JET HVBS-8-DMW, HVBS-10-DMW, HVBS-10-DMWC Operating Instructions and Parts Manual
Operating Instructions and Parts Manual
This .pdf document is bookmarked
Portable Dual Mitering Band Saws
Models HVBS-8-DMW, HVBS-10-DMW, HVBS-10-DMWC
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-424460
Ph.: 800-274-6848 Edition 8 06/2020
www.jettools.com Copyright © 2017 JET
Model HVBS-10-DMWC shown
For HVS-8-DMW after serial no. 1701BG00017
For HVS-10-DMW after serial no. 1701BK00017
1
1.0 IMPORTANT SAFETY
INSTRUCTIONS
WARNING – To reduce risk of injury:
1. Read and understand the entire owner's
manual before attempting assembly or
operation.
2. Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
3. Replace the warning labels if they become
obscured or removed.
4. This band saw is designed and intended for use
by properly trained and experienced personnel
only. If you are not familiar with the proper and
safe operation of a band saw, do not use until
proper training and knowledge have been
obtained.
5. Do not use this machine for other than its
intended use. If used for other purposes, JET
disclaims any real or implied warranty and holds
itself harmless from any injury that may result
from that use.
6. Always wear ANSI Z87.1 approved safety
glasses or face shield while using this band
saw. (Everyday eyeglasses only have impact
resistant lenses; they are not safety glasses.)
7. Before operating this machine, remove tie,
rings, watches and other jewelry, and roll
sleeves up past the elbows. Do not wear loose
clothing. Confine long hair. Non-slip footwear or
anti-skid floor strips are recommended. Do not
wear gloves.
8. Wear ear protectors (plugs or muffs) if noise
exceeds safe levels.
9. Make certain the switch is in the OFF position
before connecting the machine to the power
supply.
10. Make certain the machine is properly grounded.
11. Make all machine adjustments or maintenance
with the machine unplugged from the power
source.
12. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and adjusting
wrenches are removed from the machine
before turning it on.
13. Keep safety guards in place at all times when
the machine is in use. If removed for
maintenance purposes, use extreme caution
and replace the guards immediately after
completion of maintenance.
14. Check damaged parts. Before further use of the
machine, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced.
15. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
16. Keep the floor around the machine clean and
free of scrap material, oil and grease.
17. Keep visitors a safe distance from the work
area. Keep children away.
18. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
19. Give your work undivided attention. Looking
around, carrying on a conversation and “horseplay” are careless acts that can result in serious
injury.
20. Maintain a balanced stance at all times so that
you do not fall into the blade or other moving
parts. Do not overreach or use excessive force
to perform any machine operation.
21. Use the right tool at the correct speed and feed
rate. Do not force a tool or attachment to do a
job for which it was not designed. The right tool
will do the job better and more safely.
22. Use recommended accessories; improper
accessories may be hazardous.
23. Maintain tools with care. Keep saw blades
sharp and clean for the best and safest
performance. Follow instructions for lubricating
and changing accessories.
24. Maintain proper adjustment of blade tension,
blade guides and thrust bearings.
25. Turn off the machine before cleaning. Use a
brush to remove chips or debris — do not use
your hands.
26. Do not stand on the machine. Serious injury
could occur if the machine tips over.
27. Never leave the machine running unattended.
Turn the power off and do not leave the
machine until it comes to a complete stop.
28. Remove loose items and unnecessary work
pieces from the area before starting the
machine.
2
29. Never hand hold the material. Always use the
vise and clamp it securely.
30. Be sure that blade is not in contact with
workpiece when motor is started. Allow motor to
come up to speed before bringing blade into
contact with workpiece.
31. Avoid contact with coolant, especially guarding
your eyes.
32. Never reach around or over saw blade during
operation. Keep hands and fingers away from
blade area.
33. Do not remove jammed pieces until blade has
stopped.
34. Don’t use in dangerous environment. Don’t use
power tools in damp or wet location, or expose
them to rain. Keep work area well lighted.
35. Use proper extension cord. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will
draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and
overheating. Table 2 (sect. 6.3) shows correct
size to use depending on cord length and
nameplate ampere rating. If in doubt, use the
next heavier gage. The smaller the gage
number, the heavier the cord.
Familiarize yourself with the following safety notices used in this manual:
WARNING: This product can expose you to
chemicals including titanium dioxide which is
known to the State of California to cause cancer,
and lead which is known to the State of
California to cause cancer and birth defects or
other reproductive harm. For more information
go to http://www.p65warnings.ca.gov.
WARNING: Some dust, fumes and gases
created by power sanding, sawing, grinding,
drilling, welding and other construction activities
contain chemicals known to the State of
California to cause cancer and birth defects or
other reproductive harm. Some examples of
these chemicals are:
lead from lead based paint
crystalline silica from bricks, cement and
other masonry products
arsenic and chromium from chemically
treated lumber
Your risk of exposure varies, depending on how
often you do this type of work. To reduce your
exposure to these chemicals, work in a wellventilated area and work with approved safety
equipment, such as dust masks that are
specifically designed to filter out microscopic
particles. For more information go to
http://www.p65warnings.ca.gov/ and http://www.
p65warnings.ca.gov/wood.
This means that if precautions are not heeded, it may result in minor injury and/or possible
machine damage.
This means that if precautions are not heeded, it may result in serious, or possibly even fatal,
injury.
1.1 On-off switch padlock
To avoid accidental starting by young children or others not qualified to use the tool, the use of a padlock (not
provided) is required.
To lock out the on-off switch (Figure 2-1):
1. Open padlock.
2. Insert through hole in switch guard.
3. Close padlock.
4. Store key in a safe place out of the reach of
children.
Figure 1-1
3
2.0 Table of contents
Section Page
1.0 IMPORTANT SAFETY INSTRUCTIONS ....................................................................................................... 2
1.1 On-off switch padlock ................................................................................................................................. 3
2.0 Table of contents ............................................................................................................................................ 4
3.0 About this manual .......................................................................................................................................... 5
4.0 Specifications for HVBS-DMW series Band Saws ......................................................................................... 6
5.0 Setup and assembly ....................................................................................................................................... 8
5.1 Shipping contents ....................................................................................................................................... 8
5.2 Unpacking and cleanup .............................................................................................................................. 8
5.3 Assembly (all models) ................................................................................................................................ 8
5.4 Additional assembly (10-inch models only) ................................................................................................ 8
6.0 Electrical connections .................................................................................................................................... 8
6.1 GROUNDING INSTRUCTIONS ................................................................................................................. 9
6.2 Voltage conversion ..................................................................................................................................... 9
6.3 Extension cords ........................................................................................................................................ 10
7.0 Adjustments ................................................................................................................................................. 10
7.1 Handle adjustment ................................................................................................................................... 10
7.2 Bow swivel ................................................................................................................................................ 10
7.3 Blade speed adjustment ........................................................................................................................... 10
7.4 Blade guide arms .................................................................................................................................... 11
7.5 Blade replacement ................................................................................................................................... 11
7.6 Blade guide bearings ................................................................................................................................ 12
7.7 Blade tension and tracking ....................................................................................................................... 12
7.8 Blade-to-table squareness ....................................................................................................................... 13
7.9 Setting feed rate ....................................................................................................................................... 13
7.10 Counterbalance spring ........................................................................................................................... 14
7.11 Vertical bow position .............................................................................................................................. 14
7.12 Auto shut-off adjustment ........................................................................................................................ 14
7.13 Vise positioning ...................................................................................................................................... 15
7.14 Work stop ............................................................................................................................................... 15
8.0 Operation ..................................................................................................................................................... 15
8.1 Blade selection ......................................................................................................................................... 15
8.2 Blade break-in .......................................................................................................................................... 15
8.3 General operating procedure ................................................................................................................... 16
8.4 Evaluating cutting efficiency ..................................................................................................................... 16
9.0 User-maintenance ........................................................................................................................................ 17
9.1 Lubrication ................................................................................................................................................ 17
9.2 Coolant level (HVBS-10DMW-C) ............................................................................................................. 17
9.3 Additional servicing .................................................................................................................................. 17
10.0 Troubleshooting HVBS-DM series Band Saws .......................................................................................... 18
11.0 Replacement Parts ..................................................................................................................................... 19
11.1.1 HVBS-8-DMW Bow Assembly – Exploded View ................................................................................. 20
11.1.2 HVBS-8-DMW Table Assembly – Exploded View ............................................................................... 21
11.1.3 HVBS-8-DMW Motor and Support Arm Assembly – Exploded View .................................................. 22
11.1.4 HVBS-8-DMW Vise and Table Assembly – Exploded View ................................................................ 23
11.1.5 HVBS-8-DMW Base Assembly – Exploded View ................................................................................ 23
11.1.6 HVBS-8-DMW – Parts List .................................................................................................................. 24
11.2.1 HVBS-10-DMW/DMWC Bow Assembly – Exploded View .................................................................. 29
11.2.2 HVBS-10-DMW/DMWC Table Assembly – Exploded View ................................................................ 30
11.2.3 HVBS-10-DMW/DMWC Motor and Support Arm Assembly – Exploded View .................................... 31
11.2.4 HVBS-10-DMW/DMWC Vise and Table Assembly – Exploded View ................................................. 32
11.2.5 HVBS-10-DMW/DMWC Base Assembly – Exploded View ................................................................. 33
11.2.6 HVBS-10-DMW/DMWC – Parts List .................................................................................................... 34
12.0 Electrical Connections for HVBS-DMW Band Saws .................................................................................. 39
13.0 Warranty and service ................................................................................................................................. 40
4
3.0 About this manual
This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model
HVBS-DMW series Portable Band Saw. This manual contains instructions on installation, safety precautions,
general operating procedures, maintenance instructions and parts breakdown. Your machine has been designed
and constructed to provide consistent, long-term operation if used in accordance with the instructions as set forth
in this document.
If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our
web site: www.jettools.com.
Retain this manual for future reference. If the machine transfers ownership, the manual should accompany it.
Read and understand the entire contents of this manual before attempting assembly or
operation! Failure to comply may cause serious injury!
Register your product using the mail-in card provided, or register online: http://www.jettools.com/us/en/serviceand-support/warranty/registration/
5
4.0 Specifications for HVBS-DMW series Band Saws
Model number
HVBS-8-DMW HVBS-10-DMW HVBS-10-DMWC
Stock number 424460 424463 424465
Motor and Electricals
Motor type TEFC induction
Horsepower 3/4 HP (0.56 kW) 1 HP (0.75 kW) 1 HP (0.75 kW)
Phase 1
Voltage 115 / 230V (prewired 115V) 3
Cycle 60 Hz
Listed FLA (full load amps) 9 / 4.5 14 / 7
Motor speed 1720 RPM
Start capacitor 300MFD 125VAC
Running capacitor
20F 250VAC 30F 250VAC
Power cord SJT 14AWGx3C, 6ft.
Power plug installed 115V
Power transfer Step pulleys with v-belt, to gear reducer box
Gear ratio 1:40 1:50
Recommended circuit size 1 15A 20A (115V), 15A (230V)
Sound emission without load 2 70 dB 75 dB
Coolant pump
n/a n/a 1/8HP 2P 1PH 0.78/0.4A
115/230V
Capacities
Round
90 deg. 8 in. (200 mm) 10 in. (250 mm)
+/-45 deg. 6 in. (150 mm) 6-1/2 in. (165 mm)
90 deg. 6-1/2 x 8 in.
8 x 9 in. (200 x 228 mm)
(165 x 200 mm)
Tubing &
Solids
Rectangle
+45 deg. 7 x 5-1/2 in.
(175 x 137 mm)
-45 deg. 6 x 5-1/2 in.
(150 x 137 mm)
90 deg. 7 x 7 in.
8 x 5 in. (200 x 127 mm)
8 x 5-1/2 in. (200 x 140 mm)
8 x 8 in. (200 x 200 mm)
(175 x 175 mm)
Square
+45 deg. 5-1/2 x 5-1/2 in.
(137 x 137 mm)
-45 deg. 5-1/2 x 5-1/2 in.
5-1/2 x 5-1/2 in. (137 x 137 mm)
5 x 5 in. (127 x 127 mm)
(137 x 137 mm)
Vertical cutting capacity
12 x 8 in.
(305 x 200 mm)
13 x 10 in. (330 x 254 mm)
Bow swivel +/- 45 deg.
Gearbox oil capacity 330 cc (0.07 gal.) 430 cc (0.095 gal.)
Coolant capacity n/a n/a 32 L (7 gal.)
Blade
Blade type and size 6/10T, 3/4 x 0.035 x 102.9 in.
(19 x 0.9 x 2616 mm)
5/8T, 1 x 0.035 x 120 in.
(27 x 0.9 x 3048 mm)
Blade speeds 64, 132, 247 SFPM (19.5, 40, 75 mpm)
Main materials
Bow and stand steel
Blade wheels cast iron
Tires rubber
Pulleys cast iron
Table cast iron and aluminum
6
HVBS-8-DMW HVBS-10-DMW HVBS-10-DMWC
Dimensions
Blade wheel diameter 37-1/8 in. (943 mm) 41.73 in. (1060 mm)
Distance table from floor 27-1/2 in. (697 mm) 29 in. (728 mm)
Overall assembled (LxWxH) 54 x 25 x 42 in.
(1381 x 639 x 1060mm)
Shipping dimensions (LxWxH) 56.3 x 27.6 x 43.3 in.
(1430 x700 x 1100 mm)
63 x 27 x 45 in.
(1597.9x676x1144mm)
61 x 29.6 x 45.5 in.
(1550 x 750 x 1155 mm)
70 x 35 x 45 in.
(1784 x 878 x 1144mm)
Weights
Net weight 390 lb. (177 kg) 511 lb. (232 kg)
Shipping weight 454 lb. (206 kg) 582 lb. (264 kg)
Table 1
1
subject to local and national electrical codes.
2
The specified values are emission levels and are not necessarily to be seen as safe operating levels. As workplace
conditions vary, this information is intended to allow the user to make a better estimation of the hazards and risks
involved only.
3
Conversion to 230V operation requires separate purchase of 230V magnetic switch. See parts list..
L = length, W = width, H = height
n/a = not applicable
The specifications in this manual were current at time of publication, but because of our policy of continuous
improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring
obligations.
7
5.0 Setup and assembly
Read and understand all
instructions before attempting assembly. Band
Saw must be disconnected from power during
all assembly procedures. Failure to comply may
cause serious injury.
5.1 Shipping contents
1 Band saw
2 Wheels
1 Work stop assembly
1 Vertical cutting platform
1 Chip bin (10” models only)
4. If closer reach is needed toward blade, insert
small rod (A
flat.
Figure 5-2: installing work stop
) and tighten with wrench on rod
4
5.2 Unpacking and cleanup
1. Inspect all contents for shipping damage.
Compare contents of shipping carton with
contents list in this manual. Report any damage
or part shortages to your distributor.
2. Do not discard packing material until saw is
assembled and running properly.
3. Remove rust protectant from exposed surfaces,
such as table, vise assembly, etc., with a clean
rag and a cleaner/degreaser. Apply a light coat
of oil on these surfaces to inhibit rust.
5.3 Assembly (all models)
1. Remove any straps or braces holding saw to
pallet, and carefully raise saw from pallet, using
properly rated lifting equipment (hoist or forklift)
with straps.
2. Remove fasteners from the wheel flanges of
carriage. Position wheel between flanges, and
insert hex bolt with spacer on each side, as
shown in Figure 6-3. Secure with hex nut and
washer.
5.4 Additional assembly (10-inch
models only)
Install chip bin at back of saw base. (See Figure 1110 and manual cover photo for positioning.)
5.4.1 Coolant preparation (HVBS-10-
DMWC only)
Coolant tray must be filled high
enough to submerge pump impeller. Failure to
do this may damage pump. Periodically check
and maintain coolant level.
Use of a water-soluble coolant will increase cutting
efficiency and prolong blade life. Do not use black
cutting oil as a substitute. Change cutting oil often
and follow manufacturer’s instructions as to its uses
and precautions.
1. Disconnect machine from power source.
2. Pour approximately 32 L (7 gal) of coolant into
coolant tray.
3. Make sure coolant hoses are properly
connected at each end.
When cutting magnesium,
never use soluble oils or emulsions (oil-water
mix) as water will greatly intensify any
accidental magnesium chip fire. Consult your
coolant supplier for coolant recommendations
when cutting magnesium.
Figure 5-1: installing wheel
3. Install work stop rod (A
beneath table and tighten set screw. Install
work stop onto rod threads by rotating collar
). Secure position of work stop by tightening
(A
2
set screw (A
) onto rod flat.
3
, Figure 5-2) into hole
1
6.0 Electrical connections
Electrical connections must be
made by a qualified electrician in compliance
with all relevant codes. This machine must be
properly grounded to help prevent electrical
shock and possible fatal injury.
The HVBS-DMW series Band Saws are rated at
115/230V power, and are pre-wired for 115 volt. The
band saw comes with a plug designed for use on a
8
circuit with a grounded outlet that looks like the one
pictured in A, Figure 6-1.
Before connecting to power source, be sure switch
is in off position.
It is recommended that the HVBS-8DMW be
connected to a dedicated 15 amp circuit with circuit
breaker or fuse. If connected to a circuit protected
by fuses, use time delay fuse marked “D”.
It is recommended that the HVBS-10DMW, when
operated on 115V, be connected to a dedicated 20
amp circuit with circuit breaker or fuse. When
operated on 230V power, connect it to a dedicated
15 amp circuit with circuit breaker or fuse. If
connected to a circuit protected by fuses, use time
delay fuse marked “D”.
NOTE: Local codes take precedence over
recommendations.
6.1 GROUNDING INSTRUCTIONS
This machine must be grounded. In the event of a
malfunction or breakdown, grounding provides a
path of least resistance for electric current to reduce
the risk of electric shock. This tool is equipped with
an electric cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into a matching outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify the plug provided - if it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The
conductor with insulation having an outer surface
that is green with or without yellow stripes is the
equipment-grounding conductor. If repair or
replacement of the electric cord or plug is
necessary, do not connect the equipment-grounding
conductor to a live terminal.
Check with a qualified
electrician or service personnel if the grounding
instructions are not completely understood, or if
in doubt as to whether the tool is properly
grounded. Failure to comply may cause serious
or fatal injury.
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept
the tool's plug.
Repair or replace damaged or worn cord
immediately.
When operated at 115-volt, this tool is intended for
use on a circuit that has an outlet that looks like the
one illustrated in A, Figure 6-1. An adapter, shown
in B and C, may be used to connect this plug to a
2-pole receptacle as shown in B if a properly
grounded outlet is not available. The temporary
adapter should be used only until a properly
grounded outlet can be installed by a qualified
electrician. The green-colored rigid ear, lug, and the
like, extending from the adapter must be connected
to a permanent ground such as a properly grounded
outlet box. Note: In Canada, the use of a temporary
adaptor is not permitted by the Canadian Electrical
Code, C22.1.
Figure 6-1: grounding
When operated at 230-volt, this tool is intended for
use on a circuit that has an outlet that looks like the
one illustrated in D, Figure 6-1. The tool has a
grounding plug that looks like the plug illustrated in
D. Make sure the tool is connected to an outlet
having the same configuration as the plug. No
adapter is available or should be used with this tool.
If the tool must be reconnected for use on a different
type of electric circuit, the reconnection should be
made by qualified service personnel; and after
reconnection, the tool should comply with all local
codes and ordinances.
6.2 Voltage conversion
The Band Saw is prewired for 115 volt. To change
incoming leads for 230 volt operation:
1. Open main motor junction box cover, and
change leads based on wiring diagram inside
cover. This diagram is also shown in Figure 6-
2. (NOTE: In case of discrepancy, diagram on
machine takes precedence.) Reinstall cover.
2. Change out 115V magnetic switch with 230V
magnetic switch (separate purchase, see parts
list for number).
3. (Model HVBS-10DMWC only: Remove coolant
pump junction box cover, and change incoming
leads for coolant pump, based on diagram
shown in Figure 6-2. Reinstall cover.)
Figure 6-2: voltage conversion
9
4. The plug on end of power cord must be
replaced with a UL/CSA listed plug rated for 230
volt operation.
6.3 Extension cords
The use of extension cords is discouraged; try to
position machines near the power source. If an
extension cord is necessary, make sure it is in good
condition. When using an extension cord, be sure to
use one heavy enough to carry the current your
product will draw. An undersized cord will cause a
drop in line voltage resulting in loss of power and
overheating.
Table 2 shows correct size to use depending on
cord length and nameplate ampere rating. If in
doubt, use the next heavier gauge. The smaller the
gauge number, the heavier the cord.
Ampere
Rating
More
Than
00 06 18 16 16 14
06 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12
Not
More
Than
Table 2: Extension cord recommendations
Volts
120
240
AWG
Total length of
cord in feet
25
50
100
50
100
200
Not
Recommended
150
300
7.0 Adjustments
Always disconnect band saw
from power source before making adjustments,
unless indicated otherwise.
Figure 7-1
7.3 Blade speed adjustment
1. Disconnect band saw from power source.
2. Place bow in horizontal position.
3. Open pulley box and turn handle (D, Figure 7-
2) counterclockwise to release tension on drive
belt.
4. Move belt to desired pulley combination. Refer
to chart inside pulley box (reproduced in Figure
7-3).
5. Turn handle (D) clockwise to tension belt.
Finger pressure on belt midway between
pulleys should cause approximately 1/2-inch
deflection. Do not overtighten belt.
6. Close pulley box before operating.
General rule for band saw blade speed: The harder
the material being cut, the slower the blade speed.
Refer to a machinist’s handbook for recommended
speeds for specific materials.
7.1 Handle adjustment
The plastic handles for swivel (A, Figure 7-1) and
blade guide arm positioning are adjustable to
prevent obstruction of other parts. Pull out on handle
and rotate it on pin, then release it, allowing it to
resettle on pin.
7.2 Bow swivel
1. Disconnect band saw from power source.
2. Loosen handle (A, Figure 7-1) and rotate bow
to desired angle on scale (B).
3. Confirm accuracy of angle by cutting a test
piece or using an angle measuring device
against blade and fixed vise jaw. If scale needs
adjustment, adjust pointer.
4. Verify accuracy of 45-degree left and right stop
screws (C). Adjust if needed.
5. Tighten handle (A) before operating saw.
10
Figure 7-2: blade speed adjustment
Figure 7-3: blade speeds (rounded off)
7.4 Blade guide arms
1. Disconnect band saw from power source.
2. The fixed blade guide arm (E, Figure 7-4)
should be positioned as close to work area as
possible, without interfering when bow is
swiveled to an angle. Loosen screw (E
slide arm as needed. Tighten screw before
operating. (Once the fixed guide arm is
properly positioned, it can generally remain in
that position for all operations.)
3. The movable blade guide arm (F) should be as
close as possible without interference to
material being cut. Loosen handle (F
slide arm as needed. Retighten handle before
operating.
) and
1
) and
1
that they straddle the work, severe damage to
workpiece and blade can result.
1. Disconnect band saw from power source.
2. Raise bow to convenient position.
3. Open wheel guards and prop them open with
the attached rods (G, Figure 7-5). Remove red
blade guards (H).
It is essential that red blade
guards be re-installed after new blade has
been fitted. Failure to comply may cause
serious injury.
Figure 7-5
4. Back off the eccentric bearing guides (see sect.
7.6 for detailed instructions).
5. Release tension on blade by turning tension
handle (P, Figure 7-8) counterclockwise.
Remove blade. (Use leather gloves when
handling sharp blades).
6. Install new blade between blade guide
assemblies and around each wheel. Make sure
blade teeth are pointing in proper direction. See
Figure 7-6. If they are not, twist blade insideout.
7. Increase blade tension just enough to hold
blade on wheels. Make sure back of blade rests
lightly against shoulder of both wheels. Twist
blade slightly to allow it to slip into guides.
Figure 7-4: blade guide arm adjustment
7.5 Blade replacement
A general-use variable-tooth blade is provided with
this band saw.
Choice of blade pitch is governed by thickness of
workpiece: the thinner the workpiece, the more
teeth advised. A minimum of 3 teeth should engage
workpiece at all times. If blade teeth are so far apart
Figure 7-6
11
8. Install red blade guards.
9. Tension blade fully (see sect. 7.7)
10. Place two to three drops of lightweight oil on
blade.
11. Adjust blade guide bearings (see sect. 7.6).
12. Connect machine to power source and operate
it to make sure blade is tracking properly (sect
7.7.2).
13. Follow blade break-in procedures (sect. 8.2).
7.6 Blade guide bearings
1. Disconnect machine from power source.
2. Loosen screw (J
bearing (J
inches from back edge of blade. Tighten screw
).
(J
1
3. Inside bearing (K
rotates on an eccentric shaft. Loosen nut (K
and rotate lower nut (K
bearing to a clearance of 0.001 inches from
blade. Retighten nut (K
4. Repeat above steps for opposite blade guide
assembly.
Figure 7-7: blade guide bearings
, Figure 7-7) and adjust back
1
) to approximately 0.002 to 0.003
2
) is fixed. Outside bearing (K2)
1
) to adjust eccentric
4
).
3
3
4. Return blade guide arm to operating position.
Note: A new blade should be re-checked for proper
tension after a few minutes’ operation.
7.7.2 Tracking
Blade tracking adjustment
requires operating saw with wheel guards open.
This adjustment must be completed by qualified
persons only. Failure to comply may cause
serious injury.
Blade tracking has been set by manufacturer.
Adjustment is rarely required when blade is used
properly and is correctly welded.
Tracking is set properly when blade runs without
shifting on the wheels, and back of blade lightly
touches shoulder of wheels.
If adjustment is required:
)
1. Confirm that blade tension is properly set.
2. Set belt position to slowest speed.
3. Raise bow to convenient position and open
wheel guards.
While performing the
following steps, keep blade from rubbing
excessively on wheel shoulder. Excessive
rubbing will damage wheel and/or blade.
4. Run saw and observe blade – it should run next
to, but not tightly against, wheel shoulder.
5. If blade is not tracking properly, loosen either of
two hex nuts (N
6. Turn set screw (N
, Figure 7-8).
1
) with hex wrench, while
2
observing blade tracking on wheel. NOTE: This
adjustment is sensitive; start with 1/4-turns on
set screw and allow blade to respond to
changes.
7.7 Blade tension and tracking
Refer to Figure 7-8.
7.7.1 Tension
1. Disconnect machine from power source.
2. Loosen movable blade guide arm and slide it
away from the other arm as far as possible.
3. Turn blade tension handle (P, Figure 7-8)
clockwise to tighten blade. Pluck the blade with
your finger; a tensioned blade will emit a
“twang” sound. As experience with the saw is
gained, operator may develop a better feel for
how tight to set a particular blade.
For precise measurement, use a blade tension
gauge (not provided). Hard-back blades are
generally tensioned at about 25,000 PSI (1757
2
kg/cm
); bi-metal blades at about 35,000 PSI
2
(2460 kg/cm
).
Keep fingers clear of blade
and wheel to avoid injury.
7. Test the setting by placing a six-inch length of
paper between blade and wheel. The paper
should not be cut as it passes between wheel
shoulder and blade.
8. Turn set screw (N
) a small amount. Repeat
2
insertion of paper between the shoulder and the
blade until paper is cut into two pieces.
NOTE: You may have to repeat the check with
the paper several times before blade and
shoulder cut the paper into two pieces. Do not
hurry the adjustment. Patience and accuracy
here will pay off with better, more accurate,
quieter cutting and longer machine and blade
life.
9. When paper is cut, back off set screw slightly.
This assures that blade is not pushing
excessively against wheel shoulder.
12
Loading...