JET JDP-17 Operating Instructions and Parts Manual

Download

This .pdf document is bookmarked

Operating Instructions and Parts Manual

16-speed Woodworking Drill Press

Model JDP-17

For serial no. 17093334 and higher

JET

1.0 Warranty and Service

JET® warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday.

Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website.

• JET products carry a limited warranty which varies in duration based upon the product. (See chart below)

• Accessories carry a limited warranty of one year from the date of receipt.

• Consumable items are defined as expendable parts or accessories expected to become inoperable within a

reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects.

Who is Covered

This warranty covers only the initial purchaser of the product from the date of delivery.

What is Covered

This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty does not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack of maintenance. JET woodworking machinery is designed to be used with Wood. Use of these machines in the processing of metal, plastics, or other materials outside recommended guidelines may void the warranty. The exceptions are acrylics and other natural items that are made specifically for wood turning.

Warranty Limitations

Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a Two Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.

How to Get Technical Support Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof of initial purchase when calling. If a product requires further inspection, the Technical Service representative will

explain and assist with any additional action needed. JET has Authorized Service Centers located throughout the United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service Center Locator on the JET website.

More Information

JET is constantly adding new products. For complete, up-to-date product information, check with your local distributor or visit the JET website.

How State Law Applies

This warranty gives you specific legal rights, subject to applicable state law.

Limitations on This Warranty

JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever. JET

Product Listing with Warranty Period

90 Days – Parts; Consumable items; Light-Duty Air Tools 1 Year – Motors; Machine Accessories; Heavy-Duty Air Tools; Pro-Duty Air Tools 2 Year – Metalworking Machinery; Electric Hoists, Electric Hoist Accessories; Woodworking Machinery used for industrial or commercial purposes 5 Year – Woodworking Machinery Limited Lifetime – JET Parallel clamps; VOLT Series Electric Hoists; Manual Hoists; Manual Hoist Accessories; Shop Tools; Warehouse & Dock products; Hand Tools

NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand.

branded products are not sold in Canada by JPW Industries, Inc.

2.0 Table of contents

Section Page

1.0 Warranty and Service ..................................................................................................................................... 2

2.0 Table of contents ............................................................................................................................................ 3

3.0 Safety warnings .............................................................................................................................................. 4

4.0 About this manual .......................................................................................................................................... 5

5.0 Specifications ................................................................................................................................................. 6

5.1 Base mounting holes for JDP-17 ................................................................................................................ 7

6.0 Setup and assembly ....................................................................................................................................... 8

6.1 Unpacking .................................................................................................................................................. 8

6.2 Shipping contents ....................................................................................................................................... 8

6.3 Additional tools required for assembly ....................................................................................................... 8

6.4 Location ...................................................................................................................................................... 9

6.5 Assembly .................................................................................................................................................... 9

6.6 Chuck key and wrench storage ................................................................................................................ 11

7.0 Electrical connections .................................................................................................................................. 11

7.1 Grounding instructions ............................................................................................................................. 11

7.2 Extension cords ........................................................................................................................................ 12

8.0 Adjustments ................................................................................................................................................. 12

8.1 Tools needed for adjustments .................................................................................................................. 12

8.2 Table movement ....................................................................................................................................... 12

8.3 Table insert leveling ................................................................................................................................. 13

8.4 Table slots ................................................................................................................................................ 13

8.5 Chuck and arbor removal ......................................................................................................................... 13

8.6 Installing bits ............................................................................................................................................. 13

8.7 Changing spindle speeds ......................................................................................................................... 14

8.8 Depth stop ................................................................................................................................................ 14

8.9 Quill retraction lock ................................................................................................................................... 15

8.10 Laser adjustment .................................................................................................................................... 15

8.11 LED work light ........................................................................................................................................ 16

9.0 Operating controls ........................................................................................................................................ 16

9.1 Control panel ............................................................................................................................................ 16

9.2 Safety key ................................................................................................................................................. 17

10.0 Operation ................................................................................................................................................... 17

10.1 Work piece positioning ........................................................................................................................... 17

10.2 General Inspection ................................................................................................................................. 17

10.3 Speed settings ........................................................................................................................................ 17

11.0 User-maintenance ...................................................................................................................................... 17

11.1 Belt replacement .................................................................................................................................... 18

11.2 Return spring .......................................................................................................................................... 18

12.0 Speed chart ................................................................................................................................................ 19

13.0 Troubleshooting the JDP-17 ...................................................................................................................... 20

14.0 Replacement Parts ..................................................................................................................................... 20

14.1.1 JDP-17 Drill Press – Exploded View ................................................................................................... 21

14.1.2 JDP-17 Drill Press – Parts List ............................................................................................................ 22

15.0 Electrical Connections – JDP-17 Drill Press .............................................................................................. 26

3.0 Safety warnings

1. Read and understand the entire owner's manual before attempting assembly or operation.

2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

3. Replace the warning labels if they become obscured or removed.

4. This drill press is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a drill press, do not use until proper training and knowledge have been obtained.

5. Do not use this drill press for other than its intended use. If used for other purposes, JET disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.

6. Always wear approved safety glasses/face shields while using this drill press. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.

7. Before operating this drill press, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.

8. Wear ear protectors (plugs or muffs) during extended periods of operation.

9. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

10. Make certain the switch is in the OFF position before connecting the machine to the power supply.

11. Make certain the machine is properly grounded.

12. Make all machine adjustments or maintenance with the machine unplugged from the power source.

13. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

14. Do not start the drill press while the cutting tool is in contact with the workpiece.

15. Secure workpiece firmly against table and make sure table is locked, before drilling.

16. Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately after completion of maintenance.

17. Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

18. Provide for adequate space surrounding work area and non-glare, overhead lighting.

19. Keep the floor around the machine clean and free of scrap material, oil and grease.

20. Keep visitors a safe distance from the work area. Keep children away.

21. Make your workshop child proof with padlocks, master switches or by removing starter keys.

22. Give your work undivided attention. Looking around, carrying on a conversation and “horseplay” are careless acts that can result in serious injury.

23. Maintain a balanced stance at all times so that you do not fall into the bit or other moving parts. Do not overreach or use excessive force to perform any machine operation.

24. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and more safely.

25. Use recommended accessories; improper accessories may be hazardous.

26. Maintain tools with care. Keep tools sharp and clean for the best and safest performance. Follow instructions for lubricating, and changing accessories.

27. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do not use your hands.

28. Do not stand on the machine. Serious injury could occur if the machine tips over.

29. Never leave the machine running unattended. Turn the power off and do not leave the machine until it comes to a complete stop.

30. Remove loose items and unnecessary work pieces from the area before starting the machine.

31. Don’t use in dangerous environment. Don’t use power tools in damp or wet location, or expose them to rain. Keep work area well lighted.

WARNING: This product can expose you to chemicals including lead which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to http://www.p65warnings.ca. gov.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or possible

machine damage.

This means that if precautions are not heeded, it may result in serious, or possibly even

fatal, injury.

WARNING: Drilling, sawing, sanding or machining wood products generates wood dust and other substances known to the State of California to cause cancer. Avoid inhaling dust generated from wood products or use a dust mask or other safeguards for personal protection.

Wood products emit chemicals known to the State of California to cause birth defects or other reproductive harm. For more information go to http://www.p65warnings.ca.gov/wood.

4.0 About this manual

This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model JDP-17 Drill Press. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. Your machine has been designed and constructed to provide consistent, long-term operation if used in accordance with the instructions as set forth in this document.

This manual is not intended to be an exhaustive guide to drill press operational methods, use of jigs or aftermarket accessories, choice of bits or wood stock, etc. Additional knowledge can be obtained from experienced users or trade articles. Whatever accepted methods are used, always make personal safety a priority.

If there are questions or comments, please contact your local supplier or JET. JET c an also be reached at our web site: www.jettools.com.

Retain this manual for future reference. If the machine transfers ownership, the manual should accompany it.

Read and understand the entire contents of this manual befor e attempting assembly

or operation! Failure to comply may ca use serious injury!

5.0 Specifications

Model number ............................................................................................................................................. JDP-17

Stock number .............................................................................................................................................. 716300

Motor and electricals:

Motor type ....................................................................... totally enclosed fan cooled, induction, capacitor start

Horsepower ............................................................................................................................................. 3/4 HP

Phase ........................................................................................................................................................ single

Voltage ............................................................................................................................................... 115V only

Cycle .......................................................................................................................................................... 60Hz

Listed FLA (full load amps) ........................................................................................................................... 9 A

Starting amps .............................................................................................................................................. 18 A

Running amps (no load) ................................................................................................................................ 3 A

Start capacitor .......................................................................................................................... 150μF, 125VAC

Run capacitor ............................................................................................................................. 40μF, 250VAC

Power transfer ............................................................................................................................... 2 poly v-belts

On/off switch ...................................................................................... push button with safety key, paddle stop

Motor speed ...................................................................................................................................... 1720 RPM

Power cord .................................................................................................................... 16 AWG, 6 ft. (183 cm)

Power plug installed ....................................................................................................... 115V, 15A with ground

Recommended circuit size Sound emission

................................................................................................ 80dB at 39” (1m) without load

Laser system .......................................................................................................................................... Class II

Head and Capacities:

Swing 3 .................................................................................................................................... 16-7/8” (430mm)

Chuck style and shank capacity .......................................................................................... keyed, 5/8” (16mm)

Chuck arbor taper ......................................................................................................................... JT-3 to MT-2

Spindle taper .............................................................................................................................................. MT-2

Spindle travel, maximum ................................................................................................................ 5” (127 mm)

Spindle travel per one revolution of handle .................................................................................... 5” (127 mm)

Quill diameter .............................................................................................................................. 2.05” (52 mm)

Number of spindle speeds ............................................................................................................................. 16

Maximum no-load speed range.............................................................................................. 210 to 3500 RPM

Maximum spindle to table distance .............................................................................................. 30” (763 mm)

Maximum spindle to base distance ...................................................................................... 46-1/2” (1180 mm)

Maximum chuck to table distance .......................................................................................... 25-1/4” (640 mm)

Maximum chuck to base distance ........................................................................................ 42-1/2” (1080 mm)

Work lamp .................................................................................................................... integrated, pivoting LED

Depth stop type ...................................................................................................................................... internal

Materials:

Head..................................................................................................................................................... cast iron

Table ......................................................................................................................... precision-ground cast iron

Table insert ................................................................................................................................................ MDF

Column ....................................................................................................................................................... steel

Base ..................................................................................................................................................... cast iron

Table:

Table size ........................................................................................................... 14” L x 19” W (356 x 483 mm)

Table slots (4) .................................................................................................... 3-1/8”L x 5/8” W (79 x 15 mm)

Table T-slots (2) ................................................................................................... 1/2” W x 5/8” D (13 x 15 mm)

Distance between T-slots (centers)........................................................................................ 10-5/8” (270 mm)

Table tilt.................................................................................................................................... 90 deg. L and R

Table rotation around column .............................................................................................................. 360 deg.

Table elevating system ...................................................................................................... worm gear with rack

Table insert ........................................................................................................... 3-3/4” x 3-3/4” (95 x 95 mm)

Recommended maximum weight on table .................................................................................... 66 lb. (30 kg)

........................................................................................................................ 15 A

Base and Column:

Base size............................................................................................................ 20” L x 13” W (507 x 328 mm)

Base working surface ............................................................................... 8-1/2” L x 10-1/2” W (217 x 271 mm)

Base slots (2) ........................................................................................................ 5/8” W x 7” L (15 x 178 mm)

Distance between base slots (centers) .................................................................................... 5-1/8” (130 mm)

Column diameter ...................................................................................................................... 3-5/32” (80 mm)

Dimensions and Weights:

Overall dimensions, assembled ........................................... 28-1/2” L x 19” W x 66” H (723 x 483 x 1679 mm)

Shipping dimensions ............................................... 58” L x 24-7/16” W x 12-13/16” H (1475 x 620 x 325 mm)

Net weight (approximate) .............................................................................................................. 187 lb (85kg)

Shipping weight (approximate)...................................................................................................... 198 lb (90kg)

L = length; W = width; H = height

Subject to local and national electrical codes.

The specified values are emission levels and are not necessarily to be seen as safe operating levels. As workplace

conditions vary, this information is intended to allow the user to make a better estimation of the hazards and risks involved only.

Swing is twice the distance from column to spindle center (i.e., the maximum diameter of workpiece that can be

drilled to its center).

5.1 Base mounting holes for JDP-17

Figure 1: Base mounting holes

The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations.

6.0 Setup and assembly

Read and understand all

assembly instructions before attempting assembly. Failure to comply may cause serious injury.

6.1 Unpacking

Separate all parts from the packing material. Check each part against sect. 6.2 Shipping contents and make certain that all items are accounted for before discarding any packing material. Report any shortages or shipping damage to your JET distributor.

Exposed metal surfaces on the drill press have been factory-coated with a protectant. Remove this with a soft rag moistened with a light solvent, such as kerosene or WD-40 pad, and do not use gasoline, paint thinner or acetone – these will damage plastic components and painted surfaces.

After assembly, exposed metal surfaces on the drill press should be periodically coated with a light application of paste wax or other rust-protectant.

6.2 Shipping contents

Refer to Figures 2 and 3.

1 Head assembly – A 1 Table and bracket assembly – B 1 Table insert – C 1 Base – D 1 Column and foot assembly – E 1 Rack – F 1 Owner’s manual (not shown) 1 Warranty card (not shown)

Hardware package (JDP17-HP2):

1 Drift Key – HP1 1 Table locking wrench 24mm – HP2 1 Handle, column lock – HP3 1 Handle, table elevating – HP4 3 Downfeed handles – HP5 1 Worm – HP6 3 Hex keys, 3/4/5/6mm – HP7 4 Socket head cap screws, M8x50 – HP8 4 Flat washers, 8mm – HP9 1 Chuck key – HP10 1 Chuck 5/8” – HP11 1 Arbor – HP12

. Do not use an abrasive

Figure 2: Contents of shipping container

(JDP-15F column shown)

Figure 3: Hardware Package (p/n JDP17-HP2)

6.3 Additional tools required for

assembly

(not provided)

Rubber mallet (or hammer and wood block) 13mm wrench (for table pin nut) Cross-point (Phillips) screwdriver

6.4 Location

The drill press should be placed in a dry area, with a level floor and good lighting. Provide enough space around drill press to allow for operations and any adjustments or servicing.

6.5 Assembly

Do not connect drill press to

power source until machine has been fully assembled.

1. Place the base upon a level floor. It may be secured to the floor with lag screws (not provided) through the two holes in the base. Refer to Figure 1 for hole spacing.

If you do not wish permanent attachment to the floor, the drill press can be bolted to a plywood panel which will serve as an expanded base and further stabilize the machine. Use a high grade of plywood (not particle board) at least 3/4" thick. It should be large enough to prevent vibration, sliding or moving of drill press during operation. Do not use a mobile base with this machine.

2. Make sure the set screw (Figure 4) is tight against the column. Tighten further if needed, using a 5mm hex key.

Figure 4

3. Lay the column assembly down on an elevated surface (such as the included polystyrene packaging). Attach base to column foot with four M8x50 socket head cap screws and four 8mm flat washers (HP8/HP9, Figure 5), using a 6mm hex key. NOTE: Align base and foot so that their edges are flush.

4. Tighten screws firmly.

Figure 5

5. Set column assembly upright.

6. Insert the worm shaft (HP6, Figure 6) through the hole in the table bracket as far as it will go, meshing the worm with the teeth on the gear.

Figure 6

7. Position rack (F, Figure 7) into the sl ot in table bracket. The longer flat portion of the rack should be at the top, the short flat portion at the bottom. Mesh the rack teeth with the worm gear in the table bracket.

8. W ith the aid of a second person, hold the rack in the slot, while setting the table bracket over the top of the column. Then slide table bracket and rack together down the column until the lower end of the rack rests in the lip of the holder, as shown in Figure 7.

+ 19 hidden pages