#717600 In-Line Cyclonic Chip Separator
Assembly and Specifications
Shipping contents:
#717600 – Chip Separator only
1 Chip separator
1 Assembly & specifications sheet
1 Mounting template
1 Product registration card
2 Wire hose clamps 4 in.
6 Washer head screws 1/4x3/4 in.
6 Flanged hex nuts 1/4 in.
1 Gasket
1 Wrench
#717650 – Chip Separator + JET collection bin
1 717600 Chip Separator, all parts listed above
1 Steel collection bin
4 Casters
1 Handle
2 Pan head screws 1/4x1/2 in.
Assembly of JET Collection Bin
Turn bin upside-down and install casters by screwing them
into the threaded holes. Tighten the nuts against the bin
using the provided wrench.
Turn bin upright and install handle with 2 screws into
threaded holes on side of bin.
Assembly of Chip Separator
Connect 4-inch diameter hoses (not included) from your
woodworking machine and from your dust collection system.
Secure these with the provided wire clamps. See Figure 2.
Figure 1: Types of compatible containers (JET bin shown
at right)
Woodworking machine and dust
collector must be turned off while installing chip
separator.
If using the JET dust bin, the center opening and screw
holes are predrilled.
If using a different container than the JET bin (see Figure
1), use the provided paper template to drill holes in the lid.
Drill six 3/8-in. (9mm) holes for the screws, and cut out a
center hole 5-in. (126mm) in diameter.
Place the gasket between separator and bin, and insert the
screws from beneath lid. Secure with flanged hex nuts. See
Figure 2.
Figure 2: Hoses not provided; shown with JET bin
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-413400
Ph.: 800-274-6848 Edition 1 08/2020
www.jettools.com Copyright © 2020 JET
Specifications
Inlet and outlet diameter 4 in. (101.6 mm)
Bin connection diameter 5 in. (127 mm)
JET bin capacity n/a 20 gal.
Overall size L x W x H
Main materials
Shipping dimensions L x W x H
Weights
n/a = not applicable
Net 3.5 lbs. (1.6 kgs) 18.7 lbs. (8.5 kgs)
Shipping 4.85 lbs. (2.2 kgs) 24.7 lbs. (11.2 kgs)
15-3/4 x 8-21/32 x 11 in.
17-1/8 x 9-27/32 x 12 in.
717600
(Separator)
(400 x 220 x 281 mm)
PC (polycarbonate)
(435 x 250 x 305 mm)
(Separator + JET bin)
20-7/8 x 16-1/2 x 30-1/2 in.
Bin: Steel; acrylic window
19-11/16 x 19-11/16 x 23-7/32 in.
717650
(531 x 420 x 775 mm)
PC (polycarbonate)
(500 x 500 x 590 mm)
Specifications were current at time of publication, but because of our policy of continuous improvement, JET reserves the right
to change specifications at any time and without prior notice, without incurring obligations.
To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having
the Model Number and Serial Number of your product available when you call will allow us to serve you quickly and accurately.
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET.
Individual parts are available in a Hardware Package. See shipping contents for part numbers.
WARNING: This product can expose you to chemicals including lead which is known to the State of California to cause
cancer and birth defects or other reproductive harm. For more information go to http://www.p65warnings.ca.gov.
WARNING: Drilling, sawing, sanding or machining wood products generates wood dust and other substances known to the
State of California to cause cancer. Avoid inhaling dust generated from wood products or use a dust mask or other safeguards
for personal protection. Wood products emit chemicals known to the State of California to cause birth defects or other
reproductive harm. For more information go to http://www.p65warnings.ca.gov/wood.
2
717600 Cyclone Separator Assembly – Parts Breakdown
Index No. Part No. Description Size Qty
1 ................ 216-A002-02 .............. Chip Separator ......................................................... ...................................... 1
2 ................ 512-B006 ................... Wire Hose Clamp ..................................................... 4” ................................... 2
3 ................ 528-E016 ................... Flanged Hex Nut ...................................................... 1/4”-20 ........................... 6
4 ................ 516-B143 ................... Gasket ..................................................................... ...................................... 1
6 ................ 504-F003 ................... Washer Head Screw ................................................ 1/4”-20x3/4” ................... 6
11 .............. 530-B010 ................... Wrench .................................................................... 10-14mm ....................... 1
.................. 600HP ....................... Hardware Package (includes #2 thru 4, 6, 11) ........ ........................................
3
717650 Cyclone Separator with Dust Collection Bin Assembly – Parts Breakdown
Index No. Part No. Description Size Qty
1 ................ 216-A002-02 .............. Chip Separator ........................................................ ...................................... 1
2 ................ 512-B006 ................... Wire Hose Clamp ..................................................... 4” ................................... 2
3 ................ 528-E016 ................... Flanged Hex Nut ...................................................... 1/4”-20 ........................... 6
4 ................ 516-B143 ................... Gasket ..................................................................... ...................................... 1
5 ................ 225-D172D-01 ........... Bin Lid ...................................................................... ...................................... 1
6 ................ 504-F003 ................... Washer Head Screw ................................................ 1/4”-20x3/4” ................... 6
7 ................ 225-D173D-01 ........... Steel Dust Collection Bin ......................................... ...................................... 1
8 ................ 516-F011 ................... Handle ..................................................................... ...................................... 1
9 ................ 504-B016 ................... Pan Head Screw ...................................................... 1/4”-20x1/2” ................... 2
10 .............. 514-A006 ................... Caster ...................................................................... ...................................... 4
11 .............. 530-B010 ................... Wrench .................................................................... 10-14 ............................. 1
.................. 600HP ....................... Hardware Package (includes #2 thru 4, 6, 11) ........ ........................................
.................. 650HP ....................... Hardware Package (includes #8,9,10) ..................... ........................................
4
Loading...