Jetway Computer NAF93-Q77 User Manual

USER'S MANUAL

Intel Q77/B75 Express Chipset

Based

M/B for LGA 1155 Quad Core Ready

Intel Core Processor

No. G03-NAF93-F

Rev: 2.0

Release date: October 11, 2013

Trademark:

* Specifications and Information contained in this docume ntation ar e furnishe d for inf ormation use only , and ar e

subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

ENVIRONMENTAL SAFETY INSTRUCTION...........................................................................iii

ENVIRONMENTAL PROTECTION ANNOUCEMENT..............................................................iii

USER’S NOTICE .......................................................................................................................iv

MANUAL REVISION INFORMATION.......................................................................................iv

ITEM CHECKLIST.....................................................................................................................iv

CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD

1-1 SPECIFICATION.........................................................................................................1

1-2 LAYOUT DIAGRAM....................................................................................................2

CHAPTER 2 HARDWARE INSTALLATION

2-1 JUMPER SETTING.....................................................................................................5

2-2 CONNECTORS AND HEADERS................................................................................10

2-2-1 REAR I/O BACK PANEL CONNECTORS....................................................10

2-2-2 MOTHERBOARD INTERNAL CONNECTORS............................................11

2-2-3 HEADER PIN DEFINITION ...........................................................................14

TABLE OF CONTENT

CHAPTER 3 INTRODUCING BIOS

3-1 ENTERNING SETUP...................................................................................................20

3-2 BIOS MENU SCREEN ................................................................................................20

3-3 FUNCTION KEYS .......................................................................................................21

3-4 GETTING HELP ..........................................................................................................21

3-5 MENU BARS...............................................................................................................22

3-6 MAIN MENU................................................................................................................22

3-7 ADVANCED MENU.....................................................................................................23

3-8 CHIPSET MENU..........................................................................................................29

3-9 BOOT MENU...............................................................................................................32

3-10 SECURITY MENU.......................................................................................................33

3-11 SAVE & EXIT MENU...................................................................................................34

Environmental Safety Instruction

z Avoid the dusty, humidity and temperature extremes. Do not place the product in

any area where it may become wet.

z 0 to 40 centigrade is the suitable temperature. (The figure comes from the request

of the main chipset)

z Generally speaking, dramatic changes in temperature may lead to contact

malfunction and crackles due to constant thermal expansion and contraction from the welding spots’ that connect components and PCB. Computer should go through an adaptive phase before it boots when it is moved from a cold environment to a warmer one to avoid condensation phenomenon. These water drops attached on PCB or the surface of the components can bring about phenomena as minor as computer instability resulted from corrosion and oxidation from components and PCB or as major as short circuit that can burn the components. Suggest starting the computer until the temperature goes up.

z The increasing temperature of the capacitor may decrease the life of computer.

Using the close case may decrease the life of other device because the higher temperature in the inner of the case.

z Attention to the heat sink when you over-clocking. The higher temperature may

decrease the life of the device and burned the capacitor.

Environmental Protection Announcement

Do not dispose this electronic device into the trash while discarding. To minimize pollution and ensure environment protection of mother earth, please recycle.

iii

USER’S NOTICE

COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.

THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AN D WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE).

PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT INTENT TO INFRINGE.

Manual Revision Information

Reversion Revision History Date

2.0 Second Edition October 11, 2013

Item Checklist

Motherboard

User’s Manual

DVD for motherboard utilities

Cable(s)

I/O Back panel shield

Chapter 1

Introduction of the Motherboard

1-1 Specification

Spec Description

Design Chipset

LGA1155 CPU Socket

Memory Slot

Expansion Slots

Storage Dual LAN Chip

HD Audio Chip BIOS

Multi I/O

z ATX form factor; PCB size: 30.0 x24.4 cm z NAF93-Q77 series: Intel Q77 Express Chipset

z NAF93-B75 series: Intel B75 Express Chipset z Supports 3rd and 2nd Generation Intel® Core™ i7, Core™ i5,

Core™ i3 series processor in LAG1155 Package

* for detailed CPU support information please visit our website

z DDRIII RAM module slot x 4 z Supporting four DDRIII 1600/1333/1066MHz RAM Module

expandable to 32 GB (Maximum)

z Support dual-channel function z 1 pcs* PCI-Express x16 slot z 1 pcs* PCI-Express x4 slot z 1 pcs* PCI-Express x1 slot z 4 pcs *32-bit PCI slot z 1 pcs* Full-size MSATA slot z 1 pcs*Half-size Mini-PCIE slot z NAF93-Q77 series: Support 4 SATAII ports & 2 SATAIII ports z NAF93-B75 series: Support 5 SATAII ports & 1 SATAIII port z Integrated Intel 82574L and 82579LM Gigabit Ethernet LAN chip

that supports Fast Ethernet LAN function of providing 10/100/1000Mbps Ethernet data transfer rate

z Realtek ALC662 6-channel Audio Codec integrated z Audio driver and utility included

z 64MB DIP Flash ROM z USB 3.0 port connector x2

z HDMI port connector x1 & DVI-D port connector x1& VGA port

connector x1

z Serial port connector x2 z USB 2.0 port connector x4 z RJ-45 LAN connector x2 z Audio connector x3 (Line-in, Line-out, MIC) z Front panel audio header x1 z HDMI-SPDIF header x1 z CDIN header x1 z Parallel header x1 z TPM 1.2 header x1 z GPIO header x1 z USB 2.0 header x2 (Optional for NAF93-Q77 series) z USB 2.0 header x1 (Optional for NAF93-B75 series) z USB 3.0 header x1 z Front panel header x1 z POWER LED header x1 z Speaker header x1 z CIR header x1 z LANLED header x2 z SM_BUS header x1 z TX-RX COM header x 1 z COM port header x 8

1-2 Layout Diagram

Rear IO Diagram

USB 3.0 Ports

HDMI Port

Serial Port 1

Serial Port 2

DVI-D Port

VGA Port

Motherboard Internal Diagram

KBMS Header

USB 3.0 PortS over

HDMI port

Serial Port s

(COM1 over COM2)

DVI –D Port over

VGA Port

LGA1155

CPU Socket

SYS FAN1

Header

ATX 12V

Power Connector

RJ-45 LAN Ports

USB 2.0 Ports

CPUFAN Header

Line-IN/

Optical SPDIF OUT

Line-OUT

MIC-IN

DDRIII

DIMM Slot x 4

ATX Powe

Connector

RJ-45 LAN Ports

Over USB 2.0 Ports

RJ-45 LAN Ports

Over USB 2.0 Ports

Audio Connectors

LAN1LED Header

CI E

ress 2.0 x1 Slot

LAN2LED Header

CI Slots

32-bit

HDMI S/PDIF Header

Front Panel

Audio Heade

PCI Express x16 Slot (PE1) *

PCI Express 2.0 x 4 Slot

Parallel Header

CDIN Header

USB 3.0 Header

Half-size

Mini-PCIE Slot

GPIO Header

DP Connector*

Full-size

MSATA Slot*

TPM Header

TX-RX COM Heade

Intel Q77/B75

Chi

set

USB 2.0 Header*

SM_BUS Header

SATA Ports*

(SATA1/SATA2)

SATA Ports (SARA3_4)

SATA Ports

(SARA5/SATA6

Speaker Header

PWR LED Header

Front Panel Header

Serial Ports (COM3/5/7/9)

SYS FAN2 Header

Serial Ports (COM4/6/8/10) CIR Header

USB 2.0 Header

(Optional for NAF93-Q77)*

JBAT

JP7

JP5JP

JP10JP

Note: 1.PE1

CPU and supports

mSATA slot

optional for customize model. 4.

NAF93-B75

for

NAF93-Q77,

illustration is from model

slot supports

PCI-Express 3.0 x1

PCI-Express 2.0 x16

6 specification when using Intel

specification when using Intel® Sandy Bridge

share with SATA6, only one of them can function at a time;

NAF93-Q77

has only one USB 2.0 header (USB2). 5.

SATAII 3G/s port for

NAF93-Q77

NAF93-B75; 6.

unless otherwise stated.

has two USB 2.0 headers (USB2; USB3),

SATA1

port functions as SATAIII 6G/s port

The diagrams used in this manual for

Ivy Bridge CPU; 2.

3. EDP connector

is only

Motherboard Jumper Position

JP2

CASE_OPEN

Jumper

Jumper Name Description

JBAT CMOS RAM Clear Function Setting 3-pin Block JP2 Mini PCI-E Power VCC3.3V/3.3VSB Select 3-pin Block JP3 (Optional) EDP Panel Power 5V/3.3V Select 3-pin Block JP1 COM1 Ports Pin9 Function Select 6-pin Block JP4 COM3 Header Pin9 Function Select 6-pin Block JP5 COM5 Header Pin9 Function Select 6-pin Block

JP6 COM7 Header Pin9 Function Select 6-pin Block JP7 COM9 Header Pin9 Function Select 6-pin Block JP8 COM4 Header Pin9 Function Select 6-pin Block JP9 COM6 Header Pin9 Function Select 6-pin Block JP10 COM8 Header Pin9 Function Select 6-pin Block JP11 COM10 Header Pin9 Function Select 6-pin Block JP12 COM4 Header RS232/485/422 Function Select 6-pin Block Case_open Case Open Message Display Function Select 2-pin Block

Connectors

Connector Name

ATXPWR ATX Power Connector ATX12V1 ATX 12V Power Connector USB4 USB 3.0 Connector X2 HDMI High-Definition Multimedia Interface VGA Video Graphic Attach Connector DVI DVI-D Port Connector COM1(Top)/COM2(Bottom) Serial Port COM Connector X2 UL1(Middle & Bottom )/UL2(Middle & Bottom) UL1(Top)/UL2(Top) RJ-45 LAN Connector X2 AUDIO1 Audio Connector X3 SATA1 SATAIII Connector X1

SATA2 SATA3_4/SATA5/SATA6 SATAII Connectors X4

EDP (Optional) EDP connector

USB 2.0 Port Connector X4

NAF93-Q77 Series: SATAIII Connector X1 NAF93-B75 Series: SATAII Connector X1

Headers

Header Name Description

FP_AUDIO Front panel audio Header 10-pin block CDIN1 CD Audio-In Header 4-pin Block HDMI_SPDIF HDMI_SPDIF Out Header 2-pin Block KBMS PS/2 Keyboard & Mouse Header 6-pin Block SPEAK Speaker Header 4-pin Block PWRLED Power LED 3-pin Block JW_FP

(Front Panel Header) CIR CIR Header 8-pin Block

USB1 USB 3.0 Header 20-pin Block USB2/USB3(Optional) USB 2.0 Header 10-pin Block COM 3/4/5/6/7/8/9/10 Serial Port Header 10-pin Block TX-RXCOM RS 422/485 port headers 4-pin block GPIO_CON GPIO Header 10-pin Block TPM TPM Header 20-pin Block PARALLEL Parallel Port Header 26-pin Block LAN1LED/LAN2LED LANLED 2-pin Block SM_BUS SMBUS Header 4-pin Block SYSFAN1 SYSFAN1 Header 3-pin Block SYSFAN2/CPUFAN1 FAN Header 4-pin Block

PWR LED/ HD LED/ /Power Button

/Reset

10-pin Block

;

Chapter 2

Hardware Installation

2-1 Jumper Setting

(1) JBAT (3-pin): Clear CMOS

JBAT

1-2 closed : Normal

JBAT

2-3 Short： Clear CMOS

CMOS Clear Setting

(2)JP2 (3-pin): Mini PCI-E Power VCC 3.3V/3.3 VSB Select

JP2

1-2 closed ： MINI PCI -E VCC= 3. 3V;

JP2

2-3 closed ： MINI PCI-E VCC= 3.3VSB

(3)JP3 (3-pin): EDP Panel Power 5V/3.3 V Select

JP3

1-2 closed ： EDP Panel Power=5V;

JP3

2-3 closed ：EDP Panel Power=3. 3V;

*Note:

JP3 is optional for customize model with EDP connector.

(4) JP1 (6-pin): COM1 Port Pin9 Function Select

JP1

1-2 closed: RS232;

3-4 closed : +12V;

(5) JP4 (6-pin): COM3 Port Pin9 Function Select

JP4

1-2 closed: RS232;

3-4 closed : +12V;

(6) JP5(6-pin): COM5 Port Pin9 Function Select

5-6 closed : +5V

JP5

1-2 closed: RS232;

3-4 closed : +12V;

5-6 closed : +5V

(7) JP6(6-pin): COM7 Port Pin9 Function Select

JP6

1-2 closed: RS232;

3-4 closed : +12V;

(8) JP7(6-pin): COM9 Port Pin9 Function Select

JP7

1-2 closed: RS232;

3-4 closed : +12V;

(9) JP8(6-pin): COM4 Port Pin9 Function Select

5-6 closed : +5V

JP8

1-2 closed: RS232;

3-4 closed : +12V;

5-6 closed : +5V

(10) JP9(6-pin): COM6 Port Pin9 Function Select

JP9

1-2 closed: RS232;

3-4 closed : +12V;

(11) JP10(6-pin): COM8 Port Pin9 Function Select

JP10

1-2 closed: RS232;

3-4 closed : +12V;

(12) JP11(6-pin): COM10 Port Pin9 Function Select

5-6 closed : +5V

JP11

1-2 closed: RS232;

3-4 closed : +12V;

5-6 closed : +5V

+ 26 hidden pages

Jetway Computer NAF93-Q77 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual