Jensen JBS-350 User Manual

Wall Mountable Bluetooth Music System

with CD

USER MANUAL
JBS-350

PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS

UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

1

DEAR JENSEN® CUSTOMER

Selecting fine audio equipment such as the unit you've just purchased is only the start
of your musical enjoyment. Now it's time to consider how you can maximize the fun
and excitement your equipment offers. This manufacturer and the Electronic
Industries Association's Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the sound come through
loud and clear without annoying blaring or distortion and, most importantly, without
affecting your sensitive hearing. Sound can be deceiving. Over time your hearing
"comfort level" adapts to higher volumes of sound. So what sounds "normal" can
actually be loud and harmful to your hearing. Guard against this by setting your
equipment at a safe level BEFORE your hearing adapts.

To establish a safe level:

Start your volume control at a low setting.
Slowly increase the sound until you can hear it comfortably and clearly, and
without distortion.

Once you have established a comfortable sound level:

Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the
future. After all, we want you listening for a lifetime.

We Want You Listening For a Lifetime
Used wisely, your new sound equipment will provide a
lifetime of fun and enjoyment. Since hearing damage
from loud noise is often undetectable until it is too late,
th

is manufacturer and the Electronic Industries
Association's Consumer Electronics Group
recommend you avoid prolonged exposure to
excessive noise.

Customer's Record:
The serial number of this product is found on its back cover. You should note the serial
number of this unit in the space provided as a permanent record of your purchase to
aid in identification in the event of theft of loss.

Model Number: JBS-350 Serial Number:

________________

EST 19 24

EIA

E

L

E

C

T

R

O

N

I

C

I

N

D

U

S

T

R

I

E

S

•

A

S

S

O

C

I

A

T

I

O

N

•

We
Want You

LISTENING

For A Lifetime

2

IMPORTANT SAFETY INSTRUCTIONS

When used in the directed manner, this unit has been designed and manufactured to
ensure your personal safety. However, improper use can result in potential electrical
shock or fire hazards. Please read all safety and operating instructions carefully
before installation and use, and keep these instructions handy for future reference.
Take special note of all warnings listed in these instructions and on the unit.

1. Read these instructions – All the safety and operating instructions should be read

before the appliance is operated.

2. Keep these instructions – The safety and operating instructions should be kept

for future reference.

3. Heed all warnings – All warnings on the appliance and in the operating

instructions should be adhered to.

4. Follow all instructions – All operation and use instructions should be followed.

5. Do not use this apparatus near water – The appliance should not be used near

water; for example, near a bath tub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.

6

. Clean only with dry cloth – The appliance should be cleaned only as

recommended by the manufacturer.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions. The appliance should be situated so that its location
or position does not interfere with its proper ventilation. For example, the
appliance should not be situated on a bed, sofa, rug, or similar surface that may
block the ventilation openings; or placed in a built-in installation, such as a
bookcase or cabinet that may impede the flow of air through the ventilation
o

penings.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

9. AC adaptor is used as disconnect device and it should remain readily operable

during intended use. In order to disconnect the apparatus from the mains
completely, the AC adaptor should be disconnected form the mains socket outlet
completely.

10. Only use attachments / accessories specified by the manufacturer.
1

1. Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.

12. Unplug this apparatus during lightning storms or when unused for long periods of
time.

13. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liqu

id has been spilled or objects have fallen into the apparatus, the

a

pparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

14. This appliance shall not be exposed to dripping or splashing water and that no
object filled with liquids such as vases shall be placed on the apparatus.

15. Power Sources – The appliance should be connected to a power supply only of
the type described in the operating instructions or as marked on the appliance.
Do not overload wall outlet.

3

16. Battery shall not be exposed to excessive heat such as sunshine, fire or the like

17. Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type.

18. Do not attempt to dismantle, open or repair this product yourself. If a fault occurs,
seek advice from your local qualified service technician or contact the distributor
via the telephone number at the back of this instruction manual.

19. Caution marking and nameplate are located on back of product.

IMPORTANT NOTE

Avoid installing the unit in locations described below:
 Places exposed to direct sunlight or close to heat radiating appliances such as

electric heaters.

 Places subject to constant vibration.
 Dusty, humid or moist places.
 Sources of electrical noise such as fluorescent lamps or motors.
 In case of malfunction due to electrostatic discharge, the apparatus has to be reset

by disconnecting AC adaptor from mains supply, wait at least for 10 minutes before
reconnect the AC adaptor.

COMPLIANCE WITH FCC REGULATIONS

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may

cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio / TV technician for help.

CAUTION: Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

4

CAUTION

Follow the advice below for safe operations.
ON PROTECTION AGAINST LASER ENERGY EXPOSURE

o As the laser beam used in this compact disc player is harmful to the eyes,

do not attempt to disassemble the casing.

o Stop operation immediately if any liquid or solid object should fall into the

cabinet.

o Do not touch the lens or poke at it. If you do, you may damage the lens and

the player may not operate properly.

o Do not put anything in the safety slot. If you do, the laser diode will be ON

when the CD door is still open.

o This unit employs a laser. The use of controls or adjustment or performance

of procedures other than those specified here may result in exposure to
hazardous radiation.

ON SAFETY

 When connecting and disconnecting the AC power, grip the AC adaptor plastic

body and not the cord itself. Pulling the cord may damage it and create hazard.

 When you are not going to use the unit for a long period of time, disconnect the AC

adaptor from the wall outlet and remove all batteries.

ON AC VOLTAGE

 Before use, check that the rated voltage of your unit matches your local voltage.

ON CONDENSATION

 When left in a heated room where it is warm and damp, water droplets or

condensation may form inside the CD player.

 When there is condensation inside the unit, the unit may not function normally.
 Let it stand for 1 to 2 hours before turning the power on, or gradually heat the room

up and dry the unit before use.

Should any trouble occur, disconnect the AC power cord and refer servicing to
qualified personnel.

PROTECT YOUR FURNITURE

This product is equipped with non-skid rubber 'feet' to prevent the product from moving when
you operate the controls. These 'feet' are made from non-migrating rubber material specially
formulated to avoid leaving any marks or stains on your furniture. However certain types of oil
based furniture polishes, wood preservatives, or cleaning sprays may cause the rubber 'feet'
to soften, and leave marks or a rubber residue on the furniture. To prevent any damage to
your furniture we strongly recommend that you purchase small self-adhesive felt pads,
available at hardware stores and home improvement centers everywhere, and apply these
pads to the bottom of the rubber 'feet' before you place the product on fine wooden furniture.

5

INSTALLATION OPTIONS

ATTACHING THE STAND

Align the top portion of the stand with the mounting area located on the bottom of the
main unit. Once in place, the round mounting on the stand will align with the circular
mounting tab located on the back of the unit. A “click” sound is heard when the stand
is attached. Check that the base is locked firmly in place and does not come off. To
remove the stand, press on the mounting tab to unlock the stand, and pull down to
remove the stand, see illustration below:

FOR WALL MOUNTING (STAND REMOVED)

It’s important to be sure there are no electric, gas or water lines located behind the
wall where you are attaching the unit. We recommend having this speaker
professionally installed. Use the included wall mounting accessories and template to
attach the sound bar to the wall.

1. Use the supplied wall mounting instruction sheet to make marks on the wall for

the plastic anchors. Make sure the marks are level before drilling.

2. Drill ¼” holes

on the marks.

3

. Insert the included plastic anchors into the holes until they are flush with the wall.

4. Attach the 2 included spacer sleeves to the wall using the included screws, and

tighten the screws.

5. When the screws are tightened, the screw heads should be about ¼” away from

the spacer sleeves. Line up the keyhole slots located on the back of the main unit
with screws in the wall, see illustration below:

6

6

142 mm

4

Screw

Spacer Sleeves

Wall plugs
plastic

7

LOCATION OF CONTROLS

MAIN UNIT

2

1

33

4

7

5

6

19

19

FRONT VIEW

BACK VIEW