Page 1
WALK
GREENS
MOWERS
180C 220C 260C
Page 2
Three steps ahead
of the pack: the 180C,
220C and 260C Walk
Greens Mowers.
Our 18-, 22- and 26-inch walk greens
mowers have two things going for them:
They are among the lightest greens mowers
made today. And they are the best. A simple
scale told us the fi rst statement was true.
And 16,000 hours of testing proved the
second one.
What makes these walk greens mowers so
good? Here’s just a sampling: a handlebar
designed to fi t operators of all sizes. A muffl er that signifi cantly dampens sound levels.
A basket designed for better collection of
clippings. And bedknife-to-reel knobs for
easy adjustments.
We did all of this and more to ensure one
thing: to give you and your operators a cut
pattern that is straight and true. For more
about what makes these mowers the best
walk greens mowers made today, read on.
2
3
Page 3
John Deere provides an Operator
1
Presence Bail as standard
equipment on 18-, 22- and
26-inch walk greens mowers.
2
Quick-adjust handlebar fi ts
operators of all sizes.
3
Forward-mounting pivot point
reduces operator infl uence over
cutting plane of the mower.
Oil drain spout allows for quick
4
and neat oil changes.
Larger muffl er reduces noise.
5
Hand adjustment knobs allow for
6
easy, fi ne adjustment of
bedknife-to-reel. And less noise.
7
Redesigned drum drives have a
more effi cient design, requiring
less maintenance.
True 18-, 22- and 26-inch frames
8
allow the operator to follow the
cut lines and overlap with more
accuracy.
Grass catcher design improves
9
grass catching ability, operator
vision, and improved cut line
marking.
1
2
4
3
5
6
7
8
9
A. Fixed-position Reel
All of the C-Series Walk Greens Mowers feature a fi xed-position
reel for an even and consistent cutting height. Finger tight knobs
B
C
A
are in place for easy bedknife and front roller adjustments.
B. Increased Strength
Frame cross members have a double section for increased
strength. And rubber isolation mounts reduce engine vibration.
C. Easy Access Oil
Changing oil has never been easier or quicker, thanks to an oil
drain spout.
Page 4
From tee to green,
walk with the best.
For the undulating greens on your
course, the 18-inch walker, the 180C.
Like the 220C and 260C, the 180C
features a dual-traction rear drum
powered by an external differential drive.
This delivers even power distribution to
both sides for the straightest possible
tracking. It also makes for easy turning
and excellent maneuverability. A 2.0 mm
ultra-low-cut bedknife for cuts down
to 5/64-inch is standard equipment on
the 180C, and a 2.5 mm tournament
bedknife is available as an option.
180C WALK GREENS MOWER
Exceptional Parts Support
Behind every John Deere product is a parts support network to get you
the high-quality part you need fast. If your distributor does not have a
part in stock, in most cases you can order it by 5 p.m., and have it the
next day. Or even order parts online at www.JDParts.JohnDeere.com.
Tires
Transport wheels feature quick-release wheel latches and cast-iron
hubs ensure quick removal and installation with precision fi t.
Roller
The machine-grooved and machine-smooth front rollers are both cut from
solid bar stock to deliver more strength and better mowing performance.
Page 5
A solid all-around
per former, the 220C.
After getting feedback from customers, the
220C features a redesigned rear drum for
less maintenance, reduced sound levels,
an ergonomically improved handlebar, an
easier height-of-cut adjustment, and better
serviceability. A smaller pitched chain and
new chain adjuster help dampen sound.
A decreased distance between safety bail
and handlebar makes for easier handling.
And a forward-mounted pivot point aids in
machine tracking.
220C WALK GREENS MOWER
11-Blade Reel
The fi xed-position 11-blade reel is John Deere
manufactured and made out of high-strength
steel, for longer wear and less maintenance.
4
5
Page 6
260C WALK GREENS MOWER
The 260C. The perfect
mower for tees and
approach areas.
If you walk mow tees or want to improve
productivity on greens, the 260C is the
perfect choice. The 260C, like the 220C
and 180C, is the lightest walk mower in
its class. The height-of-cut adjustment is
easy, thanks to the bedknife-to-reel
adjustment knobs. You can choose between
an 11-blade or 7-blade reel. A larger muffl er
reduces noise. And all the controls move
forward for ease of operation.
Better Traction
The rear roller on the 260C is
dimpled for better traction.
Tuscon CC • Tuscon, AZ
Page 7
22B UTILITY TRAILER
1
accommodate a
e
base and a low cente
g.
r
m
.
3
l
allows
k
The best way to travel—
the 22B Utility Trailer
The 22B can be used with a wide range of
John Deere Mid-Duty Utility Vehic les or the
ProGator™ Heavy-Duty Utility Vehic le. Additional
optional axle bracket allows two greens
mowers to be trailered. And the 22B allows
the operator to leave transport wheels back
in the maintenance building if desired.
e of
r the
dditiona
ens
els bac
d.
Axle brackets easily adjust to
Axle brackets easily adjust to
1
accommodate all John Deere
walk greens mowers.
walk greens mowers.
Wide wheelbase and a low center
Wide wheel
2
of gravity add to the stability of
of gravity add to the stability of
the trailer on uneven ground or
the trailer on uneven ground or
while turning.
while turnin
Box and tailgate ramp are covered
Box and tailgate ramp are cove
3
with a rubber mat for easy loading
with a rubber mat for easy loadi
and protection for the drive drum,
and protection for the drive dru
roller, and bedknife.
roller, and bedknife
ll John Deer
1
2
3
6
7
Page 8
ENGINE*
Type
Cycle
Bore and Stroke
Piston Displacement
Compression Ratio
Horsepower
Direction of Rotation of Output Shaft
Inclination Limit
Idle Speed at Output Shaft
Maximum Speed at Output Shaft
FUEL
ype
T
Tank Capacity
OIL
T
ype
Capacity
Differential Drive Capacity
MACHINE
Cutting Equipment:
Cutting
Width
Cutting Height (Minimum)
Standard—3.0 mm Bedknife
Optional—2.5 mm Bedknife
Optional—2.0 mm Bedknife
Optional—Tee Bedknife
Frequency of Clip
Standard
REEL
Diameter
Number of Blades
terial
Ma
Bedknife—Standard
ROTARY BRUSH AND GREENS
TENDER CONDITIONER (Optional)
Brush
ertical Cutter Blades
V
Adjustable Brush or Cutter Height
Gear Drive
Grass Catcher
CLUTCHES
ransport
T
Reel Jaw-Type Clutch
Brush/GTC Jaw-Type Clutch
Traction Drum
TRAVELING DEVICE
orward Speed
F
Roller (Rear)
Roller (Front) (Grooved or Smooth)
DIMENSIONS
Length (w/T
Width (w/Tires Installed)
Height (w/Tires Installed)
Weight (Less Brush Drive and
Transport Wheels, with Catcher)
Certifi cate
ires Installed)
180C 220C
Honda, air-cooled GX120
4
x 1.73 in. (60 x 44 mm)
2.36 in.
118 cc
8.5:1
4.0 hp (2.98 kW) @ 3,600 rpm
Counterclockwise viewed from shaft side
Tilted up to 20 degrees in any direction
1,300 rpm
3,100 rpm
Regular grade—unleaded or leaded
qt. (2.5 L)
2.7 U.S.
SAE 30 or SAE 10W-30
qt. (0.57 L)
0.6 U.S.
0.7 U.S. pts. (0.35 L)
18 in. (45.7 cm)
(3.2 mm)
1/8 in.
7/64 in. (2.8 mm)
5/64 in. (2.0 mm) (standard on 180C)
N/A
0.182 in. (4.62 mm)
5 in. (127 mm)
11
t-treated chromium molybdenum steel
Hea
0.098-in. (2.5 mm) thick x 18-in. (45.8 cm) long
Interlocked w/reel, rotation in reverse
direction; 2 3/8-in.
Specially hardened carbon tool steel; star
shaped; 2 3/8-in. (60 mm) diameter; 60 blades
13/32 in. (10 mm) below to 5/8 in. (16 mm)
above cut
Gear driven from reel shaft opposite direction
of reel rotation powers brush or vertical cutter
6 Ib. (2.7 kg); polyethylene
Belt tension
On/off
On/off
aluminum, traction
Dual,
5.2 mph (8.4 km/h) with transport wheels
@ 3,500 engine rpm
Aluminum,
Machined steel, 2 3/8-in. (60 mm) diameter
(for cutting height adjustment)
37 in. (94.0 mm)
33 1/4 in.
47 in. (119.0 cm)
203 Ib. (92.3 kg)
ANSI B71.4-2004
*The engine horsepower information is provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower will
be less. Meets 2007 CARB standards.
(60 mm) diameter nylon
7 1/2-in. (190 mm) diameter
(84.5 cm)
Honda, air-cooled GX120
4
2.36 in. x 1.73 in. (60 x 44 mm)
118 cc
8.5:1
4.0 hp (2.98 kW) @ 3,600 rpm
Counterclockwise viewed from shaft side
Tilted up to 20 degrees in any direction
1,300 rpm
3,100 rpm
Regular grade—unleaded or leaded
2.7 U.S. qt. (2.5 L)
SAE 30 or SAE 10W-30
0.6 U.S. qt. (0.57 L)
0.7 U.S. pts. (0.35 L)
22 in. (55.9 cm)
1/8 in. (3.2 mm) (standard on 220C)
7/64 in. (2.8 mm)
5/64 in. (2.0 mm)
N/A
0.182 in. (4.62 mm)
5 in. (127 mm)
11
Heat-treated chromium molybdenum steel
0.118-in. (3 mm) thick x 22-in. (56.0 cm) long
Interlocked w/reel, rotation in reverse
direction; 2 3/8-in. (60 mm) diameter nylon
Specially hardened carbon tool steel; star
shaped; 2 3/8-in. (60 mm) diameter; 75 blades
13/32 in. (10 mm) below to 5/8 in. (16 mm)
above cut
Gear driven from reel shaft opposite direction
of reel rotation powers brush or vertical cutter
7 Ib. (3.2 kg); polyethylene
Belt tension
On/off
On/off
Dual, aluminum, traction
5.2 mph (8.4 km/h) with transport wheels
@ 3,500 engine rpm
Aluminum, 7 1/2-in. (190 mm) diameter
Machined steel, 2 3/8-in. (60 mm) diameter
(for cutting height adjustment)
37 in. (94.0 mm)
37 1/4 in. (94.6 cm)
47 in. (119.0 cm)
219 Ib. (99.5 kg)
ANSI B71.4-2004
260C
Honda, air-cooled GX120
4
2.36 in. x 1.73 in. (60 x 44 mm)
118 cc
8.5:1
4.0 hp (2.98 kW) @ 3,600 rpm
Counterclockwise viewed from shaft side
Tilted up to 20 degrees in any direction
1,300 rpm
3,100 rpm
Regular grade—unleaded or leaded
2.7 U.S. qt. (2.5 L)
SAE 30 or SAE 10W-30
0.6 U.S. qt. (0.57 L)
0.7 U.S. pts. (0.35 L)
26 in. (66.0 cm)
1/8 in. (3.2 mm); max of 1.375-in. (35 mm)
with 3-in. roller
N/A
N/A
3/16 in. (4.8 mm)
0.182 in. (4.62 mm) 11 blade
0.286 in. (7.26 mm) 7 blade
5 in. (127 mm)
11 or 7 blade
Heat-treated chromium molybdenum steel
0.118-in. (3.0 mm) thick x 26-in. (66 cm) long
Interlocked w/reel, rotation in reverse
direction; 2 3/8-in. (60 mm) diameter nylon
Specially hardened carbon tool steel; star
shaped; 2 3/8-in. (60 mm) diameter; 88 blades
13/32 in. (10 mm) below to 5/8 in. (16 mm)
above cut
Gear driven from reel shaft opposite direction
of reel rotation powers brush or vertical cutter
8 Ib. (3.7 kg); polyethylene
Belt tension
On/off
On/off
Dual, aluminum, traction
5.2 mph (8.4 km/h) with transport wheels
@ 3,500 engine rpm
Aluminum, 7 1/2-in. (190 mm) diameter
Machined steel, 2 3/8-in. (60 mm) diameter
(for cutting height adjustment)
37 in. (94.0 mm)
41 1/4 in. (104.8 cm)
47 in. (119.0 cm)
235 Ib. (106.8 kg)
ANSI B71.4-2004
PLATINUM PARTNE R
DKA2633 (08-01) Litho in U.S.A. 08-2633
This literature has been compiled for worldwide circulation. While general information, pictures and descriptions are provided, some illustrations and text may
include fi nance, credit, insurance, product options and accessories NOT AVAILABLE in all regions. PLEASE CONTACT YOUR LOCAL DEALER FOR DETAILS. John Deere
reserves the right to change specifi cation, design and price of the products described in this literature without notice. John Deere’s green and yellow color scheme,
the leaping deer symbol, and JOHN DEERE are trademarks of Deere & Company.
www.JohnDeere.com
Loading...