Jenn-Air JXU9130W, JXU9136W Dimension Guide

30" (76.2cm) and 36" (91.4cm) Commercial Style Wall-Mount Canopy Range Hood

PRODUCT MODEL NUMBERS LOCATION REQUIREMENTS

VENTING REQUIREMENTS

JXU9130W JXU9136W

●

A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.

Ref. W10274318A

10/06/2009

ELECTRICAL REQUIREMENTS

Rear discharge

This range hood can be vented directly out the back using the 3¹⁄₄" x 10" (8.3 cm x 25.4 cm) rectangular damper (supplied) along with a 3¹⁄₄" x 10" (8.3 cm x 25.4 cm) rectangular vent system (not supplied). See “Install Range Hood” section for details for installing the damper.

Calculating Vent System Length

To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.

3¹⁄₄" x 10" (8.3 cm x 25.4 cm) Vent System Vent Piece

3¹⁄₄" x 10" (8.3 cm x 25.4 cm) 5.0 ft 90° elbow (1.5 m)

3¹⁄₄" x 10" (8.3 cm x 25.4 cm) 12.0 ft flat elbow (3.7 m)

3¹⁄₄" x 10" (8.3 cm x 25.4 cm) 0.0 ft wall cap (0.0 m)

Maximum equivalent vent length is 35 ft (10.7 m).

Example vent system

Maximum Recommended Length = 35 ft (10.7 m)

1 - 90° elbow = 5.0 ft (1.5 m) 8 ft (2.4 m) straight = 8.0 ft (2.4 m) 1 - wall cap = 0.0 ft (0.0 m)

Length of 3¹⁄₄" x 10" = 13.0 ft (3.9 m) (8.3 cm x 25.4 cm) system

Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located behind the left filter on the rear wall of the vent hood.

Canopy hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

PRODUCT DIMENSIONS

Roof Venting Wall Venting

(top or rear discharge)

.Roof cap

¹⁄₄

" x 10" (8.3 x 25.4 cm)

B. 3

rectan

ular metal vent

A. Wall cap

¹⁄₄

" x 10" (8.3 x 25.4 cm)

B. 3

rectan

ular metal vent

IMPORTANT:

Minimum distance “X”: 30" (76.2 cm) Suggested maximum distance “X”: 36" (91.4 cm)

CABINET DIMENSIONS

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice.

Ref. W10274318A

10/06/2009

clearance upper

cabinet to countertop

countertop height

cabinet opening width

(If installed between cabinets)

Min. cabinet

opening width

Bottom of canopy

to cooking surface

A. 76" (193.0 cm) minimum for

installations with canopy only.

B. 88" (223.5 cm) minimum for

installations with optional duct cover.