call your dealer. Never fill anything other than coffee beans into the bean con-

tainer (no chocolate, no rice, no nuts, no spices, nothing other than roasted coffee beans). Never do anything with the machine which is not described in

the User‘s Manual. In case of doubt, call your dealer.

Page 7

Important Safeguards

Page 8

Control elements

1 2 3

Figure: IMPRESSA J7 Piano Black

1 Bean container cover 2 Water tank cover 3 Bean container with aroma preservation

cover 4 Water tank 5 Height- and width-adjustable coffee spout 6 Coffee grounds container 7 Drip tray

8 Filler funnel for pre-ground coffee 9 Grinder adjustment switch 10 Storage compartment cover 11 Storage compartment with measuring

spoon for pre-ground coffee and hot water nozzle

12 Connector System

for removable

frothers and nozzles 13 Professional Cappuccino Frother 14 Power switch and mains cable

(side of machine) 15 Cup platform

12 13

Page 9

Control elements

31 2

Surface of the machine:

1 Q On/off button 2 Rotary Switch 3 c Maintenance button

The Connector System

permits the use of different frothers and nozzles. These are available from

stockists.

Front: 4 Display

. Start symbol u Ristretto symbol i Espresso symbol o Coffee symbol

; Mild : Normal _ Strong m Hot water symbol n Steam symbol

5 Easy Cappuccino Frother 6 Professional Cappuccino Frother 7 Hot water nozzle

Page 10

Important information

Proper UseProper Use

The machine is designed and intended for private domestic use. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use.

Before using the machine always read this manual thoroughly and completely and comply with the instructions it contains. Keep this IMPRESSA Manual close to the machine and pass it on to the next user if applicable.

For your safety

Please carefully read and observe the important safety information set out below. To avoid danger of potentially fatal electric shock:

Never use a machine which is damaged or has a defective

mains cable. In the event of signs of damage, for example if there is a smell

of burning, unplug the machine immediately from the mains supply and contact JURA service. If the mains cable of this machine is damaged, it must be

repaired either directly by JURA or by an authorised JURA service centre. Make sure that the IMPRESSA and the mains cable are not

located close to hot surfaces. Be careful to ensure that the mains cable does not get caught

and does not rub against sharp edges. Never open and repair the machine yourself. Do not modify

the machine in any way that is not described in the IMPRESSA Manual. The machine contains live parts. If opened, there is a danger of potentially fatal injury. Repairs may only be carried out by authorised JURA service centres, using original spare parts and accessories.

Page 11

Important information

There is a risk of scalds or burns on the spouts or the frother:

Place the machine out of the reach of children.

Do not touch any hot parts. Use the handles provided.

Be careful to ensure that the appropriate frother is correctly

installed and clean. The frother or parts of the frother might come off if the parts are not assembled correctly or a blockage occurs.

A defective machine is not safe and could cause injury or fire. To avoid damage and any associated risk of injury or fire:

Never allow the mains cable to loosely hang down. The mains

cable could pose a tripping hazard or become damaged. Protect your IMPRESSA from environmental influences such

as rain, frost and direct sunlight. Do not immerse the IMPRESSA, cable or connections in

water. Do not put the IMPRESSA or any individual parts in the dish-

washer. Turn your IMPRESSA off at the power switch before any clean-

ing operation. Always wipe your IMPRESSA with a damp cloth rather than a wet one, and protect it from prolonged exposure to water splashes. Only connect the machine to a mains voltage in accordance

with the information on the rating plate. The rating plate is located on the underside of your IMPRESSA. Further technical data is given in Chapter 10 ‘Technical Data’. Please only use original JURA maintenance products. Use of

products that are not explicitly recommended by JURA could damage the IMPRESSA. Do not use any coffee beans treated with additives or caramel-

ised coffee beans. Only fill the water tank with cold, fresh water.

Switch the machine off at the power switch if you are going to

be absent for a longer period of time.

Page 12

Important information

People, including children, who

do not have the physical, sensory or mental capabilities to use

the machine safely or are inexperienced or lack knowledge in how to use the machine

safely must be supervised by a responsible person when using it, or must be instructed in how to use it correctly.

Safety when handling the CLARIS Blue filter cartridge:

Filter cartridges should be kept out of the reach of children.

Store filter cartridges in a dry place in the sealed packaging.

Protect cartridges from heat and direct sunlight.

Do not use damaged cartridges.

Do not open filter cartridges.

Page 13

The IMPRESSA J7 ManualThe IMPRESSA J7 Manual

Symbol descriptionSymbol description

WarningsWarnings

The IMPRESSA J7 Manual

You are holding the manual for your IMPRESSA J7 in your hand. It will help you to familiarise yourself with your IMPRESSA safely and quickly and teach you the full range of facilities it offers:

Chapter 2, ‘Preparing and using for the first time’, explains

step-by-step how to set up and prepare the machine.

Chapter 3, ‘Familiarising yourself with the control options’ is

important for you to read as you are familiarising yourself

with your IMPRESSA.

All the other chapters are intended to help you when you have

a specific query.

You can download the short operating instructions for your

machine from the JURA website (www.jura.com).

CAUTION

Symbols usedSymbols used

E Information and tips to make it even easier to use your IMPRESSA.

T Prompt to take action. This symbol means that you are being prompted to

READY

Always take note of any information marked with the words CAUTION or WARNING and a warning sign. The signal word WARNING draws your attention to potential serious injury, and the signal word CAUTION to potential minor injury.

CAUTION draws your attention to potential damage to the machine.

References to the JURA website, which provides further information that may be of interest to you: www.jura.com

perform some action.

Display message

Page 14

1 IMPRESSA J7

1 IMPRESSA J71 IMPRESSA J7

Perfect Enjoyment,

Perfect Enjoyment, Perfect Aesthetics

Perfect Aesthetics

The uncompromising all-round design of the IMPRESSA J7 indulges the eyes as well as the taste buds. Gourmets will find plenty to delight them as their coffee dreams come true and they experience a new dimension of enjoyment with ristretto, espresso, coffee crème, cappuccino, latte macchiato and many other trendy specialities. This is easy to achieve, because the innovative operating concept leaves nothing to be desired when it comes to simplicity. And the integrated cup illumination places every speciality coffee in the right light.

Breathtakingly beautiful: Clear, no-frill contours and high-

quality materials set the tone of the design of the IMPRESSA

J series. All details have been exactly thought out and come

together to form an aesthetic whole that impresses in every

way. This makes the IMPRESSA J7 a true design feature in the

home, which, thanks to its compact design, can easily be

placed anywhere.

Pure ergonomics: The centrally arranged control elements,

with the unique Rotary Switch and a plain text display which

speaks your language, will allow you to quickly and intuitively

make your coffee wishes come true. The focus is fully on your

personal taste. Simply select the coffee strength, amount of

water and temperature according to your individual prefer-

ences. You can even choose between three hot water temper-

ature levels. Accessories such as the measuring spoon and the

hot water nozzle can be conveniently stored in the storage

compartment where they are always within reach.

Energy-saving made easy: The IMPRESSA J7 actively assists

you in saving energy.

With the Energy Save Mode (E.S.M.

energy saving potential to suit the way you like to enjoy your beverages.

) you can adjust the

Page 15

1 IMPRESSA J7

Zero-Energy Switch: When the IMPRESSA is switched off

with the on/off button, the machine is completely disconnected from the power supply.

Height- and width-adjustable coffee spout: The height- and

width-adjustable coffee spout is another JURA innovation. It

allows precise adaptation to cups of different heights and

diameters. This prevents the coffee from splashing and pro-

duces a delicious crema with the ideal consistency.

Connector System© Connector System©

JURA on the internet JURA on the internet

Knowledge Builder Knowledge Builder

The Connector System frothers:

Professional Cappuccino Frother

Cappuccino, latte macchiato

Hot milk and milk foam

Easy Cappuccino Frother

Cappuccino

Milk foam

Visit us on the internet.

At www.jura.com you will find interesting and up-to-date

information on your IMPRESSA and on every aspect of

coffee.

You can familiarise yourself with your IMPRESSA in a fun way on the PC.

The Knowledge Builder awaits you at www.jura.com. The

interactive assistant, LEO, will assist you and explain the ben-

efits of and how to use your IMPRESSA.

permits the use of different cappuccino

Page 16

2 Preparing and using for the first time

2 Preparing and using for the first time2 Preparing and using for the first time

This chapter provides you with the information you need to use your IMPRESSA without any problems. You will prepare your IMPRESSA step-by-step to enjoy your first perfect cup of coffee.

Supplied as standard Supplied as standard

Setting up Setting up

Filling the water tank Filling the water tank

The following items are supplied as standard:

Your JURA IMPRESSA J7 automatic coffee machine

The Welcome Pack, which includes:

The IMPRESSA J7 Manual

JURA cleaning tablets

Measuring spoon

Hot water nozzle

Aquadur®test strip

CLARIS Blue extension

CLARIS Blue filter cartridge

JURA Cappuccino Cleaner

Keep the packaging for your IMPRESSA. It should be used to protect the machine during transport.

When setting up your IMPRESSA, please note the following:

Set the IMPRESSA down on a horizontal surface that is not

sensitive to water.

Choose a spot for your IMPRESSA which is protected against

overheating.

To enjoy the perfect cup of coffee we recommend changing the water every day.

CAUTIONCAUTION

Milk, mineral water or other liquids can damage the water tank or the machine.

Only fill the water tank with fresh, cold water.

Open the water tank cover.

Remove the water tank and rinse it with cold water.

Fill the water tank with fresh, cold water and reinsert the

tank. Close the water tank cover.

Page 17

Filling the bean

Filling the bean container

container

2 Preparing and using for the first time

The bean container has an aroma preservation cover. This will ensure that your coffee beans retain their aroma for longer.

CAUTIONCAUTION

First-time use First-time use

WARNINGWARNING

Coffee beans which have been treated with additives (e.g. sugar), pre-ground coffee or freeze-dried coffee will damage the grinder.

Only use untreated coffee beans to refill the bean container.

Open the bean container cover and remove the aroma pres-

ervation cover. Remove any dirt or foreign objects inside the bean con-

tainer. Fill the bean container with coffee beans, then close the

aroma preservation cover and the bean container cover.

If the machine is operated with a defective mains cable, there is a danger of potentially fatal electric shock.

Never use a machine which has a defective mains cable.

Precondition: The water tank and bean container are full.

Insert the mains plug into a power socket.

T 3 T Switch on the IMPRESSA using the power switch on the

right-hand side of the machine.

Q T Press the on/off button to switch the IMPRESSA on.

The Rotary Switch lights up. appears on the display.

f T Turn the Rotary Switch until the required language is dis-

played, for example

k T Press the Rotary Switch to confirm the language.

LANGUAGE ENGLISH.

SPRACHE DEUTSCH

OK appears briefly on the display to confirm the setting. PRESS RINSE, the maintenance button c lights up.

Place a receptacle under the frother.

T c T Press the maintenance button.

SYSTEM FILLING, the system fills up with water.

A small amount of water flows from the frother. This operation stops automatically, the following appears on the display:

HEATING.

PRESS RINSE, the maintenance button c lights up.

Page 18

2 Preparing and using for the first time

Inserting and

Inserting and activating the filter

activating the filter

Place a receptacle under the coffee spout.

c T Press the maintenance button.

RINSING, the machine rinses. The operation stops auto-

matically.

READY appears on the display. Your IMPRESSA is ready for

use.

Your IMPRESSA no longer has to be descaled if you are using CLARIS Blue filter cartridges.

You can also try out the ‘Inserting the filter’ operation online.

Visit the Knowledge Builder at www.jura.com.

Perform the ‘Inserting the filter’ operation without interrup-

tions. This will ensure that your IMPRESSA always produces its

best.

Precondition:

k T Keep the Rotary Switch pressed until

g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

RINSE appears on

the display.

FILTER - is displayed.

NO -

g T Turn the Rotary Switch until YES w is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display to confirm the setting. INSERT, the maintenance button c lights up.

Remove the filter cartridge extension from the Welcome Pack.

Fit the extension on top of an original CLARIS Blue filter cartridge.

Remove and empty the water tank.

Lift the cartridge holder and insert the filter cartridge into the water tank, exerting slight pressure.

Close the cartridge holder. It will click into place audibly.

After two months, the filter will cease to work. You can check

the elapsed time by referring to the date plate on the cartridge

holder in the water tank.

Page 19

Determining and

Determining and adjusting the

adjusting the water hardness

water hardness

2 Preparing and using for the first time

Fill the water tank with fresh, cold water and reinsert the tank.

Place a receptacle (at least 500 ml) under the frother.

If you are using the Professional Cappuccino Frother, set the

selector switch of the frother to the steam position n.

c T Press the maintenance button.

FILTER RINSING. Water flows out of the frother.

You can interrupt rinsing of the filter at any time by pressing

the maintenance button c.

The water may be slightly discoloured. This is not harmful to

health and does not affect the taste.

Rinsing of the filter stops automatically after approximately 500 ml.

HEATIN G appears on the display, then READY is

displayed. The filter is now activated.

If you are using the CLARIS Blue filter cartridge and have acti-

vated it in programming mode, you will not be able to adjust

the water hardness.

The harder the water is, the more frequently the IMPRESSA needs to be descaled. It is therefore important to adjust the water hardness.

Determining the water

Determining the water hardness

hardness

The water hardness can be adjusted on a continuous scale between 1° dH and 30° dH. This can also be deactivated, which means that the IMPRESSA will not let you know when it has to be descaled.

You can find out what the water hardness is by using the Aquadur® test strip supplied as standard.

Hold the test strip briefly (for one second) under flowing water. Shake off the water.

Wait for about one minute.

You will then be able to read the degree of water hardness from the discolouration of the Aquadur®test strip and the description on the packaging. You can now adjust the water hardness.

Page 20

2 Preparing and using for the first time

Adjusting the water

Adjusting the water hardness

hardness

Adjusting the grinder Adjusting the grinder

CAUTIONCAUTION

Example: Proceed as follows to change the water hardness from

16°dH to 25°dH.

Precondition:

k T Keep the Rotary Switch pressed until

g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

RINSE appears on

the display.

HARDNESS is displayed.

16°dH

g T Turn the Rotary Switch until 25°dH is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display to confirm the setting. HARDNESS

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

READY appears on the display.

You can adjust the grinder on a continuous scale to suit the roast of your coffee.

If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged.

Only adjust the consistency of grind when the grinder is run-

ning.

The consistency of grind setting is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms. Our recommendations:

Select a fine setting for a light roast.

If the consistency of grind is too fine, the coffee only flows

in drips from the coffee spout.

Page 21

2 Preparing and using for the first time

Select a coarse setting for a darker roast.

If the consistency of grind is too coarse, the coffee flows too

quickly from the coffee spout.

Example: Proceed as follows to change the consistency of grind during the preparation of an espresso.

Open the cover of the storage compartment.

Place a cup under the coffee spout.

T i T Touch the Espresso symbol.

1ESPRESSO is displayed for about two seconds and the

Espresso symbol is active.

READY

. T Touch the Start symbol.

The grinder starts and display. Turn the grinder adjustment switch to the desired position

while the grinder is running. The coffee will be prepared and the consistency of grind is adjusted. Close the cover of the storage compartment.

1 ESPRESSO appears on the

Switching on Switching on

Precondition: Your IMPRESSA is switched on at the power switch.

Q T Press the on/off button to switch the IMPRESSA on.

HEATING appears on the display. PRESS RINSE, the maintenance button c lights up.

Place a receptacle under the coffee spout.

T c T Press the maintenance button.

RINSING, the machine rinses.

The operation stops automatically. display.

READY appears on the

Page 22

2 Preparing and using for the first time

Switching off Switching off

When you switch your IMPRESSA off, the coffee spout is only rinsed if you have prepared a speciality coffee.

Place a receptacle under the coffee spout.

Q T Press the on/off button.

RINSING, the coffee spout is rinsed.

The IMPRESSA is switched off.

Page 23

3 Familiarising yourself with the control options

3 Familiarising yourself with the control options 3 Familiarising yourself with the control options

With the IMPRESSA, you can prepare an excellent coffee or milk speciality at the touch of a button. You also have the option of adjusting the coffee strength and temperature, as well as the amount of water to your personal taste.

This chapter will allow you to become familiar with all control options with the aid of examples. To familiarise yourself with your IMPRESSA, we recommend that you make a point of actively trying the facilities described in this chapter. You will find this is well worthwhile.

Familiarise yourself with the following control options:

Preparation at the touch of a button

One-off settings before and during preparation

Entering a permanent setting for the amount of water for the

cup size

Permanent settings in programming mode

You can interrupt the machine at any time while a speciality

coffee, hot water or steam is being prepared. To do this, press

the Rotary Switch k or the maintenance button c or touch

the Start symbol ..

The last product prepared and the corresponding coffee

strength are always active.

Preparation at the

Preparation at the touch of a button

touch of a button

If you prefer to familiarise yourself with your IMPRESSA in a

fun way on the computer, the interactive Knowledge Builder

tutorial program can be found on the Internet at

www.jura.com.

Prepare your favourite speciality coffee at the touch of a button.

All speciality coffees are prepared following this model at the touch of a button.

Page 24

3 Familiarising yourself with the control options

Preparing a speciality coffee

Preparing a speciality coffee at the touch of a button

at the touch of a button

Preparing two speciality

Preparing two speciality coffees at the touch of a

coffees at the touch of a button

button

Example: Proceed as follows to prepare one espresso. Precondition:

i T Touch the Espresso symbol.

READY is displayed.

Place an espresso cup under the coffee spout.

1 ESPRESSO is displayed for about two seconds. The

Espresso symbol is active.

READY

. T Touch the Start symbol.

Preparation will now begin. display. The pre-set amount of water flows into the cup. You can follow the current status of preparation on the progress bar. Preparation stops automatically and the display.

Example: Proceed as follows to prepare two espressi. Precondition:

i T Touch the Espresso symbol twice (within two seconds).

READY is displayed.

Place two espresso cups under the coffee spout.

1 ESPRESSO appears on the

READY appears on

2 ESPRESSI appears on the display.

. T Touch the Start symbol within two seconds while

2 ESPRESSI is displayed.

Preparation will now begin. The pre-set amount of water flows into the cups. You can follow the current status of preparation on the progress bar. Preparation stops automatically and the display.

READY appears on

One-off settings before

One-off settings before and during preparation

and during preparation

You can change the coffee strength before preparation. The follow- ing coffee strengths can be selected for 1 ristretto, 1 espresso and 1 coffee:

Mild ;

Normal :

Strong _

The pre-set amount of water can be changed during prepara-

tion by turning the Rotary Switch.

Page 25

3 Familiarising yourself with the control options

One-off settings before and during preparation always follow this model.

Changing the coffee

Changing the coffee strength before preparation

strength before preparation

Changing the amount of

Changing the amount of water during preparation

water during preparation

Example: Proceed as follows to prepare a strong cup of coffee. Precondition:

_ T Touch the Strong symbol.

READY is displayed.

Place a cup under the coffee spout.

STRONG is displayed for about two seconds. The Strong

symbol is active.

o T Touch the Coffee symbol.

1 COFFEE is displayed for about two seconds. The Coffee

symbol is active.

READY

. T Touch the Start symbol.

Preparation will now begin. play. The pre-set amount of water flows into the cup. You can follow the current status of preparation on the progress bar. Preparation stops automatically and the display.

Example: Proceed as follows to prepare a Precondition:

o T Touch the Coffee symbol.

READY is displayed.

Place a cup under the coffee spout.

1 COFFEE appears on the dis-

READY appears on

110 ML cup of coffee.

1 COFFEE is displayed for about two seconds. The Coffee

symbol is active.

READY

. T Touch the Start symbol.

Preparation will now begin. display.

g T Turn the Rotary Switch during preparation until

displayed. The set amount of water flows into the cup. Preparation stops automatically and the display.

1 COFFEE appears on the

110 ML is

READY appears on

Page 26

3 Familiarising yourself with the control options

Setting the water for

Setting the water for the cup size

the cup size

It is easy to make permanent settings for the amount of water for all speciality coffees as well as hot water and steam according to the cup size. As in the following example, adjust the amount of water once. Every time you prepare a drink in the future, this amount of water will be dispensed.

The permanent settings for adapting the amount of water to the cup size for all speciality coffees, hot water and steam follow this model.

Example: Proceed as follows to make permanent settings for the amount of water for a coffee. Precondition:

o T Touch the Coffee symbol.

. T Touch the Start symbol for about three seconds, until

. T Touch the Start symbol as soon as there is sufficient coffee

READY is displayed.

Place a cup under the coffee spout.

1 COFFEE is displayed for about two seconds. The Coffee

symbol is active.

READY

ENOUGH COFFEE ? appears on the display.

Preparation starts and the coffee flows into the cup.

in the cup. Preparation stops. amount of water for one coffee will be permanently stored.

OK appears briefly on the display. The set

READY appears on the display.

Permanent settings in

Permanent settings in programming mode

programming mode

You can alter these settings at any time by repeating the

above procedure.

You can also make permanent settings for the amount of

water for all speciality coffees in programming mode, in the

BUTTONS programme item.

You can make permanent settings in programming mode. For example, you can change product settings such as aroma and the amount of water or activate an energy saving mode. Simply by turning and pressing the Rotary Switch you can navigate through the easy-to-understand programme items and make permanent settings.

Page 27

3 Familiarising yourself with the control options

You can make the following settings with the Rotary Switch:

Programme item Sub-item Explanation

RINSE

RINSE, CLEAN, FILTER (only if filter

is activated),

Select the desired maintenance programme. If no action is taken, programming mode is exited automatically after approximately five seconds.

DE-SCALE (only if filter

is not activated)

BUTTONS

FILTER - YES w

HARDNESS

(only if filter is not activated)

ENERGY

SELECT BUTTON Select your settings for speciality coffees,

NO -

INACTIVE,

hot water and steam.

Indicate whether you operate your IMPRESSA with or without a CLARIS Blue filter cartridge.

Adjust the water hardness.T

1° dH – 30° dH

SAVE -,

Select an energy saving mode.T

SAVE w

OFF AFTER

INACTIVE, 15 MIN,

Set the time after which the IMPRESSA

should switch off automatically.

0.5 HRS – 15 HRS

RINSING

RESET

MANUAL, AUTOMATIC

PRODUCT, ALL PROD.,

Set whether the switch-on rinse should be

started manually or automatically.

Reset the permanently set values of all

products to the factory settings.

RESET ALL

INFO

Keep track of all prepared products and

view the maintenance status.

DISPLAY

LANGUAGE

EXIT

ML, OZ Select the unit for the amount of water.T

Select your language.T

Exit programming mode.T

Page 28

3 Familiarising yourself with the control options

Settings in programming mode always follow the same model.

Example: Proceed as follows to change the aroma of one espresso from Precondition:

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

i T Touch the Espresso symbol.

g T Turn the Rotary Switch until STRENGTH is displayed. k T Press the Rotary Switch to enter the programme item.

g T Turn the Rotary Switch until STANDARD is displayed. k T Press the Rotary Switch to confirm the setting.

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit the programme item.

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

INTENSIVE to STANDARD.

READY is displayed.

RINSE appears.

BUTTONS is displayed.

SELECT BUTTON

Next select the product for which you would like to make settings. To enter a setting for the double product, touch the corresponding symbol twice within a period of two seconds.

1 ESPRESSO is displayed for about two seconds. WATER

INTENSIVE

OK appears briefly on the display to confirm the setting. STRENGTH

BUTTONS

READY

Page 29

4 Preparation at the touch of a button 4 Preparation at the touch of a button

In this chapter you will find out how to prepare coffee and milk specialities and hot water without making further settings.

Chapter 3, ‘Familiarising yourself with the control options’, will teach you how to adjust the settings to your personal preferences. Alternatively, you can use Chapter 5, ‘Permanent settings in programming mode’.

You can interrupt the machine at any time while a speciality

coffee, hot water or steam is being prepared. To do this, press the Rotary Switch k or the maintenance button c or touch the Start symbol .. You can select the coffee strength of individual products

before preparation: mild ;, normal : or strong _. During preparation, you can change the pre-set amount of

water by turning the Rotary Switch.

You can also try out the preparation of speciality coffees

online. Visit the Knowledge Builder at www.jura.com.

4 Preparation at the touch of a button

Ristretto, espresso

Ristretto, espresso and coffee

and coffee

All speciality coffees (ristretto u, espresso i and coffee o) are prepared in the same way.

Example: Proceed as follows to prepare one coffee.

Place a cup under the coffee spout.

o T Touch the Coffee symbol.

1 COFFEE is displayed for about two seconds. The Coffee

symbol is active.

READY

. T Touch the Start symbol.

1 COFFEE appears on the dis-

READY appears on

Page 30

4 Preparation at the touch of a button

Preparing two speciality

Preparing two speciality coffees at the touch of

coffees at the touch of a button

a button

Cappuccino Cappuccino

To prepare two cups of coffee: Place two cups under the coffee spout and touch the Coffee symbol o twice (within two seconds). Touch the Start symbol . within two seconds to start preparation.

For a cappuccino you must first froth the milk using the cappuccino frother. You then prepare an espresso straight into the milk foam.

The following procedure applies to both the Professional and Easy Cappuccino Frothers.

Remove the protective cover from the frother.

Attach the milk pipe to the frother.

Insert the other end of the milk pipe into a milk carton or connect it to a milk container.

Place a cup under the frother.

If you are using the Professional Cappuccino Frother, set the selector switch to the milk foam position p.

n T Touch the Steam symbol.

HEATING

As soon as the machine has heated up, READY appears.

n T Touch the Steam symbol again.

STEAM, the milk foam is prepared. You can follow the cur-

rent status of preparation on the progress bar. Preparation stops automatically when the pre-set amount of steam is reached.

The milk foam preparation can be interrupted at any time. To do this, press the Rotary Switch k or the maintenance button c or touch the Start symbol ..

You can prepare more milk foam within about 40 seconds without having to wait for the machine to heat.

Page 31

4 Preparation at the touch of a button

Place the cup under the coffee spout.

i T Touch the Espresso symbol.

1 ESPRESSO is displayed for about two seconds. The

Espresso symbol is active.

READY

. T Touch the Start symbol.

Preparation will now begin. display. The pre-set amount of water flows into the cup. Preparation stops automatically and the display.

To make sure the cappuccino frother always works properly, rinse and clean it regularly (see Chapter 6, ‘Maintenance – Cappuccino frother’).

1 ESPRESSO appears on the

READY appears on

Pre-ground Coffee Pre-ground Coffee

You can choose a second coffee variety, for example decaffeinated coffee, with the filler funnel for pre-ground coffee.

Never add more than two level measuring spoons of preground coffee.

Use pre-ground coffee which is not ground too finely. Very fine coffee can block up the system so that the coffee only comes out in drips.

If you did not fill the machine with a sufficient amount of preground coffee, and the IMPRESSA stops operation.

The desired speciality coffee must be prepared within approximately one minute after filling with the pre-ground coffee. Otherwise the IMPRESSA stops the operation and is ready for use again.

All speciality coffees with pre-ground coffee are prepared following this model.

Example: Proceed as follows to prepare a cup of coffee using preground coffee.

Place a cup under the coffee spout.

Open the cover of the storage compartment, take out the measuring spoon for pre-ground coffee and close the cover again.

NOT ENOUGH PRE-GROUND is displayed

Page 32

4 Preparation at the touch of a button

Foaming and

Foaming and heating milk with

heating milk with the Professional

the Professional Cappuccino Frother

Cappuccino Frother

Open the cover of the filler funnel for pre-ground coffee.

FILL PRE-GROUND

Place one level measuring spoon of pre-ground coffee into the filler funnel.

Close the cover of the filler funnel for pre-ground coffee.

SELECT BUTTON

o T Touch the Coffee symbol.

1 COFFEE appears on the display.

. T Touch the Start symbol.

Preparation will now begin. The pre-set amount of water flows into the cup. You can follow the current status of preparation on the progress bar. Preparation stops automatically and the display.

Remove the protective cover from the frother.

Attach the milk pipe to the frother.

Insert the other end of the milk pipe into a milk carton or connect it to a milk container.

READY appears on

Place a cup under the frother.

Turn the selector switch of the frother to the milk foam position p.

If you want to heat the milk, set the selector switch of the frother to the milk position t.

n T Touch the Steam symbol.

HEATING

As soon as the machine has heated up, READY appears.

n T Touch the Steam symbol again.

STEAM, the milk foam is prepared. You can follow the cur-

rent status of preparation on the progress bar.

Page 33

Foaming milk with

Foaming milk with the Easy Cappuccino

the Easy Cappuccino Frother

Frother

4 Preparation at the touch of a button

Preparation stops automatically when the pre-set amount of steam is reached.

The milk foam preparation can be interrupted at any time. To do this, press the Rotary Switch or the maintenance button or touch the Start symbol.

You can prepare more milk foam or heat the milk within about 40 seconds without having to wait for the machine to heat.

To make sure the cappuccino frother always works properly, rinse and clean it regularly (see Chapter 6, ‘Maintenance – Cappuccino frother’).

Remove the protective cover from the frother.

Attach the milk pipe to the frother.

Insert the other end of the milk pipe into a milk carton or connect it to a milk container.

Place a cup under the frother.

n T Touch the Steam symbol.

HEATING

As soon as the machine has heated up, READY appears.

n T Touch the Steam symbol again.

STEAM, the milk foam is prepared. You can follow the cur-

rent status of preparation on the progress bar. Preparation stops automatically when the pre-set amount of steam is reached.

The milk foam preparation can be interrupted at any time. To do this, press the Rotary Switch or the maintenance button or touch the Start symbol.

You can prepare more milk foam within about 40 seconds without having to wait for the machine to heat.

Page 34

4 Preparation at the touch of a button

To make sure the cappuccino frother always works properly, rinse and clean it regularly (see Chapter 6, ‘Maintenance – Cappuccino frother’).

Hot water Hot water

CAUTIONCAUTION

To obtain a perfect water flow, use the removable hot water nozzle. You can find the hot water nozzle under the cover of the storage compartment.

The following temperatures can be selected for preparing hot water:

Regular

Normal

Hot

There is a danger of scalding from hot water splashes.

Avoid direct contact with the skin.

First attach the hot water nozzle:

Carefully remove the cappuccino frother from the Connec tor

System Open the cover of the storage compartment, take out the

by twisting slightly.

hot water nozzle and close the cover again. Attach the hot water nozzle to the Connector System

rotating it slightly. Place a cup under the hot water nozzle.

m T Touch the Hot water symbol.

WATER appears on the display, and the temperature is

briefly displayed, e.g.

NORMAL.

By touching the Hot water symbol several times (within approximately 2 seconds) you can set the temperature to

your individual preference. This setting is not saved.

Hot water flows into the cup. You can follow the current status of preparation on the progress bar. Preparation stops automatically and

READY appears on

the display.

During preparation, you can change the amount by turning

the Rotary Switch.

Page 35

5 Permanent settings in programming mode 5 Permanent settings in programming mode

5 Permanent settings in programming mode

Products Products

Product Amount Strength Temperature

1 ristretto 2 ristretti 25 ML – 240 ML

1 espresso 25 ML – 240 ML STANDARD, INTENSIVE NORMAL, HIGH 2 espressi 25 ML – 240 ML

1 coffee 25 ML – 240 ML STANDARD, INTENSIVE NORMAL, HIGH 2 coffees 25 ML – 240 ML

Hot water 25 ML – 240 ML – REGULAR, NORMAL,

25 ML – 240 ML STANDARD, INTENSIVE NORMAL, HIGH

(per cup)

With the BUTTONS programme item you can enter individual settings for all speciality coffees, hot water and steam.

The following permanent settings can be made:

–

NORMAL, HIGH

HOT

Steam 3 SEC – 120 SEC ––

Permanent settings in programming mode always follow the same model.

Example: Proceed as follows to change the amount of water for 1 coffee from

100 ML to 120 ML and the temperature from

NORMAL to HIGH.

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

BUTTONS is displayed.

RINSE appears.

SELECT BUTTON

Next select the product for which you would like to make settings. To enter a setting for the double product, touch the corre-

sponding symbol twice within a period of two seconds.

Page 36

5 Permanent settings in programming mode

o T Touch the Coffee symbol.

k T Press the Rotary Switch to enter the programme item.

g T Turn the Rotary Switch until k T Press the Rotary Switch to confirm the setting.

g T Turn the Rotary Switch until TEMP. is displayed. k T Press the Rotary Switch to enter the programme item.

g T Turn the Rotary Switch until HIGH is displayed. k T Press the Rotary Switch to confirm the setting.

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit the programme item.

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

1 COFFEE is displayed for about two seconds. WATER

100 ML (example)

120 ML is displayed.

OK appears briefly on the display. WATER

NORMAL

OK appears briefly on the display. TEMP.

BUTTONS

READY

Energy Save Mode Energy Save Mode

In the programme item ENERGY you can permanently set an energy saving mode (Energy Save Mode, E.S.M.

SAVE -

All coffee products as well as hot water can be prepared without having to wait. Before steam preparation, the machine heats up.

SAVE w

Approximately five minutes after the last preparation the IMPRESSA switches to the energy-saving temperature and is not in stand-by mode. When the machine is at energy saving temperature, this is indicated on the display by the message

Before the preparation of coffee, hot water or steam, the machine heats up.

ENERGY ON.

Page 37

5 Permanent settings in programming mode

Example: Proceed as follows to change the energy saving mode

from

SAVE - to SAVE w.

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

ENERGY - is displayed.

RINSE appears.

SAVE -

g T Turn the Rotary Switch until SAVE w is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display. ENERGY w

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

READY

Automatic switch-off Automatic switch-off

By instructing your IMPRESSA to automatically switch itself off, you can cut down your energy consumption. If this function is activated, your IMPRESSA switches off automatically after the pre-set time following the last action on the machine.

You can set the automatic switch-off to 15 minutes, 0.5 hours

up to 15 hours, or inactive.

Example: Proceed as follows to change the automatic switch-off from

1 HRS to 15 MIN.

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

OFF AFTER is displayed.

RINSE appears.

1 HRS

f T Turn the Rotary Switch until 15 MIN is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display. OFF AFTER

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

READY

Page 38

5 Permanent settings in programming mode

RinsingRinsing

Restore factory

Restore factory settings

settings

You can set whether the switch-on rinse should be started manually or automatically.

Example: Proceed as follows to specify that the switch-on rinse should be started automatically after switching on.

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

RINSING is displayed.

RINSE appears.

MANUAL

g T Turn the Rotary Switch until AUTOMATIC is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display. RINSING

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

READY

In the programme item RESET you can restore various settings to their factory settings:

PRODUCT

The settings (amount of water, strength, temperature) for any product can be restored individually to the factory settings. The corresponding double product is reset at the same time.

ALL PROD.

The settings (amount of water, strength, temperature) for all products are restored to the factory settings.

RESET ALL

All customer settings are restored to the factory settings. The IMPRESSA then switches off.

Example: Proceed as follows to restored the values for

the factory settings.

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

RESET is displayed.

RINSE appears.

‘Espresso’ to

PRODUCT

Page 39

Viewing information

Viewing information and maintenance

and maintenance status

status

5 Permanent settings in programming mode

i T Touch the Espresso symbol.

OK appears briefly on the display, the settings for ‘Espresso’

are restored to the factory settings.

PRODUCT

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit the programme item.

RESET

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

READY

In the programme item INFO you can query the following information:

Number of prepared speciality coffees, hot water and steam

Maintenance status and number of maintenance programmes

performed (cleaning, descaling, changing the filter) Software version

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

INFO is displayed.

RINSE appears.

BUTTONS

k T Press the Rotary Switch to enter the programme item.

The total number of the prepared speciality coffees is displayed.

By touching the individual symbols for the speciality coffees,

hot water and steam, the respective number of prepared products is displayed. To query the number of double products prepared, touch the

corresponding symbol for the speciality coffee twice. Open the cover of the filler funnel for pre-ground coffee to

query this number.

k T Press the Rotary Switch to exit the programme item.

BUTTONS

g T Turn the Rotary Switch until CLEAN is displayed.

Page 40

5 Permanent settings in programming mode

k T Press the Rotary Switch to enter the programme item.

k T Press the Rotary Switch to exit the programme item.

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit the programme item.

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

Continue turning the Rotary Switch to switch to the per-

formed descaling and filter change operations.

The number of performed cleaning operations appears on the display.

By turning the Rotary Switch, the maintenance status can also be displayed in addition to the number of performed maintenance programmes. The filled out fields show the maintenance status. Once all fields are filled out, your IMPRESSA will request the respective maintenance programme.

CLEAN

INFO

READY

Unit, amount of waterUnit, amount of water

You can change the unit for the amount of water from ‘ml’ to ‘oz’.

Example: Proceed as follows to change the unit for the amount of water from

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

ML to OZ.

RINSE appears.

DISPLAY is displayed.

g T Turn the Rotary Switch until OZ is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display. DISPLAY

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

READY

Page 41

5 Permanent settings in programming mode

Language Language

The language of your IMPRESSA is set with this programme item.

Example: Proceed as follows to change the language from

ENGLISH to DEUTSCH.

Precondition:

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

RINSE appears.

LANGUAGE is displayed.

ENGLISH

g T Turn the Rotary Switch until DEUTSCH is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display. SPRACHE

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

BEREIT

Page 42

6 Maintenance

6 Maintenance6 Maintenance

Your IMPRESSA has the following integrated maintenance programmes:

Rinsing the machine

Changing the filter

Cleaning the machine

Descaling the machine

Clean or descale the machine or change the filter when you

are prompted to do so.

Maintenance tips Maintenance tips

Rinsing the machine Rinsing the machine

To ensure that you get many years of reliable service out of your IMPRESSA and to guarantee the optimum coffee quality, the machine requires daily maintenance.

Proceed as follows:

Empty the coffee grounds container and the drip tray. Rinse

them with warm water. Rinse the water tank with clean water.

Dismantle and rinse the frother (see Chapter 6, ‘Maintenance

– Dismantling and rinsing the cappuccino frother’). Wipe the surface of the machine with a clean, soft, damp cloth

(e.g. microfibre cloth).

When the IMPRESSA is switched on, a prompt to perform rinsing appears after heating, or this is automatically started. It can be set in programming mode whether the switch-on rinse needs to be activated manually or whether the machine automatically activates the switch-on rinse (see Chapter 5, ‘Permanent settings in programming mode - Rinses’).

When the IMPRESSA is switched off, a rinse operation is automatically initiated.

You can initiate the rinse operation manually at any time.

Page 43

6 Maintenance

Precondition: READY is displayed.

Place a receptacle under the coffee spout.

k T Keep the Rotary Switch pressed until k T Press the Rotary Switch to enter the programme item.

RINSE appears.

RINSE

k T Press the Rotary Switch to initiate the rinse operation.

RINSING, water flows out of the coffee spout.

Rinsing stops automatically and your IMPRESSA is then ready for use.

Changing the filter Changing the filter

Changing after a promptChanging after a prompt

After 50 litres of water have flowed through, the filter will cease to work. Your IMPRESSA will automatically prompt you to change the filter. After two months, the filter will cease to work. You can check

the elapsed time by referring to the date plate on the cartridge holder in the water tank. If the CLARIS Blue filter cartridge is not activated, you will not

be prompted to change the filter.

You can also try out the ‘changing the filter’ operation online.

Visit the Knowledge Builder at www.jura.com.

Proceed as follows to change the CLARIS Blue filter cartridge when prompted to do so by your IMPRESSA.

Precondition: nance button c lights up. c T Press the maintenance button.

READY / FILTER is displayed and the mainte-

CHANGE

Remove and empty the water tank.

Lift the cartridge holder.

Take out the old filter cartridge and the extension.

Fit the extension on top of a new filter cartridge.

Page 44

6 Maintenance

Insert the filter cartridge into the water tank, exerting slight pressure. Close the cartridge holder. It will click into place audibly.

Fill the water tank with fresh, cold water and reinsert the

tank.

Place a receptacle (at least 500 ml) under the frother.

If you are using the Professional Cappuccino Frother, set the

selector switch of the frother to the steam position n.

c T Press the maintenance button.

FILTER RINSING, water will flow out of the frother.

You can interrupt rinsing of the filter at any time. To this pur-

pose press the maintenance button c. The water may be slightly discoloured. This is not harmful to

health and does not affect the taste.

Rinsing of the filter stops automatically after approximately 500 ml. The IMPRESSA heats up and is once more ready for use.

Changing the filter

Changing the filter manually

manually

You can initiate the ‘Changing the filter’ operation manually.

Precondition: The filter is activated and

k T Keep the Rotary Switch pressed until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

RINSE appears.

RINSE

g T Turn the Rotary Switch until FILTER is displayed. k T Press the Rotary Switch.

CHANGE

Continue with the second prompt to take action (indicated

by a T), as is described under ‘Changing after a prompt’.

Page 45

6 Maintenance

Cleaning the machine Cleaning the machine

CAUTIONCAUTION

Cleaning after a promptCleaning after a prompt

After 200 coffee preparations or 80 switch-on rinses, the IMPRESSA will prompt you to clean it.

If the wrong cleaning agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water.

Use only original JURA maintenance products.

The cleaning programme only lasts about 20 minutes.

Do not interrupt the cleaning programme. The quality of

cleaning will be impaired if you do so. JURA cleaning tablets are available from stockists.

You can also try out the ‘Cleaning the machine’ operation

online. Visit the Knowledge Builder at www.jura.com.

Precondition: button c lights up. c T Press the maintenance button.

READY / CLEAN is displayed and the maintenance

EMPTY TRAY

Empty the drip tray and coffee grounds container and put them back into the machine.

PRESS RINSE, the maintenance button c lights up.

Place a receptacle under the coffee spout.

c T Press the maintenance button.

CLEANING, water flows out of the coffee spout.

The operation is interrupted,

Open the cover of the filler funnel for pre-ground coffee.

ADD TABLET.

Insert a JURA cleaning tablet into the filler funnel.

Close the cover of the filler funnel.

PRESS RINSE, the maintenance button c lights up.

c T Press the maintenance button.

CLEANING, water flows out of the coffee spout several

times. The operation is interrupted,

Empty the drip tray and coffee grounds container and put them back into the machine.

EMPTY TRAY.

Page 46

6 Maintenance

The cleaning operation is now complete. The IMPRESSA is once more ready for use.

Manual cleaningManual cleaning

Descaling the machine Descaling the machine

CAUTIONCAUTION

You can initiate the ‘Cleaning the machine’ operation manually.

Precondition:

k T Keep the Rotary Switch pressed until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

RINSE appears.

RINSE

g T Turn the Rotary Switch until CLEAN is displayed. k T Press the Rotary Switch.

EMPTY TRAY

Continue with the second prompt to take action (indicated by a T), as is described under ‘Cleaning after a prompt’.

The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the degree of hardness of your water.

If the descaling agent comes into contact with the skin or eyes, this can cause irritation.

Avoid contact with the skin or eyes.

If descaling agent does come into contact with the skin or eyes, rinse off with clean water. Should you get any descaling agent in your eye, see a doctor.

CAUTIONCAUTION

If the wrong descaling agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water.

Use only original JURA maintenance products.

If the descaling operation is interrupted, there may be damage to the machine.

Allow the descaling programme to run to the end.

If the descaling agent comes into contact with sensitive surfaces, damage cannot be ruled out.

Clean up any splashes immediately.

Page 47

6 Maintenance

The descaling programme lasts approx. 45 minutes.

JURA descaling tablets are available from stockists.

If you use a CLARIS Blue filter cartridge and this is activated,

you will not be prompted to descale.

You can also try out the ‘Descaling the machine’ operation

online. Visit the Knowledge Builder at www.jura.com.

Descaling after a promptDescaling after a prompt

Precondition:

READY / DE-SCALE is displayed and the mainte-

nance button c lights up. c T Press the maintenance button.

EMPTY TRAY

Empty the drip tray and coffee grounds container and put them back into the machine.

AGENT IN TANK

Remove and empty the water tank.

Completely dissolve the contents of one blister (three JURA descaling tablets) in a container that holds 500 ml of water. This may take several minutes. Pour the solution into the empty water tank and insert it in

the machine.

AGENT IN TANK, the maintenance button c lights up.

Remove the cappuccino frother from the Connector

System

Place a receptacle (at least 500 ml) under the Connector System

c T Press the maintenance button.

DE-SCALING

This causes water to flow out of the Connector System© several times. The maintenance button blinks during the descaling operation. The operation stops automatically,

Empty the receptacle under the Connector System

Empty the drip tray and coffee grounds container and put

EMPTY TRAY.

them back into the machine.

FILL WATER TANK

Remove the water tank and rinse it thoroughly.

Page 48

6 Maintenance

Fill the water tank with fresh, cold water and reinsert the tank.

PRESS RINSE, the maintenance button c lights up.

Replace the cappuccino frother.

Place a receptacle under the frother and another under the coffee spout.

c T Press the maintenance button.

DE-SCALING, water flows out of the frother and the

coffee spout. The operation stops automatically,

Empty the drip tray and coffee grounds container and put them back into the machine. The descaling operation is now complete. Your IMPRESSA heats up and is once more ready for use.

If the descaling operation stops unexpectedly, rinse the water tank thoroughly.

EMPTY TRAY.

Manual descalingManual descaling

Rinsing the

Rinsing the cappuccino frother

cappuccino frother

You can initiate the ‘Descaling the machine’ operation manually.

Precondition:

k T Keep the Rotary Switch pressed until k T Press the Rotary Switch to enter the programme item.

READY is displayed and the filter is not activated.

RINSE appears.

RINSE

g T Turn the Rotary Switch until DE-SCALE is displayed. k T Press the Rotary Switch.

EMPTY TRAY

Continue with the second prompt to take action (indicated by a T), as is described under ‘Descaling after a prompt’.

This chapter applies to the Professional and Easy Cappuccino Frothers.

To ensure that the cappuccino frother works perfectly, you should rinse it with water after every milk preparation. Your IMPRESSA will

not prompt you to rinse the cappuccino frother.

Page 49

Cleaning the

Cleaning the cappuccino frother

cappuccino frother

6 Maintenance

Precondition: READY is displayed.

Remove the milk pipe from the milk carton/bottle or the milk container.

Fill a receptacle with fresh water and immerse the milk pipe in it.

Place a receptacle under the cappuccino frother.

If you are using the Professional Cappuccino Frother, turn the selector switch to the milk foam p or milk t position.

n T Touch the Steam symbol.

HEATING

As soon as the machine has heated up, READY appears.

n T Touch the Steam symbol again.

STEAM, the frother and milk pipe are rinsed.

. T Touch the Start symbol as soon as clean water flows out of

the frother. The operation stops and your IMPRESSA is once more ready for use.

This chapter applies to the Professional and Easy Cappuccino Frothers.

CAUTIONCAUTION

To ensure that the cappuccino frother works perfectly, you should clean it daily when you have been preparing milk. Your IMPRESSA will not prompt you to clean the cappuccino frother.

If the wrong cleaning agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water.

Use only original JURA maintenance products.

JURA Cappuccino Cleaner is available from stockists.

You can also try out the ‘Cleaning the cappuccino frother’

operation online. Visit the Knowledge Builder at www.jura.com.

Page 50

6 Maintenance

Precondition: READY is displayed.

Remove the milk pipe from the milk carton/bottle or the milk container.

Pour 250 ml of fresh water into a receptacle and add one capful (max. 15 ml) of Cappuccino Cleaner. Immerse the milk pipe in the receptacle.

Place another receptacle under the frother.

If you are using the Professional Cappuccino Frother, turn

the selector switch to the milk foam p or milk t position.

n T Touch the Steam symbol.

HEATING

As soon as the machine has heated up, READY appears.

n T Touch the Steam symbol again.

STEAM, the frother and milk pipe are cleaned.

. T Touch the Start symbol as soon as the receptacle containing

the Cappuccino Cleaner is empty.

Rinse the receptacle thoroughly, fill it with approx. 250 ml of fresh water and immerse the milk pipe in the water.

Empty the other receptacle and place it under the frother once more.

n T Touch the Steam symbol.

STEAM, the frother and milk pipe are rinsed with fresh

water.

. T Touch the Start symbol as soon as the receptacle containing

the water is empty. The operation stops and your IMPRESSA is once more ready for use.

Page 51

Dismantling

Dismantling and rinsing the

and rinsing the Professional

Professional Cappuccino Frother

Cappuccino Frother

Dismantling and

Dismantling and rinsing the Easy

rinsing the Easy Cappuccino Frother

Cappuccino Frother

6 Maintenance

Dismantle the frother completely.

Rinse all frother parts thoroughly under running water.

Re-assemble the frother.

Ensure that all individual parts are correctly and firmly connected to ensure correct operation of the frother

Firmly attach the frother to the Connector System

Carefully remove the frother from the Connector System by twisting slightly.

Dismantle the frother completely.

Rinse all frother parts thoroughly under running water.

Re-assemble the frother.

Ensure that all individual parts are correctly and firmly connected to ensure correct operation of the frother.

Firmly attach the frother to the Connector System

Cleaning the

Cleaning the bean container

bean container

WARNINGWARNING

Coffee beans may be covered with a slight oil film which remains on the walls of the bean container. These residues may negatively affect the coffee results. For this reason clean the bean container from time to time.

Danger of injury to the fingers when the grinder is running.

Switch the machine off with the on/off button Q before performing any work on the grinder.

Switch the machine off at the power switch 3 .

Open the bean container cover and remove the aroma preservation cover.

Page 52

6 Maintenance

Descaling

Descaling the water tank

the water tank

Loosen the screw in the bean container and lift up the finger

protection. Remove the remaining beans with a vacuum cleaner.

Clean the bean container with a soft, dry cloth.

Put the finger protection down again and screw it back

tightly in place.

Fill the bean container with coffee beans.

Close the aroma preservation cover and the bean container cover.

Limescale deposits may form in the water tank. To ensure correct function of the machine, descale the water tank from time to time.

Remove the water tank.

If you use a CLARIS Blue filter cartridge, remove this.

Descale the tank with a mild conventional descaling agent in accordance with the manufacturer’s instructions.

Rinse out the water tank thoroughly.

If you use a CLARIS Blue filter cartridge, insert this again.

Fill the water tank with fresh, cold water and reinsert the tank.

Page 53

7 Display messages

Message Cause/Result Action

FILL WATER TANK

EMPTY GROUNDS

EMPTY TRAY

TRAY MISSING

FILL BEANS

The water tank is empty. You cannot prepare any speciality coffee or hot water or steam.

The coffee grounds container is full. You cannot prepare any speciality coffees, but you can prepare hot water or steam.

The drip tray is full. You cannot prepare any speciality coffees or hot water or steam.

The drip tray is not inserted correctly or is not inserted at all. You cannot prepare any speciality coffees or hot water or steam.

The bean container is empty. You cannot prepare any speciality coffees with beans. You can prepare preground coffee, hot water and steam.

READY / CLEAN After 200 preparations or 80 switch-

on rinses, the IMPRESSA will prompt you to clean it.

READY / DE-SCALE

READY / FILTER

The IMPRESSA is prompting you to descale it.

After 50 litres of water have flowed through the filter cartridge, it will cease to work.

Fill the water tank (See Chapter 2, ‘Preparing and using for the first time – Filling the water tank’).

Empty the coffee grounds

container and the drip tray.

Empty the drip tray.T

Insert the drip tray.T

Fill the bean container (See Chapter 2, ‘Preparing and using for the first time – Filling the bean container’).

Clean the machine (See Chapter 6, ‘Maintenance – Cleaning the machine’).

Descale the machine (See Chapter 6, ‘Maintenance – Descaling the machine’).

Replace the CLARIS Blue filter cartridge (see Chapter 6 ‘Maintenance – Changing the filter’).

7 Display messages

Page 54

7 Display messages

Message Cause/Result Action

NOT ENOUGH PRE-GROUND

TOO HOT

There is too little pre-ground coffee in the machine; the IMPRESSA stops the operation.

The system is too hot to start a maintenance programme.

The next time you prepare coffee use more pre-ground coffee (see Chapter 4 ‘Preparation at the touch of a button – Pre-ground coffee’).

Prepare a speciality coffee or hot

water.

Page 55

8 Troubleshooting

Problem Cause/Result Action

Insufficient foam is produced when the milk is frothed or milk sprays from the cappuccino frother.

Coffee only comes out in drips when it is being prepared.

Water hardness cannot be adjusted.

FILL BEANS is displayed

although the bean container has been filled.

FILL BEANS

is not displayed although the bean container is empty.

EMPTY TRAY

is always displayed.

The cappuccino frother is dirty.

Coffee or pre-ground coffee has been ground too finely and is blocking the system.

The CLARIS Blue filter cartridge is activated.

The grinder is not yet completely filled with beans.

The bean monitor is dirty.

The metal contacts of the drip tray are dirty or wet.

Rinse and clean the cappuccino

frother(see Chapter 6,

‘Maintenance – Cappuccino

frother’).

Put the grinder on a coarser setting or use coarser pre-ground coffee (refer to Chapter 2, ‘Preparing and using for the first time – Adjusting the grinder’).

Deactivate the filter cartridge in

programming mode.

Prepare a speciality coffee.T

Clean the bean container (see Chapter 6, ‘Maintenance – Cleaning the bean container’).

Clean and dry the metal contacts on the back of the drip tray.

8 Troubleshooting

FILL WATER TANK

is displayed although the water tank is full.

Grinder is making a very loud noise.

The water tank float is trapped.

There are foreign objects in the grinder.

Descale the water tank (see Chapter 6, ‘Maintenance – Descaling the water tank’).

Contact Customer Support in your country (see Chapter ‘JURA contact details / Legal information’).

Page 56

8 Troubleshooting

Problem Cause/Result Action

Little or no water or steam comes out of the frother. The pump is very quiet.

The Connector System may be blocked by milk residues or descaling fragments loosened during descaling.

Remove the frother from the Connector System

Unscrew the black connector with the aid of the hexagonal hole on the measuring spoon for pre-ground coffee.

Clean the connector thoroughly.

Manually screw the connector back on to the Connector System

Carefully tighten it using the hexagonal hole on the measuring spoon, turning by no more than a quarter of a rotation.

Warm the machine at room

ERROR 2

is displayed.

If the machine was exposed to the cold for

temperature.

a long period of time, heating is disabled for safety reasons.

Other

ERROR

messages are displayed.

– Turn the IMPRESSA off at the power

switch. Contact Customer Support in your country (see Chapter ‘JURA contact details / Legal information’).

If you were unable to solve the problem, contact Customer Support in your country (see Chapter ‘JURA contact details / Legal information’).

Page 57

9 Transport and environmentally neutral disposal

9 Transport and environmentally neutral disposal 9 Transport and environmentally neutral disposal

Transport / Emptying

Transport / Emptying the system

the system

Keep the packaging for your IMPRESSA. It should be used to protect the machine during transport.

In order to protect the IMPRESSA from frost during transport, the system must be emptied.

Disposal Disposal

Precondition:

n T Touch the Steam symbol.

READY is displayed.

Carefully pull the cappuccino frother off the Connector

System

Place a receptacle under the Connector System

HEATING

As soon as the machine has heated up, READY appears.

n T Touch the Steam symbol again.

STEAM, hot steam is discharged from the Connector

System

Remove and empty the water tank. Steam will continue to be discharged from the Connector System

until the system is empty.

PRESS RINSE

Q T Press the on/off button.

The IMPRESSA is switched off.

The next time you use the machine the system must be refilled (see Chapter 2, ‘Preparing and using for the first time – First-time use’).

Please dispose of old machines in an environmentally neutral way.

Old machines contain valuable materials capable of being recycled which should be salvaged for recycling. Please therefore dispose of old machines via suitable collection systems.

Page 58

10 Technical data

Voltage

Power 1450 W Safety test Power consumption

A S F D G

S D F G

12 Wh

220 –240 V ~, 50 Hz 120 V ~, 60 Hz 220 –240 V ~, 50 Hz 220 V ~, 50 Hz

ENERGY SAVE -

Power consumption

7 Wh

ENERGY SAVE w.

Pump pressure Static max. 15 bar Holding capacity of water tank 2,1 l Holding capacity

of bean container Holding capacity of coffee

grounds container Cable length Approx. 1,1 m Weight 10,75 kg Dimensions (W x H x D) 28,5 x 34,2 x 43,3 cm

250 g

Approx. 16 servings

Page 59

Index A

Amount

Changing the amount of water during preparation 25 Entering a permanent setting for the amount of water for the cup size 26

Amount of coffee

Changing the amount of water during preparation 25 Entering a permanent setting for the amount of water for the cup size 26

Amount of water

Changing during preparation 25 Setting the water for the cup size 26

Automatic switch-off 37

Bean container 8

Cleaning 51 Filling 17

Bus bar

Technical data 58

Cappuccino 30 Cappuccino frother

Cleaning 49 Easy Cappuccino Frother 9 Professional Cappuccino Frother 9 Rinsing 48

CLARIS Blue (filter cartridge)

Changing 43 Inserting and activating 18, 19

Cleaning

Bean container 51 Machine 45

Coffee 29 coffee

Pre-ground coffee 31

Coffee grounds container 8 Coffee strength

Changing before preparation 25

Descaling

Machine 46 Water tank 52

Display

Messages 53

Display messages 53 Disposal 57 Drip tray 8

Easy Cappuccino Frother

Dismantling and rinsing 51

Emptying the system 57 Energy Save Mode 36 Energy saving mode 14 Environmentally neutral disposal 57 Errors

Troubleshooting 55

Espresso 29

Factory settings

Restore factory settings 38

Filling

Bean container 17 Water tank 16

Filter

Changing 43 Inserting and activating 18, 19

First-time use 17 Frother

Cleaning the cappuccino frother 49 Easy Cappuccino Frother 9, 15 Professional Cappuccino Frother 9, 15 Rinsing the cappuccino frother 48

Grinder adjustment switch

Adjusting the grinder 20

Hot milk

Foaming and heating with the Professional Cappuccino Frother 32

Hot water 34 Hot water nozzle 9

Page 60

Inserting

Water tank 16

Internet 15

Knowledge Builder 15

Language 41

Machine

Cleaning 45 Descaling 46 Rinsing 42 Setting up 16 Switching off (Standby) 22 Switching on 21

Maintenance

Maintenance button 9 Maintenance tips 42

Milk

Foaming and heating with the Professional Cappuccino Frother 32 Foaming with the Easy Cappuccino Frother 33

Milk foam

With the Easy Cappuccino Frother 33 With the Professional Cappuccino Frother 32

Nozzle

Hot water nozzle 9

One-off settings before and during

preparation 24

Permanent settings in programming

mode 35

Pre-ground coffee 31

Preparation

At the touch of a button 29 Cappuccino 30 Coffee 29 Espresso 29

Hot water 34 Pre-ground coffee 31 Ristretto 29

Problems

Troubleshooting 55

Professional Cappuccino Frother 15

Dismantling and rinsing 51

Programming mode 35

Automatic switch-off 37 Language 41 Permanent settings in programming mode 26 Products 35 Reset settings to factory settings 38

Rinsing

Machine 42

Ristretto 29

Safety information 10 Settings

Entering a permanent setting for the amount of water for the cup size 26 One-off settings before and during preparation 24 Permanent settings in programming mode 35

Setting up 16 Supplied as standard 16 Switching off 22 Switching on 21

Technical data 58 Transport 57 Troubleshooting 55

Viewing information and maintenance

status 39

Viewing maintenance status 39

Water tank 8

Descaling 52 Filling 16

Page 61

616263

Page 62

Page 63

Page 64

Art. 68817/J7/en/200908

JURA contact details / Legal informationJURA contact details / Legal information

JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Tel.: +41 62 38 98 233

Further contact information is available on the company website at www.jura.com.

DirectivesDirectives

Technical changesTechnical changes

FeedbackFeedback

CopyrightCopyright

The machine complies with the following EU directives:

2006/95/EG – Low Voltage Directive

2004/108/EG – Electromagnetic Compatibility

2005/32/EG – Energy Directive

We reserve the right to make technical changes.

The illustrations used in the IMPRESSA J7 Manual show the IMPRESSA J7 Piano Black. Your IMPRESSA could incorporate minor changes.

Your opinion is important to us! Use the contact link at www.jura.com.

The Instructions for Use contain information which is protected by copyright. It is not permitted to photocopy or translate these Instructions for Use into another language without the express written consent of JURA Elektroapparate AG.