Para obtener instrucciones en Español, diríjase a la página 7.
Pour des instructions en Francais, référez-vous à la page 13.
Thank you for purchasing this quality Jensen product!
Carbon speaker system is the ultimate complement to your car
stereo system.
fiberglass cones, rubber surrounds, and silk domed tweeters with
Neodymium magnets, offers unparalleled audio reproduction. The
Carbon series will deliver the natural sound you have come to
expect from Jensen.
The speaker system should be connected to your car radio or an
additional car stereo amplifier, which we recommend for even
better sound quality. Technical data plus installation tips and
further advice are contained in this instruction manual.
The Carbon series, featuring carbon fiber and
Your new
Highlighted Features
Warp resistant, low-resonance steel basket
!
Carbon fiber and fiberglass cones
!
Silk dome tweeters featuring Neodymium magnets
!
Black chrome low profile ABS grilles
!
External in-line crossovers
!
1
CARBON Speakers
INTRODUCTION
>>
Welcome to Jensen!
This manual is designed to provide information for the owner,
salesperson and installer. For those of you who want quick
information on how to install this product, please turn to the
Installation Section of this manual. Other information can be
located by using the Table of Contents. We at Jensen have
worked very hard to make sure all the information in this manual is
current. But, as we are constantly finding new ways to improve our
product, this information is subject to change without notice.
If, after reading your manual, you still have questions regarding
this product, we recommend that you see your Jensen dealer. If
you need further assistance, you can call us direct at 1-800-323-
4815.
Be sure to have your model number and date of purchase
available when you call. Please read your warranty clearly and
retain your receipt for possible future use.
Preparation
!
Disconnect battery cable from negative(-)battery terminal.
WARNING: Check vehicle's owner's manual before
disconnecting the battery. Disconnecting the battery in
some vehicles may require an anti-theft code when
reconnecting. Some vehicles may run rough after
reconnecting the battery and require that the on-board
computer be reset at the dealership. Check with your local
dealer if you are uncertain.
Check all safety regulations in your vehicle's owner's manual.
!
To ensure an obstacle-free fit, check and double check
!
mounting depth of the speakers against available depth, as
well as the location of window mechanics, door handles, and
window handles.
If using provided grilles, be sure mounting location is sufficient
!
distance from door and/or window handles.
Required Tools
The following is a list of tools needed for installation:
#2 Philips screwdriver
!
Battery post wrench
!
Hand held drill w/assorted bits
!
Wire strippers
!
Wire crimpers
!
Wire cutters
!
Since some of these Jensen full range speakers are most often
used as direct replacements for stock speakers, some of the
following instructions will not apply. For custom installations see
your authorized Jensen dealer.
2
INSTALLATION
Basic Installation Steps
FIGURE 2 - CONNECTING SPEAKER WIRES
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
: Remove existing speaker.
: Position new speaker and align with existing mounting
holes, when possible.
: Attach the positive (+) and negative (-) speaker terminals
to both the woofer and tweeter (see FIGURE 2). Be sure
to observe proper polarity when connecting the wires.
: If not using factory grilles, attach grille.
: Mount speaker (using factory hardware when possible).
: Reconnect negative battery terminal.
FIGURE 1 - DOOR PANEL INSTALLATION
Grille
SpeakerDoor Panel
Copper Wire = Positive
Silver Wire = Negative
FIGURE 3 - REAR DECK INSTALLATION
3
CARBON Speakers
>>
INSTALLATION
Installing the Tweeter for the 65C
The separate tweeters included with the 65C have a variety of
mounting applications. During installation, make sure the tweeter
is positioned and aimed towards the listener's ears.
There is a switch inside the Carbon 65C crossover
that can be used to adjust tweeter attenuation. 0dB is
for a flat tweeter response curve relative to the
woofer, while +3dB will boost the tweeter's frequency
response by 3dB throughout it's frequency range.
Placement of this switch will depend on tweeter
NOTE
positioning and listener preference. You may want to
try different positions of this switch before final
installation is complete.