JENN-AIR JJW8630DDB, JJW8627DDW, JJW8627DDS, JJW8627DDQ, JJW8627DDB Installation Instructions
...
INSTALLATION
Built-In 27²²²² &30²
²
²²
INSTRUCTIONS
27²²²² SINGLE WALL OVEN
111/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (Must Support 200 lbs.)
DIMENSIONS
inches cm
A 27 MIN 68.58
B 24 MIN 60.96
C 291/16+
D 24 MIN 60.96
E251/2+
F 29 1/2 74.93
G 26 3/4 67.95
H 25 7/16 64.61
I 4 to 31 10.2 to 78.7
27²²²² DOUBLE WALL OVEN
111/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (MustSupport310 lbs.)
A 27 MIN 68.58
B 24 MIN 60.96
C517/8+
D 24 MIN 60.96
E251/2+
F 52 1/4 132.72
G 26 3/4 67.95
H 25 1/2 64.77
I 4 to 10 10.2 to 25.4
1/16 73.82
1/16 64.77
DIMENSIONS
inches cm
1/16 131.76
1/16 64.77
Electric Wall Ovens
30²²²² SINGLE WALL OVEN
111/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (Must Support 200 lbs.)
DIMENSIONS
inches cm
A 30 MIN 76.20
B 24 MIN 60.96
C 291/16+
D 24 MIN 60.96
E281/2+
F 29 1/2 74.93
G 29 3/4 75.57
H 25 7/16 64.61
I 4 to 31 10.2 to 78.7
30²²²² DOUBLE WALL OVEN
111/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (MustSupport310 lbs.)
A 30 MIN 76.20
B 24 MIN 60.96
C517/8+
D 24 MIN 60.96
E281/2+
F 52 1/4 132.72
G 29 3/4 75.57
H 25 1/2 64.77
I 4 to 10 10.2 to 25.4
1/16 73.82
1/16 72.39
DIMENSIONS
inches cm
1/16 131.76
1/16 72.39
403 WEST FOURTH STREET, NORTH
NEWTON, IA 50208
SINGLE WALL OVEN
1
2
D
C
E
I
Art #: 9220-025
B
A
H
F
G
Z
DOUBLE WALL O VEN
B
A
D
C
1
2
H
F
NOTES
Z Donotblockairexhaustslotsalong bottom
of oven.
Y Gas or electric cooktops may be installed
over ovens. See cooktop installation
instructionsfor cutout size.**
W Electricalconnection for electric cooktop
mustinadjacentaccessiblelocation.Cook
top and wall oven must be on separate
120/240 or 120/208 volt 60 Hz AC circuits.
CAUTION
For European style cabinets (flush
front) the required clearance for
operation of the oven door is
minimum spacing of 7/8 ² between
the cutout and the door, hinge or
30²²²² WALL OVEN UNDER COUNTER
111/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (Must Support 200 lbs.)
DIMENSIONS
inches cm
A 25 63.50
B 24 MIN 60.96
C 291/16+
D 24 MIN 60.96
E 28 1/2 72.39
F 29 1/2 74.93
G 29 3/4 75.57
H 25 7/16 64.61
I 36 91.44
J11/2 3.81
1/16 73.82
drawer of the cabinet.
Some built-in cabinets may not be
wide enough, due to their construction, to allow this installation.
K All JA Cooktops 3 MAX 7.62MAX
30²²²² WALL OVEN
inches cm
NOTE: * Hole must be cut as close to corner of cabinet as possible.
** See dealer for approved cooktops.
I
E
Art #: 9220-026
Z
G
UNDER COUNTER WALL OVEN
See pages 5, 6 and 7 for detailed installation
instructions.
J
I
W
B
K
Y
C
1
2
D
E
Art #: 9220-027
A
H
G
Z
8101P602-60
(11-03-00)
F
INSTALLATION
INSTRUCTIONS
Built-In 27²²²² &30²²²² Electric
Combination Wall Ovens
403 WEST FOURTH STREET, NORTH
NEWTON, IA 50208
27² WALL OVEN DESCRIPTION
11-1/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (Must Support 275 lbs.)
DIMENSIONS
in cm
A 27 MIN 68.58 MIN
B 24 MIN 60.96 MIN
C51-7/8+
D 24 MIN 60.96 MIN
E25-1/2+
F 52-15/16 134.46
G 26-3/4 67.95
H 25-7/16 64.61
I 4 to 10 10.2 to 25.4
* Hole must be cut as close to corner of cabinet as possible.
1/16 131.76 + .16
1/16 64.77 + .16
NOTES
Z Do not block air exhaust slots along bottom of
oven.
30² WALL OVEN DESCRIPTION
11-1/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (Must Support 275 lbs.)
DIMENSIONS
in cm
A 30 MIN 76.20MIN
B 24 MIN 60.96MIN
C51-7/8+
D 24 MIN 60.96 MIN
E28-1/2+
F 52-15/16 134.46
G 29-3/4 75.57
H 25-7/16 64.61
I 4 to 10 10.2 to 25.4
1/16 131.76 + .16
1/16 72.39 + .16
CAUTION
For European style cabinets (flush front) the
required clearance for operation of the oven door
is minimum spacing of 7/8² between the cutout
and the door, hinge or drawer of the cabinet.
Some built-in cabinets may not be wide enough,
due to their construction, to allow this installation.
COMBINATION WALLOVEN CUTOUT
NOTE:
INSTALLED WALL OVEN OVERLAPS
CUTOUT 15/16² (2.38 CM) AT THE
TOP AND 1/8² (0.32 CM) AT THE
BOTTOM.
THIS MUST BE TAKEN INTO
CONSIDERATION WHEN LOCATING
CUTOUT IF INSTALLED UNIT IS TO
BE CENTERED IN THE CABINET.
B
C
I
A
H
D
1
2
E
Art #: 9220-028
G
F
Z
2
WARNING
Improper installation of the grounding
circuit can result in a risk of electric sho ck.
Consult a qualified electrician or serviceman if the
grounding instructions are not completely understood, if
doubt exists as whether the appliance is properly
grounded.
Installing Bottom Trim Piece
Remove lower screws fromhinge
receptacleplates. Align lowertrim
and reinstallscrews.
CAUTION
For European style cabinets (flush front) the required
clearance for operation of the oven door is minimum
spacing of 7/8² between the cutout and the door, hinge
or drawer of the cabinet.
Some built-in cabinets may not be wide enough, due to
their construction, to allow this installation.
Installation
1. Cut hole in cabinet to mount oven. Cutout in cabinet
should be level and straight.
NOTE: There are no provisions to level the unit after it
is installed. An oven that is not level could cause poor
baking results.
2. Install plywood floor as shown.
3. Remove oven door(s). See Oven Door Removal
procedure.
4. Attach unit to the cabinet with four No. 8 x 1² screws
supplied with unit inside of envelope containing these
instructions. Pre-drill holes in cabinet for attachment
screws using 1/8² drill. Oven mounting holes are
provided in side trim.
5. Install bottom trim.
6. Replace oven door(s). See Oven Door Replacement
procedure.
7. See instructions at right for electrical hook-up.
8. See Use and Care Manual for operating instructions.
DO NOT INSTALL BOTTOM TRIM UNTIL UNIT IS
ATTACHED TO THE CABINET.
Electrical Connections
Unit to be properly circuit protected and wired according
to local electrical code and National Electrical Code.
It is advisable that the electrical wiring and hookup be
accomplished by a competent electrician.
120/240 VAC or 120/208 VAC 60 Hz. See serial plate on
front of unit for power requirements.
The neutral of this unit is grounded to the frame through
the solid grounding wire. (The ground and the white wires
are twisted together at the termination of the conduit.) If
used on new branch-circuit installations (1996 NEC),
mobile homes, recreational vehicles, or in an area where
local codes prohibit grounding through the neutral
conductor, untwist or disconnect the ground wire and
connect to ground in accordance with local code. Connect
the white neutral to the service neutral. Connect all wires
to the branch circuit with approved connectors. Use
copper or aluminum wire. If aluminum wire is used, use
connectors recognized for joining aluminum to copper.
The chart below recommends the minimum circuit
protection and wire size if the appliance is the only unit on
the circuit.
K.W.RATING
ON SERIAL PLATE
0-- 4.8
4.9 -- 6.9
7.0 -- 9.9
10.0 -- 11.9
12.0 -- 14.9
RECOMMENDED MINIMUM
CIRCUIT PROTECTION
IN AMPERS
20
30
40
50
60
WIRE SIZE
(AWG)
12
10
8
8
6
Service
Interrupt the source of electricity to the unit when
attempting to repair or service the oven. Failure to do this
could result in a dangerous or even fatal shock.
IMPORTANT - SAVE FOR LOCAL ELECTRICAL INSPECTOR’S USE
3
Oven Door Removal
For ease of installation, remove oven door(s) before
placing unit into cutout. This will reduce the weight of the
unit by about 35 pounds per door. Remove oven door(s)
as follows:
S Open oven door to the “Full Open” position (see
Figure 1).
S Rotate hinge locking lever DOWN, to unlock hinge
from the unit (see Figure 2).
S Close oven door to the “Removal” position (until it
stops; see Figure 3).
S Grasp the door firmly on each side and lift the door
straight up and off the unit.
NOTE: The oven door is heavy. Be sure you have a
firm grip before lifting the oven door off the unit.
Do not lift the door by the handle!
Oven Door Replacement
Replace oven door(s) after placing unit into cutout.
Replace oven door(s) as follows:
S Grasp oven door firmly on each side, hold oven door
at approximately a 30° angle and align oven door
hinge arm (see Figure 4) with hinge receiver on unit
(see Figure 5).
S Insert oven door hinge arm into hinge receiver until
the hinge arm slots (see Figure 4) align with horizontal
pins on the hinge receiver (see Figure 5) and place
hinge arm onto the hinge receiver.
S Once the hinge arms are resting on the hinge receiver
pins (see Figure 3) open oven door slowly to the “Full
Open” position (see Figure 2).
S Rotate hinge locking lever UP to the locked position to
secure the oven door to the unit (see Figure 1).
NOTE: Make sure that hinge locking lever is rotated fully
UPtothelockedpositionasshown(seeFigure1)
before closing oven door.
Hinge Locking Lever
(Locked Position)
Figure 1
Hinge Locking Lever
(Unlocked Position)
Figure 2
CAUTION
Door will not close all the way and could fall off
when opened if the hinge locking levers are not
rotated fully UP to the locked position.
If hinge locking lever will not rotate fully UP to the locked
position as shown (see Figure 1) then the hinge arm is
not properly seated on the receiver. Rotate the hinge
locking lever DOWN to the unlocked position (see Figure
2) and remove oven door as outlined in the Oven Door
Removal procedure. Then replace the oven door as
outlined in the Oven Door Replacement procedure,
making sure that the hinge arm slots are fully seated on
the horizontal pins in the hinge receiver.
S Once the hinge locking lever is rotated fully UP to the
locked position (see Figure 1) close the oven door.
Hinge Arm
Figure 4
Figure 3
Hinge Arm Slots
Hinge Receiver
HorizontalPins
Figure 5
4
INSTALLATION
30²²²² Under Counter
INSTRUCTIONS
30²²²² WALL OVEN UNDER COUNTER
11-1/4² Dia. Conduit Access Hole*
25/8² Plywood Floor (Must Support 200 lbs.)
See next page for Support Platform Construction
DIMENSIONS
inches cm
A 25 63.50
B 24 MIN 60.96
C 29-1/16 +
D 24 MIN 60.96
E 28-1/2 72.39
I 36 91.44
J 1-1/2 3.81
1/16 73.82
Wall Oven
403 WEST FOURTH STREET, NORTH
30²²²² WALL OVEN
inches cm
K3MAX 7.62MAX
Z Do not block air exhaust slots along bottom of oven.
Y Gas or electric cooktops may be installed over ovens.**
See cooktop installation instructions for cutout size.
W Electrical connection for electric cooktop must in
adjacent accessible location. Cook top and wall oven
must be on separate 120/240 or 120/208 volt
60 Hz AC circuits.
NOTE: * Hole must be cut as close to corner of cabinet
as possible.
NEWTON, IA 50208
NOTES
** See dealer for approved cooktops.
SIDE AND/OR TOP FILLERS
MAY BE NECESSARY IF UNIT
IS POSITIONED BETWEEN
EXISTING CABINETS. BE
SURE THEY ARE ATTACHED
SECURELY, SINCE THEY WILL
ANCHOR THE OVEN IN THE
CABINET.
5
Support Platform
30²²²² Under Counter Wall Oven
6
COOKTOP S HOWN FOR REFERENCE ONLY.
SEE COOKTOP INSTALLATION INSTRUCTIONS FOR CUTOUT SIZE.
3-13/16 MAX
BURNER BOX DEPTH
9220-010
29-1/16 +
WALL OVEN CUT OUT
HEIGHT
3² MAX
SUPPORT PLATFORM HEIGHT
30²²²² Under Counter Wall Oven
with Cooktop
36² MIN
1/16
7
Loading...