Jensen PowerPlus 682, PowerPlus 652, PowerPlus 652C User Manual

PowerPlus Speakers

Installation Manual

PowerPlus 525

PowerPlus 652

PowerPlus 652C

PowerPlus 682

PowerPlus 693

INTRODUCTION

Thank you!

Para obtener instrucciones en Español, diríjase a la página 7. Pour des instructions en Francais, référez-vous à la page 13.

Thank you for purchasing this quality Jensen product! PowerPlus speaker system is the ultimate complement to your car stereo system. cones, black foam surrounds, tweeters with acoustic equalizer, and neodymium magnets, offers unparalleled audio reproduction. The PowerPlus series will deliver the natural sound you have come to expect from Jensen.

The speaker system should be connected to your car radio or an additional car stereo amplifier, which we recommend for even better sound quality. Technical data plus installation tips and further advice are contained in this instruction manual.

The PowerPlus series, featuring polypropylene

Your new

Highlighted Features

Warp resistant, low-resonance steel basket

Polypropylene cone for less distortion and weatherability

Additional voice-coil ventilation

13mm Tweeter with acoustic equalizer and neodymium

magnet

Designer loudspeaker covers

.110 / .205 terminal strip

PowerPlus Speakers

INTRODUCTION

Welcome to Jensen!

This manual is designed to provide information for the owner, salesperson and installer. For those of you who want quick information on how to install this product, please turn to the Installation Section of this manual. Other information can be located by using the Table of Contents. We at Jensen have worked very hard to make sure all the information in this manual is current. But, as we are constantly finding new ways to improve our product, this information is subject to change without notice.

Installation .......................................................................Page 3

Specifications ..................................................................Page 5

Warranty..........................................................................Page 6

If, after reading your manual, you still have questions regarding this product, we recommend that you see your Jensen dealer. If you need further assistance, you can call us direct at 1-800-323-

4815.

Be sure to have your model number and date of purchase available when you call. Please read your warranty clearly and retain your receipt for possible future use.

Preparation

Disconnect battery cable from negative(-)battery terminal.

WARNING: Check vehicle's owner's manual before disconnecting the battery. Disconnecting the battery in some vehicles may require an anti-theft code when reconnecting. Some vehicles may run rough after reconnecting the battery and require that the on-board computer be reset at the dealership. Check with your local dealer if you are uncertain.

Check all safety regulations in your vehicle's owner's manual.

To ensure an obstacle-free fit, check and double check

mounting depth of the speakers against available depth, as well as the location of window mechanics, door handles, and window handles.

If using provided grilles, be sure mounting location is sufficient

distance from door and/or window handles.

Required Tools

The following is a list of tools needed for installation:

#2 Philips screwdriver

Battery post wrench

Hand held drill w/assorted bits

Wire strippers

Wire crimpers

Wire cutters

Since some of these Jensen full range speakers are most often used as direct replacements for stock speakers, some of the following instructions will not apply. For custom installations see your authorized Jensen dealer.

INSTALLATION

Basic Installation Steps

FIGURE 2 - CONNECTING SPEAKER WIRES

Step 1 Step 2

Step 3

Step 4 Step 5 Step 6

: Remove existing speaker. : Position new speaker and align with existing mounting

holes.

: Attach the positive (+) and negative (-) speaker terminals

(see FIGURE 2). Be sure to observe proper polarity when connecting the wires (the striped wire is the negative

lead). : If not using factory grilles, attach grille. : Mount speaker (using factory hardware when possible). : Reconnect negative battery terminal.

FIGURE 1 - DOOR PANEL INSTALLATION

Grille

Speaker Door Panel

FIGURE 3 - REAR DECK INSTALLATION

PowerPlus Speakers

INSTALLATION

Installing the Tweeter for the 652C

The separate tweeters included with the 652C have a variety of mounting applications. During installation, make sure the tweeter is positioned and aimed towards the listener's ears.

There is a protective element integrated into the crossover of your PowerPlus tweeter, which has high impedance in cases of overload and reduces the current flowing through the tweeter. If the tweeter is deactivated, please turn down the volume and wait for a moment. After cooling down,

NOTE

the tweeter will re-activate and become ready for operation again.

FIGURE 6 - WIRING THE SPEAKER/TWEETER

FIGURE 5 - FLUSH MOUNTINGFIGURE 4 - SURFACE MOUNTING

SPECIFICATIONS

PP525 PP652 PP652C PP682 PP693

Midrange Diameter

Frequency Response

Crossover Frequency

Power Handling

Sensitivity

Mounting Depth

Impedence

5" 6.5" 6..5" 6" x 8" 6" x 9"

90Hz - 20kHz (-3dB) 70Hz - 20kHz (-3dB) 70Hz - 20kHz (-3dB) 75Hz - 20kHz (-3dB) 50Hz - 20kHz (-3dB)

4kHz 3kHz 3kHz 3kHz 3kHz

50 Watts Nominal 60 Watts RMS 60 Watts RMS 55 Watts Nominal 80 Watts Nominal

250 Watts Peak 300 Watts Peak 300 Watts Peak 275 Watts Peak 400 Watts Peak

90dB (1 watt @ 1 meter) 91dB (1 watt @ 1 meter) 91dB (1 watt @ 1 meter) 91dB (1 watt @ 1 meter) 91dB (1 watt @ 1 meter)

49mm (2") 56mm (2.25") 56mm (2.25") 56mm (2.25") 74mm (3")

4 ohms 4 ohms 4 ohms 4 ohms 4 ohms

+ 15 hidden pages