J&M Blu<>Hub® Bluetooth®
Corded Headset Adapter Terminal
for 2018-2019 Honda GL1833
#
CBLU-GL1833
© 2018 J&M Corporation. All rights reserved. 9/18
Installation
and Operation
Instructions
Table of Contents
Product Description Section 1
Safety & General Information Section 2
Package Contents Section 3
1. Product Description
This custom made and totally new J&M BluHub® CORDED
helmet headset adapter terminal, will link directly to the
Wing’s main audio system by Bluetooth and provide ALL of
the audio system functions that are standard on the new
Wing, to one or two corded helmet headsets.
WHILE at the same time providing a constant and
continuous “private” driver/passenger intercom system with
simple to operate volume control on the face of the BluHub
component.
ALL standard handlebar levers/buttons and system
functions from the new Wing, will control everything going to
the corded helmet headsets, including stereo music from all
sources, cell phone, navigation, Apple car-play and 40-CH CB
radio functions.
Both driver and passenger can talk on the phone, thru the
system at the same time they are talking to each other over
the intercom, along with the CB radio.
If only one headset is plugged into the system, the intercom
volume control can be rotated to minimum so that no voice
talkback is heard if the bike is being ridden solo.
Supplied headset cable jacks are the standard 5-pin
configuration that have been used on all Gold Wings from
1980-2017.
If both rider and/or passenger decide to use Bluetooth
headsets instead of corded at any given time, they can link
their Bluetooth headsets to the Wing’s system, instead of
the BluHub and all systems will function normal, with NO
interference from the BluHub.
This is an easy to install, totally plug-n-play CORDED helmet
headset solution for the 2018-2019 Honda Gold Wing
GL1833 that is 12v powered, turns on/off with the ignition
and there are NO BATTERIES to charge.
2. Safety and General Information
IMPORTANT INFORMATION FOR SAFE AND EFFICIENT
OPERATION. READ THIS INFORMATION BEFORE USING
YOUR DEVICE.
Users are not permitted to make changes or modify the
device in any way. Changes or modifications not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment. See 47 CFR
Sec. 15.21.
Installation Instructions Section 4
Linking/Pairing Scenarios Section 5
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation. See FCC
47 CFR Sec. 15.19 (3).
ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY:
Note: Nearly every electronic device is susceptible to
electro-magnetic interference (EMI) if inadequately shielded,
designed or otherwise configured for electromagnetic
compatibility.
FACILITIES: To avoid electromagnetic interference and/
or compatibility conflicts, turn off your device in any facility
where posted notices instruct you to do so. Hospitals
or health care facilities may be using equipment that is
sensitive to external RF energy.
AIRCRAFT: When instructed to do so, turn off your device
when on board an aircraft. Any use of a device must be
in accordance with applicable regulations per airline crew
instructions.
MEDICAL DEVICES
HEARING AIDS: Some devices may interfere with some
hearing aids. In the event of such interference, you may
want to consult with your hearing aid manufacturer to
discuss alternatives.
OTHER MEDICAL DEVICES
If you use any other personal medical device, consult the
manufacturer of the device to determine if it is adequately
shielded from RF energy. Your physician may be able to
assist you in obtaining this information.
Industry Canada Notice to Users: Operation is subject to
the following two conditions: (1) This device may not cause
interference and (2) This device must accept any interference, including interference that may cause undesired
operation of the device.
FCC Notice to Users: This equipment has been tested and
found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
the receiver.
• Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
3. Package Contents
• (1) Blu<>Hub adapter/control terminal.
• (1) Connection harnesses for the 2018-2019 Honda
Gold Wing. (NOT for airbag models)
4. Installation Instructions
1. Install VIDEO at https://www.jmcorp.com/ProductDetail.
asp?ProductID=CBLU-GL1833
2. Remove the left side cover, right side cover and seat.
3. Open the center console door and locate the large
rubber grommet that contains the USB thumb drive
cable.
4. Pull this grommet out of its mounting hole and carefully
cut a slot from the side with a small pair of dykes.
5. Uncoil the included section of steel wire and push one
end thru the grommet hole inside the glove box, down
thru to the location under the seat.
6. Wrap the end of the wire around the large female 8-pin
din plug from the main harness and the pull this end
carefully up into the center console, thru the grommet
hole.
7. Slide this new cable thru the slot in the grommet, then
reinsert grommet as you leave about 5” of the new
cable inside the center console.
10. Route both driver & passenger headset female plugs to
a location so that they will both protrude from under the
left side of the seat once reinstalled.
11. Secure all cables and wires with tie straps provided.
12. Plug the BluHub control terminal into the harness inside
the center console, plug in one or two helmet headsets,
turn the ignition to the ON or ACC position, rotate the
intercom volume knob clockwise about half way and
verify the driver/passenger intercom speech function.
13. Now reinstall both left & right side covers along with the
seat.
5. General Operation Instructions
1. Turn the ignition to the ON or ACC position.
2. Put the BluHub into pairing mode by first holding
down on the multifunction button for approximately
10 seconds until the unit turns off, and then release.
3. Then press and hold the multifunction button again
cycling thru the slow flashing blue, to flashing red and
blue, and then release as the BluHub is now in pairing
mode.
4. Then for the Honda system menu options go to Audio
Setting, then Bluetooth setting, then rider headset
pairing, then inquiry, then press abort when you see the
JM_CBLU_1833 appear at the bottom of the screen,
then press JM_CBLU_1833, and press OK as device
is successfully paired, then return to the main audio
system screen.
5. Once linked the first time, the BluHub will automatically
link back to the audio system each time the ignition
is turned on or to the accessory position, without any
additional input from the rider or passenger.
6. Now slide the BluHub back down into the storage
compartment, hop on the new Wing, plug in your helmet
headsets, adjust the intercom volume to a comfortable
level and you are ready to go.
8. Plug in the power supply box into the cable harness
under the seat, connect the orange wire to the acc
terminal + on the fuse block, the red wire with in-line
fuse direct to the positive (+) terminal of the battery and
the black wire to the frame ground bolt just above the
battery.
9. Secure the power supply box to an out of the way
location under the seat with double-back tape already
affixed.
Thank you for the confidence you have shown by purchasing one of J&M’s innovative products. If you have any questions during the installation, or require
further assistance, you may call us at USA 1-520-624-7000
Monday thru Friday 8:00 AM to 5:00 PM Mountain Standard Time,
7. All system volume adjustments will now be made using
the normal handlebar mounted controls for the corded
headsets.
Supported Bluetooth Profiles:
• A2DP (Advanced Audio Distribution Profile)
• HFP (Hands Free Profile)
114 S. Cherry Avenue
Tucson, Arizona U.S.A.
Tel: (800) 358-0881
www.jmcorp.com
E-mail: audio@jmcorp.com
WARRANTY AND REPAIR INFORMATION
TWO YEAR LIMITED WARRANTY In order to facilitate the servicing of this warranty, the Warranty Registration Form should be filled out and
returned within 10 days of the date of purchase. However, return of the Warranty Registration Form is not a precondition of this warranty,
and this Warranty will be observed by J&M CORPORATION whether or not the Warranty Registration Form is returned,
on the condition that other satisfactory evidence of the date of the original purchase is provided to J&M CORPORATION.
WHO PROVIDES THE WARRANTY? This warranty is provided by J&M CORPORATION.
WHO IS PROTECTED? This warranty is extended only to the original owner of this J&M CORPORATION product and may not be trans-
ferred or assigned.
WHAT IS COVERED AND HOW LONG? This warranty covers all defects in material or workmanship of our product for a period of
2 years from date of original retail purchase. At its option, J&M CORPORATION will repair or replace any defective part(s) or
equipment.
The provisions of the warranty shall not apply to any unit which has been subjected to misuse, neglect, incorrect mechanical or
electrical installation, unauthorized modifications, accident, nor to units which have been repaired or altered outside of our factory.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY In the event that the product does not conform to this warranty, the product
should be shipped prepaid to the J&M CORPORATION service facility. Transportation charges, insurance fees, and labor costs for shipment,
removal, or reinstallation of our product are not covered by this warranty. Loss or damage in shipment is the sole responsibility of the freight
carrier.
FOR YOUR INFORMATION Repair as provided under this warranty is the exclusive remedy of the consumer. J&M CORPORATION shall
not be liable for any incidental or consequential damages or for breach of any express or implied warranty on this product. Except to the
extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose on this product is limited
in duration to the duration of the warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages,
or allow limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives
you specific legal rights which vary from state to state.
J&M CORPORATION reserves the right to make changes in design and to make improvements in its products without the obligation to
incorporate the changes or improvements in any of its previously manufactured products.
J&M CORPORATION has not authorized anyone to make representations or warranties other than the warranty contained herein.
The above warranty is effective for all products manufactured after 10/01/86.
NON-WARRANTY REPAIR RATES J&M CORPORATION reserves the right to change the labor repair rates without prior notice. At the time
of this printing the out-of- warranty repair is $40 per hour for labor only. However, the customer is advised to verify the
current rate when he/she calls customer service to obtain the return authorization number.
FACTORY SERVICE ADDRESS J&M Corporation, 1415 S. Cherry Avenue, Tucson, Arizona, 85713, U.S.A. • Tel: 1-800-358-0881
audio@jmcorp.com • www.jmcorp.com
CUSTOMER SERVICE NUMBER 1-800-358-0881
WARRANTY REGISTRATION FORM Please fill out this card completely and mail it immediately after purchase. Please be sure that your zip code
and serial number (if applicable) are legible. This will help us to serve you better.
(PLEASE PRINT)
Name ______________________________________________________________________________________________________________________________________________________
Address _____________________________________________________________________________________________________________________________________________________
City _______________________________ _________________________________State __________________________ Zip ______________________________________________________
Motorcycle m Other m E-mail ______________________________________________________________________________________________________
Make ___________________________________________ Model ______________________________________ Year __________________
Product part number ______________________________________________________________________
Serial number (if applicable)________________________________________________________________
Date of purchase _________________________________________________
Name of dealer it was purchased from ____________________________________________________________________________________
Mail to:
J&M Corporation
1415 S. Cherry Avenue
Tucson, AZ 85713
U.S.A.
Loading...