JRC JHS-180 Instruction Manual

Automatic Identification System

JHS-180

Instruction Manual

7ZPJD0173A

i

Preface

Thank you for purchasing JHS-180 Automatic Identification System.

JHS-180 is the Class A shipborne equipment of the universal Automatic Identification System.

• Be sure to read this manual for full comprehension before using the equipment.

• Save this manual near at hand for quick reference in the future.

Make use of this manual when experiencing operation difficulties.

ii

WARNING

Before Operation

Concerning the symbols

This manual uses the following symbols to explain correct operation and to prevent
injury or damage to property.
The symbols and descriptions are as follows. Understand them before proceeding with
this manual.

Indicates a warning that, if ignored, may
result in serious injury or even death.

Indicates a caution that, if ignored, may
result in injury or damage to property.

Examples of symbols

The △ symbol indicates caution (including DANGER and WARNING).
The illustration inside the △ symbol specifies the content of the caution
more accurately. (This example warns of possible electrical shock.)

The symbol indicates that performing an action is prohibited.
The illustration inside the symbol specifies the contents of the
prohibited operation. (In this example disassembly is prohibited.)

The ● symbol indicates operations that must be performed.
The illustration inside the ● symbol specifies obligatory instructions. (In
this example unplugging is the obligatory instruction.)

Concerning warning labels

A warning label is pasted to the top cover of this product.
Do not remove, damage or modify the label.

CAUTION

iii

WARNING

Handling Precautions

Do not disassemble or customize this unit. Doing so may cause fire,
electrical shock or malfunction.

Do not use a voltage other than specified. Doing so may cause fire,
electrical shock or malfunction.

Do not touch any parts where this warning label is pasted. Doing so may
cause electrical shock.

iv

CAUTION

Handling Precautions

Do not use this equipment for anything other than specified.
Doing so may cause malfunction or damage to persons.

Do not turn the trimmer resistors or the trimmer capacitors on the PCB unit,
except when and if they need to be adjusted.
Doing so may cause malfunction or damage to persons. They are preset at
the factory.

Do not install this equipment in a place other than specified or in one with
excessive humidity, steam, dust or soot. Doing so may cause fire, electric
shock, malfunction or damage to persons.

Do not get this equipment wet or spill any liquids on or near this equipment.
Doing so may cause electrical shock or malfunction.

Do not place this equipment anywhere vibration or impact is likely to occur.
Doing so may cause a fall or damage to property and persons.

v

External Views

NTE-180 AIS Transponder

NCM-722 AIS Controller

vi

NQD-4190 Junction Box

NQE-3111 Connection Box

vii

NBD-577A Power Supply Unit

viii

CONTENTS

Preface .................................................................................................................. i

Before Operation .....................................................................................................ii

Handling Precautions ............................................................................................. iii

CAUTIONS AGAINST HIGH VOLTAGE ................................................................ v

Cautions concerning treatment of electrocution victims ........................................ v

First aid ..................................................................................................................vi

External Views .......................................................................................................ix

CONTENTS ......................................................................................................... xiii

Abbreviations ........................................................................................................xv

1.GENERAL ........................................................................................

1-1

1.1 Outlines ..................................................................................................... 1-1

1.2 Features .................................................................................................... 1-1

1.3 Components .............................................................................................. 1-2

1.3.1 Standard Components ...................................................................... 1-2

1.3.2 Options .............................................................................................. 1-2

1.4 Configration ............................................................................................... 1-3

2.INSTALLATIONDIAGRAM ...............................................................2-1

3.PART NAMES AND FUNCTIONS ................................................... 3-1

4.DISPLAYS .......................................................................................3-1

5.OPERATION ....................................................................................

5-1

5.1 MENU TABLE.............................................................................................. 5-1

5.2 BASIC OPERATION.................................................................................... 5-2

5.2.1 Turning the power ON................................................................................ 5-2

5.2.1.1 Other Ships List..................................................................................... 5-2

5.2.1.2 Other Ship's Detail Information.............................................................. 5-3

5.2.2 Turning the power OFF.............................................................................. 5-4

5.2.3 Alarm.......................................................................................................... 5-5

5.2.3.1 Guard zone alarm ................................................................................. 5-5

5.2.3.2 Lost target alarm ................................................................................... 5-5

5.3 MAIN MENU ................................................................................................... 5-6

5.3.1 Message Menu .......................................................................................... 5-7

5.3.1.1 Edit and TX ........................................................................................... 5-8

5.3.1.2 TX Tray................................................................................................ 5-10

5.3.1.3 RX Tray............................................................................................... 5-12

5.3.1.4 Interrogation ........................................................................................ 5-13

5.3.1.5 Long Range Message......................................................................... 5-15

5.3.2 Destination Setting................................................................................... 5-16

5.3.2.1 Destination .......................................................................................... 5-17

ix

5.3.2.2 Waypoint Text ......................................................................................5-18

5.3.2.3 Estimated Time of Arrival (ETA) ...........................................................5-19

5.3.2.4 Waypoints ............................................................................................5-20

5.3.3 Navigation Information Setting .................................................................5-21

5.3.3.1 Navigational Status Information ...........................................................5-21

5.3.3.2 Persons On-Board ...............................................................................5-21

5.3.3.3 Type of Ship and Cargo Type ..............................................................5-22

5.3.3.4 Draught................................................................................................5-23

5.3.3.5 Height Over Keel .................................................................................5-23

5.3.4 Alarm Setting ............................................................................................5-24

5.3.4.1 Range ..................................................................................................5-24

5.3.4.2 Lost Target ...........................................................................................5-24

5.3.5 Group Ship Setting ...................................................................................5-25

5.3.5.1 Ship Name...........................................................................................5-25

5.3.5.2 MMSI ...................................................................................................5-25

5.3.6 Setup menu ..............................................................................................5-26

5.3.6.1 Password Setting.................................................................................5-27

5.3.6.2 Channel Management Setting .............................................................5-28

5.3.6.3 Own Ship Data display setting .............................................................5-32

5.3.6.4 Long Range Response setting.............................................................5-32

5.3.6.5 Contrast setting....................................................................................5-33

5.3.6.6 Number of Retries Setting ...................................................................5-33

5.3.7 Maintenance menu ...................................................................................5-34

5.3.7.1 TRX Condition log display....................................................................5-35

5.3.7.2 AIS Alarm display.................................................................................5-36

5.3.7.3 Sensor Status display ..........................................................................5-36

5.3.7.4 Power On/Off Log display ....................................................................5-37

5.3.7.5 Password Log ....................................................................................5-37

5.3.7.6 Software Version display......................................................................5-37

6.MAINTENANCE AND INSPECTION ................................................6-1

6.1 General Maintenance and Inspection ..........................................................6-1

6.2 Maintenance Menu ......................................................................................6-1

7.AFTER-SALES SERVICE ................................................................. 7-1

Before returning repair....................................................................................... 7-1

Periodical maintenance recommended ............................................................ 7-1

8.SPECIFICATIONS ............................................................................8-1

8.1 NTE-180 AIS Transponder......................................................................... 8-1

8.2 NCM-722 AIS Controller .......................................................................... 8-1

8.3 NBD-577A Power Supply Unit .................................................................. 8-2

1-1

1. GENERAL

1.1 Outlines

Automatic Identification System (AIS) is a maritime navigation and radio communication system.
This system intends to enhance the safety of life at sea, the safety and efficiency of navigation
and the protection of the marine environment by communicating navigational information
automatically on VHF channels between ship and ship, ship and shore.
JHS-180 meets the requirements of the SOLAS Conventions for the Class A shipborne
equipment of the universal AIS. JHS-180 mainly consists of AIS Transponder and AIS Controller.
The combined antenna and transponder design allows installation at any convenient location on
any vessels. The small and simple design controller allows easy installation and operation.
JHS-180 employs the latest technologies such as digital signal processing, circuit integration
technology, and these technologies ensure high performance and high reliability.

1.2 Features

● Fully Comply with International Regulations
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

JHS-180 is designed to meet the requirements of the SOLAS Conventions for the Class A
shipborne equipment of the universal AIS and fully complies with international regulations: IMO
MSC74(69) Annex 3, ITU-R M.1371, IEC61993-2, IEC60945 etc.

● Combined Antenna and Transponder for Ease of Installation
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

JHS-180 employs the combined antenna and transponder design. This design allows installation
at any convenient location on any vessels. For the connection between abode deck component
and below deck component, only one cable is needed.

● Increased Probability of Vessel Detection
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

JHS-180 is equipped with a guard zone alert function. When preset guard zone range and other
vessel enters into the zone, JHS-180 indicates and sounds the alert. This function enhances
probability of vessel detection.

● Recognition of Own-group Vessels
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

JHS-180 is equipped with a recognition of own-group vessels function. When preset own-group
vessels’ identification in advance, the display indicates the own-group vessel sign. This sign
allows easy recognition of own-group vessels.

● Self-diagnosis Function
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

JHS-180 is equipped with a built-in automatic self-diagnosis function. This function allows easy
maintenance and high system reliability.

● System Integration Availability
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

JHS-180 is equipped with various interfaces. These interfaces allow system integration and future
expansions.

1-2

1.3 Components

1. 3. 1 Standard Components

No. Name Type Quantity Remarks

1 AIS Transponder NTE-180 1 With 2m cable, Fitting belts
2 AIS Controller NCM-722 1
3 Power Supply Cable 7ZCJD0095 1 L=5m
4 Control Cable 1 7ZCAF0078 1 L=5m
5 Junction Box NQD-4190 1
6 Connection Box NQE-3111 1
7 Power Supply Unit NBD-577A 1
8 Spare Parts 7ZXJD0027 1 Fuses
9 Instruction Manual 1

1. 3. 2 Options

No. Options Type Quantity Remarks

1 Control Cable 2 7ZCAF0079 1 L=5m
2 Flash Mount Kit MPBP30837 1 Color: 2.5G7/2
3 Flash Mount Kit MPBP30838 1 Color: 7.5BG7/2

1-3

1.4 Configuration

• System Block Diagram

1-4

• Outline Drawing of NTE-180 AIS Transponder

━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

Unit: mm
Mass: approx. 3.3 kg

1-5

• Outline Drawing of NQD-4190 Junction Box

━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

Unit: mm
Mass: approx. 1.2 kg

1-6

• Outline Drawing of NCM-722 AIS Controller

━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

Unit: mm
Mass: approx. 2.0 kg

1-7

• Outline Drawing of NQE-3111 Connection Box

━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

Unit: mm
Mass: approx. 5.5 kg

1-8

• Outline Drawing of NBD-577A Power Supply

━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

Unit: mm
Mass: approx. 10.0 kg

2-1

2. INSTALLATION DIAGRAM

Notes:

Leave installation of this equipment to our service center or agents.
Installation by an unauthorized person may results in malfunction.

3-1

3. PART NAMES AND FUNCTIONS

(1) LCD Panel

For further information, refer to “4. Display”.

(2) Menu key

Displays the Main-menu.

(3) Arrow Keys

Move the cursor upward, downward, to the left or to the right.

(4) Numerical Keys

Input the numerical data.

(5) Enter key

Confirms the input.

(6) Alarm off/CLR key

Clears input errors.
Off the alarm sound when beeping alarm sound.

(7) Select-1 key

Displays the Other Ships List.

(8) Select-2,-3,-4 keys

Operates functions of the each Display. See the Basic Operation and the Main Menu Operation.

(9) Power/Dimmer key

Turn the power ON.
Adjusts the back light brightness of the LCD and key in four stages.
(Each time [PWR/DIM] is pressed, the display dims one stage at a time.)

(10) Power OFF key

Pressing [PWR/DIM] and [OFF] at the same time turn the power OFF.

(2) Menu key (3) Arrow Keys

(4) Numerical Keys

(5) Enter key

(6) Alarm off

/CLR key

(1) LCD Panel

(8) Select-2,3,4

keys

(9) Power/Dimmer key (10) Power OFF key(7) Select-1 key

4-1

4. DISPLAYS

Minimum other ships list (three)

Other ships list,
Other ship’s detail information
or
Menu for operation

Display Title Current time

Status display line for alarm
and message reception

5-1

5. OPERATION

5.1 Menu Tree

Select(1) key

(Power On)

[

▲]/[▼],[ENT]

Other Ships Lis

t

[0]-[9] or [▲]/[▼],[ENT] [0]-[9] or [▲]/[▼],[ENT] [0]-[9] or [▲]/[▼],[ENT]

[MENU]

[MENU] key

3.MAIN MENU 1.MESSAGE 1.EDIT AND TX Destination address
Message type
Message editing
Transmission

2.TX TRAY Transmitted Message reading

3.RX TRAY Received Message reading

4.INTERROGATI ON Addr ess, Req.Info., Tx and Ack

5.LONG RANGE

Received Long Range Message

2.DESTINATION 1.DESTINATION

2.WAYPOI NT TEXT

3.ETA

4. WAYPOINT

3.NAVIGATI ON 1.NAVIGATI ONAL STATUS

2.PERSONS ON-BOARD

3.TYPE OF SHIP

4.CARGO TYPE

5. DRAUGHT

6.HEIGHT OVER KEEL

4.ALARM SETTING 1.RANGE

2.LOST TARGET

5.GROUP SHIP Regi st r at i on, Delet ion

6.SET UP 1.PASSWORD Password changing

2.CH MANAGEMENT

3.OWN SHIP DATA

4.LONG RANGE RESPONSE

5. CONTRAST

6.NUMBER OF RETRIES

7.MAINTENANCE 1.TRX CONDITI ON

2.AIS ALARM

3.SENSOR STATUS

4.POWER ON/OFF LOG

5.TX ON/ OFF LOG

6.SOFTWARE VERSION

Other Ship's detail Information

5-2

5.2 Basic Operation

5.2.1 Turning the power ON

Press [PWR/DIM] for 1 second to turn ON the power, then “Other Ships List” appears.

5.2.1.1 Other Ships List

Pressing up-arrow key or down-arrow key selects the ship.
Pressing [ENT] displays the ship’s detail information.

When the selected ship’s name is longer than 11 letters, pressing right-arrow key or left-arrow key
scrolls the ship’s name to the right or to the left.

Pressing [1] switches the own ship’s information display ON/OFF.
Pressing [2] switches between the ship’s NAME display and MMSI display.
Pressing [3] switches “N”,”S”,”E”,”W” indication between left and right.

Pressing [MENU] displays “Main Menu”.

Own ship’s information

•

Latitude

•

Longitude

•

Speed Ove

r

Ground

Other ship’s information

•

Bearing

•

Range

•

Ship’s name

“∗“ Indicates group ships.

Selected ship

5-3

5.2.1.2 Other Ship’s Detail Information

Ship’s detail information can be displayed by pressing the [ENT] when the other ships list
displays.

↑ＤＥＳＴＩＮＡＴＩＯＮ：ＡＡＡＡＡＡＡＡＡＡＡＡ＞

ＰＯＳ　ＡＣＣＵＲＡＣＹ：ＨＩＧＨ
　ＰＯＳ：Ｎ：　３５°３３．３８７

'

　ＥＴＡ：１０／３１　２０：３０

↑ＰＯＳＩＴＩＯＮ（ＰＯＳ）ＳＥＮＳＯＲ：

　ＬＥＮＧＴＨ：３５ｍ

　ＤＲＡＵＧＨＴ：１０．０

m

　ＳＯＧ：　５．８ｋｎ

　ＣＯＧ：　２２．０°

ＨＤＧ：　２２．１°
↓ＲＯＴ：　０．１°／ｍｉｎ

　　ＩＮＴＥＧＲＡＴＥＤ

　　　　　Ｅ：１３９°５４．５７８

'

　ＢＲＥＡＤＴＨ：１２ｍ

　　ＴＡＮＫＥＲ

　ＳＨＩＰ　ＴＹＰＥ：

　　ＡＬＬ　ＳＨＩＰＳ　ＯＦ　ＴＨＩＳ　ＴＹＰＥ

　ＣＡＲＧＯ　ＴＹＰＥ：

Pressing [MENU] displays “Main Menu”.

Pressing this select key returns to
“Other ships list”.

Pressing this select key displays “Edit
and TX”.

Pressing down-arrow key displays next page
of the ship’s detail information.

Pressing upward arrow key displays
previous page of the ship’s detail information.

5-4

5.2.2 Turning the power OFF

Turning the power OFF needs inputting the password.
Pressing [OFF] displays “Shut-down” to input the password.

After inputting the password, pressing and holding [PWR/DIM] and [OFF] for one second turns
the power OFF.

Refer to “5.3.6.1 Password Setting” to change the password.

5-5

5.2.3 Alarm

5.2.3.1 Guard zone alarm

When other ship comes in own guard zone ring, the alarm status display “GD ZONE” appears
and alarm tone sounds.

Pressing [ALM/CLR] turns off the alarm tone.

5.2.3.2 Lost target alarm

When other ship loses in lost target ring, the alarm status display “LOST” appears and alarm tone
sounds.

Pressing [ALM/CLR] turns off the alarm tone.

The display of the alarm ship’s line is
reversal.

The display of the alarm ship’s line is
reversal.

5-6

5.3 Main Menu

“Main Menu” can display by pressing [MENU] in any operation.

ＭＡＩＮ　ＭＥＮＵ　　　　　　　　　ＵＴＣ１１：４３

６．ＳＥＴ　ＵＰ
７．ＭＡＩＮＴＥＮＡＮＣＥ

１．ＭＥＳＳＡＧＥ

３．ＮＡＶＩＧＡＴＩＯＮ

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

２．ＤＥＳＴＩＮＡＴＩＯＮ

４．ＡＬＡＲＭ　ＳＥＴＴＩＮＧ
５．ＧＲＯＵＰ　ＳＨＩＰ

○

○

○

○

Pressing up-arrow key or down-arrow key selects the menu.
Pressing [ENT] displays the selected menu display.

Pressing numerical keys [1] – [7] selects the menu and displays the selected menu display.

Pressing this select key returns “Other ships list”.

5-7

5.3.1 Message Menu

“Message Menu” can be displayed by pressing the [1] in the “Main Menu”.

(“Message Menu”)

ＭＥＳＳＡＧＥ ＭＥＮＵ ＵＴＣ１１：４３

１．ＥＤＩＴ ＡＮＤ ＴＸ

３．ＲＸ ＴＲＡＹ
４．ＩＮＴＥＲＲＯＧＡＴＩＯＮ
５．ＬＯＮＧ ＲＡＮＧＥ

２．ＴＸ ＴＲＡＹ

○

○

○

○

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

Pressing up-arrow key or down-arrow key selects the sub menu.
Pressing [ENT] displays the selected sub menu display.

Pressing numerical keys [1] – [5] selects the sub menu and displays the selected sub menu
display.

Pressing [ALM/CLR] returns to “Main Menu.

Pressing this select key returns “Other ships
list”.

5-8

5.3.1.1 Edit and TX

“Edit and TX” (MMSI, Type and Form) can be displayed by pressing the [1l in the “Message
Menu”.
The cursor appears in the “MMSI” field when “Edit and TX” display is opened.

(MMSI, Type and Form)

＠

ＥＸＩＴ＞

ＥＤＩＴ ＡＮＤ ＴＸ ＵＴＣ１１：４３

ＭＭＳＩ：０００５６９８７２ ＲＥＰＬＹ：ＯＮ
ＣＡＴＥＧＯＲＹ：ＲＯＵＴＩＮＥ ＣＨ：ＡＵＴＯ＞
ＦＩ：ＴＥＸＴ ＦＩＸＥＤ ＦＯＲＭ：０

○

○

○

○

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

(1) MMSI
Input the destination MMSI or select “BROADCAST”.
Pressing up-arrow key or down-arrow key selects between “MMSI” and “BROADCAST”.
Pressing numerical keys inputs the MMSI.
Pressing the fourth select key [(TAB)>] moves the cursor to next field (“CATEGORY”).

(2) Category
Select the message category.
Pressing up-arrow key or down-arrow key selects between “SAFETY” and “ROUTINE”. When
“ROUTINE” is selected, “FI” item appears.
Pressing the fourth select key [(TAB)>] moves the cursor to next field (“FI” or “CH” ).

(3) FI (Function Identifier)
Select the message Function Identifier.
Pressing up-arrow key or down-arrow key selects between “TEXT” and “CAPABILITY
INTEROGATE”. When “TEXT” is selected, “REPLY” item and “FIXED FORM” item appear.
Pressing the fourth select key [(TAB)>] moves the cursor to next field (“REPLY” or “CH” ).

(4) Reply
Select the message Reply between ON and OFF.
Pressing up-arrow key or down-arrow key selects between replay “ON” and replay “OFF” for
individual (not broadcast) text message.
Pressing the fourth select key [(TAB)>] moves the cursor to next field (“CH” ).

(5) Channel
Select the message transmitting channel.

Pressing up-arrow key or down-arrow key selects the transmission channel from “AUTO”, “A”, “B”

and “A/B”.

Pressing the fourth select key [(TAB)>] moves the cursor to next field (“FIXED FORM” ).

(6) Fixed Form
Select the message “Fixed Form” number.
Pressing numerical keys inputs the “Fixed Form” number.

(“0” to “9” : Fixed form , “0” : Editable message)

Pressing the fourth select key [(TAB)>] moves the cursor to next field (message editor).

Pressing this select key returns “Other ships list”.

Pressing this select key returns to previous menu.

(“Message Menu”, “TX Tray”, “RX Tray” or “Other Ship’s detail
information”)

Pressing this select key selects the setting item from
“MMSI”, “CATEGORY”, “FI”, “REPLAY”, “CH”,
“FIXED FORM”, and message editing.

5-9

(Message editor)

　　　　　　　　　 　　　　　　　　 ＥＸＩＴ＞

↑ＡＢＣＤＥＦＧＨＩＪＫＬＭ↑↓

↓．　０１２３４５６７８９＊

ＥＤＩＴ　ＡＮＤ　ＴＸ　　　　　　　ＵＴＣ１１：４３

ＭＡＹＤＡＹ！　ＭＡＹＤＡＹ！　

Ａ 　

○

○

○

○

　ＮＯＰＱＲＳＴＵＶＷＸＹＺ←→

ＴＡＢ＞

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing arrow keys move the cursor on the keypad in the display.

Pressing [ENT] input one letter from the keypad to the editing message except following cursor
position.

Pressing [ENT] at the next cursor position of “9” on the keypad close the keypad.
Pressing [ENT] at the arrow position on the keypad moves the cursor on the editing message.

Pressing [ALM/CLR] deletes one letter on the cursor in the editing message.

(Transmission Display)

ＴＸ＞

ＥＸＩＴ＞

ＥＤＩＴ ＡＮＤ ＴＸ ＵＴＣ１１：４３

ＭＡＹＤＡＹ！ ＭＡＹＤＡＹ！

ＭＭＳＩ：０００５６９８７２ ＲＥＰＬＹ：ON
ＣＡＴＥＧＯＲＹ：ＲＯＵＴＩＮＥ ＣＨ：ＡＵＴＯ ＞
ＦＩ：ＴＥＸＴ ＦＩＸＥＤ ＦＯＲＭ：０

○

○

○

○

ＡＣＫ

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

Pressing “TX” O key transmits the message.

Pressing [ALM/CLR] returns to previous menu.
(“Message Menu”, “TX Tray”, “RX Tray” or “Other Ship’s detail information”)

Pressing this select key closes the keypad and
returns to transmittable display.

Pressing this select key returns “Other ships list”.

Pressing this select key returns to previous menu.

(“Message Menu”, “TX Tray”, “RX Tray” or “Other Ship’s detail
information”)

Pressing this select key selects the setting item
from “MMSI”, “CATEGORY”, “FI”, “REPLAY”,
“CH”, “FIXED FORM”, and message editing.

Pressing this select key returns “Other ships list”.

Pressing this select key returns to previous menu.

(“Message Menu”, “TX Tray”, “RX Tray” or “Other Ship’s detail
information”)

Pressing this select key transmits the message.

A

cknowledgement status (“ACK”/”NAC”

)

5-10

5.3.1.2 TX Tray

“TX Tray”(Message List) can be displayed by pressing [2] in “Message Menu”.

(Message List)

＊ＳＡＦＥ １１１１１１１１１ ＤＥＬ＞

ＲＯＵＴ ＯＫ ＢＲＯＡＤＣＡＳＴ ＥＤＩＴ＞

ＲＯＵＴ ＮＧ ＢＲＯＡＤＣＡＳＴ

ＳＡＦＥ ＡＫ ＮＩＨＯＮＭＡＲＵ ＞ ＆ＴＸ

ＴＸ ＴＲＡＹ ＵＴＣ１１：４３

ＴＸ ＝ ２０００／０２／０２ １０：００

ＣＡＴＥＧＯＲＹ ＴＯ

○

○

○

○

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

Pressing up-arrow key or down-arrow key selects the message.
Pressing [ENT] displays “Message Read”.
Pressing [ALM/CLR] returns to “Message Menu”.

(Transmitted Message Read)

ＥＸＩＴ＞

ＥＤＩＴ＞

ＴＸ ＭＥＳＳＡＧＥ ＲＥＡＤ ＵＴＣ１１：４３

ＭＭＳＩ：０００５６９８７２ ＲＥＰＬＹ：ＮＡＫ
ＣＡＴＥＧＯＲＹ：ＲＯＵＴＩＮＥ ＣＨ：Ａ／Ｂ
ＦＩ：ＣＡＰＡＢＩＬＩＴＹ ＩＮＴＥＲＲＯＧＡＴＥ

○

○

○

○

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

Pressing [ALM/CLR] returns “TX Tray” (Message List).

Pressing this select key displays “Edit and TX”.

Pressing this select key deletes the selected
message.

Pressing this select key returns “TX Tray”
(Message List).

Message type and setting

Transmitted time of the selected message.

Pressing this select key returns “Other ships list”.

Pressing this select key displays message
editor of “Edit and TX”.

Pressing this select key returns “Other ships list”.

When “BROADCAST”, “OK”: transmission success or “NG”: transmission failure is displayed.
When “MMSI”(addressed message), ”AK”: Acknowledge received or “NK”: Acknowledge not received is displays.

5-11

(Not Transmitted Message Read)

Pressing [ALM/CLR] returns “TX Tray” (Message List).

Pressing this select key returns “TX Tray”
(Message List).

Pressing this select key transmits the message.

r

ＥＸＩＴ＞

ＴＸ＞

ＴＸ ＭＥＳＳＡＧＥ ＲＥＡＤ ＵＴＣ１１：４３

ＭＡＹＤＡＹ！ ＭＡＹＤＡＹ！

ＭＭＳＩ：０００５６９８７２ ＲＥＰＬＹ：ＡＣＫ
ＣＡＴＥＧＯＲＹ：ＲＯＵＴＩＮＥ ＣＨ：ＡＵＴＯ
ＦＩ：ＴＥＸＴ ＦＩＸＥＤ ＦＯＲＭ：０

○

○

○

○

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

5-12

5.3.1.3 RX Tray

“RX Tray”(Message List) can be displayed by pressing [3] in “Message Menu”.

(Message List)

ＲＸ　ＴＲＡＹ　　　　　　　　　　　ＵＴＣ１１：４３

＊ＲＯＵＴ　　　　７７７７７７７７７　　　ＥＤＩＴ＞

　ＳＡＦＥ　　　　ＮＩＨＯＮＭＡＲＵ

ＣＡＴＥＧＯＲＹ　ＦＲＯＭ

＊ＳＡＦＥ　ＡＫ　９９９９９９９９９　　　＆ＴＸ
　ＲＯＵＴ　　　　ＢＲＯＡＤＣＡＳＴ

ＲＸ　＝　２０００／０２／０２　１０：００

ＤＥＬ＞

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing up-arrow key and down-arrow key selects the message.
Pressing [ENT] displays “Message Read”

(Message Read)

メッセージの内容を表示する

ＭＡＹＤＡＩ！ＭＡＹＤＡＹ！

ＲＸ　ＭＥＳＳＡＧＥ　ＲＥＡＤ　　　ＵＴＣ１１：４３

ＲＸ　＝　２０００／０２／０２　１０：００

ＢＩＮ　　ＦＲＯＭ　７７７７７７７７７

ＥＸＩＴ＞

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing [ALM/CLR] returns “RX Tray” (Message List).

Pressing this select key returns “RX Tray”
(Message List).

Message type and sender of the reading
message

Received time of the selected message.

Received time of the reading message.

Pressing this select key displays “Edit and TX”.

Pressing this select key deletes the selected
message.

Pressing this select key returns “Other ships list”.

Pressing this select key returns “Other ships list”.

5-13

5.3.1.4 Interrogation

“Interrogation” can be displayed by pressing [4] in “Message Menu”.

ＩＮＴＥＲＲＯＧＡＴＩＯＮ　　　 　ＵＴＣ１１：４３

ＲＥＱ１－１：ＰＯＳＩＴＩＯＮ　ＲＥＰＯＲＴ（Ａ）
ＲＥＱ１－２：ＳＴＡＴＩＣ　＆　ＶＯＹＡＧＥ（Ａ）

２．ＤＥＳＴ２　ＭＭＳＩ：８８８８８８８８８
ＲＥＱ２－１：ＮＡＶＩＧＡＴＩＯＮ　ＴＯ　ＡＩＤＳ

３．ＩＮＴＥＲＲＯＧＡＴＥ

１．ＤＥＳＴ１　ＭＭＳＩ：７７７７７７７７

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

When “INTERRORATION” display opens, the cursor appear at the menu number “1”.

Pressing up-arrow key or down-arrow key selects the menu number.
Pressing [ENT] entries the menu number.

Pressing numerical keys [1] - [3] select and entry menu number.

Pressing [ALM/CLR] returns to “Message Menu.

(1) Inputting for No.1 destination (“DEST1”)
Pressing numerical keys inputs the MMSI of No.1 destination.
Pressing [ENT] confirms the inputted MMSI and moves the cursor to the “REQ1-1”.
Pressing the up-arrow key or down-arrow key selects No.1 request detail.
Pressing [ENT] confirms the selected detail and moves the cursor to “REQ1-2”.
Pressing the up-arrow key or down-arrow key selects No.2 request detail.
Pressing [ENT] confirms the selected detail and moves the cursor to the menu number.

(2) Inputting for No.2 destination (“DEST2”)
Pressing numerical keys inputs the MMSI of No.2 destination.
Pressing [ENT] confirms the inputted MMSI and moves the cursor to the “REQ2-1”.
Pressing the up-arrow key or down-arrow key selects request detail.
Pressing [ENT] confirms the selected detail and moves the cursor to the menu number.

(3) Interrogating
When menu number 3 “INTERROGATE” is confirmed, “INTERROGATE ACK” display appears.

Pressing this select key returns “Other ships list”.

No.1 Destination

No.2 Destination

No.1 Interrogation detail

5-14

(Interrogation and Acknowledgment)

ＩＮＴＥＲＲＯＧＡＴＥ　ＡＣＫ　　　ＵＴＣ１１：４３

１．ＡＣＫ１　ＯＫ

２．ＡＣＫ２　ＮＯＮＥ

　ＥＸＩＴ＞

ＷＡＩＴＩＮＧ

ＣＨＥＣＫ＞

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing [ALM/CLR] returns “INTERROGATION”.

(Example as Acknowledgment Detail)

Pressing this select key displays the
acknowledgment detail.

Pressing this select key returns “Other ships list”.

Pressing this select key returns
“INTERROGATION”.

Pressing this select key display No.2
acknowled

g

ment.

ＰＯＳＩＴＩＯＮ ＲＥＰＯＲＴ＿Ａ ＵＴＣ１１：４３

ＮＡＶ ＳＴＡＴＵＳ：ＵＮＤＥＲ ＷＡＹ ＵＳＩ＞
ＰＯＳＩＴＩＯＮ ＡＣＣＵＲＡＣＹ：ＨＩＧＨ

ＣＯＧ：２１６．３°

Ｎ： ３５°３３．３８７‘

ＨＥＡＤＩＮＧ：０．１°
ＲＡＴＥ ＯＦ ＴＵＲＮ：０．１°／ｍｉｎ

ＭＭＳＩ：１２３４５６７８９

Ｅ：１３９°５４．５７８‘ ＲＥＱ－２＞
ＳＯＧ：５．８ｋｎ

○

○

○

○

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

5-15

5.3.1.5 Long Range Message

“Long Range Message” can be displayed by pressing [5] in “Message Menu”.

ＬＯＮＧ　ＲＡＮＧＥ　　　　　　　ＵＴＣ１１：４３

ＦＲＯＭ　９９９９９９９９９　　　　　　　　ＡＣＫ＞
　　　　　ＯＦＦＩＣＥ

○

○

○

○

C = Position

E = Course over ground

B = Date and time of message composition

I = Destination and ETA

↓

O = Draught

F = Speed over ground

A = Ship’s name, Call sign, IMO number

P = Ship / Cargo

U = Ship's length, breadth, and type

W = Number of persons on board

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing down-arrow key displays next page of the “Long range”.
Pressing up-arrow key displays previous page of the “Long range”.

Last received message from the Long range

or

Last transmitted message to the Long range

Destination MMSI and ship’s name

Pressing this select key starts the message
transmit.

Reversal letter indicates requested item.
Right side of the not requested item is blank.

5-16

5.3.2 Destination Setting

“Destination” Setting menu can be displayed by pressing [2] in the “Main Menu”.

(“Destination” Setting menu)

ＤＥＳＴＩＮＡＴＩＯＮ ＵＴＣ１１：４３

ＴＯＫＹＯ

３．ＥＴＡ ２０１０／０２／０８ ０７：０７
（ＵＴＣ ＹＹＹＹ／ＭＭ／ＤＤ ＨＨ：ＭＭ）

ＡＢＣＤＥＦＧＨＩＪＫＬＭＮＯＰＱＲＳＴ

２．ＷＡＹＰＯＩＮＴ ＴＥＸＴ

１．ＤＥＳＴＩＮＡＴＩＯＮ

４．ＷＡＹＰＯＩＮＴ ＳＥＴ

○

○

○

○

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

Pressing up-arrow key or down-arrow key selects the sub menu.
Pressing [ENT] displays the selected sub menu display.

Pressing numerical key [1] – [4] selects the sub menu and displays the selected sub menu
display.

Pressing [ALM/CLR] returns to “Main Menu.

Pressing this select key returns “Other ships
list”.

5-17

5.3.2.1 Destination

“Destination” name can be inputted by pressing [1] in the “Destination” Setting menu.

(Selecting “Destination” name)

ＤＥＳＴＩＮＡＴＩＯＮ　　　　　　　ＵＴＣ１１：４３

ＴＯＫＹＯ

３．ＥＴＡ　　２０１０／０２／０８　０７：０７
　（ＵＴＣ　　ＹＹＹＹ／ＭＭ／ＤＤ　ＨＨ：ＭＭ）

　　　ＡＢＣＤＥＦＧＨＩＪＫＬＭＮＯＰＱＲＳＴ

２．ＷＡＹＰＯＩＮＴ　ＴＥＸＴ

１．ＤＥＳＴＩＮＡＴＩＯＮ

４．ＷＡＹＰＯＩＮＴ　ＳＥＴ

○

○

○

○

ＫＥＹＰＡＤ＞

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing [ALM/CLR] returns to the “Destination” Setting menu.
Pressing down-arrow key selects “Destination” name from inputted name log.

(Inputting “Destination” name)

　 ＮＯＰＱＲＳＴＵＶＷＸＹＺ←→　 　　ＣＬＯＳＥ

１．ＤＥＳＴＩＮＡＴＩＯＮ　　　　　　ＳＥＬＥＣＴ＞

ＤＥＳＴＩＮＡＴＩＯＮ　　　　　　　ＵＴＣ１１：４３

ＴＯＫＹＯ

２．ＷＡＹＰＯＩＮＴ　ＴＥＸＴ
　　ＡＢＣＤＥＦＧＨＩＪＫＬＭＮＯＰＱＲＳＴ

↑ ＡＢＣＤＥＦＧＨＩＪＫＬＭ↑↓　 ＨＨ：ＭＭ

↓ ．　０１２３４５６７８９＊

３．ＥＴＡ　　２０１０／０２／０８　０７：０７

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing arrow keys move the cursor on the keypad in the display.

Pressing [ENT] input one letter from the keypad to “Destination” name except following cursor
position.

Pressing [ENT] at the next cursor position of “9” on the keypad close the keypad.
Pressing [ENT] at the arrow position on the keypad moves the cursor on the “Destination”
name.

Pressing [ALM/CLR] deletes one letter on the cursor in the editing message.

Pressing this select key opens the keypad to
input “Destination” name.

Pressing this select key returns “Other ships
list”.

Pressing this select key closes the keypad to
select “Destination” name from inputted name log.

Pressing this select key returns “Other ships
list”.

Pressing this select key closes the keypad and
return to “Destination” Setting menu.

5-18

5.3.2.2 Waypoint Text

“Waypoint Text” can be inputted by pressing [2] in the “Destination” Setting menu.

　 ＮＯＰＱＲＳＴＵＶＷＸＹＺ←→　　 　ＣＬＯＳＥ

１．ＤＥＳＴＩＮＡＴＩＯＮ

ＤＥＳＴＩＮＡＴＩＯＮ　　　　　　　ＵＴＣ１１：４３

ＴＯＫＹＯ
２．ＷＡＹＰＯＩＮＴ　ＴＥＸＴ

ＡＢＣＤＥＦＧＨＩＪＫＬＭＮＯＰＱＲＳＴ

３．ＥＴＡ　　２００１／０２／０８　０７：０７
↑ ＡＢＣＤＥＦＧＨＩＪＫＬＭ↑↓　 ＨＨ：ＭＭ

↓ ．　０１２３４５６７８９＊

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

The keypad is opened, and the cursor appears in the “Waypoint Text”.

Pressing arrow keys move the cursor on the keypad in the display.

Pressing [ENT] input one letter from the keypad to “waypoint Text” except following cursor
position.

Pressing [ENT] at the next cursor position of “9” on the keypad close the keypad.
Pressing [ENT] at the arrow position on the keypad moves the cursor in the “Waypoint Text”.

Pressing [ALM/CLR] deletes one letter on the cursor in the “Waypoint Text”.

Pressing this select key closes the keypad and
return to the “Destination” Setting menu.

5-19

5.3.2.3 Estimated Time of Arrival (ETA)

Estimated Time of Arrival (ETA) can be inputted by pressing [3] in the “Destination” Setting menu.

ＤＥＳＴＩＮＡＴＩＯＮ　　　　　　　ＵＴＣ１１：４３

　　　ＴＯＫＹＯ

　　　ＡＢＣＤＥＦＧＨＩＪＫＬＭＮＯＰＱＲＳＴ

４．ＷＡＹＰＯＩＮＴＳ　ＳＥＴ

１．ＤＥＳＴＩＮＡＴＩＯＮ

３．ＥＴＡ　　２０１０／０２／０８　０７：０７
　（ＵＴＣ　　ＹＹＹＹ／ＭＭ／ＤＤ　ＨＨ：ＭＭ）

３．ＷＡＹＰＯＩＮＴ　ＴＥＸＴ

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

The cursor appears in the “ETA”.
Pressing numerical keys inputs the Estimated Time of Arrival.
Pressing right-allow key or left-allow key move the cursor in the “ETA”.
Pressing [ALM/CLR] quits the inputting and returns to the “Destination” Setting menu.
Pressing [ENT] entries the inputted data and returns to the “Destination” Setting menu.

5-20

5.3.2.4 Waypoints

“Waypoint” can be displayed by pressing [4] in the “Destination” Setting menu.
Fourteen waypoints can be set as maximum.
Twenty letters can be set as waypoint name.

Waypoint List

ＷＡＹＰＯＩＮＴＳ　　　　　　　　　ＵＴＣ１１：４３

Ｅ１３５°３０　２１０ 　　　ＤＥＬ＞
　　ＮＡＭＥ：ＥＡＳＴ　ＰＯＩＮＴ１

１．　　　Ｎ　３６°５０　１１０ 　　

ＮＡＭＥ：ＥＡＳＴ　ＰＯＩＮＴ２
　３．　　　Ｎ　３６°１０　１１０

　　　　　　Ｅ１２０°１０　１１１ＲＥＶＥＲＳＥ＞

　２．　　　Ｎ　３６°５０　１１０

　　　　　　Ｅ１３６°４０　１１０　　　　ＩＮＳ＞

↓ＮＡＭＥ：ＥＡＳＴ　ＰＯＩＮＴ３

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing up-arrow key or down-arrow key selects the waypoint.
Pressing [ALM/CLR] returns to the “Destination” Setting menu.
Pressing [ENT] confirms the selected waypoint to edit.

Editing of Waypoint
The cursor appears in the latitude field.

(1) Latitude field and longitude
Pressing up-arrow key or down-arrow key selects “N” or ”S” and “E” or “W”.
Pressing numerical keys inputs the value.
Pressing right-arrow key or left-arrow key moves the cursor.
Pressing [ALM/CLR] quits the inputting data and returns to “Waypoint List”.
Pressing [ENT] entries the inputted data and moves the cursor to next field.

(2) Waypoint name
Keypad appears in the display.
Pressing arrow keys move the cursor on the keypad in the display.
Pressing [ENT] input one letter from the keypad to the “Waypoint Name” except following cursor
position.

Pressing [ENT] at the next cursor position of “9” on the keypad close the keypad.
Pressing [ENT] at the arrow position on the keypad moves the cursor in the “Waypoint Name”.

Pressing [ALM/CLR] deletes one letter on the cursor in the “Waypoint Text”.

Pressing this select key deletes the selected
waypoint.

Pressing this select key inserts a new waypoint
before the selected waypoint to edit.

Pressing this select key switches order o

f

display in order to lower number or highe

r

number.

5-21

5.3.3 Navigation Information Setting

“Navigation Information Setting” menu can be displayed by pressing [3] in the “Main Menu”.

(“Navigation Information Setting” menu)

ＮＡＶＩＧＡＴＩＯＮ　　　　　　　　ＵＴＣ１１：４３

ＡＬＬ　ＳＨＩＰＳ　ＯＦ　ＴＨＩＳ　ＴＹＰ
５．ＤＲＡＵＧＨＴ　　　　　　　　　　　１０．０ｍ

１．ＮＡＶＩＧＡＴＩＯＡＬ　ＳＴＡＴＵＳ
　　　　ＵＮＤＥＲ　ＷＡＹ　ＵＳＩＮＧ　ＥＮＧＩＮ

６．ＨＥＩＧＨＴ　ＯＶＥＲ　ＫＥＥＬ　２０４．７ｍ

２．ＮＵＭＢＥＲ　ＯＮ－ＢＯＡＲＤ　　　　８１９１
３．ＴＹＰＥ　ＯＦ　ＳＨＩＰ
　　　　　　　　　　　ＰＡ ＳＳＥ Ｎ ＧＥＲ 　 ＳＨＩ Ｐ
４．ＣＡＲＧＯ　ＴＹＰＥ

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing up-arrow key or down-arrow key selects the sub menu.
Pressing [ENT] moves the cursor to the selected sub menu field.
Pressing numerical key [1] – [6] selects the sub menu and moves the cursor to the selected sub
menu field.
Pressing [ALM/CLR] returns to “Main Menu”.

5.3.3.1 Navigational Status Information

The cursor appears in the “Navigational Status”.
Pressing up-arrow key or down-arrow key selects the setting of “Navigational Status”.
Pressing [ALM/CLR] quits the selecting and returns to “Navigation Information Setting” menu.
Pressing [ENT] entries the selected detail and returns to “Navigation Information Setting” menu.

The setting of “Navigational Status” can be select from following detail.

0:UNDER WAY USING ENGINE
1:AT ANCHOR
2:NOT UNDER COMMAND
3:RESTRICTED MANOEUVRABILITY
4:CONSTRAINED BY HER DRAUGHT
5:MOORED
6:AGROUND
7:ENGAGED IN FISHING
8:UNDER WAY SAILING
15:NOT DEFINED

5.3.3.2 Persons On-Board

The cursor appears in the “Persons On-Board” field.
Pressing numerical key inputs the number of “Persons On-Board”.
The number can be set “8191” as maximum.
Pressing [ALM/CLR] quits the inputting and returns to “Navigation Information Setting” menu.
Pressing [ENT] entries the inputted number and returns to “Navigation Information Setting” menu.

5-22

5.3.3.3 Type of Ship and Cargo Type

The cursor appears in the “Type of Ship”/“Cargo Type”.
Pressing up-arrow key or down-arrow key selects the setting of “Type of Ship”/ “Cargo Type”.
Pressing [ALM/CLR] quits the selecting and returns to “Navigation Information Setting” menu.
Pressing [ENT] entries the selected detail and returns to “Navigation Information Setting” menu.

The setting of “Type of Ship ” can be select from following detail.

2x:WIG
30:FISHING VESSEL
31:TOWING VESSEL
32:TOWING VESSEL-L>200M B>25M

(Towing and length of the tow exceeds 200m or breadth exceeds 25m)
33:DREDGE OR UNDERWATER OPE (Engaged in dredging or underwater operation)
34:VESSEL-DIVING OPE (Engaged in diving operation)
35:VESSEL-MILITARY OPE (Engaged in military operation)
36:SAILING VESSEL
37:PLEASURE CRAFT
4x:HSC (High Speed Craft)
50:PILOT VESSEL
51:SERCH AND RESCUE VESSELS
52:TUGS
53:PORT TENDERS
54:WITH ANTI-POLLUTION EQUIP (Vessels with anti-pollution facilities or equipent)
55:LAW ENFORCEMENT VESSELS
58:MEDICAL TRANSPORTS
59:RESOLUTION NO18:MOB-83 (Ships according to Resolution No 18 (Mob-83))
6x:PASSENGER SHIP
7x:CARGO SHIPS
8x:TANKER
9x:OTHER TYPE OF SHIP

The setting of “Cargo Type” can be select from following detail except when the “Type of Ship ”
sets the above “30-37” and “50-59”.

x0:ALL SHIP OF THIS TYPE
x1:CATEGORY A (DG/HP/MP)

(Carrying Dangerous Goods, Harmful Substances, or Marine Pollutants. IMO hazard or

pollutant category A)
x2:CATEGORY B (DG/HP/MP)

(Carrying Dangerous Goods, Harmful Substances, or Marine Pollutants. IMO hazard or

pollutant category B)
x3:CATEGORY C (DG/HP/MP)

(Carrying Dangerous Goods, Harmful Substances, or Marine Pollutants. IMO hazard or

pollutant category C)
x4:CATEGORY D (DG/HP/MP)

(Carrying Dangerous Goods, Harmful Substances, or Marine Pollutants. IMO hazard or

pollutant category D)
x9:NO ADDTIONAL INFORMATION

Additionally, the setting of “Cargo Type” can be select from following detail except when the “Type
of Ship ” sets the above “2x”, “30-37”, “4x” and “50-59”.

x5:NOT UNDER COMMAND
x6:RESTRICTED BY (her ability) MANOEUVRE
x7:CONSTRAINED BY (her) DRAUGHT

5-23

5.3.3.4 Draught

The cursor appears in the “Draught”.
Pressing numerical key inputs the value of “Draught”.
The value can be set “25.5m” as maximum.
Pressing [ALM/CLR] quits the inputting and returns to “Navigation Information Setting” menu.
Pressing [ENT] entries the inputted value and returns to “Navigation Information Setting” menu.

5.3.3.5 Height Over Keel

The cursor appears in the “Height Over Keel”.
Pressing numerical key inputs the value of “Height Over Keel”.
Pressing [ALM/CLR] quits the inputting and returns to “Navigation Information Setting” menu.
Pressing [ENT] entries the inputted value and returns to “Navigation Information Setting” menu.

5-24

5.3.4 Alarm Setting

“Alarm Setting” menu can be displayed by pressing [4] in the “Main Menu”.

(“Alarm Setting” menu)

ＡＬＡＲＭ ＳＥＴＴＩＮＧ ＵＴＣ１１：４３

１．ＲＡＮＧＥ １０．０ＮＭ ＞

２．ＬＯＳＴ ＴＡＲＧＥＴ １０．０ＮＭ ＞

○

○

○

○

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

Pressing up-arrow key or down-arrow key selects the sub menu.
Pressing [ENT] moves the cursor to the selected sub menu field.
Pressing numerical key [1] – [2] selects the sub menu and moves the cursor to the selected sub
menu field.
Pressing [ALM/CLR] returns to “Main Menu.

5.3.4.1 Range

The cursor appears in the “Range” field.
Pressing numerical key inputs the value of “Range” for Guard Zone alarm.
The value can be set “99.9 nautical mile” as maximum.
Pressing [ALM/CLR] quits the inputting and returns to “Alarm Setting” menu.
Pressing [ENT] entries the inputted value and returns to “Alarm Setting” menu.

5.3.4.2 Lost Target

The cursor appears in the “Lost Target” field.
Pressing numerical key inputs the value of “Lost Target” for Lost Target alarm.
The value can be set “99.9 nautical mile” as maximum.
Pressing [ALM/CLR] quits the inputting and returns to “Alarm Setting” menu.
Pressing [ENT] entries the inputted value and returns to “Alarm Setting” menu.

Pressing this select key moves the cursor to the
“Range” field for Guard Zone alarm.

Pressing this select key moves the cursor in the
“Lost Target” field for Lost Target alarm.

5-25

5.3.5 Group Ship Setting

“Group Ship List” can be displayed by pressing [5] in the “Main Menu”.
Ten MMSI can be registered for own group as maximum.

(“Group Ship List”)

ＧＲＯＵＰ　ＳＨＩＰ　ＬＩＳＴ　　　ＵＴＣ１１：４３

　ＮＡＭＥ　　　　　　　ＭＭＳＩ

　ＮＩＨＯＮＭＡＲＵ２　４３１０００００２

　ＮＩＨＯＮＭＡＲＵ３　４３１０００００３

　ＮＩＨＯＮＭＡＲＵ５　４３１０００００５

　ＳＹＯＷＡＮＩＨＯ＞　４３１０００００４

ＤＥＬ　ＡＬＬ＞

　ＮＩＨＯＮＭＡＲＵ１　４３１０００００１

○

○

○

○

ＩＮＳ＞

ＤＥＬ＞

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing up-arrow key or down-arrow key selects ship.
Pressing [ENT] confirms the selected ship to edit the registry.

5.3.5.1 Ship Name

ＧＲＯＵＰ ＳＨＩＰ ＬＩＳＴ ＵＴＣ１１：４３

ＮＡＭＥ ＭＭＳＩ

ＮＩＨＯＮＭＡＲＵ２ ４３１０００００２

ＮＩＨＯＮＭＡＲＵ３ ４３１０００００３

ＳＹＯＷＡＮＩＨＯ＞ ４３１０００００４

ＳＨＩＰＮＡＭＥ ＥＤＩＴ

Ｂ

↑ＡＢＣＤＥＦＧＨＩＪＫＬＭ↑↓
ＮＯＰＱＲＳＴＵＶＷＸＹＺ←→
↓． ０１２３４５６７８９＊

ＥＸＩＴ＞

○

○

○

○

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

The cursor appears in the “Ship Name” field and keypad appears in the display.
Pressing arrow keys move the cursor on the keypad in the display.
Pressing [ENT] input one letter from the keypad to the “Ship Name” except following cursor
position.

Pressing [ENT] at the next cursor position of “9” on the keypad closes the keypad.
Pressing [ENT] at the arrow position on the keypad moves the cursor in the “Ship Name”.

Pressing [ALM/CLR] deletes one letter on the cursor in the “Ship Name”.

5.3.5.2 MMSI

The cursor appears in the “MMSI” field.
Pressing numerical key inputs the number of “MMSI”.
Pressing [ALM/CLR] quits the inputting and returns to “Group Ship List”.
Pressing [ENT] entries the inputted number and returns to “Group Ship List”.

Pressing this select key inserts a new ship‘s
registry before the selected ship.

Pressing this select key deletes all registries as
group.

Pressing this select key deletes the selected
ship‘s registry.

Pressing this select key closes the keypad and
moves the cursor to the “MMSI” field.

5-26

5.3.6 Setup menu

“Setup” menu can be displayed by pressing [6] in the “Main Menu”.

(“Set up” menu)

ＳＥＴＵＰ　　　　　　　　　　　　　ＵＴＣ１１：４３

５．ＣＯＮＴＲＡＳＴ

２．ＣＨ　ＭＡＮＡＧＥＭＥＮＴ

１．ＰＡＳＳＷＯＲＤ

４．ＭＥＳＳＡＧＥ　ＲＥＳＰＯＮＳＥ

２．ＯＷＮ　ＳＨＩＰ　ＤＡＴＡ

６．ＮＵＭＢＥＲ　ＯＦ　ＲＥＴＲＩＥＳ：　　　　３

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing up-arrow key or down-arrow key selects the sub menu.
Pressing [ENT] opens the selected sub menu display.
Pressing numerical key [1] – [6] selects the sub menu and opens the selected sub menu display.
Pressing [ALM/CLR] returns to “Main Menu.

5-27

5.3.6.1 Password Setting

“Password” setting menu can be displayed by pressing [1] in the “Setup” menu.

(“Password” setting menu)

ＰＡＳＳＷＯＲＤ ＵＴＣ１１：４３

ＮＥＷ：＊＊＊＊

ＯＬＤ：＊＊＊＊

ＮＥＷ：＊＊＊＊

２．ＰＡＳＳＷＯＲＤ ＳＥＴ／ＣＨＡＮＧＥ

１．ＰＡＳＳＷＯＲＤ ＊＊＊＊

○

○

○

○

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

Pressing up-arrow key or down-arrow key selects the sub menu.
Pressing [ENT] moves the cursor to the selected sub menu field.
Pressing numerical key [1] – [2] selects the sub menu and moves the cursor to the selected sub
menu field.
Pressing [ALM/CLR] returns to “Setup” menu.

(1) “Password” conforming

The cursor appears in the “Password”.
Pressing numerical key inputs the password.
Pressing [ALM/CLR] quits the inputting and returns to the “Password” setting menu.
Pressing [ENT] conforms the inputted password and displays “OK” or “NG” as the result.

(2) “Password Set/Change”

The cursor appears in the “Password Set/Change”.
Pressing numerical key inputs the password.
Pressing [ALM/CLR] quits the inputting and returns to the “Password” setting menu.
Pressing [ENT] entries the inputted password and moves the cursor to the next field.

5-28

5.3.6.2 Channel Management Setting

“Channel Management” setting menu can be displayed by pressing [2] in the “Set Up” menu.
Eight channel management settings can be memorized in the transponder as maximum.

(“Channel Management” setting menu)

ＣＨ　ＭＡＮＡＧＥＭＥＮＴ　　　　　ＵＴＣ１１：４３

２．ＣＨ　Ｂ：２０８８　ＮＡＲＲＯＷ　　　　ＲＸ
３．ＴＸ　ＰＯＷＥＲ　：ＨＩＧＨ

６．ＡＲＥＡ　Ｎ　３５°３３．３８７０‘

４．ＺＯＮＥ　ＳＩＺＥ：５ｎｍ

　　（ＳＷ）　Ｅ１３９°５４．５７８０‘　ＬＩＳＴ＞

１．ＣＨ　Ａ：２０８７　ＷＩＤＥ　　　ＴＸ／ＲＸ

５．ＡＲＥＡ　Ｎ　３５°３３．３８７０‘ＣＨＥＣＫ＞
　　（ＮＥ）　Ｅ１３９°５４．５７８０‘

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing up-arrow key or down-arrow key selects the sub menu.
Pressing [ENT] moves the cursor to the selected sub menu field.
Pressing numerical key [1] – [6] selects the sub menu and moves the cursor to the selected sub
menu field.
Pressing [ALM/CLR] returns to “Set Up” menu.

(1) Inputting of the Channel Management

“CH A”
The cursor appears in the “CH A” field.
Pressing numerical keys inputs the channel A number.
Pressing up-arrow key or down-arrow key selects the detail.

(“WIDE” or ”NALLOW”, “TX/RX” or “RX”)

Pressing [ALM/CLR] quits the inputting and returns to the “Channel Management” setting menu.
Pressing [ENT] entries the inputted number or detail and moves the cursor to the next field.

“CH B”
The cursor appears in the “CH B” field.
Pressing numerical keys inputs the channel B number.
Pressing up-arrow key or down-arrow key selects the detail.

(“WIDE” or ”NALLOW”, “TX/RX” or “RX”)

Pressing [ALM/CLR] quits the inputting and returns to the “Channel Management” setting menu.
Pressing [ENT] entries the inputted number or detail and moves the cursor to the next field.

Pressing this select key checks whether or not
the inputted detail can be set to the
transponder.

Pressing this select key displays the channel
management setting of the transponder.

5-29

“TX Power”
The cursor appears in the “TX Power” field.
Pressing up-arrow key or down-arrow key inputs the “TX power” detail from “High” or “Low”
Pressing [ALM/CLR] quits the inputting and returns to the “Channel Management” setting menu.
Pressing [ENT] entries the inputted detail and returns to the “Channel Management” setting
menu.

“Zone Size”
The cursor appears in the “Zone Size” field.
Pressing numerical keys inputs value of the “Zone Size” .
The value can be input “1” as minimum and “8” as maximum.
Pressing [ALM/CLR] quits the inputting and returns to the “Channel Management” setting menu.
Pressing [ENT] entries the inputted value and moves the cursor to the next field.

“Northeast” corner and “Southwest” corner of the Area
The cursor appears in the “Area(NE)”/“Area(SW)”.
Pressing up-arrow key or down-arrow key inputs “N” or ”S” and “E” or “W”.
Pressing numerical keys inputs the value of the latitude / longitude.
Pressing [ALM/CLR] quits the inputting and returns to the “Channel Management” setting menu.
Pressing [ENT] entries the inputted value and moves the cursor to the next field.

5-30

(2) Check and Set the Channel Management

The inputted Channel Management detail has to be registered to the transponder for channel
management operation.
Pressing the “[Check]” select key checks whether or not the inputted detail can be set to the
transponder, and display “OK” or “NG” as the result.
When the check result was “OK”, then select key function “[Set]” is appears on the “[List] ”
position.

(Checked Channel Management detail : “OK”)

ＣＨ　ＭＡＮＡＧＥＭＥＮＴ　　　　　ＵＴＣ１１：４３

２．ＣＨ　Ｂ：２０８８　ＮＡＲＲＯＷ　　　　ＲＸ
３．ＴＸ　ＰＯＷＥＲ　：ＨＩＧＨ

６．ＡＲＥＡ　Ｎ　３５°３３．３８７０‘

４．ＺＯＮＥ　ＳＩＺＥ：５ｎｍ

　　（ＳＷ）　Ｅ１３９°５４．５７８０‘　　ＳＥＴ＞

１．ＣＨ　Ａ：２０８７　ＷＩＤＥ　　　ＴＸ／ＲＸ

５．ＡＲＥＡ　Ｎ　３５°３３．３８７０‘ＣＨＥＣＫ＞
　　（ＮＥ）　Ｅ１３９°５４．５７８０‘ＯＫ

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

(Checked Channel Management detail : “NG”)

ＣＨ　ＭＡＮＡＧＥＭＥＮＴ　　　　　ＵＴＣ１１：４３

２．ＣＨ　Ｂ：２０８８　ＮＡＲＲＯＷ　　　　ＲＸ
３．ＴＸ　ＰＯＷＥＲ　：ＨＩＧＨ

６．ＡＲＥＡ　Ｎ　３５°３３．３８７０‘

４．ＺＯＮＥ　ＳＩＺＥ：５ｎｍ

　　（ＳＷ）　Ｅ１３９°５４．５７８０‘　　ＳＥＴ＞

１．ＣＨ　Ａ：２０８７　ＷＩＤＥ　　　ＴＸ／ＲＸ

５．ＡＲＥＡ　Ｎ　３５°３３．３８７０‘ＣＨＥＣＫ＞
　　（ＮＥ）　Ｅ１３９°５４．５７８０‘ＮＧ

ＮＧ：ＡＲＥＡ　ＣＯＮＲＮＥＲ　ＥＲ　　ＮＧ

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing this select key checks whether o

r

not the inputted detail can be registered to the
transponder.

Pressing this select key registers the inputted
channel management detail to the transponder.

Pressing this select key checks whether o

r

not the inputted detail can be registered to the
transponder.

Pressing this select key registers the inputted
channel management detail to the transponder.

Reason about check result “NG”

Check result “OK”

5-31

(3) Channel Management list

Display and Confirm the registered Channel Management detail list from the transponder to input
manually the channel management detail.
Pressing the “[List]” select key displays the channel management setting of the transponder.

(Channel Management List)

Pressing down-arrow key displays next page of the “Channel Management List”.
Pressing up-arrow key displays previous page of the “Channel Management List”.
Pressing [ALM/CLR] closes the “Cannel Management List” and returns to the “Channel
Management” setting menu.

ＣＨ　ＭＡＮＡＧＥ　ＬＩＳＴ　　　　ＵＴＣ１１：４３

ＣＨ　Ｂ：２０８８　ＮＡＲＲＯＷ　　　　　ＲＸ
　　ＴＸ　ＰＯＷＥＲ　：ＨＩＧＨ

　　ＡＲＥＡ　Ｎ　３５°３３．３８７　　　 ＥＸＩＴ＞

　　ＺＯＮＥ　ＳＩＺＥ：５ｎｍ

↓　（ＳＷ）　Ｅ１３９°５４．５７８

１．ＣＨ　Ａ：２０８７　ＤＥＦＡＵＬＴ　ＴＸ／ＲＸ

ＡＲＥＡ　Ｎ　３５°３３．３８７
　　（ＮＥ）　Ｅ１３９°５４．５７８

ＣＨ　Ｂ：２０８８　ＮＡＲＲＯＷ　　　　　ＲＸ
　　ＴＸ　ＰＯＷＥＲ　：ＨＩＧＨ
　　ＺＯＮＥ　ＳＩＺＥ：５ｎｍ

↓　（ＳＷ）　Ｅ：１３９°５４．５７８‘

２．ＣＨ　Ａ：２０８７　ＤＥＦＡＵＬＴ　ＴＸ／ＲＸ

ＡＲＥＡ　Ｎ：　３５°３３．３８７‘
　　（ＮＥ）　Ｅ：１３９°５４．５７８‘

↑

　　ＡＲＥＡ　Ｎ：　３５°３３．３８７‘　ＥＸＩＴ＞

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing this select key closes the “Cannel
Management List” and returns to the “Channel
Management” setting menu.

Pressing this select key closes the “Cannel
Management List” and returns to the “Channel
Management” setting menu.

5-32

5.3.6.3 Own Ship Data display setting

“Own Ship Data” display setting menu can be displayed by pressing [3] in the “Set Up” menu.

(“Own Ship Data” display setting menu)

ＯＷＮ　ＳＨＩＰ　ＤＡＴＡ　ＯＮ　　ＣＨＡＮＧＥ＞

ＯＷＮ　ＳＨＩＰ　ＤＡＴＡ　　　　　ＵＴＣ１１：４３

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing [ALM/CLR] returns to “Set Up” menu.

5.3.6.4 Long Range Response setting

“Long Range Response” setting menu can be displayed by pressing [4] in the “Set Up” menu.

(“Long Range Response” setting menu)

ＬＲ　ＲＥＳＰＯＮＳＥ　　　　　　　ＵＴＣ１１：４３

ＬＯＮＧ　ＲＡＮＧＥ　ＲＥＳＰＯＮＳＥ

ＡＵＴＯＭＡＴＩＣ

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing up-arrow key or down arrow-key switches the setting of “Long Range Response”
between “Automatic” and “Manual”.

Pressing [ALM/CLR] returns to “Set Up” menu.

Pressing this select key switches the setting of
“Own Ship Data” display between “ON” /
“OFF”.

5-33

5.3.6.5 Contrast setting

“Contrast” setting menu can be displayed by pressing [5] in the “Set Up” menu.

(“Contrast” setting menu)

ＣＯＮＴＲＡＳＴ ＵＴＣ１１：４３

ＣＯＮＴＲＡＳＴ： ４

○

○

○

○

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

Pressing up-arrow key or down arrow-key selects and sets “Contrast” Setting from “0” – “64”.

Pressing [ALM/CLR] returns to “Set Up” menu.

5.3.6.6 Number of Retries Setting

The cursor moves to the “Number of Retries” setting field by pressing [6] in the “Set Up” menu.

(“Number of Retries” setting)

ＳＥＴＵＰ　　　　　　　　　　　　　ＵＴＣ１１：４３

５．ＣＯＮＴＲＡＳＴ

２．ＣＨ　ＭＡＮＡＧＥＭＥＮＴ

１．ＰＡＳＳＷＯＲＤ

４．ＭＥＳＳＡＧＥ　ＲＥＳＰＯＮＳＥ

２．ＯＷＮ　ＳＨＩＰ　ＤＡＴＡ

６．ＮＵＭＢＥＲ　ＯＦ　ＲＥＴＲＩＥＳ：　　　　

３

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

The cursor appears in the “Number of Retries”.
Pressing numerical key inputs the “Number of Retries”.
The number can be set “3” as maximum.
Pressing [ALM/CLR] quits the inputting and returns to “Set Up” menu.
Pressing [ENT] entries the inputted number and returns to “Set Up” menu.

5-34

5.3.7 Maintenance menu

“Maintenance” menu can be displayed by pressing [7] in the “Main Menu”.

(“Maintenance” menu)

ＭＡＩＮＴＥＮＡＮＣＥ ＵＴＣ１１：４３

３．ＳＥＮＳＯＲ ＳＴＡＴＵＳ

５．ＰＡＳＳＷＯＲＤ ＬＯＧ

２．ＡＩＳ ＡＬＡＲＭ

１．ＴＲＸ ＣＯＮＤＩＴＩＯＮ

４．ＰＯＷＥＲ ＯＮ／ＯＦＦ ＬＯＧ

６．ＳＯＦＴＷＡＲＥ ＶＥＲＳＩＯＮ

○

○

○

○

ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１

Pressing up-arrow key or down-arrow key selects the sub menu.
Pressing [ENT] opens the selected sub menu display.
Pressing numerical key [1] – [6] selects the sub menu and opens the selected sub menu display.
Pressing [ALM/CLR] returns to “Main Menu.

5-35

5.3.7.1 TRX Condition log display

“TRX Condition” log display can be displayed by pressing [1] in the “Maintenance” menu.
Latest condition is displayed as “1” (Operating condition).

(“TRX Condition” log display)

Pressing up-arrow key or down-arrow key scrolls the display.
Pressing [ALM/CLR] returns to “Mailtenance” menu.

“Channel A and B” number

“TX Power” (“HIGH” / ”LOW”)

“Northeast Corner of the Area”

“Southwest Corner of the Area”.

TRX mode (“TX/RX” / “RX”)

(When channel management operation)

ＴＲＸ　ＣＯＮＤＩＴＩＯＮ　　　　　ＵＴＣ１１：４３

ＣＨ　Ｂ：２０８８　ＮＡＲＲＯＷ　　　　　ＲＸ
　　ＴＸ　ＰＯＷＥＲ　：ＨＩＧＨ

　　ＡＲＥＡ　Ｎ：　３５°３３．３８７‘

　　ＺＯＮＥ　ＳＩＺＥ：５ｎｍ

↓　（ＳＷ）　Ｅ：１３９°５４．５７８‘

１．ＣＨ　Ａ：２０８７　ＤＥＦＡＵＬＴ　ＴＸ／ＲＸ

ＡＲＥＡ　Ｎ：　３５°３３．３８７‘
　　（ＮＥ）　Ｅ：１３９°５４．５７８‘

ＣＨ　Ｂ：２０８８　ＮＡＲＲＯＷ　　　　　ＲＸ
　　ＴＸ　ＰＯＷＥＲ　：ＨＩＧＨ

　　ＡＲＥＡ　Ｎ：　３５°３３．３８７‘

　　ＺＯＮＥ　ＳＩＺＥ：５ｎｍ

↓　（ＳＷ）　Ｅ：１３９°５４．５７８‘

２．ＣＨ　Ａ：２０８７　ＤＥＦＡＵＬＴ　ＴＸ／ＲＸ

ＡＲＥＡ　Ｎ：　３５°３３．３８７‘
　　（ＮＥ）　Ｅ：１３９°５４．５７８‘

↑

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Bandwidth (“Wide“ / “Narrow”)

“Zone Size”

5-36

5.3.7.2 AIS Alarm display

“AIS Alarm” display can be displayed by pressing [2] in the “Maintenance” menu.
Latest alarm status is displayed.

(“AIS Alarm ” display)

Pressing up-arrow key or down-arrow key scrolls the display.
Pressing [ALM/CLR] returns to “Maintenance” menu.

5.3.7.3 Sensor Status display

“Sensor Status” display can be displayed by pressing [3] in the “Maintenance” menu.
Latest sensor status is displayed.

(“Sensor Status ” display)

ＳＥＮＳＯＲ　ＳＴＡＴＵＳ　　　　　ＵＴＣ１１：４３

４．ＨＥＡＤＩＮＧ　　：ＶＡＬＩＤ

３．ＳＯＧ／ＣＯＧ　　：ＥＸＴＥＲＮＡＬ

１．ＰＯＳＩＴＩＯＮ　：ＩＮＴＥＲＮＡＬ

２．ＵＴＣ　ＣＬＯＣＫ：ＬＯＳＴ

５．ＲＯＴ　　　　　　：ＯＨＴＥＲ　ＳＥＮＳＯＲ

　　　　　　　　　　　　ＤＧＮＳＳ（ＭＳＧ．１７）

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing [ALM/CLR] returns to “Maintenance” menu.

ＡＩＳ　ＡＬＡＲＭ　　　　　　　　　ＵＴＣ１１：４３

Ａ　２００１／１１／０９　１０：２０
　０５９：Ｄｕｃ　ｅｒｒｏｒ
　Ａ　２００１／１１／０９　１０：２０
　０５９：Ｔｘ　ｍａｌｕｆｕｎｃｉｏｎ

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

5-37

5.3.7.4 Power On/Off Log display

“Power On/Off Log” display can be displayed by pressing [4] in the “Maintenance” menu.

(“Power On/Off Log” display)

ＰＯＷＥＲ　ＯＮ／ＯＦＦ　ＬＯＧ　　ＵＴＣ１１：４３

ＯＦＦ　２０１０／０２／０２　０９：００：５９
　ＯＮ　　２０１０／０２／０２　０８：００：５９
　ＯＦＦ　２０１０／０２／０２　０７：００：５９

　ＯＮ　　２０１０／０２／０２　１０：００：５９

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

Pressing up-arrow key or down-arrow key scrolls the display.
Pressing [ALM/CLR] returns to “Maintenance” menu.

5.3.7.5 Password Log

“Password Log” display can be displayed by pressing [5] in the “Maintenance” menu.
This display not used.

5.3.7.6 Software Version display

“Software Version” display can be displayed by pressing [6] in the “Maintenance” menu.

(“Software Version” display)

Pressing [ALM/CLR] returns to “Maintenance” menu.

ＳＯＦＴＷＡＲＥ　ＶＥＲＳＩＯＮ　　ＵＴＣ１１：４３

ＣＯＮＴＲＯＬＬＥＲ　：１．００

ＴＲＡＮＳＰＯＮＤＥＲ：１．００

○

○

○

○

ＢＲＧ　：　ＲＡＮＧＥ　　　ＮＡＭＥ／ＭＭＳＩ
　２７０°：　０．１８ＮＭ　ＪＲＣ　ＭＡＲＵ１
　　３５°：　０．２９ＮＭ　ＪＲＣ　ＭＡＲＵ２
　　２２°：　０．９２ＮＭ　ＪＲＣ　ＭＡＲＵ１

6-1

6. MAINTENANCE AND INSPECTION

The performance and longevity of this equipment depend on careful maintenance. To maintain
the best performance, the following periodic inspections are highly recommended.

(1) Keep the power supply voltage within the specified value.
(2) Know the condition of normal status when the equipment is properly functioning. Keep

comparing the current status to the normal status to immediately detect any malfunctions.

With the exception of qualified service personnel, do not attempt to service the
interior of this equipment, as doing so may cause fire, electric shock or malfunction.

Each internal circuit has been fine-tuned, therefore be sure not to tune or modify
without measuring instruments. If any malfunctions are detected, contact our
service center or agents.

6. 1 General Maintenance and Inspection

Below are listed general maintaining and inspecting items which can be done with usual tools and
apparatus.

No. Item Maintenance and inspection

1 Cleaning

Gently clean the surface of the panel, knobs, switches, and upper/bottom
cover with a soft cloth or silicon oil.
Remove dust in the unit using a brush or vacuum cleaner. No oil is needed
because this unit has no moving mechanisms inside.

2

Looseness

of parts

Inspect for looseness and correctly tighten the following:
screws, nuts, knobs, switches, volume pots, connectors and relays inserted
into sockets.

3 Fuse

If the power source fuse is blown, be sure to inspect the cause before
replacing the blown fuse with a new one.

4 PCB Unit

Remove screws mounting the unit, demount the unit from the main chassis,
and inspect the unit for discoloration and parching of components. To
exchange parts, call our service center or agents.

6. 2 Maintenance Menu

About self-diagnostics and monitoring system status, please refer to “5.3.7 Maintenance Menu”

WARNING

If you remove the PCB unit, be sure to store it in a non-conductive bag.
If you wrap it up with materials such as aluminum, the buck-up power supply may
short

Note

7-1

7. AFTER-SALES SERVICE

Before returning repair

If what appears to be a defect is detected, refer to “6.3 Troubleshooting” to check if the equipment is
actually defective before requesting repair.
If the defect persists, immediately stop operation and call our service center or agents.

 During the warranty period, we or our agencies (*1) will repair the malfunction without any fee,

according to the specified procedure.

 After the warranty expires, we will repair the malfunction for a fee, if repair is possible.
 Item for notification

Product name, type, manufactured data, serial number,
information about the malfunction (the more detailed, the better),
your company or organization name, address and phone number.

Periodical maintenance recommended

Performance of this equipment may degrade over time because parts wear out, although degradation
depends on how this unit has been maintained.
We recommend periodic professional maintenance checks in addition to daily maintenance.
Call our service center or agents for periodic professional maintenance (This maintenance requires a
service charge).

Call our office or the nearest agency for detailed information about after-sales service.

(*1) Refer to the inside of the back cover for contact numbers.

8-1

8. SPECIFICATIONS

8.1 AIS TRANSPONDER (NTE-180)

(1) Frequency range : 156.025MHz to 162.025MHz,

: Default channels:161.975MHz, 162.025MHz

(2) Channel spacing : 25kHz/12.5kHz

(3) Frequency accuracy : Within ±3×10

-6

(4) Type of emission : F1D, F2B
(5) Type of modulation : GMSK, FSK
(6) Output power : 12.5W/2W
(7) Rated power supply voltage : 24Vdc (-10%, +30%)
(8) Current consumption : 4.5A max: when transmitting

: 1.5A max: when receiving

(9) Operating temperature : -25°C to +55°C (IEC 60945)

8.2 AIS CONTROLLER (NCM-722)

8.2.1 Operation panel

(1) Type of display : 5-inch STN LCD, 160×128 dots
(2) Keyboard : 23 keys
(3) Back-light : For LCD and keyboard
(4) Dimmer control : Bright, medium1, medium2, off (Selectable from keyboard)

8.2.2 Environmental condition

(1) Operating temperature : -15°C to +55°C (IEC 60945)
(2) Power voltage : 24Vdc -10% to +30% (IEC 60945)

8.2.3 External interfaces

(1) Sensor data input ports SENSOR1 / SENSOR2/ SENSOR3

Three input ports meet the requirements of IEC 61162-2.
Additionally, these ports can receive data from IEC61162-1 sensor with one-to-one connection.

(2) Sensor data input ports SENSOR4/ SENSOR5

Two input ports using photo-coupler
These ports can receive data from IEC61162-1 sensor and half signal drive sensor such as
photo-coupler driver.

(3) NSK for Gyro communication port

One communication port for current loop

(4) External display equipment communication ports

Two communication ports meet the requirements of IEC 61162-2

(5) Long range communication port

One communication port meets the requirements of IEC 61162-2

(6) GNSS differential correction data communication port

One communication port meets the requirement of ITU-R M.823-2

(7) Relay terminals

Two ports for external alarm device

8-2

Note: IEC61162-2 interfaces comply with the following specifications.

- Output drive capacity: Differential driver output voltage is 2.0V or more (RL=100 ohms), Driver
output current 50mA

- Load on the line of inputs: 100 ohms. 1 IEC61162-1 output can drive 1 IEC61162-2 input.

- Electrical isolation of input circuits: Input circuits are electrically isolated from internal circuit with
opto-isolator.

8.2.4 Supported interface sentences

Indication Sentence format Supported sentence formatters

Input data Recommend Optional
Longitude/Latitude
Position Accuracy
Time of Position

GNS
GLL

GGA
RMC

Datum Reference DTM
RAIM Indicator GBS
Speed Over Ground
(SOG)

VBW VTG

OSD

RMC
Course Over Ground
(COG)

RMC VTG

OSD
Heading HDT OSD

1.

SENSOR1
SENSOR2
SENSOR3
SENSOR4
SENSOR5

IEC61162-1/2

Rate of Turn (*1) ROT

2.

NSK

IEC61162-1 Input: VHW

3.

AUX1
AUX2

IEC61162-2
IEC61993-2

Input: ABM, ACA, ACK, AIR, BBM, LRI, LRF, VSD,
SSD
Output: ABK, ACA, ALR, DSC, DSI, LRF, LR1, LR2,
LR3, TXT, VDO, VDM

4.

LONGRANGE

IEC61993-2 Input: LRI, LRF

Output: LRF, LR1, LR2, LR3

5.

DIFF

ITU-R M.823-2 Input: RTCM SC-104 Ver.2.0 Type 1, 2, 7, 9

Output: RTCM SC-104 Ver. 2.0 Type: depends on
received message

6.

MAINTE

Prepared for future use

7.

NMEA2000

(Optional)

IEC61162-3 Prepared for future use

(*1) Rate of Turn includes errors caused by calculation in the range of +/- 5.6 degree/minute.

8.3 POWER SUPPLY UNIT (NBD-577A)

(1) Input voltage :100 or 220 Vac ±10% 50/60Hz Single phase

:24Vdc (Back up power supply)

(2) Output voltage :24Vdc

For further information contact:

HEAD OFFICE &
SALES DEPT.

Akasaka Twin Tower (Main),
17-22, Akasaka 2-chome, Minato-ku,
Tokyo 107-8432 JAPAN
Phone : [phone]
Fax : [phone]
Telex : 0242-5420 JRCTOK J

MAIN PLANT

1- 1, Shimorenjaku 5-chome, Mitaka-shi,
Tokyo 181-8510 JAPAN
Phone : [phone]
Fax : [phone]
Telex : 02822-351 JRCMTK J