MCD5090
DIGITALAUDIO
COMPACT
MODE
MUTE
BANDBAND
A/PS
EQ/LD
LOC
65
4321
INT RPT RDM
-10
+10
AUX INAUX IN
PUSH
SEL
marine
Installation and Operation Manual
MCD5090
MARINE CD PLAYER / RECEIVER
MCD5090
REWRITABLE
RECORDABLE
Insert label Do not bend.
Never touch
the under side
of the disc.
Wipe clean from
the center to the
edge.
side up.
SAFETY INFORMATION
When Boating
Keep the volume level Iow enough to be aware of your surroundings.
Protect from Water
Do not expose the product directly to water, as this can cause electrical shorts, fire or other
damage.
Protect from High Temperatures
Exposure to direct sunlight for an extended period of time can produce very high temperatures
inside your vessel. Give the interior a chance to cool down before starting playback.
Do not mount radio within close proximity of engine compartment.
Use the Proper Power Supply
This product is designed to operate with a 12 volt DC negative ground battery system.
Protect the Disc Mechanism
Avoid inserting any foreign objects into the disc slot. Misuse may cause malfunction or
permanent damage due to the precise mechanism of this unit.
CAUTION:
THIS MOBILE CD PLAYER IS A CLASS I LASER PRODUCT. THIS UNIT USES A VISIBLE/
INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION IF EXPOSED
DIRECTLY. BE SURE TO OPERATE THE MOBILE CD PLAYER AS INSTRUCTED.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OR PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF. PLEASE REFER
SERVICING TO A QUALIFIED TECHNICIAN.
WAR NING:
• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING
INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.
DISC NOTES
Compatible Disc Types
Table 1: General Disc Information
Disc Type Logo
Audio CD 12 cm single side 74 minutes
NOTE: CD-R and CD-RW discs will not play unless the recording session is closed and
the CD is finalized.
Disc Maintenance
• A dirty or defective disc may cause sound dropouts while playing. Before playing, wipe
the disc using a clean cloth, working from the center hole towards the outside edge.
Never use benzene, thinners, cleaning fluids, anti-static liquids or any other solvent.
• Be sure to use only round CDs for this unit and do not use any special shape CDs. Use of
special shape CDs may cause the unit to malfunction.
• Do not stick paper or tape on the disc. Do not use CDs with labels or stickers attached or
that have sticky residue from removed stickers.
• Do not expose discs to direct sunlight or heat sources such as hot air-ducts, or leave them
in a vessel parked in direct sunlight where there can be a considerable rise in temperature
inside the vessel.
Diameter/
Playable Sides
Playback Time
NOTE: A disc may become scratched (although not enough to make it unusable)
depending on how you handle it and other conditions in the usage environment. These
scratches are not an indication of a problem with the player.
2
MCD5090
182
53
Dashboard
Bend Tabs
Screw Stud
Dashboard
Machine Screw (5 x 25mm)
Hex Nut (5mm)
Hex Nut (5mm)
Rubber Bushing
Screw Stud
Support Strap
Dashboard
Removal Key
INSTALLATION
Before You Begin
1. Disconnect Battery
Before you begin, always disconnect the battery negative terminal.
2. Remove Transport Screws
Important Notes
• Before final installation, test the wiring connections to make sure the unit is connected
properly and the system works.
• Use only the parts included with the unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions.
• Consult with your nearest dealer if installation requires the drilling of holes or other
modifications to your vessel.
• Install the unit where it does not interfere with driving and cannot injure passengers if
there is a sudden or emergency stop.
• If the installation angle exceeds 30º from horizontal, the unit might not give optimum
performance.
• This unit is not waterproof and is intended for interior mounting applications only.
Exterior mounting of the unit requires use of an ASA approved marine housing.
• Avoid installing the unit where it will be subject to high temperatures from direct sunlight,
hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration.
DIN Front Mount
1. Slide the mounting sleeve off of the chassis if it has not already been removed. If it
is locked into position, use the removal
keys (supplied) to disengage it. The
removal keys are depicted in “Removing
the Unit” on page 3.
2. Check the dashboard opening size by
sliding the mounting sleeve into it. If the
opening is not large enough, carefully cut
or file as necessary until the sleeve easily
slides into the opening. Do not force the
sleeve into the opening or cause it to bend
or bow. Check that there will be sufficient space behind the dashboard for the radio
chassis.
3. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve.
With the sleeve fully inserted into the dashboard opening, bend as many of the tabs
outward as necessary to firmly secure the sleeve to the dashboard.
4. Place the radio in front of the dashboard opening so the wiring can be brought through the
mounting sleeve.
5. Follow the wiring diagram carefully and make certain all connections are secure and
insulated with crimp connectors or electrical tape to ensure proper operation.
6. After completing the wiring connections, turn the unit on to confirm operation (vessel
ignition switch must be on). If the unit does not operate, recheck all wiring until the
problem is corrected. Once proper operation is achieved, turn the ignition switch off and
proceed with final mounting of the chassis.
7. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is
fully seated and the spring clips lock it into place.
8. Attach one end of the
perforated support
strap (supplied) to the
screw stud on the rear
of the chassis using the
hex nut and spring
washer provided.
Fasten the other end of
the perforated strap to a
secure part of the
dashboard either above
or below the radio using
the screw and plain
washer provided. Bend
the strap, as necessary, to position it.
CAUTION: The rear of the radio must be supported with the strap to prevent damage to
the dashboard from the weight of the radio or improper operation due to vibration.
9. Test radio operation by referring to the operating instructions for the unit.
Removing the Unit
To remove the radio after installation:
1. Insert fingers into the groove in the front of
frame and pull out to remove the frame.
(When re-attaching the frame, point the
side with a groove downwards and reattach.)
2. Insert the removal keys straight back until
they click, and then pull the radio out. If
removal keys are inserted at an angle,
they will not lock properly to release the
unit.
Trim Plate Installation
Push the trim plate against the chassis until it is
fitted.
Reconnect Battery
When wiring is complete, reconnect the battery
negative terminal.
3
WIRING
+12V DC SWITCHED (ACC)
FRONT RIGHT SPEAKER (+)
FRONT RIGHT SPEAKER (-)
FRONT LEFT SPEAKER (+)
FRONT LEFT SPEAKER (-)
DIMMER
NO CONNECTION
AUTO ANTENNA OUTPUT
REAR RIGHT SPEAKER (-)
REAR RIGHT SPEAKER (+)
REAR LEFT SPEAKER (-)
REAR LEFT SPEAKER (+)
GROUND
+12V DC BATTERY
RED
GRAY
GRAY/BLACK
WHITE
WHITE/BLACK
ORANGE
EMPTY
BLUE
PURPLE/BLACK
PURPLE
GREEN/BLACK
GREEN
BLACK
YELLOW
PIN NO. WIRE COLOR FUNCTION
10 AMP FUSE
7
14
1
8
+12V DC
Battery
+12V DC
SWITCHED
GROUND
DIMMER
MCD5090
4
MCD5090
1
4
6
8
2
3
5
10
16
9
11
12
13
14
21
15
20
19
18
7
17
MCD5090
DIGITALAUDIODIGITALAUDIO
COMPACTACT
MODE
MUTE
BAND
A/PS
EQ/LD
LOC
65
4321
INT RPT RDM
-10
+10
AUX INAUX IN
PUSH
SEL
marine
BASIC OPERATION
Auxiliary Input Operation
You can connect another audio/video system to the unit using the AUX IN input (20) on the
front panel of the unit. Once the device is connected, press the MODE button (5) on the front
panel to select “AUX” mode.
Audio Menu
Press the audio control (PUSH SEL) knob (4) to access the Audio Menu. You can navigate
through the Audio Menu items by pressing the audio control knob repeatedly. Once the desired
menu item appears on the display, adjust that option by turning the audio control knob within
10 seconds. The unit will automatically exit the Audio Menu after six seconds of inactivity. The
following menu items can be adjusted.
Bass Level (BA)
Use the audio control knob to adjust the Bass level range from “-7” to “+7”.
Treble Level (TR)
Use the audio control knob to adjust the Treble level range from “-7” to “+7”.
Balance (BL)
Use the audio control knob to adjust the Balance between the right and left speakers from “R 9”
(full right) to “L 9” (full left). “0” represents an equal balance between the right and left
Power On/Off ( )
Press the button (1) to turn the unit on or off.
Volume Control
To increase the volume, turn the audio control knob (4) clockwise.
To decrease the volume, turn the audio control knob counter clockwise. When the volume is
adjusted, the volume level is shown on the display panel as a number ranging from “0” (lowest)
to “63” (highest).
Mute
Press the MUTE button (8) to mute the audio output. “ “ will appear on the LCD panel (7).
Press MUTE again to restore the audio output to the previous level.
Mode
Press the MODE button (5) to select a different mode of operation, as indicated on the LCD
panel (7). Available modes include Tuner, CD, and AUX IN.
Equalizer (EQ)
The preset equalizer applies preset sound effects to the unit’s audio output signal. To adjust
the preset equalizer, press the EQ/LD button (15). Press repeatedly to choose between the
following modes: OFF, POP, ROCK, CLAS.
speakers.
Fader (FD)
Use the audio control knob to adjust the Fader between the front and rear speakers from “R 9”
(full rear) to “F 9” (full front). “0” represents an equal balance between the front and rear
speakers.
Clock Set
• In clock display mode, press the audio control (PUSH SEL) knob (4) for 2 seconds to
enter clock adjustment mode.
• While the hour is flashing, turn the audio control knob (4) to adjust the value as follows:
• USA Tuning Mode: 1-12
• EURO Tuning Mode: 00 - 23
• Press the audio control (PUSH SEL) knob to confirm the hours.
• While the minutes are flashing, rotate the audio control knob to change the value (from 00
to 59).
• Press and hold the audio control (PUSH SEL) knob for 2 seconds to confirm the time and
exit clock adjustment mode.
Reset
Use a pencil or any non-metallic object to press and hold the reset button (17) for five seconds
to reset the main unit. The unit will return to the factory default settings.
Loudness (LD)
When listening to music at low volume levels, this feature will boost the bass and treble ranges
to compensate for the characteristics of human hearing. Press and hold the EQ/LD button (15)
to activate this feature. “LOUD” appears on the display panel. Press and hold the EQ/LD
button again to turn the LOUD function off.
5
MCD5090
1
4
6
8
2
3
5
10
16
9
11
12
13
14
21
15
20
19
18
7
17
MCD5090
DIGITALAUDIO
COMPCOMPACTACT
MODE
MUTE
BAND
A/PS
EQ/LD
LOC
65
4321
INT RPT RDM
-10
+10
AUX INAUX IN
PUSH
SEL
marine
TUNER OPERATION
Select a Band
Press the BAND button (21) on the control panel to change between three FM bands and two
AM bands. Each band stores up to six preset stations.
Tuning
Manual Tuning
Press the up >>| (19) or down |<< button (18) for less than one second to change the radio
frequency number up or down one step.
Auto Seek Tuning
Press the up >>| (19) or down |<< button (18) for more than three seconds to move to the next
station automatically.
Preset Scan
Select a band (if needed). Press the A/PS button (16) to scan stations stored in the current
band. The unit will pause for eight seconds at each preset station. Press A/PS again to stop
scanning when the desired station is reached.
Stereo
The unit will automatically pick up a stereo signal, when available. When in stereo mode, the
“ ” icon appears in the display. When no stereo signal is available, the unit will automatically
revert to mono operation, and no icon will be displayed.
Local/Distant (LOC)
Press the LOC button (6) to choose between Local (LOC) or Distance (DX) mode. This feature
is used to designate the strength of the signals at which the radio will stop during automatic
tuning. “Distance” is the default setting, allowing the radio to stop at a broader range of signals.
To set the unit to select only strong local stations during automatic tuning, press the LOC
button until “LOC” appears in the display.
USA/EURO Tuning
Use the BAND button (21) switch between USA and European broadcast tuning.
1. Turn the vessel ACC on and the radio off.
2. Press and hold the BAND button for 5 seconds.
The LCD will display either “USA” or “EUR” as the new tuning region.
Preset Stations
Six numbered preset buttons store and recall stations for each band.
Store a Station
Select a band (if needed), then select a station. Press and hold a preset button (9-14) for three
seconds. The preset number will appear in the display.
Recall a Station
Select a band (if needed). Press a preset button (9-14) to select the corresponding stored
station.
Automatically Store / Preset Scan
Automatically Store
Select a band (if needed). Press the A/PS button (16) for more than three seconds to
automatically select six strong stations and store them in the current band. The new stations
replace any stations already stored in that band.
6
MCD5090
1
4
6
8
2
3
5
10
16
9
11
12
13
14
21
15
20
19
18
7
17
MCD5090
DIGITALAUDIO
COMPACT
MODE
MUTE
BAND
A/PS
EQ/LD
LOC
65
4321
INT RPT RDM
-10
+10
AUX INAUX IN
PUSH
SEL
marine
CD OPERATION
Random Play (RDM 4)
Press the RDM 4 button (12) on the control panel during disc play to play all tracks on a CD in
random, shuffled order. Press RDM 4 again to stop random play.
Insert and Eject Disc
Insert a disc, label-side up, with the unit turned on. “Cd” will display on the LCD (7) and then
unit will play the first track on the disc. Press the eject button (2) to stop disc play and eject
the disc. The unit does not have to be turned on to eject the disc.
NOTE: If powered off, the unit will automatically power on when a CD is inserted.
Controlling Disc Playback
Track Select
• Press the >>| (19) or |<< button (18) for less than one second to advance to the next track
on the CD. CD play begins when the button is released.
•Press the -10 button (13) to skip ten tracks backward.
• Press the +10 button (14) to skip ten tracks forward.
• Press and hold the >|| 1 button (9) to begin playback from the first track on the disc.
• Press and hold the >>| (19) or |<< button (18) for >2 seconds to fast forward or fast
reverse through the disc.
Play/Pause Disc Playback (>|| 1)
Press the >|| 1 button (9) to suspend disc play. Press the >|| 1 button again to resume disc
Play.
Intro Scan (INT 2)
Press the INT 2 button (10) on the control panel to play the first 10 seconds of each track
sequentially. Press INT 2 again to stop Intro Scan and resume normal play at the current track.
Repeat Play (RPT 3)
Press the RPT 3 button (11) during disc play to repeat play the current track. Press RPT 3
again to stop repeat play.
7
MCD5090
SPECIFICATIONS
CD
Signal to Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >
Sampling Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.1Khz
Quantization Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 bit
Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20,000Hz
Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Channel (Stereo)
FM Radio
USA Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87.5-107.9MHz
EURO Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87.50-108.00MHz
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <
Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25dB at 1KHz
S/N Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50dB
AM/MW
USA Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530-1710KHz
EURO Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522-1620KHz
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <
S/N Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40dB
General
Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC 11 -14.4
Grounding System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Negative Ground
Speaker Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ohms
Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40W x 4
15dB at S/N 30dB
70dB
45dB
TROUBLESHOOTING
Symptom Cause Solution
No power The vessel’s ignition is not onIf the power supply is properly
The fuse is blown Replace the fuse.
Disc cannot be loaded or
ejected
No sound Volume is too low Adjust volume to audible level.
The operation keys do
not work
Sound skips The installation angle is
Cannot tune to radio station, auto-seek does not
work
ERROR 1 Mechanism Error Press the eject button to correct
ERROR 2 Servo Error Press the eject button to correct
Presence of CD disc inside
the player
Inserting the disc in reverse
direction
Compact disc is extremely
dirty or disc is defective
Temperature inside the vessel is too high
Condensation Leave the player off for an hour or
Wiring is not properly connected.
The built-in microcomputer
is not operating properly
due to noise
more than 30 degrees.
The disc is dirty or defective.
The antenna cable is not
connected.
The signals are too weak. Select a station manually.
connected to the vessel accessory terminal, switch the ignition
key to “ACC”.
Remove the disc in the player and
insert the new one.
Insert the compact disc with the
label facing upward.
Clean the disc or try to play a new
one.
Wait until the ambient temperature returns to normal.
so, then try again.
Check wiring connections.
Press the reset button (17).
Adjust the installation angle to
less than 30 degrees.
Clean the disc and try to play
again or use new disc.
Insert the antenna cable firmly.
the problem.
If the error code does not disappear, consult your nearest service dealer.
the problem.
If the error code does not disappear, consult your nearest service dealer.
8
MCD5090
9
ASA Electronics Corporation
www.asaelectronics.com
www.jensenmarinedirect.com
©2012 ASA Electronics Corporation
v.062112
Loading...