John Deere 200 Series Parts Manual
HP1967 -UN-01JAN94
A10
200 SERIES CUTTING PLATFORMS
JOHN DEERE 224 RIGID CUTTERBAR PLATFORM WITH BAT REEL
(SPECIFICATIONS AND DESIGN SUBJECT TO CHANGE WITHOUT NOTICE)
DATE OF MANUFACTURE
MODEL NO. TYPE DATE
213 RIGID, FLEX (1976-1987)
215 RIGID, FLEX (1976-1987)
216 RIGID, FLEX (1976-1987)
218 RIGID, FLEX (1976-1987)
220 RIGID, FLEX (1976-1987)
222 RIGID, FLEX (1976-1987)
224 RIGID, FLEX (1976-1987)
230 RIGID (1979-1987)
200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99) 5-1
PN=1
A11
200 SERIES CUTTING PLATFORMS
SERIAL NUMBER PLATE
USE ALL NUMBERS, LETTERS, AND SPACES ON THE SERIAL NUMBER PLATEIN WARRANTY CORRESPONDENCE.
200 SERIAL PLATFORMS ( -579900)
ON THESE PLATFORMS, THE SERIAL NUMBER PLATE IS LOCATED ON THE LEFT-HAND SIDE OF THE FRAME.
EXAMPLE: E0216579900H
E - EQUIPMENT
0216 - PLATFORM MODEL
579900 - PLATFORM SERIAL NUMBER
H - FACTORY (HARVESTER WORKS)
200 SERIES PLATFORM (579901- )
ON THESE PLATFORMS, THE SERIAL NUMBER PLATE IS LOCATED ON THE LEFT-SIDE OF THE FRAME.
EXAMPLE: H00216R579901
216 PLATFORM
(FIRST LINE) H0 - FACTORY (HARVESTER WORKS)
0216 - PLATFORM MODEL
R - CONFIGURATION/MODEL SUFFIX
579901 - PLATFORM SEQUENCE NUMBER (SERIAL NUMBER)
(SECOND LINE) PLATFORM - PRODUCT TYPE
SERIAL NUMBER LISTING INFORMATION
SERIAL NUMBER INFORMATION IS LISTED TO SHOW ON WHICH MACHINES APART CAN BE USED; FOR EXAMPLE:
- THE PART CAN BE USED ON ALL MACHINES.
000000- THE PART CAN BE USED ON ALL MACHINES BEGINNING WITH THE SERIAL NUMBER LISTED.
-000000 THE PART CAN BE USED ON ALL MACHINES UP TO AND INCLUDING THE SERIAL NUMBER
LISTED.
000000-000000 THE PART CAN BE USED ON ALL MACHINES BETWEEN AND INCLUDING THE SERIAL NUMBERS
LISTED.
WHEN XXXXXX’S ARE LISTED IN PLACE OF A SERIAL NUMBER, A SERIAL NUMBER CHANGE WAS MADE BUT THE
EXACT SERIAL NUMBER WAS NOT AVAILABLE WHEN THE CATALOG WAS PRODUCED.
COPYRIGHT (C) 2000. DEERE & COMPANY. MOLINE, ILLINOIS
ALL RIGHTS RESERVED
5-2 200 SERIES CUTTING PLATFORMS PC1558 (31-MAY-00)
PN=2
A12
200 SERIES CUTTING PLATFORMS
IMPORTANT
THIS PARTS CATALOG CONTAINS COMPLETE PARTS INFORMATION ON THE 200 SERIES CUTTING
PLATFORM. VINTAGE IS DETERMINED BY SERIAL NUMBERS UNDER WHICH PLATFORMS WERE MANUFACTURED.
IT IS IMPORTANT THAT THE CORRECT SERIAL NUMBER BE USED WHEN ORDERING PARTS.
DIRECTION ARROW
ARROWS ARE USED WITH ILLUSTRATIONS TO INDICATE THE FRONT OF THE UNIT. "RIGHT-HAND" AND "LEFTHAND" SIDES ARE DETERMINED BY FACING IN THE DIRECTION OF MACHINE FORWARD TRAVEL.
BOX-ENCLOSED ILLUSTRATIONS
A KEY NUMBER, SHOWN IN THE PARTS LIST, IS ASSIGNED TO A BOX ENCLOSING ALL PARTS SOLD AS A
SERVICE ASSEMBLY. A BOX NOT KEYED INCLUDES NON-CURRENT PARTS.
KITS
KIT INFORMATION WILL BE FOUND IMMEDIATLEY FOLLOWING THE STORY IN WHICH IT IS USED.
THE ILLUSTRATION IS REPEATED WITH ONLY THE KIT PARTS CALLED OUT AND WITH ALL OTHER
PARTS SHOWN IN PHANTOM FOR RELATIONSHIP.
JDM REMANUFACTURED COMPONENTS
THE SERVICE PARTS LISTED IN THIS CATALOG ARE INTENDED FOR THE REPAIR OF ORIGINAL
EQUIPMENT COMPONENTS. ALTHOUGH MOST SERVICE PARTS MAY BE USED TO REPAIR REMANUFACTURED
COMPONENTS, THE REMANUFACTURED DESIGN MAY CHANGE PARTS SUFFICIENTLY SO THAT SERVICE
PARTS ARE INADEQUATE OR NOT USABLE.
BOLT AND CAP SCREW STRENGTH IDENTIFICATION
BOLTS AND CAP SCREWS REQUIRED TO HAVE HIGH-STRENGTH QUALITIES EQUIVALENT TO SAE GRADE 8 ARE
IDENTIFIED THROUGHOUT THIS CATALOG BY THE DESCRIPTION HS SAE 8. ALL STANDARD BOLTS AND CAP
SCREWS ARE SAE GRADE 5 OR LOWER.
SI UNITS OF MEASURE
METRIC DIMENSIONS ARE GIVEN, WHERE APPLICABLE, THROUGHOUT THIS PARTS CATALOG.
TRADEMARKS
THROUGHOUT THIS PARTS CATALOG, YOU WILL FIND THE FOLLOWING DEERE & COMPANY TRADEMARKS:
DIAL-A-MATIC™
CHANGE INDICATOR LINE
(MICROFICHE CATALOGS ONLY)
CHANGES AFFECTING THE ORDERING OF PARTS ARE IDENTIFIED BY VERTICAL LINES MARKED IN THE LEFTHAND MARGIN OF REVISED PARTS LISTING IMAGES. A LINE IS ALSO AT THE LEFT-HAND EDGE OF THE
SAME PART NUMBER IN THE NUMERICAL INDEX TO SHOW THE LOCATION OF REVISED INFORMATION.
200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99) 5-3
PN=3
A13
200 SERIES CUTTING PLATFORMS
SECTION INDEX
SECTION 05 - GENERAL INFORMATION
SECTION 10 - REEL
SECTION 15 - FRAME, SHEETS, DIVIDERS, SKID PLATES AND HEADER HEIGHT CONTROL
SECTION 20 - KNIFE, CUTTERBAR AND DRIVES
SECTION 25 - AUGER AND DRIVE
SECTION 30 - HYDRAULICS
SECTION 35 - IDLERS, TIGHTENERS, AND SHIELDS
SECTION 40 - BELTS, CHAINS, SHEAVES, SPROCKETS AND DECALS
SECTION 45 - NUMERICAL INDEX
5-4 200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99)
PN=4
A14
200 SERIES CUTTING PLATFORMS
ALPHABETICAL INDEX
GRID PAGE GRID PAGE
A I8 CROSS AUGER SPROCKET .......................................... 25
I8 CROSS AUGER SUPPORT ............................................ 25 - 7
F11 ARM, BAT REEL .............................................................. 10 - 10 H16 CUTTERBAR DRIVE ........................................................ 20 - 16
F13 ARM, BAT REEL .............................................................. 10 - 12 H18 CUTTERBAR DRIVE (SH)................................................ 20 - 18
F4 ARM, PICKUP REEL ........................................................ 10 - 2 H22 CUTTERBAR DRIVE SUPPORT SPRING ...................... 20 - 22
F17 ARM, REEL ...................................................................... 10 - 16 H9 CUTTERBAR KNIFE GUARDS (NON-CLOG) ................ 20 - 9
F19 ARM, REEL ...................................................................... 10 - 18 F19 CYLINDER ROD EXTENSION ........................................ 10 - 18
F18 ARM, REEL (RIGID AND FLEXIBLE) .............................. 10 - 17 I19 CYLINDER, HYDRAULIC, LIFT REEL, MASTER............ 30 - 3
G16 ARM, STOP ...................................................................... 15 - 23 I18 CYLINDER, HYDRAULIC, LIFT REEL, SLAVE .............. 30 - 1
I4 AUGER AND SHAFT, CROSS ........................................ 25 - 3
G17 AUTOMATIC HEADER HEIGHT CONTROL .................. 15 - 24
D
- 7
B H18 DECAL, DRIVE SHAFT(SH) ............................................ 20
I13 DECAL, DRIVESHAFT...................................................... 25 - 12
G19 BALL, INDICATOR, AUTO. HEIGHT CONTROL ............ 15 - 26 I15 DECAL, DRIVESHAFT...................................................... 25 - 14
F11 BAT REEL ARM................................................................ 10 - 10 G19 DECAL, RANGE INDICATOR .......................................... 15 - 26
F13 BAT REEL ARM................................................................ 10 - 12 G22 DECAL,RANGE IND.,DIAL-A-MATIC HDR. HGT.
F11 BAT REEL DRIVE SHAFT................................................ 10 - 10 CONT. .......................................................................... 15 - 29
F13 BAT REEL DRIVE SHAFT................................................ 10 - 12 J17 DECALS ............................................................................ 40 - 3
F15 BAT REEL DRIVE SHAFT,SPRKTS,AND MTGS. .......... 10 - 14 J19 DECALS, RIGHT-HAND AND LEFT-HAND .................... 40 - 5
F11 BAT REEL MOUNTING .................................................... 10 - 10 G24 DIAL-A-MATIC HDR HGT CONT,WIRING HARNESS
F13 BAT REEL MOUNTING .................................................... 10 - 12 (FLEX) .......................................................................... 15 - 31
F11 BAT REEL SHIELD .......................................................... 10 - 10 G18 DIAL-A-MATIC HDR.HGT.CONT.SENSING BOX............ 15 - 25
F13 BAT REEL SHIELD .......................................................... 10 - 12 G18 DIAL-A-MATIC HEADER HEIGHT CONTROL MTG. ...... 15 - 25
F11 BAT REEL SLAT .............................................................. 10 - 10 G10 DIVIDER POINTS (RIGID)................................................ 15 - 17
F13 BAT REEL SLAT .............................................................. 10 - 12 G10 DIVIDER, LOOP................................................................ 15 - 17
F11 BAT REEL SPROCKETS.................................................. 10 - 10 G11 DIVIDERS, LONG, ROW CROP ...................................... 15 - 18
F13 BAT REEL SPROCKETS.................................................. 10 - 12 J15 DRIVE BELT, L.H. SIDE .................................................. 40 - 1
F4 BAT, PICKUP REEL ........................................................ 10 - 2 J16 DRIVE CHAINS AND SPROCKETS, R.H. SIDE ............ 40 - 2
F4 BATSHAFT, PICKUP REEL.............................................. 10 - 2 H18 DRIVE SHAFT DECAL (SH) ............................................ 20 - 18
I6 BEARINGS, CROSS AUGER .......................................... 25 - 5 F11 DRIVE SHAFT, BAT REEL .............................................. 10 - 10
H12 BEARINGS, KNIFE DRIVE CASE.................................... 20 - 12 F13 DRIVE SHAFT, BAT REEL .............................................. 10 - 12
J15 BELT, DRIVE, L.H. SIDE.................................................. 40 - 1 I13 DRIVE SHAFT, DECAL .................................................... 25 - 12
H3 BLOCK, GUARD AND KNIFE REPAIR............................ 20 - 2 I15 DRIVE SHAFT, DECAL .................................................... 25 - 14
H6 BOLTED KNIFE AND MOUNTINGS ................................ 20 - 6 H20 DRIVE SHAFT, HEADER - SIDEHILL ............................ 20 - 20
I8 BRACKETS, CROSS AUGER .......................................... 25 - 7 J15 DRIVE SHEAVES, L.H. SIDE .......................................... 40 - 1
J15 DRIVE TIGHTENERS, L.H. SIDE .................................... 40 - 1
J16 DRIVE TIGHTENERS, R.H. SIDE .................................... 40 - 2
C H16 DRIVE, CUTTERBAR........................................................ 20
H22 DRIVE, CUTTERBAR........................................................ 20 - 22
H10 CASE, KNIFE DRIVE........................................................ 20 - 10 H18 DRIVE, CUTTERBAR (SH) .............................................. 20 - 18
F19 CHAIN, CYL. ROD EXTENSION...................................... 10 - 18
J16 CHAINS, DRIVE, R.H. SIDE ............................................ 40 - 2
G18 CIRCUIT BOARD,DIAL-A-MATIC HDR.HGT.CONT. ...... 15 - 25 E
I13 CLUTCH, CROSS AUGER DRIVE (SH).......................... 25 - 12
I15 CLUTCH, CROSS AUGER DRIVE (SH).......................... 25 - 14 F19 EXTENSION CYL. ROD .................................................. 10 - 18
I9 CLUTCH, SLIP, CROSS AUGER DRIVE ........................ 25 - 8 F18 EXTENSION, RAM............................................................ 10 - 17
I11 CLUTCH, SLIP, CROSS AUGER DRIVE ........................ 25 - 10 I2 EXTENSIONS, FLIGHT, CROSS AUGER ...................... 25 - 1
I22 CONNECTORS, REEL DRIVE ........................................ 30 - 6
I22 CONNECTORS, REEL LIFT ............................................ 30 - 6
I4 COVER, CROSS AUGER ................................................ 25 - 3 F
I6 CRANK, CROSS AUGER ................................................ 25 - 5
I4 CROSS AUGER AND SHAFT.......................................... 25 - 3 G1 FEED PLATES, MAIN SILL, AND SUPPORTS .............. 15 - 8
I6 CROSS AUGER BEARINGS ............................................ 25 - 5 F4 FINGER, PICKUP REEL .................................................. 10 - 2
I8 CROSS AUGER BRACKETS .......................................... 25 - 7 I6 FINGERS, CROSS AUGER.............................................. 25 - 5
I4 CROSS AUGER COVER.................................................. 25 - 3 F22 FLEXIBLE FRAME ............................................................ 15 - 3
I6 CROSS AUGER CRANK .................................................. 25 - 5 F24 FLEXIBLE FRAME ............................................................ 15 - 5
I9 CROSS AUGER DRIVE.................................................... 25 - 8 G15 FLEXIBLE STABILIZER .................................................... 15 - 22
I11 CROSS AUGER DRIVE.................................................... 25 - 10 I2 FLIGHT EXTENSIONS...................................................... 25 - 1
I13 CROSS AUGER DRIVE (SH) .......................................... 25 - 12 F25 FLOOR STRIPPER .......................................................... 15 - 7
I15 CROSS AUGER DRIVE (SH) .......................................... 25 - 14 F21 FRAME .............................................................................. 15 - 2
I6 CROSS AUGER FINGERS .............................................. 25 - 5 F23 FRAME .............................................................................. 15 - 4
I2 CROSS AUGER FLIGHT EXTENSIONS ........................ 25 - 1 F22 FRAME (FLEXIBLE).......................................................... 15 - 3
I4 CROSS AUGER HUB ...................................................... 25 - 3 F24 FRAME (FLEXIBLE).......................................................... 15 - 5
I6 CROSS AUGER SHAFTS ................................................ 25 - 5 F21 FRAME (RIGID AND FLEXIBLE) .................................... 15 - 2
I8 CROSS AUGER SHIELDS .............................................. 25 - 7 F23 FRAME (RIGID AND FLEXIBLE) .................................... 15 - 4
200 SERIES CUTTING PLATFORMS PC1558 (31-MAY-00) 5-5
- 18
- 16
PN=5
A15
200 SERIES CUTTING PLATFORMS
ALPHABETICAL INDEX - CONTINUED
GRID PAGE GRID PAGE
F22 FRAME (RIGID) ................................................................ 15 - 3 G16 LINK, PUSH, STOP ARM ................................................ 15 - 23
F24 FRAME (RIGID) ................................................................ 15 - 5 G19 LINKAGE, HEIGHT SENSING.......................................... 15 - 26
G M
H3 GUARD AND KNIFE REPAIR BLOCK ............................ 20 - 2 G1 MAIN SILL, FEED PLATES, AND SUPPORTS .............. 15 - 8
F7 GUARD, PICKUP REEL .................................................. 10 - 6 J10 MOTOR, HYD., HYDROSTATIC DRIVE REEL .............. 30 - 17
F9 GUARD, PICKUP REEL .................................................. 10 - 8 J11 MOTOR, REEL.................................................................. 30 - 18
H8 GUARDS AND WEAR PLATES ...................................... 20 - 8 G17 MOUNTING, AUTO. HEADER HEIGHT CONTROL........ 15 - 24
H9 GUARDS, CUTTERBAR KNIFE (NON-CLOG) ................ 20 - 9 F11 MOUNTING, BAT REEL .................................................. 10 - 10
H2 GUARDS, LIFTING .......................................................... 20 - 1 F13 MOUNTING, BAT REEL .................................................. 10 - 12
H22 MOUNTING, CUTTERBAR DRIVE .................................. 20 - 22
G11 MOUNTING, ROW CROP DIVIDERS.............................. 15 - 18
H F15 MOUNTINGS, BAT REEL DRIVE .................................... 10
G23 HARNESS, WIRING, AUTO. HEIGHT CONTROL .......... 15 - 30
H20 HEADER DRIVE SHAFT - SIDEHILL .............................. 20 - 20 N
G18 HEADER HEIGHT CONTROL, DIAL-A-MATIC................ 15 - 25
J8 HOSE, HYDRAULIC DRIVE REEL .................................. 30 - 15 G10 NOSE, LOOP DIVIDER .................................................... 15 - 17
J9 HOSES, HYDRAULIC, PICKUP REEL ............................ 30 - 16
I22 HOSES, REEL DRIVE ...................................................... 30 - 6
I22 HOSES, REEL LIFT.......................................................... 30 - 6 O
J5 HOSES, REEL LIFT.......................................................... 30 - 12
I4 HUB, CROSS AUGER ...................................................... 25 - 3 J1 OIL LINES, HYDRAULIC LIFT REEL .............................. 30 - 8
I19 HYDRAULIC CYLINDER, LIFT REEL, MASTER ............ 30 - 3 J3 OIL LINES, HYDRAULIC LIFT REEL .............................. 30 - 10
I18 HYDRAULIC CYLINDER, LIFT REEL, SLAVE ................ 30 - 1 J5 OIL LINES, REEL LIFT .................................................... 30 - 12
J8 HYDRAULIC DRIVE REEL HOSE .................................. 30 - 15
J9 HYDRAULIC DRIVE REEL HOSES, PICKUP REEL ...... 30 - 16
I20 HYDRAULIC DRIVE REEL LINES .................................. 30 - 4 P
I23 HYDRAULIC DRIVE REEL LINES .................................. 30 - 7
J7 HYDRAULIC DRIVE REEL LINES, BAT REEL .............. 30 - 14 F3 PICKUP REEL .................................................................. 10 - 1
J7 HYDRAULIC HOSES, BAT REEL .................................... 30 - 14 F4 PICKUP REEL .................................................................. 10 - 2
I19 HYDRAULIC LIFT REEL MASTER CYLINDER .............. 30 - 3 F3 PICKUP REEL ARM ........................................................ 10 - 1
J1 HYDRAULIC LIFT REEL OIL LINES................................ 30 - 8 F4 PICKUP REEL ARM ........................................................ 10 - 2
J3 HYDRAULIC LIFT REEL OIL LINES................................ 30 - 10 F5 PICKUP REEL ARM ........................................................ 10 - 3
I18 HYDRAULIC LIFT REEL SLAVE CYLINDER .................. 30 - 1 F3 PICKUP REEL BAT .......................................................... 10 - 1
J10 HYDRAULIC MOTOR, HYDROSTATIC DRIVE REEL .... 30 - 17 F4 PICKUP REEL BAT .......................................................... 10 - 2
J10 HYDROSTATIC DRIVE REEL HYDRAULIC MOTOR .... 30 - 17 F3 PICKUP REEL BATSHAFT .............................................. 10 - 1
F4 PICKUP REEL BATSHAFT .............................................. 10 - 2
F7 PICKUP REEL DRIVE SHAFT ........................................ 10 - 6
I F9 PICKUP REEL DRIVE SHAFT ........................................ 10
F6 PICKUP REEL ECCENTRIC SPIDER.............................. 10 - 5
H21 IDLER, KNIFE DRIVE ...................................................... 20 - 21 F3 PICKUP REEL FINGER.................................................... 10 - 1
G22 IND.,RANGE,DIAL-A-MATIC HDR. HGT. CONT. ............ 15 - 29 F4 PICKUP REEL FINGER.................................................... 10 - 2
G19 INDICATOR, RANGE, AUTO. HEIGHT CONTROL ........ 15 - 26 F5 PICKUP REEL FINGER.................................................... 10 - 3
F7 PICKUP REEL GUARD .................................................... 10 - 6
F9 PICKUP REEL GUARD .................................................... 10 - 8
K F7 PICKUP REEL MOUNTINGS .......................................... 10
F9 PICKUP REEL MOUNTINGS .......................................... 10 - 8
H3 KNIFE AND GUARD REPAIR BLOCK ............................ 20 - 2 F5 PICKUP REEL SPIDER .................................................... 10 - 3
H6 KNIFE AND MOUNTINGS, BOLTED .............................. 20 - 6 F3 PICKUP REEL SPIDER PLATE ...................................... 10 - 1
H4 KNIFE AND MOUNTINGS, RIVETED .............................. 20 - 4 F4 PICKUP REEL SPIDER PLATE ...................................... 10 - 2
H10 KNIFE DRIVE CASE ........................................................ 20 - 10 F7 PICKUP REEL SPROCKETS .......................................... 10 - 6
H12 KNIFE DRIVE CASE BEARINGS AND SUPPORTS ...... 20 - 12 F9 PICKUP REEL SPROCKETS .......................................... 10 - 8
H21 KNIFE DRIVE IDLER AND TIGHTENER ........................ 20 - 21 F19 PIN, REEL ARM................................................................ 10 - 18
H9 KNIFE GUARDS, CUTTERBAR (NON-CLOG) ................ 20 - 9 G10 PLATE, DIVIDER POINT SKID ........................................ 15 - 17
F4 PLATE, PICKUP REEL SPIDER ...................................... 10 - 2
G5 PLATES, PROTECTION (RIGID) .................................... 15 - 12
L G5 PLATES, SKID (RIGID) .................................................... 15
G10 POINTS, DIVIDER (RIGID) .............................................. 15 - 17
H2 LIFTING GUARDS ............................................................ 20 - 1 G5 PROTECTION PLATES (RIGID) ...................................... 15 - 12
I23 LINES, HYDRAULIC DRIVE REEL .................................. 30 - 7
J7 LINES, HYDRAULIC, BAT REEL .................................... 30 - 14
J1 LINES, OIL, HYDRAULIC LIFT REEL.............................. 30 - 8 R
J3 LINES, OIL, HYDRAULIC LIFT REEL.............................. 30 - 10
I20 LINES, REEL, HYDRAULIC DRIVE ................................ 30 - 4 F17 REEL ARM ........................................................................ 10 - 16
5-6 200 SERIES CUTTING PLATFORMS PC1558 (31-MAY-00)
- 14
- 8
- 6
- 12
PN=6
A16
200 SERIES CUTTING PLATFORMS
ALPHABETICAL INDEX - CONTINUED
GRID PAGE GRID PAGE
F18 REEL ARM (RIGID AND FLEXIBLE) .............................. 10 - 17 F25 STRIPPER, FLOOR .......................................................... 15 - 7
F19 REEL ARM (RIGID AND FLEXIBLE) .............................. 10 - 18 I8 SUPPORT, CROSS AUGER ............................................ 25 - 7
J5 REEL LIFT OIL LINES...................................................... 30 - 12 H12 SUPPORTS, KNIFE DRIVE CASE .................................. 20 - 12
I20 REEL LINES, HYDRAULIC DRIVE .................................. 30 - 4 G1 SUPPORTS, MAIN SILL, AND FEED PLATES .............. 15 - 8
J11 REEL MOTOR .................................................................. 30 - 18 G17 SWITCHES, MOUNTING, AUTO. HEIGHT CONTROL .. 15 - 24
F4 REEL, PICKUP.................................................................. 10 - 2 G17 SWITCHES, SENSING, AUTO. HEIGHT CONTROL...... 15 - 24
G16 REINFORCEMENT, STOP ARM...................................... 15 - 23
F22 RIGID FRAME .................................................................. 15 - 3
F24 RIGID FRAME .................................................................. 15 - 5 T
H4 RIVETED KNIFE AND MOUNTINGS .............................. 20 - 4
G11 ROW CROP LONG DIVIDERS ........................................ 15 - 18 H21 TIGHTENER, KNIFE DRIVE ............................................ 20 - 21
J15 TIGHTENERS AND SHEAVE ON L.H. SIDE .................. 40 - 1
J16 TIGHTENERS AND SPROCKETS, R.H. SIDE................ 40 - 2
S
G3 SEALS .............................................................................. 15 - 10 W
G17 SENSING SWITCHES, AUTO. HDR. HGT. CONT. ........ 15 - 24
I4 SHAFT AND AUGER, CROSS ........................................ 25 - 3 H8 WEAR PLATES ................................................................ 20 - 8
F15 SHAFT, BAT REEL DRIVE .............................................. 10 - 14 G23 WIRING HARNESS-AUTO. HDR. HEIGHT CONTROL .. 15 - 30
I9 SHAFT, CROSS AUGER DRIVE .................................... 25 - 8 G24 WIRING HARNESS,DIAL-A-MATIC HDR HGT CONT .... 15 - 31
I11 SHAFT, CROSS AUGER DRIVE .................................... 25 - 10
I13 SHAFT, CROSS AUGER DRIVE (SH) ............................ 25 - 12
I15 SHAFT, CROSS AUGER DRIVE (SH) ............................ 25 - 14
H16 SHAFT, CUTTERBAR DRIVE .......................................... 20 - 16
H20 SHAFT, HEADER DRIVE - SIDEHILL ............................ 20 - 20
I6 SHAFTS, CROSS AUGER .............................................. 25 - 5
H18 SHEAVE, CUTTERBAR DRIVE (SH) .............................. 20 - 18
H21 SHEAVE, IDLER, KNIFE DRIVE ...................................... 20 - 21
J13 SHIELD .............................................................................. 35 - 1
F11 SHIELD, BAT REEL.......................................................... 10 - 10
F13 SHIELD, BAT REEL.......................................................... 10 - 12
I9 SHIELD, CROSS AUGER DRIVE .................................... 25 - 8
I11 SHIELD, CROSS AUGER DRIVE .................................... 25 - 10
I13 SHIELD, CROSS AUGER DRIVE (SH) .......................... 25 - 12
I15 SHIELD, CROSS AUGER DRIVE (SH) .......................... 25 - 14
H16 SHIELD, CUTTERBAR DRIVE ........................................ 20 - 16
H18 SHIELD, CUTTERBAR DRIVE (SH) ................................ 20 - 18
I8 SHIELDS, CROSS AUGER .............................................. 25 - 7
J13 SHIELDS, DRIVE .............................................................. 35 - 1
G10 SHOE, DIVIDER................................................................ 15 - 17
G8 SHOES, SKID (FLEXIBLE) .............................................. 15 - 15
H20 SIDEHILL - HEADER DRIVE SHAFT .............................. 20 - 20
G5 SKID PLATES (RIGID)...................................................... 15 - 12
G8 SKID SHOES (FLEXIBLE) ................................................ 15 - 15
F11 SLAT, BAT REEL.............................................................. 10 - 10
F13 SLAT, BAT REEL.............................................................. 10 - 12
F6 SPIDER, ECCENTRIC, PICKUP REEL............................ 10 - 5
H22 SPRING, CUTTERBAR DRIVE ........................................ 20 - 22
H23 SPRING, STABILIZER ...................................................... 20 - 23
H24 SPRING, STABILIZER ...................................................... 20 - 24
I8 SPROCKET, CROSS AUGER.......................................... 25 - 7
I9 SPROCKET, CROSS AUGER DRIVE ............................ 25 - 8
I11 SPROCKET, CROSS AUGER DRIVE ............................ 25 - 10
I13 SPROCKET, CROSS AUGER DRIVE (SH) .................... 25 - 12
I15 SPROCKET, CROSS AUGER DRIVE (SH) .................... 25 - 14
H16 SPROCKET, CUTTERBAR DRIVE .................................. 20 - 16
F11 SPROCKETS, BAT REEL ................................................ 10 - 10
F13 SPROCKETS, BAT REEL ................................................ 10 - 12
F15 SPROCKETS, BAT REEL DRIVE .................................... 10 - 14
F7 SPROCKETS, PICKUP REEL .......................................... 10 - 6
F9 SPROCKETS, PICKUP REEL .......................................... 10 - 8
G15 STABILIZER (FLEXIBLE).................................................. 15 - 22
G15 STABILIZER ARM ............................................................ 15 - 22
H23 STABILIZER SPRING ...................................................... 20 - 23
H24 STABILIZER SPRING ...................................................... 20 - 24
G16 STOP ARM, PUSH LINK, AND REINFORCEMENT ...... 15 - 23
F19 STOP, CYL. ROD EXTENSION ...................................... 10 - 18
200 SERIES CUTTING PLATFORMS PC1558 (31-MAY-00) 5-7
PN=7
MEMORANDA
200 - SERIES
5-8 200 SERIES CUTTING PLATFORMS PC1558 (27-OCT-81)
PN=8
H26615 -UN-01JAN94
F3
REEL
PICKUP REEL-YELLOW (RIGID AND FLEXIBLE)
(SERIAL NO. -365600)
a
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
1 AH19680 SHAFT 6 (SUB AH97182) (213)
AH63039 SHAFT 6 (215) (SUB AH97183)
AH19695 SHAFT 6 (SUB AH97184) (216)
AH19698 SHAFT 6 (218) (SUB AH97185)
AH63604 SHAFT 6 (SUB AH97186) (220)
AH80100 SHAFT 6 (222) (SUB AH97187)
AH81254 SHAFT 6 (224) (SUB AH87188)
2 03H1810 BOLT AR 1/4" X 1-1/2"
E45229 LOCK NUT AR
3 H33316 FINGER AR (213-186 USED; 215-216 USED; 216-234 USED;
218-258 USED; 220-294 USED; 222-324 USED;
AND 224-360 USED)
4 H33317 CLIP AR (213-186 USED; 215-216 USED; 216-234 USED;
218-258 USED; 220-294 USED; 222-324 USED;
AND 224-360 USED)
5 H33318 RIVET AR (213-186 USED; 215-216 USED; 216-234 USED;
218-258 USED; 220-294 USED; 222-324 USED;
AND 224-360 USED)
6 AH19681 SLAT 12 (R.H. AND L.H.)(213) (SUB AH97190)
AH19682 SLAT 6 (CENTER)(213) (SUB AH97191)
AH63038 SLAT 18 (215) (SUB AH97193)
AH19696 SLAT AR (216-18 USED; 218-6 USED) (SUB AH97194)
AH19699 SLAT AR (218, R.H. AND L.H.-2 USED; 220, CENTER- 6
USED) (SUB AH97195)
AH65216 SLAT 12 (220) (SUB AH97196)
AH80098 SLAT 18 (222) (SUB AH97197)
AH81256 SLAT 18 (224) (SUB AH97200)
7 E40203 U-BOLT 24
8 E40202 LOCK NUT 48 -365600 (SUB E45229)
E45229 LOCK NUT 48
9 E40205 CAP 24
10 E40206 BASE 24
11 AE24410 ARM 24
12 19H2020 CAP SCREW 72 5/16" X 1/2"
12H303 LOCK WASHER 72 5/16"
14H785 NUT 72 5/16"
13 H84031 PLATE 4 (213, 215, 216, 218)
H84031 PLATE 4 -267450 (220)
H88454 PLATE 4 267451- (SUB H98689) (220)
H88454 PLATE 4 (SUB H98689) (222 AND 224)
200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99) 10-1
PN=9
H26615 -UN-01JAN94
F4
REEL
PICKUP REEL-BLACK (RIGID AND FLEXIBLE)
(SERIAL NO. 365601- )
a
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
1 AH97182 SHAFT 6 (213)
AH97183 SHAFT 6 (215)
AH97184 SHAFT 6 (216)
AH97185 SHAFT 6 (218)
AH97186 SHAFT 6 (220)
AH97187 SHAFT 6 (222)
AH97188 SHAFT 6 (224)
AH97189 SHAFT 6 433738- (230)
2 03H1810 BOLT AR 1/4" X 1-1/2"
E45229 LOCK NUT AR
3 H33316 FINGER AR (213-186 USED; 215-216 USED; 216-234 USED;
218-258 USED; 220-294 USED; 222-324 USED;
224-360 USED; AND 230-456 USED)
4 H33317 CLIP AR (213-186 USED; 215-216 USED; 216-234 USED;
218-258 USED; 220-294 USED; 222-324 USED;
224-360 USED; AND 230-456 USED)
5 H33318 RIVET AR (213-186 USED; 215-216 USED; 216-234 USED;
218-258 USED; 220-294 USED; 222-324 USED;
224-360 USED; AND 230-456 USED)
6 AH97190 SLAT 12 R.H AND L.H. (213)
AH97191 SLAT 6 CENTER (213)
AH97193 SLAT 18 (215)
AH97194 SLAT AR (216-18 USED AND 218 CENTER-6 USED)
AH97195 SLAT AR (218, R.H. AND L.H.-12 USED; 220, CENTER-6
USED)
AH97196 SLAT 12 (220)
AH97197 SLAT 18 (222)
AH97200 SLAT 18 (224)
AH97198 SHAFT 12 433738- R.H. AND L.H. (230)
AH97199 SHAFT 12 433738- CENTER (230)
7 E40203 U-BOLT AR (213, 215, 216, 218, 220, 222, 224-36 USED;
AND 230-42 USED)
8 E40202 LOCK NUT AR -585895 (SUB E45229)
E45229 LOCK NUT AR (213, 215, 216, 218, 220, 222, 224-72 USED;
AND 230-42 USED)
9 E40205 CAP AR (213, 215, 216, 218, 220, 222, 224-36 USED;
AND 230-42 USED)
10 E40206 BASE AR (213, 215, 216, 218, 220, 222, 224-36 USED;
AND 230-42 USED)
11 AH97207 ARM AR (213, 215, 218, 220, 222, 224-36 USED; AND
230-42 USED)
12 19H2020 CAP SCREW 72 5/16" X 1/2"
12H303 LOCK WASHER 72 5/16"
14H785 NUT 72 5/16"
13 H98688 PLATE 4 (213, 215, 216, AND 218)
H98689 PLATE AR (220, 222, 224-4 USED; AND 230-5 USED)
10-2 200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99)
PN=10
F5
PICKUP REEL ECCENTRIC SPIDER (RIGID AND FLEXIBLE)
H26616 -UN-01JAN94
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
(SERIAL NO. -231153)
REEL
a
1 P42337 LOCK NUT 6 (RIGID) (SUB E59584, THIS APPLICATION)
14H1040 NUT 6 1/2", (FLEXIBLE)
2 12H301 LOCK WASHER 6 1/2"
3 24H1111 WASHER 1 17/32" X 1-1/16" X 0.090", (RIGID)
24H1162 WASHER 1 17/32" X 1-1/4" X 0.060", (FLEXIBLE)
4 H33333 FINGER 6 L.H. (RIGID)
H33332 FINGER 6 R.H. (RIGID)
5 AH61937 STRAP 6 (SUB AH97221) (RIGID)
6 E40212 SPACER 6 (RIGID)
H89200 SPACER 6 (FLEXIBLE)
7 H33334 PIN 6 (RIGID) (SUB E59584 AND E59585)
19H1831 CAP SCREW 6 1/2" X 2", (FLEXIBLE)
8 AH66884 FINGER 6 L.H. (RIGID) (SUB AH97218)
AH66883 FINGER 6 R.H. (RIGID) (SUB AH97217)
9 E40203 U-BOLT 6
10 E40202 LOCK NUT 12 -231153 (SUB E45229)
E45229 LOCK NUT 12
11 E40205 CAP 6
12 E40206 BASE 6
13 AE24410 ARM 6 (SUB AH97207)
14 19H2020 CAP SCREW 12 5/16" X 1/2"
12H303 LOCK WASHER 12 5/16"
14H785 NUT 12 5/16"
15 19H1900 CAP SCREW 6 5/16" X 3/4"
12H303 LOCK WASHER 6 5/16"
14H785 NUT 6 5/16"
16 H84030 PLATE 1 (SUB H98691)
17 H64720 RING 1 (SUB H98693)
NOTE: QUANTITIES SHOWN ARE FOR ONE END ONLY.
200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99) 10-3
PN=11
MEMORANDA
REEL
10-4 200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99)
PN=12
F6
PICKUP REEL ECCENTRIC SPIDER (RIGID AND FLEXIBLE)
HP614 -UN-01JAN94
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
(SERIAL NO. 231154- )
REEL
a
1 14H1040 NUT 1 1/2", (FLEXIBLE)
2 12H301 LOCK WASHER 1 1/2", (FLEXIBLE)
3 24H1162 WASHER 1 17/32" X 1-1/4" X 0.060", (FLEXIBLE)
4 H89200 SPACER 6 (FLEXIBLE)
5 19H1831 CAP SCREW 1 1/2" X 2", (FLEXIBLE)
6 E59585 BOLT 6 (RIGID)
7 E40212 SPACER 6 (RIGID)
8 AH61937 STRAP 6 -365600 (SUB AH97221) (YELLOW) (RIGID)
AH97221 STRAP 6 365601- (BLACK) (RIGID)
9 H33332 FINGER 6 R.H. (RIGID)
H33333 FINGER 6 L.H. (RIGID)
10 E59584 FLANGE NUT 6 FLANGE (RIGID)
11 AH66883 FINGER 6 -365600 R.H. (YELLOW) (RIGID) (SUB AH97217)
AH97217 FINGER 6 R.H. (BLACK) (RIGID)
AH66884 FINGER 6 -365600 L.H. (YELLOW) (RIGID) (SUB AH97218)
AH97218 FINGER 6 L.H. (BLACK) (RIGID)
12 E40203 U-BOLT 6
13 E40202 LOCK NUT 12 -585895 (SUB E45229)
E45229 LOCK NUT 12
14 E40205 CAP 6
15 E40206 BASE 6
16 AE24410 ARM 6 -365600 (SUB AH97207) (YELLOW)
AH97207 ARM 6 365601- (BLACK)
17 H84030 PLATE 1 -365600 (YELLOW) (SUB H98691)
H98691 PLATE 1 (BLACK)
18 H64720 RING 1 -365600 (YELLOW) (SUB H98693)
H98693 RING 1 (BLACK)
19 19H2020 CAP SCREW 12 5/16" X 1/2"
12H303 LOCK WASHER 12 5/16"
14H785 NUT 12 5/16"
20 19H1900 CAP SCREW 6 5/16" X 3/4"
12H303 LOCK WASHER 6 5/16"
14H785 NUT 6 5/16"
NOTE: QUANTITIES SHOWN ARE FOR ONE END ONLY.
200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99) 10-5
PN=13
H32224F -UN-01JAN94
F7
REEL
PICKUP REEL DRIVE SHAFTS, MOUNTINGS, AND SPROCKETS
(RIGID AND FLEXIBLE)
a
10-6 200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99)
THIS PARTS LISTING IS CONTINUED
PN=14
F8
PICKUP REEL DRIVE SHAFTS, MOUNTINGS, AND SPROCKETS - CONTINUED
(RIGID AND FLEXIBLE)
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
1 C3142E SNAP RING 2
2 19H1792 CAP SCREW 2 1/2" X 1"
12H301 LOCK WASHER 2 1/2"
3 AH119100 BRACKET 1 L.H. (SUB FOR AH88967)
4 H93483 SET SCREW 2
14H821 NUT 2 5/8"
5 22H1043 SET SCREW 2 3/8" X 1/4"
6 AH89655 LOCKING COLLAR 1
7 24H1553 WASHER 5 1-5/8" X 2-1/4" X 0.194"
8 H98743 BUSHING 4 (SUB FOR E40204, THIS APPLICATION)
9 AH97283 SUPPORT 1 (SUB FOR AH88971) L.H.
10 AE24403 BALL BEARING 6
11 19H1765 CAP SCREW 6 3/8" X 1-3/4"
12H304 LOCK WASHER 6 3/8"
14H812 NUT 6 3/8"
12 03H1500 BOLT 1 3/8" X 1"
12H304 LOCK WASHER 1 3/8"
H20024 LOCK NUT 1
13 24H1305 WASHER 12 -231153 13/32" X 13/16" X 0.065"
14 AH97215 SHAFT 1 365601-620300 (SUB FOR AE24407) (BLACK) (213, 215, 216, AND
218)
AH127484 SHAFT 1 620301- (BLACK) (213, 215, 216 AND 218)
AH97216 SHAFT 1 -621250 (SUB FOR AE24407 AND AH89657) (BLACK) (220,
222, AND 224)
AH127486 SHAFT 1 621251- (BLACK) (220, 222 AND 224)
AH127488 SHAFT 1 621751- (BLACK)(230) (SUB FOR AH106100)
15 JD7759 LUBRICATION FITTING 2 STRAIGHT, 1/8"
16 AH97282 BRACKET 1 (SUB FOR AH88970 AND AH95483) R.H.
17 24H1520 WASHER 1 1-15/32" X 2" X 0.105"
18 22H853 SET SCREW 2 3/8" X 7/8"
14H732 NUT 2 3/8"
19 AH88831 CHAIN SPROCKET 1 DRIVEN, 81 TEETH
20 AH96589 BRACKET 1 -317200 REEL SHIELD
21 AH95481 SHIELD 1 (SUB FOR AH88959) DRIVE REEL
22 19H1900 CAP SCREW 2 -317200 5/16" X 3/4"
12H303 LOCK WASHER 2 -317200 5/16"
24H1136 WASHER 2 -317200 11/32" X 11/16" X 0.065"
23 22H818 SET SCREW 2 5/16" X 3/4"
14H611 NUT 2 5/16"
24 AH77367 CHAIN SPROCKET 1 20 TEETH
25 03H1731 BOLT 4 1/2" X 1-1/2"
12H301 LOCK WASHER 4 1/2"
14H1040 NUT 4 1/2"
26 03H1774 BOLT 2 -317200 5/16" X 5/8"
N10213 LOCK NUT 2 -317200
27 H87360 SHIM 1
28 26H22 SHAFT KEY 1 1/4" X 1"
29 AH119099 BRACKET 1 R.H. (SUB FOR AH88966)
30 E54809 LOCK NUT 1 FLANGE
REEL
200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99) 10-7
THIS PARTS LISTING IS CONTINUED
PN=15
H32224F -UN-01JAN94
F9
REEL
PICKUP REEL DRIVE SHAFTS, MOUNTINGS, AND SPROCKETS - CONTINUED
(RIGID AND FLEXIBLE)
a
10-8 200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99)
THIS PARTS LISTING IS CONTINUED
PN=16
F10
PICKUP REEL DRIVE SHAFTS, MOUNTINGS, AND SPROCKETS - CONTINUED
(RIGID AND FLEXIBLE)
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
31 H81277 BUSHING 1
32 24H1111 WASHER 1 17/32" X 1-1/16" X 0.090"
33 08H4654 CAP SCREW 1 1/2" X 7-1/2"
34 H89110 TRUNNION 1
35 26H46 SHAFT KEY 1 3/8" X 2-1/8"
36 AH97210 SHAFT 1 -620300 (SUB FOR AH88965) DRIVE, R.H. (BLACK) (213,
215, 216, 218 AND 220)
AH127483 SHAFT 1 620301- DRIVE, R.H. (BLACK) (213, 215, 216 AND 218)
AH127485 SHAFT 1 621251- DRIVE, R.H. (BLACK) (220, 222 AND 224) (SUB
FOR AH89656 AND AH97211)
AH127487 SHAFT 1 DRIVE, R.H. (BLACK)(230) (SUB FOR AH106101)
37 AH65197 SHAFT 1 -365600 CENTER (YELLOW) (213) (NO LONGER AVAILABLE)
AH97160 SHAFT 1 365601- CENTER (BLACK) (213)
AH97161 SHAFT 1 365601- (SUB FOR AH65199) CENTER (BLACK) (215)
AH97162 SHAFT 1 365601- (SUB FOR AH65200) CENTER (BLACK) (216)
AH97164 SHAFT 1 365601- (SUB FOR AH65204) CENTER (BLACK) (218)
AH97166 SHAFT 1 365601- CENTER (BLACK) (220) (SUB FOR AH65203 AND
AH94670)
AH97167 SHAFT 1 365601- (SUB FOR AH89659) CENTER (BLACK) (222)
AH97168 SHAFT 1 365601- (SUB FOR AH89658) CENTER (BLACK) (224)
AH97169 SHAFT 1 433738- CENTER (BLACK) (230)
38 19H1936 CAP SCREW 6 3/8" X 3/4"
12H304 LOCK WASHER 6 3/8"
H20024 LOCK NUT 6
39 .................. LINK CHAIN 1 ROLLER, DRIVE, TYPE 2050, 1-1/4" PITCH, 75
LINKS, (ASSEMBLE FROM AP19992 AND AP19991)
.. H98811 DECAL 1 (213,-620304; 215,-620484; 216,-620685;
218,-620950; 220,-621315; 222,-621450;
224,-621654; 230,-621787)
REEL
200 SERIES CUTTING PLATFORMS PC1558 (31-MAY-00) 10-9
PN=17
HP1076 -UN-01JAN94
F11
REEL
BAT REEL DRIVE SHAFT, SPROCKETS, MOUNTINGS, AND TRUSS RODS
213, 215, 216 & 218 ( - ) 220, 222 & 224 ( -365600)
a
10-10 200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99)
THIS PARTS LISTING IS CONTINUED
PN=18
F12
BAT REEL DRIVE SHAFT, SPROCKETS, MOUNTINGS, AND TRUSS RODS - CONTINUED
213, 215, 216 & 218 ( - ) 220, 222 & 224 ( -365600)
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
1 JD7759 LUBRICATION FITTING 2 STRAIGHT, 1/8"
2 34H249 SPRING PIN 2 -365600 1/8" X 7/8"
3 H87563 PIN 2 -365600 (NO LONGER AVAILABLE)
4 P35017 SPRING 2 -365600
5 24H1325 WASHER 2 -365600 15/32" X 59/64" X 0.065"
6 BP13560 BUSHING 4 -365600
M1111T BUSHING 4 365601-
7A AH88963 SUPPORT 1 -365600 (SUB AH97231, H93483 AND (2) 14H821)
7B AH97231 SUPPORT 1 L.H.
8 P43332 PISTON RING 1
9 24H1520 WASHER 4 1-15/32" X 2" X 0.105"
10 H93483 SET SCREW 2 365601-
14H821 NUT 4 365601- 5/8"
11A AH95479 SUPPORT 1 -365600 (SUB AH97296, H93483 AND (2) 14H821)
11B AH97296 BRACKET 1 R.H.
12 AH88831 CHAIN SPROCKET 1 DRIVEN, 81 TEETH
13 AH96589 BRACKET 1 -317200 REEL SHIELD
14 03H1774 BOLT 2 -317200 5/16" X 5/8"
N10213 LOCK NUT 2 -317200
15 AH88959 SHIELD 1 -317200 (SUB AH95481 AND AH96589)
AH95481 SHIELD 1 DRIVE, REEL
16 24H1136 WASHER 2 365601- 11/32" X 11/16" X 0.065"
17 19H1900 CAP SCREW 2 5/16" X 3/4"
12H303 LOCK WASHER 2 5/16"
18 22H818 SET SCREW 2 5/16" X 3/4"
14H611 NUT 2 5/16"
19 AH66504 CHAIN SPROCKET 1 DRIVE, 30 TEETH
20 22H853 SET SCREW 2 3/8" X 7/8"
21 .................. LINK CHAIN 1 TYPE 2050, 1-1/4" PITCH, 75 LINKS, (ASSEMBLE
FROM AP19992 AND AP19991)
22 03H1731 BOLT 4 1/2" X 1-1/2"
12H301 LOCK WASHER 4 1/2"
14H1040 NUT 4 1/2"
23 H87360 SHIM 1
24 26H22 SHAFT KEY 1 1/4" X 1"
25 H139078 SHIELD 5 (SUB FOR H79544) REEL END, L.H.
H139077 SHIELD 5 (SUB FOR H79545) REEL END, L.H.
26 H76944 ARM AR (213, 215, AND 216-20 USED; 218-25 USED)
H76944 ARM AR -365600 (220-25 USED; 222 AND 224-30 USED)
27 03H1527 BOLT 60 -267450 1/4" X 1-1/4"
21H1024 SCREW 60 1/4" X 5/8"
12H302 LOCK WASHER 60 1/4"
14H786 NUT 60 1/4"
28 19H1936 CAP SCREW 50 3/8" X 3/4"
12H304 LOCK WASHER 50 3/8"
14H812 NUT 50 3/8"
REEL
200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99) 10-11
THIS PARTS LISTING IS CONTINUED
PN=19
HP1076 -UN-01JAN94
F13
REEL
BAT REEL DRIVE SHAFT, SPROCKETS, MOUNTINGS, AND TRUSS RODS - CONTINUED
213, 215, 216 & 218 ( - ) 220, 222 & 224 ( -365600)
a
10-12 200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99)
THIS PARTS LISTING IS CONTINUED
PN=20
F14
BAT REEL DRIVE SHAFT, SPROCKETS, MOUNTINGS, AND TRUSS RODS - CONTINUED
213, 215, 216 & 218 ( - ) 220, 222 & 224 ( -365600)
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
29 H24049 SLAT 5 -267450 WOOD (213) (NO LONGER AVAILABLE)
H62942 SLAT 5 -267450 WOOD (215) (NO LONGER AVAILABLE)
H22819 SLAT 5 -267450 WOOD (216) (NO LONGER AVAILABLE)
H22820 SLAT 5 -267450 WOOD (218) (NO LONGER AVAILABLE)
H28027 SLAT 5 -267450 WOOD (220) (NO LONGER AVAILABLE)
H104020 SLAT 5 (SUB FOR H95226 OR H98440) METAL, BLACK (213)
E60573 SLAT 5 (SUB FOR H95227 OR H98441) METAL, BLACK (215)
E60574 SLAT 5 BLACK (216) (SUB FOR H79258)
E60574 SLAT 5 (SUB FOR H98442) METAL, BLACK (216)
E60575 SLAT 5 BLACK (218) (SUB FOR H79259)
E60575 SLAT 5 (SUB FOR H98443) METAL, BLACK (218)
H79260 SLAT 5 -365600 (SUB E60576) METAL, YELLOW (220)
H79261 SLAT 5 -365600 METAL, YELLOW (222)
H79262 SLAT 5 -365600 METAL, YELLOW (224) (SUB H104022)
30 AH89305 SHAFT 1 (213)
AH89301 SHAFT 1 (215)
AH89306 SHAFT 1 (216)
AH89307 SHAFT 1 (218)
AH89308 SHAFT 1 -365600 (220) (NO LONGER AVAILABLE)
AH89309 SHAFT 1 -365600 (222) (NO LONGER AVAILABLE)
AH89310 SHAFT 1 -365600 (224) (NO LONGER AVAILABLE)
31 26H46 SHAFT KEY 1 3/8" X 2-1/8"
32 H79255 STUD 5 (220)
H79257 STUD 5 (222)
H79252 STUD 5 (224)
33 BP12233 LOCK NUT 10 (SUB T11234)
34 24H1311 WASHER 10 13/32" X 1-1/4" X 0.220"
35 H28031 WASHER 10 RUBBER
36 H28030 STRAP AR (220-5 USED; 222 AND 224-10 USED)
37 19H1813 CAP SCREW AR 5/16" X 5/8", (220-5 USED; 222 AND 224-10
USED)
12H303 LOCK WASHER AR 5/16", (220-5 USED; 222 AND 224-10 USED)
14H785 NUT AR 5/16", (220-5 USED; 222 AND 224-10 USED)
REEL
200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99) 10-13
PN=21
H32220F -UN-01JAN94
F15
REEL
BAT REEL DRIVE SHAFT, SPROCKETS, AND MOUNTINGS
220, 222, 224 AND 230 (SERIAL NO. 365601- )
a
10-14 200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99)
PN=22
F16
BAT REEL DRIVE SHAFT, SPROCKETS, AND MOUNTINGS - CONTINUED
220, 222, 224 AND 230 (SERIAL NO. 365601- )
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
1 P43332 PISTON RING 1
2 24H1520 WASHER 4 1-15/32" X 2" X 0.105"
3 M1111T BUSHING 4
4 AH97231 SUPPORT 1 L.H.
5 H93483 SET SCREW 2
14H821 NUT 4 5/8"
6 JD7759 LUBRICATION FITTING 2 STRAIGHT, 1/8"
7 AH133746 TUBE 1 (SUB FOR AH91379) (220)
AH133747 TUBE 1 (SUB FOR AH91380) (220)
AH133748 TUBE 1 (SUB FOR AH91381) (222)
AH133749 TUBE 1 (SUB FOR AH91382) (222)
8 19H1731 CAP SCREW AR 3/8" X 1", (220-19 USED; 222 AND 224-24 USED;
230 RIGID- 29 USED)
12H304 LOCK WASHER AR 3/8", (220-19 USED; 222 AND 224-24 USED; 230
RIGID- 29 USED)
14H812 NUT AR 3/8", (220-19 USED; 222 AND 224-24 USED; 230
RIGID- 29 USED)
9 AH91383 SHAFT 1 R.H. (220, 222, AND 224)
AH91384 SHAFT 1 L.H. (220, 222, AND 224)
AH91385 SHAFT 1 R.H. (230 RIGID)
AH91386 SHAFT 1 L.H. (230 RIGID)
10 19H1732 CAP SCREW 6 3/8" X 1-1/4"
12H304 LOCK WASHER 6 3/8"
14H812 NUT 6 3/8"
11 26H46 SHAFT KEY 1 3/8" X 2-1/8"
12 AH97296 BRACKET 1 R.H.
13 AH88831 CHAIN SPROCKET 1 DRIVEN, 81 TEETH
14 AH95481 SHIELD 1
15 24H1136 WASHER 2 11/32" X 11/16" X 0.065"
16 19H1900 CAP SCREW 2 5/16" X 3/4"
12H303 LOCK WASHER 2 5/16"
17 22H818 SET SCREW 2 5/16" X 3/4"
14H611 NUT 2 5/16"
18 AH66504 CHAIN SPROCKET 1 DRIVE, 30 TEETH
19 22H853 SET SCREW 2 3/8" X 7/8"
14H732 NUT 2 3/8"
20 .................. LINK CHAIN 1 ROLLER, DRIVE, TYPE 2050, 1-1/4" PITCH, 75
LINKS, (ASSEMBLE FROM AP19992 AND AP19991)
21 03H1731 BOLT 4 1/2" X 1-1/2"
12H301 LOCK WASHER 4 1/2"
14H1040 NUT 4 1/2"
22 H87360 SHIM 1
23 26H22 SHAFT KEY 1 1/4" X 1"
24 H79544 SHIELD 5 L.H.
H79545 SHIELD 5 R.H.
25 H139076 ARM AR (SUB FOR H100243) (220-25 USED; 222 AND
224-30 USED; 230 RIGID-35 USED)
26 21H1024 SCREW AR 1/4" X 5/8", (220-5O USED; 222 AND 224-60
USED; 230 RIGID- 70 USED)
12H302 LOCK WASHER AR 1/4", (220-50 USED; 222 AND 224-60 USED; 230
RIGID-70 USED)
14H786 NUT AR 1/4", (220-50 USED; 222 AND 224-60 USED; 230
RIGID-70 USED)
14H1040 NUT 1
27 E60576 SLAT 5 (SUB FOR H98444) METAL, BLACK (220 AND 230
RIGID)
H104021 SLAT 5 (SUB FOR H98445) METAL, BLACK (222)
H104022 SLAT 5 (SUB FOR H98446) METAL, BLACK (224)
E60571 SLAT 10 (SUB FOR H98448) METAL, BLACK (230 RIGID)
REEL
200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99) 10-15
PN=23
F17
REEL ARM (RIGID AND FLEXIBLE)
H29690F -UN-01JAN94
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
1 19H1909 CAP SCREW 1 3/4" X 3-3/4", (SUB 19H2725) (R.H.)
19H2000 CAP SCREW 1 3/4" X 5", (L.H.)
12H236 LOCK WASHER 1 3/4"
14H794 NUT 1 3/4"
2 B10344 BUSHING 4
3 AH88837 ARM AR (SUB AH97295, H94005, H98698, H98494, (2)
H87048, (2) M63139 AND 11H236)
AH97295 ARM 1 L.H.
AH88836 ARM AR (SUB AH97294, H94005, H98698, H98494, (2)
H87048, (2) M63139 AND 11H236)
AH97294 ARM 1 R.H.
4 H87238 LATCH 2
5 H87048 SCREW 4 SELF-TAPPING
6 H33456 WASHER 2
7 H87065 PIN AR -365600 (1 USED-L.H.; 2 USED-R.H.) (SUB M48519)
M87968 PIN 1 (SUB FOR M48519)
8 11H216 COTTER PIN 4 3/16" X 1"
9 H87239 RETAINER 2
10 H87236 STOP 1 L.H. (NO LONGER AVAILABLE)
H87237 STOP 1 R.H.
11 19H1734 CAP SCREW 2 5/8" X 2"
12H294 LOCK WASHER 2 5/8"
14H1039 NUT 2 5/8"
12 H87066 PIN 1 (SUB H98765)
H98765 PIN 1 DRILLED (L.H.)
13 24H1368 WASHER 4 21/32" X 1-5/16" X 0.090"
(SERIAL NO. -365600)
REEL
c
10-16 200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99)
PN=24
HP1287 -UN-01JAN94
F18
REEL
REEL ARM (RIGID AND FLEXIBLE)
(SERIAL NO. 365601-530050)
c
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
1 19H1909 CAP SCREW 1 3/4" X 3-3/4", (SUB 19H2725)
19H2000 CAP SCREW 1 3/4" X 5"
12H236 LOCK WASHER 1 3/4"
14H794 NUT 1 3/4"
2 M63139 BUSHING 4
3 24H1368 WASHER 4 21/32" X 1-5/16" X 0.090"
4 19H1734 CAP SCREW 2 5/8" X 2"
12H294 LOCK WASHER 2 5/8"
14H1039 NUT 2 5/8"
5 11H236 COTTER PIN 2 1/8" X 1"
6 H98765 PIN 1 (213, 215, 216, 218, 220, 222, AND 224; L.H.
BOTTOM)
H98494 PIN 1 (230 RIGID-L.H. BOTTOM)
M87968 PIN 1 (R.H. BOTTOM) (SUB FOR M48519)
7 H94005 STOP 2
8 H87239 RETAINER 2
9 H98494 PIN 2 (TOP)
10 H87048 SCREW 4 SELF-TAPPING
11 H98698 LATCH 2
12 AH97229 ARM 1 (SUB AH97295)
AH97295 ARM 1 L.H.
AH97228 ARM 1 (SUB AH97294)
AH97294 ARM 1 R.H.
200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99) 10-17
PN=25
HP1288 -UN-01JAN94
F19
REEL
REEL ARM (RIGID AND FLEXIBLE)
(SERIAL NO. 530051- )
c
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
1 19H1909 CAP SCREW 1 3/4" X 3-3/4", R.H. (SUB 19H2725)
19H2000 CAP SCREW 1 3/4" X 5", L.H.
12H236 LOCK WASHER 2 3/4"
14H794 NUT 2 3/4"
2 M63139 BUSHING 4
3 24H1368 WASHER 4 21/32" X 1-5/16" X 0.090"
4 19H1734 CAP SCREW 2 5/8" X 2"
12H294 LOCK WASHER 2 5/8"
14H1039 NUT 2 5/8"
5 11H236 COTTER PIN 4 1/8" X 1"
6 H98765 PIN 2 (TOP)
7 H105501 EXTENSION 2
8 H25099 SNAP RING 2
9 H105498 NUT 2
10 H105499 RING 2 -600025 (SUB H118628)
H118628 RING 2
11 AH104396 STOP 2
12 H109147 PIN 1 R.H. BOTTOM
H109146 PIN 1 L.H. BOTTOM (213, 215, 216, 218, 220, 222 AND
224)
H98494 PIN 1 L.H. BOTTOM (230)
13 AH104090 LINK CHAIN 2
14 H76139 SCREW 2
15 H87239 RETAINER 2
16 AH108562 ARM 1 L.H.
AH108561 ARM 1 R.H.
10-18 200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99)
PN=26
FRAME, SHEETS, DIVIDERS, SKID PLATES, AND HEADER HEIGHT CONTROL
MEMORANDA
200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99) 15-1
PN=27
HP3240 -UN-01JAN94
F21
FRAME, SHEETS, DIVIDERS, SKID PLATES, AND HEADER HEIGHT CONTROL
FRAME (RIGID AND FLEXIBLE)
g
15-2 200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99)
THIS PARTS LISTING IS CONTINUED
PN=28
F22
FRAME, SHEETS, DIVIDERS, SKID PLATES, AND HEADER HEIGHT CONTROL
FRAME (RIGID AND FLEXIBLE) - CONTINUED
KEY PART NO. PART NAME QTY SERIAL NO. REMARKS
1 AH88947 FRAME 1 -229674 (SUB AH94969)
AH94969 FRAME AR -317200 (SUB AH96079, AH97127, AH97129 AND (3)
AH95990)
AH96079 FRAME 1 -365600 (SUB AH98907)
AH98907 FRAME 1 -530050 (SUB AH103379, H109146 AND H109147)
AH103379 FRAME 1 -600000 (SUB AH111253)
AH111253 FRAME 1 (213)
AH88948 FRAME 1 -229674 (SUB AH90626, AH90627, AH90628, AH90631, (3)
AH95991, AH96080 AND AH97127) (215) (NO
LONGER AVAILABLE)
AH94970 FRAME AR -317200 (SUB AH96080, AH97127, AH97129 AND (3)
AH95991)
AH96080 FRAME 1 -365600 (SUB AH98908)
AH98908 FRAME 1 -530050 (SUB AH103380, H109146 AND H109147)
AH103380 FRAME 1 -600000 (SUB AH111254)
AH111254 FRAME 1 (215)
AH88951 FRAME 1 -229674 (SUB AH94971)
AH94971 FRAME AR -317200 (SUB AH96338, AH97127, AH97129 AND (3)
AH95992)
AH96338 FRAME 1 -365600 (SUB AH98909)
AH98909 FRAME 1 -530050 (SUB AH103381, H109146 AND H109147)
AH103381 FRAME 1 -600000 (216) (SUB AH111255)
AH111255 FRAME 1 (216)
AH88952 FRAME 1 -268385 (SUB AH94972)
AH94972 FRAME AR -317200 (SUB AH95915, AH97127, AH97129 AND (3)
AH95993)
AH95915 FRAME 1 -365600 (SUB AH98910)
AH98910 FRAME 1 -530050 (SUB AH105135, H109146 AND H109147)
AH105135 FRAME 1 -600000 (SUB AH111256)
AH111256 FRAME 1 (218)
AH88953 FRAME 1 -268385 (SUB AH94973)
AH94973 FRAME AR -317200 (SUB AH95294, AH97127, AH97129, AH96316,
H97709, AH88546 AND (3) AH95994)
AH95294 FRAME 1 -365600 (SUB AH98911)
AH98911 FRAME 1 -530050 (SUB AH103382, H109146 AND H109147)
AH103382 FRAME 1 -600000 (SUB AH111257)
AH111257 FRAME 1 (220)
AH88954 FRAME 1 -268385 (SUB AH94974)
AH94974 FRAME AR (SUB AH95349, AH97127, AH97129, AH96316,
H97709, AH88546 AND (3) AH95994)
AH95349 FRAME 1 -365600 (SUB AH98912)
AH103383 FRAME 1 -600000 (SUB AH111258) (SUB FOR AH98912)
AH111258 FRAME 1 (222)
AH88949 FRAME 1 -268385 (SUB AH94975)
AH94975 FRAME AR (SUB AH96339, AH97127, AH97129, AH96316,
H97709, AH88546 AND (3) AH95994)
AH96339 FRAME 1 -365600 (SUB AH98913)
AH103384 FRAME 1 -600000 (SUB AH111259) (SUB FOR AH98913)
AH111259 FRAME 1 (224)
AH95001 FRAME 1 -530050 (SUB AH103385 AND H109147)
AH103385 FRAME 1 -600000 (SUB AH111260)
AH111260 FRAME 1 (230)
2 H113371 FLOOR 1 (REPAIR ONLY - ARC WELD WHERE NEEDED)
200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99) 15-3
PN=29
HP4379 -UN-01JAN94
F23
FRAME, SHEETS, DIVIDERS, SKID PLATES, AND HEADER HEIGHT CONTROL
FRAME (RIGID AND FLEXIBLE)
g
15-4 200 SERIES CUTTING PLATFORMS PC1558 (01-OCT-99)
THIS PARTS LISTING IS CONTINUED
PN=30
Loading...