
John Deere 8400 Diagnostic Codes
When either a Service Alert or Information
indicator is displayed it is suggested the tractor
be placed in park or engine shut off. Restart
the engine to verify if the active Diagnostic
Trouble Code reappears before contacting
your John Deere dealer. Sometimes, the code
can be corrected by resetting the
communication messages when tractor is
restarted.
Some Service Alerts and Information
indicators can be acknowledged and display
cleared by pressing the select switch on the
CommandCenter. The display will return to a
normal mode allowing tractor function to
continue. However, diagnostic trouble code
may reappear at a later date if condition still
exists. For an explanation of STOP, Service
Alert, Information Indicators and Diagnostics
Trouble Codes refer to section 15 in this
document.
OU1092A,0000020 -19-28SEP06-1/27
Solution
Armrest Control Unit Diagnostic Trouble Codes (ACU)
ACU Switched Supply Voltage Low. Visually inspect
around the batteries and alternator for any visual signs of
damage or accumulated debris. Have John Deere dealer
repair as soon as possible.
Transmission Oil
Temperature Low
Engine Speed Limited Due to Cold Oil. Slow engine speed
to less than 1500 rpm until hydraulic oil temp is above -5
°C (23 °F).
Transmission Not Responding to Command. Have John
Deere dealer repair as soon as possible.

ACU 000974.02
ACU 000974.03
Hand Throttle Circuit Voltage Problem. Have John Deere
dealer repair at earliest convenience.
Rear PTO Circuit Voltage Problem. Have John Deere
dealer repair at earliest convenience.
ACU 001079.02
ACU 001079.03
ACU 001079.04
ACU Sensor Supply 1 Voltage Problem. Have John Deere
dealer repair as soon as possible.
ACU 001080.02
ACU 001080.03
ACU 001080.04
ACU Sensor Supply 2 Voltage Problem. Have John Deere
dealer repair as soon as possible.
ECU Message Missing. Check fuse F24. Have John Deere
dealer repair as soon as possible.
PTI or PTP Message Missing. Have John Deere dealer
repair as soon as possible.
SFA Message Missing. Have John Deere dealer repair as
soon as possible.
CAB Message Missing. Check fuse F22. Have John Deere
dealer repair as soon as possible.
Single Lever Control (If Equipped) - Hand Presence Switch
Problem. Move hand to show operator is in place. If code
still exists, have John Deere dealer repair at earliest
convenience.
ACU 523776.02
ACU 523801.02
ACU 523804.02
ACU 523804.03
ACU 523804.04
Single Lever Control Problem. To keep working, use SCV
III and IV controls. Go to CommandCenter and disable
single lever control. Have John Deere dealer repair at
earliest convenience.

ACU 523805.02
ACU 523805.03
ACU 523805.04
ACU 523923.02
ACU 523923.03
ACU 523923.04
SCV I Control Lever Switch/Sensor Problem. Have John
Deere dealer repair at earliest convenience.
OU1092A,0000020 -19-28SEP06-2/27
ACU 523953.02
ACU 523953.03
ACU 523953.04
Speed Control Lever Circuit Problem. Have John Deere
dealer repair at earliest convenience.
Set Speed Adjuster Problem. Have John Deere dealer
repair at earliest convenience.
Engine Load to High in Manual Mode. Reduce load and/or
ballast. If code returns, have John Deere dealer repair at
earliest convenience.
ACU 523960.17
ACU 523960.31
Operator Not Seated or Faulty Sensor. Check and repair if
needed.
Park Engaged While in Gear. Restart tractor, operate
tractor in forward gear. If code returns, have John Deere
dealer repair at earliest convenience.

Park Lock Engagement Problem. Restart tractor. Operate
vehicle slowly in forward gear. If code returns, have John
Deere dealer repair at earliest convenience.
MFWD Speed Incorrect. Is a function of traction control.
Very important if pulling trailers. Have John Deere dealer
repair at earliest convenience.
Transmission Come Home
Mode
Have John Deere dealer repair as soon as possible.
ACU 523970.02
ACU 523970.03
ACU 523970.04
Front Hitch Circuit Problem. Have John Deere dealer
repair at earliest convenience.
Transmission In Gear At Start-Up. Restart vehicle with
transmission in park. If code returns, have John Deere
dealer repair at earliest convenience.
ACU 524014.31
ACU 524017.13
ACU 524017.31
ACU 524018.31
ACU 524019.31
Left-Hand Reverser Problem. Have John Deere dealer
repair at earliest convenience.
ACU 524021.31
Multiple Reverser Switches Conflict. Have John Deere
dealer repair at earliest convenience.
ACU 524022.31
ACU 524023.31
ACU 524024.31
ACU 524025.31
ACU 524026.31
ACU 524027.31
ACU 524030.31
ACU 524031.31
ACU 524032.31
Left-Hand Reverser Circuit Problem. Have John Deere
dealer repair at earliest convenience.

ACU 524034.31
ACU 524036.31
Front Hitch Valve Control Lever Switch/Sensor Circuit
Conflict. Have John Deere dealer repair at earliest
convenience.
OU1092A,0000020 -19-28SEP06-3/27
ACU 524101.03
ACU 524101.04
Front Hitch Valve Control Lever Sensor Circuit Voltage
Problem. Have John Deere dealer repair at earliest
convenience.
SCV Control Lever Switch/Sensor Circuit Conflict. Have
John Deere dealer repair at earliest convenience.
ACU 524102.03
ACU 524102.04
SCV Control Lever Sensor Circuit Voltage Problem. Have
John Deere dealer repair at earliest convenience.
ACU 524103.02
ACU 524103.03
ACU 524103.04
ACU 524104.02
ACU 524104.03
ACU 524104.04
ACU 524105.02
ACU 524105.03
ACU 524105.04
SCV Control Lever Circuit Problem. Have John Deere
dealer repair at earliest convenience.

ACU 524212.02
ACU 524212.03
ACU 524212.04
Rear Hitch Control Lever Circuit Problem. Have John
Deere dealer repair at earliest convenience.
ACU 524224.02
ACU 524224.14
Rear PTO Switch Circuit Problem. Have John Deere dealer
repair at earliest convenience.
Transmission Relay Circuit Problem. Have John Deere
dealer repair at earliest convenience.
Transmission Enable Relay Circuit Fault. Have John Deere
dealer repair at earliest convenience.
ActiveSeat Unit Diagnostic Trouble Codes (ASU)
Seat Pressure Control Solenoid Problem. Have John Deere
dealer repair at earliest convenience.
ASU Not Calibrated. Have John Deere dealer repair as
soon as possible.
ClimaTrak Display Codes (ATC) - If Equipped
IMPORTANT: Check the cleanliness of the condenser at the front of the tractor and
make sure the cab recirculation air filter is not plugged for all ATC diagnostic trouble
codes. If the codes return, contact your John Deere dealer as soon as possible.
Front Brake Control Unit Diagnostic Trouble Codes (BRC)
BRC 000158.04
BRC 000168.04
Switched Supply Voltage Problem. Visually inspect around
the batteries and alternator for any visual signs of
damage or accumulated debris. Restart vehicle. If code
returns, have John Deere dealer repair as soon as
possible.
BRC 000629.12
BRC 000630.13
BRC Control Unit Problem. Have John Deere dealer repair
as soon as possible.

OU1092A,0000020 -19-28SEP06-4/27
BRC 001079.03
BRC 001079.04
BRC 001079.05
BRC 001079.06
Sensor Supply Voltage Problem. Have John Deere dealer
repair as soon as possible.
BRC 522280.00
Secondary Brake Pressure High. Have John Deere dealer
repair as soon as possible.
Secondary Brake Pressure Low. Have John Deere dealer
repair as soon as possible.
Control Unit Attached to Incompatible Harness. Have
John Deere dealer repair as soon as possible.
BRC 523837.00
BRC 523837.03
BRC 523837.04
BRC 523837.13
Rear Brake Pressure Circuit Problem. Have John Deere
dealer repair as soon as possible.
BRC 523840.00
BRC 523840.01
BRC 523840.03
BRC 523840.04
BRC 523840.13
Front Brake Pressure Circuit Problem. Have John Deere
dealer repair as soon as possible.
BRC 523844.05
BRC 523844.06
Front Brake Solenoid Circuit Problem. Have John Deere
dealer repair as soon as possible.

Control Unit Problem. Have John Deere dealer repair as
soon as possible.
Switched Supply Voltage Problem. Check Fuse F24.
Restart vehicle. If code returns, have John Deere Dealer
repair as soon as possible.
Right Brake Pedal Switch Problem. Have John Deere
dealer repair as soon as possible.
BRC 524162.19
BRC 524169.19
Left Brake Pedal Switch Problem. Have John Deere dealer
repair as soon as possible.
Cab Control Unit Diagnostic Trouble Codes (CAB)
CAB 000091.02
CAB 000091.03
CAB 000091.04
Foot Throttle Sensor Problem. Have John Deere dealer
repair at earliest convenience.
CAB 001079.02
CAB 001079.03
CAB 001079.04
CAB Supply Voltage Problem. Have John Deere dealer
repair as soon as possible.
Seat Switch Circuit Problem. Have John Deere dealer
repair at earliest convenience.
OU1092A,0000020 -19-28SEP06-5/27

Turn Signal Switch Problem. Have John Deere dealer
repair at earliest convenience.
Rear PTO Remote Switch Problem. Have John Deere
dealer repair at earliest convenience.
Secondary Hand Brake on While Moving. Disengage hand
brake. If code returns, have John Deere dealer repair as
soon as possible.
Left-Hand Reverser Circuit Problem. Have John Deere
dealer repair at earliest convenience.
CAB Switched Power Voltage Problem. Check fuse F15.
Restart vehicle. If code returns, have John Deere dealer
repair returns at earliest convenience.
Left-Hand Reverser Lever Type Not Selected. Have John
Deere dealer repair at earliest convenience.
Left-Hand Reverser Power Circuit Fault. Have John Deere
dealer repair at earliest convenience.
CAB 524018.31
CAB 524019.31
Left-Hand Reverser Transition Fault. Lever is held in an
invalid position. Move lever to PARK. Have John Deere
dealer repair at earliest convenience.
Left-Hand Reverser in Gear at Power Up. Place reverser
lever in PARK position. Restart vehicle. If code returns,
have John Deere dealer repair at earliest convenience.

CAB 524021.31
CAB 524022.31
CAB 524023.31
CAB 524024.31
CAB 524025.31
CAB 524026.31
CAB 524027.31
Left-Hand Reverser Circuit Problem. Have John Deere
dealer repair at earliest convenience.
CAB 524030.31
CAB 524031.31
CAB 524032.31
CAB 524034.31
CAB 524036.31
Left-Hand Reverser Circuit Problem. Have John Deere
dealer repair at earliest convenience.
CAB 524166.02
CAB 524166.03
CAB 524166.04
CAB 524166.13
CAB 524166.30
Right Brake Pedal Circuit Problem. Have John Deere
dealer repair at earliest convenience.
OU1092A,0000020 -19-28SEP06-6/27
CAB 524169.02
CAB 524169.03
CAB 524169.04
CAB 524169.13
CAB 524169.30
Left Brake Pedal Circuit Problem. Have John Deere dealer
repair at earliest convenience.
CAB 524173.02
CAB 524173.03
CAB 524173.04
Clutch Pedal Sensor Circuit Conflict. Have John Deere
dealer repair at earliest convenience.

Central Control Unit Diagnostic Trouble Codes (CCU)
CCU 000090.03
CCU 000090.04
Rear PTO Oil Temperature Circuit Problem. Have John
Deere dealer repair at earliest convenience.
Fuel Level Circuit Problem. Turn key switch to RUN
position (engine off). Check fuel level. If code returns,
have John Deere dealer repair at earliest convenience.
Turn key switch to RUN position (engine off). Check fuel
level. If code returns have John Deere dealer repair at
earliest convenience.
Engine Air Filter Restricted
Clean or replace engine air filter.
CCU 000107.03
CCU 000107.04
Engine Air Filter Restriction Sensor Voltage Problem. Have
John Deere dealer repair at earliest convenience.
Engine Air Filter Restricted
Engine Air Filter Becoming Restricted. Clean or replace
engine air filter.
Engine Air Filter Restricted
Engine Air Filter Restricted, Power Derated. Clean or
replace engine air filter.
Rear Differential Lock Circuit Problem. Have John Deere
dealer repair at earliest convenience.
Rear PTO Sensor Voltage Problem. Have John Deere
dealer repair at earliest convenience.
CCU 001079.03
CCU 001079.04
CCU Sensor Supply Voltage Problem. Have John Deere
dealer repair at earliest convenience.

This code will generate when vehicle is started and air
brake pressure is insufficient to disengage trailer brakes.
It may be necessary to wait over 1 minute for brakes to
release. Bleed excess moisture from air brake reservoir. If
code returns, have John Deere dealer repair as soon as
possible.
Hydraulic Oil Temperature
High
Check hydraulic oil level in sight glass on rear differential.
Inspect transmission/hydraulic oil cooler. If code returns,
have John Deere dealer repair immediately.
CCU 001638.03
CCU 001638.04
Hydraulic Oil Temperature Circuit Problem. Have John
Deere dealer repair at earliest convenience.
OU1092A,0000020 -19-28SEP06-7/27
Hydraulic Oil Temperature
High
Check hydraulic oil level in sight glass on rear differential.
Inspect transmission-hydraulic oil cooler. Restart vehicle.
Operate vehicle at rated speed for 1 - 2 minutes. If code
returns, have John Deere dealer repair as soon as
possible.
Hydraulic Oil Filter
Restricted
Check and/or replace hydraulic oil filter. Restart vehicle.
Operate vehicle at rated speed for 1 - 2 minutes. If code
returns, have John Deere dealer repair as soon as
possible.
Rear PTO Shaft Turning Too Fast. Check that PTO shaft
and PTO speed lever match. Restart vehicle. If code
returns, have John Deere Dealer repair at earliest
convenience.

Rear PTO Underspeed. Check that PTO shaft and PTO
speed lever match. Have John Deere dealer repair if code
returns at earliest convenience.
Rear PTO Calibration not Performed or Incomplete. Have
John Deere dealer repair as soon as possible.
Back Up Alarm Circuit Fault. Have John Deere dealer
repair as soon as possible.
Implement Management
System
IMS Aborted Sequence Because of Lack of Response from
Hitch/SCV Control Unit. Have John Deere dealer repair at
earliest convenience.
CCU Switched Supply Voltage Low. Have John Deere
dealer repair at earliest convenience.
Leaving Differential Lock on for more than 15 seconds will
generate this code. Have John Deere dealer repair at
earliest convenience.
PTO is Disabled but the Switch is on. Turn all PTO
switches OFF. Restart vehicle. If code returns, have John
Deere dealer repair at earliest convenience.
MFWD Circuit Problem. Have John Deere dealer repair at
earliest convenience.
Implement Management
System
IMS was turned off while commanding an MFWD mode
other than what the MFWD switch has commanded. Have
John Deere dealer repair at earliest convenience.
PTO Engaged while Operator not Present. Have John
Deere dealer repair as soon as possible.

Rear PTO Solenoid Circuit Problem. Have John Deere
dealer repair at earliest convenience.
Rear PTO Remote Enable Switch ON and Rear PTO Fender
Switch OFF. This is normal and serves as a safety alert.
Cab Load Center (CLC) Diagnostic Trouble Codes
OU1092A,0000020 -19-28SEP06-8/27
CLC 000158.00
CLC 000158.01
CLC 000158.17
CLC 000158.18
CAB Switched Supply Voltage Problem. Have John Deere
dealer repair as soon as possible.
CLC Circuit Current High. Remove all operator customized
accessories such as flood lights, hazard lights and window
wipers. Have John Deere dealer repair at earliest
convenience.
CLC 002360.05
CLC 002360.06
Rear Fender Flood Light Circuit Current Problem. Check
condition of light bulb. If code still exists, have John Deere
dealer repair at earliest convenience.

CLC 002362.05
CLC 002362.06
Rear Roof Flood Light Circuit Current Problem. Check
condition of light bulb. If code still exists, have John Deere
dealer repair at earliest convenience.
CLC 002364.05
CLC 002364.06
Mid Body Flood Light Circuit Current Problem. Check
condition of light bulb. If code still exists, have John Deere
dealer repair at earliest convenience.
CLC 002366.05
CLC 002366.06
Side Roof Flood Light Circuit Current Problem. Check
condition of light bulb. If code still exists, have John Deere
dealer repair at earliest convenience.
CLC 002368.05
CLC 002368.06
Left Turn Signal Light Circuit Current Problem. Check
condition of light bulb. If code still exists, have John Deere
dealer repair at earliest convenience.
CLC 002370.05
CLC 002370.06
Right Turn Signal Light Circuit Current Problem. Check
condition of light bulb. If code still exists, have John Deere
dealer repair at earliest convenience.
CLC 002372.05
CLC 002372.06
Brake Light Circuit Current Problem. Check condition of
light bulb. If code still exists, have John Deere dealer
repair at earliest convenience.
CLC 002378.05
CLC 002378.06
Tail Light Circuit Current Problem. Check condition of light
bulb. If code still exists, have John Deere dealer repair at
earliest convenience.
CLC 002394.05
CLC 002394.06
Trailer Flood Light Circuit Overload or Short Circuit.
Unplug 7-pin connector to verify code still exists. Have
John Deere dealer repair at earliest convenience.
Front Wiper Switch Circuit Fault. Cycle switch ON and
OFF. If code still exists, have John Deere dealer repair at
earliest convenience.

Rear Wiper Switch Circuit Fault. Cycle switch ON and OFF.
If code still exists, have John Deere dealer repair at
earliest convenience.
Main Light Switch Circuit Fault. Cycle switch ON and OFF.
If code still exists, have John Deere dealer repair at
earliest convenience.
ELX Output Circuit Current High. Have John Deere dealer
repair at earliest convenience.
CLC 522433.05
CLC 522433.06
Rear Wiper Motor Circuit Current Problem. Have John
Deere dealer repair at earliest convenience.
CLC 522434.05
CLC 522434.06
Front Wiper Motor Low Speed Circuit Current Problem.
Have John Deere dealer repair at earliest convenience.
OU1092A,0000020 -19-28SEP06-9/27
CLC 522435.05
CLC 522435.06
Front Wiper Motor High Speed Circuit Current Problem.
Have John Deere dealer repair at earliest convenience.
PTO Remote Enable Switch Problem. Have John Deere
dealer repair at earliest convenience.
Communication Bus or Vehicle Load Center Wakeup
Circuit Current High. Have John Deere dealer repair at
earliest convenience.

Transmission Selector Circuit Fault. Have John Deere
dealer repair at earliest convenience.
Auto Mode and Brake Assist Mode High. Have John Deere
dealer repair at earliest convenience.
Engine Control Unit Diagnostic Trouble Codes (ECU)
ECU 000097.03
ECU 000097.04
Water In Fuel Signal Problem. Have John Deere dealer
repair as soon as possible.
Engine Water Separator
Full
Remove water from separator.
Check engine oil level. If code returns, have John Deere
dealer repair immediately.
ECU 000100.03
ECU 000100.04
Engine Oil Pressure Input Voltage Problem. Have John
Deere dealer repair as soon as possible.
Check engine oil level. If code returns, have John Deere
dealer repair as soon as possible.
Sensor Indicates Oil Pressure When Engine Is OFF. Have
John Deere dealer repair at earliest convenience.
Manifold Air Pressure Sensor Problem. Have John Deere
dealer repair at earliest convenience.
ECU 000102.03
ECU 000102.04
Manifold Air Pressure Voltage Problem. Have John Deere
dealer repair as soon as possible.

Turbo Speed Overspeed. If operating at high altitude,
reduce load on engine. If problem continues, have John
Deere dealer repair as soon as possible.
ECU 000103.05
ECU 000103.06
ECU 000103.08
ECU 000103.31
Turbo Speed Error. Have John Deere dealer repair as soon
as possible.
Engine Air Temperature
High
Intake Air Temperature High. Check coolant level. Inspect
and clean radiator. If code returns, have John Deere
dealer repair immediately.
ECU 000105.03
ECU 000105.04
Manifold Air Temperature Voltage Problem. Have John
Deere dealer repair as soon as possible.
Engine Air Temperature
High
Manifold Air Temperature is above Specification. Check
coolant level. Inspect and clean radiator. If code returns,
have John Deere dealer repair as soon as possible.
OU1092A,0000020 -19-28SEP06-10/27
Engine Air Temperature
High
Manifold Air Temperature Moderately High. Check
coolant level. Inspect and clean radiator. If code returns,
have John Deere dealer repair as soon as possible.
Barometric Pressure Sensor Problem. Have John Deere
dealer repair at earliest convenience.

Engine Coolant
Temperature High
Check coolant level. Inspect and clean radiator. If code
returns, have John Deere dealer repair immediately.
ECU 000110.03
ECU 000110.04
Engine Coolant Temperature Input Voltage Problem.
Have John Deere dealer repair as soon as possible.
Engine Coolant
Temperature High
Check coolant level. Inspect and clean radiator. If code
returns, have John Deere dealer repair at earliest
convenience.
Engine Coolant
Temperature High
Check coolant level. Inspect and clean radiator. If code
returns, have John Deere dealer repair as soon as
possible.
Engine Coolant
Temperature Low
Engine Coolant Temperature Low. Warm up engine. If
problem continues, have John Deere dealer repair as
soon as possible.
ECU 000157.03
ECU 000157.04
Fuel Rail Pressure Input Voltage Problem. Have John
Deere dealer repair immediately.
Fuel Rail Pressure Loss Detected. Have John Deere dealer
repair as soon as possible.
Fuel Rail Pressure Not Developed. Have John Deere
dealer repair as soon as possible.
Engine Control Unit Power Down Error. Have John Deere
dealer repair at earliest convenience.
Fuel Temperature High. Check coolant level. Inspect and
clean radiator. Check to see if code returns. Have John
Deere dealer repair immediately.

ECU 000174.03
ECU 000174.04
Fuel Temperature Input Voltage Problem. Have John
Deere dealer repair as soon as possible.
Check coolant level. Inspect and clean radiator and fuel
cooler. If code returns, have John Deere dealer repair as
soon as possible.
Result of downshifting, throttle back. If code returns,
have John Deere dealer repair immediately.
ECU 000237.02
ECU 000237.13
ECU 000237.31
Vehicle Serial Number Invalid. Have John Deere dealer
repair as soon as possible.
EGR Temperature Sensor Input Voltage Problem. Most
Sever Level. Have John Deere dealer repair immediately.
OU1092A,0000020 -19-28SEP06-11/27
ECU 000412.03
ECU 000412.04
EGR Temperature Sensor Input Voltage Problem. Have
John Deere dealer repair as soon as possible.
ECU 000412.15
ECU 000412.16
EGR Temperature Higher than Expected. Have John Deere
dealer repair as soon as possible.

ECU 000611.03
ECU 000611.04
Electronic Injector Wiring Problem. Have John Deere
dealer repair as soon as possible.
Electronic Injector Supply Voltage Problem. Have John
Deere dealer repair as soon as possible.
ECU Memory Problem. Have John Deere dealer repair as
soon as possible.
ECU Programming Error. Have John Deere dealer repair
immediately.
Cam Sensor Open. Have John Deere dealer repair as soon
as possible.
Cam Sensor Shorted. Have John Deere dealer repair as
soon as possible.
ECU 000636.02
ECU 000636.08
ECU 000636.10
Pump Position Sensor Problem. Have John Deere dealer
repair at earliest convenience.
ECU 000637.02
ECU 000637.05
ECU 000637.06
ECU 000637.07
Crank Position Sensor Problem. Have John Deere dealer
repair as soon as possible.
ECU 000637.08
ECU 000637.10
Crank Position Input Problem. Have John Deere dealer
repair as soon as possible.
Turbo Actuator Supply Voltage Low or Intermittent. Have
John Deere dealer repair as soon as possible.

ECU 000641.05
ECU 000641.13
Have John Deere dealer repair as soon as possible.
Communication on Error to Turbo. Have John Deere
dealer repair as soon as possible.
Turbo Actuator Over Temperature. Have John Deere
dealer repair as soon as possible.
Upper Fan Drive Output 1 Shorted or Open. Inspect
wiring leads on solenoid coil above fan drive piston
housing. Have John Deere dealer repair as soon as
possible.
ECU 000651.02
ECU 000651.13
Electronic Fuel Injector Problem. Have John Deere dealer
repair at earliest convenience.
OU1092A,0000020 -19-28SEP06-12/27
ECU 000651.05
ECU 000651.06
ECU 000651.07
ECU 000652.02
ECU 000652.05
ECU 000652.06
ECU 000652.07
ECU 000652.13
ECU 000653.02
ECU 000653.05
ECU 000653.06
ECU 000653.07
ECU 000653.13
ECU 000654.02
ECU 000654.05
Electronic Fuel Injector Problem. Have John Deere dealer
repair as soon as possible.

ECU 000654.06
ECU 000654.07
ECU 000654.13
ECU 000655.02
ECU 000655.05
ECU 000655.06
ECU 000655.07
ECU 000655.13
ECU 000656.02
ECU 000656.05
ECU 000656.06
ECU 000656.07
ECU 000656.13
ECU 000676.03
ECU 000676.05
Glow Plug Relay Output Problem. Have John Deere dealer
repair as soon as possible.
Electric Lift Pump in Fuel Filter Base Short/Open. Have
John Deere dealer repair at earliest convenience.
Engine Protection Shutdown. Have John Deere dealer
repair as soon as possible.
ECU Temperature High. Check area around ECU for
adequate air flow. If problem continues, have John Deere
dealer repair immediately.
Internal ECU Temperature High. Check area around ECU
for adequate air flow. If problem continues, have John
Deere dealer repair as soon as possible.
ECU 001172.03
ECU 001172.04
Compressor Inlet Temperature Input Voltage Problem.
Have John Deere dealer repair at earliest convenience.
Exhaust Temperature is High. Have John Deere dealer
repair immediately.

Exhaust Temperature is Higher than Specification. Have
John Deere dealer repair as soon as possible.
OU1092A,0000020 -19-28SEP06-13/27
ECU 001347.03
ECU 001347.05
Pump control valve problem. Have John Deere dealer
repair as soon as possible.
Fuel Rail Pressure Control Problem. Check fuel filter, If
code returns, have John Deere dealer repair as soon as
possible.
One of the Derate Conditions Exists on Engine. Have John
Deere dealer repair at earliest convenience.
ECU 001639.01
ECU 001639.16
ECU 001639.18
ECU 002005.09
Fan Speed Signal Problem. Have John Deere dealer repair
at earliest convenience.
Communication Error. Allow tractor to run for 10 minutes
to clear code.
CAB Message Missing. Have John Deere dealer repair at
earliest convenience.
ECU 002049.09
ECU 002071.09
Control Unit Signal Missing. Have John Deere dealer
repair at earliest convenience.

Charge Air Outlet Temperature Higher than Expected
(Most Severe). Have John Deere dealer repair
immediately.
ECU 002630.03
ECU 002630.04
Charge Air Outlet Temperature Input Voltage Problem.
Have John Deere dealer repair as soon as possible.
ECU 002630.15
ECU 002630.16
Charge Air Outlet Temperature Higher than Expected
(Less Severe). Have John Deere dealer repair as soon as
possible.
ECU 002659.02
ECU 002659.15
ECU 002659.17
EGR Problem. Have John Deere dealer repair as soon as
possible.
Compressor Outlet Temperature High. Have John Deere
dealer repair as soon as possible.
ECU 002791.02
ECU 002791.03
ECU 002791.04
ECU 002791.07
ECU 002791.13
ECU 002791.14
ECU 002791.31
EGR Valve Error. Have John Deere dealer repair as soon as
possible.
ECU 002795.07
ECU 002795.12
Variable Geometry Turbo Control Error. Have John Deere
dealer repair as soon as possible.
ECU 003509.03
ECU 003509.04
Fuel Rail Pressure Sensor Supply Voltage Problem. Have
John Deere dealer repair immediately.
OU1092A,0000020 -19-28SEP06-14/27

ECU 003510.03
ECU 003510.04
ECU 003511.03
ECU 003511.04
ECU 003512.03
ECU 003512.04
ECU 003513.03
ECU 003513.04
ECU Sensor Voltage Problem. Have John Deere dealer
repair as soon as possible.
ECU Default DTC. Have John Deere dealer repair at
earliest convenience.
Hitch Control Unit Diagnostic Trouble Codes (HCU)
HCU 000158.04
HCU 000168.04
HCU Supply Voltage Low. Visually inspect around the
batteries and alternator for any visual signs of damage or
accumulated debris. Check fuse F30. If code still exists,
have John Deere dealer repair at earliest convenience.
HCU Not Calibrated. Have John Deere dealer repair at
earliest convenience.
HCU 001079.03
HCU 001079.04
HCU Sensor Supply Voltage Problem. Have John Deere
dealer repair at earliest convenience.
HCU 001873.02
HCU 001873.03
HCU 001873.04
HCU 001873.11
Rear Hitch Position Sensor Problem. Have John Deere
dealer repair at earliest convenience.
HCU Calibration Fault/Rear Hitch Position Sensor Circuit.
Have John Deere dealer calibrate hitch at earliest
convenience.

HCU 001881.03
HCU 001881.04
HCU 001881.13
Rear Hitch Draft Sensor Problem. Have John Deere dealer
repair at earliest convenience.
Vehicle Speed Update Fault. Have John Deere dealer
repair at earliest convenience.
ACU Message Missing. Have John Deere dealer repair at
earliest convenience.
CCU Message Missing. Have John Deere dealer repair at
earliest convenience.
HCU 521001.02
HCU 521001.05
HCU 521001.06
HCU 521001.07
HCU 521001.11
HCU 521002.05
HCU 521002.07
HCU 521002.06
Rear Hitch Circuit Problem. Have John Deere dealer repair
at earliest convenience.
Wire Connector Fault. Have John Deere dealer repair at
earliest convenience.
OU1092A,0000020 -19-28SEP06-15/27
Hydraulic Option Configuration Problem. Hook up last
used implement and cycle key switch ON and OFF to
reset.

Control Unit Problem. Have John Deere dealer repair at
earliest convenience.
Operator Trying to use Hitch while Disabled or not
Available. Have John Deere dealer repair at earliest
convenience.
Switched Supply Voltage Problem. Visually inspect around
the batteries and alternator for any visual signs of
damage or accumulated debris. Restart vehicle. If code
returns, have John Deere dealer repair at earliest
convenience.
HCU 524212.19
HCU 524212.31
Rear Hitch Control Lever Problem. Have John Deere
dealer repair at earliest convenience.
Instrument Control Unit Diagnostic Trouble Codes (ICU)
ECU Message Missing. Check fuse F9. Restart vehicle. If
code returns, have John Deere dealer repair as soon as
possible.
PTI or PTQ Message Missing. Check fuse F6 for IVT or F35
PowrQuad Plus. Restart vehicle. If code returns, have
John Deere dealer repair as soon as possible.
BRC Message Missing. Have John Deere dealer repair at
earliest convenience.
ACU Message Missing. Check fuse F13 for IVT or F35 for
PowrQuad Plus. Restart vehicle. If code returns, have
John Deere dealer repair as soon as possible.
SSU Message Missing. Have John Deere dealer repair at
earliest convenience.

SFA Message Missing. Check fuse F24. Restart vehicle. If
code returns, have John Deere dealer repair as soon as
possible.
ATC Message Missing. Check fuse F42. Restart vehicle. If
code returns, have John Deere dealer repair as soon as
possible.
VLC Message Missing. Have John Deere dealer repair as
soon as possible.
SCU Message Missing. Check fuse F24. Restart vehicle. If
code returns, have John Deere dealer repair as soon as
possible.
HCU Message Missing. Have John Deere dealer repair as
soon as possible.
PTF Message Missing. Check fuse F15. Restart vehicle. If
code returns, have John Deere dealer repair as soon as
possible.
CAB Message Missing. Check fuse F35. Restart vehicle. If
code returns, have John Deere dealer repair as soon as
possible.
CLC Message Missing. Have John Deere dealer repair as
soon as possible.
OU1092A,0000020 -19-28SEP06-16/27

ASU Message Missing. Check fuses F35 for IVT and F45
PowrQuad Plus. Restart vehicle. If code returns, have
John Deere dealer repair as soon as possible.
CCU Message Missing. Check fuses F6 for IVT and F35 for
PowrQuad Plus. Restart vehicle. If code returns, have
John Deere dealer repair as soon as possible.
ICU Message Missing. Check fuse F28. Restart vehicle. If
code returns, have John Deere dealer repair as soon as
possible.
SCO Message Missing. Check fuse F24. Restart vehicle. If
code returns, have John Deere dealer repair as soon as
possible.
SUP Message Missing. Check fuse F23. Restart vehicle. If
code returns, have John Deere dealer repair as soon as
possible.
TEC Message Missing. Check fuse F23. Restart vehicle. If
code returns, have John Deere dealer repair as soon as
possible.
No CAN messages received from any source address
within time-out period.
Engine is Currently too Cold to Start and is Firing the Glow
Plugs in Preparation for Starting. Engine may be safely
started at conclusion of countdown.
Front PTO Control Unit Diagnostic Trouble Codes (PTF)

PTF Supply Voltage Low. Have John Deere dealer repair at
earliest convenience.
Front PTO Shaft is Turning too Fast. Restart vehicle.
Engage Front PTO. Set engine to full throttle. If code
returns, have John Deere dealer repair as soon as
possible.
Front PTO Underspeed Detected. Restart vehicle and
Engage Front PTO. Set engine to full throttle. If code
returns, have John Deere dealer repair at earliest
convenience.
Front PTO Not Calibrated. Have John Deere dealer repair
at earliest convenience.
PTO Engaged While Operator Not Seated. Sit in operators
seat. Restart vehicle and cycle front PTO switch. If code
returns, have John Deere dealer repair as soon as
possible.
Front PTO Circuit Problem. Have John Deere dealer repair
at earliest convenience.
PTF 523906.03
PTF 523906.04
Front PTO Oil Temperature Circuit Problem. Have John
Deere dealer repair at earliest convenience.
Control Unit Problem. Check fuse F35. Restart vehicle. If
code returns, have John Deere dealer repair at earliest
convenience.
PTF 524216.02
PTF 524216.31
Front PTO Switch Problem. Have John Deere dealer repair
at earliest convenience.

OU1092A,0000020 -19-28SEP06-17/27
Solution
IVT Transmission Control Unit Diagnostic Trouble Codes (PTI)
PTI 000126.15
PTI 000126.16
Transmission Oil Filter
Restricted
Check condition and service interval of transmission oil
and filter. Restart vehicle. Warm oil to normal operating
temperature. If code returns, have John Deere dealer
repair as soon as possible.
Transmission Oil Pressure
Low
Restart vehicle. Warm oil to normal operating
temperature. If code returns, have John Deere dealer
repair at earliest convenience.
PTI 000127.02
PTI 000127.04
Transmission Pump Pressure Sensor Problem. Have John
Deere dealer repair at earliest convenience.
Transmission Oil Pressure
Low
Transmission Pump Pressure Low. Have John Deere
dealer repair as soon as possible.
PTI 000158.01
PTI 000168.01
Control Unit Supply Voltage Problem. Have John Deere
dealer repair at earliest convenience.
Engine Overspeed. Reduce engine RPM. If code returns,
have John Deere dealer repair as soon as possible.
Engine Speed Mismatch. Have John Deere dealer repair at
earliest convenience.
Operating tractor downhill with a heavy rear load may
cause the rear differential to overspeed the transmission
output shaft. Slow vehicle. If code returns, have John
Deere dealer repair as soon as possible.

Transmission Speed Sensors and Calculated "Expected"
Speed Differ by more than 200 rpm. Have John Deere
dealer repair at earliest convenience.
Park Brake Solenoid Circuit Problem. Have John Deere
dealer repair at earliest convenience.
PTI 000734.05
PTI 000735.05
PTI 000736.05
Clutch/Brake Solenoid Circuit Problem. Have John Deere
dealer repair at earliest convenience.
PTI 000754.18
PTI 000755.18
PTI 000756.18
Transmission Oil Pressure
Low
Clutch Enable Pressure Problem. Have John Deere dealer
repair as soon as possible.
Control Unit Sensor Voltage Problem. Have John Deere
dealer repair at earliest convenience.
ECU Message Missing. Have John Deere dealer repair at
earliest convenience.
ACU Message Missing. Have John Deere dealer repair at
earliest convenience.
Transmission Oil Filter
Restricted
Check the condition and service interval of the
transmission oil and filter. If code returns, have John
Deere dealer repair immediately.
OU1092A,0000020 -19-28SEP06-18/27

PTI 524042.16
PTI 524227.00
PTI 524227.16
Transmission Oil Filter
Restricted
Transmission Oil Filter Bypassed. Check the condition and
service interval of the transmission oil and filter. If code
returns, have John Deere dealer repair as soon as
possible.
Direction Sensing Incorrect. Have John Deere dealer
repair as soon as possible.
PTI 524228.05
PTI 524228.11
Park Sump Block Circuit Problem. Have John Deere dealer
repair at earliest convenience.
Hydro Control Solenoid Circuit Problem. Have John Deere
dealer repair at earliest convenience.
Clutch Enable Solenoid Circuit Problem. Have John Deere
dealer repair at earliest convenience.
Park Brake Pressure Low/Gear Commanded. Stop engine,
have John Deere dealer repair immediately.
PTI 524232.02
PTI 524232.04
Park Brake Pressure Sensor Problem. Have John Deere
dealer repair at earliest convenience.
Transmission Oil Pressure
Low
Park Brake Pressure Low in Come Home Mode. Perform
Park Brake Release Procedure (see section 80). Wait 5-10
minutes. If code returns, have John Deere dealer repair
immediately.
PTI 524232.16
PTI 524232.17
Park Brake Pressure Problem. Have John Deere dealer
repair as soon as possible.

Transmission Oil Pressure
Low
Park Brake Pressure Low. Have John Deere dealer repair
as soon as possible.
Hydro Fixed Unit Overspeed. Have John Deere dealer
repair as soon as possible.
PTI 524233.07
PTI 524233.15
PTI 524233.16
Hydro Speed Sensor Problem. Have John Deere dealer
repair at earliest convenience.
PTI 524234.02
PTI 524234.04
Clutch Pressure Circuit Problem. Have John Deere dealer
repair at earliest convenience.
Neutral and Park or Scroll Switches on During Start-Up.
Restart vehicle. If code returns, have John Deere dealer
repair at earliest convenience.
Transmission Lever Not in
Park
Left-Hand Reverser Lever Not in Park or Neutral at Power
Up. Place lever in park or neutral. Restart vehicle. If code
returns, have John Deere dealer repair at earliest
convenience.
No Motion / Engine Running. Have John Deere dealer
repair at earliest convenience.
No Vehicle Motion for 5 Seconds After "Come-Home"
Mode Selected. Have John Deere dealer repair at earliest
convenience.
OU1092A,0000020 -19-28SEP06-19/27

Carrier or Fixed Unit Speed Incorrect. Have John Deere
dealer repair at earliest convenience.
Transmission Oil Pressure
High
Transmission Park and Enable Pressures High. Have John
Deere dealer repair as soon as possible.
PTI 524243.31
PTI 524244.31
PTI 524245.31
Control Unit Command Problem. Have John Deere dealer
repair at earliest convenience.
Hydro Fixed Unit Speed Low at Start-Up. Have John Deere
dealer repair at earliest convenience.
Carrier Speed Circuit Problem. Have John Deere dealer
repair at earliest convenience.
Motion Detected with Park Brake Engaged. Restart
vehicle. Park vehicle on a slight incline. Place left-hand
reverser in PARK. Let vehicle sit for 1-2 minutes. If code
returns, have John Deere dealer repair as soon as
possible.
Operator Not Present with Transmission in Neutral. Sit in
seat. If code returns, have John Deere dealer repair as
soon as possible.
Park Brake Previously Failed/May Not Hold. Have John
Deere dealer repair as soon as possible.
Control Unit Not Commanding Park at Start-Up. Place lefthand reverser in PARK. Restart vehicle. If code returns,
have John Deere dealer repair at earliest convenience.

PTI 524254.03
PTI 524254.04
Transmission Enable Relay Circuit Voltage Problem. Verify
that there is NOT a fuse installed in F5 location. Have
John Deere dealer repair at earliest convenience.
PowrQuad Plus Transmission Control Unit Diagnostic Trouble Codes (PTQ)
PTQ Wheel Speed Message Missing. Have John Deere
dealer repair as soon as possible.
Transmission Oil Filter
Restricted
Check condition and service interval of transmission oil
filter. Restart vehicle. If code returns, have John Deere
dealer repair as soon as possible.
Transmission Oil Pressure
Low
Check transmission fluid level in sight glass on rear
differential case. Restart vehicle. If code returns, have
John Deere dealer repair immediately.
Electrical System Voltage
Low
Visually inspect around the batteries and alternator for
damage or accumulated debris. Restart vehicle. If code
returns, have John Deere dealer repair as soon as
possible.
PTQ Engine Speed Low. Have John Deere dealer repair as
soon as possible.
Transmission Underspeed. Have John Deere dealer repair
at earliest convenience.
OU1092A,0000020 -19-28SEP06-20/27

PTQ 000734.05
PTQ 000735.05
PTQ 000736.05
PTQ 000737.05
Transmission Sensor Circuit Problem. Have John Deere
dealer repair at earliest convenience.
ECU Message Missing. Check fuse F9. Restart vehicle. If
code returns, have John Deere dealer repair as soon as
possible.
ACU Message Missing. Have John Deere dealer repair as
soon as possible.
CAB Message Missing. Have John Deere dealer repair as
soon as possible.
CLC Message Missing. Have John Deere dealer repair as
soon as possible.
ICU Message Missing. Have John Deere dealer repair as
soon as possible.
Speed Control Lever Circuit Problem. Have John Deere
dealer repair at earliest convenience.
Operator Not Seated During Reverser Command. Have
John Deere dealer repair at earliest convenience.
Range Lever Park/Reverser Lever Gear Problem. Have
John Deere dealer repair at earliest convenience.
Transmission Come Home
Active
Check F5 slot for fuse. Fuse should not be installed unless
vehicle is in Come Home mode. With fuse removed,
operate vehicle for 5 minutes. If code returns, have John
Deere dealer repair as soon as possible.

Trailer Air Brake Valve Problem. Have John Deere dealer
repair as soon as possible.
PTQ 524230.03
PTQ 524230.04
PTQ 524230.05
PTQ 524234.03
PTQ 524234.04
Clutch Enable Circuit Problem. Have John Deere dealer
repair at earliest convenience.
Transmission Enable Relay Circuit Voltage Low. Have John
Deere dealer repair at earliest convenience.
Optional SCV Control Unit Diagnostic Trouble Codes (SCO)
SCO 000158.04
SCO 000168.04
Control Unit Supply Voltage Problem. Visually inspect
around the batteries and alternator for any visual signs of
damage or accumulated debris. Check fuses F12, F24 and
F51. Restart vehicle. If code returns, have John Deere
dealer repair at earliest convenience.
SCO 001963.05
SCO 001975.05
Flow Control Circuit Problem. Have John Deere dealer
repair at earliest convenience.
ACU Message Missing. Have John Deere dealer repair at
earliest convenience.
OU1092A,0000020 -19-28SEP06-21/27

CCU Message Missing. Have John Deere dealer repair at
earliest convenience.
Front Hitch External Switch Circuit Problem. Inspect front
hitch switch, harness and connectors. Restart vehicle.
Cycle front hitch switch through all positions. If code
returns, have John Deere dealer repair at earliest
convenience.
Wire Connector Fault. Incompatible connection. Have
John Deere dealer repair at earliest convenience.
SCO 523662.05
SCO 523662.06
SCO 523663.05
SCO 523663.06
Auxiliary Valve Current Problem. Have John Deere dealer
repair at earliest convenience.
SCO 523695.02
SCO 523695.19
SCO 523696.02
SCO 523696.19
External Control Message Problem. Have John Deere
dealer repair at earliest convenience.
SCO 523787.03
SCO 523787.04
Auxiliary Solenoid Voltage Problem. Visually inspect
around the batteries and alternator for any visual signs of
damage or accumulated debris. Restart vehicle. If code
returns, have John Deere dealer repair at earliest
convenience.
Control Unit Problem. Have John Deere dealer repair at
earliest convenience.
SCO 523930.05
SCO 523930.06
SCO 523931.05
SCO 523931.06
SCV Directional Valve Solenoid Current Problem. Have
John Deere dealer repair at earliest convenience.

SCO 523936.05
SCO 523936.06
SCO 523937.05
SCO 523937.06
Flow Control Valve Solenoid Current Problem. Have John
Deere dealer repair at earliest convenience.
SCO 523942.31
Operator out of seat with SCV VI on.
Operator out of seat with SCV V on.
SCO 524016.03
SCO 524016.04
Control Unit Supply Voltage Problem. Visually inspect
around the batteries and alternator for any visual signs of
damage or accumulated debris. Restart vehicle. If code
returns, have John Deere dealer repair at earliest
convenience.
SCV Control Unit Diagnostic Trouble Codes (SCU)
SCU 000158.04
SCU 000168.04
Switched Supply Voltage Problem. Visually inspect around
the batteries and alternator for any visual signs of
damage or accumulated debris. Check fuses F24, F44 and
F51. Restart vehicle. If code returns, have John Deere
dealer repair at earliest convenience.
SCU 001079.03
SCU 001079.04
Control Unit Sensor Supply Voltage Problem. Have John
Deere dealer repair at earliest convenience.
OU1092A,0000020 -19-28SEP06-22/27
SCU 001915.05
SCU 001927.05
SCU 001939.05
SCU 001951.05
Flow Control Solenoid Current Problem. Have John Deere
dealer repair at earliest convenience.

ACU Message Missing. Check fuse F13. Restart vehicle. If
code returns, have John Deere dealer repair at earliest
convenience.
CAB Message Missing. Have John Deere dealer repair at
earliest convenience.
CCU Message Missing. Have John Deere dealer repair at
earliest convenience.
Wire Connector Fault. Have John Deere dealer repair at
earliest convenience.
SCU 523693.02
SCU 523693.19
SCU 523694.02
SCU 523694.19
SCV External Control Message Problem. Have John Deere
dealer repair at earliest convenience.
SCU 523786.03
SCU 523786.04
SCU 523786.07
Remote Position Sensor Problem. Have John Deere dealer
repair at earliest convenience.
SCU 523787.03
SCU 523787.04
Control Unit Switched Supply Voltage Problem. Visually
inspect around the batteries and alternator for any visual
signs of damage or accumulated debris. Restart vehicle. If
code returns, have John Deere dealer repair at earliest
convenience.
Control Unit Problem. Have John Deere dealer repair at
earliest convenience.
Control Lever Problem. Have John Deere dealer repair at
earliest convenience.

SCU 523932.05
SCU 523932.06
SCU 523933.05
SCU 523933.06
SCU 523934.05
SCU 523934.06
SCU 523935.05
SCU 523935.06
Direction Control Solenoid Circuit Current Problem. Have
John Deere dealer repair at earliest convenience.
SCU 523938.05
SCU 523938.06
SCU 523939.05
SCU 523939.06
SCU 523940.05
SCU 523940.06
SCU 523941.05
SCU 523941.06
Flow Control Solenoid Circuit Current Problem. Have John
Deere dealer repair at earliest convenience.
OU1092A,0000020 -19-28SEP06-23/27
Operator out of seat with SCV IV on.
Operator out of seat with SCV III on.
Operator out of seat with SCV II on.
Operator out of seat with SCV I on.
SCU 524015.02
SCU 524015.19
External Command Message Missing. Have John Deere
dealer repair at earliest convenience.

SCU 524016.03
SCU 524016.04
Switched Supply Voltage Problem. Visually inspect around
the batteries and alternator for any visual signs of
damage or accumulated debris. Restart vehicle. If code
returns, have John Deere dealer repair at earliest
convenience.
SCU 524038.02
SCU 524038.19
External Control Message Missing. Restart vehicle. Cycle
SCV IV Lever through all positions. If code returns, have
John Deere dealer repair at earliest convenience.
SCU 524103.31
SCU 524104.31
SCU 524105.31
Control Lever Message Missing. Have John Deere dealer
repair at earliest convenience.
Triple-Link Suspension Control Unit Diagnostic Trouble Codes (SFA)
SFA 000158.04
SFA 000168.04
Switched Supply Voltage Problem. Visually inspect around
the batteries and alternator for any visual signs of
damage or accumulated debris. Restart vehicle. If code
returns, have John Deere dealer repair at earliest
convenience.
SFA 001079.03
SFA 001079.04
Sensor Supply Voltage Problem. Have John Deere dealer
repair at earliest convenience.
SFA 001079.05
SFA 001079.06
SFA Calibration Problem. Have John Deere dealer repair
at earliest convenience.
PTI or PTQ Message Missing. Check fuse F6 for IVT or F35
for PowrQuad Plus. Restart vehicle. If code returns, have
John Deere dealer repair at earliest convenience.
ACU Message Missing. Check fuse F13 for IVT or F35
PowrQuad Plus. Restart vehicle. If code returns, have
John Deere dealer repair at earliest convenience.

CAB Message Missing. Check fuse F35. Restart vehicle. If
code returns, have John Deere dealer repair at earliest
convenience.
Control Unit Connected to Wrong Harness. Have John
Deere dealer repair at earliest convenience.
SFA 523902.07
SFA 523903.07
Suspended Front Axle Not Responding to Commands.
Inspect front axle position sensor for linkage damage.
Restart vehicle. Operate vehicle on rough terrain for 5
minutes. If code returns, have John Deere dealer repair at
earliest convenience.
Control Unit Problem. Have John Deere dealer repair at
earliest convenience.
OU1092A,0000020 -19-28SEP06-24/27
SFA 523948.05
SFA 523948.06
SFA 523949.05
SFA 523949.06
Front Axle Current Problem. Have John Deere dealer
repair at earliest convenience.
SFA 523950.02
SFA 523950.03
SFA 523950.04
Axle Position Sensor Problem. Inspect front axle position
sensor for damage. Have John Deere dealer repair at
earliest convenience.
Switched Supply Voltage Problem. Visually inspect around
the batteries and alternator for any visual signs of
damage or accumulated debris. Restart vehicle. If code

returns, have John Deere dealer repair at earliest
convenience.
AutoTrac Steering System Control Unit Diagnostic Trouble Codes (SSU)
Wheel Speed Message Missing. Have John Deere dealer
repair as soon as possible.
Unswitched Supply Voltage Problem. Visually inspect
around the batteries and alternator for any visual signs of
damage or accumulated debris. If code returns, have John
Deere dealer repair as soon as possible.
Hydraulic Oil Temperature Message Missing. Restart
vehicle. If code returns, have John Deere dealer repair as
soon as possible.
Gear Message Missing. Check fuse F6 for IVT or F35 for
PowrQuad Plus. Restart vehicle. If code returns, have
John Deere dealer repair as soon as possible.
GPS Speed Message Missing. Check StarFire connector. If
code returns, have John Deere dealer repair as soon as
possible.
Selected Gear Message Invalid. Restart vehicle. If code
returns, have John Deere dealer repair at earliest
convenience.
Steering Control Unit Not Calibrated. Restart vehicle.
Have John Deere dealer repair as soon as possible.
SSU 001079.03
SSU 001079.04
Sensor Supply Voltage Problem. Have John Deere dealer
repair as soon as possible.

Operator Presence Message Missing. Sit in seat. Restart
vehicle. If code returns, have John Deere dealer repair as
soon as possible.
Operator Not Seated while AutoTrac in on. Sit in
operator's seat and restart vehicle. If code returns, have
John Deere dealer repair as soon as possible.
OU1092A,0000020 -19-28SEP06-25/27
SSU 001807.02
SSU 001807.03
SSU 001807.04
SSU 001807.05
SSU 001807.06
SSU 001807.10
SSU 001807.14
Steering Wheel Position Sensor Problem. Have John
Deere dealer repair as soon as possible.
ELX Message Missing. Have John Deere dealer repair at
earliest convenience.
SSU 522273.00
SSU 522273.01
Steering Valve Control Circuit Problem. Have John Deere
dealer repair as soon as possible.
Wheel Angle Sensor Problem. Have John Deere dealer
repair as soon as possible.
Terrain Compensation Module Message Missing. Check
fuse F23. Restart vehicle. If code returns, have John Deere
dealer repair as soon as possible.

SSU 522451.00
SSU 522451.01
SSU 522451.14
Steering Angle Sensor Problem. Have John Deere dealer
repair at earliest convenience.
Ag Management Solutions (AMS) Display Message
Missing. Have John Deere dealer repair as soon as
possible.
AutoTrac Activation Code Invalid. Have John Deere dealer
repair as soon as possible.
AutoTrac Resume Switch Circuit Problem. Have John
Deere dealer repair as soon as possible.
AutoTrac Steering Valve Workport Connections
Backwards. Have John Deere dealer repair as soon as
possible.
Steering Valve or Harness Faulty. Have John Deere dealer
repair as soon as possible.
Control Unit Calibration Problem. Have John Deere dealer
repair as soon as possible.
SSU 523810.00
SSU 523810.01
SSU 523821.02
Steering Valve Supply Voltage Problem. Have John Deere
dealer repair as soon as possible.
SSU 523824.03
SSU 523824.04
SSU 523824.05
SSU 523824.06
SSU 523824.10
SSU 523824.14
Steering Wheel Position Sensor Voltage Problem. Have
John Deere dealer repair as soon as possible.

OU1092A,0000020 -19-28SEP06-26/27
SSU 523826.00
SSU 523826.01
SSU 523826.02
SSU 523826.07
SSU 523826.10
SSU 523826.13
SSU 523826.14
Main Primary Steering Sensor Problem. Have John Deere
dealer repair at earliest convenience.
No Communication Data. Have John Deere dealer repair
at earliest convenience.
Tractor Equipment Control Unit Diagnostic Trouble Codes (TEC)
At Least One Non Compliant Device Connected to
Connector. Have John Deere dealer repair as soon as
possible.
Vehicle Load Center Control Unit Diagnostic Trouble Codes (VLC)
Wake Up Signal Voltage Low. Likely an open circuit. Have
John Deere dealer repair at earliest convenience.
VLC Circuit Current High. Remove all operator customized
accessories such as flood lights, hazard lights and window
wipers. Total output excessive. Have John Deere dealer
repair at earliest convenience.
CLC Message Missing. Have John Deere dealer repair at
earliest convenience.

High Beam Light Circuit Current Problem. Have John
Deere dealer repair at earliest convenience.
Low Beam Light Circuit Current Problem. Have John
Deere dealer repair at earliest convenience.
Front Outer Flood Light Circuit Current Problem. Have
John Deere dealer repair at earliest convenience.
Front Inner Flood Light Circuit Current Problem. Have
John Deere dealer repair at earliest convenience.
Center Spot Light Circuit Current Problem. Have John
Deere dealer repair at earliest convenience.
ELX Output Circuit Current High. Have John Deere dealer
repair at earliest convenience.
Rear Washer Pump Circuit Current Problem. Have John
Deere dealer repair as soon as possible.
Front Washer Pump Circuit Current Problem. Have John
Deere dealer repair at earliest convenience.
Horn Circuit Current Problem. Have John Deere dealer
repair at earliest convenience.
OU1092A,0000020 -19-28SEP06-27/27